The phylink conflict was between a bug fix by Russell King
to make sure we have a consistent PHY interface mode, and
a change in net-next to pull some code in phylink_resolve()
into the helper functions phylink_mac_link_{up,down}()
On the dp83867 side it's mostly overlapping changes, with
the 'net' side removing a condition that was supposed to
trigger for RGMII but because of how it was coded never
actually could trigger.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is a further step towards decoupling firmware handling from
the actual driver code. Firmware can be for PHY and/or MAC, and two
pairs of read/write functions are needed for handling PHY firmware and
MAC firmware respectively. Pass these functions via struct rtl_fw and
avoid the ugly switching of mdio_ops behind the back of rtl_writephy().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify the function a little bit and use strscpy() where appropriate.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call the pll power down function also for chip versions 02..06 and
13..15. The MAC can't be powered down on these chip versions, but at
least they benefit from the speed-down power-saving if WoL is enabled.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
(At least) RTL8168e forgets its MAC address in PCI D3. To fix this set
the MAC address when resuming. For resuming from runtime-suspend we
had this in place already, for resuming from S3/S5 it was missing.
The commit referenced as being fixed isn't wrong, it's just the first
one where the patch applies cleanly.
Fixes: 0f07bd850d ("r8169: use dev_get_drvdata where possible")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reported-by: Albert Astals Cid <aacid@kde.org>
Tested-by: Albert Astals Cid <aacid@kde.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
MAC on the GBit versions supports 1000/Full only, however the PHY
partially claims to support 1000/Half. So let's explicitly remove
this mode.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
RTL_GIGA_MAC_VER_01 is RTL8169, the ancestor of the chip family.
It didn't have an internal PHY and I've never seen it in the wild.
What isn't there doesn't need to be maintained, so let's remove
support for it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Certain parts of the PHY initialization are the same for sub versions
1 and 2 of RTL8168d. So let's factor this out to simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the appropriate enum type for member mac_version. And don't assign
a fixed value to RTL_GIGA_MAC_NONE, there's no benefit in it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rtl_hw_init_8168ep() can be removed, this simplifies the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all files which:
- Have no license information of any form
- Have MODULE_LICENCE("GPL*") inside which was used in the initial
scan/conversion to ignore the file
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on info from Realtek add a function for defining the thresholds
controlling ethernet flow control.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on info from Realtek replace FIFO size config magic with
a function.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move adjusting the EEE LED frequency to rtl8168_config_eee_mac.
Exclude RTL8411 (version 38) like in the existing code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make both functions macros to allow omitting the ARRAY_SIZE(x) argument.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When testing I figured out that most operations signal finish even
before we trigger the first delay. Seems like PCI(e) access and
memory barriers typically add enough latency. Therefore move the
first delay after the first check.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_probe() takes care that all supported modes are advertised,
in addition use phy_support_asym_pause() to advertise pause modes.
This way we don't have to deal with phylib internals directly.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rtl_write_exgmac_batch is used in only one place, so we can remove it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to Neil who reported the issue leading to this
workaround, the workaround is no longer needed since
version 5.0. So let's remove it.
This was the bug report leading to the workaround:
https://bugzilla.kernel.org/show_bug.cgi?id=201081
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Neil MacLeod <neil@nmacleod.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fortunately in one place there's a comment explaining what toggling
this bit does. So let's create a helper for it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add helpers rtl_eri_set_bits and rtl_eri_clear_bits to improve
readability of the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In basically all eri function calls the type argument is ERIAR_EXGMAC.
Therefore make it the default.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use new helper pci_dev_id() to simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: David S. Miller <davem@davemloft.net>
This check isn't really needed and we can simplify the code and save
some CPU cycles by removing it. Only in case of an error none of these
bits are set, and calling the NAPI callback doesn't hurt in this case.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using a function pointer array makes this easier to read and better
maintainable.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using a function pointer array makes this easier to read and better
maintainable. AFAIK function pointer arrays cause some performance
drawback due to Spectre mitigation, but we're not in a hot path here.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a significant number of reports that re-enabling ASPM causes
different issues, ranging from decreased performance to system not
booting at all. This affects only a minority of users, but the number
of affected users is big enough that we better switch off ASPM again.
This will hurt notebook users who are not affected by the issues, they
may see decreased battery runtime w/o ASPM. With the PCI core folks is
being discussed to add generic sysfs attributes to control ASPM.
Once this is in place brave enough users can re-enable ASPM on their
system.
Fixes: a99790bf5c ("r8169: Reinstate ASPM Support")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In contrast to switching rx irq coalescing off what fixed an issue,
switching tx irq coalescing off is merely a latency optimization,
therefore net-next. As part of this change:
- Remove INTT_0 .. INTT_3 constants, they aren't used.
- Remove comment in rtl_hw_start_8169(), we now have a detailed
description by the code in rtl_set_coalesce().
- Due to switching irq coalescing off per default we don't need the
initialization in rtl_hw_start_8168(). If ethtool is used to switch
on coalescing then rtl_set_coalesce() will configure this register.
For the sake of completeness: This patch just changes the default.
Users still have the option to configure irq coalescing via ethtool.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor comment merge conflict in mlx5.
Staging driver has a fixup due to the skb->xmit_more changes
in 'net-next', but was removed in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 6578229d4e.
netif_receive_skb_list() doesn't support GRO, therefore we may have
scenarios with decreased performance. See discussion here [0].
[0] https://marc.info/?t=155403847400001&r=1&w=2
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use netif_receive_skb_list() instead of napi_gro_receive() to benefit
from batched skb processing.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was reported that re-introducing ASPM, in combination with RX
interrupt coalescing, results in significantly increased packet
latency, see [0]. Disabling ASPM or RX interrupt coalescing fixes
the issue. Therefore change the driver's default to disable RX
interrupt coalescing. Users still have the option to enable RX
coalescing via ethtool.
[0] https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=925496
Fixes: a99790bf5c ("r8169: Reinstate ASPM Support")
Reported-by: Mike Crowe <mac@mcrowe.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bartek reported that after few cable unplug/replug cycles suddenly
replug isn't detected any longer. His system uses a RTL8106, I wasn't
able to reproduce the issue with RTL8168g. According to his bisect
the referenced commit caused the regression. As Realtek doesn't
release datasheets or errata it's hard to say what's the actual root
cause, but this change was reported to fix the issue.
Fixes: 38caff5a44 ("r8169: handle all interrupt events in the hard irq handler")
Reported-by: Bartosz Skrzypczak <barteks2x@gmail.com>
Suggested-by: Bartosz Skrzypczak <barteks2x@gmail.com>
Tested-by: Bartosz Skrzypczak <barteks2x@gmail.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the call to netif_wake_queue in rtl8169_start_xmit with
netif_start_queue as we don't need to actually wake up the queue since
we are still in mid transmit so we just need to reset the bit so it
doesn't prevent the next transmit.
(Description shamelessly copied from a mail sent by Alex.)
Suggested-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the original patch network starts to crash on heavy load.
It's not fully clear why this additional register read has such side
effects, but removing it fixes the issue.
Thanks also to Alex for his contribution and hints.
