portdrv_pci.c doesn't use anything from <linux/pci-aspm.h>. Remove the
include of it. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some PCIe features (AER, DPC, hotplug, PME) can be managed by either the
platform firmware or the OS, so the host bridge driver may have to request
permission from the platform before using them. On ACPI systems, this is
done by negotiate_os_control() in acpi_pci_root_add().
The PCIe port driver later uses pcie_port_platform_notify() and
pcie_port_acpi_setup() to figure out whether it can use these features.
But all we need is a single bit for each service, so these interfaces are
needlessly complicated.
Simplify this by adding bits in the struct pci_host_bridge to show when the
OS has permission to use each feature:
+ unsigned int native_aer:1; /* OS may use PCIe AER */
+ unsigned int native_hotplug:1; /* OS may use PCIe hotplug */
+ unsigned int native_pme:1; /* OS may use PCIe PME */
These are set when we create a host bridge, and the host bridge driver can
clear the bits corresponding to any feature the platform doesn't want us to
use.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
No driver registers for PCIE_PORT_SERVICE_VC, so remove it.
This removes the VC "service" files from /sys/bus/pci_express/devices,
e.g., 0000:07:00.0:pcie108, 0000:08:04.0:pcie208 (all the files that
contained "8" as the last digit of the "pcieXXX" part). The port driver
created these files for PCIe port devices that have a VC Capability.
Since this reduces PCIE_PORT_DEVICE_MAXSERVICES and moves DPC down into the
spot where VC used to be, the DPC sysfs files will now be named "pcieXX8".
I don't think there's anything useful userspace can do with those files, so
I hope nobody cares about these filenames.
There is no VC driver that calls pcie_port_service_register(), so there
never was a /sys/bus/pci_express/drivers/vc directory.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
The pcie_port_bus_type must be registered before drivers that depend on it
can be registered. Those drivers include:
pcied_init() # PCIe native hotplug driver
aer_service_init() # AER driver
dpc_service_init() # DPC driver
pcie_pme_service_init() # PME driver
Previously we registered pcie_port_bus_type from pcie_portdrv_init(), a
device_initcall. The callers of pcie_port_service_register() (above) are
also device_initcalls. This is fragile because the device_initcall
ordering depends on link order, which is not explicit.
Register pcie_port_bus_type from pci_driver_init() along with pci_bus_type.
This removes the link order dependency between portdrv and the pciehp, AER,
DPC, and PCIe PME drivers.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
The "pcie_ports=compat" kernel parameter sets pcie_ports_disabled, which is
intended to disable the PCIe port driver. But even when it was disabled,
we registered pcie_portdriver so we could work around a BIOS PME issue (see
fe31e69740 ("PCI/PCIe: Clear Root PME Status bits early during system
resume")).
Registering the driver meant that the pcie_portdrv_probe() path called
pci_enable_device(), pci_save_state(), pm_runtime_set_autosuspend_delay(),
pm_runtime_use_autosuspend(), etc., even when the driver was disabled.
We've since moved the BIOS PME workaround from the port driver to the core,
so stop registering the PCIe port driver in compat mode.
This means "pcie_ports=compat" will now be basically the same as turning
off CONFIG_PCIEPORTBUS completely.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Remove pointless comments that tell us the file name, remove blank line
comments, follow multi-line comment conventions. No functional change
intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Indent things so they line up neatly and remove extra blank lines and
superfluous comments. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
fe31e69740 ("PCI/PCIe: Clear Root PME Status bits early during system
resume") added a .resume_noirq() callback to the PCIe port driver to clear
the PME Status bit during resume to work around a BIOS issue.
The BIOS evidently enabled PME interrupts for ACPI-based runtime wakeups
but did not clear the PME Status bit during resume, which meant PMEs after
resume did not trigger interrupts because PME Status did not transition
from cleared to set.
The fix was in the PCIe port driver, so it worked when CONFIG_PCIEPORTBUS
was set. But I think we *always* want the fix because the platform may use
PME interrupts even if Linux is built without the PCIe port driver.
Move the fix from the port driver to the PCI core so we can work around
this "PME doesn't work after waking from a sleep state" issue regardless of
CONFIG_PCIEPORTBUS.
[bhelgaas: folded in warning fix from Arnd Bergmann <arnd@arndb.de>:
https://lkml.kernel.org/r/20180328134747.2062348-1-arnd@arndb.de]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Move pcie_clear_root_pme_status() from the port driver to the PCI core so
it will be available even when the port driver isn't present. No
functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
pcieport_if.h contained the interfaces to register port service driver,
e.g., pcie_port_service_register(). portdrv.h contained internal data
structures of the port driver.
I don't think it's worth keeping those files separate, since both headers
and their users are all inside the PCI core.
Merge pcieport_if.h directly in drivers/pci/pcie/portdrv.h and update the
users to include that instead.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Previously we emitted a warning if we tried to configure common clock mode
the link was already configured to common clock mode by the UEFI BIOS.
Bail out silently in that case instead of emitting the warning:
pci 0004:00:00.0: ASPM: Could not configure common clock
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
aspm_calc_l1ss_info() computes l1_2_threshold in microseconds as:
l1_2_threshold = 2 + 4 + t_common_mode + t_power_on;
where t_common_mode is at most 255us:
PCI_L1SS_CAP_CM_RESTORE_TIME 0x0000ff00 <-- 8 bits; <256us
and t_power_on is at most 31 * 100us = 3100us:
PCI_L1SS_CAP_P_PWR_ON_VALUE 0x00f80000 <-- 5 bits; <32
PCI_L1SS_CAP_P_PWR_ON_SCALE 0x00030000 <-- *2us, *10us, or *100us
So l1_2_threshold is at most 2 + 4 + 255 + 3100 = 3361, which means
threshold_ns is at most 3361 * 1000 = 3361000, which easily fits in a
u32.
Declare threshold_ns as u32, not u64. This fixes a Coverity warning.
Addresses-Coverity-ID: 1462501
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Move pcieport_if.h from include/linux to drivers/pci/pcie/pcieport_if.h
because the interfaces there are only used by the PCI core.
Replace all uses of #include<linux/pcieport_if.h> with relative paths to
the new file location, e.g., #include "../pcieport_if.h"
Signed-off-by: Frederick Lawler <fred@fredlawl.com>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ttq9
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- skip AER driver error recovery callbacks for correctable errors
reported via ACPI APEI, as we already do for errors reported via the
native path (Tyler Baicar)
- fix DPC shared interrupt handling (Alex Williamson)
- print full DPC interrupt number (Keith Busch)
- enable DPC only if AER is available (Keith Busch)
- simplify DPC code (Bjorn Helgaas)
- calculate ASPM L1 substate parameter instead of hardcoding it (Bjorn
Helgaas)
- enable Latency Tolerance Reporting for ASPM L1 substates (Bjorn
Helgaas)
- move ASPM internal interfaces out of public header (Bjorn Helgaas)
- allow hot-removal of VGA devices (Mika Westerberg)
- speed up unplug and shutdown by assuming Thunderbolt controllers
don't support Command Completed events (Lukas Wunner)
- add AtomicOps support for GPU and Infiniband drivers (Felix Kuehling,
Jay Cornwall)
- expose "ari_enabled" in sysfs to help NIC naming (Stuart Hayes)
- clean up PCI DMA interface usage (Christoph Hellwig)
- remove PCI pool API (replaced with DMA pool) (Romain Perier)
- deprecate pci_get_bus_and_slot(), which assumed PCI domain 0 (Sinan
Kaya)
- move DT PCI code from drivers/of/ to drivers/pci/ (Rob Herring)
- add PCI-specific wrappers for dev_info(), etc (Frederick Lawler)
- remove warnings on sysfs mmap failure (Bjorn Helgaas)
- quiet ROM validation messages (Alex Deucher)
- remove redundant memory alloc failure messages (Markus Elfring)
- fill in types for compile-time VGA and other I/O port resources
(Bjorn Helgaas)
- make "pci=pcie_scan_all" work for Root Ports as well as Downstream
Ports to help AmigaOne X1000 (Bjorn Helgaas)
- add SPDX tags to all PCI files (Bjorn Helgaas)
- quirk Marvell 9128 DMA aliases (Alex Williamson)
- quirk broken INTx disable on Ceton InfiniTV4 (Bjorn Helgaas)
- fix CONFIG_PCI=n build by adding dummy pci_irqd_intx_xlate() (Niklas
Cassel)
- use DMA API to get MSI address for DesignWare IP (Niklas Cassel)
- fix endpoint-mode DMA mask configuration (Kishon Vijay Abraham I)
- fix ARTPEC-6 incorrect IS_ERR() usage (Wei Yongjun)
- add support for ARTPEC-7 SoC (Niklas Cassel)
- add endpoint-mode support for ARTPEC (Niklas Cassel)
- add Cadence PCIe host and endpoint controller driver (Cyrille
Pitchen)
- handle multiple INTx status bits being set in dra7xx (Vignesh R)
- translate dra7xx hwirq range to fix INTD handling (Vignesh R)
- remove deprecated Exynos PHY initialization code (Jaehoon Chung)
- fix MSI erratum workaround for HiSilicon Hip06/Hip07 (Dongdong Liu)
- fix NULL pointer dereference in iProc BCMA driver (Ray Jui)
- fix Keystone interrupt-controller-node lookup (Johan Hovold)
- constify qcom driver structures (Julia Lawall)
- rework Tegra config space mapping to increase space available for
endpoints (Vidya Sagar)
- simplify Tegra driver by using bus->sysdata (Manikanta Maddireddy)
- remove PCI_REASSIGN_ALL_BUS usage on Tegra (Manikanta Maddireddy)
- add support for Global Fabric Manager Server (GFMS) event to
Microsemi Switchtec switch driver (Logan Gunthorpe)
- add IDs for Switchtec PSX 24xG3 and PSX 48xG3 (Kelvin Cao)
* tag 'pci-v4.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (140 commits)
PCI: cadence: Add EndPoint Controller driver for Cadence PCIe controller
dt-bindings: PCI: cadence: Add DT bindings for Cadence PCIe endpoint controller
PCI: endpoint: Fix EPF device name to support multi-function devices
PCI: endpoint: Add the function number as argument to EPC ops
PCI: cadence: Add host driver for Cadence PCIe controller
dt-bindings: PCI: cadence: Add DT bindings for Cadence PCIe host controller
PCI: Add vendor ID for Cadence
PCI: Add generic function to probe PCI host controllers
PCI: generic: fix missing call of pci_free_resource_list()
PCI: OF: Add generic function to parse and allocate PCI resources
PCI: Regroup all PCI related entries into drivers/pci/Makefile
PCI/DPC: Reformat DPC register definitions
PCI/DPC: Add and use DPC Status register field definitions
PCI/DPC: Squash dpc_rp_pio_get_info() into dpc_process_rp_pio_error()
PCI/DPC: Remove unnecessary RP PIO register structs
PCI/DPC: Push dpc->rp_pio_status assignment into dpc_rp_pio_get_info()
PCI/DPC: Squash dpc_rp_pio_print_error() into dpc_rp_pio_get_info()
PCI/DPC: Make RP PIO log size check more generic
PCI/DPC: Rename local "status" to "dpc_status"
PCI/DPC: Squash dpc_rp_pio_print_tlp_header() into dpc_rp_pio_print_error()
...
Highlights:
- Enable support for memory protection keys aka "pkeys" on Power7/8/9 when
using the hash table MMU.
- Extend our interrupt soft masking to support masking PMU interrupts as well
as "normal" interrupts, and then use that to implement local_t for a ~4x
speedup vs the current atomics-based implementation.
- A new driver "ocxl" for "Open Coherent Accelerator Processor Interface
(OpenCAPI)" devices.
- Support for new device tree properties on PowerVM to describe hotpluggable
memory and devices.
- Add support for CLOCK_{REALTIME/MONOTONIC}_COARSE to the 64-bit VDSO.
- Freescale updates from Scott:
"Contains fixes for CPM GPIO and an FSL PCI erratum workaround, plus a
minor cleanup patch."
As well as quite a lot of other changes all over the place, and small fixes and
cleanups as always.
Thanks to:
Alan Modra, Alastair D'Silva, Alexey Kardashevskiy, Alistair Popple, Andreas
Schwab, Andrew Donnellan, Aneesh Kumar K.V, Anju T Sudhakar, Anshuman
Khandual, Anton Blanchard, Arnd Bergmann, Balbir Singh, Benjamin
Herrenschmidt, Bhaktipriya Shridhar, Bryant G. Ly, Cédric Le Goater,
Christophe Leroy, Christophe Lombard, Cyril Bur, David Gibson, Desnes A. Nunes
do Rosario, Dmitry Torokhov, Frederic Barrat, Geert Uytterhoeven, Guilherme G.
Piccoli, Gustavo A. R. Silva, Gustavo Romero, Ivan Mikhaylov, Joakim
Tjernlund, Joe Perches, Josh Poimboeuf, Juan J. Alvarez, Julia Cartwright,
Kamalesh Babulal, Madhavan Srinivasan, Mahesh Salgaonkar, Mathieu Malaterre,
Michael Bringmann, Michael Hanselmann, Michael Neuling, Nathan Fontenot,
Naveen N. Rao, Nicholas Piggin, Paul Mackerras, Philippe Bergheaud, Ram Pai,
Russell Currey, Santosh Sivaraj, Scott Wood, Seth Forshee, Simon Guo, Stewart
Smith, Sukadev Bhattiprolu, Thiago Jung Bauermann, Vaibhav Jain, Vasyl
Gomonovych.
-----BEGIN PGP SIGNATURE-----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=3rYn
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Highlights:
- Enable support for memory protection keys aka "pkeys" on Power7/8/9
when using the hash table MMU.
