This patch adds the interconnects property for the gpu node and the
opp-peak-kBps property to the opps of the gpu opp table. This should
help enable DDR bandwidth scaling dynamically and proportionally to the
GPU frequency.
Signed-off-by: Sharat Masetty <smasetty@codeaurora.org>
Signed-off-by: Akhil P Oommen <akhilpo@codeaurora.org>
Link: https://lore.kernel.org/r/1594992579-20662-5-git-send-email-akhilpo@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add "qcom,replicator-loses-context" property to the replicator
in Always-on domain in SC7180 SoC to enable coresight replicator
driver to handle this variation of replicator designs.
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Link: https://lore.kernel.org/r/5072d94849cfaee46748d26ac997212fb2d783c2.1591708204.git.saiprakash.ranjan@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add "qcom,skip-power-up" property to skip powering up ETM
on SC7180 SoC to workaround a hardware errata where CPU
watchdog counter is stopped when ETM power up bit is set
(i.e., when TRCPDCR.PU = 1).
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Link: https://lore.kernel.org/r/8c5ff297d8c89d9d451352f189baf26c8938842a.1591708204.git.saiprakash.ranjan@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Adding maximum speed property for DWC3 USB node which can be used
for setting interconnect bandwidth.
Signed-off-by: Sandeep Maheswaram <sanm@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/1595317489-18432-3-git-send-email-sanm@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add "arm,coresight-loses-context-with-cpu" property to coresight
ETM nodes to avoid failure of trace session because of losing
context on entering deep idle states.
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Link: https://lore.kernel.org/r/20200721071343.2898-1-saiprakash.ranjan@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add the OPP tables for DSI and MDP based on the perf state/clk
requirements, and add the power-domains property to specify the
scalable power domain.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/1594292674-15632-5-git-send-email-rnayak@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add the OPP tables for DSI and MDP based on the perf state/clk
requirements, and add the power-domains property to specify the
scalable power domain.
Tested-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/1594292674-15632-4-git-send-email-rnayak@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
All the platforms using SC7180 SoC are expected to have the wlan firmware
memory statically mapped by the Trusted Firmware. Hence move back the
qcom,msa-fixed-perm property to the SoC dtsi.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Fixes: 7d48456608 ("arm64: dts: qcom: sc7180: Add missing properties for Wifi node")
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200716191746.23196-1-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
A3U/A5U both use a Bosch BMC150 accelerometer/magnetometer combo.
The chip provides two separate I2C devices for the accelerometer
and magnetometer that are already supported by the bmc150-accel
and bmc150-magn driver.
The only difference between A3U/A5U is the way the sensor is
mounted on the mainboard - set the mount-matrix in the
device-specific device tree part to handle that difference.
Co-developed-by: Michael Srba <michael.srba@seznam.cz>
Signed-off-by: Michael Srba <michael.srba@seznam.cz>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200622151751.408995-5-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Commit c240f29e75 ("arm64: dts: set the default i2c pin drive strength to 16mA")
changed the default drive-strength for I2C pins in msm8916-pins.dtsi
to the maximum possible (16 mA).
While this makes sense for apq8016-sbc (DB410c) where you can connect
an arbitrary amount of I2C devices with level shifters etc, there is
no need to use a higher drive strength for other MSM8916 devices.
The minimum drive strength (2 mA) seems to be totally sufficient
to have everything work there.
With the short pinctrl nodes introduced earlier we can easily override
the drive-strength only for apq8016-sbc now. Use that and change
the default back to 2 mA.
i2c1_default/i2c5_default are already using 2 mA because they were
added separately later and are not used in apq8016-sbc.
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200622151751.408995-4-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
So far we have been separating pinctrl entries into pinmux/pinconf.
It turns out it is also possible to combine them: The advantage is
that the device tree is overall more concise because the "pins"
to configure just need to be specified once, not separately for
pinmux/pinconf.
Using the simpler form only for new entries would be rather confusing.
This commit makes all MSM8916 device trees use the simplfied form.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200622151751.408995-3-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
It is helpful to be able to see all hardware components in one part
of the device tree, without having to scroll over the large amount
of regulator/pinctrl nodes. Keep those separated at the end of the file
to make navigation a bit easier.
