update huawei ethernet driver maintainer from aviad to Bin luo
Signed-off-by: Luo bin <luobin9@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clean up after recent fixes, move address calculations
around and change the variable init, so that we can have
just one start_offset == end_offset check.
Make the check a little stricter to preserve the -EINVAL
error if requested start offset is larger than the region
itself.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Murali Karicheri says:
====================
am65-cpsw: add taprio/EST offload support
AM65 CPSW h/w supports Enhanced Scheduled Traffic (EST – defined
in P802.1Qbv/D2.2 that later got included in IEEE 802.1Q-2018)
configuration. EST allows express queue traffic to be scheduled
(placed) on the wire at specific repeatable time intervals. In
Linux kernel, EST configuration is done through tc command and
the taprio scheduler in the net core implements a software only
scheduler (SCH_TAPRIO). If the NIC is capable of EST configuration,
user indicate "flag 2" in the command which is then parsed by
taprio scheduler in net core and indicate that the command is to
be offloaded to h/w. taprio then offloads the command to the
driver by calling ndo_setup_tc() ndo ops. This patch implements
ndo_setup_tc() as well as other changes required to offload EST
configuration to CPSW h/w
For more details please refer patch 2/2.
This series is based on original work done by Ivan Khoronzhuk
<ivan.khoronzhuk@linaro.org> to add taprio offload support to
AM65 CPSW 2G.
1. Example configuration 3 Gates
ifconfig eth0 down
ethtool -L eth0 tx 3
ethtool --set-priv-flags eth0 p0-rx-ptype-rrobin off
ifconfig eth0 192.168.2.20
tc qdisc replace dev eth0 parent root handle 100 taprio \
num_tc 3 \
map 0 0 1 2 0 0 0 0 0 0 0 0 0 0 0 0 \
queues 1@0 1@1 1@2 \
base-time 0000 \
sched-entry S 4 125000 \
sched-entry S 2 125000 \
sched-entry S 1 250000 \
flags 2
2. Example configuration 8 Gates
ifconfig eth0 down
ethtool -L eth0 tx 8
ethtool --set-priv-flags eth0 p0-rx-ptype-rrobin off
ifconfig eth0 192.168.2.20
tc qdisc replace dev eth0 parent root handle 100 taprio \
num_tc 8 \
map 0 1 2 3 4 5 6 7 0 0 0 0 0 0 0 0 \
queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 \
base-time 0000 \
sched-entry S 80 125000 \
sched-entry S 40 125000 \
sched-entry S 20 125000 \
sched-entry S 10 125000 \
sched-entry S 08 125000 \
sched-entry S 04 125000 \
sched-entry S 02 125000 \
sched-entry S 01 125000 \
flags 2
Classify frames to particular priority using skbedit so that they land at
a specific queue in cpsw h/w which is Gated by the EST gate which opens based
on the sched-entry.
tc qdisc add dev eth0 clsact
In the below for example an iperf3 session with destination port 5007
will go through Q7.
tc filter add dev eth0 egress protocol ip prio 1 u32 match ip dport 5007 0xffff action skbedit priority 7
tc filter add dev eth0 egress protocol ip prio 1 u32 match ip dport 5006 0xffff action skbedit priority 6
tc filter add dev eth0 egress protocol ip prio 1 u32 match ip dport 5005 0xffff action skbedit priority 5
tc filter add dev eth0 egress protocol ip prio 1 u32 match ip dport 5004 0xffff action skbedit priority 4
tc filter add dev eth0 egress protocol ip prio 1 u32 match ip dport 5003 0xffff action skbedit priority 3
tc filter add dev eth0 egress protocol ip prio 1 u32 match ip dport 5002 0xffff action skbedit priority 2
tc filter add dev eth0 egress protocol ip prio 1 u32 match ip dport 5001 0xffff action skbedit priority 1
iperf3 -c 192.168.2.10 -u -l1470 -b32M -t1 -p 5007
Testing was done by capturing frames at the PC using wireshark and checking for
the bust interval or cycle time of UDP frames with a specific port number.
Verified that the distance between first frame of a burst (cycle-time) is 1
milli second and burst duration is within 125 usec based on the received packet
timestamp shown in wireshark packet display.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
AM65 CPSW h/w supports Enhanced Scheduled Traffic (EST – defined
in P802.1Qbv/D2.2 that later got included in IEEE 802.1Q-2018)
configuration. EST allows express queue traffic to be scheduled
(placed) on the wire at specific repeatable time intervals. In
Linux kernel, EST configuration is done through tc command and
the taprio scheduler in the net core implements a software only
scheduler (SCH_TAPRIO). If the NIC is capable of EST configuration,
user indicate "flag 2" in the command which is then parsed by
taprio scheduler in net core and indicate that the command is to
be offloaded to h/w. taprio then offloads the command to the
driver by calling ndo_setup_tc() ndo ops. This patch implements
ndo_setup_tc() to offload EST configuration to CPSW h/w.
