Problem:
The introduction of separate run queues per CPU has brought with it "nice"
enforcement problems that are best described by a simple example.
For the sake of argument suppose that on a single CPU machine with a
nice==19 hard spinner and a nice==0 hard spinner running that the nice==0
task gets 95% of the CPU and the nice==19 task gets 5% of the CPU. Now
suppose that there is a system with 2 CPUs and 2 nice==19 hard spinners and
2 nice==0 hard spinners running. The user of this system would be entitled
to expect that the nice==0 tasks each get 95% of a CPU and the nice==19
tasks only get 5% each. However, whether this expectation is met is pretty
much down to luck as there are four equally likely distributions of the
tasks to the CPUs that the load balancing code will consider to be balanced
with loads of 2.0 for each CPU. Two of these distributions involve one
nice==0 and one nice==19 task per CPU and in these circumstances the users
expectations will be met. The other two distributions both involve both
nice==0 tasks being on one CPU and both nice==19 being on the other CPU and
each task will get 50% of a CPU and the user's expectations will not be
met.
Solution:
The solution to this problem that is implemented in the attached patch is
to use weighted loads when determining if the system is balanced and, when
an imbalance is detected, to move an amount of weighted load between run
queues (as opposed to a number of tasks) to restore the balance. Once
again, the easiest way to explain why both of these measures are necessary
is to use a simple example. Suppose that (in a slight variation of the
above example) that we have a two CPU system with 4 nice==0 and 4 nice=19
hard spinning tasks running and that the 4 nice==0 tasks are on one CPU and
the 4 nice==19 tasks are on the other CPU. The weighted loads for the two
CPUs would be 4.0 and 0.2 respectively and the load balancing code would
move 2 tasks resulting in one CPU with a load of 2.0 and the other with
load of 2.2. If this was considered to be a big enough imbalance to
justify moving a task and that task was moved using the current
move_tasks() then it would move the highest priority task that it found and
this would result in one CPU with a load of 3.0 and the other with a load
of 1.2 which would result in the movement of a task in the opposite
direction and so on -- infinite loop. If, on the other hand, an amount of
load to be moved is calculated from the imbalance (in this case 0.1) and
move_tasks() skips tasks until it find ones whose contributions to the
weighted load are less than this amount it would move two of the nice==19
tasks resulting in a system with 2 nice==0 and 2 nice=19 on each CPU with
loads of 2.1 for each CPU.
One of the advantages of this mechanism is that on a system where all tasks
have nice==0 the load balancing calculations would be mathematically
identical to the current load balancing code.
Notes:
struct task_struct:
has a new field load_weight which (in a trade off of space for speed)
stores the contribution that this task makes to a CPU's weighted load when
it is runnable.
struct runqueue:
has a new field raw_weighted_load which is the sum of the load_weight
values for the currently runnable tasks on this run queue. This field
always needs to be updated when nr_running is updated so two new inline
functions inc_nr_running() and dec_nr_running() have been created to make
sure that this happens. This also offers a convenient way to optimize away
this part of the smpnice mechanism when CONFIG_SMP is not defined.
int try_to_wake_up():
in this function the value SCHED_LOAD_BALANCE is used to represent the load
contribution of a single task in various calculations in the code that
decides which CPU to put the waking task on. While this would be a valid
on a system where the nice values for the runnable tasks were distributed
evenly around zero it will lead to anomalous load balancing if the
distribution is skewed in either direction. To overcome this problem
SCHED_LOAD_SCALE has been replaced by the load_weight for the relevant task
or by the average load_weight per task for the queue in question (as
appropriate).
int move_tasks():
The modifications to this function were complicated by the fact that
active_load_balance() uses it to move exactly one task without checking
whether an imbalance actually exists. This precluded the simple
overloading of max_nr_move with max_load_move and necessitated the addition
of the latter as an extra argument to the function. The internal
implementation is then modified to move up to max_nr_move tasks and
max_load_move of weighted load. This slightly complicates the code where
move_tasks() is called and if ever active_load_balance() is changed to not
use move_tasks() the implementation of move_tasks() should be simplified
accordingly.
struct sched_group *find_busiest_group():
Similar to try_to_wake_up(), there are places in this function where
SCHED_LOAD_SCALE is used to represent the load contribution of a single
task and the same issues are created. A similar solution is adopted except
that it is now the average per task contribution to a group's load (as
opposed to a run queue) that is required. As this value is not directly
available from the group it is calculated on the fly as the queues in the
groups are visited when determining the busiest group.
