Instead of fetching dma address from rx_desc->data[0].addr,
prefer using frags[0].dma + frags[0].page_offset to avoid
a potential cache line miss.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This new counter tracks number of pages that we allocated for one port.
lpaa24:~# ethtool -S eth0 | egrep 'rx_alloc_pages|rx_packets'
rx_packets: 306755183
rx_alloc_pages: 932897
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Same technique than some Intel drivers, for arches where PAGE_SIZE = 4096
In most cases, pages are reused because they were consumed
before we could loop around the RX ring.
This brings back performance, and is even better,
a single TCP flow reaches 30Gbit on my hosts.
v2: added full memset() in mlx4_en_free_frag(), as Tariq found it was needed
if we switch to large MTU, as priv->log_rx_info can dynamically be changed.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use of order-3 pages is problematic in some cases.
This patch might add three kinds of regression :
1) a CPU performance regression, but we will add later page
recycling and performance should be back.
2) TCP receiver could grow its receive window slightly slower,
because skb->len/skb->truesize ratio will decrease.
This is mostly ok, we prefer being conservative to not risk OOM,
and eventually tune TCP better in the future.
This is consistent with other drivers using 2048 per ethernet frame.
3) Because we allocate one page per RX slot, we consume more
memory for the ring buffers. XDP already had this constraint anyway.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We will soon use order-0 pages, and frag truesize will more precisely
match real sizes.
In the new model, we prefer to use <= 2048 bytes fragments, so that
we can use page-recycle technique on PAGE_SIZE=4096 arches.
We will still pack as much frames as possible on arches with big
pages, like PowerPC.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We only need to store the page and dma address.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to duplicate it per RX queue / frags.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using per frag storage for frag_prefix_size is really silly.
mlx4_en_complete_rx_desc() has all needed info already.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is really a port attribute, no need to duplicate it per
RX queue and per frag.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to duplicate it for all queues and frags.
num_frags & log_rx_info become u8 to save space.
u8 accesses are a bit faster than u16 anyway.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The overrun ignore bit isn't supported by the device's firmware and was
recently removed from the programmer's reference manual (PRM).
Remove it from the driver as well.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit dd82364c3a ("mlxsw: Flip to the new dev walk API") did some
small changes in mlxsw code, but it did not respect the naming
conventions. So fix this now.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This warnings may be hit even in case they should not - in case user
puts a TC-flower rule which failed to be offloaded. So just remove them.
Reported-by: Petr Machata <petrm@mellanox.com>
Reported-by: Ido Schimmel <idosch@mellanox.com>
Fixes: commit 7aa0f5aa90 ("mlxsw: spectrum: Implement TC flower offload")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the setup_tc ndo to configure prioritised Tx traffic classes.
Priorities range from 0 (lowest) to 3 (highest). The driver assigns
NR_CPUS queues to each traffic class.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Each traffic class corresponds to a WQ priority level. The number of Tx
netdev queues and frame queues is increased to NR_CPUS queues for each
traffic class. In addition, the priority of the Rx, Error and Conf queues
is lowered but their order is maintained.
By default, only one traffic class is enabled, only the low priority Tx
queues are used and only the corresponding netdev queues are advertised.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Tested-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Margetson reported a panic on his SAM460EX with Kernel 4.11-rc1:
| Unable to handle kernel paging request for data at address 0x00000014
| Oops: Kernel access of bad area, sig: 11 [#1]
| PREEMPT
| Canyonlands
| Modules linked in:
| CPU: 0 PID: 1 Comm: swapper Not tainted [...]
| task: ea838000 task.stack: ea836000
| NIP: c0599f5c LR: c0599dd8 CTR: 00000000
| REGS: ea837c80 TRAP: 0300 Not tainted [...]
| MSR: 00029000 <CE,EE,ME>
| CR: 24371242 XER: 20000000
| DEAR: 00000014 ESR: 00000000
| GPR00: c0599ce8 ea837d30 ea838000 c0e52dcc c0d56ffb [...]
| NIP [c0599f5c] emac_probe+0xfb4/0x1304
| LR [c0599dd8] emac_probe+0xe30/0x1304
| Call Trace:
| [ea837d30] [c0599ce8] emac_probe+0xd40/0x1304 (unreliable)
| [ea837d80] [c0533504] platform_drv_probe+0x48/0x90
| [ea837da0] [c0531c14] driver_probe_device+0x15c/0x2c4
| [ea837dd0] [c0531e04] __driver_attach+0x88/0xb0
| ---[ end trace ... ]---
The problem is caused by emac_dt_phy_probe() returing success (0)
for existing device-trees configurations that do not specify a
"phy-handle" property. This caused the code to skip the existing
phy probe and setup. Which led to essential phy related
data-structures being uninitialized.
This patch also removes the unused variable in emac_dt_phy_connect().
Fixes: a577ca6bad ("net: emac: add support for device-tree based PHY discovery and setup")
Reported-by: Julian Margetson <runaway@candw.ms>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Tested-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The amount of TX/RX buffers that the vNIC driver currently allocates
is different from the amount agreed upon in negotiation with firmware.
Correct that by allocating the requested number of buffers confirmed
by firmware.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a counter to track the number of outstanding transmissions sent
that have not received completions. If the counter reaches the maximum
number of queue entries, stop transmissions on that queue. As we receive
more completions from firmware, wake the queue once the counter reaches
an acceptable level.
This patch prevents hardware/firmware TX queue from filling up and
and generating errors. Since incorporating this fix, internal testing
has reported that these firmware errors have stopped.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Configuring VLANs from the VF side had no effect, because the PF ignored
filters of type VFPF_VLAN_FILTER in the VF-PF message.
Add the missing filter type to configure.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
filters->count is the number of filters we were supposed to configure.
There is no reason to increase it by +1 when printing the count in an error
message.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On failure to configure a VF MAC/VLAN filter we should not attempt to
rollback filters that we failed to configure with -EEXIST.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VFs are currently missing the VLAN filtering feature, because we were
checking the PF's acquire response before actually performing the acquire.
Fix it by setting the feature flag later when we have the PF response.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is too late to check for the limit of the number of VF multicast
addresses after they have already been copied to the req->multicast[]
array, possibly overflowing it.
Do the check before copying.
Also fix the error path to not skip unlocking vf2pf_mutex.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When BNX2X_MSG_IOV is enabled, the driver produces too many VF statistics
messages. Lower the verbosity of the VF stats messages similarly as in
commit 76ca70fabb ("bnx2x: [Debug] change verbosity of some prints").
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible to crash the kernel by accessing a PTP device while its
associated bnx2x interface is down. Before the interface is brought up,
the timecounter is not initialized, so accessing it results in NULL
dereference.
Fix it by checking if the interface is up.
Use -ENETDOWN as the error code when the interface is down.
-EFAULT in bnx2x_ptp_adjfreq() did not seem right.
Tested using phc_ctl get/set/adj/freq commands.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adjust the impedance values of the RX and TX lanes in the SGMII block
so that they are closer to optimal values.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethernet support now calls directly into the ipv6 core code, which
fails if IPV6 is a loadable module but mlx5 is built-in:
drivers/net/ethernet/mellanox/mlx5/core/en_tc.o: In function `mlx5e_create_encap_header_ipv6':
en_tc.c:(.text.mlx5e_create_encap_header_ipv6+0x110): undefined reference to `ip6_route_output_flags'
This adds a dependency to ensure that MLX5_CORE_EN can only be built
if we are able link the kernel successfully. The downside is that the
ethernet option can be hidden. Alternatively we could make MLX5_CORE
depend on "IPV6 || !IPV6", which would force MLX5_CORE to be a module
when IPV6 is, including in configurations where we don't use the ethernet
support at all.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement suspend/resume callbacks in the bgmac driver. This makes sure
that we de-initialize and re-initialize the hardware correctly before
entering suspend and when resuming.
Signed-off-by: Joey Zhong <zhongx@broadcom.com>
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BCM471X and BCM535X are of the same family (from what I can derive from
internal documents). Group them into the case statement together, which
results in more code reuse.
Also, use existing helper variables to make the code a little more
readable too.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The maximum frame size is really just the standard ethernet frame size
and FCS. So use those existing defines to make the code a little more
beautiful.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use eth_hw_addr_random() to set a random MAC address in order to make
sure ndev->addr_assign_type will be properly set to NET_ADDR_RANDOM.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix double-free in batman-adv, from Sven Eckelmann.
2) Fix packet stats for fast-RX path, from Joannes Berg.
3) Netfilter's ip_route_me_harder() doesn't handle request sockets
properly, fix from Florian Westphal.
4) Fix sendmsg deadlock in rxrpc, from David Howells.
5) Add missing RCU locking to transport hashtable scan, from Xin Long.
6) Fix potential packet loss in mlxsw driver, from Ido Schimmel.
7) Fix race in NAPI handling between poll handlers and busy polling,
from Eric Dumazet.
8) TX path in vxlan and geneve need proper RCU locking, from Jakub
Kicinski.
9) SYN processing in DCCP and TCP need to disable BH, from Eric
Dumazet.
10) Properly handle net_enable_timestamp() being invoked from IRQ
context, also from Eric Dumazet.
11) Fix crash on device-tree systems in xgene driver, from Alban Bedel.
12) Do not call sk_free() on a locked socket, from Arnaldo Carvalho de
Melo.
13) Fix use-after-free in netvsc driver, from Dexuan Cui.
14) Fix max MTU setting in bonding driver, from WANG Cong.
15) xen-netback hash table can be allocated from softirq context, so use
GFP_ATOMIC. From Anoob Soman.
16) Fix MAC address change bug in bgmac driver, from Hari Vyas.
17) strparser needs to destroy strp_wq on module exit, from WANG Cong.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (69 commits)
strparser: destroy workqueue on module exit
sfc: fix IPID endianness in TSOv2
sfc: avoid max() in array size
rds: remove unnecessary returned value check
rxrpc: Fix potential NULL-pointer exception
nfp: correct DMA direction in XDP DMA sync
nfp: don't tell FW about the reserved buffer space
net: ethernet: bgmac: mac address change bug
net: ethernet: bgmac: init sequence bug
xen-netback: don't vfree() queues under spinlock
xen-netback: keep a local pointer for vif in backend_disconnect()
netfilter: nf_tables: don't call nfnetlink_set_err() if nfnetlink_send() fails
netfilter: nft_set_rbtree: incorrect assumption on lower interval lookups
netfilter: nf_conntrack_sip: fix wrong memory initialisation
can: flexcan: fix typo in comment
can: usb_8dev: Fix memory leak of priv->cmd_msg_buffer
can: gs_usb: fix coding style
can: gs_usb: Don't use stack memory for USB transfers
ixgbe: Limit use of 2K buffers on architectures with 256B or larger cache lines
ixgbe: update the rss key on h/w, when ethtool ask for it
...
Pull sched.h split-up from Ingo Molnar:
"The point of these changes is to significantly reduce the
<linux/sched.h> header footprint, to speed up the kernel build and to
have a cleaner header structure.
After these changes the new <linux/sched.h>'s typical preprocessed
size goes down from a previous ~0.68 MB (~22K lines) to ~0.45 MB (~15K
lines), which is around 40% faster to build on typical configs.
Not much changed from the last version (-v2) posted three weeks ago: I
eliminated quirks, backmerged fixes plus I rebased it to an upstream
SHA1 from yesterday that includes most changes queued up in -next plus
all sched.h changes that were pending from Andrew.
I've re-tested the series both on x86 and on cross-arch defconfigs,
and did a bisectability test at a number of random points.
I tried to test as many build configurations as possible, but some
build breakage is probably still left - but it should be mostly
limited to architectures that have no cross-compiler binaries
available on kernel.org, and non-default configurations"
* 'WIP.sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (146 commits)
sched/headers: Clean up <linux/sched.h>
sched/headers: Remove #ifdefs from <linux/sched.h>
sched/headers: Remove the <linux/topology.h> include from <linux/sched.h>
sched/headers, hrtimer: Remove the <linux/wait.h> include from <linux/hrtimer.h>
sched/headers, x86/apic: Remove the <linux/pm.h> header inclusion from <asm/apic.h>
sched/headers, timers: Remove the <linux/sysctl.h> include from <linux/timer.h>
sched/headers: Remove <linux/magic.h> from <linux/sched/task_stack.h>
sched/headers: Remove <linux/sched.h> from <linux/sched/init.h>
sched/core: Remove unused prefetch_stack()
sched/headers: Remove <linux/rculist.h> from <linux/sched.h>
sched/headers: Remove the 'init_pid_ns' prototype from <linux/sched.h>
sched/headers: Remove <linux/signal.h> from <linux/sched.h>
sched/headers: Remove <linux/rwsem.h> from <linux/sched.h>
sched/headers: Remove the runqueue_is_locked() prototype
sched/headers: Remove <linux/sched.h> from <linux/sched/hotplug.h>
sched/headers: Remove <linux/sched.h> from <linux/sched/debug.h>
sched/headers: Remove <linux/sched.h> from <linux/sched/nohz.h>
sched/headers: Remove <linux/sched.h> from <linux/sched/stat.h>
sched/headers: Remove the <linux/gfp.h> include from <linux/sched.h>
sched/headers: Remove <linux/rtmutex.h> from <linux/sched.h>
...
The value we read from the header is in network byte order, whereas
EFX_POPULATE_QWORD_* takes values in host byte order (which it then
converts to little-endian, as MCDI is little-endian).
Fixes: e9117e5099 ("sfc: Firmware-Assisted TSO version 2")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It confuses sparse, which thinks the size isn't constant. Let's achieve
the same thing with a BUILD_BUG_ON, since we know which one should be
bigger and don't expect them ever to change.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dma_sync_single_for_*() takes the direction in which the buffer
was mapped, not the direction of the sync. We should sync XDP
buffers bidirectionally.
Fixes: ecd63a0217 ("nfp: add XDP support in the driver")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit c0f031bc88 ("nfp_net: use alloc_frag() and build_skb()")
we are allocating buffers which have to hold both the data and skb to
be created in place by build_skb().
FW should only be told about the buffer space it can DMA to, that
is without the build_skb() headroom and tailroom. Note: firmware
applications should validate the buffers against both MTU and
free list buffer size so oversized packets would not pass through
the NIC anyway.
Fixes: c0f031bc88 ("nfp: use alloc_frag() and build_skb()")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ndo_set_mac_address() passes struct sockaddr * as 2nd parameter to
bgmac_set_mac_address() but code assumed u8 *. This caused two bytes
chopping and the wrong mac address was configured.
Signed-off-by: Hari Vyas <hariv@broadcom.com>
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Fixes: 4e209001b8 ("bgmac: write mac address to hardware in ndo_set_mac_address")
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a bug in the 'bgmac' driver init sequence that blind writes for init
sequence where it should preserve most bits other than the ones it is
deliberately manipulating.
The code now checks to see if the adapter needs to be brought out of
reset (where as before it was doing an IDM write to bring it out of
reset regardless of whether it was in reset or not). Also, removed
unnecessary usleeps (as there is already a read present to flush the
IDM writes).