Currently driver supports only SetGateStates operation. EST
operates on a repeating time interval generated by the CPTS EST
function generator. Each Ethernet port has a global EST fetch
RAM that can be configured as 2 buffers, each of 64 locations
or one large buffer of 128 locations. In 2 buffer configuration,
a ping pong mechanism is used to hold the active schedule (oper)
in one buffer and new (admin) command in the other. Each 22-bit
fetch command consists of a 14-bit fetch count (14 MSB’s) and an
8-bit priority fetch allow (8 LSB’s) that will be applied for the
fetch count time in wireside clocks. Driver process each of the
sched-entry in the offload command and update the fetch RAM.
Driver configures duration in sched-entry into the fetch count
and Gate mask into the priority fetch bits of the RAM. Then
configures the CPTS EST function generator to activate the
schedule. Currently driver supports only 2 buffer configuration
which means driver supports a max cycle time of ~8 msec.
CPSW supports a configurable number of priority queues (up to 8)
and needs to be switched to this mode from the default round
robin mode before EST can be offloaded. User configures
these through ethtool commands (-L for changing number of
queues and --set-priv-flags to disable round robin mode).
Driver doesn't enable EST if pf_p0_rx_ptype_rrobin privat flag
is set. The flag is common for all ports, and so can't be just
overridden by taprio configuration w/o user involvement.
Command fails if pf_p0_rx_ptype_rrobin is already set in the
driver.
Scheds (commands) configuration depends on interface speed so
driver translates the duration to the fetch count based on
link speed. Each schedule can be constructed with several
command entries in fetch RAM depending on interval. For example
if each sched has timer interval < ~130us on 1000 Mb link then
each sched consumes one command and have 1:1 mapping. When
Ethernet link goes down, driver purge the configuration if link
is down for more than 1 second.
The patch allows to update the timer and scheds memory only if it's
really needed, and skip cases required the user to stop timer by
configuring only shceds memory.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TAPRIO/EST offload support in CPSW2G requires EST scheduler
function enabled in CPTS. So this patch add a function to
set cycle time for EST scheduler. It also add a function for
getting time in ns of PHC clock for taprio qdisc configuration.
Mostly to verify if timer update is needed or to get actual
state of oper/admin schedule.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Igor Russkikh says:
====================
net: qed/qede: critical hw error handling
FastLinQ devices as a complex systems may observe various hardware
level error conditions, both severe and recoverable.
Driver is able to detect and report this, but so far it only did
trace/dmesg based reporting.
Here we implement an extended hw error detection, service task
handler captures a dump for the later analysis.
I also resubmit a patch from Denis Bolotin on tx timeout handler,
addressing David's comment regarding recovery procedure as an extra
reaction on this event.
v2:
Removing the patch with ethtool dump and udev magic. Its quite isolated,
I'm working on devlink based logic for this separately.
v1:
https://patchwork.ozlabs.org/project/netdev/cover/cover.1588758463.git.irusskikh@marvell.com/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
On some adjacent code, fix bad code formatting
Signed-off-by: Ariel Elior <ariel.elior@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MCP may signal driver about generic critical failure.
Driver has to collect mdump information (get_retain),
it pushes that to logs and triggers generic notification on
"hardware attention" event.
Signed-off-by: Ariel Elior <ariel.elior@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fan failure is sent by firmware, driver reacts on this error with
newly introduced notification path. It will collect dump and shut down
the device to prevent physical breakage
Signed-off-by: Ariel Elior <ariel.elior@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upon tx timeout detection we do disable carrier and print TX queue
info on TX timeout. We then raise hw error condition and trigger
service task to handle this.
This handler will capture extra debug info and then optionally
trigger recovery procedure to try restore function.
Signed-off-by: Denis Bolotin <dbolotin@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver has an ability to initiate a recovery process as a reaction to
detected errors. But the codepath (recovery_process) was disabled and
never active.
Here we add ethtool private flag to allow user have the recovery
procedure activated.
We still do not enable this by default though, since in some configurations
this is not desirable. E.g. this may impact other PFs/VFs.
