This patch reads the memory latency values for all the 8 levels for
SKL. These values are needed for the Watermark computation.
v2: Incorporated the review comments from Damien on register
indentation.
v3: Updated the code to use the sandybridge_pcode_read for reading
memory latencies for GEN9.
v4: Don't put gen 9 in the middle of an ordered list of ifs
(Damien)
v5: take the rps.hw_lock around sandybridge_pcode_read() (Damien)
v6: Use gen >= 9 in the pcode_read() function for data1.
Move the defines near the gen6 ones and prefix them with PCODE.
Remove unused timeout define (the pcode_read() code has a larger
timeout already).
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Pradeep Bhat <pradeep.bhat@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There's some serious confusion regarding ELD valid bit that gets set and
cleared back and forth etc. Rewrite it all based on the documented audio
codec enable/disable sequences.
v3: replace vblank wait with a comment
v4: expand the comment on what should be done with the vblank wait
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make audio related register defines conform to existing style: Add _MASK
where relevant, indent the defines for register contents, don't indent
the defines for register addresses, prefix pipe specific register
address defines with underscores, drop self explanatory comments.
No functional changes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Userspace cares about whether or not swizzling depends on the page
address for its direct access into bound objects. Extend the get_tiling
ioctl to report the physical swizzling value in addition to the logical
swizzling value so that userspace can accurately determine when it is
possible for manual detiling.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Akash Goel <akash.goel@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Testcase: igt/gem_tiled_wc
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Always require PIN_GLOBAL when we want a mappable offset (PIN_MAPPABLE).
This causes the pin to fixup the global binding in cases were the vma
was already bound (and due to the proceeding bug, we considered it to be
already mappable).
References: https://bugs.freedesktop.org/show_bug.cgi?id=85671
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Add WARN_ON to check that PIN_MAP implies PIN_GLOBAL as
discussed on irc.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We use the obj->map_and_fenceable hint for when we already have a
valid mapping of this object in the aperture. This hint can only apply
to the GGTT and not to the aliasing-ppGTT. One user of the hint is
execbuffer relocation, which began to fail when it tried to follow the
hint and perform the relocate through the non-existent GGTT mapping.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=85671
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently we program just DPSCNTR and DSPSTRIDE directly from the ring
interrupt handler, which is fine since the hardware guarantees that
those are update atomically. When we have atomic page flips we'll want
to be able to update also the offset registers, and then we need to use
the vblank evade mechanism to guarantee atomicity. Since that mechanism
introduces a wait, we need to do the actual register write from a work
when it is triggered by the ring interrupt.
v2: Explain the need for mmio_flip.work in the commit message (Paulo)
Initialize the mmio_flip work in intel_crtc_init() (Paulo)
Prevent new flips the previous flip work finishes (Paulo)
Don't acquire modeset locks for mmio flip work
Note: Paulo had reservations about the work item leaking over a plane
disable. But insofar as we do lack these checks that issue is already
present with the existing code.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A follow up patch will call this funcion from a work context for the
mmio flip, in which case we cannot acquire the modeset locks. That's
not a problem though, since the check is there to protect vblank and
the mode, but the code that changes that waits for pending flips
first.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Note that a later patch will use these functions in some other file
and drop the static. Hence the kerneldoc looks appropriate.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Add comment that the functions will become non-static
shortly.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
An earlier commit (c8725f3dc0: Do not call
retire_requests from wait_for_rendering) removed the use of the ring parameter
within wait_rendering__tail() but did not remove the parameter itself. As the
plan is to remove obj->ring which is where this parameter comes from, it is
simpler to just remove the parameter completely than to update it with a new
source.
For: VIZ-4377
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
CC: Chris Wilson <chris@chris-wilson.co.uk>
CC: Brad Volkin <bradley.d.volkin@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With this patch, the RPS sequence for runtime suspend/resume is
exactly like the sequence for S3 suspend/resume:
- flush_delayed_work(&dev_priv->rps.delayed_resume_work)
- intel_runtime_pm_disable_interrupts()
- intel_suspend_gt_powersave()
(suspended)
- intel_runtime_pm_enable_interrupts()
- intel_enable_gt_powersave()
With this, we get rid of WARNs that are currently intermittently
triggered by the system-suspend-execbuf subtest of runtime PM. Notice
that these WARNs could also be triggered in other ways that involved
doing lots of RPM suspend/resume cycles just after a system S3 resume.