[0] https://marc.info/?t=155268170400002&r=1&w=2
Fixes: e782410ed2 ("r8169: improve spurious interrupt detection")
Reported-by: VDR User <user.vdr@gmail.com>
Tested-by: VDR User <user.vdr@gmail.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a statement that is indented incorrectly; replace
spaces with a tab.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add PCI vendor and device identifier for U.S. Robotics USR997901A
10/100 Cardbus NIC. Tested on real hardware.
Signed-off-by: Matthew Whitehead <tedheadster@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
writex() has implicit barriers, that's what makes it different from
writex_relaxed(). Therefore these calls to mmiowb() can be removed.
This patch was recently reverted due to a dependency with another
problematic patch. But because it didn't contribute to the problem
it was rebased and can be resubmitted.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netfilter conflicts were rather simple overlapping
changes.
However, the cls_tcindex.c stuff was a bit more complex.
On the 'net' side, Cong is fixing several races and memory
leaks. Whilst on the 'net-next' side we have Vlad adding
the rtnl-ness support.
What I've decided to do, in order to resolve this, is revert the
conversion over to using a workqueue that Cong did, bringing us back
to pure RCU. I did it this way because I believe that either Cong's
races don't apply with have Vlad did things, or Cong will have to
implement the race fix slightly differently.
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 2e6eedb481.
Sander reported a regression causing a kernel panic[1],
therefore let's revert this commit.
[1] https://marc.info/?t=154965066400001&r=1&w=2
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit bd7153bd83.
There doesn't seem to be anything wrong with this patch,
it's just reverted to get a stable baseline again.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Read MAC address 32-bit at a time and manually extract the individual
bytes. This avoids pointer aliasing and gives the compiler a better
chance of optimizing the operation.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the system was booted using a device tree and if the device tree
contains a MAC address, use it instead of reading one from the EEPROM.
This is useful in situations where the EEPROM isn't properly programmed
or where the firmware wants to override the existing MAC address.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
rtl_wol_pll_power_down() is used in only one place and removing it
makes the code simpler and better readable.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
WoL handling for the RTL8168 family is a little bit tricky because of
different types of broken BIOS and/or chip quirks.
Two known issues:
1. Network properly resumes from suspend only if WoL is enabled in the chip.
2. Some notebooks wake up immediately if system is suspended and network
device is wakeup-enabled.
Few patches tried to deal with this:
7edf6d314c ("r8169: disable WOL per default")
18041b5236 ("r8169: restore previous behavior to accept BIOS WoL
settings")
Currently we have the situation that the chip WoL settings as set by
the BIOS are respected (to prevent issue 1), but the device doesn't get
wakeup-enabled (to prevent issue 2).
This leads to another issue:
If systemd is told to set WoL it first checks whether the requested
settings are active already (and does nothing if yes). Due to the chip
WoL flags being set properly systemd assumes that WoL is configured
properly in our case. Result is that device doesn't get wakeup-enabled
and WoL doesn't work (until it's set e.g. by ethtool).
This patch now:
- leaves the chip WoL settings as is (to prevent issue 1)
- keeps the behavior to not wakeup-enable the device initially
(to prevent issue 2)
- In addition we report WoL as being disabled in get_wol, matching
that device isn't wakeup-enabled. If systemd is told to enable WoL,
it will therefore detect that it has to do something and will
call set_wol.
Of course the user still has the option to override this with
e.g. ethtool.
v2:
- Don't just exclude __rtl8169_get_wol() from compiling, remove it.
v3:
- adjust commit message
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_consume_skb_irq() should be called in cp_tx() when skb xmit
done. It makes drop profiles(dropwatch, perf) more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add EEE support for RTL8168f to the recently added EEE handling
framework in the driver. This patch leaves the chip defaults, means
EEE typically is disabled initially and it's up to the user to enable
it via ethtool.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable EEE per default on chip versions from RTL8168g.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the general framework to deal with EEE in this driver
plus EEE support for chip versions from RTL8168g. We don't touch the
default chip settings, therefore EEE will usually be disabled and it's
up to the user to enable it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Few chip versions use the same sequence to adjust 10M and ALDPS, so
let's factor it out. This patch also fixes a (most likely) typo in
rtl8168g_1_hw_phy_config. There bit 8 in reg 0x14 on page 0x0bcc
was set and not cleared. According to the vendor driver this bit
needs to be cleared in all cases.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chip versions from RTL8168g onward use the same sequence to disable
ALDPS (Advanced Link-Down Power Saving). So let's factor this out.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far member rtl_fw has three states:
- IS_ERR(rtl_fw): firmware not loaded
- !rtl_fw: no firmware available
- other: firmware loaded
This can be made simpler and clearer by adding the firmware name as
member fw_name to struct rtl8169_private. Then:
- !fw_name: no firmware available
- !rtl_fw: firmware not loaded
- rtl_fw: firmware loaded
This change also allows to easily merge rtl_request_uncached_firmware
into rtl_request_firmware.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The old non-PCIe chip versions support PCI DAC, however this feature
seems to be fragile, see comment in the PCI error handler. Therefore
it's disabled per default. I think meanwhile it's time remove support
for this legacy feature. This helps to reduce complexity of the driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years ago, as part of 6f0333b8fd ("r8169: use 50% less ram for RX
ring"), the alignment requirement for rx buffers was silently changed
from 8 bytes to 16 bytes. I found nothing explaining this, also the
chip specs I have only mention an 8 byte requirement.
AFAICS kmalloc_node() guarantees allocated memory to be at least
"long long" aligned, what is 8 bytes on a 32 bit machine.
So we can take this memory as-is and avoid some overhead by changing
the alignment requirement back to 8 bytes.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rtl_init_one() is complex enough, so we better factor out getting the
ether_clk.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Accessing the phy_device indirectly via the netdevice causes few issues:
- Accessing the phy_device when it's not attached may cause a NPE.
- If we have to access the phy_device when it's not attached we have
to use mdiobus_get_phy() to get a reference to the phy_device.
Therefore store a phy_device reference in struct rtl8169_private directly.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Triggering an asynchronous reset is problematic for the following
reasons, therefore reset the chip synchronously.
- The reset routine resets registers and parameters behind our back
what may collide with code executed after triggering the reset.
- __rtl8169_resume() is called as part of pm_runtime_get_sync() and
callers expect that the chip is fully resumed afterwards.
In context of this driver triggering an asynchonous reset should be
considered an emergency procedure.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add helpers for locking / unlocking the config registers.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All calls to this function have the enable parameter set to false.
So we can replace the function with a disable-only version.
v2:
- fixed copy & paste error
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's sufficient to initialize the workqueue once, therefore remove the
additional initialization whenever rtl_open() is called.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rtl8169_hw_reset() is called as part of the reset routine which is
scheduled in the line after. So we can remove the call to
rtl8169_hw_reset() here.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This helper is used only once, so remove it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are various lines that have indentation issues, fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This soft dependency works around an issue where sometimes the genphy
driver is used instead of the dedicated PHY driver. The root cause of
the issue isn't clear yet. People reported the unloading/re-loading
module r8169 helps, and also configuring this soft dependency in
the modprobe config files. Important just seems to be that the
realtek module is loaded before r8169.
Once this has been applied preliminary fix 38af4b903210 ("net: phy:
add workaround for issue where PHY driver doesn't bind to the device")
will be removed.