A key change to this function is that it is no longer to scale down
*imbalance on exit as move_tasks() uses the load in its scaled form.
void set_user_nice():
has been modified to update the task's load_weight field when it's nice
value and also to ensure that its run queue's raw_weighted_load field is
updated if it was runnable.
From: "Siddha, Suresh B" <suresh.b.siddha@intel.com>
With smpnice, sched groups with highest priority tasks can mask the imbalance
between the other sched groups with in the same domain. This patch fixes some
of the listed down scenarios by not considering the sched groups which are
lightly loaded.
a) on a simple 4-way MP system, if we have one high priority and 4 normal
priority tasks, with smpnice we would like to see the high priority task
scheduled on one cpu, two other cpus getting one normal task each and the
fourth cpu getting the remaining two normal tasks. but with current
smpnice extra normal priority task keeps jumping from one cpu to another
cpu having the normal priority task. This is because of the
busiest_has_loaded_cpus, nr_loaded_cpus logic.. We are not including the
cpu with high priority task in max_load calculations but including that in
total and avg_load calcuations.. leading to max_load < avg_load and load
balance between cpus running normal priority tasks(2 Vs 1) will always show
imbalanace as one normal priority and the extra normal priority task will
keep moving from one cpu to another cpu having normal priority task..
b) 4-way system with HT (8 logical processors). Package-P0 T0 has a
highest priority task, T1 is idle. Package-P1 Both T0 and T1 have 1 normal
priority task each.. P2 and P3 are idle. With this patch, one of the
normal priority tasks on P1 will be moved to P2 or P3..
c) With the current weighted smp nice calculations, it doesn't always make
sense to look at the highest weighted runqueue in the busy group..
Consider a load balance scenario on a DP with HT system, with Package-0
containing one high priority and one low priority, Package-1 containing one
low priority(with other thread being idle).. Package-1 thinks that it need
to take the low priority thread from Package-0. And find_busiest_queue()
returns the cpu thread with highest priority task.. And ultimately(with
help of active load balance) we move high priority task to Package-1. And
same continues with Package-0 now, moving high priority task from package-1
to package-0.. Even without the presence of active load balance, load
balance will fail to balance the above scenario.. Fix find_busiest_queue
to use "imbalance" when it is lightly loaded.
[kernel@kolivas.org: sched: store weighted load on up]
[kernel@kolivas.org: sched: add discrete weighted cpu load function]
[suresh.b.siddha@intel.com: sched: remove dead code]
Signed-off-by: Peter Williams <pwil3058@bigpond.com.au>
Cc: "Siddha, Suresh B" <suresh.b.siddha@intel.com>
Cc: "Chen, Kenneth W" <kenneth.w.chen@intel.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Con Kolivas <kernel@kolivas.org>
Cc: John Hawkes <hawkes@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There is a race between set_cpus_allowed() and move_task_off_dead_cpu().
__migrate_task() doesn't report any err code, so task can be left on its
runqueue if its cpus_allowed mask changed so that dest_cpu is not longer a
possible target. Also, chaning cpus_allowed mask requires rq->lock being
held.
Signed-off-by: Kirill Korotaev <dev@openvz.org>
Acked-By: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Unless we expect to have more than 2G CPUs, there's no reason to have 'i'
as a long long here.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The relationship between INTERACTIVE_SLEEP and the ceiling is not perfect
and not explicit enough. The sleep boost is not supposed to be any larger
than without this code and the comment is not clear enough about what
exactly it does, just the reason it does it. Fix it.
There is a ceiling to the priority beyond which tasks that only ever sleep
for very long periods cannot surpass. Fix it.
Prevent the on-runqueue bonus logic from defeating the idle sleep logic.
Opportunity to micro-optimise.
Signed-off-by: Con Kolivas <kernel@kolivas.org>
Signed-off-by: Mike Galbraith <efault@gmx.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initial report and lock contention fix from Chris Mason:
Recent benchmarks showed some performance regressions between 2.6.16 and
2.6.5. We tracked down one of the regressions to lock contention in
schedule heavy workloads (~70,000 context switches per second)
kernel/sched.c:dependent_sleeper() was responsible for most of the lock
contention, hammering on the run queue locks. The patch below is more of a
discussion point than a suggested fix (although it does reduce lock
contention significantly). The dependent_sleeper code looks very expensive
to me, especially for using a spinlock to bounce control between two
different siblings in the same cpu.