- Extend our interrupt soft masking to support masking PMU interrupts
as well as "normal" interrupts, and then use that to implement
local_t for a ~4x speedup vs the current atomics-based
implementation.
- A new driver "ocxl" for "Open Coherent Accelerator Processor
Interface (OpenCAPI)" devices.
- Support for new device tree properties on PowerVM to describe
hotpluggable memory and devices.
- Add support for CLOCK_{REALTIME/MONOTONIC}_COARSE to the 64-bit
VDSO.
- Freescale updates from Scott: fixes for CPM GPIO and an FSL PCI
erratum workaround, plus a minor cleanup patch.
As well as quite a lot of other changes all over the place, and small
fixes and cleanups as always.
Thanks to: Alan Modra, Alastair D'Silva, Alexey Kardashevskiy,
Alistair Popple, Andreas Schwab, Andrew Donnellan, Aneesh Kumar K.V,
Anju T Sudhakar, Anshuman Khandual, Anton Blanchard, Arnd Bergmann,
Balbir Singh, Benjamin Herrenschmidt, Bhaktipriya Shridhar, Bryant G.
Ly, Cédric Le Goater, Christophe Leroy, Christophe Lombard, Cyril Bur,
David Gibson, Desnes A. Nunes do Rosario, Dmitry Torokhov, Frederic
Barrat, Geert Uytterhoeven, Guilherme G. Piccoli, Gustavo A. R. Silva,
Gustavo Romero, Ivan Mikhaylov, Joakim Tjernlund, Joe Perches, Josh
Poimboeuf, Juan J. Alvarez, Julia Cartwright, Kamalesh Babulal,
Madhavan Srinivasan, Mahesh Salgaonkar, Mathieu Malaterre, Michael
Bringmann, Michael Hanselmann, Michael Neuling, Nathan Fontenot,
Naveen N. Rao, Nicholas Piggin, Paul Mackerras, Philippe Bergheaud,
Ram Pai, Russell Currey, Santosh Sivaraj, Scott Wood, Seth Forshee,
Simon Guo, Stewart Smith, Sukadev Bhattiprolu, Thiago Jung Bauermann,
Vaibhav Jain, Vasyl Gomonovych"
* tag 'powerpc-4.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (199 commits)
powerpc/mm/radix: Fix build error when RADIX_MMU=n
macintosh/ams-input: Use true and false for boolean values
macintosh: change some data types from int to bool
powerpc/watchdog: Print the NIP in soft_nmi_interrupt()
powerpc/watchdog: regs can't be null in soft_nmi_interrupt()
powerpc/watchdog: Tweak watchdog printks
powerpc/cell: Remove axonram driver
rtc-opal: Fix handling of firmware error codes, prevent busy loops
powerpc/mpc52xx_gpt: make use of raw_spinlock variants
macintosh/adb: Properly mark continued kernel messages
powerpc/pseries: Fix cpu hotplug crash with memoryless nodes
powerpc/numa: Ensure nodes initialized for hotplug
powerpc/numa: Use ibm,max-associativity-domains to discover possible nodes
powerpc/kernel: Block interrupts when updating TIDR
powerpc/powernv/idoa: Remove unnecessary pcidev from pci_dn
powerpc/mm/nohash: do not flush the entire mm when range is a single page
powerpc/pseries: Add Initialization of VF Bars
powerpc/pseries/pci: Associate PEs to VFs in configure SR-IOV
powerpc/eeh: Add EEH notify resume sysfs
powerpc/eeh: Add EEH operations to notify resume
...
* pci/spdx:
PCI: Add SPDX GPL-2.0+ to replace implicit GPL v2 or later statement
PCI: Add SPDX GPL-2.0+ to replace GPL v2 or later boilerplate
PCI: Add SPDX GPL-2.0 to replace COPYING boilerplate
PCI: Add SPDX GPL-2.0 to replace GPL v2 boilerplate
PCI: Add SPDX GPL-2.0 when no license was specified
* pci/misc:
PCI: Add dummy pci_irqd_intx_xlate() for CONFIG_PCI=n build
PCI: Add wrappers for dev_printk()
PCI: Remove unnecessary messages for memory allocation failures
PCI: Add #defines for Completion Timeout Disable feature
hinic: Replace PCI pool old API
net: e100: Replace PCI pool old API
block: DAC960: Replace PCI pool old API
MAINTAINERS: Include more PCI files
PCI: Remove unneeded kallsyms include
powerpc/pci: Unroll two pass loop when scanning bridges
powerpc/pci: Use for_each_pci_bridge() helper
* pci/dpc:
PCI/DPC: Reformat DPC register definitions
PCI/DPC: Add and use DPC Status register field definitions
PCI/DPC: Squash dpc_rp_pio_get_info() into dpc_process_rp_pio_error()
PCI/DPC: Remove unnecessary RP PIO register structs
PCI/DPC: Push dpc->rp_pio_status assignment into dpc_rp_pio_get_info()
PCI/DPC: Squash dpc_rp_pio_print_error() into dpc_rp_pio_get_info()
PCI/DPC: Make RP PIO log size check more generic
PCI/DPC: Rename local "status" to "dpc_status"
PCI/DPC: Squash dpc_rp_pio_print_tlp_header() into dpc_rp_pio_print_error()
PCI/DPC: Process RP PIO details only if RP PIO extensions supported
PCI/DPC: Read RP PIO Log Size once at probe
PCI/DPC: Rename struct dpc_dev.rp to rp_extensions
PCI/DPC: Add local variable for DPC capability offset
PCI/DPC: Rename interrupt_event_handler() to dpc_work()
PCI/DPC: Fix interrupt message number print
PCI/DPC: Enable DPC only if AER is available
PCI/DPC: Fix shared interrupt handling
Add definitions for DPC Status register fields and use them in the code.
No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sinan Kaya <okaya@codeaurora.org>
dpc_process_rp_pio_error() only calls dpc_rp_pio_get_info(), so squash them
together. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sinan Kaya <okaya@codeaurora.org>
We read and immediately print the RP PIO log registers. We don't save
them, so there's no need to define structs for them. Remove the structs
and read the registers into local variables instead. No functional change
intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sinan Kaya <okaya@codeaurora.org>
Move the dpc->rp_pio_status assignment into dpc_rp_pio_get_info() since
that's where we read rp_pio->status anway. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sinan Kaya <okaya@codeaurora.org>
Separating dpc_rp_pio_print_error() doesn't really provide any useful
abstraction, so squash it into its caller, dpc_rp_pio_get_info(). No
functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sinan Kaya <okaya@codeaurora.org>
In dpc_probe(), we set dpc->rp_log_size to zero if we think the hardware
reports an invalid size. In this case, we could have dpc->rp_extensions
set but dpc->rp_log_size == 0, and we should print the basic RP PIO
registers but not the variable-size portion. We already checked for
dpc->rp_log_size < 4 above, so this patch is just for consistency of style.
No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sinan Kaya <okaya@codeaurora.org>
In dpc_rp_pio_get_info() rename the local "status" variable to
"dpc_status". This is to make room for another variable named "status" in
a subsequent patch. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sinan Kaya <okaya@codeaurora.org>
Separating dpc_rp_pio_print_tlp_header() doesn't really provide any useful
abstraction, so squash it into its caller, dpc_rp_pio_print_error(). No
functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sinan Kaya <okaya@codeaurora.org>
The RP PIO registers (status, mask, severity, etc) are only implemented if
the "RP Extensions for DPC" bit is set in the DPC Capabilities register.
Previously we called dpc_process_rp_pio_error(), which reads and decodes
those RP PIO registers, whenever the DPC Status register indicated an "RP
PIO error" (Trigger Reason == 3 and Trigger Reason Extension == 0).
It does seem reasonable to assume that DPC Status would only indicate an RP
PIO error if the RP extensions are supported, but PCIe r4.0, sec 7.9.15.4,
is actually not explicit about that: it does not say "Trigger Reason
Extension == 0 is valid only for Root Ports that support RP Extensions for
DPC."
Check whether the RP Extensions for DPC are supported before trying to read
the RP PIO registers.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sinan Kaya <okaya@codeaurora.org>
The RP PIO Log Size is a read-only field in the DPC Capability, so it is
constant and known at probe-time, but previously we read it every time we
processed an RP PIO error.
Read it once in dpc_probe() (if the RP Extensions for DPC are supported)
and remember the size in struct dpc_dev. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sinan Kaya <okaya@codeaurora.org>
"rp" is ambiguous: it might mean "this DPC device is a Root Port." But in
fact, it means "this DPC device is a Root Port *and* it supports a set of
DPC Extensions."
Rename "rp" to "rp_extensions" to make this more clear. No functional
change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sinan Kaya <okaya@codeaurora.org>
Add a local variable for DPC capability offset and replace repeated use of
"dpc->cap_pos" with simply "cap". No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sinan Kaya <okaya@codeaurora.org>
Add SPDX GPL-2.0 to all PCI files that referred to the kernel default
"COPYING" file, which specifies GPL version 2.
Remove the boilerplate language referring to the GPL and "COPYING", relying
on the assertion in b24413180f ("License cleanup: add SPDX GPL-2.0
license identifier to files with no license") that the SPDX identifier may
be used instead of the full boilerplate text.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX GPL-2.0 to all PCI files that specified the GPL version 2 license.
Remove the boilerplate GPL version 2 language, relying on the assertion in
b24413180f ("License cleanup: add SPDX GPL-2.0 license identifier to
files with no license") that the SPDX identifier may be used instead of the
full boilerplate text.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Devices can go offline when erors reported. This patch adds a change
to the kernel object and lets udev know of error. When device resumes,
a change is also set reporting device as online. Therefore, EEH and
AER events are better propagated to user space for PCI devices in all
arches.
Signed-off-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Signed-off-by: Juan J. Alvarez <jjalvare@linux.vnet.ibm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Rename interrupt_event_handler() to dpc_work() so there's more useful
information in stack traces and similar situations. No functional change
intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sinan Kaya <okaya@codeaurora.org>
The interrupt message number is the first 5 bits, but the driver was
masking only the first 4 bits. Fix that by using the existing
define.
Signed-off-by: Keith Busch <keith.busch@intel.com>
[bhelgaas: remove reformatting (done by another patch)]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The "Determination of DPC Control" implementation note in PCIe r4.0, sec
6.1.10, recommends the operating system always link DPC control to the
control of AER, as the two functionalities are strongly connected.
To avoid conflicts over whether platform firmware or the OS controls DPC,
enable DPC only if AER is enabled in the OS, and the device's error
handling does not have firmware-first AER handling.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
b24413180f ("License cleanup: add SPDX GPL-2.0 license identifier to
files with no license") added SPDX GPL-2.0 to several PCI files that
previously contained no license information.
Add SPDX GPL-2.0 to all other PCI files that did not contain any license
information and hence were under the default GPL version 2 license of the
kernel.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add PCI-specific dev_printk() wrappers and use them to simplify the code
slightly. No functional change intended.
Signed-off-by: Frederick Lawler <fred@fredlawl.com>
[bhelgaas: squash into one patch]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
get_device_error_info() reads error information from registers in the AER
capability. If we call it for a device that has no AER capability, it
should return an error, but previously it returned success.
Return 0 (error) if the device doesn't have an AER capability.
Signed-off-by: Keith Busch <keith.busch@intel.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
DPC supports shared interrupts, but it plays very loosely with testing
whether the interrupt is generated by DPC before generating spurious log
messages, such as:
dpc 0000:10:01.2:pcie010: DPC containment event, status:0x1f00 source:0x0000
Testing the status register for zero or -1 is not sufficient when the
device supports the RP PIO First Error Pointer register. Change this to
test whether the interrupt is enabled in the control register, retaining
the device present test, and that the status reports the interrupt as
signaled and DPC is triggered, clearing as a spurious interrupt otherwise.
Additionally, since the interrupt is actually serviced by a workqueue,
disable the interrupt in the control register until that completes or else
we may never see it execute due to further incoming interrupts. A software
generated DPC floods the system otherwise.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Make the PCIe port driver set DPM_FLAG_SMART_SUSPEND and
DPM_FLAG_LEAVE_SUSPENDED for the devices handled by it to benefit
from the opportunistic optimizations in the PCI layer enabled by
these flags.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Per PCIe r3.1, sec 5.5.1, LTR_L1.2_THRESHOLD determines whether we enter
the L1.2 Link state: if L1.2 is enabled and downstream devices have
reported that they can tolerate latency of at least LTR_L1.2_THRESHOLD, we
must enter L1.2 when CLKREQ# is de-asserted.
The implication is that LTR_L1.2_THRESHOLD is the time required to
transition the Link from L0 to L1.2 and back to L0, and per sec 5.5.3.3.1,
Figures 5-16 and 5-17, it appears that the absolute minimum time for those
transitions would be T(POWER_OFF) + T(L1.2) + T(POWER_ON) + T(COMMONMODE).
Therefore, compute LTR_L1.2_THRESHOLD as:
2us T(POWER_OFF)
+ 4us T(L1.2)
+ T(POWER_ON)
+ T(COMMONMODE)
= LTR_L1.2_THRESHOLD
Previously we set LTR_L1.2_THRESHOLD to a fixed value of 163840ns
(163.84us):
#define LTR_L1_2_THRESHOLD_BITS ((1 << 21) | (1 << 23) | (1 << 30))
((1 << 21) | (1 << 23) | (1 << 30)) = 0x40a00000
LTR_L1.2_THRESHOLD_Value = (0x40a00000 & 0x03ff0000) >> 16 = 0xa0 = 160
LTR_L1.2_THRESHOLD_Scale = (0x40a00000 & 0xe0000000) >> 29 = 0x2 (* 1024ns)
LTR_L1.2_THRESHOLD = 160 * 1024ns = 163840ns
Obviously this doesn't account for the circuit characteristics of different
implementations.