Fixes: f1e911d5d0 ("r8169: add basic phylib support")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid log spam caused by trying to read counters from the chip whilst
it is in a PCI power-save state.
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=107421
Fixes: 1ef7286e7f ("r8169: Dereference MMIO address immediately before use")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two new Realtek Ethernet devices which are re-branded r8168h.
Add the IDs to to support them.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In rtl8169_runtime_resume() we configure WoL but don't set the device
to wakeup-enabled. This prevents PME generation once the cable is
re-plugged. Fix this by moving the call to device_set_wakeup_enable()
to __rtl8169_set_wol().
Fixes: 433f9d0ddc ("r8169: improve saved_wolopts handling")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) New ipset extensions for matching on destination MAC addresses, from
Stefano Brivio.
2) Add ipv4 ttl and tos, plus ipv6 flow label and hop limit offloads to
nfp driver. From Stefano Brivio.
3) Implement GRO for plain UDP sockets, from Paolo Abeni.
4) Lots of work from Michał Mirosław to eliminate the VLAN_TAG_PRESENT
bit so that we could support the entire vlan_tci value.
5) Rework the IPSEC policy lookups to better optimize more usecases,
from Florian Westphal.
6) Infrastructure changes eliminating direct manipulation of SKB lists
wherever possible, and to always use the appropriate SKB list
helpers. This work is still ongoing...
7) Lots of PHY driver and state machine improvements and
simplifications, from Heiner Kallweit.
8) Various TSO deferral refinements, from Eric Dumazet.
9) Add ntuple filter support to aquantia driver, from Dmitry Bogdanov.
10) Batch dropping of XDP packets in tuntap, from Jason Wang.
11) Lots of cleanups and improvements to the r8169 driver from Heiner
Kallweit, including support for ->xmit_more. This driver has been
getting some much needed love since he started working on it.
12) Lots of new forwarding selftests from Petr Machata.
13) Enable VXLAN learning in mlxsw driver, from Ido Schimmel.
14) Packed ring support for virtio, from Tiwei Bie.
15) Add new Aquantia AQtion USB driver, from Dmitry Bezrukov.
16) Add XDP support to dpaa2-eth driver, from Ioana Ciocoi Radulescu.
17) Implement coalescing on TCP backlog queue, from Eric Dumazet.
18) Implement carrier change in tun driver, from Nicolas Dichtel.
19) Support msg_zerocopy in UDP, from Willem de Bruijn.
20) Significantly improve garbage collection of neighbor objects when
the table has many PERMANENT entries, from David Ahern.
21) Remove egdev usage from nfp and mlx5, and remove the facility
completely from the tree as it no longer has any users. From Oz
Shlomo and others.
22) Add a NETDEV_PRE_CHANGEADDR so that drivers can veto the change and
therefore abort the operation before the commit phase (which is the
NETDEV_CHANGEADDR event). From Petr Machata.
23) Add indirect call wrappers to avoid retpoline overhead, and use them
in the GRO code paths. From Paolo Abeni.
24) Add support for netlink FDB get operations, from Roopa Prabhu.
25) Support bloom filter in mlxsw driver, from Nir Dotan.
26) Add SKB extension infrastructure. This consolidates the handling of
the auxiliary SKB data used by IPSEC and bridge netfilter, and is
designed to support the needs to MPTCP which could be integrated in
the future.
27) Lots of XDP TX optimizations in mlx5 from Tariq Toukan.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1845 commits)
net: dccp: fix kernel crash on module load
drivers/net: appletalk/cops: remove redundant if statement and mask
bnx2x: Fix NULL pointer dereference in bnx2x_del_all_vlans() on some hw
net/net_namespace: Check the return value of register_pernet_subsys()
net/netlink_compat: Fix a missing check of nla_parse_nested
ieee802154: lowpan_header_create check must check daddr
net/mlx4_core: drop useless LIST_HEAD
mlxsw: spectrum: drop useless LIST_HEAD
net/mlx5e: drop useless LIST_HEAD
iptunnel: Set tun_flags in the iptunnel_metadata_reply from src
net/mlx5e: fix semicolon.cocci warnings
staging: octeon: fix build failure with XFRM enabled
net: Revert recent Spectre-v1 patches.
can: af_can: Fix Spectre v1 vulnerability
packet: validate address length if non-zero
nfc: af_nfc: Fix Spectre v1 vulnerability
phonet: af_phonet: Fix Spectre v1 vulnerability
net: core: Fix Spectre v1 vulnerability
net: minor cleanup in skb_ext_add()
net: drop the unused helper skb_ext_get()
...
Pull RCU updates from Ingo Molnar:
"The biggest RCU changes in this cycle were:
- Convert RCU's BUG_ON() and similar calls to WARN_ON() and similar.
- Replace calls of RCU-bh and RCU-sched update-side functions to
their vanilla RCU counterparts. This series is a step towards
complete removal of the RCU-bh and RCU-sched update-side functions.
( Note that some of these conversions are going upstream via their
respective maintainers. )
- Documentation updates, including a number of flavor-consolidation
updates from Joel Fernandes.
- Miscellaneous fixes.
- Automate generation of the initrd filesystem used for rcutorture
testing.
- Convert spin_is_locked() assertions to instead use lockdep.
( Note that some of these conversions are going upstream via their
respective maintainers. )
- SRCU updates, especially including a fix from Dennis Krein for a
bag-on-head-class bug.
- RCU torture-test updates"
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (112 commits)
rcutorture: Don't do busted forward-progress testing
rcutorture: Use 100ms buckets for forward-progress callback histograms
rcutorture: Recover from OOM during forward-progress tests
rcutorture: Print forward-progress test age upon failure
rcutorture: Print time since GP end upon forward-progress failure
rcutorture: Print histogram of CB invocation at OOM time
rcutorture: Print GP age upon forward-progress failure
rcu: Print per-CPU callback counts for forward-progress failures
rcu: Account for nocb-CPU callback counts in RCU CPU stall warnings
rcutorture: Dump grace-period diagnostics upon forward-progress OOM
rcutorture: Prepare for asynchronous access to rcu_fwd_startat
torture: Remove unnecessary "ret" variables
rcutorture: Affinity forward-progress test to avoid housekeeping CPUs
rcutorture: Break up too-long rcu_torture_fwd_prog() function
rcutorture: Remove cbflood facility
torture: Bring any extra CPUs online during kernel startup
rcutorture: Add call_rcu() flooding forward-progress tests
rcutorture/formal: Replace synchronize_sched() with synchronize_rcu()
tools/kernel.h: Replace synchronize_sched() with synchronize_rcu()
net/decnet: Replace rcu_barrier_bh() with rcu_barrier()
...
Lots of conflicts, by happily all cases of overlapping
changes, parallel adds, things of that nature.
Thanks to Stephen Rothwell, Saeed Mahameed, and others
for their guidance in these resolutions.
Signed-off-by: David S. Miller <davem@davemloft.net>
Improve detection of spurious interrupts by checking against the
interrupt mask as currently set in the chip.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If CONFIG_DEBUG_SHIRQ is enabled __free_irq() intentionally fires
a spurious interrupt. This interrupt causes a crash because
tp->dev->phydev is NULL at that time.
Fixes: 38caff5a44 ("r8169: handle all interrupt events in the hard irq handler")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several conflicts, seemingly all over the place.