It is further optimized:
* perform dependent_sleeper check after next task is determined
* convert wake_sleeping_dependent to use trylock
* skip smt runqueue check if trylock fails
* optimize double_rq_lock now that smt nice is converted to trylock
* early exit in searching first SD_SHARE_CPUPOWER domain
* speedup fast path of dependent_sleeper
[akpm@osdl.org: cleanup]
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Con Kolivas <kernel@kolivas.org>
Signed-off-by: Nick Piggin <npiggin@suse.de>
Acked-by: Chris Mason <mason@suse.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Replace the temp makefile hacks with proper CONFIG entries, which are also
added to Kconfig.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add current pin settings to gpio_dump() output. This adds the last 'word' to
the syslog lines, which displays the input and output values that the pin is
set to.
pc8736x_gpio.0: io00: 0x0044 TS OD PUE EDGE LO DEBOUNCE io:1/1
The 2 values may differ for a number of reasons:
1- the pin output circuitry is diaabled, (as the above 'TS' indicates)
2- it needs a pullup resistor to drive the attached circuit,
3- the external circuit needs a pullup so the open-drain has something
to pull-down
4- the pin is wired to Vcc or Ground
It might be appropriate to add a WARN for 2,3,4, since they could
damage the chip and/or circuit, esp if misconfig goes unnoticed.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Hmm. Im somewhat ambivalent about this patch, since with it, driver wont
build for vanilla 17 or older.
Its also only 1/2 of your suggestion - when I tried it, I was building against
vanilla 17, and asm/uaccess.h cause compilation failure. Looking back, Im
perplexed as to why linux/io.h didnt cause same failure ?!?
use linux/io.h rather than asm/io.h
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Replace spinlocks guarding gpio config ops with mutexes. This is a me-too
patch, and is justifiable insofar as mutexes have stricter semantics and
better debugging support, so are preferred where they are applicable.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a working gpio_current() to pc8736x_gpio.c (the previous implementation
just threw a dev_warn), and fix gpio_change() to use gpio_current() rather
than the incorrect (and temporary) gpio_get(). Initialize shadow-regs so this
all works.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use of dev_dbg() and friends is considered good practice. dev_dbg() needs a
struct device *devp, but nsc_gpio is only a helper module, so it doesnt
have/need its own. To provide devp to the user-modules (scx200 & pc8736x
_gpio), we add it to the vtable, and set it during init.
Also squeeze nsc_gpio_dump()'s format a little.
[ 199.259879] pc8736x_gpio.0: io09: 0x0044 TS OD PUE EDGE LO DEBOUNCE
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Adds platform-device to (just introduced) driver, and uses it to replace many
printks with dev_dbg() etc. This could trivially be merged into previous
patch, but this way matches better with the corresponding patch that does the
same change to scx200_gpio.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add the brand new pc8736x_gpio driver. This is mostly based upon
scx200_gpio.c, but the platform_dev is treated separately, since its fairly
big too.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Since the meaning of config-bits is the same for scx200 and pc8736x _gpios, we
can share a function to deliver this to user. Since it is called via the
vtable, its also completely replaceable. For now, we keep using printk...
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Now that the read(), write() file-ops are dispatching gpio-ops via the vtable,
they are generic, and can be moved 'verbatim' to the nsc_gpio common-support
module. After the move, various symbols are renamed to update 'scx200_' to
'nsc_', and headers are adjusted accordingly.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add the nsc_gpio common-support module as an empty shell. Next patch starts
the migration of the common gpio support routines.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Now actually call the gpio operations thru the vtable.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Abstract the gpio operations into a new nsc_gpio_ops vtable.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Pull shadow-reg initialization into separate function now, rather than doing
it 2x later (scx200, pc8736x). When we revisit 2nd drvr below, it will be to
reimplement an init function, rather than another refactor.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a new driver command: 'v' which calls gpio_dump() on the pin. The output
goes to the log, like all other INFO messages in the original driver. Giving
the user control over the feedback they 'need' is construed to be a
user-friendly feature, and allows us (later) to dial down many INFO messages
to DEBUG log-level.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Shrink scx200_gpio_dump() to a single printk with ternary ops. The function
is still ifdef'd out, this is corrected in next patch, when it is actually
used.
