The discipline struct is a fixed group of function pointers.
So declare the L2 and L3 disciplines as constant.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For OSA devices that are _not_ configured in prio-queue mode, give users
the option of selecting the number of active TX queues.
This requires setting up the HW queues with a reasonable default QoS
value in the QIB's PQUE parm area.
As with the other device types, we bring up the device with a minimal
number of TX queues for compatibility reasons.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a proper struct, and only program the QIB extensions for devices
where they are supported.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When re-initializing a device, we can hit a situation where
qeth_osa_set_output_queues() detects that it supports more or less
HW TX queues than before. Right now we adjust dev->real_num_tx_queues
from right there, but
1. it's getting more & more complicated to cover all cases, and
2. we can't re-enable the actually expected number of TX queues later
because we lost the needed information.
So keep track of the wanted TX queues (on initial setup, and whenever
its changed via .set_channels), and later use that information when
re-enabling the netdevice.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With SMCD version 2 the CHIDs of ISM devices are needed for the
CLC handshake.
This patch provides the new callback to retrieve the CHID of an
ISM device.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SMCD version 2 defines a System Enterprise ID (short SEID).
This patch contains the SEID creation and adds the callback to
retrieve the created SEID.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shuffle some code around (primarily all the discipline-related stuff) to
get rid of all the unnecessary forward declarations.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clarify which discipline-specific steps are needed to roll back after
error in qeth_l?_set_online(), and which are common to roll back
from qeth_hardsetup_card().
Some steps (cancelling the RX modeset, draining the TX queues) are only
necessary if the netdev was potentially UP before, so move them to the
common qeth_set_offline().
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move duplicated code from the disciplines into the core path.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Originators of cmd IO typically hold the rtnl or conf_mutex to protect
against a concurrent teardown.
Since qeth_set_offline() already holds the conf_mutex, the main reason
why we still care about cancelling pending cmds is so that they release
the rtnl when we need it ourselves.
So move this step a little earlier into the teardown sequence.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The programming of ucast IPs via qeth_l3_modify_ip() is driven
independently from any of our typical locking mechanisms (eg. detaching
the netdevice, or holding the conf_mutex).
So when we inspect the card state to check whether the required cmd IO
should be deferred, there is no protection against concurrent state
changes.
But by slightly re-ordering the teardown sequence, we can rely on the
ip_lock to sufficiently serialize things:
1. when running concurrently to qeth_l3_set_online(), any instance of
qeth_l3_modify_ip() that aquires the ip_lock _after_
qeth_l3_recover_ip() will observe the state as CARD_STATE_SOFTSETUP
and not defer the IO.
2. when running concurrently to qeth_l3_set_offline(), any instance of
qeth_l3_modify_ip() that aquires the ip_lock _after_
qeth_l3_clear_ip_htable() will observe the state as CARD_STATE_DOWN
and defer the IO.
These guarantees in mind, we can now drop the conf_mutex from the
qeth_l3_modify_rxip_vipa() wrapper.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the remaining occurences in sysfs code to kstrtouint().
While at it move some input parsing out of locked sections, replace an
open-coded clamp() and remove some unnecessary run-time checks for
ipatoe->mask_bits that are already enforced when creating the object.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Indicate the max number of to-be-parsed characters, and avoid copying
the address sub-string.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
card->ipato is currently protected by the conf_mutex. But most users
also hold the ip_lock - in particular qeth_l3_add_ip().
So slightly expand the sections under ip_lock in a few places (to
effectively cover a few error & no-op cases), and then drop the
conf_mutex where it's no longer needed.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mcast IP objects are allocated within qeth_l3_add_mcast_rtnl(),
with .ref_counter already set to 1 via qeth_l3_init_ipaddr().
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two minor conflicts:
1) net/ipv4/route.c, adding a new local variable while
moving another local variable and removing it's
initial assignment.
2) drivers/net/dsa/microchip/ksz9477.c, overlapping changes.
One pretty prints the port mode differently, whilst another
changes the driver to try and obtain the port mode from
the port node rather than the switch node.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from Jakub Kicinski:
- fix failure to add bond interfaces to a bridge, the offload-handling
code was too defensive there and recent refactoring unearthed that.