Testcase: igt/pm_rpm/system-suspend-execbuf
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reference: https://bugs.freedesktop.org/show_bug.cgi?id=82939
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fix the message, not the fault :)
This is what I see:
[ 282.108597] [drm:i915_check_and_clear_faults] Unexpected fault
[ 282.108597] Addr: 0x00000000\n Address space: PPGTT
[ 282.108597] Source ID: 24
[ 282.108597] Type: 0
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There are two leftover GTIIR writes in valleyview_irq_preinstall().
Looks like the were originally left behind by:
commit d18ea1b58a
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Fri Jul 12 22:43:25 2013 +0200
drm/i915: unify PM interrupt preinstall sequence
and then the GTIIR reset was added back here:
commit f86f3fb005
Author: Paulo Zanoni <paulo.r.zanoni@intel.com>
Date: Tue Apr 1 15:37:14 2014 -0300
drm/i915: properly clear IIR at irq_uninstall on Gen5+
so we can kill the leftovers from the vlv code.
Cc: Paulo Zanoni <przanoni@gmail.com>
Suggested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The extra VLV_IIR writes at the end of vlv_display_irq_postinstall()
serve no purpose. Remove them.
The VLV_IMR/IER/IIR setup at the start of the function also seems a bit
pointless since it doesn't unmask/enable anything. But leave it be for
now.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Split the vlv display irq postinstall code to a separate function so
that we can share it with chv.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull the vlv display irq reset code to a new functions. The aim is to
share the code with chv.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Genralize valleyview_display_irqs_install() and
valleyview_display_irqs_uninstall() enough so that they work on chv.
The only difference to vlv here being the third pipe that chv brings.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Looks like we forgot to call gen5_gt_irq_reset() for vlv in the
uninstall phase. Do so.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Replace the hand rolled IIR,IER,IMR disable sequences with
GEN5_IRQ_RESET().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Follow the same ordering rules for the IIR,IER,IMR writes on vlv/chv
that we do on other gen5+ platforms.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Looks like a leftover POSTING_READ(GEN8_PCU_IIR) in
cherryview_irq_preinstall() from some earlier age. GEN5_IRQ_RESET()
already does the posting read so this changes nothing, so kill it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Replace the hand rolled macros with gen8_gt_irq_reset() and
GEN5_IRQ_RESET() in cherryview_irq_uninstall().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some has given a name for the DPINVGTT status bitmask, so let's use it
instead of the magic number. Looks more like the chv code now.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When disabling interrupts we do the writes in this order:
IMR,IER,IIR,IIR. But when enabling interrupts we don't do use the
mirrored order, and instead do IIR,IIR,IMR,IER.
I like consistency unless there's a good reason against it, which I
can't think of here, so change the enable order to IIR,IIR,IER,IMR.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It will help future code if this function knows something about of the context
of the display setup object is being pinned for.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Write HWS_PGA address even in execlists mode as the global hardware status
page is still required. This address was previously uninitialized and
HWSP writes would clobber whatever buffer happened to reside at GGTT
address 0.
v2: Break out hardware status page setup into a separate function.
Issue: VIZ-2020
Signed-off-by: Thomas Daniel <thomas.daniel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The function was removed in:
commit 037bde19a4
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Thu Mar 27 08:24:19 2014 +0000
Revert "drm/i915: Disable/Enable PM Intrrupts based on the current freq."
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The function was removed in:
commit 0e32b39cee
Author: Dave Airlie <airlied@redhat.com>
Date: Fri May 2 14:02:48 2014 +1000
drm/i915: add DP 1.2 MST support (v0.7)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On pre-ddi platforms we don't shut down the link when changing link
training parameters. Except when clock recovery fails too hard and we
restart with channel eq training. Which doesn't make a lot of sense
really, since just stopping/restarting the DP port at this point
violates the modeset sequence documented in the Bspec.
So let's tempt fate and try this.
This patch is motivated by a WARN_ON triggered by
commit bc76e320f2
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Tue May 20 22:46:50 2014 +0200
drm/i915: Drop now misleading DDI comment from dp_link_down
References: https://bugs.freedesktop.org/show_bug.cgi?id=85670
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Acked-by: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris removed the code using it in:
commit be2d599b5d
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Wed Sep 10 19:52:18 2014 +0100
drm/i915: Remove dead code, i915_gem_verify_gtt
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As Paulo said when introducing the enum, having more types is really
good to document what should go where (int foo(int, int, bool, bool).
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It's really part of the "push all new_* state into current state
pointers" done in that function. So let's move it there to make this
clear.