I used Stephen Rothwell's sample resolutions for many of these, if not
just to double check my own work, so definitely the credit largely
goes to him.
The NFP conflict consisted of a bug fix (moving operations
past the rhashtable operation) while chaning the initial
argument in the function call in the moved code.
The net/dsa/master.c conflict had to do with a bug fix intermixing of
making dsa_master_set_mtu() static with the fixing of the tagging
attribute location.
cls_flower had a conflict because the dup reject fix from Or
overlapped with the addition of port range classifiction.
__set_phy_supported()'s conflict was relatively easy to resolve
because Andrew fixed it in both trees, so it was just a matter
of taking the net-next copy. Or at least I think it was :-)
Joe Stringer's fix to the handling of netns id 0 in bpf_sk_lookup()
intermixed with changes on how the sdif and caller_net are calculated
in these code paths in net-next.
The remaining BPF conflicts were largely about the addition of the
__bpf_md_ptr stuff in 'net' overlapping with adjustments and additions
to the relevant data structure where the MD pointer macros are used.
Signed-off-by: David S. Miller <davem@davemloft.net>
writex() has implicit barriers, that's what makes it different from
writex_relaxed(). Therefore these calls to mmiowb() can be removed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that synchronize_rcu() waits for preempt-disable regions of code
as well as RCU read-side critical sections, synchronize_sched() can be
replaced by synchronize_rcu(). This commit therefore makes this change.
Signed-off-by: Paul E. McKenney <paulmck@linux.ibm.com>
Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: <netdev@vger.kernel.org>
Make use of xmit_more and add the functionality introduced with
3e59020abf ("net: bql: add __netdev_tx_sent_queue()").
I used the mlx4 driver as template.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace macro TX_FRAGS_READY_FOR with function rtl_tx_slots_avail
to make code cleaner and type-safe.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use napi_consume_skb() where possible to profit from
bulk free infrastructure.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the GMII chip versions we set the version number which was set
already. This can be simplified.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even the chip versions within a family have so many differences that
using a default chip version doesn't really make sense. Instead
of leaving a best case flaky network connectivity, bail out and
report the unknown chip version.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove ancient GCC bug workaround in a second place and factor out
rtl_8169_get_txd_opts1.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only the upper 12 bits are used for chip identification, this helps
to reduce the size of array mac_info.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rtl8168_oob_notify is used in rtl8168dp_driver_start and
rtl8168dp_driver_stop only, so we can rename it to r8168dp_oob_notify.
The same applies to condition rtl_ocp_read_cond which can be renamed
to rtl_dp_ocp_read_cond. This allows to simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kernel can't be built any longer with this ancient GCC version.
Eventually it becomes clear what this statement actually does.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The compiler takes care of alignment and padding, I see no need to
bother him with manual hints.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ones who want to know can easily identify whether chip is PCI or
PCIe based on the chip name. I doubt there's any benefit in this
message, so remove it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The syslog message printed on driver load allows to easily identify
the mac version number (based on chip name and XID). So we don't
need this extra debug message which is wrong anyway because e.g.
RTL_GIGA_MAC_VER_01 has value 0.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using macro PCI_VDEVICE helps to simplify the PCI ID table.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently the "slow event" handler was removed, therefore the member
name isn't appropriate any longer. In addition store the full mask,
including the RTL_EVENT_NAPI interrupt source bits.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting PCSTimeout interrupt source was copied from the vendor driver
which uses the chip programmable timer interrupt. The mainline driver
doesn't use this timer interrupt.
SYSErr indicates a PCI error and isn't defined on the PCIe models.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using dev_get_drvdata directly is simpler here.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the recent changes to the interrupt handler rtl_irq_enable and
rtl_irq_enable_all can be merged.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PCI vendor id of U.S. Robotics isn't defined in pci_ids.h so far,
only ISDN driver w6692 has a private definition. Move the definition
to pci_ids.h and use it in the r8169 driver too.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a few MAC/PHYs combinations which now support > 1Gbps. These
may need to make use of link modes with bits > 31. Thus their
supported PHY features or advertised features cannot be implemented
using the current bitmap in a u32. Convert to using a linkmode bitmap,
which can support all the currently devices link modes, and is future
proof as more modes are added.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was reported that WoL from S5 is broken (WoL from S3 works) and the
analysis showed that during system shutdown the network interface was
brought down already when the actual kernel shutdown started.
Therefore netif_running() returned false and as a consequence the PHY
was suspended. Obviously WoL wasn't working then.
To fix this the original patch needs to be effectively reverted.
A side effect is that when normally bringing down the interface and
WoL is enabled the PHY will remain powered on (like it was before the
original patch).
Fixes: fe87bef01f ("r8169: don't check WoL when powering down PHY and interface is down")
Reported-by: Neil MacLeod <neil@nmacleod.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is basically a resubmit of 1e91887685 ("r8169: add support
for Byte Queue Limits") which was reverted later. The problems causing
the revert seem to have been fixed in the meantime.
Only change to the original patch is that the call to
netdev_reset_queue was moved to rtl8169_tx_clear.
The Tested-by refers to a system using the RTL8168evl chip version.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Holger Hoffstätte <holger@applied-asynchrony.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Having a separate "slow event" handler isn't needed because all
interrupt events trigger asynchronous activity. And in case of SYSErr
we have bigger problems than performance anyway.
This patch also allows to get rid of acking interrupt events in the
NAPI poll callback.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/sched/cls_api.c has overlapping changes to a call to
nlmsg_parse(), one (from 'net') added rtm_tca_policy instead of NULL
to the 5th argument, and another (from 'net-next') added cb->extack
instead of NULL to the 6th argument.
net/ipv4/ipmr_base.c is a case of a bug fix in 'net' being done to
code which moved (to mr_table_dump)) in 'net-next'. Thanks to David
Ahern for the heads up.
Signed-off-by: David S. Miller <davem@davemloft.net>
rtl_rx() and rtl_tx() are called only if the respective bits are set
in the interrupt status register. Under high load NAPI may not be
able to process all data (work_done == budget) and it will schedule
subsequent calls to the poll callback.
rtl_ack_events() however resets the bits in the interrupt status
register, therefore subsequent calls to rtl8169_poll() won't call
rtl_rx() and rtl_tx() - chip interrupts are still disabled.
Fix this by calling rtl_rx() and rtl_tx() independent of the bits
set in the interrupt status register. Both functions will detect
if there's nothing to do for them.
Fixes: da78dbff2e ("r8169: remove work from irq handler.")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to d49c88d767 ("r8169: Enable MSI-X on RTL8106e") after
e9d0ba506ea8 ("PCI: Reprogram bridge prefetch registers on resume")
we can safely assume that this also fixes the root cause of
the issue worked around by 7c53a72245 ("r8169: don't use MSI-X on
RTL8168g"). So let's revert it.
Fixes: 7c53a72245 ("r8169: don't use MSI-X on RTL8168g")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netif_device_detach() stops all tx queues already, so we don't need
this call.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify this function, no functional change intended.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Originally, we have an issue where r8169 MSI-X interrupt is broken after
S3 suspend/resume on RTL8106e of ASUS X441UAR.
02:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd.