Users complained (Ido)
- fix unnecessarily reflecting ECN bits within TOS values / QoS marking
in TCP ACK and reset packets (Wei)
- fix a deadlock with bpf iterator. Hopefully we're in the clear on
this front now... (Yonghong)
- BPF fix for clobbering r2 in bpf_gen_ld_abs (Daniel)
- fix AQL on mt76 devices with FW rate control and add a couple of AQL
issues in mac80211 code (Felix)
- fix authentication issue with mwifiex (Maximilian)
- WiFi connectivity fix: revert IGTK support in ti/wlcore (Mauro)
- fix exception handling for multipath routes via same device (David
Ahern)
- revert back to a BH spin lock flavor for nsid_lock: there are paths
which do require the BH context protection (Taehee)
- fix interrupt / queue / NAPI handling in the lantiq driver (Hauke)
- fix ife module load deadlock (Cong)
- make an adjustment to netlink reply message type for code added in
this release (the sole change touching uAPI here) (Michal)
- a number of fixes for small NXP and Microchip switches (Vladimir)
[ Pull request acked by David: "you can expect more of this in the
future as I try to delegate more things to Jakub" ]
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (167 commits)
net: mscc: ocelot: fix some key offsets for IP4_TCP_UDP VCAP IS2 entries
net: dsa: seville: fix some key offsets for IP4_TCP_UDP VCAP IS2 entries
net: dsa: felix: fix some key offsets for IP4_TCP_UDP VCAP IS2 entries
inet_diag: validate INET_DIAG_REQ_PROTOCOL attribute
net: bridge: br_vlan_get_pvid_rcu() should dereference the VLAN group under RCU
net: Update MAINTAINERS for MediaTek switch driver
net/mlx5e: mlx5e_fec_in_caps() returns a boolean
net/mlx5e: kTLS, Avoid kzalloc(GFP_KERNEL) under spinlock
net/mlx5e: kTLS, Fix leak on resync error flow
net/mlx5e: kTLS, Add missing dma_unmap in RX resync
net/mlx5e: kTLS, Fix napi sync and possible use-after-free
net/mlx5e: TLS, Do not expose FPGA TLS counter if not supported
net/mlx5e: Fix using wrong stats_grps in mlx5e_update_ndo_stats()
net/mlx5e: Fix multicast counter not up-to-date in "ip -s"
net/mlx5e: Fix endianness when calculating pedit mask first bit
net/mlx5e: Enable adding peer miss rules only if merged eswitch is supported
net/mlx5e: CT: Fix freeing ct_label mapping
net/mlx5e: Fix memory leak of tunnel info when rule under multipath not ready
net/mlx5e: Use synchronize_rcu to sync with NAPI
net/mlx5e: Use RCU to protect rq->xdp_prog
...
-----BEGIN PGP SIGNATURE-----
iQJEBAABCAAuFiEEwPw5LcreJtl1+l5K99NY+ylx4KYFAl9qLq8QHGF4Ym9lQGtl
cm5lbC5kawAKCRD301j7KXHgpqrCD/4hjvDuZIDMZILnOhHtZPB+q1bnf48dcB2v
WQlDJAZVDKIdBy49gN2mraLwbeKvnzTv25kfZkXZPL4F32TuXK8E57tHPCYEq5li
qb6y3o0Y1y0p78PtYittfWeUWaYkT2v91QQjLc6Vyh8swL15XDQ37lBw7qqtNUhw
WMTS1Q2bw0wjltRAC5XSTD73PwcjFMYhE/1YBWE4vckaB1K+kLN6RRaVZ03unC/U
zhSd2WqZyHwaEsl66Vtl7ty+SMoqahfXNvBcvvLVY6mD2U0hLWCBlnWY5SjYmzLZ
3lVqmiL+diaAoDRroQnpFkAJSRnnWv3g3gWbygbSKJScFGKh15k7Px4ztWr233Xb
KZtoZN826PhSkujIB8wKaFrrx3Zz00a9flqvum2ejOQAP5FiS2QRLlaZuf2U2xqm
5AhZ7ul1qm9kik0ZULPBY1myK1Y8sSoKSnu3WAVUPo974fAPTvhWUpO+i6SssYWu
oI2VUK9BvcgP1MjMms1EYEpY8rg8G+TGzN+P6jJcBirAAecdpXhLaLwOdEQC9De/
P/OfyHg6lIgs9PP0NOp8BeUDQe9bDW8gNxv57R57+N7ZIKP0443LwSaHpmFInBC+
lxAGcghsl++TZZ+sCDM8Lkw5IZWcc/czewHzVFVMjpnivt0kuQrndFyOxRdHjggy
4Vo1Sa1Ahg==
=zT03
-----END PGP SIGNATURE-----
Merge tag 'block-5.9-2020-09-22' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"A few NVMe fixes, and a dasd write zero fix"
* tag 'block-5.9-2020-09-22' of git://git.kernel.dk/linux-block:
nvmet: get transport reference for passthru ctrl
nvme-core: get/put ctrl and transport module in nvme_dev_open/release()
nvme-tcp: fix kconfig dependency warning when !CRYPTO
nvme-pci: disable the write zeros command for Intel 600P/P3100
s390/dasd: Fix zero write for FBA devices
Documentation/networking/switchdev.txt and 'man bridge' indicate that the
learning_sync bridge attribute is used to control whether a given
device will sync MAC addresses learned on its device port to a master
bridge FDB, where they will show up as 'extern_learn offload'. So we map
qeth_l2_dev2br_an_set() to the learning_sync bridge link attribute.
Turning off learning_sync will flush all extern_learn entries from the
bridge fdb and all pending events from the card's work queue.
When the hardware interface goes offline with learning_sync on
(e.g. for HW recovery), all extern_learn entries will be flushed from the
bridge fdb and all pending events from the card's work queue. When the
interface goes online again, it will send new notifications for all then
valid MACs. learning_sync attribute can not be modified while interface is
offline. See
'commit e6e771b3d8 ("s390/qeth: detach netdevice while card is offline")'
An alternative implementation would be to always offload the 'learning'
attribute of a software bridge to the hardware interface attached to it
and thus implicitly enable fdb notification. This was not chosen for 2
reasons:
1) In our case the software bridge is NOT a representation of a hardware
switch. It is just connected to a smart NIC that is able to inform
about the addresses attached to it. It is not necessarily using source
MAC learning for this and other bridgeports can be attached to other
NICs with different properties.