Note that while firmware may enable LTR, Linux itself currently does not
enable LTR. When L1.2 is enabled but LTR is not, LTR_L1.2_THRESHOLD is
ignored and we always enter L1.2 when it is enabled and CLKREQ# is
de-asserted. So this patch should not have any effect unless firmware
enables LTR.
Fixes: f1f0366dd6 ("PCI/ASPM: Calculate and save the L1.2 timing parameters")
Link: https://www.coreboot.org/pipermail/coreboot-gerrit/2015-March/021134.html
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Vidya Sagar <vidyas@nvidia.com>
Cc: Kenji Chen <kenji.chen@intel.com>
Cc: Patrick Georgi <pgeorgi@google.com>
Cc: Rajat Jain <rajatja@google.com>
PCIe correctable errors are corrected by hardware. Software may log them,
but no other software intervention is required.
There are two paths to enter the AER recovery code: (1) the native path
where Linux fields the AER interrupt and reads the AER registers directly,
and (2) the ACPI path where firmware reads the AER registers and hands them
off to Linux via the ACPI APEI path.
The AER do_recovery() function calls driver error reporting callbacks
(error_detected(), mmio_enabled(), resume(), etc), attempts recovery (for
fatal errors), and logs a "AER: Device recovery successful" message.
Since there's nothing to recover for correctable errors, the native path
already skips do_recovery(), so it doesn't call the driver callbacks and or
emit the message. Make the APEI path do the same.
Signed-off-by: Tyler Baicar <tbaicar@codeaurora.org>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Summary of modules changes for the 4.15 merge window:
- Treewide module_param_call() cleanup, fix up set/get function
prototype mismatches, from Kees Cook
- Minor code cleanups
Signed-off-by: Jessica Yu <jeyu@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQIcBAABCgAGBQJaDCyzAAoJEMBFfjjOO8FyaYQP/AwHBy6XmwwVlWDP4BqIF6hL
Vhy3ccVLYEORvePv68tWSRPUz5n6+1Ebqanmwtkw6i8l+KwxY2SfkZql09cARc33
2iBE4bHF98iWQmnJbF6me80fedY9n5bZJNMQKEF9VozJWwTMOTQFTCfmyJRDBmk9
iidQj6M3idbSUOYIJjvc40VGx5NyQWSr+FFfqsz1rU5iLGRGEvA3I2/CDT0oTuV6
D4MmFxzE2Tv/vIMa2GzKJ1LGScuUfSjf93Lq9Kk0cG36qWao8l930CaXyVdE9WJv
bkUzpf3QYv/rDX6QbAGA0cada13zd+dfBr8YhchclEAfJ+GDLjMEDu04NEmI6KUT
5lP0Xw0xYNZQI7bkdxDMhsj5jaz/HJpXCjPCtZBnSEKiL4OPXVMe+pBHoCJ2/yFN
6M716XpWYgUviUOdiE+chczB5p3z4FA6u2ykaM4Tlk0btZuHGxjcSWwvcIdlPmjm
kY4AfDV6K0bfEBVguWPJicvrkx44atqT5nWbbPhDwTSavtsuRJLb3GCsHedx7K8h
ZO47lCQFAWCtrycK1HYw+oupNC3hYWQ0SR42XRdGhL1bq26C+1sei1QhfqSgA9PQ
7CwWH4UTOL9fhtrzSqZngYOh9sjQNFNefqQHcecNzcEjK2vjrgQZvRNWZKHSwaFs
fbGX8juZWP4ypbK+irTB
=c8vb
-----END PGP SIGNATURE-----
Merge tag 'modules-for-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/jeyu/linux
Pull module updates from Jessica Yu:
"Summary of modules changes for the 4.15 merge window:
- treewide module_param_call() cleanup, fix up set/get function
prototype mismatches, from Kees Cook
- minor code cleanups"
* tag 'modules-for-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/jeyu/linux:
module: Do not paper over type mismatches in module_param_call()
treewide: Fix function prototypes for module_param_call()
module: Prepare to convert all module_param_call() prototypes
kernel/module: Delete an error message for a failed memory allocation in add_module_usage()
* pci/msi:
PCI/portdrv: Compute MSI/MSI-X IRQ vectors after final allocation
PCI/portdrv: Factor out Interrupt Message Number lookup
PCI/portdrv: Consolidate comments
PCI/portdrv: Add #defines for AER and DPC Interrupt Message Number masks
* pci/misc:
PCI: Fix kernel-doc build warning
PCI: Move PCI_QUIRKS to the PCI bus menu
alpha/PCI: Make pdev_save_srm_config() static
PCI: Remove unused declarations
PCI: Remove redundant pci_dev, pci_bus, resource declarations
PCI: Remove redundant pcibios_set_master() declarations
PCI/PME: Handle invalid data when reading Root Status
x86/pci/intel_mid_pci: Constify intel_mid_pci_ops and make it __initconst
PCI: Constify pci_dev_type structure
* pci/aspm:
PCI/ASPM: Add L1 Substates definitions
PCI/ASPM: Reformat ASPM register definitions
PCI/ASPM: Use correct capability pointer to program LTR_L1.2_THRESHOLD
PCI/ASPM: Account for downstream device's Port Common_Mode_Restore_Time
PCI/ASPM: Deal with missing root ports in link state handling
Add and use #defines for L1 Substate register fields instead of hard-coding
the masks. Also update comments to use names from the spec. No functional
change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Vidya Sagar <vidyas@nvidia.com>
Previously we programmed the LTR_L1.2_THRESHOLD in the parent (upstream)
device using the capability pointer of the *child* (downstream) device,
which corrupted some random word of the parent's config space.
Use the parent's L1 SS capability pointer to program its
LTR_L1.2_THRESHOLD.
Fixes: aeda9adeba ("PCI/ASPM: Configure L1 substate settings")
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Vidya Sagar <vidyas@nvidia.com>
CC: stable@vger.kernel.org # v4.11+
CC: Rajat Jain <rajatja@google.com>
Every Port that supports the L1.2 substate advertises its Port
Common_Mode_Restore_Time, i.e., the time the Port requires to re-establish
common mode when exiting L1.2 (see PCIe r3.1, sec 7.33.2).
Per sec 5.5.3.3.1, when exiting L1.2, the Downstream Port (the device at
the upstream end of the link) must send TS1 training sequences for at least
T(COMMONMODE) after it detects electrical idle exit on the Link. We want
this to be long enough for both ends of the Link, so we should set it to
the maximum of the Port Common_Mode_Restore_Time for the upstream and
downstream components on the Link.
Previously we only looked at the Port Common_Mode_Restore_Time of the
upstream device, so if the downstream device required more time, we didn't
program the upstream device's T(COMMONMODE) correctly.
Fixes: f1f0366dd6 ("PCI/ASPM: Calculate and save the L1.2 timing parameters")
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Vidya Sagar <vidyas@nvidia.com>
Acked-by: Rajat Jain <rajatja@google.com>
CC: stable@vger.kernel.org # v4.11+
PCIe PME and native hotplug share the same interrupt number, so hotplug
interrupts are also processed by PME. In some cases, e.g., a Link Down
interrupt, a device may be present but unreachable, so when we try to
read its Root Status register, the read fails and we get all ones data
(0xffffffff).
Previously, we interpreted that data as PCI_EXP_RTSTA_PME being set, i.e.,
"some device has asserted PME," so we scheduled pcie_pme_work_fn(). This
caused an infinite loop because pcie_pme_work_fn() tried to handle PME
requests until PCI_EXP_RTSTA_PME is cleared, but with the link down,
PCI_EXP_RTSTA_PME can't be cleared.
Check for the invalid 0xffffffff data everywhere we read the Root Status
register.
1469d17dd3 ("PCI: pciehp: Handle invalid data when reading from
non-existent devices") added similar checks in the hotplug driver.
Signed-off-by: Qiang Zheng <zhengqiang10@huawei.com>
[bhelgaas: changelog, also check in pcie_pme_work_fn(), use "~0" to follow
other similar checks]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Some of the PCIe services such as AER are being left enabled during
shutdown. This might cause spurious AER errors while SOC is being powered
down.
Clean up the PCIe services gracefully during shutdown to clear these false
positives.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Several function prototypes for the set/get functions defined by
module_param_call() have a slightly wrong argument types. This fixes
those in an effort to clean up the calls when running under type-enforced
compiler instrumentation for CFI. This is the result of running the
following semantic patch:
@match_module_param_call_function@
declarer name module_param_call;
identifier _name, _set_func, _get_func;
expression _arg, _mode;
@@
module_param_call(_name, _set_func, _get_func, _arg, _mode);
@fix_set_prototype
depends on match_module_param_call_function@
identifier match_module_param_call_function._set_func;
identifier _val, _param;
type _val_type, _param_type;
@@
int _set_func(
-_val_type _val
+const char * _val
,
-_param_type _param
+const struct kernel_param * _param
) { ... }
@fix_get_prototype
depends on match_module_param_call_function@
identifier match_module_param_call_function._get_func;
identifier _val, _param;
type _val_type, _param_type;
@@
int _get_func(
-_val_type _val
+char * _val
,
-_param_type _param
+const struct kernel_param * _param
) { ... }
Two additional by-hand changes are included for places where the above
Coccinelle script didn't notice them:
drivers/platform/x86/thinkpad_acpi.c
fs/lockd/svc.c
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Jessica Yu <jeyu@kernel.org>
When setting up portdrv MSI/MSI-X interrupts, we previously allocated the
maximum possible number of vectors, read the Interrupt Message Numbers for
each service, saved the IRQ for each, freed the vectors, and finally used
the largest Message Number to reallocate only as many vectors as we need.
The problem is that freeing the vectors invalidates their IRQs, so the
saved IRQ numbers may now be invalid, which can result in errors like
this:
pcie_pme: probe of 0000:00:00.0:pcie001 failed with error -22
pciehp 0000:00:00.0:pcie004: Cannot get irq 20 for the hotplug controller
aer: probe of 0000:00:00.0:pcie002 failed with error -22
dpc 0000:00:00.0:pcie010: request IRQ22 failed: -22
Change the setup so we save the Interrupt Message Numbers (not the IRQs)
before we free the original setup, then use the Message Numbers to compute
the IRQs (via pci_irq_vector()) *after* we reallocate the vectors.
This should always be safe for MSI-X because the Message Numbers are fixed.
For MSI, the hardware is allowed to change Message Numbers when we update
the MSI Multiple Message Enable field when reallocating the vectors, but
since we allocate enough vectors to accommodate the largest Message Number
we found, that's unlikely. See PCIe r3.1, sec 7.8.2, 7.10.10, 7.31.2.
Fixes: 3674cc49da ("PCI/portdrv: Use pci_irq_alloc_vectors()")
Based-on-patch-by: Dongdong Liu <liudongdong3@huawei.com>
Tested-by: Dongdong Liu <liudongdong3@huawei.com> # HiSilicon hip08
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Factor out Interrupt Message Number lookup from the MSI/MSI-X interrupt
setup. One side effect is that we only have to check once to see if we
have enough vectors for all the services. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Consolidate some repetitive comments so we can see the code better. No
functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
In the AER case, the mask isn't strictly necessary because there are no
higher-order bits above the Interrupt Message Number, but using a #define
will make it possible to grep for it.
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Dongdong Liu <liudongdong3@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Even though it is unconventional, some PCIe host implementations omit the
root ports entirely, and simply consist of a host bridge (which is not
modeled as a device in the PCI hierarchy) and a link.
When the downstream device is an endpoint, our current code does not seem
to mind this unusual configuration. However, when PCIe switches are
involved, the ASPM code assumes that any downstream switch port has a
parent, and blindly dereferences the bus->parent->self field of the pci_dev
struct to chain the downstream link state to the link state of the root
port. Given that the root port is missing, the link is not modeled at all,
and nor is the link state, and attempting to access it results in a NULL
pointer dereference and a crash.
Avoid this by allowing the link state chain to terminate at the downstream
port if no root port exists.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Previously, if an non-fatal error was reported by an endpoint, we
called report_error_detected() for the endpoint, every sibling on the
bus, and their descendents. If any of them did not implement the
.error_detected() method, do_recovery() failed, leaving all these
devices unrecovered.
For example, the system described in the bugzilla below has two devices:
0000:74:02.0 [19e5:a230] SAS controller, driver has .error_detected()
0000:74:03.0 [19e5:a235] SATA controller, driver lacks .error_detected()
When a device such as 74:02.0 reported a non-fatal error, do_recovery()
failed because 74:03.0 lacked an .error_detected() method. But per PCIe
r3.1, sec 6.2.2.2.2, such an error does not compromise the Link and
does not affect 74:03.0:
Non-fatal errors are uncorrectable errors which cause a particular
transaction to be unreliable but the Link is otherwise fully functional.
Isolating Non-fatal from Fatal errors provides Requester/Receiver logic
in a device or system management software the opportunity to recover from
the error without resetting the components on the Link and disturbing
other transactions in progress. Devices not associated with the
transaction in error are not impacted by the error.
Report non-fatal errors only to the endpoint that reported them. We really
want to check for AER_NONFATAL here, but the current code structure doesn't
allow that. Looking for pci_channel_io_normal is the best we can do now.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=197055
Fixes: 6c2b374d74 ("PCI-Express AER implemetation: AER core and aerdriver")
Signed-off-by: Gabriele Paoloni <gabriele.paoloni@huawei.com>
Signed-off-by: Dongdong Liu <liudongdong3@huawei.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
... and __initconst if applicable.
Based on similar work for an older kernel in the Grsecurity patch.
