Overwrite hw queue id for non-bufferable management frames if the hw/fw
support always txq (altxq) in order to be in sync with mac txwi code
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is easy to add MU EDCA parameters in the future. This patch
also fixes a wrong cw_min assignment.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Enable MU-MIMO DL/UL and add relative counters in debugfs.
Currently MU modules read WTBL first to notify BA changes to
other cross modules, so adjust mt7915_mcu_sta_ba() accordingly.
Tested-by: Evelyn Tsai <evelyn.tsai@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In MT7915, hardware queue map is flexible. However, certain firmware modules
like MU and U-APSD presume a fixed queue order to adapt some devices that have
DMA scheduler with a strict order, so this patch can help in the long run.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce U-APSD support in mt76 driver for AP interface
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
For consistency with the rest of the code always rely on defined
macros for register access
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
kernel test robot <lkp@intel.com> found the following issue
and Kalle Valo forwarded it to Linux wireless.
drivers/net/wireless/mediatek/mt76/pci.c:8:6:
warning: no previous prototype for 'mt76_pci_disable_aspm'
Fix this by adding the missing include of mt76.h as Kalle
suggested.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
While looking at the ETSI regulatory domain definitions
and a patch, which allows more channels for ath10k, I also
checked the channels allowed for mt76.
ETSI regulations would possibly allow to add channels 32, 68,
96, 144, 169 and 173. IEEE 802.11-2016 defines no operating class
for channels 32, 68 and 96. This leaves us channels 144, 169 and 173,
which are included in this patch.
I tested 169 and 173 with a mt76 based USB dongle (AVM AC 860) and they
worked fine. If I saw that right, these channels are also covered by
register definitions inside the driver.
Channel 144 should also work, but gets disabled by the kernel as of now.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix up typo in Kconfig with indicating MT7663U is an 802.11ac device
Fixes: eb99cc95c3 ("mt76: mt7615: introduce mt7663u support")
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Rely on mt76_for_each_q_rx whenever possible in order to simply the code
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Overwrite hw queue id for non-bufferable management frames if the hw
support always txq (altxq) in order to be in sync with mac txwi code
Fixes: cdad487405 ("mt76: mt7615: add dma and tx queue initialization for MT7622")
Fixes: f40ac0f3d3 ("mt76: mt7615: introduce mt7663e support")
Suggested-by: Felix Fietkau <nbd@nbd.name>
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
mt7622/mt7663 chipsets rely on a fixed reverse queue map order respect
to mac80211 one:
- q(0): IEEE80211_AC_BK
- q(1): IEEE80211_AC_BE
- q(2): IEEE80211_AC_VI
- q(3): IEEE80211_AC_VO
Fixes: cdad487405 ("mt76: mt7615: add dma and tx queue initialization for MT7622")
Fixes: f40ac0f3d3 ("mt76: mt7615: introduce mt7663e support")
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Co-developed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
acs and wmm index are swapped in mt7615_queues_acq respect to the hw
design
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Coverage class callback can potentially run in parallel with other
routines (e.g. mt7615_set_channel) that configures timing registers.
Run coverage class callback holding mt76 mutex
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
First set of patches for v5.9. This comes later than usual as I was
offline for two weeks. The biggest change here is moving Microchip
wilc1000 driver from staging. There was an immutable topic branch with
one commit moving the whole driver and the topic branch was pulled
both to staging-next and wireless-drivers-next. At the moment the only
reported conflict is in MAINTAINERS file, so I'm hoping the move
should go smoothly.
Other notable changes are ath11k getting 6 GHz band support and rtw88
supporting RTL8821CE. And there's also the usual fixes, API changes
and cleanups all over.
Major changes:
wilc1000
* move from drivers/staging to drivers/net/wireless/microchip
ath11k
* add 6G band support
* add spectral scan support
iwlwifi
* make FW reconfiguration quieter by not using warn level
rtw88
* add support for RTL8821CE
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJfFWQeAAoJEG4XJFUm622bVAwH/3r2oR+NS1kNDNGi9nrLAIav
trLgPa2VbgPVgTcwIckfvZFl6BK9zo1KG6u6jYp45C6uNBJNESjarf8aLAXvXdFt
t0yBkb6OCUq+efoOFbxV2im6ER57aN27POsn74xrCeR3fwZgY9QSHRMjQ5x1tjWH
JdVatT6jtu2LuxsTjfS0K5kjeuyE0vE1iCUlsQ5qwcSLODGa9u7ydheoNcLOHvss
ACun8zXvWqJhTar+iJHiTJTWyQPE6es0V1SAw0RnTuLRRmtv/Q9Zx4YOH2d3JkOC
55mfgO3uNzw8fcJ5hoILHtXxhI2qtSkdydIFbE1U9CgBKE39Uo0VgFf9fl6VJRg=
=7a5a
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2020-07-20' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.9
First set of patches for v5.9. This comes later than usual as I was
offline for two weeks. The biggest change here is moving Microchip
wilc1000 driver from staging. There was an immutable topic branch with
one commit moving the whole driver and the topic branch was pulled
both to staging-next and wireless-drivers-next. At the moment the only
reported conflict is in MAINTAINERS file, so I'm hoping the move
should go smoothly.
Other notable changes are ath11k getting 6 GHz band support and rtw88
supporting RTL8821CE. And there's also the usual fixes, API changes
and cleanups all over.
Major changes:
wilc1000
* move from drivers/staging to drivers/net/wireless/microchip
ath11k
* add 6G band support
* add spectral scan support
iwlwifi
* make FW reconfiguration quieter by not using warn level
rtw88
* add support for RTL8821CE
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the regression introduced by commit c8685937d0 ("iwlwifi: move
pu devices to new table") by adding the ids and the configurations of
two missing Killer 1550 cards in order to configure and let them work
correctly again (following the new table convention).
Resolve bug 208141 ("Wireless ac 9560 not working kernel 5.7.2",
https://bugzilla.kernel.org/show_bug.cgi?id=208141).