Signed-off-by: Zac Schroff <zschroff@broadcom.com>
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Fixes: f6a95a2495 ("net: ethernet: bgmac: Add platform device support")
Signed-off-by: David S. Miller <davem@davemloft.net>
On architectures that have a cache line size larger than 64 Bytes we start
running into issues where the amount of headroom for the frame starts
shrinking.
The size of skb_shared_info on a system with a 64B L1 cache line size is
320. This increases to 384 with a 128B cache line, and 512 with a 256B
cache line.
In addition the NET_SKB_PAD value increases as well consistent with the
cache line size. As a result when we get to a 256B cache line as seen on
the s390 we end up 768 bytes used by padding and shared info leaving us
with only 1280 bytes to use for data storage. On architectures such as
this we should default to using 3K Rx buffers out of a 8K page instead of
trying to do 1.5K buffers out of a 4K page.
To take all of this into account I have added one small check so that we
compare the max_frame to the amount of actual data we can store. This was
already occurring for igb, but I had overlooked it for ixgbe as it doesn't
have strict limits for 82599 once we enable jumbo frames. By adding this
check we will automatically enable 3K Rx buffers as soon as the maximum
frame size we can handle drops below the standard Ethernet MTU.
I also went through and fixed one small typo that I found where I had left
an IGB in a variable name due to a copy/paste error.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently ixgbe_set_rxfh() updates the rss_key copy in the driver
memory, but does not push the new value into the h/w. This commit
add a new helper for the latter operation and call it in
ixgbe_set_rxfh(), so that the h/w rss key value can be really
updated via ethtool.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Pull SCSI target updates from Nicholas Bellinger:
"The highlights this round include:
- enable dual mode (initiator + target) qla2xxx operation. (Quinn +
Himanshu)
- add a framework for qla2xxx async fabric discovery. (Quinn +
Himanshu)
- enable iscsi PDU DDP completion offload in cxgbit/T6 NICs. (Varun)
- fix target-core handling of aborted failed commands. (Bart)
- fix a long standing target-core issue NULL pointer dereference with
active I/O LUN shutdown. (Rob Millner + Bryant + nab)"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (44 commits)
target: Add counters for ABORT_TASK success + failure
iscsi-target: Fix early login failure statistics misses
target: Fix NULL dereference during LUN lookup + active I/O shutdown
target: Delete tmr from list before processing
target: Fix handling of aborted failed commands
uapi: fix linux/target_core_user.h userspace compilation errors
target: export protocol identifier
qla2xxx: Fix a warning reported by the "smatch" static checker
target/iscsi: Fix unsolicited data seq_end_offset calculation
target/cxgbit: add T6 iSCSI DDP completion feature
target/cxgbit: Enable DDP for T6 only if data sequence and pdu are in order
target/cxgbit: Use T6 specific macros to get ETH/IP hdr len
target/cxgbit: use cxgb4_tp_smt_idx() to get smt idx
target/iscsi: split iscsit_check_dataout_hdr()
target: Remove command flag CMD_T_DEV_ACTIVE
target: Remove command flag CMD_T_BUSY
target: Move session check from target_put_sess_cmd() into target_release_cmd_kref()
target: Inline transport_cmd_check_stop()
target: Remove an overly chatty debug message
target: Stop execution if CMD_T_STOP has been set
...
Even if bus is not hot-pluggable, devices can be unbound from the
driver via sysfs, so we should not be using __exit annotations on
remove() methods. The only exception is drivers registered with
platform_driver_probe() which specifically disables sysfs bind/unbind
attributes.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change t4fw_version.h to update latest firmware version
number to 1.16.33.0.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an SFP module is not present, xgbe_phy_sfp_phy_settings() should
return after applying the default settings. Currently there is no return
statement and the default settings are overwritten.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MDIO register mode is set when the device is probed. But when the
device is brought down and then back up, the MDIO register mode has been
reset. Be sure to reset the mode during device startup and only change
the mode of the address specified.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some configurations require the use of the hardware's MDIO support to
communicate with external PHYs. The MDIO commands indicate completion
through the device interrupt. When bringing down the device the interrupts
were released before stopping the external PHY, resulting in MDIO command
timeouts. Move the stopping of the PHY to before the releasing of the
interrupts.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On DT systems the driver require a clock, but the probe just print a
warning and continue, leading to a crash when resetting the device.
To fix this crash and properly handle probe deferals only ignore the
missing clock if DT isn't used or if the clock doesn't exist.
Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
Acked-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix up affected files that include this signal functionality via sched.h.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
When the structure of the LPM tree changes (f.e., due to the addition of
a new prefix), we unbind the old tree and then bind the new one. This
may result in temporary packet loss.
Instead, overwrite the old binding with the new one.
Fixes: 6b75c4807d ("mlxsw: spectrum_router: Add virtual router management")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Don't save TIPC header values before the header has been validated,
from Jon Paul Maloy.
2) Fix memory leak in RDS, from Zhu Yanjun.
3) We miss to initialize the UID in the flow key in some paths, from
Julian Anastasov.
4) Fix latent TOS masking bug in the routing cache removal from years
ago, also from Julian.
5) We forget to set the sockaddr port in sctp_copy_local_addr_list(),
fix from Xin Long.
6) Missing module ref count drop in packet scheduler actions, from
Roman Mashak.
7) Fix RCU annotations in rht_bucket_nested, from Herbert Xu.
8) Fix use after free which happens because L2TP's ipv4 support returns
non-zero values from it's backlog_rcv function which ipv4 interprets
as protocol values. Fix from Paul Hüber.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (35 commits)
qed: Don't use attention PTT for configuring BW
qed: Fix race with multiple VFs
l2tp: avoid use-after-free caused by l2tp_ip_backlog_recv
xfrm: provide correct dst in xfrm_neigh_lookup
rhashtable: Fix RCU dereference annotation in rht_bucket_nested
rhashtable: Fix use before NULL check in bucket_table_free
net sched actions: do not overwrite status of action creation.
rxrpc: Kernel calls get stuck in recvmsg
net sched actions: decrement module reference count after table flush.
lib: Allow compile-testing of parman
ipv6: check sk sk_type and protocol early in ip_mroute_set/getsockopt
sctp: set sin_port for addr param when checking duplicate address
net/mlx4_en: fix overflow in mlx4_en_init_timestamp()
netfilter: nft_set_bitmap: incorrect bitmap size
net: s2io: fix typo argumnet argument
net: vxge: fix typo argumnet argument
netfilter: nf_ct_expect: Change __nf_ct_expect_check() return value.
ipv4: mask tos for input route
ipv4: add missing initialization for flowi4_uid
lib: fix spelling mistake: "actualy" -> "actually"
...
Now that %z is standartised in C99 there is no reason to support %Z.
Unlike %L it doesn't even make format strings smaller.
Use BUILD_BUG_ON in a couple ATM drivers.
In case anyone didn't notice lib/vsprintf.o is about half of SLUB which
is in my opinion is quite an achievement. Hopefully this patch inspires
someone else to trim vsprintf.c more.
Link: http://lkml.kernel.org/r/20170103230126.GA30170@avx2
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix typos and add the following to the scripts/spelling.txt:
overwritting||overwriting
Link: http://lkml.kernel.org/r/1481573103-11329-29-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix typos and add the following to the scripts/spelling.txt:
omited||omitted
omiting||omitting
Link: http://lkml.kernel.org/r/1481573103-11329-26-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix typos and add the following to the scripts/spelling.txt:
applys||applies
The "applyes" in drivers/video/fbdev/aty/radeon_monitor.c is a different
pattern but it was fixed in this commit. The "This functions" in the
same line was fixed as well.
Link: http://lkml.kernel.org/r/1481573103-11329-24-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix typos and add the following to the scripts/spelling.txt:
overrided||overridden
Link: http://lkml.kernel.org/r/1481573103-11329-22-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix typos and add the following to the scripts/spelling.txt:
comsume||consume
comsumer||consumer
comsuming||consuming
I see some variable names with this pattern, but this commit is only
touching comment blocks to avoid unexpected impact.
Link: http://lkml.kernel.org/r/1481573103-11329-19-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix typos and add the following to the scripts/spelling.txt:
initialiazation||initialization
While we are here, fix the "overriden" in the touched line in
drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c.
Link: http://lkml.kernel.org/r/1481573103-11329-17-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix typos and add the following to the scripts/spelling.txt:
varible||variable
While we are here, tidy up the comment blocks that fit in a single line
for drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c and
net/sctp/transport.c.
Link: http://lkml.kernel.org/r/1481573103-11329-11-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix typos and add the following to the scripts/spelling.txt:
partiton||partition
Link: http://lkml.kernel.org/r/1481573103-11329-7-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix typos and add the following to the scripts/spelling.txt:
an one||a one
I dropped the "an" before "one or more" in
drivers/net/ethernet/sfc/mcdi_pcol.h.
Link: http://lkml.kernel.org/r/1481573103-11329-6-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 653d2ffd6405 ("qed*: Fix link indication race") introduced another
race - one of the inner functions called from the link-change flow is
explicitly using the slowpath context dedicated PTT instead of gaining
that PTT from the caller. Since this flow can now be called from
a different context as well, we're in risk of the PTT breaking.
Fixes: 653d2ffd6405 ("qed*: Fix link indication race")
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A PF syncronizes all IOV activity relating to its VFs
by using a single workqueue handling the work.
The workqueue would reach a bitmask of pending VF events
and act upon each in turn.
Problem is that the indication of a VF message [which sets
the 'vf event' bit for that VF] arrives and is set in
the slowpath attention context, which isn't syncronized with
the processing of the events.
When multiple VFs are present, it's possible that PF would
lose the indication of one of the VF's pending evens, leading
that VF to later timeout.
Instead of adding locks/barriers, simply move from a bitmask
into a per-VF indication inside that VF entry in the PF database.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cited commit makes a great job of finding optimal shift/multiplier
values assuming a 10 seconds wrap around, but forgot to change the
overflow_period computation.
It overflows in cyclecounter_cyc2ns(), and the final result is 804 ms,
which is silly.
Lets simply use 5 seconds, no need to recompute this, given how it is
supposed to work.
Later, we will use a timer instead of a work queue, since the new RX
allocation schem will no longer need mlx4_en_recover_from_oom() and the
service_task firing every 250 ms.
Fixes: 31c128b66e ("net/mlx4_en: Choose time-stamping shift value according to HW frequency")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Cc: Eugenia Emantayev <eugenia@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit fix the typo argumnet/argument
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit fix the typo argumnet/argument
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With gcc-4.1.2 and -Os:
drivers/net/ethernet/apm/xgene/xgene_enet_main.c: In function ‘xgene_enet_start_xmit’:
drivers/net/ethernet/apm/xgene/xgene_enet_main.c:297: warning: ‘mss_index’ may be used uninitialized in this function
Using a separate variable to track success may confuse the compiler.
Preinitialize mss_index with -EBUSY and check for negative error values
instead to kill the warning.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The stmmac driver have two methods for registers dumps: via ethtool and
at init (if NETIF_MSG_HW is enabled).
It is better to keep only one method, ethtool, since the other was ugly.
This patch convert all dump_regs() function from "printing regs" to
"fill the reg_space used by ethtool".
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=4Owc
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.11-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- add ASPM L1 substate support
- enable PCIe Extended Tags when supported
- configure PCIe MPS settings on iProc, Versatile, X-Gene, and Xilinx
- increase VPD access timeout
- add ACS quirks for Intel Union Point, Qualcomm QDF2400 and QDF2432
- use new pci_irq_alloc_vectors() in more drivers
- fix MSI affinity memory leak
- remove unused MSI interfaces and update documentation
- remove unused AER .link_reset() callback
- avoid pci_lock / p->pi_lock deadlock seen with perf
- serialize sysfs enable/disable num_vfs operations
- move DesignWare IP from drivers/pci/host/ to drivers/pci/dwc/ and
refactor so we can support both hosts and endpoints
- add DT ECAM-like support for HiSilicon Hip06/Hip07 controllers
- add Rockchip system power management support
- add Thunder-X cn81xx and cn83xx support
- add Exynos 5440 PCIe PHY support
* tag 'pci-v4.11-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (93 commits)
PCI: dwc: Remove dependency of designware on CONFIG_PCI
PCI: dwc: Add CONFIG_PCIE_DW_HOST to enable PCI dwc host
PCI: dwc: Split pcie-designware.c into host and core files
PCI: dwc: designware: Fix style errors in pcie-designware.c
PCI: dwc: designware: Parse "num-lanes" property in dw_pcie_setup_rc()
PCI: dwc: all: Split struct pcie_port into host-only and core structures
PCI: dwc: designware: Get device pointer at the start of dw_pcie_host_init()
PCI: dwc: all: Rename cfg_read/cfg_write to read/write
PCI: dwc: all: Use platform_set_drvdata() to save private data
PCI: dwc: designware: Move register defines to designware header file
PCI: dwc: Use PTR_ERR_OR_ZERO to simplify code
PCI: dra7xx: Group PHY API invocations
PCI: dra7xx: Enable MSI and legacy interrupts simultaneously
PCI: dra7xx: Add support to force RC to work in GEN1 mode
PCI: dra7xx: Simplify probe code with devm_gpiod_get_optional()
PCI: Move DesignWare IP support to new drivers/pci/dwc/ directory
PCI: exynos: Support the PHY generic framework
Documentation: binding: Modify the exynos5440 PCIe binding
phy: phy-exynos-pcie: Add support for Exynos PCIe PHY
Documentation: samsung-phy: Add exynos-pcie-phy binding
...
Pull networking fixes from David Miller:
1) Some 'const'ing in qlogic networking drivers, from Bhumika Goyal.
2) Fix scheduling while atomic in l2tp network namespace exit by
deferring the work to the workqueue. From Ridge Kennedy.
3) Fix use after free in dccp timewait handling, from Andrey Ryabinin.
4) mlx5e CQE compression engine not initialized properly, from Tariq
Toukan.
5) Some UAPI header fixes from Dmitry V. Levin.
6) Don't overwrite module parameter value in mlx4 driver, from Majd
Dibbiny.
7) Fix divide by zero in xt_hashlimit netfilter module, from Alban
Browaeys.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (35 commits)
bpf: Fix bpf_xdp_event_output
net/mlx4_en: Use __skb_fill_page_desc()
net/mlx4_core: Use cq quota in SRIOV when creating completion EQs
net/mlx4_core: Fix VF overwrite of module param which disables DMFS on new probed PFs
net/mlx4: Spoofcheck and zero MAC can't coexist
net/mlx4: Change ENOTSUPP to EOPNOTSUPP
uapi: fix linux/rds.h userspace compilation errors
uapi: fix linux/seg6.h and linux/seg6_iptunnel.h userspace compilation errors
lib: Remove string from parman config selection
forcedeth: Remove return from a void function
bpf: fix spelling mistake: "proccessed" -> "processed"
uapi: fix linux/llc.h userspace compilation error
uapi: fix linux/ip6_tunnel.h userspace compilation errors
net/mlx5e: Fix wrong CQE decompression
net/mlx5e: Update MPWQE stride size when modifying CQE compress state
net/mlx5e: Fix broken CQE compression initialization
net/mlx5e: Do not reduce LRO WQE size when not using build_skb
net/mlx5e: Register/unregister vport representors on interface attach/detach
net/mlx5e: s390 system compilation fix
tcp: account for ts offset only if tsecr not zero
...