2) We want a means to enable this notification explicitly. There may be
cases where a bridgeport is set to 'learning', but we do not want to
enable the notification.
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Documentation/networking/switchdev.txt and 'man bridge' indicate that the
learning_sync bridge attribute is used to indicate whether a given
device will sync MAC addresses learned on its device port to a master
bridge FDB.
learning_sync attribute can not be read while interface is offline (down).
See
'commit e6e771b3d8 ("s390/qeth: detach netdevice while card is offline")'
We return EOPNOTSUPP and not EONODEV in this case, because EONOTSUPP is the
only rc that is tolerated by 'bridge -d link show'.
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case hardware sends more device-to-bridge-address-change notfications
than the qeth-l2 driver can handle, the hardware will send an overflow
event and then stop sending any events. It expects software to flush its
FDB and start over again. Re-enabling address-change-notification will
report all current addresses.
In order to re-enable address-change-notification this patch defines
the functions qeth_l2_dev2br_an_set() and qeth_l2_dev2br_an_set_cb
to enable or disable dev-to-bridge-address-notification.
A following patch will use the learning_sync bridgeport flag to trigger
enabling or disabling of address-change-notification, so we define
priv->brport_features to store the current setting. BRIDGE_INFO and
ADDR_INFO functionality are mutually exclusive, whereas ADDR_INFO and
qeth_l2_vnicc* can be used together.
Alternative implementations to handle buffer overflow:
Just re-enabling notification and adding all newly reported addresses
would cover any lost 'add' events, but not the lost 'delete' events.
Then these invalid addresses would stay in the bridge FDB as long as the
device exists.
Setting the net device down and up, would be an alternative, but is a bit
drastic. If the net device has many secondary addresses this will create
many delete/add events at its peers which could de-stabilize the
network segment.
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A qeth-l2 HiperSockets card can show switch-ish behaviour in the sense,
that it can report all MACs that are reachable via this interface. Just
like a switch device, it can notify the software bridge about changes
to its fdb. This patch exploits this device-to-bridge-notification and
extracts the relevant information from the hardware events to generate
notifications to an attached software bridge.
There are 2 sources for this information:
1) The reply message of Perform-Network-Subchannel-Operations (PNSO)
(operation code ADDR_INFO) reports all addresses that are currently
reachable (implemented in a later patch).
2) As long as device-to-bridge-notification is enabled, hardware will
generate address change notification events, whenever the content of
the hardware fdb changes (this patch).
The bridge_hostnotify feature (PNSO operation code BRIDGE_INFO) uses
the same address change notification events. We need to distinguish
between qeth_pnso_mode QETH_PNSO_BRIDGEPORT and QETH_PNSO_ADDR_INFO
and call a different handler. In both cases deadlocks must be
prevented, if the workqueue is drained under lock and QETH_PNSO_NONE,
when notification is disabled.
bridge_hostnotify generates udev events, there is no intend to do the same
for dev2br. Instead this patch will generate SWITCHDEV_FDB_ADD_TO_BRIDGE
and SWITCHDEV_FDB_DEL_TO_BRIDGE notifications, that will cause the
software bridge to add (or delete) entries to its fdb as 'extern_learn
offload'.
Documentation/networking/switchdev.txt proposes to add
"depends NET_SWITCHDEV" to driver's Kconfig. This is not done here,
so even in absence of the NET_SWITCHDEV module, the QETH_L2 module will
still be built, but then the switchdev notifiers will have no effect.
No VLAN filtering is done on the entries and VLAN information is not
passed on to the bridge fdb entries. This could be added later.
For now VLAN interfaces can be defined on the upper bridge interface.
Multicast entries are not passed on to the bridge fdb.
This could be added later. For now mcast flooding can be used in the
bridge.
The card reports all MACs that are in its FDB, but we must not pass on
MACs that are registered for this interface.
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch detects whether device-to-bridge-notification, provided
by the Perform Network Subchannel Operation (PNSO) operation code
ADDR_INFO (OC3), is supported by this card. A following patch will
map this to the learning_sync bridgeport flag, so we store it in
priv->brport_hw_features in bridgeport flag format.
Only IQD cards provide PNSO.
There is a feature bit to indicate whether the machine provides OC3,
unfortunately it is not set on old machines.
So PNSO is called to find out. As this will disable notification
and is exclusive with bridgeport_notification, this must be done
during card initialisation before previous settings are restored.
PNSO functionality requires some configuration values that are added to
the qeth_card.info structure. Some helper functions are defined to fill
them out when the card is brought online and some other places are
adapted, that can also benefit from these fields.
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add helper functions to expose Channel Subsystem ID (CSSID), MIF Image Id
(IID), Channel ID (CHID) and Channel Path ID (CHPID).