Fixes: c8685937d0 ("iwlwifi: move pu devices to new table")
Signed-off-by: Alessio Bonfiglio <alessio.bonfiglio@mail.polimi.it>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200714091911.4442-1-alessio.bonfiglio@mail.polimi.it
Using uninitialized_var() is dangerous as it papers over real bugs[1]
(or can in the future), and suppresses unrelated compiler warnings
(e.g. "unused variable"). If the compiler thinks it is uninitialized,
either simply initialize the variable or make compiler changes.
In preparation for removing[2] the[3] macro[4], remove all remaining
needless uses with the following script:
git grep '\buninitialized_var\b' | cut -d: -f1 | sort -u | \
xargs perl -pi -e \
's/\buninitialized_var\(([^\)]+)\)/\1/g;
s:\s*/\* (GCC be quiet|to make compiler happy) \*/$::g;'
drivers/video/fbdev/riva/riva_hw.c was manually tweaked to avoid
pathological white-space.
No outstanding warnings were found building allmodconfig with GCC 9.3.0
for x86_64, i386, arm64, arm, powerpc, powerpc64le, s390x, mips, sparc64,
alpha, and m68k.
[1] https://lore.kernel.org/lkml/20200603174714.192027-1-glider@google.com/
[2] https://lore.kernel.org/lkml/CA+55aFw+Vbj0i=1TGqCR5vQkCzWJ0QxK6CernOU6eedsudAixw@mail.gmail.com/
[3] https://lore.kernel.org/lkml/CA+55aFwgbgqhbp1fkxvRKEpzyR5J8n1vKT1VZdz9knmPuXhOeg@mail.gmail.com/
[4] https://lore.kernel.org/lkml/CA+55aFz2500WfbKXAx8s67wrm9=yVJu65TpLgN_ybYNv0VEOKA@mail.gmail.com/
Reviewed-by: Leon Romanovsky <leonro@mellanox.com> # drivers/infiniband and mlx4/mlx5
Acked-by: Jason Gunthorpe <jgg@mellanox.com> # IB
Acked-by: Kalle Valo <kvalo@codeaurora.org> # wireless drivers
Reviewed-by: Chao Yu <yuchao0@huawei.com> # erofs
Signed-off-by: Kees Cook <keescook@chromium.org>
On failure pcie_capability_read_dword() sets it's last parameter, val
to 0. However, with Patch 14/14, it is possible that val is set to ~0 on
failure. This would introduce a bug because (x & x) == (~0 & x).
This bug can be avoided without changing the function's behaviour if the
return value of pcie_capability_read_dword is checked to confirm success.
Check the return value of pcie_capability_read_dword() to ensure success.
Suggested-by: Bjorn Helgaas <bjorn@helgaas.com>
Signed-off-by: Bolarinwa Olayemi Saheed <refactormyself@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200713175529.29715-3-refactormyself@gmail.com
The variable tid is being initialized with a value that is never read
and it is being updated later with a new value. The initialization is
redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200701135221.549700-1-colin.king@canonical.com
With legacy PM, drivers themselves were responsible for managing the
device's power states and takes care of register states.
After upgrading to the generic structure, PCI core will take care of
required tasks and drivers should do only device-specific operations.
The driver was invoking PCI helper functions like pci_save/restore_state(),
pci_enable/disable_device() and pci_set_power_state(), which is not
recommended.
Compile-tested only.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200629072525.156154-3-vaibhavgupta40@gmail.com
With legacy PM, drivers themselves were responsible for managing the
device's power states and takes care of register states.
After upgrading to the generic structure, PCI core will take care of
required tasks and drivers should do only device-specific operations.
The driver was invoking PCI helper functions like pci_save/restore_state(),
pci_enable/disable_device() and pci_set_power_state(), which is not
recommended.
Compile-tested only.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200629072525.156154-2-vaibhavgupta40@gmail.com
With legacy PM, drivers themselves were responsible for managing the
device's power states and takes care of register states.
After upgrading to the generic structure, PCI core will take care of
required tasks and drivers should do only device-specific operations.
In the case of adm8211, after removing PCI helper functions, .suspend()
and .resume() became empty-body functions. Hence, define them NULL and
use dev_pm_ops.
Compile-tested only.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200629035031.169670-1-vaibhavgupta40@gmail.com
With the support of generic PM callbacks, drivers no longer need to use
legacy .suspend() and .resume() in which they had to maintain PCI states
changes and device's power state themselves. The required operations are
done by PCI core.
PCI drivers are not expected to invoke PCI helper functions like
pci_save/restore_state(), pci_enable/disable_device(),
pci_set_power_state(), etc. Their tasks are completed by PCI core itself.
Compile-tested only.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200624174048.64754-1-vaibhavgupta40@gmail.com
Earlier, drivers had to manage the device's power states, and related
operations, themselves. With the generic approach, these are done by PCI
core.
The only driver-specific jobs, .suspend() and .resume() doing were invoking
PCI helper functions pci_save/restore_state() and
pci_set_power_state(). This is not recommeneded as PCI core takes care of
that. Hence they became empty-body functions, thus define them NULL.
Compile-tested only.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200623094454.12427-1-vaibhavgupta40@gmail.com
In case of an error, no one will use the allocated structure. Call
ieee80211_free_hw, same as in rtl_usb_disconnect.
Signed-off-by: Reto Schneider <code@reto-schneider.ch>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200622132113.14508-4-code@reto-schneider.ch
Prevent code from calling itself indirectly, causing the driver to hang
and consume 100% CPU.