Because the Mellanox code required being based on a net-next tree,
I keept it separate from the remainder of the RDMA stack submission
that is based on 4.10-rc3.
This branch contains:
- Various mlx4 and mlx5 fixes and minor changes
- Support for adding a tag match rule to flow specs
- Support for cvlan offload operation for raw ethernet QPs
- A change to the core IB code to recognize raw eth capabilities and
enumerate them (touches non-Mellanox code)
- Implicit On-Demand Paging memory registration support
-----BEGIN PGP SIGNATURE-----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=rspQ
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull Mellanox rdma updates from Doug Ledford:
"Mellanox specific updates for 4.11 merge window
Because the Mellanox code required being based on a net-next tree, I
keept it separate from the remainder of the RDMA stack submission that
is based on 4.10-rc3.
This branch contains:
- Various mlx4 and mlx5 fixes and minor changes
- Support for adding a tag match rule to flow specs
- Support for cvlan offload operation for raw ethernet QPs
- A change to the core IB code to recognize raw eth capabilities and
enumerate them (touches non-Mellanox code)
- Implicit On-Demand Paging memory registration support"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (40 commits)
IB/mlx5: Fix configuration of port capabilities
IB/mlx4: Take source GID by index from HW GID table
IB/mlx5: Fix blue flame buffer size calculation
IB/mlx4: Remove unused variable from function declaration
IB: Query ports via the core instead of direct into the driver
IB: Add protocol for USNIC
IB/mlx4: Support raw packet protocol
IB/mlx5: Support raw packet protocol
IB/core: Add raw packet protocol
IB/mlx5: Add implicit MR support
IB/mlx5: Expose MR cache for mlx5_ib
IB/mlx5: Add null_mkey access
IB/umem: Indicate that process is being terminated
IB/umem: Update on demand page (ODP) support
IB/core: Add implicit MR flag
IB/mlx5: Support creation of a WQ with scatter FCS offload
IB/mlx5: Enable QP creation with cvlan offload
IB/mlx5: Enable WQ creation and modification with cvlan offload
IB/mlx5: Expose vlan offloads capabilities
IB/uverbs: Enable QP creation with cvlan offload
...
Or we might miss the fact that a page was allocated from memory reserves.
Fixes: dceeab0e52 ("mlx4: support __GFP_MEMALLOC for rx")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When creating EQs to handle CQ completion events for the PF
or for VFs, we create enough EQE entries to handle completions
for the max number of CQs that can use that EQ.
When SRIOV is activated, the max number of CQs a VF (or the PF) can
obtain is its CQ quota (determined by the Hypervisor resource tracker).
Therefore, when creating an EQ, the number of EQE entries that the VF
should request for that EQ is the CQ quota value (and not the total
number of CQs available in the FW).
Under SRIOV, the PF, also must use its CQ quota, because
the resource tracker also controls how many CQs the PF can obtain.
Using the FW total CQs instead of the CQ quota when creating EQs resulted
wasting MTT entries, due to allocating more EQEs than were needed.
Fixes: 5a0d0a6161 ("mlx4: Structures and init/teardown for VF resource quotas")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Reported-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the VF driver, module parameter mlx4_log_num_mgm_entry_size was
mistakenly overwritten -- and in a manner which overrode the
device-managed flow steering option encoded in the parameter.
log_num_mgm_entry_size is a global module parameter which
affects all ConnectX-3 PFs installed on that host.
If a VF changes log_num_mgm_entry_size, this will affect all PFs
which are probed subsequent to the change (by disabling DMFS for
those PFs).
Fixes: 3c439b5586 ("mlx4_core: Allow choosing flow steering mode")
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Reviewed-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spoofcheck can't be enabled if VF MAC is zero.
Vice versa, can't zero MAC if spoofcheck is on.
Fixes: 8f7ba3ca12 ('net/mlx4: Add set VF mac address support')
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As ENOTSUPP is specific to NFS, change the return error value to
EOPNOTSUPP in various places in the mlx4 driver.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Suggested-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a void function, it is not necessary to append a return statement in it.
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In cqe compression with striding RQ, the decompression of the CQE field
wqe_counter was done with a wrong wraparound value.
This caused handling cqes with a wrong pointer to wqe (rx descriptor)
and creating SKBs with wrong data, pointing to wrong (and already consumed)
strides/pages.
The meaning of the CQE field wqe_counter in striding RQ holds the
stride index instead of the WQE index. Hence, when decompressing
a CQE, wqe_counter should have wrapped-around the number of strides
in a single multi-packet WQE.
We dropped this wrap-around mask at all in CQE decompression of striding
RQ. It is not needed as in such cases the CQE compression session would
break because of different value of wqe_id field, starting a new
compression session.
Tested:
ethtool -K ethxx lro off/on
ethtool --set-priv-flags ethxx rx_cqe_compress on
super_netperf 16 {ipv4,ipv6} -t TCP_STREAM -m 50 -D
verified no csum errors and no page refcount issues.
Fixes: 7219ab34f1 ("net/mlx5e: CQE compression")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reported-by: Tom Herbert <tom@herbertland.com>
Cc: kernel-team@fb.com
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the admin enables/disables cqe compression, updating
mpwqe stride size is required:
CQE compress ON ==> stride size = 256B
CQE compress OFF ==> stride size = 64B
This is already done on driver load via mlx5e_set_rq_type_params, all we
need is just to call it on arbitrary admin changes of cqe compression
state via priv flags or when changing timestamping state
(as it is mutually exclusive with cqe compression).
This bug introduces no functional damage, it only makes cqe compression
occur less often, since in ConnectX4-LX CQE compression is performed
only on packets smaller than stride size.
Tested:
ethtool --set-priv-flags ethxx rx_cqe_compress on
pktgen with 64 < pkt size < 256 and netperf TCP_STREAM (IPv4/IPv6)
verify `ethtool -S ethxx | grep compress` are advancing more often
(rapidly)
Fixes: 7219ab34f1 ("net/mlx5e: CQE compression")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Cc: kernel-team@fb.com
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of RQ type parameters are derived from CQE compression state flag,
CQE compression flag was initialized only after RQ type parameters
setup. This leads to load RQ with stride size smaller than what we
want for when CQE compression is on.
This bug introduces no functional damage, it only makes CQE compression
occur less often, since in ConnectX4-LX CQE compression is performed
only on packets smaller than stride size.
Fix this by marking default status of CQE compression in PFLAG prior to
calling mlx5e_set_rq_priv_params(), as it inits some fields based on it.
Tested:
load driver on systems where rx CQE compress will be on (MH)
pktgen with 64 < pkt size < 256 and netperf TCP_STREAM (IPv4/IPv6)
verify `ethtool -S ethxx | grep compress` are advancing more often
(rapidly)
Fixes: 2fc4bfb725 ("net/mlx5e: Dynamic RQ type infrastructure")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Cc: kernel-team@fb.com
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When rq_type is Striding RQ, no room of SKB_RESERVE is needed
as SKB allocation is not done via build_skb.
Fixes: e4b8550807 ("net/mlx5e: Slightly reduce hardware LRO size")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently vport representors are added only on driver load and removed on
driver unload. Apparently we forgot to handle them when we added the
seamless reset flow feature. This caused to leave the representors
netdevs alive and active with open HW resources on pci shutdown and on
error reset flows.
To overcome this we move their handling to interface attach/detach, so
they would be cleaned up on shutdown and recreated on reset flows.
Fixes: 26e59d8077 ("net/mlx5e: Implement mlx5e interface attach/detach callbacks")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
show_mem() allows to filter out node specific data which is irrelevant
to the allocation request via SHOW_MEM_FILTER_NODES. The filtering is
done in skip_free_areas_node which skips all nodes which are not in the
mems_allowed of the current process. This works most of the time as
expected because the nodemask shouldn't be outside of the allocating
task but there are some exceptions. E.g. memory hotplug might want to
request allocations from outside of the allowed nodes (see
new_node_page).
Get rid of this hardcoded behavior and push the allocation mask down the
show_mem path and use it instead of cpuset_current_mems_allowed. NULL
nodemask is interpreted as cpuset_current_mems_allowed.
[akpm@linux-foundation.org: coding-style fixes]
Link: http://lkml.kernel.org/r/20170117091543.25850-5-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Acked-by: Mel Gorman <mgorman@suse.de>
Cc: Hillf Danton <hillf.zj@alibaba-inc.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Declare bin_attribute structures as const as they are only passed as an
arguments to the functions device_remove_bin_file and
device_create_bin_file. These function arguments are of type const, so
bin_attribute structures having this property can be made const too.
Done using Coccinelle:
@r1 disable optional_qualifier @
identifier i;
position p;
@@
static struct bin_attribute i@p = {...};
@ok1@
identifier r1.i;
position p,p1;
@@
(
device_remove_bin_file(...,&i@p)
|
device_create_bin_file(..., &i@p1)
)
@bad@
position p!={r1.p,ok1.p,ok1.p1};
identifier r1.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct bin_attribute i;
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Declare bin_attribute structures as const as they are only passed as an
arguments to the functions device_remove_bin_file and
device_create_bin_file. These function arguments are of type const, so
bin_attribute structures having this property can be made const too.
Done using Coccinelle:
@r1 disable optional_qualifier @
identifier i;
position p;
@@
static struct bin_attribute i@p = {...};
@ok1@
identifier r1.i;
position p,p1;
@@
(
device_remove_bin_file(...,&i@p)
|
device_create_bin_file(..., &i@p1)
)
@bad@
position p!={r1.p,ok1.p,ok1.p1};
identifier r1.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct bin_attribute i;
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds glue-code that allows the EMAC driver to interface
with the existing dt-supported PHYs in drivers/net/phy.
Because currently, the emac driver maintains a small library of
supported phys for in a private phy.c file located in the drivers
directory.
The support is limited to mostly single ethernet transceiver like the:
CIS8201, BCM5248, ET1011C, Marvell 88E1111 and 88E1112, AR8035.
However, routers like the Netgear WNDR4700 and Cisco Meraki MX60(W)
have a 5-port switch (AR8327N) attached to the EMAC. The switch chip
is supported by the qca8k mdio driver, which uses the generic phy
library. Another reason is that PHYLIB also supports the BCM54610,
which was used for the Western Digital My Book Live.
This will now also make EMAC select PHYLIB.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use eth_hw_addr_random() to set a random MAC address in order to make
sure bp->dev->addr_assign_type will be properly set to NET_ADDR_RANDOM.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvpp2 is going to be extended to support the Marvell Armada 7K/8K
platform, which is ARM64. As a preparation to this work, this commit
enables building the mvpp2 driver on ARM64, by:
- Adjusting the Kconfig dependency
- Fixing the types used in the driver so that they are 32/64-bits
compliant. We use dma_addr_t for DMA addresses, and unsigned long
for virtual addresses.
It is worth mentioning that after this commit, the driver is for now
still only used on 32-bits platforms, and will only work on 32-bits
platforms.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit adapts the mvpp2 RX path to use the build_skb() method. Not
only build_skb() is now the recommended mechanism, but it also
simplifies the addition of support for the PPv2.2 variant.
Indeed, without build_skb(), we have to keep track for each RX
descriptor of the physical address of the packet buffer, and the virtual
address of the SKB. However, in PPv2.2 running on 64 bits platform,
there is not enough space in the descriptor to store the virtual address
of the SKB. So having to take care only of the address of the packet
buffer, and building the SKB upon reception helps in supporting PPv2.2.
The implementation is fairly straightforward:
- mvpp2_skb_alloc() is renamed to mvpp2_buf_alloc() and no longer
allocates a SKB. Instead, it allocates a buffer using the new
mvpp2_frag_alloc() function, with enough space for the data and SKB.
- The initialization of the RX buffers in mvpp2_bm_bufs_add() as well
as the refill of the RX buffers in mvpp2_rx_refill() is adjusted
accordingly.
- Finally, the mvpp2_rx() is modified to use build_skb().
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the MVPP2_PRS_RI_* definitions use the ~(value) syntax, which
doesn't compile nicely on 64-bit. Moreover, those definitions are in
fact unneeded, since they are always used in combination with a bit
mask that ensures only the appropriate bits are modified.
Therefore, such definitions should just be set to 0x0. In addition, as
suggested by Russell King, we change the _MASK definitions to also use
the BIT() macro so that it is clear they are related to the values
defined afterwards.
For example:
#define MVPP2_PRS_RI_L2_CAST_MASK 0x600
#define MVPP2_PRS_RI_L2_UCAST ~(BIT(9) | BIT(10))
#define MVPP2_PRS_RI_L2_MCAST BIT(9)
#define MVPP2_PRS_RI_L2_BCAST BIT(10)
becomes
#define MVPP2_PRS_RI_L2_CAST_MASK (BIT(9) | BIT(10))
#define MVPP2_PRS_RI_L2_UCAST 0x0
#define MVPP2_PRS_RI_L2_MCAST BIT(9)
#define MVPP2_PRS_RI_L2_BCAST BIT(10)
Because the values (MVPP2_PRS_RI_L2_UCAST, MVPP2_PRS_RI_L2_MCAST and
MVPP2_PRS_RI_L2_BCAST) are always applied with
MVPP2_PRS_RI_L2_CAST_MASK, and therefore there is no need for
MVPP2_PRS_RI_L2_UCAST to be defined as ~(BIT(9) | BIT(10)).
It fixes the following warnings when building the driver on a 64-bit
platform (which is not possible as of this commit, but will be enabled
in a follow-up commit):
drivers/net/ethernet/marvell/mvpp2.c: In function ‘mvpp2_prs_mac_promisc_set’:
drivers/net/ethernet/marvell/mvpp2.c:524:33: warning: large integer implicitly truncated to unsigned type [-Woverflow]
#define MVPP2_PRS_RI_L2_UCAST ~(BIT(9) | BIT(10))
^
drivers/net/ethernet/marvell/mvpp2.c:1459:33: note: in expansion of macro ‘MVPP2_PRS_RI_L2_UCAST’
mvpp2_prs_sram_ri_update(&pe, MVPP2_PRS_RI_L2_UCAST,
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvpp2_bm_bufs_add() currently creates a fake cookie by calling
mvpp2_bm_cookie_pool_set(), just to be able to call
mvpp2_pool_refill(). But all what mvpp2_pool_refill() does is extract
the pool ID from the cookie, and call mvpp2_bm_pool_put() with this ID.
Instead of doing this convoluted thing, just call mvpp2_bm_pool_put()
directly, since we have the BM pool ID.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit drops dead code from the mvpp2 driver. The 'in_use' and
'in_use_thresh' fields of 'struct mvpp2_bm_pool' are
incremented/decremented/initialized in various places. But they are only
used in one place:
if (is_recycle &&
(atomic_read(&bm_pool->in_use) < bm_pool->in_use_thresh))
return 0;
However 'is_recycle', passed as argument to mvpp2_rx_refill() is always
false. So in fact, this code is never reached, and the 'is_recycle'
argument is useless. So let's drop this code.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit remove a field of 'struct mvpp2_tx_queue' that is not used
anywhere.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvpp2_txq_bufs_free() function is called upon TX completion to DMA
unmap TX buffers, and free the corresponding SKBs. It gets the
references to the SKB to free and the DMA buffer to unmap from a per-CPU
txq_pcpu data structure.