RTL8101/2/6E PCI Express Fast/Gigabit Ethernet controller [10ec:8136]
(rev 07)
Subsystem: ASUSTeK Computer Inc. RTL810xE PCI Express Fast
Ethernet controller [1043:200f]
Flags: bus master, fast devsel, latency 0, IRQ 16
I/O ports at e000 [size=256]
Memory at ef100000 (64-bit, non-prefetchable) [size=4K]
Memory at e0000000 (64-bit, prefetchable) [size=16K]
Capabilities: [40] Power Management version 3
Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+
Capabilities: [70] Express Endpoint, MSI 01
Capabilities: [b0] MSI-X: Enable+ Count=4 Masked-
Capabilities: [d0] Vital Product Data
Capabilities: [100] Advanced Error Reporting
Capabilities: [140] Virtual Channel
Capabilities: [160] Device Serial Number 01-00-00-00-36-4c-e0-00
Capabilities: [170] Latency Tolerance Reporting
Kernel driver in use: r8169
Kernel modules: r8169
We found the all of the values in PCI BAR=4 of the ethernet adapter
become 0xFF after system resumes. That breaks the MSI-X interrupt.
Therefore, we can only fall back to MSI interrupt to fix the issue at
that time.
However, there is a commit which resolves the drivers getting nothing in
PCI BAR=4 after system resumes. It is 04cb3ae895d7 "PCI: Reprogram
bridge prefetch registers on resume" by Daniel Drake.
After apply the patch, the ethernet adapter works fine before suspend
and after resume. So, we can revert the workaround after the commit
"PCI: Reprogram bridge prefetch registers on resume" is merged into main
tree.
This patch reverts commit 7bb05b85bc
"r8169: don't use MSI-X on RTL8106e".
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=201181
Fixes: 7bb05b85bc ("r8169: don't use MSI-X on RTL8106e")
Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts were easy to resolve using immediate context mostly,
except the cls_u32.c one where I simply too the entire HEAD
chunk.
Signed-off-by: David S. Miller <davem@davemloft.net>
It has been reported that since
commit 05212ba813 ("r8169: set RxConfig after tx/rx is enabled for RTL8169sb/8110sb devices")
at least RTL_GIGA_MAC_VER_38 NICs work erratically after a resume from
suspend.
The problem has been traced to a missing RX_MULTI_EN bit in the RxConfig
register.
We already set this bit for RTL_GIGA_MAC_VER_35 NICs of the same 8168F
chip family so let's do it also for its other siblings: RTL_GIGA_MAC_VER_36
and RTL_GIGA_MAC_VER_38.
Curiously, the NIC seems to work fine after a system boot without having
this bit set as long as the system isn't suspended and resumed.
Fixes: 05212ba813 ("r8169: set RxConfig after tx/rx is enabled for RTL8169sb/8110sb devices")
Reported-by: Chris Clayton <chris2553@googlemail.com>
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Chris Clayton <chris2553@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor conflict in net/core/rtnetlink.c, David Ahern's bug fix in 'net'
overlapped the renaming of a netlink attribute in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
This affects at least versions 25 and 33, so assume all cards are broken
and just renegotiate by default.
Fixes: 10bc6a6042 ("r8169: fix autoneg issue on resume with RTL8168E")
Signed-off-by: Alex Xu (Hello71) <alex_y_xu@yahoo.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the chip-specific hw_start functions set bit TXCFG_AUTO_FIFO
in register TxConfig. The original patch changed the order of some
calls resulting in these changes being overwritten by
rtl_set_tx_config_registers() in rtl_hw_start(). This eventually
resulted in network stalls especially under high load.
Analyzing the chip-specific hw_start functions all chip version from
34, with the exception of version 39, need this bit set.
This patch moves setting this bit to rtl_set_tx_config_registers().
Fixes: 4fd48c4ac0 ("r8169: move common initializations to tp->hw_start")
Reported-by: Ortwin Glück <odi@odi.ch>
Reported-by: David Arendt <admin@prnet.org>
Root-caused-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Tested-by: Tony Atkinson <tatkinson@linux.com>
Tested-by: David Arendt <admin@prnet.org>
Tested-by: Ortwin Glück <odi@odi.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disable the clk during suspend to save power. Note that tp->clk may be
NULL, the clk core functions handle this without problems.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Version bump conflict in batman-adv, take what's in net-next.
iavf conflict, adjustment of netdev_ops in net-next conflicting
with poll controller method removal in net.
Signed-off-by: David S. Miller <davem@davemloft.net>
The check for pci_is_pcie() is redundant here because all
chip versions >=18 are PCIe only anyway. In addition use
dma_set_mask_and_coherent() instead of separate calls to
pci_set_dma_mask() and pci_set_consistent_dma_mask().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Code can be slightly simplified by acking even events we're not
interested in. In addition add a comment making clear that the
read has no functional purpose and is just a PCI commit.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The networking core has a default watchdog timeout of 5s. I see no
need to define an own timeout of 6s which is basically the same.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was reported that chip version 33 (RTL8168E) ends up with
10MBit/Half on a 1GBit link after resuming from S3 (with different
link partners). For whatever reason the PHY on this chip doesn't
properly start a renegotiation when soft-reset.
Explicitly requesting a renegotiation fixes this.
Fixes: a2965f12fd ("r8169: remove rtl8169_set_speed_xmii")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reported-by: Neil MacLeod <neil@nmacleod.com>
Tested-by: Neil MacLeod <neil@nmacleod.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting register 0x82 to value 01 is done a few lines before for all
chip versions <= 06 anyway. And setting PHY register 0x0b to value 00
is done at the end of rtl8169s_hw_phy_config() already. So we can
remove this.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PCI_LATENCY_TIMER is ignored on PCIe, therefore we have to do this
for the PCI chips (version <= 06) only. Also we can move setting
PCI_CACHE_LINE_SIZE.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some boards a platform clock is used as clock for the r8169 chip,
this commit adds support for getting and enabling this clock (assuming
it has an "ether_clk" alias set on it).
This is related to commit d31fd43c0f ("clk: x86: Do not gate clocks
enabled by the firmware") which is a previous attempt to fix this for some
x86 boards, but this causes all Cherry Trail SoC using boards to not reach
there lowest power states when suspending.
This commit (together with an atom-pmc-clk driver commit adding the alias)
fixes things properly by making the r8169 get the clock and enable it when
it needs it.
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=193891#c102
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=196861
Cc: Johannes Stezenbach <js@sig21.net>
Cc: Carlo Caione <carlo@endlessm.com>
Reported-by: Johannes Stezenbach <js@sig21.net>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Intel SoC was prevented from entering lower idle state because
of RTL8106E's ASPM was not enabled.
So enable ASPM on RTL8106E (chip version 39).
Now the Intel SoC can enter lower idle state, power consumption and
temperature are much lower.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a small delay after setting ASPM in vendor drivers, r8101 and
r8168.
In addition, those drivers enable ASPM before ClkReq, also change that
to align with vendor driver.
I haven't seen anything bad becasue of this, but I think it's better to
keep in sync with vendor driver.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After system suspend, sometimes the r8169 doesn't work when ethernet
cable gets pluggued.
This issue happens because rtl_reset_work() doesn't get called from
rtl8169_runtime_resume(), after system suspend.
In rtl_task(), RTL_FLAG_TASK_* only gets cleared if this condition is
met:
if (!netif_running(dev) ||
!test_bit(RTL_FLAG_TASK_ENABLED, tp->wk.flags))
...