Without this fix, the following script can bring down a single CPU
system:
```
while true; do
rmmod rtl8192cu
modprobe rtl8192cu
done
```
Signed-off-by: Reto Schneider <code@reto-schneider.ch>
ACKed-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200622132113.14508-2-code@reto-schneider.ch
Sparse reports the following issue:
CHECK drivers/net/wireless/realtek/rtlwifi/rtl8188ee/trx.c
drivers/net/wireless/realtek/rtlwifi/rtl8188ee/trx.c:500:26: warning: incorrect type in initializer (different base types)
drivers/net/wireless/realtek/rtlwifi/rtl8188ee/trx.c:500:26: expected restricted __le32 [usertype] *pdesc
drivers/net/wireless/realtek/rtlwifi/rtl8188ee/trx.c:500:26: got unsigned int [usertype] *
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200604005733.7905-3-Larry.Finger@lwfinger.net
In some b43 files, the wiki url is still the old
"wireless.kernel.org" instead of the new
"wireless.wiki.kernel.org"
Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200605154112.16277-6-f.suligoi@asem.it
In at76c50x-usb.c the wiki url is still the old
"wireless.kernel.org" instead of the new
"wireless.wiki.kernel.org"
Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200605154112.16277-5-f.suligoi@asem.it
The wiki url is still the old "wireless.kernel.org"
instead of the new "wireless.wiki.kernel.org"
Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200605154112.16277-3-f.suligoi@asem.it
Add a set of logic with corresponding coexistence parameters to
handle the situation under BT inquiry/page.
We will set PSTDMA while WL-Busy + BT inquiry/page to separate
WL/BT slots. PSTDMA can protect WL data rate and BT performance.
If WL-Busy + BT inquiry/page and there was BT device paired,
We will set the mechanism to 4Slot PSTDMA.
In 4Slot PSTDMA, the paired devices can perform more smoothly
and prevent some issues trigger from insufficient data.
And to avoid A2DP glitch or disconnection, we will adjust ACL
data priority higher than inquiry/page.
In addition, we found sometimes BT inquiry/page still working
last for seconds after BT had notified inquiry/page finished.
It will lead to A2DP glitch cause of ACL data, inquiry/page
priority toggled. To fix the corner, we add a timer to remain
the inquiry/page status.
And we found WL busy/idle threshold is too sensitive,
it will keep switching in some weak network environment and
coexistence mechanism will switch between TDMA and PSTDMA.
The very frequently switching may destroyed not only the
handshake with AP, but BT performance. And it will trigger
some unexpected error.
To prevent the frequently switching, we add a timer to delay
the status change while WL busy switch to idle.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200715023324.8600-1-yhchuang@realtek.com
The length of the key comes from the network and it's a 16 bit number. It
needs to be capped to prevent a buffer overflow.
Fixes: 5e6e3a92b9 ("wireless: mwifiex: initial commit for Marvell mwifiex driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Ganapathi Bhat <ganapathi.bhat@nxp.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200708115857.GA13729@mwanda
ENOTSUPP (double PP) is internal linux kernel code 524 available only in
kernel include file linux/errno.h and not exported to userspace.
EOPNOTSUPP (OP; double PP) is standard code 95 for reporting 'operation not
supported' available via kernel include file uapi/asm-generic/errno.h.
ENOTSUP (single P) is alias for EOPNOTSUPP defined only in userspace
include file bits/errno.h and not available in kernel.
Because Linux kernel does not support ENOTSUP (single P) and because
userspace does not support ENOTSUPP (double PP), report error code for
'operation not supported' via EOPNOTSUPP macro.
This patch fixes problem that mwifiex kernel driver sends to userspace
unsupported error codes like: "failed: -524 (No error information)".
After applying this patch userspace see: "failed: -95 (Not supported)".
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Ganapathi Bhat <ganapathi.bhat@nxp.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200703112151.18917-1-pali@kernel.org
We currently have a collection of flags and locking between the
threaded irq and tx work:
- wl->flags bitops
- wl->mutex
- wl->wl_lock spinlock
The bitops flags do not need a spinlock around them, and we only need
the spinlock to see if we need to queue tx work or not. And wlcore_irq()
holds the mutex.
To simplify the locking, we can use spin_trylock and always queue tx
work unless we know there's nothing to do.
Let's also update the comment a bit while at it.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200702162951.45392-4-tony@atomide.com
We currently have a collection of flags and locking between the
threaded irq and tx work:
- wl->flags bitops
- wl->mutex
- wl->wl_lock spinlock
The bitops flags do not need a spinlock around them, and
wlcore_irq() already holds the mutex calling wlcore_irq_locked().
And we only need the spinlock to see if we need to run the queue
or not.
To simplify the locking, we can use spin_trylock and always run the
tx queue unless we know there's nothing to do.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200702162951.45392-3-tony@atomide.com
We can simplify the runtime resume ELP path by always setting and
clearing the completion in runtime resume. This way we can test for
WL1271_FLAG_IRQ_RUNNING after the resume write to see if we need
completion at all.
And in wlcore_irq(), we need to take spinlock for running the
completion and for the pm_wakeup_event(). Spinlock is not needed
around the bitops flags check for WL1271_FLAG_SUSPENDED so the
spinlocked sections get shorter.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200702162951.45392-2-tony@atomide.com
This macro is already used in mwifiex driver for specifying upper limit and
is defined to value 3. So use it also in struct ieee80211_iface_limit.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200626152938.12737-1-pali@kernel.org
New device ID 0xc82f found on Lenovo ThinkCenter.
Tested it with c822 driver, works good.
PCI id:
03:00.0 Network controller [0280]: Realtek Semiconductor Co., Ltd.
Device [10ec:c82f]
Subsystem: Lenovo Device [17aa:c02f]
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200612082745.204400-1-aaron.ma@canonical.com
Some platforms cannot read the DBI register successfully for the
ASPM settings. After the read failed, the bus could be unstable,
and the device just became unavailable [1]. For those platforms,
the ASPM should be disabled. But as the ASPM can help the driver
to save the power consumption in power save mode, the ASPM is still
needed. So, add a module parameter for them to disable it, then
the device can still work, while others can benefit from the less
power consumption that brings by ASPM enabled.