These values are required by the qeth driver's exploitation of network-
address-change-notifications to determine which entries belong to this
interface.
Store the Partition identifier in System log, as this may be used to map
a Linux view to a Hardware view for debugging purpose.
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Vineeth Vijayan <vneethv@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for operation code 3 (OC3) of the
Perform-Network-Subchannel-Operations (PNSO) function
of the Channel-Subsystem-Call (CHSC) instruction.
PNSO provides 2 operation codes:
OC0 - BRIDGE_INFO
OC3 - ADDR_INFO (new)
Extend the function calls to *pnso* to pass the OC and
add new response code 0108.
Support for OC3 is indicated by a flag in the css_general_characteristics.
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Reviewed-by: Vineeth Vijayan <vneethv@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A discard request that writes zeros using the global kernel internal
ZERO_PAGE will fail for machines with more than 2GB of memory due to the
location of the ZERO_PAGE.
Fix this by using a driver owned global zero page allocated with GFP_DMA
flag set.
Fixes: 28b841b3a7 ("s390/dasd: Add discard support for FBA devices")
Signed-off-by: Jan Höppner <hoeppner@linux.ibm.com>
Reviewed-by: Stefan Haberland <sth@linux.ibm.com>
Cc: <stable@vger.kernel.org> # 4.14+
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Tests showed that under stress conditions the kernel may
temporary fail to allocate 256k with kmalloc. However,
this fix reworks the related code in the cca_findcard2()
function to use kvmalloc instead.
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Reviewed-by: Ingo Franzki <ifranzki@linux.ibm.com>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
arch/s390/net/pnet.c uses ccwgroup function dev_is_ccwgroup()
in pnetid_by_dev_port().
For s390 the net/smc code makes use of function pnetid_by_dev_port().
Make sure ccwgroup is built into the kernel, if smc is to be built
into the kernel.
Signed-off-by: Guvenc Gulce <guvenc@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wait until the QDIO data connection is severed. Otherwise the device
might still be processing the buffers, and end up accessing skb data
that we already freed.
Fixes: 8b5026bc16 ("s390/qeth: fix qdio teardown after early init error")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We got slightly different patches removing a double word
in a comment in net/ipv4/raw.c - picked the version from net.
Simple conflict in drivers/net/ethernet/ibm/ibmvnic.c. Use cached
values instead of VNIC login response buffer (following what
commit 507ebe6444 ("ibmvnic: Fix use-after-free of VNIC login
response buffer") did).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The current code for bridge address events has two shortcomings in its
control sequence:
1. after disabling address events via PNSO, we don't flush the remaining
events from the event_wq. So if the feature is re-enabled fast
enough, stale events could leak over.
2. PNSO and the events' arrival via the READ ccw device are unordered.
So even if we flushed the workqueue, it's difficult to say whether
the READ device might produce more events onto the workqueue
afterwards.
Fix this by
1. explicitly fencing off the events when we no longer care, in the
READ device's event handler. This ensures that once we flush the
workqueue, it doesn't get additional address events.
2. Flush the workqueue after disabling the events & fencing them off.
As the code that triggers the flush will typically hold the sbp_lock,
we need to rework the worker code to avoid a deadlock here in case
of a 'notifications-stopped' event. In case of lock contention,
requeue such an event with a delay. We'll eventually aquire the lock,
or spot that the feature has been disabled and the event can thus be
discarded.
This leaves the theoretical race that a stale event could arrive
_after_ we re-enabled ourselves to receive events again. Such an event
would be impossible to distinguish from a 'good' event, nothing we can
do about it.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The data returned from IPA_SBP_QUERY_BRIDGE_PORTS and
IPA_SBP_BRIDGE_PORT_STATE_CHANGE has the same format. Use a single
struct definition for it.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current code copies _all_ entries from the event into a worker, when we
later only need specific data from the first entry.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only time that our Bridgeport role should change is when we change
the configuration ourselves. In which case we also adjust our internal
state tracking, no need to do it again when we receive the corresponding
event.
Removing the locked section helps a subsequent patch that needs to flush
the workqueue while under sbp_lock.
It would be nice to raise a warning here in case HW does weird things
after all, but this could end up generating false-positives when we
change the configuration ourselves.
Suggested-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A newly initialized device is disabled for address events, there's no
need to explicitly disable them.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
queue->state is a ternary spinlock in disguise, used by
OSA's TX completion path to lock the Output Queue and flush any pending
packets on it to the device. If the Queue is already locked by our TX
code, setting the lock word to QETH_OUT_Q_LOCKED_FLUSH lets the TX
completion code move on - the TX path will later take care of things
when it unlocks the Queue.
This sort of DIY locking is a non-starter of course, just let the
TX completion path block on the spinlock when necessary. If that ends up
causing additional latency due to lock contention, then converting
the OSA path to use xmit_more is the right way to go forward.
Also slightly expand the locked section and capture all of
qeth_do_send_packet(), so that the update for the 'bufs_pack' statistics
is done race-free.
While reworking the TX completion path's code, remove a barrier() that
doesn't make any sense.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid poking around in the delayed_work struct's internals.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clarify that the 'ipacmd' parameter is an enum, and thus compatible to
what qeth_ipa_alloc_cmd() expects as input.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Couple of fixes for storage key handling relevant for debugging.