Signed-off-by: Ariel Elior <ariel.elior@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On different hardware events we have to respond differently,
on some of hardware indications hw attention (error condition)
should be cleared by the driver to continue normal functioning.
Here we introduce attention clear flags, and put them on some
important events (in aeu_descs).
Signed-off-by: Ariel Elior <ariel.elior@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thats probably a legacy code had double declaration of some fields.
Cleanup this, removing copy and fixing references.
Signed-off-by: Ariel Elior <ariel.elior@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On various critical errors, notification handler should also report
the err information into the management firmware.
MFW can interact with server/motherboard backend agents - these are
used by server manufacturers to monitor server HW health.
Thus, it is important for driver to report on any faulty conditions
Signed-off-by: Ariel Elior <ariel.elior@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a number of critical places not only debug trace should be printed,
but the appropriate hw error condition should be raised and error
handling/recovery should start.
Introduce our new qed_hw_err_notify invocation in these places to
record and indicate critical error conditions in hardware.
Signed-off-by: Ariel Elior <ariel.elior@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qede (ethernet level driver) registers a callback handler.
This handler maintains eth dev state flags/bits to track error processing.
It implements in place processing part for nonsleeping context (WARN_ON
trigger), and a deferred (delayed work) part which triggers recovery
process for recoverable errors.
In later patches this atomic handler will come with more meat.
We introduce err_flags on ethdevice structure, its being used to record
error handling properties.
Signed-off-by: Ariel Elior <ariel.elior@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here we introduce qed device error tracking flags and error types.
qed_hw_err_notify is an entrace point to report errors.
It'll notify higher level drivers (qede/qedr/etc) to handle and recover
the error.
List of posible errors comes from hardware interfaces, but could be
extended in future.
Signed-off-by: Ariel Elior <ariel.elior@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Huazhong Tan says:
====================
net: hns3: add some cleanups for -next
This patchset adds some cleanups for the HNS3 ethernet driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The skb_has_frag_list() in hns3_nic_net_xmit() is redundant, since
skb_walk_frags() includes this checking implicitly.
Reported-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some macros defined in hns3_enet.h, but not used in
anywhere.
Reported-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When handling HCLGE_MBX_GET_LINK_STATUS, PF will return the link
status to the VF, so the error log of hclge_get_link_info() is
incorrect.
Reported-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since hclge_get_cfg() already has error print, so hclge_configure()
should not print error when calling hclge_get_cfg() fail.
Reported-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch modifies some incorrect spelling.
Reported-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a MAC address was passed via the device tree node for the r8152
device, use it and fall back to reading from EEPROM otherwise. This is
useful for devices where the r8152 EEPROM was not programmed with a
valid MAC address, or if users want to explicitly set a MAC address in
the bootloader and pass that to the kernel.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flower tests used to create ingress filter with specified parent qdisc
"parent ffff:" but dump them on "ingress". With recent commit that fixed
tcm_parent handling in dump those are not considered same parent anymore,
which causes iproute2 tc to emit additional "parent ffff:" in first line of
filter dump output. The change in output causes filter match in tests to
fail.
Prevent parent qdisc output when dumping filters in flower tests by always
correctly specifying "ingress" parent both when creating and dumping
filters.
Fixes: a7df4870d7 ("net_sched: fix tcm_parent in tc filter dump")
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, setting a bridge's self PVID to other value and deleting
the default VID 1 renders untagged ports of that VLAN unable to talk to
the CPU port:
bridge vlan add dev br0 vid 2 pvid untagged self
bridge vlan del dev br0 vid 1 self
bridge vlan add dev sw0p0 vid 2 pvid untagged
bridge vlan del dev sw0p0 vid 1
# br0 cannot send untagged frames out of sw0p0 anymore
That is because the CPU port is set to security mode and its PVID is
still 1, and untagged frames are dropped due to VLAN member violation.
Set the CPU port to fallback mode so untagged frames can pass through.
Fixes: 83163f7dca ("net: dsa: mediatek: add VLAN support for MT7530")
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some PHYs connected to this ethernet hardware support the WoL feature.
But when WoL is enabled and the machine is powered off, the PHY remains
waiting for a magic packet at max speed (i.e. 1Gbps), which is a waste of
energy.
Slow down the PHY speed before stopping the ethernet if WoL is enabled,
and save some energy while the machine is powered off or sleeping.
