Use the PRDI mode on 8x96 to allow to configure RAW MIPI10
to Plain16 format conversion.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Usually the format on the source pad is the same as on the sink pad.
However the CSID is able to do some format conversions. To support
this make the format on the source pad selectable amongst a list
of formats. This list can be different for each sink pad format.
This is still not used but will be when the format conversions
are implemented.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add support to output UYVY formats from the VFE (via the PIX interface).
A configuration for the realign module in the VFE is added. As the
realign module is present on 8x96 but not on 8x16, this is supported
on 8x96 only.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Rework the format selection on the source pad. Make the format
on the source pad selectable amongst a list of formats. This
list can be different for each sink pad format.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
As the 8x16 and 8x96 support different formats, separate the
arrays which contain the supported formats. For the VFE also
add separate arrays for RDI and PIX subdevices.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This will allow to add support for different hardware.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
ISPIF hardware modules on 8x16 and 8x96 are similar. However on
8x96 the ISPIF routes data to two VFE hardware modules. Add
separate interrupt handler for 8x96 to handle the additional
interrupts.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
CSID hardware modules on 8x16 and 8x96 are similar. There is no
need to duplicate the code by adding separate versions. Just
update the register macros to return the correct register
addresses.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Restructure lane configuration so it is simpler and will allow
similar (although not the same) handling for different hardware
versions.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This will allow to add support for different hardware.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
[hans.verkuil@cisco.com: remove trailing empty line]
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
There is a PM domain for each of the VFE hardware modules. Add
support for basic runtime PM support to be able to control the
PM domains. When a PM domain needs to be powered on - a device
link is created. When a PM domain needs to be powered off -
its device link is removed. This allows separate and
independent control of the PM domains.
Suspend/Resume is still not supported.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add structs with 8x96 resources. As the number of CSIPHY, CSID
and VFE hardware modules is different on 8x16 and 8x96 select
the number at runtime and allocate needed structures
dynamically.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use "no change" value when clearing CAMIF status and make sure
this is done before configuring the new command.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Simplify getting of the line pointer by using the container_of
macro instead of traversing media controller links.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use the member name which is "line" instead of the pointer argument.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The CSID decodes the input data stream. When the input comes from
the Test Generator the format of the stream is set on the source
media pad. When the input comes from the CSIPHY the format is the
one on the sink media pad. Use the proper format for each case.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use more logical clock names - similar to the names in documentation.
This will allow better handling of the clocks in the driver when support
for more hardware versions is added - equivalent clocks on different
hardware versions will have the same name.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use more logical clock names - similar to the names in documentation.
This will allow better handling of the clocks in the driver when support
for more hardware versions is added - equivalent clocks on different
hardware versions will have the same name.
Note: No dts is using this device (and clock names) yet.
CC: Rob Herring <robh+dt@kernel.org>
CC: Mark Rutland <mark.rutland@arm.com>
CC: devicetree@vger.kernel.org
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add a write memory barier after clock mux config and before the rest
of the csiphy config.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
of_graph_get_next_endpoint increases the refcount of the returned
node and decreases the refcount of the passed node. Take this into
account and use of_node_put properly.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use SPDX license headers for all files of the Qualcomm CAMSS driver.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Support for camera subsystem on QComm MSM8996/APQ8096 is to be added
so remove hardware version from CAMSS driver's path.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The new format will be called V4L2_PIX_FMT_Y10P.
It is similar to the V4L2_PIX_FMT_SBGGR10P family formats
but V4L2_PIX_FMT_Y10P is a grayscale format.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The code will be called MEDIA_BUS_FMT_Y10_2X8_PADHI_LE.
It is similar to MEDIA_BUS_FMT_SBGGR10_2X8_PADHI_LE
but MEDIA_BUS_FMT_Y10_2X8_PADHI_LE describes grayscale
data.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
These formats are compressed 14-bit raw bayer formats with four different
pixel orders. They are similar to 10-bit variants. The formats added by
this patch are
V4L2_PIX_FMT_SBGGR14P
V4L2_PIX_FMT_SGBRG14P
V4L2_PIX_FMT_SGRBG14P
V4L2_PIX_FMT_SRGGB14P
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This patch disables the null packet filter for the Hauppauge
WinTV-dualHD. There are applications which require the unfiltered
transport stream (e.g. DOCSIS segment load analyzers).
Tests showed that the device is capable of delivering two unfiltered
EuroDOCSIS 3.0 transport streams simultaneously, i.e. over 100 Mbit/s
worth of data, without any losses.
Signed-off-by: Robert Schlabbach <Robert.Schlabbach@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add a break statement in set_params() for the SYS_DVBT(2).