If RTL_FLAG_TASK_ENABLED was cleared during system suspend while
RTL_FLAG_TASK_RESET_PENDING was set, the next rtl_schedule_task() won't
schedule task as the flag is still there.
So in addition to clearing RTL_FLAG_TASK_ENABLED, also clears other
flags.
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 3559d81e76 ("r8169: simplify rtl_hw_start_8169") changed order of
two register writes:
1) Caused RxConfig to be written before TX / RX is enabled,
2) Caused TxConfig to be written before TX / RX is enabled.
At least on XIDs 10000000 ("RTL8169sb/8110sb") and
18000000 ("RTL8169sc/8110sc") such writes are ignored by the chip, leaving
values in these registers intact.
Change 1) was reverted by
commit 05212ba813 ("r8169: set RxConfig after tx/rx is enabled for RTL8169sb/8110sb devices"),
however change 2) wasn't.
In practice, this caused TxConfig's "InterFrameGap time" and "Max DMA Burst
Size per Tx DMA Burst" bits to be zero dramatically reducing TX performance
(in my tests it dropped from around 500Mbps to around 50Mbps).
This patch fixes the issue by moving TxConfig register write a bit later in
the code so it happens after TX / RX is already enabled.
Fixes: 05212ba813 ("r8169: set RxConfig after tx/rx is enabled for RTL8169sb/8110sb devices")
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: David S. Miller <davem@davemloft.net>
This card identifies itself as:
Ethernet controller [0200]: NCube Device [10ff:8168] (rev 06)
Subsystem: TP-LINK Technologies Co., Ltd. Device [7470:3468]
Adding a new entry to rtl8169_pci_tbl makes the card work.
Link: http://launchpad.net/bugs/1788730
Signed-off-by: Anthony Wong <anthony.wong@ubuntu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I have two Ethernet adapters:
r8169 0000:03:01.0 eth0: RTL8169sb/8110sb, 00:14:d1:14:2d:49, XID 10000000, IRQ 18
r8169 0000:01:00.0 eth0: RTL8168e/8111e, 64:66:b3:11:14:5d, XID 2c200000, IRQ 30
And after upgrading from linux 4.15 [1] to linux 4.18+ [2] RTL8169sb failed to
receive any packets. tcpdump shows a lot of checksum mismatch.
[1]: a0f79386a4
[2]: 0519359784 (4.19 merge window opened)
I started bisecting and the found that [3] breaks it. According to [4]:
"For 8110S, 8110SB, and 8110SC series, the initial value of RxConfig
needs to be set after the tx/rx is enabled."
So I moved rtl_init_rxcfg() after enabling tx/rs and now my adapter works
(RTL8168e works too).
[3]: 3559d81e76
[4]: e542a2269f ("r8169: adjust the RxConfig
settings.")
Also drop "rx" from rtl_set_rx_tx_config_registers(), since it does nothing
with it already.
Fixes: 3559d81e76 ("r8169: simplify
rtl_hw_start_8169")
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>
Signed-off-by: Azat Khuzhin <a3at.mail@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Found the ethernet network on ASUS X441UAR doesn't come back on resume
from suspend when using MSI-X. The chip is RTL8106e - version 39.
[ 21.848357] libphy: r8169: probed
[ 21.848473] r8169 0000:02:00.0 eth0: RTL8106e, 0c:9d:92:32:67:b4, XID
44900000, IRQ 127
[ 22.518860] r8169 0000:02:00.0 enp2s0: renamed from eth0
[ 29.458041] Generic PHY r8169-200:00: attached PHY driver [Generic
PHY] (mii_bus:phy_addr=r8169-200:00, irq=IGNORE)
[ 63.227398] r8169 0000:02:00.0 enp2s0: Link is Up - 100Mbps/Full -
flow control off
[ 124.514648] Generic PHY r8169-200:00: attached PHY driver [Generic
PHY] (mii_bus:phy_addr=r8169-200:00, irq=IGNORE)
Here is the ethernet controller in detail:
02:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd.
RTL8101/2/6E PCI Express Fast/Gigabit Ethernet controller [10ec:8136]
(rev 07)
Subsystem: ASUSTeK Computer Inc. RTL810xE PCI Express Fast
Ethernet controller [1043:200f]
Flags: bus master, fast devsel, latency 0, IRQ 16
I/O ports at e000 [size=256]
Memory at ef100000 (64-bit, non-prefetchable) [size=4K]
Memory at e0000000 (64-bit, prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: r8169
Kernel modules: r8169
Falling back to MSI fixes the issue.
Fixes: 6c6aa15fde ("r8169: improve interrupt handling")
Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we switched the r8169 driver to use phylib, there's a
dependency on the Realtek PHY drivers. This dependency was missing
in Kconfig.
Reported-by: Jouni Mettälä <jtmettala@gmail.com>
Fixes: f1e911d5d0 ("r8169: add basic phylib support")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There have been two reports that network doesn't come back on resume
from suspend when using MSI-X. Both cases affect the same chip version
(RTL8168g - version 40), on different systems. Falling back to MSI
fixes the issue.
Even though we don't really have a proof yet that the network chip
version is to blame, let's disable MSI-X for this version.
Reported-by: Steve Dodd <steved424@gmail.com>
Reported-by: Lou Reed <gogen@disroot.org>
Tested-by: Steve Dodd <steved424@gmail.com>
Tested-by: Lou Reed <gogen@disroot.org>
Fixes: 6c6aa15fde ("r8169: improve interrupt handling")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't have to configure the max jumbo frame size per chip
(sub-)version. It can be easily determined based on the chip family.
And new members of the RTL8168 family (if there are any) should be
automatically covered.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't have to configure the csum function per chip (sub-)version.
The distinction is simple, versions RTL8102e and from RTL8168c onwards
support csum_v2.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify the interrupt handler a little and make it better readable.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The asm headers shouldn't be included directly. asm/irq.h is
implicitly included by linux/interrupt.h, and instead of
asm/io.h include linux/io.h.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The version number hasn't changed for ages and in general I doubt it
provides any benefit. The message in rtl_init_one() may even be
misleading because it's printed also if something fails in probe.
Therefore let's remove the version information.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 7edf6d314c tried to resolve an inconsistency (BIOS WoL
settings are accepted, but device isn't wakeup-enabled) resulting
from a previous broken-BIOS workaround by making disabled WoL the
default.
This however had some side effects, most likely due to a broken BIOS
some systems don't properly resume from suspend when the MagicPacket
WoL bit isn't set in the chip, see
https://bugzilla.kernel.org/show_bug.cgi?id=200195
Therefore restore the WoL behavior from 4.16.
Reported-by: Albert Astals Cid <aacid@kde.org>
Fixes: 7edf6d314c ("r8169: disable WOL per default")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The removed code would be called in two situations:
1. interface is brought up never or >10s after driver load
2. after close()
Case 1 we can handle cleaner by ensuring chip is powered down when
leaving probe(). open() callback will power up the chip.
In case 2 we call rtl_pll_power_down() twice currently, from the
close() callback and 10s later when entering runtime-suspend.