Tested using an Armada 370 based board (LS421DE) equipped with a Marvell
88E1518 PHY.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently pointer table is being dereferenced on a null check of
table->must_restore_filters before it is being null checked, leading
to a potential null pointer dereference issue. Fix this by null
checking table before dereferencing it when checking for a null
table->must_restore_filters.
Addresses-Coverity: ("Dereference before null check")
Fixes: e4fe938cff ("sfc: move 'must restore' flags out of ef10-specific nic_data")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The AR8031/AR8033 and the AR8035 support cable diagnostics. Adding
driver support is straightforward, so lets add it.
The PHY just do one pair at a time, so we have to start the test four
times. The cable_test_get_status() can block and therefore we can just
busy poll the test completion and continue with the next pair until we
are done.
The time delta counter seems to run at 125MHz which just gives us a
resolution of about 82.4cm per tick.
100m cable, A/B/C/D open:
Cable test started for device eth0.
Cable test completed for device eth0.
Pair: Pair A, result: Open Circuit
Pair: Pair A, fault length: 107.94m
Pair: Pair B, result: Open Circuit
Pair: Pair B, fault length: 104.64m
Pair: Pair C, result: Open Circuit
Pair: Pair C, fault length: 105.47m
Pair: Pair D, result: Open Circuit
Pair: Pair D, fault length: 107.94m
1m cable, A/B connected, C shorted, D open:
Cable test started for device eth0.
Cable test completed for device eth0.
Pair: Pair A, result: OK
Pair: Pair B, result: OK
Pair: Pair C, result: Short within Pair
Pair: Pair C, fault length: 0.82m
Pair: Pair D, result: Open Circuit
Pair: Pair D, fault length: 0.82m
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While do_ipv6_getsockopt does not call the high-level recvmsg helper,
the msghdr eventually ends up being passed to put_cmsg anyway, and thus
needs msg_control_is_user set to the proper value.
Fixes: 1f466e1f15 ("net: cleanly handle kernel vs user buffers for ->msg_control")
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Walle says:
====================
net: phy: broadcom: cable tester support
Add cable tester support for the Broadcom PHYs. Support for it was
developed on a BCM54140 Quad PHY which RDB register access.
If there is a link partner the results are not as good as with an open
cable. I guess we could retry if the measurement until all pairs had at
least one valid result.
changes since v1:
- added Reviewed-by: tags
- removed "div by 2" for cross shorts, just mention it in the commit
message. The results are inconclusive if the tests are repeated. So
just report the length as is for now.
- fixed typo in commit message
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the generic cable tester functions from bcm-phy-lib to add cable
tester support.
100m cable, A/B/C/D open:
Cable test started for device eth0.
Cable test completed for device eth0.
Pair: Pair A, result: Open Circuit
Pair: Pair B, result: Open Circuit
Pair: Pair C, result: Open Circuit
Pair: Pair D, result: Open Circuit
Pair: Pair A, fault length: 106.60m
Pair: Pair B, fault length: 103.32m
Pair: Pair C, fault length: 104.96m
Pair: Pair D, fault length: 106.60m
1m cable, A/B connected, pair C shorted, D open:
Cable test started for device eth0.
Cable test completed for device eth0.
Pair: Pair A, result: OK
Pair: Pair B, result: OK
Pair: Pair C, result: Short within Pair
Pair: Pair D, result: Open Circuit
Pair: Pair C, fault length: 0.82m
Pair: Pair D, fault length: 1.64m
1m cable, A/B connected, pair C shorted with D:
Cable test started for device eth0.
Cable test completed for device eth0.
Pair: Pair A, result: OK
Pair: Pair B, result: OK
Pair: Pair C, result: Short to another pair
Pair: Pair D, result: Short to another pair
Pair: Pair C, fault length: 1.64m
Pair: Pair D, fault length: 1.64m
The granularity of the length measurement seems to be 82cm.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most modern broadcom PHYs support ECD (enhanced cable diagnostics). Add
support for it in the bcm-phy-lib so they can easily be used in the PHY
driver.
There are two access methods for ECD: legacy by expansion registers and
via the new RDB registers which are exclusive. Provide functions in two
variants where the PHY driver can choose from. To keep things simple for
now, we just switch the register access to expansion registers in the
RDB variant for now. On the flipside, we have to keep a bus lock to
prevent any other non-legacy access on the PHY.
The results of the intra-pair tests are inconclusive (at least for the
BCM54140). Most of the times half the length is reported but sometimes
the length is correct.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the convenience function to do a read-modify-write. This has the
additional benefit of saving one write to the selection register.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add helper to read and write expansion registers without taking the mdio
lock.