[JD: fix toshiba-wmi build]
[JD: add htcpen]
[JD: move __initconst where checkscript wants it]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Use a local "struct device *dev" for brevity and consistency in DPC driver.
No functional change intended.
Signed-off-by: Dongdong Liu <liudongdong3@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Add eDPC support. Get and print the RP PIO error information when the
trigger condition is RP PIO error.
For more information on eDPC, please see PCI Express Base Specification
Revision 3.1, section 6.2.10.3, or view the PCI-SIG eDPC ECN here:
https://pcisig.com/sites/default/files/specification_documents/ECN_Enhanced_DPC_2012-11-19_final.pdf
Signed-off-by: Dongdong Liu <liudongdong3@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Move the error handler methods to struct pcie_port_service_driver and avoid
the detour through the mostly unused pci_error_handlers structure.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Commit 76cde7e495 (PCI / PM: Make PCIe PME interrupts wake up from
suspend-to-idle) went too far with preventing pcie_pme_work_fn() from
clearing the root port's PME Status and re-enabling the PME interrupt
which should be done for PMEs to work correctly after system resume.
The failing scenario is as follows:
1. pcie_pme_suspend() finds that the PME IRQ should be designated
for system wakeup, so it calls enable_irq_wake() and then sets
data->suspend_level to PME_SUSPEND_WAKEUP.
2. PME interrupt happens at this point.
3. pcie_pme_irq() runs, disables the PME interrupt and queues up
the execution of pcie_pme_work_fn().
4. pcie_pme_work_fn() runs before pcie_pme_resume() and breaks out
of the loop right away, because data->suspend_level is not
PME_SUSPEND_NONE, and it doesn't re-enable the PME interrupt
for the same reason.
5. pcie_pme_resume() runs and simply calls disable_irq_wake()
without re-enabling the PME interrupt (because data->suspend_level
is not PME_SUSPEND_NONE), so the PME interrupt remains disabled
and the PME Status remains set.
To fix this notice that there is no reason why pcie_pme_work_fn()
should behave in a special way during system resume if the PME
interrupt is not disabled by pcie_pme_suspend() and partially revert
commit 76cde7e495 and restore the previous (and correct) behavior
of pcie_pme_work_fn().
Fixes: 76cde7e495 (PCI / PM: Make PCIe PME interrupts wake up from suspend-to-idle)
Reported-and-tested-by: Naresh Solanki <naresh.solanki@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
* pci/portdrv:
PCI/portdrv: Allocate MSI/MSI-X vector for Downstream Port Containment
PCI/portdrv: Support multiple interrupts for MSI as well as MSI-X
The run_wake flag in struct dev_pm_info is used to indicate whether
or not the device is capable of generating remote wakeup signals at
run time (or in the system working state), but the distinction
between runtime remote wakeup and system wakeup signaling has always
been rather artificial. The only practical reason for it to exist
at the core level was that ACPI and PCI treated those two cases
differently, but that's not the case any more after recent changes.
For this reason, get rid of the run_wake flag and, when applicable,
use device_set_wakeup_capable() and device_can_wakeup() instead of
device_set_run_wake() and device_run_wake(), respectively.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
The pme_interrupt flag in struct pci_dev is set when PMEs generated
by the device are going to be signaled via root port PME interrupts.
Ironically enough, that information is only used by the code setting
up device wakeup through ACPI which returns as soon as it sees the
pme_interrupt flag set while setting up "remote runtime wakeup".
That is questionable, however, because in theory there may be PCIe
devices using out-of-band PME signaling under root ports handled
by the native PME code or devices requiring wakeup power setup to be
carried out by AML. For such devices, ACPI wakeup should be invoked
regardless of whether or not native PME signaling is used in general.
For this reason, drop the pme_interrupt flag and rework the code
using it which then allows the ACPI-based device wakeup handling
in PCI to be consolidated to use one code path for both "runtime
remote wakeup" and system wakeup (from sleep states).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Currently pcie_port_enable_irq_vec() only allocates MSI/MSI-X vectors for
PME, hotplug, and AER.
The Downstream Port Containment feature also supports MSI/MSI-X interrupts,
so allocate a vector for it, too.
Signed-off-by: Liudongdong <liudongdong3@huawei.com>
Signed-off-by: Gabriele Paoloni <gabriele.paoloni@huawei.com>
[bhelgaas: changelog, comment]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Root Ports can generate several different interrupts using either MSI or
MSI-X, but we only support that for MSI-X. Ports that support MSI but not
MSI-X are currently limited to sharing a single interrupt.
Rename pcie_port_enable_msix() to pcie_port_enable_irq_vec() and extend it
to support multiple interrupts using either MSI-X (preferred) or MSI.
Signed-off-by: Gabriele Paoloni <gabriele.paoloni@huawei.com>
[bhelgaas: changelog, reword comments, simplify PME/hotplug no-MSI logic]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
This driver was OR'ing desired bits from the existing control setting.
That could create an invalid DPC Trigger Enabled configuration if the
platform previously set this to "ERR_FATAL", 01b. The driver currently
wants to set this to ERR_NONFATAL/ERR_FATAL, 10b, and the logical OR of
this gets 11b, which is reserved. Fix that by masking off the fields it is
setting.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The DPC interupt may be executed on a device that is being removed. Skip
queuing event handling if the status is all 1's, which should be seen only
if the device is not present.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add a new state to pci_dev to be set when it is unexpectedly disconnected.
The PCI driver tear down functions can observe this new device state so
they may skip operations that will fail.
The pciehp and pcie-dpc drivers are aware when the link is down, so these
set the flag when their handlers detect the device is disconnected.
Tested-by: Krishna Dhulipala <krishnad@fb.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Wei Zhang <wzhang@fb.com>
We call pcie_aspm_exit_link_state() when we remove a device. If the device
is the last PCIe function to be removed below a bridge and the bridge has
an ASPM link_state struct, we disable ASPM on the link. Disabling ASPM
requires link->downstream (used in pcie_config_aspm_link()).
We previously set link->downstream in pcie_aspm_cap_init(), but only if the
device was not blacklisted. Removing the blacklisted device caused a NULL
pointer dereference in the pcie_aspm_exit_link_state() ->
pcie_config_aspm_link() path:
# echo 1 > /sys/bus/pci/devices/0000\:0b\:00.0/remove
...
BUG: unable to handle kernel NULL pointer dereference at 0000000000000080
IP: pcie_config_aspm_link+0x5d/0x2b0
Call Trace:
pcie_aspm_exit_link_state+0x75/0x130
pci_stop_bus_device+0xa4/0xb0
pci_stop_and_remove_bus_device_locked+0x1a/0x30
remove_store+0x50/0x70
dev_attr_store+0x18/0x30
sysfs_kf_write+0x44/0x60
kernfs_fop_write+0x10e/0x190
__vfs_write+0x28/0x110
? rcu_read_lock_sched_held+0x5d/0x80
? rcu_sync_lockdep_assert+0x2c/0x60
? __sb_start_write+0x173/0x1a0
? vfs_write+0xb3/0x180
vfs_write+0xc4/0x180
SyS_write+0x49/0xa0
do_syscall_64+0xa6/0x1c0
entry_SYSCALL64_slow_path+0x25/0x25
---[ end trace bd187ee0267df5d9 ]---
To avoid this, set link->downstream in alloc_pcie_link_state(), so every
pcie_link_state structure has a valid link->downstream pointer.
[bhelgaas: changelog]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rajat Jain <rajatja@google.com>
CC: stable@vger.kernel.org
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=4Owc
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.11-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- add ASPM L1 substate support
- enable PCIe Extended Tags when supported
- configure PCIe MPS settings on iProc, Versatile, X-Gene, and Xilinx
- increase VPD access timeout
- add ACS quirks for Intel Union Point, Qualcomm QDF2400 and QDF2432
- use new pci_irq_alloc_vectors() in more drivers
- fix MSI affinity memory leak
- remove unused MSI interfaces and update documentation
- remove unused AER .link_reset() callback
- avoid pci_lock / p->pi_lock deadlock seen with perf
- serialize sysfs enable/disable num_vfs operations
- move DesignWare IP from drivers/pci/host/ to drivers/pci/dwc/ and
refactor so we can support both hosts and endpoints
- add DT ECAM-like support for HiSilicon Hip06/Hip07 controllers
- add Rockchip system power management support
- add Thunder-X cn81xx and cn83xx support
- add Exynos 5440 PCIe PHY support
* tag 'pci-v4.11-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (93 commits)
PCI: dwc: Remove dependency of designware on CONFIG_PCI
PCI: dwc: Add CONFIG_PCIE_DW_HOST to enable PCI dwc host
PCI: dwc: Split pcie-designware.c into host and core files
PCI: dwc: designware: Fix style errors in pcie-designware.c
PCI: dwc: designware: Parse "num-lanes" property in dw_pcie_setup_rc()
PCI: dwc: all: Split struct pcie_port into host-only and core structures
PCI: dwc: designware: Get device pointer at the start of dw_pcie_host_init()
PCI: dwc: all: Rename cfg_read/cfg_write to read/write
PCI: dwc: all: Use platform_set_drvdata() to save private data
PCI: dwc: designware: Move register defines to designware header file
PCI: dwc: Use PTR_ERR_OR_ZERO to simplify code
PCI: dra7xx: Group PHY API invocations
PCI: dra7xx: Enable MSI and legacy interrupts simultaneously
PCI: dra7xx: Add support to force RC to work in GEN1 mode
PCI: dra7xx: Simplify probe code with devm_gpiod_get_optional()
PCI: Move DesignWare IP support to new drivers/pci/dwc/ directory
PCI: exynos: Support the PHY generic framework
Documentation: binding: Modify the exynos5440 PCIe binding
phy: phy-exynos-pcie: Add support for Exynos PCIe PHY
Documentation: samsung-phy: Add exynos-pcie-phy binding
...
* pci/msi:
PCI/MSI: Update MSI/MSI-X bits in PCIEBUS-HOWTO
PCI/MSI: Document pci_alloc_irq_vectors(), deprecate pci_enable_msi()
PCI/MSI: Return -ENOSPC if pci_enable_msi_range() can't get enough vectors
PCI/portdrv: Use pci_irq_alloc_vectors()
PCI/MSI: Check that we have a legacy interrupt line before using it
PCI/MSI: Remove pci_msi_domain_{alloc,free}_irqs()
PCI/MSI: Remove unused pci_msi_create_default_irq_domain()
PCI/MSI: Return failure when msix_setup_entries() fails
PCI/MSI: Remove pci_enable_msi_{exact,range}()
amd-xgbe: Update PCI support to use new IRQ functions
[media] cobalt: use pci_irq_allocate_vectors()
PCI/MSI: Fix msi_capability_init() kernel-doc warnings
Since the exit latencies for L1 substates are not advertised by a device,
it is not clear in spec how to do a L1 substate exit latency check. We
assume that the L1 exit latencies advertised by a device include L1
substate latencies (and hence do not do any check). If that is not true,
we should do some sort of check here.
(I'm not clear about what that check should like currently. I'd be glad to
take up any suggestions).
Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Configure the L1 substate settings on the upstream and downstream devices,
while taking care of the rules dictated by the PCIe spec.
[bhelgaas: drop "inline"]
Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The PCIe spec (r3.1, sec 7.33) says the L1 PM Substates Capability may be
implemented only in function 0.
Read the L1 substate capability structures of upstream and downstream
components of the link and set it up in the device structure.
[bhelgaas: add specific spec reference]
Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add support for ASPM L1 substates. For details about L1 substates, see the
PCIe r3.1 spec, which includes the ECN below in secs 5.5 and 7.33.
Add macros for the 4 new L1 substates, and add a new ASPM "POWER_SUPERSAVE"
policy that can be used to enable L1 substates on a system if desired. The
new policy is in a sense, a superset of the existing POWERSAVE policy. The
4 policies are now:
DEFAULT: Reads and uses whatever ASPM states BIOS enabled
PERFORMANCE: Everything except L0 disabled.
POWERSAVE: L0s and L1 enabled (but not L1 substates)
POWER_SUPERSAVE: L0s + L1 + L1 substates also enabled
[bhelgaas: add PCIe r3.1 spec reference]
Link: https://pcisig.com/sites/default/files/specification_documents/ECN_L1_PM_Substates_with_CLKREQ_31_May_2013_Rev10a.pdf
Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use pci_irq_alloc_vectors() and greatly simplify the code by managing the
vector number for the subservices directly.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Per PCIe r3.1, sec 6.2.10 and sec 7.13.4, on Root Ports that support "RP
Extensions for DPC",
When the DPC Trigger Status bit is Set and the DPC RP Busy bit is Set,
software must leave the Root Port in DPC until the DPC RP Busy bit reads
0b.
Wait up to 1 second for the Root Port to become non-busy.
[bhelgaas: changelog, spec references]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Decode the currently defined extended event reasons rather than just using
the generic "extended" explanation.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
In a struct pcie_link_state, link->root points to the pcie_link_state of
the root of the PCIe hierarchy. For the topmost link, this points to
itself (link->root = link). For others, we copy the pointer from the
parent (link->root = link->parent->root).
Previously we recognized that Root Ports originated PCIe hierarchies, but
we treated PCI/PCI-X to PCIe Bridges as being in the middle of the
hierarchy, and when we tried to copy the pointer from link->parent->root,
there was no parent, and we dereferenced a NULL pointer:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000090
IP: [<ffffffff9e424350>] pcie_aspm_init_link_state+0x170/0x820
Recognize that PCI/PCI-X to PCIe Bridges originate PCIe hierarchies just
like Root Ports do, so link->root for these devices should also point to
itself.