The patch 'inadvertently' changed loglevel from DEBUG to INFO. This is Good,
because in next patch, its wired to a 'command' which the user can invoke when
they want. When they do so, its because they want INFO to support their
developement effort, and we want to give it to them without compiling a DEBUG
version of the driver.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Per kernel headers, device minor numbers are unsigned ints. Do the same in
this driver.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a platform-device to scx200_gpio, and use its struct device dev member
(ie: devp) in dev_dbg() once.
There are 2 alternatives here (Im soliciting guidance/commentary):
- use isa_device, if/when its added to the kernel.
- alter scx200.c to EXPORT_GPL its private devp so that both scx200_gpio,
and the (to be added) nsc_gpio module can use it. Since the available devp
is in 'grandparent', this seems like too much 'action at a distance'.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Adopt many modern 2.6 coding practices, ala LDD3, chapter 3. Changes are
limited to initialization calls from module init, ie: cdev_init, cdev_add,
*_chrdev_region, mkdev.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
GPIO SUPPORT FOR SCx200 & PC8736x
The patch-set reworks the 2.4 vintage scx200_gpio driver for modern 2.6, and
refactors GPIO support to reuse it in a new driver for the GPIO on PC-8736x
chips. Its handy for the Soekris.com net-4801, which has both chips.
These patches have been seen recently on Kernel-Mentors, and then
Kernel-Newbies ML, where Jesper Juhl kindly reviewed it. His feedback has
been incorporated. Thanks Jesper !
Its also gone to soekris-tech@soekris.com for possible testing by linux folks,
I've gotten 1 promise so far. Theyre mostly BSD folk over there, but we'll
see..
Device-file & Sysfs
The driver preserves the existing device-file interface, including the
write/cmd set, but adds v to 'view' the pin-settings & configs by inducing,
via gpio_dump(), a dev_info() call. Its a fairly crappy way to get status,
but it sticks to the syslog approach, conservatively.
Allowing users to voluntarily trigger logging is good, it gives them a
familiar way to confirm their app's control & use of the pins, and I've thus
reduced the pin-mode-updates from dev_info to dev_dbg.
I've recently bolted on a proto sysfs interface for both new drivers. Im not
including those patches here; they (the patch + doc-pre-patch) are still quite
raw (and unreviewed on KNML), and since they 'invent' a convention for GPIO, a
proper vetting is needed. Since this patchset is much bigger than my previous
ones, Id like to keep things simpler, and address it 1st, before bolting on
more stuff.
The driver-split
The Geode CPU and the PC-87366 Super-IO chip have GPIO units which share a
common pin-architecture (same pin features, with same bits controlling), but
with different addressing mechanics and port organizations.
The vintage driver expresses the pin capabilities with pin-mode commands
[OoPpTt],etc that change the pin configurations, and since the 2 chips share
pin-arch, we can reuse the read(), write() commands, once the implementation
is suitably adjusted.
The patchset adds a vtable: struct nsc_gpio_ops, to abstract the existing gpio
operations, then adjusts fileops.write() code to invoke operations via that
vtable. Driver specific open()s set private_data to the vtable so its
available for use by write().
The vtable gets the gpio_dump() too, since its user-friendly, and (could be
construed as) part of the current device-file interface. To support use of
dev_dbg() in write() & _dump(), the vtable gets a dev ptr too, set by both
scx200 & pc8736x _gpio drivers.
heres how the pins are presented in syslog:
[ 1890.176223] scx200_gpio.0: io00: 0x0044 TS OD PUE EDGE LO DEBOUNCE
[ 1890.287223] scx200_gpio.0: io01: 0x0003 OE PP PUD EDGE LO
nsc_gpio.c: new file is new home of several file-ops methods, which are
modified to get their vtable from filp->private_data, and use it where needed.
scx200_gpio.c: keeps some of its existing gpio routines, but now wires them up
via the vtable (they're invoked by nsc_gpio.c:nsc_gpio_write() thru this
vtable). A driver-spcific open() initializes filp->private_data with the
vtable.
Once the split is clean, and the scx200_gpio driver is working, we copy and
modify the function and variable names, and rework the access-method bodies
for the different addressing scheme.