[1] https://bugzilla.kernel.org/show_bug.cgi?id=206411
[2] Note that my lenovo T430 is the same.
Fixes: 3dff7c6e37 ("rtw88: allows to enable/disable HCI link PS mechanism")
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200605074703.32726-1-yhchuang@realtek.com
Since single rf path chips don't support TX SPBC, tell mac80211
to not advertise it.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200603094218.19942-5-yhchuang@realtek.com
Beamforming is used for directional signal transmission/reception.
Beamformee plays the role for signal reception, and makes the RX
performance better in middle distance range.
Implement beamformee related callbacks for 8821c.
Since 8821c only support 1ss rate, nc_index in beamformee setting
needs to be adjusted based on the capability.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200603094218.19942-4-yhchuang@realtek.com
The TX power requires to be adjusted based on the thermal value.
The actual power will decrease if the thermal value raised, and
will increase if the thermal value lowered. Driver comapres the
thermal value, as moving averages. If it changes over a limit,
driver will modify the TX power index to compensate.
Implement rtw_chip_ops::pwr_track() for 8821c.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200603094218.19942-3-yhchuang@realtek.com
CCK PD can reduce the number of false alarm of the CCK rates.
It dynamically adjusts the power threshold and CS ratio.
The values are compared to the values of the previous level, if
the level is changed, set new values of power threshold and CS
ratio.
Implement rtw_chip_ops::cck_pd_set() for 8821c.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200603094218.19942-2-yhchuang@realtek.com
In order to get a better TX EVM, do calibration after association.
The calibration needed for 8821c is the IQK, which is done in the
firmware. Implement the rtw_chip_ops::phy_calibration() to trigger
firmware to calibrate.
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200616091625.26489-8-yhchuang@realtek.com
False alarm statistics can be used to adjust the RX gain. This
helps the driver to adapt to different circumstances.
Implement rtw_chip_ops::false_alarm_statistics() for 8821c.
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200616091625.26489-7-yhchuang@realtek.com
Some RX packets contain also information about environment status.
Implement rtw_chip_ops::query_rx_desc() for 8821c. Parse the RX
descriptor which describes the current condition of the received
packet.
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200616091625.26489-6-yhchuang@realtek.com
8821c is capable of 2.4G and 5G.
Implement rtw_chip_ops::set_channel() to set 2G and 5G channels.
This includes MAC, BB and RF related settings.
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200616091625.26489-5-yhchuang@realtek.com
To improve user experience in field, we need DIG to adjust RX initial
gain depends on field situation.
Define the register addresses for 8821c.
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200616091625.26489-4-yhchuang@realtek.com
To configure the transmit power of 8821c implement trasmit
power index setting callback function for 8821c. This is very
similar to the callback function of 8822b.
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200616091625.26489-3-yhchuang@realtek.com
RTL8821CE chipsets are 802.11ac dual-band WiFi + BT combo chips.
This patch adds the basic functions such as parameter tables, chip
information, power on flow.
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200616091625.26489-2-yhchuang@realtek.com
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type defining 'NETDEV_TX_OK' but this
driver returns '0' instead of 'NETDEV_TX_OK'.
Fix this by returning 'NETDEV_TX_OK' instead of '0'.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200629104009.84077-1-luc.vanoostenryck@gmail.com
Added version number info along with firmware name so driver can pick
the correct revision of FW file. Moved FW filename macro as part of
driver code & added MODULE_FIRMWARE to specify FW needed by module.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200710051826.3267-6-ajay.kathat@microchip.com
Modify WILC1000 binary filename to use single unified wilc1000 FW.
A single wilc1000 binary is used for different wilc1000 revisions.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200710051826.3267-5-ajay.kathat@microchip.com
Avoid below reported warning found when 'CONFIG_PM' config is
undefined.
'warning: unused variable 'wowlan_support' [-Wunused-const-variable]'
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200710051826.3267-4-ajay.kathat@microchip.com
Make use 'strlcpy' instead of 'strncpy' to overcome 'stringop-truncation'
compiler warning.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200710051826.3267-3-ajay.kathat@microchip.com
The code in the BRCM80211 BRCMSMAC driver is using the legacy
GPIO API to to a complex check of the validity of the base of
the GPIO chip and whether it is present at all and then adding
an offset to the base of the chip.
Use the existing function to obtain a GPIO line internally
from a GPIO chip so we can use the offset directly and
modernize the code to use GPIO descriptors instead of integers
from the global GPIO numberspace.
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Frank Kao <frank.kao@cypress.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200711210150.4943-1-linus.walleij@linaro.org
The driver relies on the compatible string from DT to determine which
FW configuration file it should load. The DTS spec allows for '/' as
part of the compatible string. We change this to '-' so that we will
still be able to load the config file, even when the compatible has a
'/'. This fixes explicitly the firmware loading for
"solidrun,cubox-i/q".
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Reviewed-by: Hans deGoede <hdegoede@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200701112201.6449-1-matthias.bgg@kernel.org
Linux 3.6 introduces TSQ which has a per socket threshold for TCP Tx
packet to reduce latency. In flow control mode, host driver enqueues skb
in hanger and TCP doesn't push new skb frees until host frees the skb when
receiving fwstatus event. So set pacing shift 8 to send them as a single
large aggregate frame to the bus layer.
43455 TX TCP throughput in different FC modes on Linux 5.4.18
sk_pacing_shift : Throughput (fcmode=0)
10: 245 Mbps
9: 245 Mbps
8: 246 Mbps
7: 246 Mbps
sk_pacing_shift : Throughput (fcmode=1)
10: 182 Mbps
9: 197 Mbps
8: 206 Mbps
7: 207 Mbps
sk_pacing_shift : Throughput (fcmode=2)
10: 180 Mbps
9: 197 Mbps
8: 206 Mbps
7: 207 Mbps
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200624091608.25154-3-wright.feng@cypress.com
When USB or SDIO device got abnormal bus disconnection, host driver
tried to clean up the skbs in PSQ and TXQ (The skb's pointer in hanger
slot linked to PSQ and TSQ), so we should set the state of skb hanger slot
to BRCMF_FWS_HANGER_ITEM_STATE_FREE before freeing skb.