Please note, that this changes the semantics of the read and write.
Before there was no lock between selecting the expansion register and
the actual read/write. This may lead to access failures if there are
parallel accesses. Instead take the bus lock during the whole access
cycle.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add initial cable testing support.
This PHY needs only 100usec for this test and it is recommended to run it
before the link is up. For now, provide at least ethtool support, so it
can be tested by more developers.
This patch was tested with TJA1102 PHY with following results:
- No cable, is detected as open
- 1m cable, with no connected other end and detected as open
- a 40m cable (out of spec, max lenght should be 15m) is detected as OK.
Current patch do not provide polarity test support. This test would
indicate not proper wire connection, where "+" wire of main phy is
connected to the "-" wire of the link partner.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code had historically been ignoring these errors, and my recent
refactoring changed that, which broke ssh in some setups.
Fixes: 2618d530dd ("net/scm: cleanup scm_detach_fds")
Reported-by: Ido Schimmel <idosch@idosch.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Ido Schimmel <idosch@mellanox.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Martin Blumenstingl says:
====================
dwmac-meson8b Ethernet RX delay configuration
The Ethernet TX performance has been historically bad on Meson8b and
Meson8m2 SoCs because high packet loss was seen. I found out that this
was related (yet again) to the RGMII TX delay configuration.
In the process of discussing the big picture (and not just a single
patch) [0] with Andrew I discovered that the IP block behind the
dwmac-meson8b driver actually seems to support the configuration of the
RGMII RX delay (at least on the Meson8b SoC generation).
Since I sent the first RFC I got additional documentation from Jianxin
(many thanks!). Also I have discovered some more interesting details:
- Meson8b Odroid-C1 requires an RX delay (by either the PHY or the MAC)
Based on the vendor u-boot code (not upstream) I assume that it will
be the same for all Meson8b and Meson8m2 boards
- Khadas VIM2 seems to have the RX delay built into the PCB trace
length. When I enable the RX delay on the PHY or MAC I can't get any
data through. I expect that we will have the same situation on all
GXBB, GXM, AXG, G12A, G12B and SM1 boards. Further clarification is
needed here though (since I can't visually see these lengthened
traces on the PCB). This will be done before sending patches for
these boards.
Dependencies for this series:
There is a soft dependency for patch #2 on commit f22531438f
"dt-bindings: net: dwmac: increase 'maxItems' for 'clocks',
'clock-names' properties" which is currently in Rob's -next tree.
That commit is needed to make the dt-bindings schema validation
pass for patch #2. That patch has been for ~4 weeks in Robs tree,
so I assume that is not going to be dropped.
Changes since RFC v2 at [2]:
- dropped $ref: /schemas/types.yaml#definitions/uint32 from the
"amlogic,rx-delay-ns" in patch #1 ("Don't need to define the
type when in standard units." says Rob - thanks, I learned
something new). Also use "default: 0" for for this property
instead of explaining it in the description text.
- added a note to the cover-letter about a hidden dependency for
dt-binding schema validation in patch #2
- Added Andrew's Reviewed-by to patches 1-7. Thank you again for
the quick and detailed reviews, I appreciate this!
- error out if the (optional) timing-adjustment clock is missing
but we're asked to enable the RGMII RX delay. The MAC won't
work in this specific case and either the RX delay has to be
provided by the PHY or the timing-adjustment clock has to be
added.
- dropped the dts patches (#9-11) which were only added to give
an overview how this is going to be used. those will be sent
separately
- dropped the RFC prefix
Changes since RFC v1 at [1]:
- add support for the timing adjustment clock input (dt-bindings and
in the driver) thanks to the input from the unnamed Ethernet engineer
at Amlogic. This is the missing link between the fclk_div2 clock and
the Ethernet controller on Meson8b (no traffic would flow if that
clock was disabled)
- add support fot the amlogic,rx-delay-ns property. The only supported
values so far are 0ns and 2ns. The registers seem to allow more
precise timing adjustments, but I could not make that work so far.
- add more register documentation (for the new RX delay bits) and
unified the placement of existing register documentation. Again,
thanks to Jianxin and the unnamed Ethernet engineer at Amlogic
- DO NOT MERGE: .dts patches to show the conversion of the Meson8b
and Meson8m2 boards to "rgmii-id". I didn't have time for all arm64
patches yet, but these will switch to phy-mode = "rgmii-txid" with
amlogic,rx-delay-ns = <0> (because the delay seems to be provided by
the PCB trace length).