Also, with the conversion done the num_shared_dpll check the function
does in it's loop is enough, so we can drop the check for the dpll
compute callback, too.
Cc: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Now that shared DPLLs configuration is staged, there's no need to track
the current ones in the new pipe_config since those are released before
making the new pipe_config effective.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There's no users left after the conversion to calculate clocks before
disabling crtcs during mode set.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use the infrastructure added in a previous patch to choose shared DPLLs
and calculate clocks before touching the hardware.
v2: Don't set mode_set hooks since dev_priv is kzalloc()'d (Ville)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use the infrastructure added in a previous patch to choose shared DPLLs
and calculate clocks before touching the hardware.
v2: Don't set mode_set hooks since dev_priv is kzalloc()'d (Ville)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use the infrastructure added in a previous patch to choose shared DPLLs
and calculate clocks before touching the hardware.
v2: Don't set mode_set hooks since dev_priv is kzalloc()'d (Ville)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It is possible for a mode set to fail if there aren't shared DPLLS that
match the new configuration requirement or other errors in clock
computation. If that step is executed after disabling crtcs, in the
failure case the hardware configuration is changed and needs to be
restored. Doing those things early will allow the mode set to fail
before actually touching the hardware.
Follow up patches will convert different platforms to use the new
infrastructure.
v2: Keep pll->new_config valid only during mode set (Ville)
Use kmemdup() in i915_shared_dpll_start_config() (Ville)
Restore old pll config if something fails before commit (Ville)
Don't set compute_clock hooks since dev_priv is kzalloc()'d (Ville)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The new struct will be used in a follow up patch to allow a current and
a staged config to exist for the same shared DPLL.
v2: Rebase on by mask_to_refcount()->hweight32() change. (Damien)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This will be used in a follow up patch to properly release shared DPLLs
without relying on the shared_dpll field in pipe_config.
v2: Fix white space error (Ville)
Use hweight32() (Ville)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
More concise. Noticed while reviewing Ander's patch which touched a
lot of the pipe_has_type checks.
v2: Use new_config in one place Ander spotted.
Cc: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Just various stuff all over from a bunch of people. Shortlog gives a beter
overview, it's really all misc drm patches.
* tag 'topic/core-stuff-2014-11-05' of git://anongit.freedesktop.org/drm-intel:
drm/edid: add #defines and helpers for ELD
drm/dp: Add counters in the drm_dp_aux struct for I2C NACKs and DEFERs
drm: Remove compiler BUG_ON() test
drm: Fix DRM_FORCE_ON_DIGITAL use
drm/gma500: Don't destroy DRM properties in the driver
drm/i915: Don't destroy DRM properties in the driver
drm: Add a note to drm_property_create() about property lifetime
gpu: drm: Fix warning caused by a parameter description in drm_crtc.c
drm/dp-helper: Move the legacy helpers to gma500
drm/crtc: Remove duplicated ioctl code
drm/crtc: Fix two typos
gpu:drm: Fix typo in Documentation/DocBook/drm.xml
gpu: drm: drm_dp_mst_topology.c: Fix improper use of strncat
drm: drm_err: Remove unnecessary __func__ argument
drm: Implement O_NONBLOCK support on /dev/dri/cardN
This shouldn't change the behavior of those functions, since they are
called after the new_config is made effective and that points to the
current config. In a follow up patch, the mode set sequence will be
changed so this is called before disabling crtcs, and in that case
those functions should work on the staged config.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
[danvet: Flatten if by moving the check into the WARN.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
execlists_submit_context() always returns 0, which is redundant.
And its name is inaccurate, since it actually submits (up to)
TWO contextS. So we rename it, change it to "void", and remove
the WARN_ON() testing its return value.
Change-Id: Ie225b0eca7754c6093c8b8bd15550b251b6feb82
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If a ring failed to initialise for any reason then the error path would try to
clean up all rings including those that had not yet been allocated. The ring
clean up code did a check that the ring was valid before starting its work.
Unfortunately, that was after it had already dereferenced the ring to obtain a
dev_private pointer.
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When looking at the bug report logs with triggered
WARN_ON, the person doing bug triaging will have to
find exact kernel source and match file/line.
Attach the condition that triggered the WARN_ON
to kernel log. In most cases the context is self
evident and this way we can save developer time.
The drawback is ~16kbytes bigger i915.ko
Signed-off-by: Mika Kuoppala <miku@iki.fi>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When we suspend we turn everything off so the pps should be idle, and we
also (or at least should) disable all power wells which will reset the
power sequencer port assignment. So when we resume all power sequencers
should be in their reset state. However it's at least theoretically
possible that the BIOS would touch the power seuqencer(s), so to be safe
we ought to read out the current port assignment like we do at driver
init time.