This also makes it consistent with the order used in apq8016-sbc.dtsi.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200622151751.408995-2-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Now that we don't need the intermediate syscon to represent the TCSR
mutexes, update the dts to describe the TCSR mutex directly under /soc.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200622075956.171058-5-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The wlan firmware memory is statically mapped in
the Trusted Firmware, hence the wlan driver does
not need to map/unmap this region dynamically.
Hence add the property to indicate the wlan driver
to not map/unamp the firmware memory region
dynamically.
Also add the chain1 voltage supply for wlan.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Link: https://lore.kernel.org/r/1594615586-17055-1-git-send-email-pillair@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The WiFi supplies that were added recently can't have done anything
useful because they were missing the "-supply" suffix. Booting
without the "-supply" suffix would give these messages:
ath10k_snoc 18800000.wifi: 18800000.wifi supply vdd-0.8-cx-mx not found, using dummy regulator
ath10k_snoc 18800000.wifi: 18800000.wifi supply vdd-1.8-xo not found, using dummy regulator
ath10k_snoc 18800000.wifi: 18800000.wifi supply vdd-1.3-rfa not found, using dummy regulator
ath10k_snoc 18800000.wifi: 18800000.wifi supply vdd-3.3-ch0 not found, using dummy regulator
Let's add the "-supply" suffix.
Tested-by: Rakesh Pillai <pillair@codeaurora.org>
Reviewed-by: Rakesh Pillai <pillair@codeaurora.org>
Fixes: 1e7594a38f ("arm64: dts: qcom: sc7180: Add WCN3990 WLAN module device node")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200625131658.REPOST.1.I32960cd32bb84d6db4127c906d7e371fa29caebf@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add the vendor-specific registers and clock for Qualcomm ICE (Inline
Crypto Engine) to the device tree node for the UFS host controller on
sdm845, so that the ufs-qcom driver will be able to use inline crypto.
Use a separate register range rather than extending the main UFS range
because there's a gap between the two, and the ICE registers are
vendor-specific. (Actually, the hardware claims that the ICE range also
includes the array of standard crypto configuration registers; however,
on this SoC the Linux kernel isn't permitted to access them directly.)
Signed-off-by: Eric Biggers <ebiggers@google.com>
Link: https://lore.kernel.org/r/20200710072013.177481-4-ebiggers@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add the power domain supporting performance state and the corresponding
OPP tables for the sdhc device on sc7180.
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Link: https://lore.kernel.org/r/1593506712-24557-5-git-send-email-rnayak@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add the power domain supporting performance state and the corresponding
OPP tables for the sdhc device on sdm845.
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Link: https://lore.kernel.org/r/1593506712-24557-4-git-send-email-rnayak@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
qup has a requirement to vote on the performance state of the CX domain
in sc7180 devices. Add OPP tables for these and also add power-domains
property for all qup instances for uart and spi.
i2c does not support scaling and uses a fixed clock.
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Link: https://lore.kernel.org/r/1593506712-24557-3-git-send-email-rnayak@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
qup has a requirement to vote on the performance state of the CX domain
in sdm845 devices. Add OPP tables for these and also add power-domains
property for all qup instances for uart and spi.
i2c does not support scaling and uses a fixed clock.
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/1593506712-24557-2-git-send-email-rnayak@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add the power domain supporting performance state and the corresponding
OPP tables for the qspi device on sc7180
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Link: https://lore.kernel.org/r/1593769293-6354-4-git-send-email-rnayak@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add the power domain supporting performance state and the corresponding
OPP tables for the qspi device on sdm845
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Link: https://lore.kernel.org/r/1593769293-6354-3-git-send-email-rnayak@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Having a non-MSA (Modem Self-Authentication) SID bypassed breaks modem
sandboxing i.e if a transaction were to originate from it, the hardware
memory protections units (XPUs) would fail to flag them (any transaction
originating from modem are historically termed as an MSA transaction).
Drop the unused non-MSA modem SID on SC7180 SoCs and cheza so that SMMU
continues to block them.
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Fixes: bec71ba243 ("arm64: dts: qcom: sc7180: Update Q6V5 MSS node")
Fixes: 68aee4af5f ("arm64: dts: qcom: sdm845-cheza: Add iommus property")
Cc: stable@vger.kernel.org
Reported-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200630081938.8131-1-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add a simple-mfd representing IMEM on SDM845 and define the PIL
relocation info region, so that post mortem tools will be able to locate
the loaded remoteprocs.
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200622191942.255460-6-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add a simple-mfd representing IMEM on QCS404 and define the PIL
relocation info region, so that post mortem tools will be able to locate
the loaded remoteprocs.