Fixes: 51ebfc92b7 ("PCI: Enumerate switches below PCI-to-PCIe bridges")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=193411
Link: https://bugzilla.opensuse.org/show_bug.cgi?id=1022181
Tested-by: lists@ssl-mail.com
Tested-by: Jayachandran C. <jnair@caviumnetworks.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v4.2+
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ut0k
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.10-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"PCI changes:
- add support for PCI on ARM64 boxes with ACPI. We already had this
for theoretical spec-compliant hardware; now we're adding quirks
for the actual hardware (Cavium, HiSilicon, Qualcomm, X-Gene)
- add runtime PM support for hotplug ports
- enable runtime suspend for Intel UHCI that uses platform-specific
wakeup signaling
- add yet another host bridge registration interface. We hope this is
extensible enough to subsume the others
- expose device revision in sysfs for DRM
- to avoid device conflicts, make sure any VF BAR updates are done
before enabling the VF
- avoid unnecessary link retrains for ASPM
- allow INTx masking on Mellanox devices that support it
- allow access to non-standard VPD for Chelsio devices
- update Broadcom iProc support for PAXB v2, PAXC v2, inbound DMA,
etc
- update Rockchip support for max-link-speed
- add NVIDIA Tegra210 support
- add Layerscape LS1046a support
- update R-Car compatibility strings
- add Qualcomm MSM8996 support
- remove some uninformative bootup messages"
* tag 'pci-v4.10-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (115 commits)
PCI: Enable access to non-standard VPD for Chelsio devices (cxgb3)
PCI: Expand "VPD access disabled" quirk message
PCI: pciehp: Remove loading message
PCI: hotplug: Remove hotplug core message
PCI: Remove service driver load/unload messages
PCI/AER: Log AER IRQ when claiming Root Port
PCI/AER: Log errors with PCI device, not PCIe service device
PCI/AER: Remove unused version macros
PCI/PME: Log PME IRQ when claiming Root Port
PCI/PME: Drop unused support for PMEs from Root Complex Event Collectors
PCI: Move config space size macros to pci_regs.h
x86/platform/intel-mid: Constify mid_pci_platform_pm
PCI/ASPM: Don't retrain link if ASPM not possible
PCI: iproc: Skip check for legacy IRQ on PAXC buses
PCI: pciehp: Leave power indicator on when enabling already-enabled slot
PCI: pciehp: Prioritize data-link event over presence detect
PCI: rcar: Add gen3 fallback compatibility string for pcie-rcar
PCI: rcar: Use gen2 fallback compatibility last
PCI: rcar-gen2: Use gen2 fallback compatibility last
PCI: rockchip: Move the deassert of pm/aclk/pclk after phy_init()
..
* pci/pm:
x86/platform/intel-mid: Constify mid_pci_platform_pm
PCI: pciehp: Add runtime PM support for PCIe hotplug ports
ACPI / hotplug / PCI: Make device_is_managed_by_native_pciehp() public
ACPI / hotplug / PCI: Use cached copy of PCI_EXP_SLTCAP_HPC bit
PCI: Unfold conditions to block runtime PM on PCIe ports
PCI: Consolidate conditions to allow runtime PM on PCIe ports
PCI: Activate runtime PM on a PCIe port only if it can suspend
PCI: Speed up algorithm in pci_bridge_d3_update()
PCI: Autosense device removal in pci_bridge_d3_update()
PCI: Don't acquire ref on parent in pci_bridge_d3_update()
USB: UHCI: report non-PME wakeup signalling for Intel hardware
PCI: Check for PME in targeted sleep state
Remove the "service driver %s loaded" and unloaded messages. All service
drivers already log something in their probe functions, where they can log
more useful details.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
All other AER-related log messages use the PCI device, e.g.,
"pci 0000:00:1c.0", not the PCIe service device, e.g.,
"aer 0000:00:1c.0:pcie02".
Change the probe error messages to match the rest and include a little
context.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Remove the unused DRIVER_VERSION, DRIVER_AUTHOR, and DRIVER_DESC macros.
The author information is already included in a comment above.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We already log a "Signaling PME" whenever the PME service driver claims a
Root Port. In fact, we also log the same message for every device in the
hierarchy below the Root Port.
Log the "Signaling PME" once (only for the Root Port, since we can
trivially find out which devices are below the Root Port), and include the
IRQ number in the message to help connect the dots with /proc/interrupts.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Since we register pcie_pme_driver only for PCI_EXP_TYPE_ROOT_PORT, the PME
driver never claims Root Complex Event Collectors.
Remove unused code related to Root Complex Event Collectors.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some (defective) PCIe devices are not able to reliably do link retraining.
Check to see if ASPM is possible between link partners before configuring
common clocking, and doing the resulting link retraining. If ASPM is not
possible, there is no reason to risk losing access to a device due to an
unnecessary link retraining.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Export pcie_find_root_port() so we can use it outside of PCIe-AER error
injection.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The conditions to allow runtime PM on PCIe ports are currently spread
across two different files: The condition relating to hotplug ports is
located in portdrv_pci.c whereas all other conditions are located in pci.c.
Consolidate all conditions in a single place in pci.c, thus making it
easier to follow the logic and amend conditions down the road.
Note that the condition relating to hotplug ports is inserted *before* the
condition relating to the "pcie_port_pm=force" command line option, so
runtime PM is not afforded to hotplug ports even if this option is given.
That's exactly how the code behaved up until now. If this is not desired,
the ordering of the conditions can simply be reversed.
No functional change intended.
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently pcie_portdrv_probe() activates runtime PM on a PCIe port even
if it will never actually suspend because the BIOS is too old or the
"pcie_port_pm=off" option was specified on the kernel command line.
A few CPU cycles can be saved by not activating runtime PM at all in these
cases, because rpm_idle() and rpm_suspend() will bail out right at the
beginning when calling rpm_check_suspend_allowed(), instead of carrying out
various locking and assignments, invoking rpm_callback(), getting back
-EBUSY and rolling everything back.
The conditions checked in pci_bridge_d3_possible() are all static, they
never change during uptime of the system, hence it's safe to call this to
determine if runtime PM should be activated.
No functional change intended.
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use DEVICE_ATTR_RW for read-write attributes. This simplifies the source
code, improves readability, and reduces the chance of inconsistencies.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@rw@
declarer name DEVICE_ATTR;
identifier x,x_show,x_store;
@@
DEVICE_ATTR(x, \(0644\|S_IRUGO|S_IWUSR\), x_show, x_store);
@script:ocaml@
x << rw.x;
x_show << rw.x_show;
x_store << rw.x_store;
@@
if not (x^"_show" = x_show && x^"_store" = x_store)
then Coccilib.include_match false
@@
declarer name DEVICE_ATTR_RW;
identifier rw.x,rw.x_show,rw.x_store;
@@
- DEVICE_ATTR(x, \(0644\|S_IRUGO|S_IWUSR\), x_show, x_store);
+ DEVICE_ATTR_RW(x);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
0516c8bcd2 ("PCI: PCIe portdrv: Simplily probe callback of service
drivers") removed the "id" argument of aer_probe() but neglected to remove
the kernel-doc comment. Update the comment.
[bhelgaas: changelog]
Signed-off-by: Cao jin <caoj.fnst@cn.fujitsu.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Save the position of the error reporting capability so it doesn't need to
be rediscovered during error handling.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Lukas Wunner <lukas@wunner.de>
When handling AER events, we previously allocated a struct aer_err_info,
processed the error, and freed the struct. But aer_isr_one_error() is
serialized by rpc_mutex, so we never need more than one copy of the struct,
and the struct is only about 70 bytes, so we're not saving much by
allocating it dynamically.
Embed a struct aer_err_info directly in struct aer_rpc, which is allocated
at probe-time by aer_probe().
[bhelgaas: changelog]
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Currently the AER severity is being translated twice in the code flow for
PCIe errors. It is first translated in ghes_do_proc() before calling into
the AER driver. Then it is translated again when the AER driver calls
cper_print_aer(). This causes the severity that is used in
cper_print_aer() to be incorrect.
Remove the second translation that is in cper_print_aer() since this
function is already receiving the correct AER severity.
Signed-off-by: Tyler Baicar <tbaicar@codeaurora.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Borislav Petkov <bp@suse.de>
Per the PCI Firmware spec, r3.0, sec 4.5.1, on ACPI systems, the OS must
not use AER unless _OSC is present and _OSC grants AER control to the OS.
The aerdriver.forceload kernel parameter was a way to enable Linux AER
support on ACPI systems that lack _OSC or fail to grant control the the OS.
Enabling Linux AER support when the firmware doesn't want us to is a recipe
for problems, e.g., the firmware might be handling AER itself.
Remove the aerdriver.forceload kernel parameter and related supporting
code.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The aerdriver.nosourceid kernel parameter was intended for working around
broken chipsets don't supply the source ID for AER events. We recently
added PCI_BUS_FLAGS_NO_AERSID, which can be set by quirks for the same
purpose.
Remove the aerdriver.nosourceid kernel parameter. For anything other than
debugging, asking users to find and use kernel parameters is a poor user
experience. Instead, we should add PCI_BUS_FLAGS_NO_AERSID quirks for any
hardware that needs it.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Allow root port buses to choose to skip source id matching when finding the
faulting device. Certain root port devices may return an incorrect source
ID and recommend to scan child device registers for AER notifications.
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* pci/ptm:
PCI: Add PTM clock granularity information
PCI: Add pci_enable_ptm() for drivers to enable PTM on endpoints
PCI: Add Precision Time Measurement (PTM) support
The PTM Control register (PCIe r3.1, sec 7.32.3) contains an Effective
Granularity field:
This provides information relating to the expected accuracy of the PTM
clock, but does not otherwise affect the PTM mechanism.
Set the Effective Granularity based on the PTM Root and any intervening PTM
Time Sources.
This does not set Effective Granularity for Root Complex Integrated
Endpoints because I don't know how to figure out clock granularity for
them. The spec says:
... system software must set [Effective Granularity] to the value
reported in the Local Clock Granularity field by the associated PTM
Time Source.
but I don't know how to identify the associated PTM Time Source. Normally
it's the upstream bridge, but an integrated endpoint has no upstream
bridge.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This code is not being built as a module by anyone:
obj-$(CONFIG_PCIEAER) += aerdriver.o
aerdriver-objs := aerdrv_errprint.o aerdrv_core.o aerdrv.o
drivers/pci/pcie/aer/Kconfig:config PCIEAER
drivers/pci/pcie/aer/Kconfig: bool "Root Port Advanced Error Reporting support"
Remove uses of MODULE_DESCRIPTION(), MODULE_AUTHOR(), MODULE_LICENSE(),
etc., so that when reading the driver there is no doubt it is builtin-only.
The information is preserved in comments at the top of the file.
Note that for non-modular code, module_init() translates to
device_initcall().
[bhelgaas: changelog]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Tom Long Nguyen <tom.l.nguyen@intel.com>
This code is not being built as a module by anyone:
config PCIE_PME
def_bool y
depends on PCIEPORTBUS && PM
Remove traces of modularity so that when reading the driver there is no
doubt it is builtin-only.
Also delete the .remove function, since that doesn't seem to have a
sensible use case. With "normal" endpoint drivers, we have in the past set
the suppress_bind_attrs bit to make it clear that the use of ".remove" in a
builtin driver was deleted, but here for PCI, it seems overkill to jump
through the pcie_port_service_driver and into the struct device_driver in
order to finally try and do something similar with the bind setting.
Note that for non-modular code, module_init() translates to
device_initcall().
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This code is not being built as a module by anyone:
drivers/pci/pcie/Kconfig:config PCIE_DPC
drivers/pci/pcie/Kconfig: bool "PCIe Downstream Port Containment support"
Remove uses of MODULE_DESCRIPTION(), MODULE_AUTHOR(), MODULE_LICENSE(),
etc., so that when reading the driver there is no doubt it is builtin-only.
The information is preserved in comments at the top of the file.
Note that for non-modular code, module_init() translates to
device_initcall().
[bhelgaas: changelog]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Keith Busch <keith.busch@intel.com>
CC: Mika Westerberg <mika.westerberg@linux.intel.com>
This code is not being built as a module by anyone:
pcieportdrv-y := portdrv_core.o portdrv_pci.o portdrv_bus.o
obj-$(CONFIG_PCIEPORTBUS) += pcieportdrv.o
drivers/pci/pcie/Kconfig:config PCIEPORTBUS
drivers/pci/pcie/Kconfig: bool "PCI Express Port Bus support"
Remove uses of MODULE_DESCRIPTION(), MODULE_AUTHOR(), MODULE_LICENSE(),
etc., so that when reading the driver there is no doubt it is builtin-only.
The information is preserved in comments at the top of the file.
Note that for non-modular code, MODULE_DEVICE_TABLE is a no-op and
module_init() translates to device_initcall().
[bhelgaas: changelog, remove unused DRIVER_* macros]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Tom Long Nguyen <tom.l.nguyen@intel.com>
Add an pci_enable_ptm() interface so drivers can enable PTM.
The PCI core enables PTM on PTM Roots and switches automatically, but we
don't enable PTM on endpoints unless a driver requests it.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add Precision Time Measurement (PTM) support (see PCIe r3.1, sec 6.22).
Enable PTM on PTM Root devices and switch ports. This does not enable PTM
on endpoints.
There currently are no PTM-capable devices on the market, but it is
expected to be supported by the Intel Apollo Lake platform.