In brcmf_fws_bus_txq_cleanup it already sets
BRCMF_FWS_HANGER_ITEM_STATE_FREE before freeing skb, therefore we add the
same thing in brcmf_fws_psq_flush to avoid following warning message.
[ 1580.012880] ------------ [ cut here ]------------
[ 1580.017550] WARNING: CPU: 3 PID: 3065 at
drivers/net/wireless/broadcom/brcm80211/brcmutil/utils.c:49
brcmu_pkt_buf_free_skb+0x21/0x30 [brcmutil]
[ 1580.184017] Call Trace:
[ 1580.186514] brcmf_fws_cleanup+0x14e/0x190 [brcmfmac]
[ 1580.191594] brcmf_fws_del_interface+0x70/0x90 [brcmfmac]
[ 1580.197029] brcmf_proto_bcdc_del_if+0xe/0x10 [brcmfmac]
[ 1580.202418] brcmf_remove_interface+0x69/0x190 [brcmfmac]
[ 1580.207888] brcmf_detach+0x90/0xe0 [brcmfmac]
[ 1580.212385] brcmf_usb_disconnect+0x76/0xb0 [brcmfmac]
[ 1580.217557] usb_unbind_interface+0x72/0x260
[ 1580.221857] device_release_driver_internal+0x141/0x200
[ 1580.227152] device_release_driver+0x12/0x20
[ 1580.231460] bus_remove_device+0xfd/0x170
[ 1580.235504] device_del+0x1d9/0x300
[ 1580.239041] usb_disable_device+0x9e/0x270
[ 1580.243160] usb_disconnect+0x94/0x270
[ 1580.246980] hub_event+0x76d/0x13b0
[ 1580.250499] process_one_work+0x144/0x360
[ 1580.254564] worker_thread+0x4d/0x3c0
[ 1580.258247] kthread+0x109/0x140
[ 1580.261515] ? rescuer_thread+0x340/0x340
[ 1580.265543] ? kthread_park+0x60/0x60
[ 1580.269237] ? SyS_exit_group+0x14/0x20
[ 1580.273118] ret_from_fork+0x25/0x30
[ 1580.300446] ------------ [ cut here ]------------
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200624091608.25154-2-wright.feng@cypress.com
commit 4684997d9e ("brcmfmac: reset PCIe bus on a firmware crash")
adds a reset function to recover firmware trap for PCIe bus. This commit
adds an implementation for SDIO bus.
Upon SDIO firmware trap, do below:
- Remove the device
- Reset hardware
- Probe the device again
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200622144851.165248-1-chi-hsien.lin@cypress.com
Ignore FW event if the event's BSSID is different form the BSSID of the
currently connected AP. Check interface state is connected or not, if
state is not connected that can ignore link down event.
Signed-off-by: Able Liao <Able.Liao@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200618160739.21457-4-chi-hsien.lin@cypress.com
Current brcmf_link_down() always call cfg80211_disconnected() with
locally_generated=1, which is not always the case. Add event source
argument on link down handler and set locally_generated based on the
real trigger.
Signed-off-by: Soontak Lee <soontak.lee@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200618160739.21457-3-chi-hsien.lin@cypress.com
Unable to change back to visiable SSID because there is
no disable hidden ssid routine.
Signed-off-by: Soontak Lee <soontak.lee@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200618160739.21457-2-chi-hsien.lin@cypress.com
Commit 4905432b28b7 ("brcmfmac: Fix P2P Group Formation failure via Go-neg
method") did not initialize requested_dwell properly, resulting in an
always-false dwell time overflow check. Fix it by setting the correct
requested_dwell value.
Fixes: 4905432b28b7 ("brcmfmac: Fix P2P Group Formation failure via Go-neg method")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Joseph Chuang <joseph.chuang@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200610152106.175257-7-chi-hsien.lin@cypress.com
This patch move the credit map setting to right place to avoid
brcmf_fws_return_credits() return without setting the credit map.
It fix the thoughput zero stalls issue in softAP mode when STA
using PM 1 mode.
Signed-off-by: Double Lo <double.lo@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200610152106.175257-6-chi-hsien.lin@cypress.com
There is a mismatch of tx status flag values between host and firmware.
It makes the host mistake the flags and have incorrect behavior of credit
returns. So update the flags to sync with the firmware ones.
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200610152106.175257-5-chi-hsien.lin@cypress.com
It is observed that sometimes when sdiod is low in tx credits in low
rssi scenarios, the data path consumes all sdiod rx all credits and
there is no sdiod rx credit available for control path causing host
and card to go out of sync resulting in link loss between host and
card. So in order to prevent it some credits are reserved for control
path.
Note that TXCTL_CREDITS can't be larger than the firmware default
credit update threshold 2; otherwise there will be a deadlock for both
side waiting for each other.
Signed-off-by: Amar Shankar <amsr@cypress.com>
Signed-off-by: Jia-Shyr Chuang <joseph.chuang@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200610152106.175257-4-chi-hsien.lin@cypress.com
In wifi firmware, max length of IOCTL/IOVAR buffer size is 8192.
Increase the message buffer max size same as wifi firmware for control
packets so return buffers can come back.
Signed-off-by: Soontak Lee <soontak.lee@cypress.com>
Signed-off-by: Jia-Shyr Chuang <joseph.chuang@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200610152106.175257-3-chi-hsien.lin@cypress.com
Current credit borrowing allows only the access category BE to
borrow the credits. This change is to fix the credit borrowing
logic, to make borrowing available for all access categories
and also to borrow only from the lower categories. This fixes WFA
802.11n certs 5.2.27 failures.