This is avoided by this patch.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of accessing the PHYstatus register we can use the information
phylib stores in the phy_device structure.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only remaining usage of the struct mii_if_info member is to store the
information whether the chip is GMII-capable. So we can replace it with
a simple flag.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can remove rtl8169_set_speed_xmii() now that phylib handles all this.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use new phylib functions phy_speed_down() and phy_speed_up().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch to using phy_mii_ioctl().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch to using phy_ethtool_nway_reset().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use phy_ethtool_(g|s)et_link_ksettings() for the respective ethtool_ops
callbacks.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use genphy_soft_reset() instead of open-coding a PHY soft reset. We have
to do an explicit PHY soft reset because some chips use the genphy driver
which uses a no-op as soft_reset callback.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use phy_resume() / phy_suspend() instead of open coding this functionality.
The chip version specific differences are handled by the respective PHY
drivers.
The call to r8168_phy_power_down() in r8168_pll_power_down() can be
removed because phylib takes care now. The relevant scenarios are:
- rtl8169_close(): phy_disconnect() powers down PHY
- suspend: mdio_bus_phy_suspend() takes care
- runtime-suspend: WoL is active, don't suspend PHY
- rtl_shutdown(): no need to power down PHY
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add basic phylib support to r8169. All now unneeded old PHY handling code
will be removed in subsequent patches.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When runtime-suspending we configure WoL w/o touching saved_wolopts.
If saved_wolopts == 0 we would power down the PHY in this case what's
wrong. Therefore we have to check the actual chip WoL settings here.
Fixes: 433f9d0ddc ("r8169: improve saved_wolopts handling")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Network core refuses to change mac address because flag
IFF_LIVE_ADDR_CHANGE isn't set. Set this missing flag.
Fixes: 1f7aa2bc26 ("r8169: simplify rtl_set_mac_address")
Reported-by: Corinna Vinschen <vinschen@redhat.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Corinna Vinschen <vinschen@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This hack (affecting the non-PCIe models only) was introduced in 2004
to deal with link negotiation failures in 1GBit mode. Based on a
comment in the r8169 vendor driver I assume the issue affects RTL8169sb
in combination with particular 1GBit switch models.
Resetting the PHY every 10s and hoping that one fine day we will make
it to establish the link seems to be very hacky to me. I'd say:
If 1GBit doesn't work reliably in a users environment then the user
should remove 1GBit from the advertised modes, e.g. by using
ethtool -s <if> advertise <10/100 modes>
If the issue affects one chip version only and that with most link
partners, then we could also think of removing 1GBit from the
advertised modes for this chip version in the driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The very first version of RTL8169 from 2002 (and only this one) has
support for a TBI 1000BaseX fiber interface. The TBI support in the
driver makes switching to phylib tricky, so best would be to get
rid of it. I found no report from anybody using a device with RTL8169
and fiber interface, also the vendor driver doesn't support this mode
(any longer).
So remove TBI support and bail out with a message if a card with
activated TBI is detected. If there really should be any user of it
out there, we could add a stripped-down version of the driver
supporting chip version 01 and TBI only (and maybe move it to
staging).
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I see no need to define a private debug output symbol, let's use the
standard debug output functions instead. In this context also remove
the deprecated PFX define.
The one assertion is wrong IMO anyway, this code path is used also
by chip version 01.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far unsupported WoL options are silently ignored. Change this and
reject attempts to set unsupported options. This prevents situations
where a user tries to set an unsupported WoL option and is under the
impression it was successful because ethtool doesn't complain.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can power down the PHY irregardless of WOL settings if interface
is down. So far we would have left the PHY enabled if WOL options
are set and the interface is brought down.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let's make saved_wolopts a shadow copy of the WoL options. This allows
to simplify the code and get rid of calls to now unneeded function
__rtl8169_get_wol(). However don't remove __rtl8169_get_wol()
completely to be prepared for the case that we can respect BIOS WOL
settings again.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let's move calling rtl8169_init_phy() to __rtl8169_resume().
It simplifies the code and avoids rtl8169_init_phy() being called
when resuming whilst interface is down. rtl_open() will initialize
the PHY when the interface is brought up.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let's enable ASPM also on the RTL8168E-VL (chip version 34).
Works fine on my Zotac Mini PC with this chip. Temperature when
being idle is significantly lower than before due to reaching
deeper PC states.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The r8168 vendor driver always uses value 0x27. In r8169 we have few
chips where 0x17 is used. So far this didn't matter because ASPM was
disabled anyway. Now that ASPM was re-enabled let's also use 0x27 only.
One of the chips affected by this change is RTL8168E-VL, on my system
with this chip value 0x27 works fine.
In addition rename rtl_csi_access_enable_2() to
rtl_set_def_aspm_entry_latency() to make clear that we set the default
ASPM entry latency.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On Intel platforms (Skylake and newer), ASPM support in r8169 is the
last missing puzzle to let CPU's Package C-State reaches PC8. Without
ASPM support, the CPU cannot reach beyond PC3. PC8 can save additional
~3W in comparison with PC3 on a Coffee Lake platform, Dell G3 3779.
This is based on the work from Chunhao Lin <hau@realtek.com>.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable or disable ASPM should be done in PCI core instead of in the
device driver.
Commit ba04c7c93b ("r8169: disable ASPM") uses
pci_disable_link_state() to disable ASPM, but it's not the best way to
do it. If the device really wants to disable ASPM, we can use a quirk in
PCI core to prevent the PCI core from setting ASPM before probe.
Let's remove pci_disable_link_state() for now. Use PCI core quirks if
any regression happens.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass the correct thing to rtl8169_interrupt() from netpoll.
Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>
Cc: netdev@vger.kernel.org
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Fixes: ebcd5daa7f ("r8169: change interrupt handler argument type")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The call to free_netdev() in __rtl8139_cleanup_dev() clears the network device
napi list, and explicit calls to netif_napi_del() are unnecessary.
Signed-off-by: Bo Chen <chenbo@pdx.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit removed calls to rtl_set_rx_mode(). This is ok for the
standard path if the link is brought up, however it breaks system
resume from suspend. Link comes up but no network traffic.
Meanwhile common code from rtl_hw_start_8169/8101/8168() was moved
to rtl_hw_start(), therefore re-add the call to rtl_set_rx_mode()
there.
Due to adding this call we have to move definition of rtl_hw_start()
after definition of rtl_set_rx_mode().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Fixes: 82d3ff6dd1 ("r8169: remove calls to rtl_set_rx_mode")
Signed-off-by: David S. Miller <davem@davemloft.net>
The bpf syscall and selftests conflicts were trivial
overlapping changes.
The r8169 change involved moving the added mdelay from 'net' into a
different function.
A TLS close bug fix overlapped with the splitting of the TLS state
into separate TX and RX parts. I just expanded the tests in the bug
fix from "ctx->conf == X" into "ctx->tx_conf == X && ctx->rx_conf
== X".
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit a92a08499b "r8169: improve runtime pm in general and
suspend unused ports" interfaces w/o link are runtime-suspended after
10s. On systems where drivers take longer to load this can lead to the
situation that the interface is runtime-suspended already when it's
initially brought up.
This shouldn't be a problem because rtl_open() resumes MAC/PHY.