To do that we can simply call vlv_initial_power_sequencer_setup() from
the encoder ->reset() hook before calling intel_edp_panel_vdd_sanitize().
There's no danger or clobbering the pps delays since we now have those
stored within intel_dp and we don't change them once initialized.
This will make sure that the vdd state gets correctly tracked post-resume
in case the BIOS enabled it.
We need to shuffle things around a bit to get the locking right, and
while at it, make intel_edp_panel_vdd_sanitize() static and move it
around a bit to avoid a forward declaration.
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The pps timestamp initialization was accidentally lost on vlv/chv in
commit a4a5d2f8a9
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Thu Sep 4 14:54:20 2014 +0300
drm/i915: Track which port is using which pipe's power sequencer
Restore it so that we avoid introducing random delays into the pps operations
during/after driver init time.
Cc: Imre Deak <imre.deak@intel.com>
Reported-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We'll never end up in the hooks with eld[0] unset, as that's checked by
drm_select_eld().
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Introduce functions to enable/disable the audio codec, incorporating the
ELD setup within enable. The disable is initially limited to HSW,
covering exactly what was done previously.
The only functional difference is that ELD valid is no longer set if
there is no connector with ELD, which should be the right thing to do
anyway. Otherwise the sequence remains the same, with warts and all, in
preparation for applying more sanity.
v2: add kernel doc.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The audio programming sequence states that the ELD must be written and
enabled after the pipe is ready. Indeed, this should clarify the
situation with
commit c79057922e
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Wed Apr 16 16:56:09 2014 +0200
drm/i915: Remove vblank wait from haswell_write_eld
and Ville's review of it [1].
Moreover, we should not touch the relevant registers before we get the
audio power domain.
[1] http://mid.gmane.org/20140416155309.GK18465@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Keep the driver modifications to ELD together. This also sets the
Conn_Type for G4X DP which wasn't done before.
Clean up the debugs while at it; this is all obvious from the connector
name.
v3: add missing ~ (Rodrigo)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It seems that the pipe-a power well has replaced the disp2d power well
on chv. At least that's the case with the current punit firmware. So
enable the pipe-a power and expand its domains to cover everything the
disp2d well ought to cover.
The other power wells (apart from the cmnlane wells) still seem awol
in the current punit firmware. So leave them disabled in the code.
This fixes a hilarious oops during resume on bsw where
intel_hdmi_get_config() would read the port register and get back
0xffffffff and thus think the port is enabled on pipe D. It would then
go and index the pipe_to_crtc_mapping[] array with PIPE_D and blow up
when intel_hdmi_get_config() tries to write to crtc->config. Someone
really ought to replace all naked pipe_to_crtc_mapping[] uses with the
appropriate function call so we could add a warning there if the pipe
doesn't actually exist...
We must also call the power seqeuencer state reset function from
the pipe-a well disable just like we do from disp2d on vlv. Otherwise
the eDP panel won't recover at resume time since the PPS has lost its
hold on the port.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=84903
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CHV has a programmable CSC unit on the pipe B sprites. Program the unit
appropriately for BT.601 limited range YCbCr to full range RGB color
conversion. This matches the programming we currently do for sprites
on the other pipes and on other platforms.
It seems the CSC only works when the input data is YCbCr. For RGB
pixel formats it doesn't matter what we program into the CSC registers.
Doesn't make much sense to me especially since the register names give
the impression that RGB input data would also work. But that's how
it behaves here.
In the review discussions there's been some nice math to explain the
values obtained here. First about the YCbCr->RGB matrix:
"I had the RGB->YCbCr matrix, inverted it and the values came out. But they
should match the wikipedia article. Also keep in mind that the coefficients
are in .12 in fixed point format, hence we need a 1<<12 factor. So let's
try it:
Kb=.114
Kr=.299
(1<<12) * 255/219 ~= 4769
-(1<<12) * 255/112*(1-Kb)*Kb/(1-Kb-Kr) ~= -1605
-(1<<12) * 255/112*(1-Kr)*Kr/(1-Kb-Kr) ~= -3330
(1<<12) * 255/112*(1-Kr) ~= 6537
(1<<12) * 255/112*(1-Kb) ~= 8263
"Looks like the same values to me."
And then about the limits used for clamping:
"> where did you get these min/max?