[0] https://patchwork.kernel.org/patch/11309891/
[1] https://patchwork.kernel.org/cover/11310719/
[2] https://patchwork.kernel.org/cover/11518257/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Configure the PRG_ETH0_ADJ_* bits to enable or disable the RX delay
based on the various RGMII PHY modes. For now the only supported RX
delay settings are:
- disabled, use for example for phy-mode "rgmii-id"
- 0ns - this is treated identical to "disabled", used for example on
boards where the PHY provides 2ns TX delay and the PCB trace length
already adds 2ns RX delay
- 2ns - for whenever the PHY cannot add the RX delay and the traces on
the PCB don't add any RX delay
Disabling the RX delay (in case u-boot enables it, which is the case
for example on Meson8b Odroid-C1) simply means that PRG_ETH0_ADJ_ENABLE,
PRG_ETH0_ADJ_SETUP, PRG_ETH0_ADJ_DELAY and PRG_ETH0_ADJ_SKEW should be
disabled (just disabling PRG_ETH0_ADJ_ENABLE may be enough, since that
disables the whole re-timing logic - but I find it makes more sense to
clear the other bits as well since they depend on that setting).
u-boot on Odroid-C1 uses the following steps to enable a 2ns RX delay:
- enabling enabling the timing adjustment clock
- enabling the timing adjustment logic by setting PRG_ETH0_ADJ_ENABLE
- setting the PRG_ETH0_ADJ_SETUP bit
The documentation for the PRG_ETH0_ADJ_DELAY and PRG_ETH0_ADJ_SKEW
registers indicates that we can even set different RX delays. However,
I could not find out how this works exactly, so for now we only support
a 2ns RX delay using the exact same way that Odroid-C1's u-boot does.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The timing adjustment clock will need similar logic as the RGMII clock:
It has to be enabled in the driver conditionally and when the driver is
unloaded it should be disabled again. Extract the existing code for the
RGMII clock into a new function so it can be re-used.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PRG_ETHERNET registers have a built-in timing adjustment circuit
which can provide the RX delay in RGMII mode. This is driven by an
external (to this IP, but internal to the SoC) clock input. Fetch this
clock as optional (even though it's there on all supported SoCs) since
we just learned about it and existing .dtbs don't specify it.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PRG_ETH0_ADJ_* are used for applying the RGMII RX delay. The public
datasheets only have very limited description for these registers, but
Jianxin Pan provided more detailed documentation from an (unnamed)
Amlogic engineer. Add the PRG_ETH0_ADJ_* bits along with the improved
description.
Suggested-by: Jianxin Pan <jianxin.pan@amlogic.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the documentation for the TX delay above the PRG_ETH0_TXDLY_MASK
definition. Future commits will add more registers also with
documentation above their register bit definitions. Move the existing
comment so it will be consistent with the upcoming changes.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use FIELD_PREP() to shift a value to the correct offset based on a
bitmask instead of open-coding the logic.
No functional changes.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PRG_ETHERNET registers can add an RX delay in RGMII mode. This
requires an internal re-timing circuit whose input clock is called
"timing adjustment clock". Document this clock input so the clock can be
enabled as needed.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PRG_ETHERNET registers on Meson8b and newer SoCs can add an RX
delay. Add a property with the known supported values so it can be
configured according to the board layout.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2020-05-13
Here's a second attempt at a bluetooth-next pull request which
supercedes the one dated 2020-05-09. This should have the issues
discovered by Jakub fixed.
- Add support for Intel Typhoon Peak device (8087:0032)
- Add device tree bindings for Realtek RTL8723BS device
- Add device tree bindings for Qualcomm QCA9377 device
- Add support for experimental features configuration through mgmt
- Add driver hook to prevent wake from suspend
- Add support for waiting for L2CAP disconnection response
- Multiple fixes & cleanups to the btbcm driver
- Add support for LE scatternet topology for selected devices
- A few other smaller fixes & cleanups
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Xiaoliang Yang says:
====================
net: dsa: felix: tc taprio and CBS offload support
This patch series support tc taprio and CBS hardware offload according
to IEEE 802.1Qbv and IEEE-802.1Qav on VSC9959.
v1->v2 changes:
- Move port_qos_map_init() function to be common felix codes.
- Keep const for dsa_switch_ops structs, add felix_port_setup_tc
function to call port_setup_tc of felix.info.
- fix code style for cbs_set, rename variables.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
VSC9959 hardware support the Credit Based Shaper(CBS) which part
of the IEEE-802.1Qav. This patch support sch_cbs set for VSC9959.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