However, the code currently increments the pointer to the next entry
before doing the DMA unmap and freeing the SKB. It does not cause any
visible problem because for a given SKB the TX completion is guaranteed
to take place on the CPU where the TX was started. However, it is much
more logical to increment the pointer to the next entry once the current
entry has been completely unmapped/released.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
When configuring the MVPP2_ISR_RX_THRESHOLD_REG with the RX coalescing
time threshold, we do not check for the maximum allowed value supported
by the driver, which means we might overflow and use a bogus value. This
commit adds a check for this situation, and if a value higher than what
is supported by the hardware is provided, then we use the maximum value
supported by the hardware.
In order to achieve this in a way that avoids overflow and rounding
errors, we introduce two utility functions mvpp2_usec_to_cycles() and
cycles_to_usec(). Many thanks to Russell King for suggesting this
implementation.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, mvpp2_rx_pkts_coal_set() does the following to avoid setting
a too large value for the RX coalescing by packet number:
val = (pkts & MVPP2_OCCUPIED_THRESH_MASK);
This means that if you set a value that is slightly higher the the
maximum number of packets, you in fact get a very low value. It makes a
lot more sense to simply check if the value is too high, and if it's too
high, limit it to the maximum possible value.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
As noticed by Russell King, the last argument of
mvpp2_rx_{pkts,time}_coal_set() is useless, since the packet/time
coalescing value is already stored in the 'struct mvpp2_rx_queue *'
passed as argument to these functions. So passing the packet/time value
as an additional argument, and setting them again in the mvpp2_rx_queue
structure is useles.
This commit therefore gets rid of this additional argument, assuming the
caller has assigned the appropriate value to rxq->pkts_coal or
rxq->time_coal before calling the respective functions.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
When TX descriptors are filled in, the buffer DMA address is split
between the tx_desc->buf_phys_addr field (high-order bits) and
tx_desc->packet_offset field (5 low-order bits).
However, when we re-calculate the DMA address from the TX descriptor in
mvpp2_txq_inc_put(), we do not take tx_desc->packet_offset into
account. This means that when the DMA address is not aligned on a 32
bytes boundary, we end up calling dma_unmap_single() with a DMA address
that was not the one returned by dma_map_single().
This inconsistency is detected by the kernel when DMA_API_DEBUG is
enabled. We fix this problem by properly calculating the DMA address in
mvpp2_txq_inc_put().
Cc: <stable@vger.kernel.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit adds the ndo_do_ioctl() callback which allows the userspace to
access PHY registers, for example. This will make mii-diag and similar
tools work.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the bnxt_init_one() failure path, bar1 and bar2 are not
being unmapped. This commit fixes this issue. Reorganize the
code so that bnxt_init_one()'s failure path and bnxt_remove_one()
can call the same function to do the PCI cleanup.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If bnxt_hwrm_ring_free() is called during a failure path in bnxt_open(),
it is possible that the completion rings have not been allocated yet.
In that case, the completion doorbell has not been initialized, and
calling bnxt_disable_int() will crash. Fix it by checking that the
completion ring has been initialized before writing to the completion
ring doorbell.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are additional SoC devices that use the same device ID for
bridge and NIC devices. The bnxt driver should reject probe against
all bridge devices since it's meant to be used with only endpoint
devices.
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver changes the link properties via communication with
the management firmware, and re-reads the resulting link status
when it receives an indication that the link has changed.
However, there are certain scenarios where such indications
might be missing, and so driver also re-reads the current link
results without attention in several places. Specifically, it
does so during load and when resetting the link.
This creates a race where driver might reflect incorrect
link status - e.g., when explicit reading of the link status is
switched by attention with the changed configuration.
Correct this flow by a lock syncronizing the handling of the
link indications [both explicit requests and attention].
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flows accessing registers require the flow to hold a PTT entry.
To protect 'major' load/unload flows a main_ptt is pre-allocated
to guarantee such flows wouldn't be blocked by PTT being
unavailable.
Status block initialization currently uses the main_ptt which
is incorrect, as this flow might run concurrently to others
[E.g., loading qedr while toggling qede]. That would have dire
effects as it means registers' access to device breaks and further
read/writes might access incorrect addresses.
Instead, when initializing status blocks acquire/release a PTT
as part of the flow.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver currently utilizes the same loop variable in two
nested loops.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VF learns of the current link state via its bulletin board,
which might reflect either the physical link state or some
user-configured logical state.
Whenever the physical link changes or whnever such a configuration
is explicitly made by user the PF driver would update the bulletin
that the VF reads. But if neither has happened - i.e., PF still
hasn't got a physical link up and no additional configuration was
done the VF wouldn't have a valid link information available.
Simply reflect the physical link state whenever the VF is
initialized. The user could then affect it however he wants.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qed needs to be informed of the removal of the qede interface
prior to its actual removal, as qede has some registered callbacks
that might get called async to the removal flow.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Need to make sure the slowpath workqueue and the qede lock
are ready for the registration of the netdevice, as once
registered there's no guarantee those wouldn't be used.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reserving doorbell BAR space according to the currently active CPUs
may result in a bug if disabled CPUs are later enabled but no
doorbell space was reserved for them.
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If QP is in reset state then there are no resources to free so avoid
freeing any.
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the state is read only after the buffers are relesed.
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CQ resource pool is protected by a spin lock. When a CQ creation
fails it now deallocates under that lock as well.
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fix removes copying of tx biffers.
Now we use ring->buff_fing directly.
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should allocate the number of pages based on the config parameter
AQ_CFG_RX_FRAME_MAX.
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rxd_wb->pkt_len is the total length of the packet.
If we received a large packet (with length > AQ_CFG_RX_FRAME_MAX) then we
will get multiple buffers. We need to fix the length of the last buffer.
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netdev_register should be called when everything is initialized.
Also we should use net_device->reg_state field instead own
"is_ndev_registered" flag to avoid any race.
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should check for a null pointer for aq_nic_ndev_alloc
instead netdev_priv.
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Reviewed-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use NETDEV_TX_OK as the return value for successful transmission.
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Reviewed-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
rtnl_unlock should be called if error occurred.
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Reviewed-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed superfluous initialization of err.
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Reviewed-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove boilerplate code by using macro module_pci_driver.
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Reviewed-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
1)Removed unnecessary comparsion "old_mtu == new_mtu".
This check is not needed. Function aq_ndev_change_mtu wont be called
if mtu has not changed.
2)Removed extra assignment ndev->mtu = new_mtu;
This assignment already done inside __dev_set_mtu().
3)Use core MTU checking for min_mtu.
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
busy_count field and is_busy flag is not needed at all.
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Reviewed-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This assignment is not needed.
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Reviewed-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some application firmware projects may choose to limit the number
of VFs available below what is specified in PCI capability to be
able to reuse the PCIe interface resources. There may also be
projects which use cases don't require SR-IOV support at all and
therefore don't want to spend time implementing/testing it.
Check nfd_vf_cfg_max_vfs firmware symbol to see if application
firmware is reporting how many VFs it supports. This mechanism
is an opt-in, if symbol is not present we will only look at the
PCI capability values.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
nfp_rtsym_read_le() has an out parameter for error codes.
We have to use that instead of returning errors directly.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow dumping "arm.diag" resource with ethtool -w. This resource
should contain a text log of the NSP (control processor) application.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ethtool_drvinfo->fw_version can cantain multiple FW strings.
We already report NFD ABI version there, add NSP ABI version
if available (i.e. on PF) with 'sp:' prefix.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We read the status register on each NSP open, we can store the NSP
ABI version in the state structure so that we don't have to read
it again.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Report card manufacturing information when driver loads. These
identify the version of the board and its subcomponents.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When acquiring NSP communication resource fails user is left with
"probe failed with error -2" PCI code message but no info on what
caused the problem. Some development boards may not have NSP FW
in the flash image. Help users with a more verbouse message.
While at it move the whole NSP init to a separate function to keep
.probe() callback nice and simple.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If 'dma_alloc_coherent()' fails, we should release resources allocated so
far, just as done in all other cases in this function.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
if 'devm_kzalloc()' fails, we should release resources allocated so far,
just as done a few lines below.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since mlx4 NIC are used on PowerPC with 64K pages, we need to adapt
MLX4_EN_ALLOC_PREFER_ORDER definition.
Otherwise, a fragment sitting in an out of order TCP queue can hold
0.5 Mbytes and it is a serious OOM risk.
Fixes: 51151a16a6 ("mlx4: allow order-0 memory allocations in RX path")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2017-02-18
This series contains updates to i40e and i40evf only.
Alan fixes a bug in which the driver is unable to exit overflow
promiscuous mode after having added "too many" mac filters. Ractored
the '%*ph' printk format specifier to instead use the print_hex_dump().
Josh adds enabling multicast magic packet wakeup by adding calls to
the mac_address_write admin q function during power down to update the
PRTPM_SAH/SAL registers with the MC_MAG_EN bit.
Jake remove a duplicate call i40e_update_link_info(), since it does not
need to call it twice. Fixes and issue where we calculating the wrong
switch id on big endian platforms. Avoided sparse warning, by doing a
typecast to ensure the value is of the type expected by
csum_replace_by_diff().
Mitch fixes a memory leak by freeing resources during i40e_remove().
Cleans up some code confusion by adding a proper code comment.
Carolyn fixes a bug introduced with the addition of the per queue ITR
feature support in ethtool. Cleans up a duplicate device id from the
PCI table.
Harshitha fixes a bug which causes the 'Link Detected' field in
ethtool to report the correct link status.
Benjamin Poirier from SuSE applies a fix ec13ee8014 ("virtio_net:
invoke softirqs after __napi_schedule") to i40e driver as well.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
trivial fix to spelling mistake, en_tsu_err_exeption should
be en_tsu_err_exception
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both functions aq_ring_rx_deinit() and aq_ring_tx_clean() are almost
identical aside from an additional check in the latter.
Move that check from the function into its caller and replace
aq_ring_rx_deinit() with aq_ring_rx_deinit().
By doing this also adjust the functions return value from int to void
since it can never fail.
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Tested-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The check in ena_remove() for the pci driver data not being NULL is not
needed, since it is always set in the probe() function. Remove the
superfluous check.
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add constants and callback functions for the dwmac on rk3328 socs.
As can be seen, the base structure is the same, only registers and the
bits in them moved slightly.
Signed-off-by: david.wu <david.wu@rock-chips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1) In the case where rate == priv->pkt_rate_low == priv->pkt_rate_high,
mlx4_en_auto_moderation() does a divide by zero.
2) We want to properly change the moderation parameters if rx_frames
was changed (like in ethtool -C eth0 rx-frames 16)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After sending device capability queries and requests to the vNIC Server,
an interrupt is triggered and the responses are written to the driver's
CRQ response buffer. Since the interrupt can be triggered before all
responses are written and visible to the partition, there is a danger
that the interrupt handler or tasklet can terminate before all responses
are read, resulting in a failure to initialize the device.
To avoid this scenario, when capability commands are sent, we set
a flag that will be checked in the following interrupt tasklet that
will handle the capability responses from the server. Once all
responses have been handled, the flag is disabled; and the tasklet
is allowed to terminate.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two different counters were being used for capabilities
requests and queries. These commands are not called
at the same time so there is no reason a single counter
cannot be used.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a tasklet to process queued commands or messages received from
firmware instead of processing them in the interrupt handler. Note that
this handler does not process network traffic, but communications related
to resource allocation and device settings.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the backbone required for the various HW initalizations
which are necessary for the FCoE driver (qedf) for QLogic FastLinQ
4xxxx line of adapters - FW notification, resource initializations, etc.
Signed-off-by: Arun Easi <arun.easi@cavium.com>
Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following message is logged from time to time when using i40e:
NOHZ: local_softirq_pending 08
i40e may schedule napi from a workqueue. Afterwards, softirqs are not run
in a deterministic time frame. The problem is the same as what was
described in commit ec13ee8014 ("virtio_net: invoke softirqs after
__napi_schedule") and this patch applies the same fix to i40e.
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix, or rather, avoid a sparse warning caused by the fact that
csum_replace_by_diff expects to receive a __wsum value. Since the
calculation appears to work, simply typecast the passed paylen value to
__wsum to avoid the warning.
This seems pretty fishy since __wsum was obviously annotated as
a separate type on purpose, so this throws the entire calculation into
question. Since it currently appears to behave as expected, the typecast
is probably safe.
Change-ID: I4fdc5cddd589abc16098176e8a61127e761488f4
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There exists an intermittent bug which causes the 'Link Detected'
field reported by the 'ethtool <iface>' command to be 'Yes' when
in fact, there is no link. This patch fixes the problem by
enabling temporary link polling when i40e_get_link_status returns
an error. This causes the driver to remember that an admin queue
command failed and polls, until the function returns with a success.
Change-Id: I64c69b008db4017b8729f3fc27b8f65c8fe2eaa0
Signed-off-by: Harshitha Ramamurthy <harshitha.ramamurthy@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This ensures that the pvid which is stored in __le16 format is converted
to the CPU format. This will fix comparison issues on Big Endian
platforms.
Change-ID: I92c80d1315dc2a0f9f095d5a0c48d461beb052ed
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On Big Endian platforms we would incorrectly calculate the wrong switch
id since we did not properly convert the le16 value into CPU format.
Caught by sparse.
Change-ID: I69a2f9fa064a0a91691f7d0e6fcc206adceb8e36
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch refactors the '%*ph' printk format specifier to instead use
the print_hex_dump function, as recommended by the '%*ph' documentation.
This produces better/more standardized output.
Change-ID: Id56700b4e8abc40ff8c04bc8379e7df04cb4d6fd
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes a bug introduced with the addition of the per queue
ITR feature support in ethtool. With that addition, there were
functions added which converted the ITR settings to binary values.
The IS_ENABLED macros that run on those values check whether a bit
is set or not and with the value being binary, the bit check always
returned ITR disabled which prevents any updating of the ITR rate.
This patch fixes the problem by changing the functions to return the
current ITR value instead and renaming it to better reflect
its function. These functions now provide a value which will be
accurately asessed and update the ITR as intended.
Change-ID: I14f1d088d052e27f652aaa3113e186415ddea1fc
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a comment to reduce confusion.
Change-ID: I3d5819c0f3f5174680442ae54398a073d4a61f4f
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the i40evf_remove() calls netdev close, the device doesn't actually
close - it schedules the work for the watchdog to perform. Since we're
stopping the watchdog, this work doesn't get done. However, we're
resetting the part, so we can free resources after the reset request has
gone through. This plugs a memory leak.
Change-ID: Id5335dcaf76ce00d2a4c3d26e9faf711d7f051cf
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This call is made just prior to running i40e_link_event. In
i40e_link_event, we set hw->phy.get_link_info to true just prior to
calling i40e_get_link_status, which conveniently runs
i40e_update_link_info for us. Thus, we are running i40e_update_link_info
twice, which seems like something we don't need to do...
Change-ID: I36467a570f44b7546d218c99e134ff97c2709315
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a call to the mac_address_write admin q function during
power down to update the PRTPM_SAH/SAL registers with the MC_MAG_EN bit
thus enabling multicast magic packet wakeup.