"The hardware apparently deals in 10bit values, so we need to multiply everything
by 4 when we start with the 8bit min/max values.
Y = [16:235] * 4 = [64:940]
CbCr = ([16:240] - 128) * 4 = [-112:112] * 4 = [-448:448]
"The -128 being the -0.5 bias that the hardware already applied before
the data entered the CSC unit."
Raw data is also supplied in 10bpc in the registers.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by Rodrigo Vivi <rodrigo.vivi@intel.com>
[danvet: Copypaste explanations&math from the review discussion.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We want to run intel_uncore_early_sanitize() before we touch any
registers, because on BDW, when we resume, the FPGA_DBG_RM_NOCLAIM bit
is set, so we need to clear it - through intel_uncore_early_sanitize()
- before we do anything else. With the current code, we don't clear
the bit before our first register access, so we print a WARN
complaining about an unclaimed register error.
v1: Was called "drm/i915: run intel_uncore_early_sanitize earlier on
resume"
v2: Was called "drm/i915: run intel_uncore_early_sanitize earlier on
resume on non-VLV"
v3: This one, on top of the intel_resume_prepare() rework.
v4: Rebase.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because, really, the abstraction is not working for us. It is nice for
VLV, but doesn't add anything useful on SNB/HSW/BDW. We want to change
this code due to a recently-discovered bug, but we can't seem to find
a nice solution that repects the current abstraction. So let's kill
intel_resume_prepare() and its friends, and add an equivalent
implementation to both its callers.
Also, look at the diffstat!
v2: - Rebase.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CHV adds a bunch of new registers for primary plane size/position and
pipe blender setup. Initialize all those registers to avoid nasty
surprises. PRIMSIZE is especially important as without programming it
the outout will be garbled whenever the primary plane size would not
match what the BIOS set up.
Also program the sprite constant alpha register to disable the constant
alpha blending factor. This applies to vlv as well as chv.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In case the cmnlane power well is down but cmnreset isn't asserted we
would currently skip the off+on toggle for the power well. That could
leave cmnreset deasserted while cmnlane is powered down which might
lead to problems with the PHY.
To avoid such issues skip the cmnlane toggle only if both cmnlane and
disp2d wells are up and cmnreset is already deasserted. In all other
cases power down the cmnlane well which will also make sure cmnreset
gets asserted correctly while cmnlane is powered down.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use the macros makes the code cleaner and it also checks for a NULL fb.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
take out pin_fb code so the commit phase can't fail anymore.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Take out the pin_fb code so commit phase can't fail anymore.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The power seqeuencer kick procedure requires the DPLL to be running
in order to complete successfully. In case the DPLL isn't currently
running when we need to kick the power seqeuncer enable it
temporarily. This can happen eg. during ->detect() when the pipe is
not already active.
To avoid needlessly duplicating the DPLL programming re-use the already
existing functions by passing a temporary pipe config to them instead
of having them consult the current pipe config at crtc->config.
v2: Introduce vlv_force_pll_{on,off}() (Daniel)
v3: Rebase due to drm_crtc vs. intel_crtc changes
Fix a typo in commit msg (checkpatch)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com> (v1)
[danvet: Appease checkpatch.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
eDP ports need the power seqeuncer whenever the port is active. Warn if
we accidentally steal the power sequener from an active eDP port. This
should not happen unless there's a bug somewhere else, but it's best to
scream loudly if it happens to help with debugging.
Note that this only checks for active pipes and not for enabled pipes
which are turned off with dpms. Which means we might run the risk that
the pps might get stolen and we can't reacquire one when enabling the
pipe again with dpms on. But on current platforms that's impossible
since we only support two edp ports with just two panel power
sequencers. So a more elaborate scheme which reserves the pps even
when the pipe is inactive isn't required.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
[danvet: Summarize my discussion with Ville about dpms on/off issues.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We should never enable the panel power twice. That would indicate a bug
somewhere else as we would need to enable the port twice without
disabling it in between. Also print the port name.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Print the port name in the VDD/PPS debugs messages.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In case we fumble something and end up picking an already used power
seqeuencer in vlv_power_sequencer_pipe() at least try to steal it
gracefully. In theory this should never happen though.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There's no power sequencer on pipe C on VLV/CHV so scream a bit if we
try to steal one from pipes other than A and B.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
VLV gets confused if two power sequencers have the same port selected.
It would seem the port doesn't start up properly in the is case and
vlv_wait_port_ready() will fail as will the link training. Clearing the
port select in the PP_ON_DELAYS register fixes this problem.