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200622191942.255460-5-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add OPP tables required to scale DDR/L3 per freq-domain on SC7180 SoCs.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200626190808.8716-1-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add properties required for the bootloader to select
the correct bootloader blob. They have been removed from
the SoC device tree as they should be set on a per-device
basis.
Signed-off-by: Konrad Dybcio <konradybcio@gmail.com>
Link: https://lore.kernel.org/r/20200623224813.297077-11-konradybcio@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add PSCI node to enable multi-processor startup.
Note that not every 8994 device firmware supports PSCI,
and even if, then it can only start the cores and not
shut them down.
Signed-off-by: Konrad Dybcio <konradybcio@gmail.com>
Link: https://lore.kernel.org/r/20200623224813.297077-10-konradybcio@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add support for I2C and SPI buses to enable peripherals
such as touchscreens or sensors. Also add DMA nodes,
configuration and BLSP2 UART2 interface.
Signed-off-by: Konrad Dybcio <konradybcio@gmail.com>
Link: https://lore.kernel.org/r/20200623224813.297077-8-konradybcio@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Following changes have been made:
- remove name, compatible and msm-id
- wrap clocks in clocks{}
- order nodes by name and by address
- clock_gcc -> gcc
- msmgpio -> tlmm
- qcom,smem -> smem
- remove unit-address from smem
- retire msm8994-pins.dtsi
- add some of the missing pins
- make comments C-style
Signed-off-by: Konrad Dybcio <konradybcio@gmail.com>
Link: https://lore.kernel.org/r/20200623224813.297077-2-konradybcio@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add remoteproc nodes for the audio, compute and sensor cores, define
glink for each one and enable them on the MTP with appropriate firmware
defined.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20200622222747.717306-6-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
SMP2P is used for interrupting and being interrupted about remoteproc
state changes related to the audio, compute and sensor subsystems.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20200622222747.717306-5-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
PM8150 ldo11 on the MTP is wired to VDD_SSC_CX and controlled in levels,
rather than as a regulator. As such it's available from the rpmhpd as
the SM8250_LCX power domain.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Fixes: ec13d5c23a ("arm64: dts: qcom: sm8250-mtp: Add pm8150, pm8150l and pm8009")
Link: https://lore.kernel.org/r/20200622222747.717306-2-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add device tree support for the Sony Xperia 10 and 10
Plus smartphones. They are all based on the Sony Ganges
platform (sdm630/636) and share a lot of common code.
The differences are really minor, so a Ganges-common DTSI
has been created to reduce clutter.
10 - Kirin
10 Plus - Mermaid
This platform is based on SoMC Nile, but there are some
major differences when it comes to pin configuration and
panel setup (among others).
The boards currently support:
* Screen console
* SDHCI
* I2C
* pstore log dump
* GPIO keys
* PSCI idle states
Signed-off-by: Martin Botka <martin.botka1@gmail.com>
Signed-off-by: Konrad Dybcio <konradybcio@gmail.com>
Tested-by: Martin Botka <martin.botka1@gmail.com>
Link: https://lore.kernel.org/r/20200622192558.152828-7-konradybcio@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add device tree support for the Sony Xperia XA2, XA2 Plus and
XA2 Ultra smartphones. They are all based on the Sony Nile
platform (sdm630) and share a lot of common code. The
differences are really minor, so a Nile-common DTSI
has been created to reduce clutter.
XA2 - Pioneer
XA2 Plus - Voyager
XA2 Ultra - Discovery
The boards currently support:
* Screen console
* SDHCI
* I2C
* pstore log dump
* GPIO keys
* PSCI idle states
Signed-off-by: Konrad Dybcio <konradybcio@gmail.com>
Tested-by: Łukasz Patron <priv.luk@gmail.com>
Link: https://lore.kernel.org/r/20200622192558.152828-6-konradybcio@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add devicetree files for SDM630 SoC and its pin configuration.
This commit adds basic nodes like cpu, psci and other required
configuration for booting up from eMMC to the serial console.
Signed-off-by: Konrad Dybcio <konradybcio@gmail.com>
Link: https://lore.kernel.org/r/20200622192558.152828-5-konradybcio@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Much like SDM845 each serial engine has 4 pins attached. Add all
possible I2C and SPI nodes for all 20 serial engines.
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20200606131300.3874987-1-dmitry.baryshkov@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