[bhelgaas: complete rework]
Signed-off-by: Jonathan Yong <jonathan.yong@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* pci/aspm:
PCI/ASPM: Remove redundant check of pcie_set_clkpm
* pci/dpc:
PCI: Remove DPC tristate module option
PCI: Bind DPC to Root Ports as well as Downstream Ports
PCI: Fix whitespace in struct dpc_dev
PCI: Convert Downstream Port Containment driver to use devm_* functions
* pci/hotplug:
PCI: Allow additional bus numbers for hotplug bridges
* pci/misc:
PCI: Include <asm/dma.h> for isa_dma_bridge_buggy
PCI: Make bus_attr_resource_alignment static
MAINTAINERS: Add file patterns for PCI device tree bindings
PCI: Fix comment typo
* pci/msi:
PCI/MSI: irqchip: Fix PCI_MSI dependencies
* pci/pm:
PCI: pciehp: Ignore interrupts during D3cold
PCI: Document connection between pci_power_t and hardware PM capability
PCI: Add runtime PM support for PCIe ports
ACPI / hotplug / PCI: Runtime resume bridge before rescan
PCI: Power on bridges before scanning new devices
PCI: Put PCIe ports into D3 during suspend
PCI: Don't clear d3cold_allowed for PCIe ports
PCI / PM: Enforce type casting for pci_power_t
* pci/virtualization:
PCI: Add ACS quirk for Solarflare SFC9220
PCI: Add DMA alias quirk for Adaptec 3805
PCI: Mark Atheros AR9485 and QCA9882 to avoid bus reset
PCI: Add function 1 DMA alias quirk for Marvell 88SE9182
Change the Downstream Port Containment config type from tristate to bool.
The driver doesn't automatically load based on any rules, so it needs to be
built-in in order to bind to devices it needs to drive.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
PCIe port type values are not flags, so OR'ing them is not correct.
Previously the result was equivalent to PCIe Downstream Ports, so we were
missing binding to DPC-capable Root Ports.
Change the type to 'any' so we can bind to both port types. While this
will cause the code to check Upstream Ports, the driver won't claim them
since they are not DPC-capable.
Reported-by: Alexander Antonov <alexanderx.v.antonov@intel.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Mika Westerberg <mika.westerberg@linux.intel.com>
Use the device resource management (devm) interfaces so we don't need to
explicitly release resources on failure paths or when the driver is
removed.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Keith Busch <keith.busch@intel.com>
Add back runtime PM support for PCIe ports that was removed by
fe9a743a26 ("PCI/PM: Drop unused runtime PM support code for PCIe
ports").
We cannot enable it automatically for all ports since there have been
problems previously [1]. In summary suspended PCIe ports were not able
to deal with ACPI-based hotplug reliably. One reason why this might happen
is the fact that when a PCIe port is powered down, config space access to
the devices behind the port is not possible. If the BIOS hotplug SMI
handler assumes the port is always in D0 it will not be able to find the
hotplugged devices. To be on the safe side only enable runtime PM if the
port does not claim to support hotplug.
For PCIe ports not using hotplug, we enable and allow runtime PM
automatically. Since 'bridge_d3' can be changed any time we check this in
driver ->runtime_idle() and ->runtime_suspend() and only allow runtime
suspend if the flag is still set. Use autosuspend with default of 100ms
idle time to prevent the port from repeatedly suspending and resuming on
continuous configuration space access of devices behind the port.
The actual power transition to D3 and back is handled in the PCI core.
Idea to automatically unblock (allow) runtime PM for PCIe ports came from
Dave Airlie.
[1] https://bugzilla.kernel.org/show_bug.cgi?id=53811
This includes a fix for lockdep issue reported by Valdis Kletnieks.
Tested-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The PCI core skips bridges and ports when the system is suspended. The PCI
core checks return value of pci_has_subordinate() in pci_pm_suspend_noirq()
to skip all devices where it is non-zero (which means PCI bridges and PCIe
ports).
Since PCIe ports are never suspended in the first place, there is no need
to set d3cold_allowed for them.
Tested-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Without supporting clock PM capable, if we want to disable clkpm, we don't
need this extra check as it must already be zero for the enable argument.
And it's the same for enabling clkpm here. So let's remove this check.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* pci/hotplug:
PCI: Use cached copy of PCI_EXP_SLTCAP_HPC bit
* pci/resource:
PCI: Disable all BAR sizing for devices with non-compliant BARs
x86/PCI: Mark Broadwell-EP Home Agent 1 as having non-compliant BARs
PCI: Identify Enhanced Allocation (EA) BAR Equivalent resources in sysfs
We cache the PCI_EXP_SLTCAP_HPC bit in pci_dev->is_hotplug_bridge on device
probe, so there's no need to read it again on allocation of port service
devices.
No functional change intended.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* pci/dpc:
PCI: Add Downstream Port Containment driver
PCI: Add Downstream Port Containment portdrv service type
PCI: Widen portdrv service type from 4 bits to 8 bits
* pci/resource:
alpha/PCI: Call iomem_is_exclusive() for IORESOURCE_MEM, but not IORESOURCE_IO
PCI: Supply CPU physical address (not bus address) to iomem_is_exclusive()
* pci/thunderbolt:
thunderbolt: Fix double free of drom buffer
Add driver for the PCI Express Downstream Port Containment extended
capability. DPC is an optional capability to contain uncorrectable errors
below a port.
For more information on DPC, please see PCI Express Base Specification
Revision 4, section 7.31, or view the PCI-SIG DPC ECN here:
https://pcisig.com/sites/default/files/specification_documents/ECN_DPC_2012-02-09_finalized.pdf
When a DPC event is triggered, the hardware disables downstream links, so
the DPC driver schedules removal for all devices below this port. This may
happen concurrently with a PCIe hotplug driver if enabled. When all
downstream devices are removed and the link state transitions to disabled,
the DPC driver clears the DPC status and interrupt bits so the link may
retrain for a newly connected device.
[bhelgaas: clear (not set) DPC_CTL bits on remove, whitespace cleanup]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Lukas Wunner <lukas@wunner.de>
Add the Downstream Port Containment (PCIE_PORT_SERVICE_DPC) portdrv service
type, available if the device has the DPC extended capability.
[bhelgaas: split to separate patch, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The names of port service devices previously used one nibble to encode the
port type and another nibble to encode the service type. We're about to
add a fifth service type, so change device names to use one *byte* to
encode the service type.
For example, a hotplug port service on a downstream bridge was previously
called "pcie24" and is now called "pcie204". The "2" encodes the device
type (PCI_EXP_TYPE_DOWNSTREAM - 4), and the "4" (now "04") encodes the
service (PCIE_PORT_SERVICE_HP).
Based on Lukas Wunner's patch:
b688d6e487
[bhelgaas: split to separate patch, expand changelog]
Based-on-patch-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Now that pcie_port_acpi_setup() always returns 0, make it and its callers
void functions and stop checking the return values.
[bhelgaas: changelog]
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Host bridges we discover via ACPI, i.e., PNP0A03 and PNP0A08 devices, may
have an _OSC method by which the OS can ask the platform for control of
PCIe features like native hotplug, power management events, AER, etc.
Previously, if we found a bridge without an ACPI device, we assumed we did
not have permission to use any of these PCIe features. That seems
unreasonably restrictive.
If we find no ACPI device, assume we can take control of all PCIe features.
The Intel Volume Management Device (VMD) is one such bridge with no ACPI
device. Prior to this change, users had to boot with "pcie_ports=native"
to get hotplug and other services to work below the VMD Root Port.
[bhelgaas: changelog]
Suggested-by: Bjorn Helgaas <helgaas@kernel.org>
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* pci/aer:
PCI/AER: Log aer_inject error injections
PCI/AER: Log actual error causes in aer_inject
PCI/AER: Use dev_warn() in aer_inject
PCI/AER: Fix aer_inject error codes
* pci/enumeration:
PCI: Fix broken URL for Dell biosdevname
* pci/kconfig:
PCI: Cleanup pci/pcie/Kconfig whitespace
PCI: Include pci/hotplug Kconfig directly from pci/Kconfig
PCI: Include pci/pcie/Kconfig directly from pci/Kconfig
* pci/misc:
PCI: Add PCI_CLASS_SERIAL_USB_DEVICE definition
PCI: Add QEMU top-level IDs for (sub)vendor & device
unicore32: Remove unused HAVE_ARCH_PCI_SET_DMA_MASK definition
PCI: Consolidate PCI DMA constants and interfaces in linux/pci-dma-compat.h
PCI: Move pci_dma_* helpers to common code
frv/PCI: Remove stray pci_{alloc,free}_consistent() declaration
* pci/virtualization:
PCI: Wait for up to 1000ms after FLR reset
PCI: Support SR-IOV on any function type
* pci/vpd:
PCI: Prevent VPD access for buggy devices
PCI: Sleep rather than busy-wait for VPD access completion
PCI: Fold struct pci_vpd_pci22 into struct pci_vpd
PCI: Rename VPD symbols to remove unnecessary "pci22"
PCI: Remove struct pci_vpd_ops.release function pointer
PCI: Move pci_vpd_release() from header file to pci/access.c
PCI: Move pci_read_vpd() and pci_write_vpd() close to other VPD code
PCI: Determine actual VPD size on first access
PCI: Use bitfield instead of bool for struct pci_vpd_pci22.busy
PCI: Allow access to VPD attributes with size 0
PCI: Update VPD definitions
Clean up style issues in drivers/pci/pcie/Kconfig, in particular all
indentation is now done using tabs, not spaces, and the definition of
PCIEASPM_DEBUG is now separated from the definition of PCIEASPM with a
newline.
Signed-off-by: Andreas Ziegler <andreas.ziegler@fau.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Log successful error injections so that injected errors can be
differentiated from real errors.
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Borislav Petkov <bp@suse.de>
The aer_inject driver is very quiet. In most cases, it merely returns an
error code to user-space, leaving the user with little clue about the
actual reason for the failure.
So, log error messages for 4 of the most frequent causes of failure:
* Can't find the root port of the specified device.
* Device doesn't support AER.
* Root port doesn't support AER.
* AER device not found.
This gives the user a chance to understand why aer-inject failed.
Based on a preliminary patch by Thomas Renninger.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Borislav Petkov <bp@suse.de>
CC: Thomas Renninger <trenn@suse.de>
dev_warn() is better than printk(LOG_WARNING...) as it records which device
the message relates to. Also add a prefix "aer_inject:" to help
differentiate real errors from injected errors.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Borislav Petkov <bp@suse.de>
EPERM means "Operation not permitted", which doesn't reflect the lack of
support for AER. EPROTONOSUPPORT (Protocol not supported) is a better
choice of error code if the device or its root port lack support for AER.
Likewise, EINVAL means "Invalid argument", which is not suitable for cases
where the AER error device is missing or unusable. ENODEV and
EPROTONOSUPPORT, respectively, fit better.
Suggested-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Borislav Petkov <bp@suse.de>
CC: Prarit Bhargava <prarit@redhat.com>
* pci/aer:
PCI/AER: Use list_first_entry_or_null() to simplify code
PCI/AER: Restore pci_ops pointer while calling original pci_ops
PCI/AER: Rename pci_ops_aer to aer_inj_pci_ops
* pci/misc:
PCI: Remove includes of asm/pci-bridge.h
PCI: Remove empty asm-generic/pci-bridge.h
ARM64: PCI: Remove generated include of asm-generic/pci-bridge.h
PCI: Remove includes of empty asm-generic/pci-bridge.h
PCI: Move pci_set_flags() from asm-generic/pci-bridge.h to linux/pci.h
PCI/PME: Restructure pcie_pme_suspend() to prevent compiler warning
PCI/PME: Remove redundant port lookup
PCI: Check device_attach() return value always
* pci/virtualization:
PCI: Add ACS quirk for all Cavium devices
Previously we had this:
if (wakeup)
ret = enable_irq_wake(...);
if (!wakeup || ret)
...
"ret" is only evaluated when "wakeup" is true, and it is always initialized
in that case, but gcc isn't smart enough to figure that out and warns:
drivers/pci/pcie/pme.c:414:14: warning: 'ret' may be used uninitialized in this function [-Wmaybe-uninitialized]
Restructure the code slightly to make it easier for gcc (and maybe for
humans as well).
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com
We've already looked up srv->port a few lines earlier, and there's no need
to do it again. Remove the redundant lookup.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com
Use list_first_entry_or_null() instead of list_empty() + list_entry() to
simplify the code.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The aer_inject module intercepts config space accesses by replacing the
bus->ops pointer. If it forwards accesses to the original pci_ops, and
those original ops use bus->ops, they see the aer_pci_ops instead of their
own pci_ops, which can cause a crash.
For example, pci_generic_config_read() uses the bus->ops->map_bus pointer.
If bus->ops is set to aer_pci_ops, which doesn't supply .map_bus,
pci_generic_config_read() will dereference an invalid pointer and cause a
crash.
Temporarily restore the original bus->ops pointer while calling ops->read()
or ops->write(). Callers of these functions already hold pci_lock, which
prevents other users of bus->ops until we're finished.
[bhelgaas: changelog]
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Rename
pci_ops_aer to aer_inj_pci_ops
pci_read_aer() to aer_inj_read_config()
pci_write_aer() to aer_inj_write_config()
This is more conventional and more informative. No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
A Root Port's AER structure (rpc) contains a queue of events. aer_irq()
enqueues AER status information and schedules aer_isr() to dequeue and
process it. When we remove a device, aer_remove() waits for the queue to
be empty, then frees the rpc struct.
But aer_isr() references the rpc struct after dequeueing and possibly
emptying the queue, which can cause a use-after-free error as in the
following scenario with two threads, aer_isr() on the left and a
concurrent aer_remove() on the right:
Thread A Thread B
-------- --------
aer_irq():
rpc->prod_idx++
aer_remove():
wait_event(rpc->prod_idx == rpc->cons_idx)
# now blocked until queue becomes empty
aer_isr(): # ...
rpc->cons_idx++ # unblocked because queue is now empty
... kfree(rpc)
mutex_unlock(&rpc->rpc_mutex)
To prevent this problem, use flush_work() to wait until the last scheduled
instance of aer_isr() has completed before freeing the rpc struct in
aer_remove().