A FW workaround is needed to write the multicast magic wake up enable
bit in the PRTPM_SAH register. The FW expects the mac address write
admin q cmd to be called first with one of the WRITE_TYPE_LAA flags
and then with the multicast relevant flags.
*Note: This solution only works for X722 devices currently. A PFR will
clear the previously mentioned bit by default, but X722 has support for a
WOL_PRESERVE_ON_PFR flag which prevents the bit from being cleared. Once
other devices support this flag, this solution should work as well.
Change-ID: I51bd5b8535bd9051c2676e27c999c1657f786827
Signed-off-by: Joshua Hay <joshua.a.hay@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There exists a bug in which the driver is unable to exit overflow
promiscuous mode after having added "too many" mac filters. It is
expected that after triggering overflow promiscuous, removing the
failed/extra filters should then disable overflow promiscuous mode.
The bug exists because we were intentionally skipping the sync_vsi_filter
path in cases where we were removing failed filters since they shouldn't
have been added to the firmware in the first place, however we still
need to go through the sync_vsi_filter code path to determine whether or
not it is ok to exit overflow promiscuous mode. This patch fixes the
bug by making sure we go through the sync_vsi_filter path in cases of
failed filters.
Change-ID: I634d249ca3e5fa50729553137c295e73e7722143
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
efx_start_all can return without initialising queues as a reset is pending.
This means that when netif_device_attach is called, the kernel can start
sending traffic without having an initialised TX queue to send to.
This patch avoids this by not calling netif_device_attach if there is a
pending reset.
Fixes: e283546c04 ("sfc:On MCDI timeout, issue an FLR (and mark MCDI to fail-fast)")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the hw doesn't think they exist, we should defer to its authority.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On EF10, hardware filter IDs are 13 bits, but in some places we store
32-bit "full filter IDs" in which higher order bits encode the filter
match-priority. This could cause a filter to have a full filter ID of
0xffff, which is also the value EFX_EF10_FILTER_ID_INVALID which we use
in 16-bit "short" filter IDs (without match-priority bits). This would
occur if the hardware filter ID was 0x1fff and the match-priority was 7.
Unfortunately, some code that checks for EFX_EF10_FILTER_ID_INVALID can
be called on full filter IDs, and will WARN_ON if this ever happens.
So, since we have plenty of spare bits in the full filter ID, this patch
shifts the priority bits left one bit when constructing the full filter
IDs, ensuring that the 0x2000 bit of a full filter ID will always be 0
and thus no full filter ID can ever equal EFX_EF10_FILTER_ID_INVALID.
This patch also replaces open-coded full<->short filter ID conversions
with calls to functions, thus keeping the definition of the full filter
ID format in one place.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use PCI_DEVICE_ID_NETRONOME_NFP*, defined in linux/pci_ids.h,
rather than replicating the same values in the NFP driver.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 34a5102c32 ("net: bgmac: allocate struct bgmac just once
& don't copy it") the mac_addr member of struct bgmac is no longer
necessary to pass the MAC address to bgmac_enet_probe(). Instead it can
directly be stored in netdev->dev_addr.
Also use eth_hw_addr_random() instead of eth_random_addr() in case a
random MAC is nedded. This will make sure netdev->addr_assign_type will
be properly set.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use eth_hw_addr_random() to set a random dev_addr and update
addr_assign_type instead of open-coding it.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This should be >= instead of > here. It means that we don't increment
the free count enough so it becomes off by one.
Fixes: 9ad1a37493 ("dpaa_eth: add support for DPAA Ethernet")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvneta_eth_tool_ops is only used internally in mvneta driver, so
make it static.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ale is a property of cpsw, so change dev to cpsw->dev,
aka pdev->dev, to be consistent.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All rx and rx netdev interrupts are handled by respectively
by mlx4_en_rx_irq() and mlx4_en_tx_irq() which simply schedule a NAPI.
But mlx4_eq_int() also fires a tasklet to service all items that were
queued via mlx4_add_cq_to_tasklet(), but this handler was not called
unless user cqe was handled.
This is very confusing, as "mpstat -I SCPU ..." show huge number of
tasklet invocations.
This patch saves this overhead, by carefully firing the tasklet directly
from mlx4_add_cq_to_tasklet(), removing four atomic operations per IRQ.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
10GbE Intel Wired LAN Driver Updates 2017-02-16
This series contains updates to ixgbe only.
Tony updates the driver to advertise 2.5Gb and 5.0Gb if the adapter
supports it.
Stephen Hemminger renames our dcbnl_ops since it is global to
ixgbe_dcbnl_ops to avoid namespace issues.
Mark updates the driver version based on the recent changes.
Alex has the remainder of the changes, starting with consolidating
functions that represent logical steps in the receive process so we can
later update them more easily (and align with igb). Modify the receive
path to only synchronize the length of the frame versus the entire buffer.
Provided performance improvements by adding support for
DMA_ATTR_SKIP_CPU_SYNC and DMA_ATTR_WEAK_ORDERING. Also made additional
performance gains by batching the page count updates instead of doing
them one at a time. Adjusted the receive path to use 3k buffers with
8k backing them in order to support build_skb with jumbo frames. Made
additional driver improvements by using the length of the packet instead
of the DD status to determine if a new descriptor is ready to be
processed, which cuts down on reads. To reduce code duplication, pulled
apart the receive path into separate functions. Added support for
providing a buffer with headroom and tailroom to allow for shared info
for NET_SKB_PAD and NET_IP_ALIGN.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove variable rxq_info and also remove redundant assignment
to it.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make max number of supported tc u32 links equal to max number of filters
supported by hardware.
Signed-off-by: Arjun V <arjun@chelsio.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes it so that we don't need to bother with clearing the
memory out for the descriptor rings. The general idea is to only free
buffers associated with buffers in use which are located between the
next_to_clean and next_to_use or next_to_alloc values. Everything outside
of those regions can be safely ignored since they should have no buffers
associated with them.
The advantage to doing things this way is that is should speed up bring-up
and tear-down of the rings. Specifically we can avoid the 512 or more
cycles required to memset the rings in tear-down. In the bring-up phase we
then clear the memory as a part of initialization. The general idea is
that the clearing in initialization can act as a prefetch of sorts for the
buffer info structures so they are in the local CPU when we go to populate
them. This should help to improve overall time needed to perform a
suspend/resume.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds build_skb support to the Rx path. There are several
advantages to this change.
1. It avoids the memcpy and skb->head allocation for small packets which
improves performance by about 5% in my tests.
2. It avoids the memcpy, skb->head allocation, and eth_get_headlen
for larger packets improving performance by about 10% in my tests.
3. For VXLAN packets it allows the full header to be in skb->data which
improves the performance by as much as 30% in some of my tests.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since there are potential drawbacks to the new Rx allocation approach I
thought it best to add a "chicken bit" so that we can turn the feature off
if in the event that a problem is found.
It also provides a means of validating the legacy Rx path in the event that
we are forced to fall back. At some point in the future when we are
convinced we don't need it anymore we might be able to drop the legacy-rx
flag.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for providing a buffer with headroom and tailroom
to allow for shared info, NET_SKB_PAD, and NET_IP_ALIGN. With this
combined with the DMA changes we can start using build_skb to build frames
around an incoming Rx buffer instead of having to memcpy the headers.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We are going to be expanding the number of Rx paths in the driver. Instead
of duplicating all that code I am pulling it apart into separate functions
so that we don't have so much code duplication.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that we use the length of the packet instead of the
DD status bit to determine if a new descriptor is ready to be processed.
The obvious advantage is that it cuts down on reads as we don't really even
need the DD bit if going from a 0 to a non-zero value on size is enough to
inform us that the packet has been completed.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In order to support build_skb with jumbo frames it will be necessary to use
3K buffers for the Rx path with 8K pages backing them. This is needed on
architectures that implement 4K pages because we can't support 2K buffers
plus padding in a 4K page.
In the case of systems that support page sizes larger than 4K the 3K
attribute will only be applied to FCoE as we can fall back to using just 2K
buffers and adding the padding.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Batch the page count updates instead of doing them one at a time. By doing
this we can improve the overall performance as the atomic increment
operations can be expensive due to the fact that on x86 they are locked
operations which can cause stalls. By doing bulk updates we can
consolidate the stall which should help to improve the overall receive
performance.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for DMA_ATTR_SKIP_CPU_SYNC and
DMA_ATTR_WEAK_ORDERING. By enabling both of these for the Rx path we are
able to see performance improvements on architectures that implement either
one due to the fact that page mapping and unmapping only has to sync what
is actually being used instead of the entire buffer. In addition by
enabling the weak ordering attribute enables a performance improvement for
architectures that can associate a memory ordering with a DMA buffer such
as Sparc.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On some platforms, syncing a buffer for DMA is expensive. Rather than
sync the whole 2K receive buffer, only synchronise the length of the
frame, which will typically be the MTU, or a much smaller TCP ACK.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch consolidates the code for the ixgbe driver so that it is more
inline with what is already in igb. The general idea is to just
consolidate functions that represent logical steps in the Rx process so we
can later update them more easily.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Update the driver version to reflect the new devices that it
supports.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since dcbnl_ops is global, it should be prefixed by ixgbe_
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Though not advertised through ethtool, if the link partner advertises a
2.5Gb or 5Gb connection, and the adapter supports it, allow the speed to be
used.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Error reports received from firmware were not being converted from
big endian values, leading to bogus error codes reported on little
endian systems.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a vNIC client driver requests a faulty device setting, the
server returns an acceptable value for the client to request.
This 64 bit value was incorrectly being swapped as a 32 bit value,
resulting in loss of data. This patch corrects that by using
the 64 bit swap function.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current behaviour of "mirred redirect" action (forward) offload is a bit
odd. For matched packets the action forwards them to the desired
destination, but it also lets the packet duplicates to go the original
way down (bridge, router, etc). That is more like "mirred mirror".
Fix this by using PBS type which behaves exactly like "mirred redirect".
Note that PBS does not support loopback mode.
Fixes: 4cda7d8d70 ("mlxsw: core: Introduce flexible actions support")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is easier to follow the logic by removing the not operator
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As suggested by Joe Perches, replacing the "if phydev" logic permit to
reduce indentation in the for loop.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 10/100 case have too many ifcase.
This patch split it for removing an if.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch mutualise a bit by running stmmac_hw_fix_mac_speed() after
the switch in case of valid speed.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of invalid speed given, stmmac_adjust_link() still record it as
current speed.
This patch modify the default case to set speed as SPEED_UNKNOWN if not
10/100/1000.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is better to use DUPLEX_UNKNOWN instead of just "-1".
Using 0 for an invalid speed is bad since 0 is a valid value for speed.
So this patch replace 0 by SPEED_UNKNOWN.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The stmmac_adjust_link() function is called too rarely for having
likely() macros being useful.
Just remove likely annotation in it.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch remove some useless parenthesis.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pci_enable_msix has been long deprecated, but this driver adds a new
instance. Convert it to pci_alloc_irq_vectors so that no new instance
of the deprecated function reaches mainline.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the driver support for,
- Registering the ptp clock functionality with the OS.
- Timestamping the Rx/Tx PTP packets.
- Ethtool callbacks related to PTP.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds the required qed interfaces for configuring/reading
the PTP clock on the adapter.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Count buffer group drops or truncates as rx drops rather than
rx errors in netdev stats.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: Arjun V <arjun@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The xilinx_emaclite uses __raw_writel and __raw_readl for register
accesses. Those functions do not imply any kind of memory barriers and
they may be reordered.
The driver does not seem to take that into account, though, and the
driver does not satisfy the ordering requirements of the hardware.
For clear examples, see xemaclite_mdio_write() and xemaclite_mdio_read()
which try to set MDIO address before initiating the transaction.
I'm seeing system freezes with the driver with GCC 5.4 and current
Linux kernels on Zynq-7000 SoC immediately when trying to use the
interface.
In commit 123c1407af ("net: emaclite: Do not use microblaze and ppc
IO functions") the driver was switched from non-generic
in_be32/out_be32 (memory barriers, big endian) to
__raw_readl/__raw_writel (no memory barriers, native endian), so
apparently the device follows system endianness and the driver was
originally written with the assumption of memory barriers.
Rather than try to hunt for each case of missing barrier, just switch
the driver to use iowrite32/ioread32/iowrite32be/ioread32be depending
on endianness instead.
Tested on little-endian Zynq-7000 ARM SoC FPGA.
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Fixes: 123c1407af ("net: emaclite: Do not use microblaze and ppc IO
functions")
Signed-off-by: David S. Miller <davem@davemloft.net>
xilinx_emaclite looks at the received data to try to determine the
Ethernet packet length but does not properly clamp it if
proto_type == ETH_P_IP or 1500 < proto_type <= 1518, causing a buffer
overflow and a panic via skb_panic() as the length exceeds the allocated
skb size.
Fix those cases.
Also add an additional unconditional check with WARN_ON() at the end.
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Fixes: bb81b2ddfa ("net: add Xilinx emac lite device driver")
Signed-off-by: David S. Miller <davem@davemloft.net>
Using a reader-writer lock in fast path is silly, when we can
instead use RCU or a seqlock.
For mlx4 hwstamp clock, a seqlock is the way to go, removing
two atomic operations and false sharing.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The usage count function is based on ndev_running flag that is
updated before calling ndo_open/close, but if ndo is called in
another place, as with suspend/resume, the counter is not changed,
that breaks sus/resume. For common resource no difference which
device is using it, does matter only device count. So, replace
usage count function on var and inc and dec it in ndo_open/close.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
pch_gbe_get_stats() just returns dev->stats so we can leave it out
altogether and let dev_get_stats() do the job.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
hip04_get_stats() just returns dev->stats so we can leave it
out altogether and let dev_get_stats() do the job.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the current driver, the MTU is set to the maximum value
capable for the backing device. This decision turned out to
be a mistake as it led to confusion among users. The expected
initial MTU value used for other IBM vNIC capable operating
systems is 1500, with the maximum value (9000) reserved for
when Jumbo frames are enabled. This patch sets the MTU to
the default value for a net device.
It also corrects a discrepancy between MTU values received from
firmware, which includes the ethernet header length, and net
device MTU values.
Finally, it removes redundant min/max MTU assignments after device
initialization.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a copy-paste error, which hides breaking of resume
for CPSW driver: there was replaced netdev_priv() to ndev_to_cpsw(ndev)
in suspend, but left it unchanged in resume.
Fixes: 606f399395
(ti: cpsw: move platform data and slaves info to cpsw_common)
Reported-by: Alexey Starikovskiy <AStarikovskiy@topcon.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even though the port autoselection is enabled by default on AM79C970A,
BNC/AUI port does not work because the link is always reported to be
down. The link state reported by the chip belongs only to the TP port
but the driver uses it regardless of the port used. The chip can't
detect BNC/AUI link state.
Disable port autoselection and use TP port by default to keep current
behavior (link detection works on TP port, BNC/AUI port does not work).
Implement ethtool autoneg, port and duplex configuration to allow
using the BNC/AUI port.
Report the TP link state only if the TP port is selected. When the
port autoselection is enabled or AUI port is selected, report the link
as always up.