Signed-off-by: Raveendran Somu <raveendran.somu@cypress.com>
Signed-off-by: Jia-Shyr Chuang <joseph.chuang@cypress.com>
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200610152106.175257-2-chi-hsien.lin@cypress.com
Bss info flag definition need to be fixed from 0x2 to 0x4
This flag is for rssi info received on channel.
All Firmware branches defined as 0x4 and this is bug in brcmfmac.
Signed-off-by: Prasanna Kerekoppa <prasanna.kerekoppa@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200604071835.3842-6-wright.feng@cypress.com
The firmware state machines are not fully suitable for concurrent
station interface support, it may hit unexpected error if we have 2
different SSIDs and the roaming scenarios concurrently.
To avoid the bad user-experience if this is not fully validated, we
dis-allow user to create two concurrent station interfaces.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200604071835.3842-5-wright.feng@cypress.com
brcmfmac host driver makes SDIO bus sleep and stops SDIO watchdog if no
pending event or data. As a result, host driver does not poll firmware
console buffer before buffer overflow, which leads to missing firmware
logs. We should not stop SDIO watchdog if console_interval is non-zero
in debug build.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200604071835.3842-4-wright.feng@cypress.com
When host driver retrieves mac addresses from dongle, driver copies memory
from drvr->mac to perm_addr. But at the moment, drvr->mac is all zero
array which causes permanent MAC address in wiphy is all zero as well.
To fix this, we set drvr->mac before setting perm_addr.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200604071835.3842-3-wright.feng@cypress.com
To truncate the additional bytes, if extra bytes have been received.
Current code only have a warning and proceed without handling it.
But in one of the crash reported by DVT, these causes the
crash intermittently. So the processing is limit to the skb->len.
Signed-off-by: Raveendran Somu <raveendran.somu@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200604071835.3842-2-wright.feng@cypress.com
First set of fixes for v5.8. Various important fixes for iwlwifi and
mt76.
iwlwifi
* fix sleeping under RCU
* fix a kernel crash when using compressed firmware images
mt76
* tx queueing fixes for mt7615/22/63
* locking fix
* fix a crash during watchdog reset
* fix memory leaks
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJfDJcKAAoJEG4XJFUm622boM4H+wTnBdnamYPASeJ8la5D5hyk
pXcPFYwTVjC48Cs+XWpcib2AQxrgZV8fF9SdbZqqCleZGGXSXsQb6WiaSr7JxFso
gbSaUHhYpfSOXdadNBI0ho/E+NFEsnIcIxMS2BJQTe9AUXCFY3oX56ut0ioSKx4P
rkgqTe0pvYUvLR4EOwCCWUndfrAgARy2KXqNsTmCCb5tXJf2leAjGyVRteX9RJQq
GSooKPrOJRLAiyId17D7kLPc8WHVv1KxBbRUgyC046s67CzDSEBw1jOy6Q2oncvI
ZCow/i7AuZSeSw3t6HRuy4ArMuRCafk1gKEbKw6TTVg47iGHn7JqrCs+l5do7hE=
=10X3
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-2020-07-13' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for v5.8
First set of fixes for v5.8. Various important fixes for iwlwifi and
mt76.
iwlwifi
* fix sleeping under RCU
* fix a kernel crash when using compressed firmware images
mt76
* tx queueing fixes for mt7615/22/63
* locking fix
* fix a crash during watchdog reset
* fix memory leaks
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This is an immutable branch shared between wireless-drivers-next and
staging-next for moving wilc1000 driver out of staging to drivers/net/wireless
directory.
Some thermal zone devices never change their state, so they should be
always enabled.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200629122925.21729-9-andrzej.p@collabora.com
Organize driver documentation by device type. Most documents
have fairly verbose yet uninformative names, so let users
first select a well defined device type, and then search for
a particular driver.
While at it rename the section from Vendor drivers to
Hardware drivers. This seems more accurate, besides people
sometimes refer to out-of-tree drivers as vendor drivers.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
The napi_gro_receive function no longer returns GRO_DROP ever, making
handling GRO_DROP dead code. This commit removes that dead code.
Further, it's not even clear that device drivers have any business in
taking action after passing off received packets; that's arguably out of
their hands. In this case, too, the non-gro path didn't bother checking
the return value. Plus, this had some clunky debugging functions that
duplicated code from elsewhere and was generally pretty messy. So, this
commit cleans that all up too.
Fixes: 6570bc79c0 ("net: core: use listified Rx for GRO_NORMAL in napi_gro_receive()")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid adding MT7615_EEPROM_SIZE twice.
Rename MT7615_EEPROM_EXTRA_DATA to MT7615_EEPROM_FULL_SIZE, since it already
includes MT7615_EEPROM_SIZE
Fixes: ad380ad1eb ("mt76: mt7615: add support for applying DC offset calibration from EEPROM")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200622150716.49622-1-nbd@nbd.name
Fix the two following memory leaks in mt7663u_probe:
1- if device power-own times out, remove ieee80211 hw device.
2- if mt76u queues allocation fails, remove pending urbs.