CHV doesn't seem to need this, but it doesn't seem to hurt either so
let's just do it for both to keep the code between the platforms as
uniform as possible.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If there's no power sequencer assigned to the port currently we can't
very well have vdd or panel power enabled either. If we would try to
check that from the pps registers we'd need to pick a power seqeuncer
and kick it. So let's skip the register read and the kick.
Note that there's still a bit an issue about correctly recovering pps
state from resume if the bios is nasty: With this check we'll always
assume that the pps is off. But that's better done in a follow-up
patch and it shouldn't be too harmful - at most we waste time enabling
the pps if it's on already.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
[danvet: Add note about resume issues Imre spotted.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When we pick a new power sequencer for the port but we're not doing a
full modeset, the power sequencer may have locked on to another port (or
no port). So kick it a bit to make sure it controls the port we want.
Again just like when we attempt to actually enable the DP port, we
must first write the port register with the approriate value except
the enable bit, and then we must enable the port to make the power
sequencer happy. In this case since we don't want the port actually
enabled we just toggle it on and immediately back off. Going forward
the power sequencer will keep working on that specific port until again
moved to another port.
v2: Refine the kick procedure
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When switching from one pipe to another, the power sequencer of the new
pipe seems to need a bit of kicking to lock into the port. Even the vdd
force bit doesn't work before the power sequencer has been sufficiently
kicked, so this must be done before any AUX transactions are attempted.
After extensive experimentation I've determined that it's sufficient
to first write the port register with the correct values except the
port must remain disabled, then we can do a second write to enable the
port, after which the power sequencer is operational and allows the port
to start up properly.
Contrary to my earlier theories we don't need to enable the port with
the idle pattern, so let's just use training pattern 1 as that's what
other platforms use here.
v2: Refine the kick procedure
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There's no point in checking if the data lanes came out of reset after
link training. If the data lanes aren't ready link training will fail
anyway.
Suggested-by: Todd Previte <tprevite@gmail.com>
Cc: Todd Previte <tprevite@gmail.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Acked-by: Todd Previte <tprevite@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just grab the pps_mutex once and do all the pps panel startup operations
while holding the mutex instead of grabbing the mutex separately for
each individual step.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We'll be needing to the call the power seqeuencer functions while
already holding pps_mutex, so split the locking out to small wrapper
functions.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since we read the current power seqeuncer delays from the registers
(as well as looking at the vbt and spec values) we may end up
corrupting delays we already initialized when we switch to another
pipe and the power seqeuncer there has different values currently
in the registers.
So make sure we only initialize the delays once even if
intel_dp_init_panel_power_sequencer() gets called multiple times.
There was some discussion in the review about when exactly we need to
unlock the pps. Quoting Bspec:
"If this bit is not a zero, it activates the register write protect
and writes to those registers will be ignored unless the write
protect key value is set in the panel sequencing control register."
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
[danvet: Add Bspec quote per review discussion between Imre and
Ville.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The power seqeuncer delays are fixed for a given panel, so we can keep
them around once computed.
Not that on VLV/CHV we still re-compute them every time we initialize
the power seqeuncer registers, but that will change soon enough.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
want_panel_vdd is a bool so it can't cope with interleaving on/off calls
from multiple threads. If we want to make that possible we'd need to
convert want_panel_vdd into a proper ref count. But an easier fix is to
remove the high level vdd on/off calls from detect/hpd code paths and
just rely on the delayed vdd off to avoid needless vdd on<->off ping
pong.
After this change only the encoder enable/disable paths use the high
level functions, which is fine since both the on and off low level edp
vdd calls from intel_dp_aux_ch() happen without dropping pps_mutex in
between and so want_panel_vdd can't change in between.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Only ports B and C have the power sequencer and backlight controls,
so complain if we ever try to register an eDP connector on some other
port.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because I got annoyed that I had to document what values "int
ddi_personality" is supposed to hold.
A good side-effect of this change is that now the compilers can do
some additional checks on our code, which may prevent some bugs in the
future. A bad side-effect of this change is that now the compilers do
some additional checks on our code and complain when a switch
statement doesn't check for all possible values, so we need to add
"default" cases to all those switches. Hopefully, this may help
preventing confusions against DRM_MODE_CONNECTOR_* and
DRM_MODE_ENCODER_*.
I guess that just by looking at the patch, some people will think this
change is not worth its benefits. In this case, I don't really mind
dropping the patch.