Move pcnet32_suspend() and pcnet32_clr_suspend() functions to avoid
forward declarations.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the code to clear SUSPEND flag to a separate function to simplify
code.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Point back the unregister IPv6 mc table to the bc table.
It is done since IPv6 mcast snooping is not supported for Spectrum yet.
Reported-by: Jiri Pirko <jiri@mellanox.com>
Fixes: 71c365bdc4 ("mlxsw: spectrum: Separate bc and mc floods")
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Tested-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ldmvsw driver is specifically for supporting the ldom virtual
networking by running in the primary ldom and using the LDC to connect
the remaining ldoms to the outside world via a bridge. With TSO and GSO
supported while connected the bridge, things tend to misbehave as seen
in our case by delayed packets, enough to begin triggering retransmits
and affecting overall throughput. By turning off advertised support for
TSO and GSO we restore stable traffic flow through the bridge.
Orabug: 23293104
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New version and simplify the print code.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RCU read lock is grabbed first thing in sunvnet_start_xmit_common()
so it always needs to be released. This removes the conditional release
in the dropped packet error path and removes a couple of superfluous
calls in the middle of the code.
Reported-by: Bijan Mottahedeh <bijan.mottahedeh@oracle.com>
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The use of gotos for handling the incoming events made this code
harder to read and support than it should be. This patch straightens
out and clears up the logic.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to allow the underlying LDC and outstanding memory operations
to potentially catch up with the driver's Tx requests, add a memory
barrier before checking again for available tx descriptors.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There have been several changes since the first version of this code, so
we bump the version number. While we're at it, we can simplify the
version printing a bit and drop a couple lines of code.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vio_dring_state *dr variable is unused in maybe_tx_wakeup().
As the comments indicate, we call maybe_tx_wakeup() whenever we
get a STOPPED LDC message on the port. If the queue is stopped,
we want to wake it up so that we will send another START message
at the next TX and trigger the consumer to drain the dring.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the sunvnet_common code was split out for use by both sunvnet
and the newer ldmvsw, it was made into a static kernel library, which
limits the usefulness of sunvnet and ldmvsw as loadables, since most
of the real work is being done in the shared code. Also, this is
simply dead code in kernels that aren't running the LDoms.
This patch makes the sunvnet_common into a dynamically loadable
module and makes sunvnet and ldmvsw dependent on sunvnet_common.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we fail to probe interrupts with our minimum mode, return that error.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add min_interrupt_mode specification per NIC type.
It is a bit confusing because of "highest interrupt mode is less capable".
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix hardware setup of multicast address hash:
- Never clear the hardware hash (to avoid packet loss)
- Construct the hash register values in software and then write once
to hardware
Signed-off-by: Rui Sousa <rui.sousa@nxp.com>
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When called by HW offloading drivers, the TC action (e.g
net/sched/act_mirred.c) code uses this_cpu logic, e.g
_bstats_cpu_update(this_cpu_ptr(a->cpu_bstats), bytes, packets)
per the kernel documention, preemption should be disabled, add that.
Before the fix, when running with CONFIG_PREEMPT set, we get a
BUG: using smp_processor_id() in preemptible [00000000] code: tc/3793
asserion from the TC action (mirred) stats_update callback.
Fixes: aad7e08d39 ('net/mlx5e: Hardware offloaded flower filter statistics support')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flow rules with same match criteria and value should be mapped to
the same flow table entry regardless the flow tag identifier.
Flow tag is part of flow table entry context and not of the
destination, therefore we should return error when we try to add
destination to flow table entry with different flow tag.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
We had intended to say "sizeof(u32)" but the "u" is missing.
Fortunately, sizeof(32) is also 4, so the original code still works.
Fixes: c4e7beea21 ("net: qcom/emac: add ethtool support for reading hardware registers")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to use an intermediate variable to handle an error code
in this case.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
'of_node_put(fpi->phy_node)' should also be called if we branch to
'out_deregister_fixed_link' error handling path.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2017-02-11
This series contains updates to i40e and i40evf only.
Jake makes a minor change to prevent a minor bit of work, if it is not
necessary. In the case where we do not have a client, there is no need
to check the client params, so move the check till after we have ensured
we have a client. Correct a code comment which incorrectly implied
that raw_packet buffers were freed in i40e_clean_tx_ring(), so fixed
the code comment to better explain where memory is freed. Reduce the
severity and frequency of the message notifying we cleared the receive
timestamp register, since the logic has a much better detection scheme
that could detect a stalled receive timestamp register. The improved
logic was actually causing the notification message to occur more
frequently and was giving the user a false perception that a timestamp
event was missed for a valid packet, so reduce the severity from
dev_warn to dev_dbg and only fire off the message when 3 or 4 of the
RXTIME registers are stalled and get cleared within the same
watchdog event. Fixed a bug, where we were modifying the mac_filter
outside a lock when handling the addition of broadcast filters. Fix
this by updating i40e_update_filter_state logic so that it knows to
avoid broadcast filters, which ensures that we do not have to remove
the filter separately and can put it back using the normal flow.
Refactored how we add new filters to firmware to avoid a race condition
that can occur due to removing filters from the hash temporarily.
Mitch adds a sleep (without timeout) so that we wait for a reply from
the PF before we continue, since the iWarp client cannot continue until
the operation is completed. Fixed up a function which could never
return an error, to be void and cleaned up the checking of the now
null and void return value.
Scott limits the DMA sync to CPU to the actual length of the incoming
packet, versus the syncing of the entire buffer. Also reduces the
receive buffer struct (by a single pointer) and align the driver to be
more consistent with other Intel drivers with respect to packets that
span buffers.
Sudheer adds a field to track the bus number info and modified log
statements to print bus, device and function information.
Henry adds the ability to store the FEC status bits from the link up
event. Also adds the ethtool support for FEC capabilities and 25G
link types.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Using new link mode indices instead deprecated SUPPORTED_/ADVERTISED_
macro.
Added indication for 2500 and 5000mbit link modes (AQtion adapter already
supports these speeds).
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Acked-by: Hyong-Youb Kim <hykim@myri.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Deepak Khungar <deepak.khungar@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add proper puctuation to make the message more clear.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Print FEC (Forward Error Correction) autoneg and encoding settings during
link up.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If it is a VF or an NPAR function, the firmware call to setup the PHY
will fail. Adding this check will prevent unnecessary firmware calls
to setup the PHY unless calling from the PF. This will also eliminate
many unnecessary warning messages when the call from a VF or NPAR fails.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If skb_flow_dissect_flow_keys() returns with the encapsulation flag
set, pass the information to the firmware to setup the NTUPLE filter
accordingly.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit ae10ae740a ("bnxt_en: Add new hardware RFS mode.") has added
code to allow NTUPLE to be enabled on VFs. So we now remove the
BNXT_VF() check in rfs_capable() to allow NTUPLE on VFs.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With commit d1e7925e6d ("bnxt_en: Centralize logic to reserve rings."),
ring allocation for combined rings has become stricter. A combined
ring must now have an rx-tx ring pair. The pre-set max. for combined
rings should now be min(rx, tx).
Fixes: d1e7925e6d ("bnxt_en: Centralize logic to reserve rings.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the HWRM_NVM_INSTALL_UPDATE command fails with the error code
NVM_INSTALL_UPDATE_CMD_ERR_CODE_FRAG_ERR, retry the command with
a new flag to allow defragmentation. Since we are checking the
response for error code, we also need to take the mutex until
we finish reading the response.
Signed-off-by: Kshitij Soni <kshitij.soni@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new spec has NVRAM defragmentation support which will be used in
the next patch to improve ethtool flash operation.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ethtool support needs to save more PHY information. The
added information includes FEC capabilities and 25G link
types. Without this change it is possible to lose 25G or
FEC settings by using ethtool.
Change-ID: Ie42255b1e901ffbf9583b8c46466a54894114280
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Refactor how we add new filters to firmware to avoid a race condition
that can occur due to removing filters from the hash temporarily.
To understand the race condition, suppose that you have a number of MAC
filters, but have not yet added any VLANs. Now, add two VLANs in rapid
succession. A possible resulting flow would look something like the
following:
(1) lock hash for add VLAN
(2) add the new MAC/VLAN combos for each current MAC filter
(3) unlock hash
(4) lock hash for filter sync
(5) notice that we have a VLAN, so prepare to update all MAC filters
with VLAN=-1 to be VLAN=0.
(6) move NEW and REMOVE filters to temporary list
(7) unlock hash
(8) lock hash for add VLAN
(9) add new MAC/VLAN combos. Notice that no MAC filters are currently in
the hash list, so we don't add any VLANs <--- BUG!
(10) unlock hash
(11) sync the temporary lists to firmware
(12) lock hash for post-sync
(13) move the temporary elements back to the main list
....
Because we take filters out of the main hash into temporary lists, we
introduce a narrow window where it is possible that other callers to the
list will not see some of the filters which were previously added but
have not yet been finalized. This results in sometimes dropping VLAN
additions, and could also result in failing to add a MAC address on the
newly added VLAN.
One obvious way to avoid this race condition would be to lock the entire
firmware process. Unfortunately this does not work because adminq
firmware commands take a mutex which results in a sleep while atomic
BUG(). So, we can't use the simplest approach.
An alternative approach is to simply not remove the filters from the
hash list while adding. Instead, add an i40e_new_mac_filter structure
which we will use to track added filters. This avoids the need to remove
the filter from the hash list. We'll store a pointer to the original
i40e_mac_filter, along with our own copy of the state.
We won't update the state directly, so as to avoid race with other code
that may modify the state while under the lock. We are safe to read
f->macaddr and f->vlan since these only change in two locations. The
first is on filter creation, which must have already occurred. The
second is inside i40e_correct_vlan_filters which was previously run
after creation of this object and can't be run again until after. Thus,
we should be safe to read the MAC address and VLAN while outside the
lock.
We also aren't going to run into a use-after-free issue because the only
place where we free filters is when they are marked FAILED or when we
remove them inside the sync subtask. Since the subtask has its own
critical flag to prevent duplicate runs, we know this won't happen. We
also know that the only location to transition a filter from NEW to
FAILED is inside the subtask also, so we aren't worried about that
either.
Use the wrapper i40e_new_mac_filter for additions, and once we've
finalized the addition to firmware, we will update the filter state
inside a lock, and then free the wrapper structure.
In order to avoid a possible race condition with filter deletion, we
won't update the original filter state unless it is still
I40E_FILTER_NEW when we finish the firmware sync.
This approach is more complex, but avoids race conditions related to
filters being temporarily removed from the list. We do not need the same
behavior for deletion because we always unconditionally removed the
filters from the list regardless of the firmware status.
Change-Id: I14b74bc2301f8e69433fbe77ebca532db20c5317
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix a bug where we modified the mac_filter_hash while outside a lock,
when handling addition of broadcast filters.
Normally, we add filters to firmware by batching the additions into
lists and issuing 1 update for every few filters. Broadcast filters are
handled differently, by instead setting the broadcast promiscuous mode
flags. In order to make sure the 1<->1 mapping of filters in our
addition array lined up with filters in the hlist tmp_add_list, we had
to remove the filter and move it back to the main hash. However, we
didn't do this under lock, which could cause consistency problems for
the list.
Fix this by updating i40e_update_filter_state logic so that it knows to
avoid broadcast filters. This ensures that we don't have to remove the
filter separately, and can put it back using the normal flow.
Change-ID: Id288fade80b3e3a9a54b68cc249188cb95147518
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The intent of this message was to indicate to a user that we might have
missed a timestamp event for a valid packet. The original method of
detecting the missed events relied on waiting until all 4 registers were
filled.
A recent commit d55458c0cd7a5 ("i40e: replace PTP Rx timestamp hang
logic") replaced this logic with much better detection
scheme that could detect a stalled Rx timestamp register even when other
registers were still functional.
The new logic means that a message will be displayed almost as soon as
a timestamp for a dropped frame occurs. This new logic highlights that
the hardware will attempt timestamp for frames which it later decides to
drop. The most prominent example is when a multicast PTP frame is
received on a multicast address that we are not subscribed to.
Because the hardware initiates the Rx timestamp as soon as possible, it
will latch an RXTIME register, but then drop the packet.
This results in users being confused by the message as they are not
expecting to see dropped timestamp messages unless their application
also indicates that timestamps were missing.
Resolve this by reducing the severity and frequency of the displayed
message. We now only print the message if 3 or 4 of the RXTIME registers
are stalled and get cleared within the same watchdog event. This ensures
that the common case does not constantly display the message.
Additionally, since the message is likely not as meaningful to most
users, reduce the message to a dev_dbg instead of a dev_warn.
Users can still get a count of the number of timestamps dropped by
reading the ethtool statistics value, if necessary.
Change-ID: I35494442226a444c418dfb4f91a3070d06c8435c
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Store the FEC status bits from the link up event into the
hw_link_info structure.
Change-ID: I9a7b256f6dfb0dce89c2f503075d0d383526832e
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently i40e_bus_info has PCI device and function info only and log
messages print device number as bus number. Added field to provide bus
number info and modified log statements to print bus, device and
function information.
Change-ID: I811617cee2714cc0d6bade8d369f57040990756f
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The function i40e_client_prepare() can never return an error. So make it
void and quit checking its return value.
Change-ID: I9ff311e2324dde329eb68648efb2c94aaff856db
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The original comment implies that the only location where the raw_packet
buffer will be freed is in i40e_clean_tx_ring() which is incorrect. In
fact this isn't even the normal case. Update the comment explaining
where the memory is freed.
Change-ID: Ie0defc35ed1c3af183f81fdc60b6d783707a5595
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Reorganize the i40e_pull_tail() logic, doing it in i40e_add_rx_frag()
where it's cheaper. The igb driver does this the same way.
Also renames i40e_page_is_reserved() to reflect what it actually
tests.
Change-ID: Icd9cc507aae1fcdc02308b3a09034111b4c24071
Signed-off-by: Scott Peterson <scott.d.peterson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch reduces the size of struct i40e_rx_buffer by one pointer,
and makes the i40e driver a little more consistent with the igb driver
in terms of packets that span buffers.
We do this by moving the skb field from struct i40e_rx_buffer to
struct i40e_ring. We pass the skb we already have (or NULL if we
don't) to i40e_fetch_rx_buffer(), which skips the skb allocation if we
already have one for this packet.
Change-ID: I4ad48a531844494ba0c5d8e1a62209a057f661b0
Signed-off-by: Scott Peterson <scott.d.peterson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On packet RX, we perform a DMA sync for CPU before passing the
packet up. Here we limit that sync to the actual length of the
incoming packet, rather than always syncing the entire buffer.
Change-ID: I626aaf6c37275a8ce9e81efcaa773f327b331487
Signed-off-by: Scott Peterson <scott.d.peterson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The iWarp client cannot continue until this operation has been completed
by the PF driver. Sleep (with timeout) until the reply from the PF
driver has been received.
Change-ID: I5dc41b857bba32d0218b7ce167b5da122dadf349
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We can avoid the minor bit of work by calling check params after we
check for the client instance, since we're about to return early in
cases where we do not have a client.