Heres a working overview of the patchset:
# series file for GPIO
# Spring Cleaning
gpio-scx/patch.preclean # scripts/Lindent fixes, editor-ctrl comments
# API Modernization
gpio-scx/patch.api26 # what I learned from LDD3
gpio-scx/patch.platform-dev-2 # get pdev, support for dev_dbg()
gpio-scx/patch.unsigned-minor # fix to match std practice
# Debuggability
gpio-scx/patch.dump-diet # shrink gpio_dump()
gpio-scx/patch.viewpins # add new 'command' to call dump()
gpio-scx/patch.init-refactor # pull shadow-register init to sub
# Access-Abstraction (add vtable)
gpio-scx/patch.access-vtable # introduce nsg_gpio_ops vtable, w dump
gpio-scx/patch.vtable-calls # add & use the vtable in scx200_gpio
gpio-scx/patch.nscgpio-shell # add empty driver for common-fops
# move code under abstraction
gpio-scx/patch.migrate-fops # move file-ops methods from scx200_gpio
gpio-scx/patch.common-dump # mv scx200.c:scx200_gpio_dump() to nsc_gpio.c
gpio-scx/patch.add-pc8736x-gpio # add new driver, like old, w chip adapt
# gpio-scx/patch.add-DEBUG # enable all dev_dbg()s
# Cleanups
# finish printk -> dev_dbg() etc
gpio-scx/patch.pdev-pc8736x # new drvr needs pdev too,
gpio-scx/patch.devdbg-nscgpio # add device to 'vtable', use in dev_dbg()
# gpio-scx/patch.pin-config-view # another 'c' 'command'
# gpio-scx/quiet-getset # take out excess dbg stuff (pretty quiet
now)
gpio-scx/patch.shadow-current # imitate scx200_gpio's shadow regs in
pc87*
# post KMentors-post patches ..
gpio-scx/patch.mutexes # use mutexes for config-locks
gpio-scx/patch.viewpins-values # extend dump to obsolete separate 'c' cmd
gpio-scx/patch.kconfig # add stuff for kbuild
# TBC
# combine api26 with pdev, which is just one step.
# merge c&v commands to single do-all-fn
# delay viewpins, dump-diet should also un-ifdef it too.
diff.sys-gpio-rollup-1
This patch:
Removed editor format-control comments, and used scripts/Lindent to clean up
whitespace, then deleted the bogus chunks :-(
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make use the of newly defined hotplug version of cpu_notifier functionality
wherever appropriate.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Define new macros register_hotcpu_notifier() and unregister_hotcpu_notifier()
that redefines register_cpu_notifier() and unregister_cpu_notifier() for use
only when HOTPLUG_CPU is defined.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make notifier_calls associated with cpu_notifier as __cpuinit.
__cpuinit makes sure that the function is init time only unless
CONFIG_HOTPLUG_CPU is defined.
[akpm@osdl.org: section fix]
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make notifier_blocks associated with cpu_notifier as __cpuinitdata.
__cpuinitdata makes sure that the data is init time only unless
CONFIG_HOTPLUG_CPU is defined.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
CPUs come online only at init time (unless CONFIG_HOTPLUG_CPU is defined).
So, cpu_notifier functionality need to be available only at init time.
This patch makes register_cpu_notifier() available only at init time, unless
CONFIG_HOTPLUG_CPU is defined.
This patch exports register_cpu_notifier() and unregister_cpu_notifier() only
if CONFIG_HOTPLUG_CPU is defined.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In 2.6.17, there was a problem with cpu_notifiers and XFS. I provided a
band-aid solution to solve that problem. In the process, i undid all the
changes you both were making to ensure that these notifiers were available
only at init time (unless CONFIG_HOTPLUG_CPU is defined).
We deferred the real fix to 2.6.18. Here is a set of patches that fixes the
XFS problem cleanly and makes the cpu notifiers available only at init time
(unless CONFIG_HOTPLUG_CPU is defined).
If CONFIG_HOTPLUG_CPU is defined then cpu notifiers are available at run
time.
This patch reverts the notifier_call changes made in 2.6.17
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We need to serialize access to the global rtc_idr even in this error path.