Also, there's probably still a few more places where we can
s/int/enum intel_output_type/, but we can change that later, when we
spot the places.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Resolve conflict due to reordered patches.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This will simplify things later on. No functional changes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Everything else can be derived from that. No functional changes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Most importantly, "i" need not be the universal variable used for
everything. No functional changes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Const is good.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In preparation for some additional cleanup. No functional changes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The fb check introduced to drm_plane_helper_check_update() just make this
check impossible to branch in.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
use_mmio_flip() makes sure we only enable MMIO flips on gen5+. So we
don't need to take into account older devices.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There is no point in flipping a buffer for a disabled crtc.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch includes the Gen9 batch buffer to generate
a 'golden context' for that product family.
Signed-off-by: Armin Reese <armin.c.reese@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The file drivers/gpu/drm/i915/intel_renderstate_gen8.c is
updated to the version created by IGT null_state_gen
Signed-off-by: Armin Reese <armin.c.reese@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
libva uses chained batch buffers in a way that the command parser
can't generally handle. Fortunately, libva doesn't need to write
registers from batch buffers in the way that mesa does, so this
patch causes the driver to fall back to non-secure dispatch if
the parser detects a chained batch buffer.
Note: The 2nd hunk to munge the error code of the parser looks a bit
superflous. At least until we have the batch copy code ready and can
run the cmd parser in granting mode. But it isn't since we still need
to let existing libva buffers pass (though not with elevated privs
ofc!).
Testcase: igt/gem_exec_parse/chained-batch
Signed-off-by: Brad Volkin <bradley.d.volkin@intel.com>
[danvet: Add note - this confused me in review and Brad clarified
things (after a few mails ...).]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This allows the cursor plane to be updated the same way as primary and sprites,
and same set_property handler is used for all of these planes.
v2 (by Matt Roper): Rework to apply to latest di-nightly codebase. The
switch to split check/commit plane programming changed the code
flow enough that the original patch could no longer be applied.
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Tested-by (IVB): Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If these flags are on the object level it will be more difficult to allow
for multiple VMAs per object.
v2: Simplification and cleanup after code review comments (Chris Wilson).
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
- suspend/resume/freeze/thaw unification from Imre
- wa list improvements from Mika&Arun
- display pll precomputation from Ander Conselvan, this removed the last
->mode_set callbacks, a big step towards implementing atomic modesets
- more kerneldoc for the interrupt code
- 180 rotation for cursors (Ville&Sonika)
- ULT/ULX feature check macros cleaned up thanks to Damien
- piles and piles of fixes all over, bug team seems to work!
* tag 'drm-intel-next-2014-10-24' of git://anongit.freedesktop.org/drm-intel: (61 commits)
drm/i915: Update DRIVER_DATE to 20141024
drm/i915: add comments on what stage a given PM handler is called
drm/i915: unify switcheroo and legacy suspend/resume handlers
drm/i915: add poweroff_late handler
drm/i915: sanitize suspend/resume helper function names
drm/i915: unify S3 and S4 suspend/resume handlers
drm/i915: disable/re-enable PCI device around S4 freeze/thaw
drm/i915: enable output polling during S4 thaw
drm/i915: check for GT faults in all resume handlers and driver load time
drm/i915: remove unused restore_gtt_mappings optimization during suspend
drm/i915: fix S4 suspend while switcheroo state is off
drm/i915: vlv: fix switcheroo/legacy suspend/resume
drm/i915: propagate error from legacy resume handler
drm/i915: unify legacy S3 suspend and S4 freeze handlers
drm/i915: factor out i915_drm_suspend_late
drm/i915: Emit even number of dwords when emitting LRIs
drm/i915: Add rotation support for cursor plane (v5)
drm/i915: Correctly reject invalid flags for wait_ioctl
drm/i915: use macros to assign mmio access functions
drm/i915: only run hsw_power_well_post_enable when really needed
...
When drm properties are created, they are added to mode_config.property_list,
which is then used in drm_mode_config_cleanup() to destroy every single
property created by the driver.
Cc: Chandra Konduru <chandra.konduru@intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ivybridge + 30" monitor prints a drm error on every modeset, since IVB
doesn't support DP3 we should even bother trying to use it.