Change-ID: I56f8ea2ba48d4f571fa331c9ace50819a022fa1c
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If skb_padto failed the skb has been dropped already, so it was
consumed, but it doesn't mean it was sent, thus no need to update
queue tx time, etc. So, return NET_XMIT_DROP as more appropriate.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The failure path in ibmvnic_open() mistakenly makes a second call
to napi_enable instead of calling napi_disable. This can result
in a BUG_ON for any queues that were enabled in the previous call
to napi_enable.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialize condition variables prior to invoking any work that can
mark them complete. This resolves a race in the ibmvnic driver where
the driver faults trying to complete an uninitialized condition
variable.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: a0ee354148 ("sfc: process RX event inner checksum flags")
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add PF driver for NFP4000 and NFP6000.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PF services multiple ports using single PCI device therefore
IRQs can no longer be allocated in the netdev code. Lower
portion of the driver has to allocate the IRQs and hand them
out to ports.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PF driver will support multiple ports per PCI device, add port
number to DebugFS paths.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NFP Service Processor (NSP) is an ARM core inside the chip which
is responsible for management and control functions. Add support
for chip reset, FW load and external module access using the NSP.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for using application FW symbol table to look up
location of information in device memory.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MIP is a vector of information which linker can optionally include
in application firmware. It will be used to retrieve the location
of symbol tables.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NFFW info is a resource which contains information about
the loaded application firmware. Add code which will allow
us to decode it and retrieve MIP location.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hwinfo is a simple key=value store of information which is read
from the flash and populated during chip power on. Add code to
look up information in it.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Resource table is an array placed in a well defined location
in device's memory which describes device resources and contains
locks which have to be acquired to use them.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Command Push Pull is the name of NFP's network on a chip.
PCIe PF can access the interconnect through a number of mappings
controlled via Base Access Registers. BARs allow the PF to issue
pretty much any command or address any memory on the chip.
Add appropriate logic and a handful of helper for simple operations
like reading scalars from memories.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support for the PF driver is about to be added and will share
much of the code. When the VF driver was added we planned to
maintain the PF driver as a separate module but have decided
that for our simple use case just maintaining a single module
is more reasonable. Rename the driver to just "nfp" and update
the Kconfig.
While at it remove latent references to NFP3200.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper for checking at runtime that a value will fit inside
a specified field/mask.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to update jiffies in txq->trans_start twice and only for tx 0,
it's supposed to be done in netdev_start_xmit() and per tx queue.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:30: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:30: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:30: error: type defaults to 'int' in declaration of 'MODULE_AUTHOR'
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:30: error: function declaration isn't a prototype
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:31: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:31: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:31: error: type defaults to 'int' in declaration of 'MODULE_DESCRIPTION'
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:31: error: function declaration isn't a prototype
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:32: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:32: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:32: error: type defaults to 'int' in declaration of 'MODULE_LICENSE'
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:32: error: function declaration isn't a prototype
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:33: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:33: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:33: error: type defaults to 'int' in declaration of 'MODULE_VERSION'
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:33: error: function declaration isn't a prototype
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:36: error: expected ')' before 'int'
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:37: error: expected ')' before string constant
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:325: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:325: error: type defaults to 'int' in declaration of 'MODULE_DEVICE_TABLE'
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:325: warning: parameter names (without types) in function declaration
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:3250: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:3250: error: type defaults to 'int' in declaration of 'module_init'
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:3250: warning: parameter names (without types) in function declaration
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:3251: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:3251: error: type defaults to 'int' in declaration of 'module_exit'
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:3251: warning: parameter names (without types) in function declaration
drivers/net/ethernet/cavium/liquidio/lio_main.c:36: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/cavium/liquidio/lio_main.c:36: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_main.c:36: error: type defaults to 'int' in declaration of 'MODULE_AUTHOR'
drivers/net/ethernet/cavium/liquidio/lio_main.c:36: error: function declaration isn't a prototype
drivers/net/ethernet/cavium/liquidio/lio_main.c:37: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/cavium/liquidio/lio_main.c:37: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_main.c:37: error: type defaults to 'int' in declaration of 'MODULE_DESCRIPTION'
drivers/net/ethernet/cavium/liquidio/lio_main.c:37: error: function declaration isn't a prototype
drivers/net/ethernet/cavium/liquidio/lio_main.c:38: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/cavium/liquidio/lio_main.c:38: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_main.c:38: error: type defaults to 'int' in declaration of 'MODULE_LICENSE'
drivers/net/ethernet/cavium/liquidio/lio_main.c:38: error: function declaration isn't a prototype
drivers/net/ethernet/cavium/liquidio/lio_main.c:39: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/cavium/liquidio/lio_main.c:39: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_main.c:39: error: type defaults to 'int' in declaration of 'MODULE_VERSION'
drivers/net/ethernet/cavium/liquidio/lio_main.c:39: error: function declaration isn't a prototype
drivers/net/ethernet/cavium/liquidio/lio_main.c:40: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/cavium/liquidio/lio_main.c:40: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_main.c:40: error: type defaults to 'int' in declaration of 'MODULE_FIRMWARE'
drivers/net/ethernet/cavium/liquidio/lio_main.c:40: error: function declaration isn't a prototype
drivers/net/ethernet/cavium/liquidio/lio_main.c:41: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/cavium/liquidio/lio_main.c:41: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_main.c:41: error: type defaults to 'int' in declaration of 'MODULE_FIRMWARE'
drivers/net/ethernet/cavium/liquidio/lio_main.c:41: error: function declaration isn't a prototype
drivers/net/ethernet/cavium/liquidio/lio_main.c:42: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/cavium/liquidio/lio_main.c:42: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_main.c:42: error: type defaults to 'int' in declaration of 'MODULE_FIRMWARE'
drivers/net/ethernet/cavium/liquidio/lio_main.c:42: error: function declaration isn't a prototype
drivers/net/ethernet/cavium/liquidio/lio_main.c:43: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/cavium/liquidio/lio_main.c:43: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_main.c:43: error: type defaults to 'int' in declaration of 'MODULE_FIRMWARE'
drivers/net/ethernet/cavium/liquidio/lio_main.c:43: error: function declaration isn't a prototype
drivers/net/ethernet/cavium/liquidio/lio_main.c:46: error: expected ')' before 'int'
drivers/net/ethernet/cavium/liquidio/lio_main.c:48: error: expected ')' before string constant
drivers/net/ethernet/cavium/liquidio/lio_main.c:53: error: expected ')' before 'int'
drivers/net/ethernet/cavium/liquidio/lio_main.c:54: error: expected ')' before string constant
drivers/net/ethernet/cavium/liquidio/lio_main.c:57: error: expected ')' before 'sizeof'
drivers/net/ethernet/cavium/liquidio/lio_main.c:58: error: expected ')' before string constant
drivers/net/ethernet/cavium/liquidio/lio_main.c:498: warning: data definitionhas no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_main.c:498: error: type defaults to 'int' in declaration of 'MODULE_DEVICE_TABLE'
drivers/net/ethernet/cavium/liquidio/lio_main.c:498: warning: parameter names (without types) in function declaration
drivers/net/ethernet/cavium/liquidio/lio_main.c: In function 'octeon_recv_vf_drv_notice':
drivers/net/ethernet/cavium/liquidio/lio_main.c:4393: error: implicit declaration of function 'try_module_get'
drivers/net/ethernet/cavium/liquidio/lio_main.c:4400: error: implicit declaration of function 'module_put'
drivers/net/ethernet/cavium/liquidio/lio_main.c: At top level:
drivers/net/ethernet/cavium/liquidio/lio_main.c:4670: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_main.c:4670: error: type defaults to 'int' in declaration of 'module_init'
drivers/net/ethernet/cavium/liquidio/lio_main.c:4670: warning: parameter names (without types) in function declaration
drivers/net/ethernet/cavium/liquidio/lio_main.c:4671: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_main.c:4671: error: type defaults to 'int' in declaration of 'module_exit'
drivers/net/ethernet/cavium/liquidio/lio_main.c:4671: warning: parameter names (without types) in function declaration
Add linux/module.h to both these files.
drivers/net/ethernet/cavium/liquidio/octeon_console.c:40:31: error: expected ')' before 'int'
drivers/net/ethernet/cavium/liquidio/octeon_console.c:42:4: error: expected ')' before string constant
Add linux/moduleparam.h to this file.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/marvell/mvneta.c:2694:26: error: storage size of 'status' isn't known
drivers/net/ethernet/marvell/mvneta.c:2695:26: error: storage size of 'changed' isn't known
drivers/net/ethernet/marvell/mvneta.c:2695:9: error: variable 'changed' has initializer but incomplete type
drivers/net/ethernet/marvell/mvneta.c:2709:2: error: implicit declaration of function 'fixed_phy_update_state' [-Werror=implicit-function-declaration]
Add linux/phy_fixed.h to mvneta.c
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/freescale/fman/fman_memac.c:519:21: error: dereferencing pointer to incomplete type 'struct fixed_phy_status'
Add linux/phy_fixed.h to fman_memac.c
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/broadcom/bgmac.c:1015:17: error: dereferencing pointer to incomplete type 'struct mii_bus'
drivers/net/ethernet/broadcom/bgmac.c:1185:2: error: implicit declaration of function 'phy_start' [-Werror=implicit-function-declaration]
drivers/net/ethernet/broadcom/bgmac.c:1198:2: error: implicit declaration of function 'phy_stop' [-Werror=implicit-function-declaration]
drivers/net/ethernet/broadcom/bgmac.c:1239:9: error: implicit declaration of function 'phy_mii_ioctl' [-Werror=implicit-function-declaration]
drivers/net/ethernet/broadcom/bgmac.c:1389:28: error: 'phy_ethtool_get_link_ksettings' undeclared here (not in a function)
drivers/net/ethernet/broadcom/bgmac.c:1390:28: error: 'phy_ethtool_set_link_ksettings' undeclared here (not in a function)
drivers/net/ethernet/broadcom/bgmac.c:1403:13: error: dereferencing pointer to incomplete type 'struct phy_device'
drivers/net/ethernet/broadcom/bgmac.c:1417:3: error: implicit declaration of function 'phy_print_status' [-Werror=implicit-function-declaration]
drivers/net/ethernet/broadcom/bgmac.c:1424:26: error: storage size of 'fphy_status' isn't known
drivers/net/ethernet/broadcom/bgmac.c:1424:9: error: variable 'fphy_status' has initializer but incomplete type
drivers/net/ethernet/broadcom/bgmac.c:1425:11: warning: excess elements in struct initializer
drivers/net/ethernet/broadcom/bgmac.c:1425:3: error: unknown field 'link' specified in initializer
drivers/net/ethernet/broadcom/bgmac.c:1426:12: note: in expansion of macro 'SPEED_1000'
drivers/net/ethernet/broadcom/bgmac.c:1426:3: error: unknown field 'speed' specified in initializer
drivers/net/ethernet/broadcom/bgmac.c:1427:13: note: in expansion of macro 'DUPLEX_FULL'
drivers/net/ethernet/broadcom/bgmac.c:1427:3: error: unknown field 'duplex' specified in initializer
drivers/net/ethernet/broadcom/bgmac.c:1432:12: error: implicit declaration of function 'fixed_phy_register' [-Werror=implicit-function-declaration]
drivers/net/ethernet/broadcom/bgmac.c:1432:31: error: 'PHY_POLL' undeclared (first use in this function)
drivers/net/ethernet/broadcom/bgmac.c:1438:8: error: implicit declaration of function 'phy_connect_direct' [-Werror=implicit-function-declaration]
drivers/net/ethernet/broadcom/bgmac.c:1439:6: error: 'PHY_INTERFACE_MODE_MII' undeclared (first use in this function)
drivers/net/ethernet/broadcom/bgmac.c:1521:2: error: implicit declaration of function 'phy_disconnect' [-Werror=implicit-function-declaration]
drivers/net/ethernet/broadcom/bgmac.c:1541:15: error: expected declaration specifiers or '...' before string constant
Add linux/phy.h to bgmac.c
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/cadence/macb.h:862:33: sparse: expected ; at end of declaration
drivers/net/ethernet/cadence/macb.h:862:33: sparse: Expected } at end of struct-union-enum-specifier
drivers/net/ethernet/cadence/macb.h:862:33: sparse: got phy_interface
drivers/net/ethernet/cadence/macb.h:877:1: sparse: Expected ; at the end of type declaration
drivers/net/ethernet/cadence/macb.h:877:1: sparse: got }
In file included from drivers/net/ethernet/cadence/macb_pci.c:29:0:
drivers/net/ethernet/cadence/macb.h:862:2: error: unknown type name 'phy_interface_t'
phy_interface_t phy_interface;
^~~~~~~~~~~~~~~
Add linux/phy.h to macb.h
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HW does not understand ETH_P_ALL. So treat this special case differently
and translate to 0/0 key/mask. That will allow HW to match all ethertypes.
Fixes: 7aa0f5aa90 ("mlxsw: spectrum: Implement TC flower offload")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the device being used to DMA map skb->data.
Erroneous device assignment causes the crash when SMMU is enabled.
This happens during TX since buffer gets DMA mapped with device
correspondign to net_device and gets unmapped using the device
related to DSAF.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Reviewed-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a function to update mc_disabled from switchdev attr
SWITCHDEV_ATTR_ID_BRIDGE_MC_DISABLED
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function mlxsw_sp_port_orig_get returns the vport from the physical
port if needed, based on the original device.
This patch addresses the case where the original device is a bridge.
If it is vlan unaware bridge, it returns the matching vport. If it is vlan
aware bridge, there is no matching vport, and it returns the original port.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The decision whether to flood a multicast packet to a port dependent
on three flags: mc_disabled, mc_router_port, mc_flood.
If mc_disabled is on, the port will be flooded according to mc_flood,
otherwise, according to mc_router_port. To accomplish that, add those
flags into the mlxsw_sp_port struct and update the mc flood table
accordingly.
Update mc_router_port by switchdev attribute
SWITCHDEV_ATTR_ID_PORT_MC_ROUTER_PORT.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Break the bm (broadcast-multicast) into two tables, one for broadcast
(and link local multicast that behaves like bc) and one for unknown
multicasts.
Add a bool into mlxsw_sp_port named mc_flood that reflect the value this
port should have in the mc flood table (currently, always 1);
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A user that wants many bridges will use 1.Q bridge which are scalable.
One can have as many 1.Q bridges as vfids.
This patch sets their number to 1k, which is a reasonably large number.
This change is done here because the next patches will add a new flood
table, and without it, it will increase the overall size of the flood
tables dramatically.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, there is a per port flood update function only for the UC
table. Make the function more generic by changing the table type to be
an input.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the flood set function can't operate on only one table, but
sets both uc_flood and mb_flood together.
This patch creates a function that sets the flood state per table.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upon the reception of an ENTRY_REPLACE notification, resolve the FIB
node corresponding to the prefix and length and insert the new route
before the first matching entry.
Since the notification also signals the deletion of the replaced route,
delete it from the driver's cache.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a new route is appended, it's placed after existing routes sharing
the same parameters (prefix, length, table ID, TOS and priority).
While the device supports only one route with the same prefix and length
in a single table, it's important to correctly place the appended route
in the driver's cache, as when a route is deleted the next one is
programmed into the device.