However with at least one chip version the interface doesn't properly
come up, as reported here:
https://bugzilla.kernel.org/show_bug.cgi?id=199549
The vendor driver uses a delay to give certain chip versions some
time to resume before starting the PHY configuration. So let's do
the same. I don't know which chip versions may be affected,
therefore apply this delay always.
This patch was reported to fix the issue for RTL8168h.
I was able to reproduce the issue on an Asus H310I-Plus which also
uses a RTL8168h. Also in my case the patch fixed the issue.
Reported-by: Slava Kardakov <ojab@ojab.ru>
Tested-by: Slava Kardakov <ojab@ojab.ru>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is basically the same as 6e74d1749a ("r8152: replace
get_protocol with vlan_get_protocol"). Use vlan_get_protocol
instead of duplicating the functionality.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Interpreting a member of an u16 array as u32 may result in a misaligned
access. Also it's not really intuitive to define a mac address variable
as array of three u16 words. Therefore use an array of six bytes that
is properly aligned for 32 bit access.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some chips have a non-zero function id, however instead of hardcoding
the id's (CSIAR_FUNC_NIC and CSIAR_FUNC_NIC2) we can get them
dynamically via PCI_FUNC(pci_dev->devfn). This way we can get rid
of the csi_ops.
In general csi is just a fallback mechanism for PCI config space
access in case no native access is supported. Therefore let's
try native access first.
I checked with Realtek regarding the functionality of config space
byte 0x070f and according to them it controls the L0s/L1
entrance latency.
Currently ASPM is disabled in general and therefore this value
isn't used. However we may introduce a whitelist for chips
where ASPM is known to work, therefore let's keep this code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only two places are left where rtl_generic_op() is used, so we can
inline it and simplify the code a little.
This change also avoids the overhead of unlocking/locking in case
the respective operation isn't set.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some longer if statements can be simplified by using switch
statements instead.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several switch statements can be significantly simplified by using
case ranges.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After merging r810x_pll_power_down/up and r8168_pll_power_down/up we
don't need member pll_power_ops any longer and can drop it, thus
simplifying the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
r810x_pll_power_down/up and r8168_pll_power_down/up have a lot in common,
so we can simplify the code by merging the former into the latter.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The functionality of 810x_phy_power_up/down is covered by the default
clause in 8168_phy_power_up/down. Therefore we don't need these
functions.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RTL_GIGA_MAC_VER_23/24 are configured by rtl_hw_start_8168cp_2()
and rtl_hw_start_8168cp_3() respectively which both apply
CPCMD_QUIRK_MASK, thus clearing bit ASF.
Bit ASF isn't set at any other place in the driver, therefore this
check can be removed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use disable_irq_nosync() instead of disable_irq() as this might be
called in atomic context with netpoll.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The chip-specific init code includes quite some calls which are
identical for all chips. So move these calls to tp->hw_start().
In addition move rtl_set_rx_max_size() a little to make sure it's
defined before it's used. Unfortunately the diff generated by git
is a little bit hard to read.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__dev_open() calls the ndo_set_rx_mode callback anyway, so we don't
have to do it here too.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently done:
- if mac_version in (01, 02, 03, 04)
RTL_W8(tp, ChipCmd, CmdTxEnb | CmdRxEnb);
- if mac_version in (01, 02, 03, 04)
rtl_set_rx_tx_config_registers(tp);
- if mac_version not in (01, 02, 03, 04)
RTL_W8(tp, ChipCmd, CmdTxEnb | CmdRxEnb);
rtl_set_rx_tx_config_registers(tp);
So we do exactly the same independent of chip version and can simplify
the code.
In addition remove the call to rtl_init_rxcfg(), it's called in
rtl_init_one() already and the set bits are never touched later.
rtl_init_8168/8101 don't include this call either.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both quirk masks are the same, so we can merge them. The quirk mask
includes most bits so it's actually easier to define a mask with
the bits to keep.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tp->cp_cmd is supposed to reflect the current value of the CplusCmd
register. Several (quite old) changes however directly change this
register w/o updating tp->cp_cmd. Also we have places in the code
reading this register where we could use the cached value.
In addition:
- Properly initialize tp->cmd with the register value.
- In rtl_hw_start_8169 remove one setting of PCIMulRW because it's
set unconditionally anyway a few lines later.
- In rtl_hw_start_8168 properly mask out the INTT bits before
setting INTT_1. So far we rely on both bits being zero.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__rtl8169_set_features is used in rtl8169_set_features only, so we
can inline it. In addition:
- Remove check (features ^ dev->features), __netdev_update_features
check's already that requested features differ from current ones.
- Don't mask out unsupported flags, there's no benefit in it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RxChkSum and RxVlan aren't touched outside __rtl8169_set_features
(except in probe), so they are always in sync with dev->features.
And the RxConfig flags are set in rtl_set_rx_mode() which is
called via dev_set_rx_mode() from __dev_open().
Therefore we can safely remove this call.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's no benefit in using netif_info et al before the net_device has
been registered. We get messages like
r8169 0000:03:00.0 (unnamed net_device) (uninitialized): [message]
Therefore use dev_info/dev_err instead.
As a side effect we don't need parameter dev for function
rtl8169_get_mac_version() any longer.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the chip configuration entries only RTL8169 (ver <= 06)
supports tx checksumming for jumbo packets.
By the way: constant JUMBO_1K is a little misleading because it refers
to the standard packet size and not to a jumbo packet size.
By implementing this rule we can get rid of configuring tx checksumming
support per chip type.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The region to be used is always the first of type IORESOURCE_MEM.
We can implement this rule directly w/o having to specify which
region is the first one per configuration entry.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
txd_version is used in rtl_init_one() only, so we can drop member
txd_version from struct rtl8169_private.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Certain entries in array mac_info[] are redundant, so remove them:
0x7cf, 0x2c200000 (VER 33): matched by entry 0x7c8, 0x2c000000
0x7cf, 0x28300000 (VER 26): matched by entry 0x7c8, 0x28000000
0x7cf, 0x3cb00000 (VER 24): matched by entry 0x7c8, 0x3c800000
0x7cf, 0x3c400000 (VER 22): matched by entry 0x7c8, 0x3c000000
0x7cf, 0x38500000 (VER 17): matched by entry 0x7c8, 0x38000000
0x7cf, 0x44900000 (VER 39): matched by entry 0x7c8, 0x44800000
0x7cf, 0x40b00000 (VER 30): matched by entry 0x7c8, 0x40800000
0x7cf, 0x40a00000 (VER 30): matched by entry 0x7c8, 0x40800000
0x7cf, 0x34a00000 (VER 09): matched by entry 0x7c8, 0x34800000
0x7cf, 0x24a00000 (VER 09): matched by entry 0x7c8, 0x24800000
In addition don't mask out bits 30 and 29 when printing the XID.
Most likely this is a relict from the times when the driver covered
RTL8169 chip version only.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For security reasons since commit ad67b74d24 "printk: hash addresses
printed with %p" %p doesn't display the full address any longer.
We could switch to %px, but I think the pointer address doesn't
provide a real benefit, so remove printing the hashed address.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can get rid of member opts1_mask and in addition save a few cpu
cycles in the hot path of rtl_rx().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Code can be a little simplified by switching the interrupt handler
argument type to struct rtl8169_private *.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The counter handling functions don't deal with the net_device, so code
can be simplified by changing the argument type to
struct rtl8169_private *.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