- Add cond_resched into potentially slow subchannels scanning loop.
- Fixes for PF/VF linking and to ignore stale PCI configuration request
events.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE3QHqV+H2a8xAv27vjYWKoQLXFBgFAl9BDkAACgkQjYWKoQLX
FBhF3gf+KmVa7/Eb9Z0jE6dS1op5mggBASIMk7wr/enwSBQ7bLa42iGQPP9b7lWu
5FTLifmrelVIAadDjFU7+vfBYY4CtTg+KvaajlJeAe4QScND+KN3G7LkT+kRnqxy
n6evcW19yKKos2I+cVlqL0QxOXQBsQFM7wmpOrf373OBRqDyJAkV1DjcLopPZr8I
eMaKyhlLMoyxaoXkddk+RC417aIkuL900WaUMmdEkREIhawWbuyKoWqypk76CXih
Jtxgi1nSCX7nSVUnrLHLl4xPdpBziQ3iqccliddysNEbLsaqrdWbiP8XAPBrI8na
WxbFFOmHXTcTzhqpUDgyMv10fQtkBg==
=bgLc
-----END PGP SIGNATURE-----
Merge tag 's390-5.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Vasily Gorbik:
- a couple of fixes for storage key handling relevant for debugging
- add cond_resched into potentially slow subchannels scanning loop
- fixes for PF/VF linking and to ignore stale PCI configuration request
events
* tag 's390-5.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/pci: fix PF/VF linking on hot plug
s390/pci: re-introduce zpci_remove_device()
s390/pci: fix zpci_bus_link_virtfn()
s390/ptrace: fix storage key handling
s390/runtime_instrumentation: fix storage key handling
s390/pci: ignore stale configuration request event
s390/cio: add cond_resched() in the slow_eval_known_fn() loop
Before v4.15 commit 75492a5156 ("s390/scsi: Convert timers to use
timer_setup()"), we intentionally only passed zfcp_adapter as context
argument to zfcp_fsf_request_timeout_handler(). Since we only trigger
adapter recovery, it was unnecessary to sync against races between timeout
and (late) completion. Likewise, we only passed zfcp_erp_action as context
argument to zfcp_erp_timeout_handler(). Since we only wakeup an ERP action,
it was unnecessary to sync against races between timeout and (late)
completion.
Meanwhile the timeout handlers get timer_list as context argument and do a
timer-specific container-of to zfcp_fsf_req which can have been freed.
Fix it by making sure that any request timeout handlers, that might just
have started before del_timer(), are completed by using del_timer_sync()
instead. This ensures the request free happens afterwards.
Space time diagram of potential use-after-free:
Basic idea is to have 2 or more pending requests whose timeouts run out at
almost the same time.
req 1 timeout ERP thread req 2 timeout
---------------- ---------------- ---------------------------------------
zfcp_fsf_request_timeout_handler
fsf_req = from_timer(fsf_req, t, timer)
adapter = fsf_req->adapter
zfcp_qdio_siosl(adapter)
zfcp_erp_adapter_reopen(adapter,...)
zfcp_erp_strategy
...
zfcp_fsf_req_dismiss_all
list_for_each_entry_safe
zfcp_fsf_req_complete 1
del_timer 1
zfcp_fsf_req_free 1
zfcp_fsf_req_complete 2
zfcp_fsf_request_timeout_handler
del_timer 2
fsf_req = from_timer(fsf_req, t, timer)
zfcp_fsf_req_free 2
adapter = fsf_req->adapter
^^^^^^^ already freed
Link: https://lore.kernel.org/r/20200813152856.50088-1-maier@linux.ibm.com
Fixes: 75492a5156 ("s390/scsi: Convert timers to use timer_setup()")
Cc: <stable@vger.kernel.org> #4.15+
Suggested-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The scanning through subchannels during the time of an event could
take significant amount of time in case of platforms with lots of
known subchannels. This might result in higher scheduling latencies
for other tasks especially on systems with a single CPU. Add
cond_resched() call, as the loop in slow_eval_known_fn() can be
executed for a longer duration.
Reviewed-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Vineeth Vijayan <vneethv@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
In the first place, the initialization value of `rc` is wrong.
It is unnecessary to initialize `rc` variables, so remove their
initialization operation.
Fixes: f2bbc96e7c ("s390/pkey: add CCA AES cipher key support")
Signed-off-by: Tianjia Zhang <tianjia.zhang@linux.alibaba.com>
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Merge misc updates from Andrew Morton:
- a few MM hotfixes
- kthread, tools, scripts, ntfs and ocfs2
- some of MM
Subsystems affected by this patch series: kthread, tools, scripts, ntfs,
ocfs2 and mm (hofixes, pagealloc, slab-generic, slab, slub, kcsan,
debug, pagecache, gup, swap, shmem, memcg, pagemap, mremap, mincore,
sparsemem, vmalloc, kasan, pagealloc, hugetlb and vmscan).