As reported by gcc:
drivers/media/dvb-frontends/tda18271c2dd.c:1144:3: warning: this statement may fall through [-Wimplicit-fallthrough=]
There is a nested switch() inside the code with sets the tuner to
the right standard. Without the break, the code will always set to
DVB-C mode, with can be sub-optimal for DVB-T.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Take note that the SX8 IQ mode is only available on a single tuner, and
remove the MCI/SX8 DIAG CMD defines.
Picked up from the upstream dddvb GIT.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Allow for tuning to transponders with specific modulations in
set_parameters(). Setting a specific modulation will also enable lower
modulations.
Picked up from the upstream dddvb GIT. Upstream also has support for
APSK64/128/256 modulations which aren't supported yet by the DVB
API, so comment them out until support for them is added.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The SX8 cards by default do an automatic search for the PLS code. This
is not necessarily wanted as this can eventually be detected wrong, so
disable this.
Picked up from the upstream dddvb GIT.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The MCI can report the command status more finegrained, so, add more
status code defines and update the MCI_SUCCESS macro.
Picked up from the upstream dddvb GIT.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Split off all code specific to the MaxSX8 cards to a separate ddbridge-sx8
module and hook it up in the Makefile. This also adds evaluation of the
mci_type to allow for using different attach handling for different cards.
As different cards can implement things differently (ie. support differing
frontend_ops, and have different base structs being put ontop of the
common mci_base struct), this introduces the mci_cfg struct which is
initially used to hold a few specifics to the -sx8 submodule. While at it,
the handling of the i/q mode is adjusted slightly. Besides this and
handling mci_base and sx8_base struct pointers where needed, all code
is copied unmodified from ddbridge-mci.c.
Picked up from the upstream dddvb GIT.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In preparation for splitting all MaxSX8 related code parts from the common
MCI code, prefix both mci_cmd() and mci_config() functions with ddb_,
remove the static marking and add matching function prototypes to
ddbridge-mci.h so these functions can be reused from other files within
the ddbridge driver. As this requires the mci-related structs to be
defined in ddbridge-mci.h, move struct mci and struct mci_base there and
clean them up.
Picked up from the upstream dddvb GIT.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
For better support for future MCI based cards, rename the mci struct
member to mci_ports to carry the number of ports on the cards, and add a
mci_type member to identify the card type to handle differing hardware.
Picked up from the upstream dddvb GIT.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Recent FPGA firmware reports more data and values in sent command
responses. Adjust the mci_command and mci_result structs including it's
unions to match these changes and add a few comments explaining things.
Picked up from the upstream dddvb GIT.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Adjustments to match the FPGA firmware, and the signal I/Q values are
reported as s16 types from the card firmware.
Picked up from the upstream dddvb GIT.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Implement querying signal statistics from the MCI and report this data
in read_status() as DVBv5 statistics.
Picked up from the upstream dddvb GIT.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Update the copyright year information in the MCI headers to 2017-2018.
Picked up from the upstream dddvb GIT.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Change the start of the MCI ID range (internally used only) to 48 and
define an ID for the SX8 card type. Use this new ID to handle device
attachment.
This change is done in preparation for support of more MCI based cards.
Picked up from the upstream dddvb GIT.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Throughout the function, dev->link[l] is used several times. Unclutter
this a bit by declaring a ddb_link var at the top of the function, assign
the address of dev->link[l] to it and use that var to access the link[]
struct member.
Picked up from the upstream dddvb GIT.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
ddbridge has a few MDIO related remainders (defines, hwinfo struct) which
aren't of any use for the in-kernel driver at all (they're only used in
conjunction with the OctoNet SAT>IP boxes which the kernel driver doesn't
have any support for), so clean this up.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The I2C_COMMAND response reports an error in the I2C bus communication
using bit 17. Evaluate the response more thoroughly and log an error
if an I2C problem was detected.
Picked up from the upstream dddvb GIT.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Devices supporting dummy tuner operation can exist on any link, not only
on link 0, so fix this accordingly.
Picked up from the upstream dddvb GIT.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In demod_attach_stv0910(), the LNBH25 IC is being blindly attached and,
if the result is bad, blindly attached on another possible I2C address.
The LNBH25 uses it's set_voltage function to test for the IC and will
print an error to the kernel log on failure. Prevent this by probing
the possible I2C address and use this (and only this) to attach the
LNBH25 I2C driver. This also allows the stv0910 attach function to be
a bit cleaner.
Picked up from the upstream dddvb GIT and adapted for the LNBH25 driver
variant from the kernel tree.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
To avoid miscalculations related to the BER denominator, the shift
expression needs to be casted as ULL.
Picked up from the upstream dddvb GIT.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