Fixes: eb99cc95c3 ("mt76: mt7615: introduce mt7663u support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/e4098f0c8a9ac51997de07f38c2bcdf7042d6db1.1592755166.git.lorenzo@kernel.org
Fixes a crash on MMIO devices when running into the watchdog reset
Fixes: d3377b78ce ("mt76: add HE phy modes and hardware queue")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200615181341.81871-1-nbd@nbd.name
* tx queueing fixes for mt7615/22/63
* locking fix
-----BEGIN PGP SIGNATURE-----
Comment: GPGTools - http://gpgtools.org
iEYEABECAAYFAl7dBRsACgkQ130UHQKnbvUpiQCgjHAeT1fOKnFfFF5kHzECEyFS
1N8An0endTyFWAXCZd3aEgK4/nQN4LwR
=6f32
-----END PGP SIGNATURE-----
Merge tag 'mt76-for-kvalo-2020-06-07' of https://github.com/nbd168/wireless
mt76 patches for 5.8
* tx queueing fixes for mt7615/22/63
* locking fix
# gpg: Signature made Sun 07 Jun 2020 06:17:47 PM EEST using DSA key ID 02A76EF5
# gpg: Good signature from "Felix Fietkau <nbd@nbd.name>"
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 75D1 1A7D 91A7 710F 4900 42EF D77D 141D 02A7 6EF5
* Fix links to wiki;
* Some preparations for gcc-10;
* Make FW reconfiguration quieter by not using warn level;
* Some other small fixes and clean-up;
-----BEGIN PGP SIGNATURE-----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=MRiL
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2020-06-11' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
First set of patches intended for v5.9
* Fix links to wiki;
* Some preparations for gcc-10;
* Make FW reconfiguration quieter by not using warn level;
* Some other small fixes and clean-up;
# gpg: Signature made Thu 11 Jun 2020 12:03:51 PM EEST using RSA key ID 1A3CC5FA
# gpg: Good signature from "Luciano Roth Coelho (Luca) <luca@coelho.fi>"
# gpg: aka "Luciano Roth Coelho (Intel) <luciano.coelho@intel.com>"
Currently need ptk/gtk wmi peer flags in wmi peer assoc cmd
are set based on the rsnie and wpaie of the bss from the bss list.
Since this bss list is not updated with current BSSID for AP mode,
we may not find bss from the bss list. Which results in ptk/gtk peer
flags are not set in the wmi peer assoc cmd. Due to this EAPOL frames
are going in data rates instead of management rates.
Tested-on: IPQ8074 WLAN.HK.2.1.0.1-01228-QCAHKSWPL_SILICONZ-1
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1591771841-25503-1-git-send-email-vnaralas@codeaurora.org
Add support for collecting and dumping the ring backpressure
stats via debugfs. Stats are dumped only if events are
received for the specific ring.
Below command can be used to obtain these stats as part of soc dp stats.
cat /sys/kernel/debug/ath11k/ipq8074/soc_dp_stats
Sample Output - When No stats available:
Backpressure Stats
==================
No Ring Backpressure stats received
Sample Output - When ring bp stats available for specific ring
Backpressure Stats
==================
Ring: REO2SW1_RING
count: 1
hp: 2
tp: 2
seen before: 4ms
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01213-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1591768308-32005-3-git-send-email-srirrama@codeaurora.org
Add support for dp tx error stats which logs tx failure reasons due
to ring full condition, etc. This stats is added in soc_dp_stats
which was earlier used as soc_rx_stats so that all dp related info
are logged in same file.
Below is an example usage,
root@OpenWrt:/# cat /sys/kernel/debug/ath11k/ipq8074/soc_dp_stats
SOC RX STATS:
err ring pkts: 0
Invalid RBM: 0
<snip>
SOC TX STATS:
Ring Full Failures:
ring0: 4
ring1: 3
ring2: 5
Misc Transmit Failures: 2
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01213-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1591768308-32005-2-git-send-email-srirrama@codeaurora.org
spectral scan control interface is exposed through debugfs eentry.
Relayfs is used to collect the spectral data. These interfaces are
similar to ath10k spectral.
spectral debugfs interfaces are below,
echo background > /sys/kernel/debug/ieee80211/phy0/ath11k/spectral_scan_ctl
echo trigger > /sys/kernel/debug/ieee80211/phy0/ath11k/spectral_scan_ctl
iw dev wlan0 scan
echo disable > /sys/kernel/debug/ieee80211/phy0/ath11k/spectral_scan_ctl
cat /sys/kernel/debug/ieee80211/phy0/ath11k/spectral_scan0 > fft_samples.dump
Tested-on: IPQ8074 WLAN.HK.2.1.0.1-01228-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1591688014-26441-2-git-send-email-periyasa@codeaurora.org
Add direct buffer ring (dbring) with helper API, which is used by the
spectral scan. Initialise the direct buffer ring based on the dma ring
capability, which get announced in the wmi service ready extended event.
This ring is slightly changed from data path rings. Compare to data path
ring this ring shares the hp and tp address to firmware though WMI commands.
Also the replenish buffer size is derived from firmware announcement.
driver receive indication through WMI event
WMI_PDEV_DMA_RING_BUF_RELEASE_EVENTID.
Tested-on: IPQ8074 WLAN.HK.2.1.0.1-01228-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1591688014-26441-1-git-send-email-periyasa@codeaurora.org
Pull networking fixes from David Miller:
1) Fix cfg80211 deadlock, from Johannes Berg.
2) RXRPC fails to send norigications, from David Howells.
3) MPTCP RM_ADDR parsing has an off by one pointer error, fix from
Geliang Tang.
4) Fix crash when using MSG_PEEK with sockmap, from Anny Hu.
5) The ucc_geth driver needs __netdev_watchdog_up exported, from
Valentin Longchamp.
6) Fix hashtable memory leak in dccp, from Wang Hai.
7) Fix how nexthops are marked as FDB nexthops, from David Ahern.
8) Fix mptcp races between shutdown and recvmsg, from Paolo Abeni.
9) Fix crashes in tipc_disc_rcv(), from Tuong Lien.
10) Fix link speed reporting in iavf driver, from Brett Creeley.
11) When a channel is used for XSK and then reused again later for XSK,
we forget to clear out the relevant data structures in mlx5 which
causes all kinds of problems. Fix from Maxim Mikityanskiy.
12) Fix memory leak in genetlink, from Cong Wang.
13) Disallow sockmap attachments to UDP sockets, it simply won't work.