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (162 commits)
mm: vmscan: consistent update to pgrefill
mm/vmscan.c: fix typo
khugepaged: khugepaged_test_exit() check mmget_still_valid()
khugepaged: retract_page_tables() remember to test exit
khugepaged: collapse_pte_mapped_thp() protect the pmd lock
khugepaged: collapse_pte_mapped_thp() flush the right range
mm/hugetlb: fix calculation of adjust_range_if_pmd_sharing_possible
mm: thp: replace HTTP links with HTTPS ones
mm/page_alloc: fix memalloc_nocma_{save/restore} APIs
mm/page_alloc.c: skip setting nodemask when we are in interrupt
mm/page_alloc: fallbacks at most has 3 elements
mm/page_alloc: silence a KASAN false positive
mm/page_alloc.c: remove unnecessary end_bitidx for [set|get]_pfnblock_flags_mask()
mm/page_alloc.c: simplify pageblock bitmap access
mm/page_alloc.c: extract the common part in pfn_to_bitidx()
mm/page_alloc.c: replace the definition of NR_MIGRATETYPE_BITS with PB_migratetype_bits
mm/shuffle: remove dynamic reconfiguration
mm/memory_hotplug: document why shuffle_zone() is relevant
mm/page_alloc: remove nr_free_pagecache_pages()
mm: remove vm_total_pages
...
As said by Linus:
A symmetric naming is only helpful if it implies symmetries in use.
Otherwise it's actively misleading.
In "kzalloc()", the z is meaningful and an important part of what the
caller wants.
In "kzfree()", the z is actively detrimental, because maybe in the
future we really _might_ want to use that "memfill(0xdeadbeef)" or
something. The "zero" part of the interface isn't even _relevant_.
The main reason that kzfree() exists is to clear sensitive information
that should not be leaked to other future users of the same memory
objects.
Rename kzfree() to kfree_sensitive() to follow the example of the recently
added kvfree_sensitive() and make the intention of the API more explicit.
In addition, memzero_explicit() is used to clear the memory to make sure
that it won't get optimized away by the compiler.
The renaming is done by using the command sequence:
git grep -w --name-only kzfree |\
xargs sed -i 's/kzfree/kfree_sensitive/'
followed by some editing of the kfree_sensitive() kerneldoc and adding
a kzfree backward compatibility macro in slab.h.
[akpm@linux-foundation.org: fs/crypto/inline_crypt.c needs linux/slab.h]
[akpm@linux-foundation.org: fix fs/crypto/inline_crypt.c some more]
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: David Howells <dhowells@redhat.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Cc: James Morris <jmorris@namei.org>
Cc: "Serge E. Hallyn" <serge@hallyn.com>
Cc: Joe Perches <joe@perches.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: "Jason A . Donenfeld" <Jason@zx2c4.com>
Link: http://lkml.kernel.org/r/20200616154311.12314-3-longman@redhat.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This series consists of the usual driver updates (ufs, qla2xxx, tcmu,
lpfc, hpsa, zfcp, scsi_debug) and minor bug fixes. We also have a
huge docbook fix update like most other subsystems and no major update
to the core (the few non trivial updates are either minor fixes or
removing an unused feature [scsi_sdb_cache]).
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXyxq1yYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishSoAAQChZ4i8
ZqYW3pL33JO3fA8vdjvLuyC489Hj4wzIsl3/bQEAxYyM6BSLvMoLWR2Plq/JmTLm
4W/LDptarpTiDI3NuDc=
=4b0W
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This consists of the usual driver updates (ufs, qla2xxx, tcmu, lpfc,
hpsa, zfcp, scsi_debug) and minor bug fixes.
We also have a huge docbook fix update like most other subsystems and
no major update to the core (the few non trivial updates are either
minor fixes or removing an unused feature [scsi_sdb_cache])"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (307 commits)
scsi: scsi_transport_srp: Sanitize scsi_target_block/unblock sequences
scsi: ufs-mediatek: Apply DELAY_AFTER_LPM quirk to Micron devices
scsi: ufs: Introduce device quirk "DELAY_AFTER_LPM"
scsi: virtio-scsi: Correctly handle the case where all LUNs are unplugged
scsi: scsi_debug: Implement tur_ms_to_ready parameter
scsi: scsi_debug: Fix request sense
scsi: lpfc: Fix typo in comment for ULP
scsi: ufs-mediatek: Prevent LPM operation on undeclared VCC
scsi: iscsi: Do not put host in iscsi_set_flashnode_param()
scsi: hpsa: Correct ctrl queue depth
scsi: target: tcmu: Make TMR notification optional
scsi: target: tcmu: Implement tmr_notify callback
scsi: target: tcmu: Fix and simplify timeout handling
scsi: target: tcmu: Factor out new helper ring_insert_padding
scsi: target: tcmu: Do not queue aborted commands
scsi: target: tcmu: Use priv pointer in se_cmd
scsi: target: Add tmr_notify backend function
scsi: target: Modify core_tmr_abort_task()
scsi: target: iscsi: Fix inconsistent debug message
scsi: target: iscsi: Fix login error when receiving
...
Pull networking updates from David Miller:
1) Support 6Ghz band in ath11k driver, from Rajkumar Manoharan.