This regression has been introduced in
commit 06ea66b6bb
Author: Todd Previte <tprevite@gmail.com>
Date: Mon Jan 20 10:19:39 2014 -0700
drm/i915: Enable 5.4Ghz (HBR2) link rate for Displayport 1.2-capable
devices
Reported-by: Dave Airlie <airlied@redhat.com>
Reference: http://mid.gmane.org/1414566170-9868-1-git-send-email-airlied@gmail.com
Cc: Todd Previte <tprevite@gmail.com>
Cc: stable@vger.kernel.org (3.15+)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
commit c675949ec5
Author: Jani Nikula <jani.nikula@intel.com>
Date: Wed Apr 9 11:31:37 2014 +0300
drm/i915: do not setup backlight if not available according to VBT
prevents backlight setup on Macbook 2,1. Apply quirk to ignore the VBT
check so backlight is set up properly.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=81438
Signed-off-by: Jens Stein Jørgensen <jens.s.stein@gmail.com>
Cc: stable@vger.kernel.org (3.15+)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Ok, new attempt, this time around with full ppgtt disabled again.
drm-intel-next-2014-10-03:
- first batch of skl stage 1 enabling
- fixes from Rodrigo to the PSR, fbc and sink crc code
- kerneldoc for the frontbuffer tracking code, runtime pm code and the basic
interrupt enable/disable functions
- smaller stuff all over
drm-intel-next-2014-09-19:
- bunch more i830M fixes from Ville
- full ppgtt now again enabled by default
- more ppgtt fixes from Michel Thierry and Chris Wilson
- plane config work from Gustavo Padovan
- spinlock clarifications
- piles of smaller improvements all over, as usual
* tag 'drm-intel-next-2014-10-03-no-ppgtt' of git://anongit.freedesktop.org/drm-intel: (114 commits)
Revert "drm/i915: Enable full PPGTT on gen7"
drm/i915: Update DRIVER_DATE to 20141003
drm/i915: Remove the duplicated logic between the two shrink phases
drm/i915: kerneldoc for interrupt enable/disable functions
drm/i915: Use dev_priv instead of dev in irq setup functions
drm/i915: s/pm._irqs_disabled/pm.irqs_enabled/
drm/i915: Clear TX FIFO reset master override bits on chv
drm/i915: Make sure hardware uses the correct swing margin/deemph bits on chv
drm/i915: make sink_crc return -EIO on aux read/write failure
drm/i915: Constify send buffer for intel_dp_aux_ch
drm/i915: De-magic the PSR AUX message
drm/i915: Reinstate error level message for non-simulated gpu hangs
drm/i915: Kerneldoc for intel_runtime_pm.c
drm/i915: Call runtime_pm_disable directly
drm/i915: Move intel_display_set_init_power to intel_runtime_pm.c
drm/i915: Bikeshed rpm functions name a bit.
drm/i915: Extract intel_runtime_pm.c
drm/i915: Remove intel_modeset_suspend_hw
drm/i915: spelling fixes for frontbuffer tracking kerneldoc
drm/i915: Tighting frontbuffer tracking around flips
...
vlv_cdclk_freq is in kHz but we need MHz for the GMBUSFREQ divider.
This is a regression from:
commit f8bf63fdcb
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Fri Jun 13 13:37:54 2014 +0300
drm/i915: Kill duplicated cdclk readout code from i2c
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Turning vdd on/off can generate a long hpd pulse on eDP ports. In order
to handle hpd we would need to turn on vdd to perform aux transfers.
This would lead to an endless cycle of
"vdd off -> long hpd -> vdd on -> detect -> vdd off -> ..."
So ignore long hpd pulses on eDP ports. eDP panels should be physically
tied to the machine anyway so they should not actually disappear and
thus don't need long hpd handling. Short hpds are still needed for link
re-train and whatnot so we can't just turn off the hpd interrupt
entirely for eDP ports. Perhaps we could turn it off whenever the panel
is disabled, but just ignoring the long hpd seems sufficient.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Dave Airlie <airlied@redhat.com>
Reviewed-by: Todd Previte <tprevite@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Sometimes we seem to get utter garbage from DPCD reads. The resulting
buffer is filled with the same byte, and the operation completed without
errors. My HP ZR24w monitor seems particularly susceptible to this
problem once it's gone into a sleep mode.
The issue seems to happen only for the first AUX message that wakes the
sink up. But as the first AUX read we often do is the DPCD receiver
cap it does wreak a bit of havoc with subsequent link training etc. when
the receiver cap bw/lane/etc. information is garbage.
A sufficient workaround seems to be to perform a single byte dummy read
before reading the actual data. I suppose that just wakes up the sink
sufficiently and we can just throw away the returned data in case it's
crap. DP_DPCD_REV seems like a sufficiently safe location to read here.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Todd Previte <tprevite@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