I reproduced this use-after-free by flashing a device FPGA and
re-enumerating the bus to find the new device. With SLUB debug, this
crashes with 0x6b bytes (POISON_FREE, the use-after-free magic number) in
GPR25:
pcieport 0000:00:00.0: AER: Multiple Corrected error received: id=0000
Unable to handle kernel paging request for data at address 0x27ef9e3e
Workqueue: events aer_isr
GPR24: dd6aa000 6b6b6b6b 605f8378 605f8360 d99b12c0 604fc674 606b1704 d99b12c0
NIP [602f5328] pci_walk_bus+0xd4/0x104
[bhelgaas: changelog, stable tag]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org
* pci/host-vmd:
x86/PCI: Add driver for Intel Volume Management Device (VMD)
PCI/AER: Use 32 bit PCI domain numbers
x86/PCI: Allow DMA ops specific to a PCI domain
irqdomain: Export irq_domain_set_info() for module use
genirq/MSI: Relax msi_domain_alloc() to support parentless MSI irqdomains
The Intel Volume Management Device (VMD) supports 32-bit domain numbers.
To accommodate this, use u32 instead of u16 to store domain numbers.
[bhelgaas: changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* pci/aspm:
PCI/ASPM: Make sysfs link_state_store() consistent with link_state_show()
* pci/hotplug:
PCI: pciehp: Always protect pciehp_disable_slot() with hotplug mutex
* pci/misc:
x86/PCI: Simplify pci_bios_{read,write}
PCI: Simplify config space size computation
PCI: Limit config space size for Netronome NFP6000 family
PCI: Add Netronome vendor and device IDs
PCI: Support PCIe devices with short cfg_size
x86/PCI: Clarify AMD Fam10h config access restrictions comment
PCI: Print warnings for all invalid expansion ROM headers
PCI: Check for PCI_HEADER_TYPE_BRIDGE equality, not bitmask
* pci/msi:
PCI/MSI: Remove empty pci_msi_init_pci_dev()
PCI/MSI: Initialize MSI capability for all architectures
Bit 7 of the "Header Type" register indicates a multi-function device when
set. Bits 0-6 contain encoded values, where 0x1 indicates a PCI-PCI
bridge. It is incorrect to test this as though it were a mask.
For example, while the PCI 3.0 spec only defines values 0x0, 0x1, and 0x2,
it's conceivable that a future spec could define 0x3 to mean something
else; then tests for "(hdr_type & 0x7f) & PCI_HEADER_TYPE_BRIDGE" would
incorrectly succeed for this new 0x3 header type.
Test bits 0-6 of the Header Type for equality with PCI_HEADER_TYPE_BRIDGE.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
If CONFIG_PCIEASPM_DEBUG is set, then PCI devices have a link_state
attribute. Reading that attribute shows the state as a bit mask: 1
means L0S upstream, 2 means L0S downstream, and 4 means L1.
Oddly, writing to link_state is inconsistent and gets translated, leading
to mysterious results in which the value you store isn't comparable the
value you load back out.
Fix it by making link_state_store() match link_state_show().
[bhelgaas: Check "aspm_disabled" *before* validating input. When
"aspm_disabled" is set, this changes the error for invalid input from
-EINVAL to -EPERM.]
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
AER errors might be recorded when powering-on devices. These errors can be
ignored, so firmware usually clears them before the OS enumerates devices.
However, firmware is not involved when devices are added via hotplug, so
the OS may discover power-up errors that should be ignored. The same may
happen when powering up devices when resuming after suspend.
Clear the AER error status registers during enumeration and resume.
[bhelgaas: changelog, remove repetitive comments]
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The function comment claimed this was pcie_port_device_suspend(), but it's
really pcie_port_device_resume(). Perils of cut and paste.
Use the correct function name in the comment.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Update the Link Control Enable Clock Power Management bit the same
way we update the ASPM Control bits, with a single call of
pcie_capability_clear_and_set_word().
No functional change; this just makes both paths use the same style.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Previously we assumed that PCIe Root Ports and Downstream Ports had Links
on their secondary side. That is true in most systems, but it is possible
to connect a switch with either an Upstream or a Downstream Port leading
downstream.
Instead of relying on the component type to identify devices that have
links leading downstream, use the "dev->has_secondary_link" field.
[bhelgaas: changelog]
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We allocate pcie_link_state for the component at the upstream end of a
Link. Previously we did this by allocating pcie_link_state for Root Ports
and Downstream Ports. This works fine for the typical topology:
00:1c.0 Root Port [bridge to bus 02]
02:00.0 Upstream Port [bridge to bus 03]
03:00.0 Downstream Port [bridge to bus 04]
04:00.0 Endpoint or Switch Port
However, it is possible to have a Root Port connected to a Downstream Port
instead of an Upstream Port, as in Robert White's ATCA system:
00:1c.0 Root Port [bridge to bus 02]
02:00.0 Downstream Port [bridge to bus 03]
03:01.0 Downstream Port [bridge to bus 04]
04:00.0 Endpoint or Switch Port
In this topology, we wrongly allocated pcie_link_state for the 02:00.0
Downstream Port, which is actually the *downstream* end of a link. This
led to the following NULL pointer dereference when we tried to connect this
link into the tree of links starting at the 00:1c.0 Root Port:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000088
IP: [<ffffffff81550324>] pcie_aspm_init_link_state+0x744/0x850
Hardware name: Kontron B3001/B3001, BIOS 4.6.3 08/07/2012
Call Trace:
[<ffffffff8153b865>] pci_scan_slot+0xd5/0x120
[<ffffffff8153ca1d>] pci_scan_child_bus+0x2d/0xd0
...
Instead of relying on the component type to identify the upstream end of a
link, use the "dev->has_secondary_link" field.
This means it's now possible for an Upstream Port to have a link on its
secondary side, so alloc_pcie_link_state() needs to connect links
originating from both Upstream and Downstream Ports into the tree.
[bhelgaas: changelog, add comment]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=94361
Link: http://lkml.kernel.org/r/54EB81B2.4050904@pobox.com
Reported-by: Robert White <rwhite@pobox.com>
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We decide in alloc_pcie_link_state() whether to allocate a pcie_link_state
for a device. After that, it's sufficient to check pdev->link_state. We
don't need to check the PCIe port type again.
Remove the redundant PCIe port type checking.
[bhelgaas: changelog]
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
After 387d37577f ("PCI: Don't clear ASPM bits when the FADT declares it's
unsupported"), the "force" parameter to __pci_disable_link_state() is
always "false".
Remove the "force" parameter and assume it's always false.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Communications with a hardware vendor confirm that the expected behaviour
on systems that set the FADT ASPM disable bit but which still grant full
PCIe control is for the OS to leave any BIOS configuration intact and
refuse to touch the ASPM bits. This mimics the behaviour of Windows.
Signed-off-by: Matthew Garrett <mjg59@coreos.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Commit fab4c256a5 ("PCI/AER: Add a TLP header print helper") introduced
the helper function __print_tlp_header(), but contrary to the intention,
the behaviour did change: Since we're taking the address of the parameter
t, the first 4 or 8 bytes printed will be the value of the pointer t
itself, and the remaining 12 or 8 bytes will be who-knows-what (something
from the stack).
We want to show the values of the four members of the struct
aer_header_log_regs; that can be done without ugly and error-prone casts.
On little-endian this should produce the same output as originally
intended, and since no-one has complained about getting garbage output so
far, I think big-endian should be ok too.
Fixes: fab4c256a5 ("PCI/AER: Add a TLP header print helper")
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Borislav Petkov <bp@suse.de>
CC: stable@vger.kernel.org # v3.14+
Pull kconfig updates from Michal Marek:
"Yann E Morin was supposed to take over kconfig maintainership, but
this hasn't happened. So I'm sending a few kconfig patches that I
collected:
- Fix for missing va_end in kconfig
- merge_config.sh displays used if given too few arguments
- s/boolean/bool/ in Kconfig files for consistency, with the plan to
only support bool in the future"
* 'kconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
kconfig: use va_end to match corresponding va_start
merge_config.sh: Display usage if given too few arguments
kconfig: use bool instead of boolean for type definition attributes
The functions link_state_store() and clk_ctl_store() had just subtracted
ASCII '0' from input which could lead to undesired results. Instead, use
Linux string functions to safely parse input.
[bhelgaas: check kstrtouint() return value]
Signed-off-by: Chris J Arges <chris.j.arges@canonical.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Support for keyword 'boolean' will be dropped later on.
No functional change.
Reference: http://lkml.kernel.org/r/cover.1418003065.git.cj@linux.com
Signed-off-by: Christoph Jaeger <cj@linux.com>
Signed-off-by: Michal Marek <mmarek@suse.cz>
After commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so quite a few
depend on CONFIG_PM.
Replace CONFIG_PM_RUNTIME with CONFIG_PM in the PCI core code.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If the irqchip handling the PCIe PME interrupt is not able
to enable interrupt wakeup we should properly reflect this
in the PME suspend status.
This fixes a kernel warning on resume, where it would try
to disable the irq wakeup that failed to be activated while
suspending, for example:
WARNING: CPU: 0 PID: 609 at kernel/irq/manage.c:536 irq_set_irq_wake+0xc0/0xf8()
Unbalanced IRQ 384 wake disable
Fixes: 76cde7e495 (PCI / PM: Make PCIe PME interrupts wake up from suspend-to-idle)
Reported-and-tested-by: Richard Zhu <richard.zhu@freescale.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- Rework the handling of wakeup IRQs by the IRQ core such that
all of them will be switched over to "wakeup" mode in
suspend_device_irqs() and in that mode the first interrupt
will abort system suspend in progress or wake up the system
if already in suspend-to-idle (or equivalent) without executing
any interrupt handlers. Among other things that eliminates the
wakeup-related motivation to use the IRQF_NO_SUSPEND interrupt
flag with interrupts which don't really need it and should not
use it (Thomas Gleixner and Rafael J Wysocki).
- Switch over ACPI to handling wakeup interrupts with the help
of the new mechanism introduced by the above IRQ core rework
(Rafael J Wysocki).
- Rework the core generic PM domains code to eliminate code that's
not used, add DT support and add a generic mechanism by which
devices can be added to PM domains automatically during
enumeration (Ulf Hansson, Geert Uytterhoeven and Tomasz Figa).
- Add debugfs-based mechanics for debugging generic PM domains
(Maciej Matraszek).
- ACPICA update to upstream version 20140828. Included are updates
related to the SRAT and GTDT tables and the _PSx methods are in
the METHOD_NAME list now (Bob Moore and Hanjun Guo).
- Add _OSI("Darwin") support to the ACPI core (unfortunately, that
can't really be done in a straightforward way) to prevent
Thunderbolt from being turned off on Apple systems after boot
(or after resume from system suspend) and rework the ACPI Smart
Battery Subsystem (SBS) driver to work correctly with Apple
platforms (Matthew Garrett and Andreas Noever).
- ACPI LPSS (Low-Power Subsystem) driver update cleaning up the
code, adding support for 133MHz I2C source clock on Intel Baytrail
to it and making it avoid using UART RTS override with Auto Flow
Control (Heikki Krogerus).
- ACPI backlight updates removing the video_set_use_native_backlight
quirk which is not necessary any more, making the code check the
list of output devices returned by the _DOD method to avoid
creating acpi_video interfaces that won't work and adding a quirk
for Lenovo Ideapad Z570 (Hans de Goede, Aaron Lu and Stepan Bujnak).
- New Win8 ACPI OSI quirks for some Dell laptops (Edward Lin).
- Assorted ACPI code cleanups (Fabian Frederick, Rasmus Villemoes,
Sudip Mukherjee, Yijing Wang, and Zhang Rui).
- cpufreq core updates and cleanups (Viresh Kumar, Preeti U Murthy,
Rasmus Villemoes).
- cpufreq driver updates: cpufreq-cpu0/cpufreq-dt (driver name
change among other things), ppc-corenet, powernv (Viresh Kumar,
Preeti U Murthy, Shilpasri G Bhat, Lucas Stach).
- cpuidle support for DT-based idle states infrastructure, new
ARM64 cpuidle driver, cpuidle core cleanups (Lorenzo Pieralisi,
Rasmus Villemoes).
- ARM big.LITTLE cpuidle driver updates: support for DT-based
initialization and Exynos5800 compatible string (Lorenzo Pieralisi,
Kevin Hilman).
- Rework of the test_suspend kernel command line argument and
a new trace event for console resume (Srinivas Pandruvada,
Todd E Brandt).
- Second attempt to optimize swsusp_free() (hibernation core) to
make it avoid going through all PFNs which may be way too slow on
some systems (Joerg Roedel).
- devfreq updates (Paul Bolle, Punit Agrawal, Ãrjan Eide).
- rockchip-io Adaptive Voltage Scaling (AVS) driver and AVS
entry update in MAINTAINERS (Heiko Stübner, Kevin Hilman).
- PM core fix related to clock management (Geert Uytterhoeven).
- PM core's sysfs code cleanup (Johannes Berg).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=sIv/
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"Features-wise, to me the most important this time is a rework of
wakeup interrupts handling in the core that makes them work
consistently across all of the available sleep states, including
suspend-to-idle. Many thanks to Thomas Gleixner for his help with
this work.
Second is an update of the generic PM domains code that has been in
need of some care for quite a while. Unused code is being removed, DT
support is being added and domains are now going to be attached to
devices in bus type code in analogy with the ACPI PM domain. The
majority of work here was done by Ulf Hansson who also has been the
most active developer this time.
Apart from this we have a traditional ACPICA update, this time to
upstream version 20140828 and a few ACPI wakeup interrupts handling
patches on top of the general rework mentioned above. There also are
several cpufreq commits including renaming the cpufreq-cpu0 driver to
cpufreq-dt, as this is what implements generic DT-based cpufreq
support, and a new DT-based idle states infrastructure for cpuidle.