2) Support UDP segmentation in code TSO code, from Eric Dumazet.
3) Allow flashing different flash images in cxgb4 driver, from Vishal
Kulkarni.
4) Add drop frames counter and flow status to tc flower offloading,
from Po Liu.
5) Support n-tuple filters in cxgb4, from Vishal Kulkarni.
6) Various new indirect call avoidance, from Eric Dumazet and Brian
Vazquez.
7) Fix BPF verifier failures on 32-bit pointer arithmetic, from
Yonghong Song.
8) Support querying and setting hardware address of a port function via
devlink, use this in mlx5, from Parav Pandit.
9) Support hw ipsec offload on bonding slaves, from Jarod Wilson.
10) Switch qca8k driver over to phylink, from Jonathan McDowell.
11) In bpftool, show list of processes holding BPF FD references to
maps, programs, links, and btf objects. From Andrii Nakryiko.
12) Several conversions over to generic power management, from Vaibhav
Gupta.
13) Add support for SO_KEEPALIVE et al. to bpf_setsockopt(), from Dmitry
Yakunin.
14) Various https url conversions, from Alexander A. Klimov.
15) Timestamping and PHC support for mscc PHY driver, from Antoine
Tenart.
16) Support bpf iterating over tcp and udp sockets, from Yonghong Song.
17) Support 5GBASE-T i40e NICs, from Aleksandr Loktionov.
18) Add kTLS RX HW offload support to mlx5e, from Tariq Toukan.
19) Fix the ->ndo_start_xmit() return type to be netdev_tx_t in several
drivers. From Luc Van Oostenryck.
20) XDP support for xen-netfront, from Denis Kirjanov.
21) Support receive buffer autotuning in MPTCP, from Florian Westphal.
22) Support EF100 chip in sfc driver, from Edward Cree.
23) Add XDP support to mvpp2 driver, from Matteo Croce.
24) Support MPTCP in sock_diag, from Paolo Abeni.
25) Commonize UDP tunnel offloading code by creating udp_tunnel_nic
infrastructure, from Jakub Kicinski.
26) Several pci_ --> dma_ API conversions, from Christophe JAILLET.
27) Add FLOW_ACTION_POLICE support to mlxsw, from Ido Schimmel.
28) Add SK_LOOKUP bpf program type, from Jakub Sitnicki.
29) Refactor a lot of networking socket option handling code in order to
avoid set_fs() calls, from Christoph Hellwig.
30) Add rfc4884 support to icmp code, from Willem de Bruijn.
31) Support TBF offload in dpaa2-eth driver, from Ioana Ciornei.
32) Support XDP_REDIRECT in qede driver, from Alexander Lobakin.
33) Support PCI relaxed ordering in mlx5 driver, from Aya Levin.
34) Support TCP syncookies in MPTCP, from Flowian Westphal.
35) Fix several tricky cases of PMTU handling wrt. briding, from Stefano
Brivio.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2056 commits)
net: thunderx: initialize VF's mailbox mutex before first usage
usb: hso: remove bogus check for EINPROGRESS
usb: hso: no complaint about kmalloc failure
hso: fix bailout in error case of probe
ip_tunnel_core: Fix build for archs without _HAVE_ARCH_IPV6_CSUM
selftests/net: relax cpu affinity requirement in msg_zerocopy test
mptcp: be careful on subflow creation
selftests: rtnetlink: make kci_test_encap() return sub-test result
selftests: rtnetlink: correct the final return value for the test
net: dsa: sja1105: use detected device id instead of DT one on mismatch
tipc: set ub->ifindex for local ipv6 address
ipv6: add ipv6_dev_find()
net: openvswitch: silence suspicious RCU usage warning
Revert "vxlan: fix tos value before xmit"
ptp: only allow phase values lower than 1 period
farsync: switch from 'pci_' to 'dma_' API
wan: wanxl: switch from 'pci_' to 'dma_' API
hv_netvsc: do not use VF device if link is down
dpaa2-eth: Fix passing zero to 'PTR_ERR' warning
net: macb: Properly handle phylink on at91sam9x
...
-----BEGIN PGP SIGNATURE-----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=oADH
-----END PGP SIGNATURE-----
Merge tag 'for-5.9/drivers-20200803' of git://git.kernel.dk/linux-block
Pull block driver updates from Jens Axboe:
- NVMe:
- ZNS support (Aravind, Keith, Matias, Niklas)
- Misc cleanups, optimizations, fixes (Baolin, Chaitanya, David,
Dongli, Max, Sagi)
- null_blk zone capacity support (Aravind)
- MD:
- raid5/6 fixes (ChangSyun)
- Warning fixes (Damien)
- raid5 stripe fixes (Guoqing, Song, Yufen)
- sysfs deadlock fix (Junxiao)
- raid10 deadlock fix (Vitaly)
- struct_size conversions (Gustavo)
- Set of bcache updates/fixes (Coly)
* tag 'for-5.9/drivers-20200803' of git://git.kernel.dk/linux-block: (117 commits)
md/raid5: Allow degraded raid6 to do rmw
md/raid5: Fix Force reconstruct-write io stuck in degraded raid5
raid5: don't duplicate code for different paths in handle_stripe
raid5-cache: hold spinlock instead of mutex in r5c_journal_mode_show
md: print errno in super_written
md/raid5: remove the redundant setting of STRIPE_HANDLE
md: register new md sysfs file 'uuid' read-only
md: fix max sectors calculation for super 1.0
nvme-loop: remove extra variable in create ctrl
nvme-loop: set ctrl state connecting after init
nvme-multipath: do not fall back to __nvme_find_path() for non-optimized paths
nvme-multipath: fix logic for non-optimized paths
nvme-rdma: fix controller reset hang during traffic
nvme-tcp: fix controller reset hang during traffic
nvmet: introduce the passthru Kconfig option
nvmet: introduce the passthru configfs interface
nvmet: Add passthru enable/disable helpers
nvmet: add passthru code to process commands
nvme: export nvme_find_get_ns() and nvme_put_ns()
nvme: introduce nvme_ctrl_get_by_path()
...