Following the reception of an ENTRY_APPEND notification, resolve the
FIB node corresponding to the prefix and length and correctly place the
new entry in its entry list.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the device, routes are indexed in a routing table based on the prefix
and its length. This is in contrast to the kernel's FIB where several
FIB aliases can exist with these parameters being identical. In such
cases, the routes will be sorted by table ID (LOCAL first, then MAIN),
TOS and finally priority (metric).
During lookup, these routes will be evaluated in order. In case the
packet's TOS field is non-zero and a FIB alias with a matching TOS is
found, then it's selected. Otherwise, the lookup defaults to the route
with TOS 0 (if it exists). However, if the requested scope is narrower
than the one found, then the lookup continues.
To best reflect the kernel's datapath we should take the above into
account. Given a prefix and its length, the reflected route will always
be the first one in the FIB alias list. However, if the route has a
non-zero TOS then its action will be converted to trap instead of
forward, since we currently don't support TOS-based routing. If this
turns out to be a real issue, we can add support for that using
policy-based switching.
The route's scope can be effectively ignored as any packet being routed
by the device would've been looked-up using the widest scope (UNIVERSE).
To achieve that we need to do two changes. Firstly, we need to create
another struct (FIB node) that will hold the list of FIB entries sharing
the same prefix and length. This struct will be hashed using these two
parameters.
Secondly, we need to change the route reflection to match the above
logic, so that the first FIB entry in the list will be programmed into
the device while the rest will remain in the driver's cache in case of
subsequent changes.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the host info config to be the first admin command that is executed.
This change require the driver to remove the 'feature check'
from host info configuration flow.
The check is removed since the supported features bitmask field
is retrieved only after calling ENA_ADMIN_DEVICE_ATTRIBUTES admin command.
If set host info is not supported an error will be returned by the device.
Signed-off-by: Netanel Belgazal <netanel@annapurnalabs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The timeouts were too agressive and sometimes cause false alarms.
Signed-off-by: Netanel Belgazal <netanel@annapurnalabs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Completion descriptors are accessed from the driver and from the device.
To avoid reading the old value, use READ_ONCE macro.
Signed-off-by: Netanel Belgazal <netanel@annapurnalabs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not unamsk interrupts if we are in busy poll mode.
Signed-off-by: Netanel Belgazal <netanel@annapurnalabs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the ena driver detects that the device is not behave as expected,
it tries to reset the device.
The reset flow calls ena_down, which will frees all the resources
the driver allocates and then it will reset the device.
This flow can cause memory corruption if the device is still writes
to the driver's memory space.
To overcome this potential race, move the reset before the device
resources are freed.
Signed-off-by: Netanel Belgazal <netanel@annapurnalabs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ndo_get_stat64() can be called from atomic context, but the current
implementation sends an admin command to retrieve the statistics from
the device. This admin command can sleep.
This patch re-factors the implementation of ena_get_stats64() to use
the {rx,tx}bytes/count from the driver's inner counters, and to obtain
the rx drop counter from the asynchronous keep alive (heart bit)
event.
Signed-off-by: Netanel Belgazal <netanel@annapurnalabs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ENA default hash configures IPv4_frag hash twice instead of
configure non-IP packets.
The bug caused IPv4 fragmented packets to be calculated based on
L2 source and destination address instead of L3 source and destination.
IPv4 packets can reach to the wrong Rx queue.
Signed-off-by: Netanel Belgazal <netanel@annapurnalabs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ena_flow_data_to_flow_hash and ena_flow_hash_to_flow_type
treat the ena_flow_hash_to_flow_type enum as power of two values.
Change the values of ena_admin_flow_hash_fields to be power of two values.
This bug effect the ethtool set/get rxnfc.
ethtool will report wrong values hash fields for get and will
configure wrong hash fields in set.
Signed-off-by: Netanel Belgazal <netanel@annapurnalabs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ENA driver tries to open a queue per vCPU.
To determine how many vCPUs the instance have it uses num_possible_cpus()
while it should have use num_online_cpus() instead.
Signed-off-by: Netanel Belgazal <netanel@annapurnalabs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove NETIF_F_NTUPLE from netdev->features.
The ENA device driver does not support ntuple filtering.
Signed-off-by: Netanel Belgazal <netanel@annapurnalabs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define ndo_features_check. Hw supports offload only for ipv4 inner and
ipv4 outer pkt.
Code refactor for setting inner tcp pseudo csum.
Signed-off-by: Govindarajulu Varadarajan <gvaradar@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Defines enic_udp_tunnel_add/del for configuring vxlan tunnel offload.
enic supports offload of only one ipv4/udp port.
There are two modes that fw supports for vxlan offload.
mode 0: fcoe bit is set for encapsulated packet. fcoe_fc_crc_ok is set
if checksum of csum is ok. This bit is or of ip_csum_ok and
tcp_udp_csum_ok
mode 2: BIT(0) in rss_hash is set if it is encapsulated packet.
BIT(1) is set if outer_ip_csum_ok/
BIT(2) is set if outer_tcp_csum_ok
tcp_udp_csum_ok/ipv4_csum_ok is set if inner csum is OK.
Signed-off-by: Govindarajulu Varadarajan <gvaradar@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds devcmds needed for vxlan offload. Implement 3 new devcmd
overlay_offload_ctrl: enable/disable offload
overlay_offload_cfg: update offload udp port number
get_supported_feature_ver: get hw supported offload version. Each
version has different bitmap for csum_ok/encap
Signed-off-by: Govindarajulu Varadarajan <gvaradar@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the set_ringparam method, which allows the user to specify
the size of the TX and RX descriptor rings. The values are constrained
to the limits of the hardware.
Since the driver does not use separate queues for mini or jumbo frames,
attempts to set those values are rejected.
If the interface is already running when the setting is changed, then
the interface is reset.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the get_regs_len and get_regs ethtool methods. The driver
returns the values of selected hardware registers.
The make the register offsets known to emac_ethtool, the the register
offset macros are all combined into one header file. They were
inexplicably and arbitrarily split between two files.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement ndo_udp_tunnel_{add,del} to update the NIC's list of VXLAN and
GENEVE UDP ports. Also reset the port list to empty on driver load and
on driver unload, with appropriate flag set on the unload case.
These port numbers are used for RX inner checksum offload, and in future
will also be used for TX inner checksum offload and encapsulated TSO.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function wasn't being called in this particular case when the MC
reboots. This caused resource reallocations to not be handled properly
and often ended up disabling the interface.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is mainly to prepare for a future overlay networking patch that
could cause an MC reset at probe time if the UDP tunnel port list is
set immediately upon driver load.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the csum_level for encapsulated packets where the encapsulation
type, l3 class and l4 class are sets that need it.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for RX checksum offload of encapsulated packets. This
essentially just means paying attention to the inner checksum flags
in the RX event, and if *either* checksum flag indicates a fail then
don't tell the kernel that checksum offload was successful.
Also, count these checksum errors and export the counts to ethtool -S.
Test the most common "good" case of RX events with a single bitmask
instead of a series of ifs. Move the more specific error checking
in to a separate function for clarity, and don't use unlikely() there
since we know at least one of the bits is bad.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For T6 adapters use T6 specific macro to set the force bit.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch does not change any functionality but avoids that sparse
complains about endianness.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes the case where there is no phydev attached
to a LMAC in DT due to non-existance of a PHY driver or due
to usage of non-stanadard PHY which doesn't support autoneg.
Changes dependeds on firmware to send correct info w.r.t
PHY and autoneg capability.
This patch also covers a case where a 10G/40G interface is used
as a 1G with convertors with Cortina PHY in between.
Signed-off-by: Thanneeru Srinivasulu <tsrinivasulu@cavium.com>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kernel resolves the nexthops for a given route using
FIB_LOOKUP_IGNORE_LINKSTATE which means a notification can be sent for a
route with one of its nexthops being LINKDOWN.
In case IGNORE_ROUTES_WITH_LINKDOWN is set for the nexthop netdev, then
we shouldn't reflect the nexthop to the device's table.
Once the nexthop netdev's carrier goes up we'll be notified using NH_ADD
and reflect it to the device.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the last IP address is removed from a netdev, its RIF is deleted.
However, if user didn't first remove neighbours and nexthops using this
interface, then they would still be present in the device's tables.
Therefore, whenever a RIF is deleted, make sure all the neighbours and
nexthops (adjacency entries) using it are removed from the relevant
tables as well.
The action associated with any route using this RIF would be refreshed,
most likely to trap. If the kernel decides to remove the route (f.e.,
because all the nexthops are now DEAD), then an event would be sent,
causing the route to be removed from the device.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a packet hits a multipath route in the device's routing table, a
hash is computed over its headers, which is then used to select the
appropriate nexthop from the device's adjacency table.
There are situations in which the kernel removes a nexthop from a
multipath route (e.g., no carrier) and the device should do the same.
Upon the reception of NH_{ADD,DEL} events, add or remove a nexthop from
the device's adjacency table and refresh all the routes using the
nexthop group. If all the nexthops of a multipath route are invalid,
then any packet hitting the route would be trapped to the CPU for
forwarding.
If all the nexthops are DEAD, then the kernel would remove the route
entirely. On the other hand, if all the nexthops are merely LINKDOWN,
then the kernel would keep the route and forward any incoming packet
using a different route.
While the last case might sound like a problem, it's expected that a
routing daemon running in user space would remove such a route from the
FIB as it's dumped with the DEAD flag set.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device can have one of three actions associated with a route:
1) Remote - packets continue to the adjacency table
2) Local - packets continue to the neighbour table
3) Trap - packets continue to the CPU
The first two actions can also trap packets to the CPU, but they do so
using a different trap ID, which has a lower traffic class and less
allotted bandwidth.
We currently use the third action for both RTN_{LOCAL,BROADCAST} routes
and RTN_UNICAST routes not pointing to the switch ports.
However, packets that merely need to be forwarded by the switch are
likely not control packets and can be therefore scheduled towards the
CPU using a lower traffic class.
Achieve the above by assigning the third action only to local and
broadcast routes and have any other route use either of the first two
actions, based on whether the route is gatewayed or not.
This will also allow us to refresh routes using the local action and
have them trap packets when their RIF is no longer valid following a
NH_DEL event.
One side effect of this patch is that we no longer give special
treatment to multipath routes using both switch and non-switch ports
towards their nexthops. If at least one of the nexthops can be resolved,
then the device will forward the packets instead of trapping them.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous patch introduced a generic function to determine whether a
route should be offloaded or not. Make use of it here.
In the future we're going to add more conditions to this test (e.g.,
whether TOS is non-zero), so it makes sense to centralize it instead of
open coding it in a few places.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently set the RTNH_F_OFFLOAD flag for all routes using remote
action, but this isn't always correct. If none of the nexthops
associated with a gatewayed route can be offloaded into the device, then
any packet hitting it would be trapped to the CPU and forwarded by the
kernel.
Solve this by pushing the setting of the offload flag to after the route
was programmed into the device, thereby allowing us to take all the
parameters into account.
This change will also help us further in the patchset, when we refresh
routes following the reception of NH_{ADD,DEL} events.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The nexthop init and de-init functions both have symmetric parts
concerned with the reflection of the neighbour entry into the device's
adjacency table, in case it's used by a gatewayed route.
These sections of code also need to be called when a nexthop is marked
as valid / invalid following NH_{ADD,DEL} events. Break these out into
appropriate functions, so that they could be invoked following the
reception of above events.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the previous changes, the FIB info is embedded in every nexthop
group struct, which in turn is embedded in every FIB entry struct.
We can therefore safely remove the FIB info from the entry struct. This
has the added advantage of making the router-related structs more
generic and suitable for use with IPv6 offloads.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until now, the only FIB entries that were associated with a nexthop
group were routes to remote networks where all the nexthop devices had a
valid router interface (RIF). This is in contrast to the FIB code,
where all the routes are associated with a FIB info. The same design
choice needs to be applied to the driver's cache.
Based on the NH_{ADD,DEL} events which will be added later in the
patchset, we need to be able to change the action (forward / trap)
associated with all the routes using the nexthop group. However, if we
can't link between the nexthop and the routes using it, then the above
is impossible.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The next patch is going to generalize the way in which we store routes.
Instead of attaching a nexthop group only to gatewayed routes, one will
be attached to each route, in a similar way to the way the FIB code
stores its routes.
The above means that any function operating on a nexthop group cannot
assume the group represents only gatewayed nexthops. One such function
is the one that refreshes a nexthop group and updates the adjacency
table following nexthop changes.
For a nexthop group that doesn't represent any gateways this function
would essentially be a NOP, but it would be useful if it did update the
action associated with any route using it. This will allow us to later
consolidate code paths when a nexthop changes following NH_{ADD,DEL}
events.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently use the scope of the FIB info to distinguish between a
direct unicast route and a gatewayed one. However, the kernel is
perfectly happy to configure a route with scope UNIVERSE to a directly
connected network.
Instead, we can rely on the first nexthop's scope to check if the route
is gatewayed or not.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Later in the patchset we'll add the NH_{ADD,DEL} events which will let
us know when a nexthop is considered to be dead. Based on these events
we need to be able to add or remove the nexthop from the device's
tables.
Therefore, store the private nexthop structs in a hash table and use the
kernel's fib_nh struct as the key, so that we'll be able to easily find
them when the events are received.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when we're notified about a new RTN_UNICAST route we perform
a lookup on the nexthop group list looking for a group with a matching
configuration to that found in the FIB info. This is quite inefficient.
Instead, we can simply rely on the kernel to consolidate several FIB
configurations into the same FIB info and use the FIB info as the key
for our private nexthop group struct.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we invalidate a nexthop we should also invalidate its neighbour
entry pointer as it might be destroyed later on. This makes the nexthop
de-init function symmetric with its init and also ensures nobody will
try to access the neighbour entry.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No rollback is needed since the chain is in consistent state and
mlxsw_afa_block_destroy() will take care of putting it away. So remove
the one we have now which is wrong. Also move the set of 'finished' flag
to the beginning of the function, because the block is certainly unusable
for future action addition no matter if the function succeeds or not.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 4cda7d8d70 ("mlxsw: core: Introduce flexible actions support")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
checkpatch complains about two unsigned without type after.
Since the value return is u32, it is simpler to replace it by u32 instead
of "unsigned int"
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The u64 x variable in sysfs_display_ring is unused.
This patch remove it.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit cf32deec16 ("stmmac: add tx_skbuff_dma to save descriptors used by PTP"),
the struct dma_desc *p in stmmac_tx_clean was not used at all.
This patch remove this dead code.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a PHY is found, printing which one was found (and which type/model) is
a good information to know.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool stat counter rx_crc from stmmac is mis-named, the name
seems to speak about the number of RX CRC done, but in fact it is about
errors.
This patch rename it to rx_crc_errors, just like the same ifconfig
counter.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch rewrite two test against NULL value with correct style.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The message about invalid speed does not state 1000 as a valid speed.
It is much simpler to said that the speed is invalid.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As said by checkpatch ENOSYS means 'invalid syscall nr' and nothing
else.
This patch replace ENOSYS by the more appropriate value EINVAL.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dwmac_dma_reset function use an open coded of readl_poll_timeout().
Replace the open coded handling with the proper function.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The stmmac_mdio_busy_wait() function do the same job than
readl_poll_timeout().
So is is better to replace it.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