In addition to that, the ACPI LPSS driver is updated, ACPI support for
Apple machines is improved, a few bugs are fixed and a few cleanups
are made all over.
Finally, the Adaptive Voltage Scaling (AVS) subsystem now has a tree
maintained by Kevin Hilman that will be merged through the PM tree.
Numbers-wise, the generic PM domains update takes the lead this time
with 32 non-merge commits, second is cpufreq (15 commits) and the 3rd
place goes to the wakeup interrupts handling rework (13 commits).
Specifics:
- Rework the handling of wakeup IRQs by the IRQ core such that all of
them will be switched over to "wakeup" mode in suspend_device_irqs()
and in that mode the first interrupt will abort system suspend in
progress or wake up the system if already in suspend-to-idle (or
equivalent) without executing any interrupt handlers. Among other
things that eliminates the wakeup-related motivation to use the
IRQF_NO_SUSPEND interrupt flag with interrupts which don't really
need it and should not use it (Thomas Gleixner and Rafael Wysocki)
- Switch over ACPI to handling wakeup interrupts with the help of the
new mechanism introduced by the above IRQ core rework (Rafael Wysocki)
- Rework the core generic PM domains code to eliminate code that's
not used, add DT support and add a generic mechanism by which
devices can be added to PM domains automatically during enumeration
(Ulf Hansson, Geert Uytterhoeven and Tomasz Figa).
- Add debugfs-based mechanics for debugging generic PM domains
(Maciej Matraszek).
- ACPICA update to upstream version 20140828. Included are updates
related to the SRAT and GTDT tables and the _PSx methods are in the
METHOD_NAME list now (Bob Moore and Hanjun Guo).
- Add _OSI("Darwin") support to the ACPI core (unfortunately, that
can't really be done in a straightforward way) to prevent
Thunderbolt from being turned off on Apple systems after boot (or
after resume from system suspend) and rework the ACPI Smart Battery
Subsystem (SBS) driver to work correctly with Apple platforms
(Matthew Garrett and Andreas Noever).
- ACPI LPSS (Low-Power Subsystem) driver update cleaning up the code,
adding support for 133MHz I2C source clock on Intel Baytrail to it
and making it avoid using UART RTS override with Auto Flow Control
(Heikki Krogerus).
- ACPI backlight updates removing the video_set_use_native_backlight
quirk which is not necessary any more, making the code check the
list of output devices returned by the _DOD method to avoid
creating acpi_video interfaces that won't work and adding a quirk
for Lenovo Ideapad Z570 (Hans de Goede, Aaron Lu and Stepan Bujnak)
- New Win8 ACPI OSI quirks for some Dell laptops (Edward Lin)
- Assorted ACPI code cleanups (Fabian Frederick, Rasmus Villemoes,
Sudip Mukherjee, Yijing Wang, and Zhang Rui)
- cpufreq core updates and cleanups (Viresh Kumar, Preeti U Murthy,
Rasmus Villemoes)
- cpufreq driver updates: cpufreq-cpu0/cpufreq-dt (driver name change
among other things), ppc-corenet, powernv (Viresh Kumar, Preeti U
Murthy, Shilpasri G Bhat, Lucas Stach)
- cpuidle support for DT-based idle states infrastructure, new ARM64
cpuidle driver, cpuidle core cleanups (Lorenzo Pieralisi, Rasmus
Villemoes)
- ARM big.LITTLE cpuidle driver updates: support for DT-based
initialization and Exynos5800 compatible string (Lorenzo Pieralisi,
Kevin Hilman)
- Rework of the test_suspend kernel command line argument and a new
trace event for console resume (Srinivas Pandruvada, Todd E Brandt)
- Second attempt to optimize swsusp_free() (hibernation core) to make
it avoid going through all PFNs which may be way too slow on some
systems (Joerg Roedel)
- devfreq updates (Paul Bolle, Punit Agrawal, Ãrjan Eide).
- rockchip-io Adaptive Voltage Scaling (AVS) driver and AVS entry
update in MAINTAINERS (Heiko Stübner, Kevin Hilman)
- PM core fix related to clock management (Geert Uytterhoeven)
- PM core's sysfs code cleanup (Johannes Berg)"
* tag 'pm+acpi-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (105 commits)
ACPI / fan: printk replacement
PM / clk: Fix crash in clocks management code if !CONFIG_PM_RUNTIME
PM / Domains: Rename cpu_data to cpuidle_data
cpufreq: cpufreq-dt: fix potential double put of cpu OF node
cpufreq: cpu0: rename driver and internals to 'cpufreq_dt'
PM / hibernate: Iterate over set bits instead of PFNs in swsusp_free()
cpufreq: ppc-corenet: remove duplicate update of cpu_data
ACPI / sleep: Rework the handling of ACPI GPE wakeup from suspend-to-idle
PM / sleep: Rename platform suspend/resume functions in suspend.c
PM / sleep: Export dpm_suspend_late/noirq() and dpm_resume_early/noirq()
ACPICA: Introduce acpi_enable_all_wakeup_gpes()
ACPICA: Clear all non-wakeup GPEs in acpi_hw_enable_wakeup_gpe_block()
ACPI / video: check _DOD list when creating backlight devices
PM / Domains: Move dev_pm_domain_attach|detach() to pm_domain.h
cpufreq: Replace strnicmp with strncasecmp
cpufreq: powernv: Set the cpus to nominal frequency during reboot/kexec
cpufreq: powernv: Set the pstate of the last hotplugged out cpu in policy->cpus to minimum
cpufreq: Allow stop CPU callback to be used by all cpufreq drivers
PM / devfreq: exynos: Enable building exynos PPMU as module
PM / devfreq: Export helper functions for drivers
...
Add strings for all AER error bits defined in PCIe r3.0.
[bhelgaas: changelog, drop designated initializer change]
Signed-off-by: Chen, Gong <gong.chen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Since commit de7d5f729c ("PCI/PM: Disable runtime PM of PCIe ports") the
runtime PM support code for PCIe ports in portdrv_pci.c has never been
used, so drop it entirely.
If we are to support runtime PM of PCIe ports, it will have to be done in a
different way most likely anyway.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
To make PCIe PME interrupts wake up the system from suspend to idle,
make the PME driver use enable_irq_wake() on the IRQ during system
suspend (if there are any wakeup devices below the given PCIe port)
without disabling PME interrupts. This way, an interrupt will still
trigger if a wakeup event happens and the system will be woken up (or
system suspend in progress will be aborted) by means of the new
mechanics introduced previously.
This change allows Wake-on-LAN to be used for wakeup from
suspend-to-idle on my MSI Wind tesbed netbook.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull RAS updates from Ingo Molnar:
"The main changes in this cycle are:
- RAS tracing/events infrastructure, by Gong Chen.
- Various generalizations of the APEI code to make it available to
non-x86 architectures, by Tomasz Nowicki"
* 'x86-ras-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/ras: Fix build warnings in <linux/aer.h>
acpi, apei, ghes: Factor out ioremap virtual memory for IRQ and NMI context.
acpi, apei, ghes: Make NMI error notification to be GHES architecture extension.
apei, mce: Factor out APEI architecture specific MCE calls.
RAS, extlog: Adjust init flow
trace, eMCA: Add a knob to adjust where to save event log
trace, RAS: Add eMCA trace event interface
RAS, debugfs: Add debugfs interface for RAS subsystem
CPER: Adjust code flow of some functions
x86, MCE: Robustify mcheck_init_device
trace, AER: Move trace into unified interface
trace, RAS: Add basic RAS trace event
x86, MCE: Kill CPU_POST_DEAD
For hot-added PCIe ports on x86 platforms, we always warned about an
invalid IRQ, e.g.,
pci 0000:00:00.0: device [8086:0e0b] has invalid IRQ; check vendor BIOS
This was because we check pci_dev->irq before actually allocating the IRQ
for the device, which happens in this path:
pcie_port_device_register
pci_enable_device
pci_enable_device_flags
do_pci_enable_device
pcibios_enable_device (on x86)
pcibios_enable_irq
This warning message isn't generated for PCIe ports present at boot time
because x86 arch code has called acpi_pci_irq_enable() in pci_acpi_init()
for each PCI device for safety.
[bhelgaas: changelog]
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
AER uses a separate trace interface by now. To make it
consistent, move it into unified RAS trace interface.
Signed-off-by: Chen, Gong <gong.chen@linux.intel.com>
Acked-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Merge quoted strings that are broken across lines into a single entity.
The compiler merges them anyway, but checkpatch complains about it, and
merging them makes it easier to grep for strings.
No functional change.
[bhelgaas: changelog, do the same for everything under drivers/pci]
Signed-off-by: Ryan Desfosses <ryan@desfo.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Fix various whitespace errors.
No functional change.
[bhelgaas: fix other similar problems]
Signed-off-by: Ryan Desfosses <ryan@desfo.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* pci/hotplug:
PCI: rphahp: Fix endianess issues
PCI: Allow hotplug service drivers to operate in polling mode
PCI: pciehp: Acknowledge spurious "cmd completed" event
PCI: pciehp: Use PCI_EXP_SLTCAP_PSN define
PCI: hotplug: Remove unnecessary "dev->bus" test
* pci/msi:
GenWQE: Use pci_enable_msi_exact() instead of pci_enable_msi_block()
PCI/MSI: Simplify populate_msi_sysfs()
PCI/portdrv: Use pci_enable_msix_exact() instead of pci_enable_msix()
* pci/virtualization:
PCI: Add Patsburg (X79) to Intel PCH root port ACS quirk
* pci/misc:
PCI: Fix use of uninitialized MPS value
PCI: Remove dead code
MAINTAINERS: Add arch/x86/kernel/quirks.c to PCI file patterns
PCI: Remove unnecessary __ref annotations
PCI: Fail new_id for vendor/device values already built into driver
PCI: Add new ID for Intel GPU "spurious interrupt" quirk
PCI: Update my email address
PCI: Fix incorrect vgaarb conditional in WARN_ON()
PCI: Use designated initialization in PCI_VDEVICE
PCI: Remove old serial device IDs
PCI: Remove unnecessary includes of <linux/init.h>
powerpc/PCI: Fix NULL dereference in sys_pciconfig_iobase() list traversal
Today the PCIe port bus driver disables the Hot-plug service if the port
device does not have the capability to generate interrupts. However, a
user must be able to use the "pciehp_poll_mode" parameter to use the pciehp
in polling method in such a case. Today it is not possible.
This patch allows a hotplug service driver to decide whether or not it
would like to continue in the absence of interrupts.
Signed-off-by: Rajat Jain <rajatxjain@gmail.com>
Signed-off-by: Rajat Jain <rajatjain@juniper.net>
Signed-off-by: Guenter Roeck <groeck@juniper.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers using these two
interfaces need to be updated to use the new pci_enable_msi_range() or
pci_enable_msi_exact() and pci_enable_msix_range() or
pci_enable_msix_exact() interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* pci/aer:
PCI/AER: Support ACPI HEST AER error sources for PCI domains other than 0
ACPICA: Add helper macros to extract bus/segment numbers from HEST table.
In the discussion for this set of patches [link below], Bjorn Helgaas
pointed out that the ACPI HEST AER error sources do not have the PCIe
segment number associated with the bus. I worked with the ACPI spec and
got this change to definition of the "Bus" field into the recently released
ACPI Spec 5.0a section 18.3.2.3-5:
Identifies the PCI Bus and Segment of the device. The Bus is encoded in
bits 0-7. For systems that expose multiple PCI segment groups, the
segment number is encoded in bits 8-23 and bits 24-31 must be zero. For
systems that do not expose multiple PCI segment groups, bits 8-31 must be
zero. If the GLOBAL flag is specified, this field is ignored.
This patch makes use of the new definition in the only place in the kernel
that uses the acpi_hest_aer_common's bus field.
This depends on 36f3615152 ("ACPICA: Add helper macros to extract
bus/segment numbers from HEST table.")
Link: http://lkml.kernel.org/r/1370542251-27387-1-git-send-email-betty.dall@hp.com
Signed-off-by: Betty Dall <betty.dall@hp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
My philosophy is unused code is dead code. And dead code is subject to bit
rot and is a likely source of bugs. Use it or lose it.
This reverts part of 3e1b16002a ("ACPI/PCI: PCIe ASPM _OSC support
capabilities called when root bridge added"), removing this interface:
pcie_aspm_enabled()
[bhelgaas: split to separate patch]
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Andrew Patterson <andrew.patterson@hp.com>
This creates an MSI-X counterpart for pci_msi_vec_count(). Device drivers
can use this function to obtain maximum number of MSI-X interrupts the
device supports and use that number in a subsequent call to
pci_enable_msix().
pci_msix_vec_count() supersedes pci_msix_table_size() and returns a
negative errno if device does not support MSI-X interrupts. After this
update, callers must always check the returned value.
The only user of pci_msix_table_size() was the PCI-Express port driver,
which is also updated by this change.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Tejun Heo <tj@kernel.org>
Previously pcie_device_init() called get_device() if device_register() for
the new pcie_device succeeded, and remove_iter() called put_device() when
removing before unregistering the device.
But device_register() already increments the reference count in
device_add(), so we don't need to do it again here.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This is required so that we give up the last reference to the device.
Removed the kfree() as put_device will result in release_pcie_device()
being called and hence the container of the device will be kfree'd.
[bhelgaas: fix conflict after my previous cleanup]
Signed-off-by: Levente Kurusa <levex@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Make the straightline path the normal no-error path. Check for errors and
return them directly, instead of checking for success and putting the
normal path in an "if" body.
No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>