Signed-off-by: Sonny Rao <sonny@burdell.org>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There are two locking sets involved. One locks the board mappings and the
other is the tty open/close locking. The low level code was clearly
designed to be ported to OS's with spin locks already so pretty much comes
out in the wash
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Corey Minyard <minyard@acm.org>
The kthread used to speed up polling for IPMI was using udelay in its
busy-wait polling loop when the lower-level state machine told it to do a
short delay. This just used CPU and didn't help scheduling, thus causing
bad problems with other tasks. Call schedule() instead.
Signed-off-by: Corey Minyard <minyard@acm.org>
Acked-by: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add operations for the call_rcu_bh() variant of RCU. Also add an
rcu_batches_completed_bh() function, which is needed by rcutorture.
Signed-off-by: Paul E. McKenney <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add an ops vector to rcutorture, and add the ops for Classic RCU. Update
the rcutorture documentation to reflect slight change to the dmesg formats.
Signed-off-by: Paul E. McKenney <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This just catches the RCU torture documentation up with the recent fixes
that test RCU for architectures that turn of the scheduling-clock interrupt
for idle CPUs and the addition of a SUCCESS/FAILURE indication, fixing up
an obsolete comment as well.
Signed-off-by: Paul E. McKenney <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix kernel-doc parameters in kernel/
Warning(/var/linsrc/linux-2617-g9//kernel/auditsc.c:1376): No description found for parameter 'u_abs_timeout'
Warning(/var/linsrc/linux-2617-g9//kernel/auditsc.c:1420): No description found for parameter 'u_msg_prio'
Warning(/var/linsrc/linux-2617-g9//kernel/auditsc.c:1420): No description found for parameter 'u_abs_timeout'
Warning(/var/linsrc/linux-2617-g9//kernel/acct.c:526): No description found for parameter 'pacct'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix TCSBRK comment to prevent confusion or accidental removal.
Signed-off-by: Paul Fulghum <paulkf@microgate.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add missed ufsi->i_dir_start_lookup initialization in ufs_read_inode in
UFS2 case. Also it cleans ufs_read_inode function to prevent such kind of
situation in the future: it move depend on UFS type parts of code into
separate functions and leaves in ufs_read_inode only generic code. It
cleans code and avoids duplication.
Signed-off-by: Evgeniy Dushistov <dushistov@mail.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
generic_file_buffered_write() prefaults in user pages in order to avoid
deadlock on copying from the same page as write goes to.
However, it looks like there is a problem when write is vectored:
fault_in_pages_readable brings in current segment or its part (maxlen).
OTOH, filemap_copy_from_user_iovec is called to copy number of bytes
(bytes) which may exceed current segment, so filemap_copy_from_user_iovec
switches to the next segment which is not brought in yet. Pagefault is
generated. That causes the deadlock if pagefault is for the same page
write goes to: page being written is locked and not uptodate, pagefault
will deadlock trying to lock locked page.
[akpm@osdl.org: somewhat rewritten]
Cc: Neil Brown <neilb@suse.de>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We include config.h on the compiler command line. There's no need for it
to be included again.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
locking init cleanups:
- convert " = SPIN_LOCK_UNLOCKED" to spin_lock_init() or DEFINE_SPINLOCK()
- convert rwlocks in a similar manner
this patch was generated automatically.
Motivation:
- cleanliness
- lockdep needs control of lock initialization, which the open-coded
variants do not give
- it's also useful for -rt and for lock debugging in general
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- add a proper prototype for the following global function:
- buffer_init()
- make the following needlessly global function static:
- end_buffer_async_write()
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add more poison values to include/linux/poison.h. It's not clear to me
whether some others should be added or not, so I haven't added any of
these:
./include/linux/libata.h:#define ATA_TAG_POISON 0xfafbfcfdU
./arch/ppc/8260_io/fcc_enet.c:1918: memset((char *)(&(immap->im_dprambase[(mem_addr+64)])), 0x88, 32);
./drivers/usb/mon/mon_text.c:429: memset(mem, 0xe5, sizeof(struct mon_event_text));
./drivers/char/ftape/lowlevel/ftape-ctl.c:738: memset(ft_buffer[i]->address, 0xAA, FT_BUFF_SIZE);
./drivers/block/sx8.c:/* 0xf is just arbitrary, non-zero noise; this is sorta like poisoning */
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Update two drivers to use poison.h.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Localize poison values into one header file for better documentation and
easier/quicker debugging and so that the same values won't be used for
multiple purposes.
Use these constants in core arch., mm, driver, and fs code.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: Matt Mackall <mpm@selenic.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