- Prepare for tasklet API modernization (Romain Perier, Allen Pais, Kees Cook)
-----BEGIN PGP SIGNATURE-----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=hb+e
-----END PGP SIGNATURE-----
Merge tag 'tasklets-v5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull tasklets API update from Kees Cook:
"These are the infrastructure updates needed to support converting the
tasklet API to something more modern (and hopefully for removal
further down the road).
There is a 300-patch series waiting in the wings to get set out to
subsystem maintainers, but these changes need to be present in the
kernel first. Since this has some treewide changes, I carried this
series for -next instead of paining Thomas with it in -tip, but it's
got his Ack.
This is similar to the timer_struct modernization from a while back,
but not nearly as messy (I hope). :)
- Prepare for tasklet API modernization (Romain Perier, Allen Pais,
Kees Cook)"
* tag 'tasklets-v5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
tasklet: Introduce new initialization API
treewide: Replace DECLARE_TASKLET() with DECLARE_TASKLET_OLD()
usb: gadget: udc: Avoid tasklet passing a global
- Add support for custom exception handlers, as required by BPF_PROBE_MEM.
- Add support for BPF_PROBE_MEM.
- Add trace events for idle enter / exit for the s390 specific idle
implementation.
- Remove unused zcore memmmap device.
- Remove unused "raw view" from s390 debug feature.
- AP bus + zcrypt device driver code refactoring.
- Provide cex4 cca sysfs attributes for cex3 for zcrypt device driver.
- Expose only minimal interface to walk physmem for mm/memblock. This
is a common code change and it has been agreed on with Mike Rapoport
and Andrew Morton that this can go upstream via the s390 tree.
- Rework of the s390 vmem/vmmemap code to allow for future memory hot
remove.
- Get rid of FORCE_MAX_ZONEORDER to finally allow for order-10
allocations again, instead of only order-8 allocations.
- Various small improvements and fixes.
-----BEGIN PGP SIGNATURE-----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=H0KX
-----END PGP SIGNATURE-----
Merge tag 's390-5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 updates from Heiko Carstens:
- Add support for function error injection.
- Add support for custom exception handlers, as required by
BPF_PROBE_MEM.
- Add support for BPF_PROBE_MEM.
- Add trace events for idle enter / exit for the s390 specific idle
implementation.
- Remove unused zcore memmmap device.
- Remove unused "raw view" from s390 debug feature.
- AP bus + zcrypt device driver code refactoring.
- Provide cex4 cca sysfs attributes for cex3 for zcrypt device driver.
- Expose only minimal interface to walk physmem for mm/memblock. This
is a common code change and it has been agreed on with Mike Rapoport
and Andrew Morton that this can go upstream via the s390 tree.
- Rework of the s390 vmem/vmmemap code to allow for future memory hot
remove.
- Get rid of FORCE_MAX_ZONEORDER to finally allow for order-10
allocations again, instead of only order-8 allocations.
- Various small improvements and fixes.
* tag 's390-5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (48 commits)
s390/vmemmap: coding style updates
s390/vmemmap: avoid memset(PAGE_UNUSED) when adding consecutive sections
s390/vmemmap: remember unused sub-pmd ranges
s390/vmemmap: fallback to PTEs if mapping large PMD fails
s390/vmem: cleanup empty page tables
s390/vmemmap: take the vmem_mutex when populating/freeing
s390/vmemmap: cleanup when vmemmap_populate() fails
s390/vmemmap: extend modify_pagetable() to handle vmemmap
s390/vmem: consolidate vmem_add_range() and vmem_remove_range()
s390/vmem: rename vmem_add_mem() to vmem_add_range()
s390: enable HAVE_FUNCTION_ERROR_INJECTION
s390/pci: clarify comment in s390_mmio_read/write
s390/time: improve comparison for tod steering
s390/time: select CLOCKSOURCE_VALIDATE_LAST_CYCLE
s390/time: use CLOCKSOURCE_MASK
s390/bpf: implement BPF_PROBE_MEM
s390/kernel: expand exception table logic to allow new handling options
s390/kernel: unify EX_TABLE* implementations
s390/mm: allow order 10 allocations
s390/mm: avoid trimming to MAX_ORDER
...