From Lorenz Bauer.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (83 commits)
net: ethernet: ti: ale: fix allmulti for nu type ale
net: ethernet: ti: am65-cpsw-nuss: fix ale parameters init
net: atm: Remove the error message according to the atomic context
bpf: Undo internal BPF_PROBE_MEM in BPF insns dump
libbpf: Support pre-initializing .bss global variables
tools/bpftool: Fix skeleton codegen
bpf: Fix memlock accounting for sock_hash
bpf: sockmap: Don't attach programs to UDP sockets
bpf: tcp: Recv() should return 0 when the peer socket is closed
ibmvnic: Flush existing work items before device removal
genetlink: clean up family attributes allocations
net: ipa: header pad field only valid for AP->modem endpoint
net: ipa: program upper nibbles of sequencer type
net: ipa: fix modem LAN RX endpoint id
net: ipa: program metadata mask differently
ionic: add pcie_print_link_status
rxrpc: Fix race between incoming ACK parser and retransmitter
net/mlx5: E-Switch, Fix some error pointer dereferences
net/mlx5: Don't fail driver on failure to create debugfs
net/mlx5e: CT: Fix ipv6 nat header rewrite actions
...
Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
With addition of 6Ghz channels, it is possible that wmi buffer size can
exceed the maximum wmi buffer size. So iterate over the channel list,
and send multiple messages till channel list is empty.
Also mark PSC channel flag for 6GHz channels accordingly.
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200603001724.12161-8-pradeepc@codeaurora.org
If 6 ghz channel is a Preferred Scanning Channel(PSC), mark
the channel flag accordingly when updating channel list to firmware.
This will be used when making scanning decision in 6GHz channels.
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200603001724.12161-6-pradeepc@codeaurora.org
This adds support required for configuring min_data_rate of 6GHz oper IE
and peer_he_caps_6ghz in peer assoc command. The Minimum Rate field
indicates the minimum rate, in units of 1 Mb/s, that the non-AP STA is
allowed to use for sending PPDUs as defined in IEEE P802.11ax™/D6.0.
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200603001724.12161-5-pradeepc@codeaurora.org
As 6GHz cahnnel numbers overlap with those of 5GHz and 2GHz bands,
it is necessary to use frequency when determining the band info
in rx path.
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200603001724.12161-4-pradeepc@codeaurora.org
In some Intel files, the wiki url is still the old
"wireless.kernel.org" instead of the new
"wireless.wiki.kernel.org"
Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
Link: https://lore.kernel.org/r/20200605154112.16277-7-f.suligoi@asem.it
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
sizeof(flexible-array-member) triggers a warning because flexible array
members have incomplete type[1]. There are some instances of code in
which the sizeof operator is being incorrectly/erroneously applied to
zero-length arrays and the result is zero. Such instances may be hiding
some bugs. So, this work (flexible-array member conversions) will also
help to get completely rid of those sorts of issues.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20200507185538.GA14674@embeddedor
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The dynamic key update for addr_list_lock still causes troubles,
for example the following race condition still exists:
CPU 0: CPU 1:
(RCU read lock) (RTNL lock)
dev_mc_seq_show() netdev_update_lockdep_key()
-> lockdep_unregister_key()
-> netif_addr_lock_bh()
because lockdep doesn't provide an API to update it atomically.
Therefore, we have to move it back to static keys and use subclass
for nest locking like before.
In commit 1a33e10e4a ("net: partially revert dynamic lockdep key
changes"), I already reverted most parts of commit ab92d68fc2
("net: core: add generic lockdep keys").
This patch reverts the rest and also part of commit f3b0a18bb6
("net: remove unnecessary variables and callback"). After this
patch, addr_list_lock changes back to using static keys and
subclasses to satisfy lockdep. Thanks to dev->lower_level, we do
not have to change back to ->ndo_get_lock_subclass().
And hopefully this reduces some syzbot lockdep noises too.
Reported-by: syzbot+f3a0e80c34b3fc28ac5e@syzkaller.appspotmail.com
Cc: Taehee Yoo <ap420073@gmail.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc-10 complains when a zero-length array is accessed:
drivers/net/wireless/intel/iwlwifi/mvm/tx.c: In function 'iwl_mvm_rx_ba_notif':
drivers/net/wireless/intel/iwlwifi/mvm/tx.c:1929:17: warning: array subscript 9 is outside the bounds of an interior zero-length array 'struct iwl_mvm_compressed_ba_tfd[0]' [-Wzero-length-bounds]
1929 | &ba_res->tfd[i];
| ~~~~~~~~~~~^~~
In file included from drivers/net/wireless/intel/iwlwifi/mvm/../fw/api/tdls.h:68,
from drivers/net/wireless/intel/iwlwifi/mvm/fw-api.h:68,
from drivers/net/wireless/intel/iwlwifi/mvm/sta.h:73,
from drivers/net/wireless/intel/iwlwifi/mvm/mvm.h:83,
from drivers/net/wireless/intel/iwlwifi/mvm/tx.c:72:
drivers/net/wireless/intel/iwlwifi/mvm/../fw/api/tx.h:769:35: note: while referencing 'tfd'
769 | struct iwl_mvm_compressed_ba_tfd tfd[0];
| ^~~
Change this structure to use a flexible-array member for 'tfd' instead,
along with the various structures using an zero-length ieee80211_hdr
array that do not show warnings today but might be affected by similar
issues in the future.
Fixes: 6f68cc367a ("iwlwifi: api: annotate compressed BA notif array sizes")
Fixes: c46e7724bf ("iwlwifi: mvm: support new BA notification response")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20200430213101.135134-3-arnd@arndb.de
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In some ath files, the wiki url is still the old
"wireless.kernel.org" instead of the new
"wireless.wiki.kernel.org"
Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200605154112.16277-4-f.suligoi@asem.it
ath10k_htt_tx_free_msdu_id() has a lockdep assertion that htt->tx_lock
is held. Acquire the lock in a couple of error paths when calling that
function to ensure this condition is met.
Fixes: 6421969f24 ("ath10k: refactor tx pending management")
Fixes: e62ee5c381 ("ath10k: Add support for htt_data_tx_desc_64 descriptor")
Signed-off-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200604105901.1.I5b8b0c7ee0d3e51a73248975a9da61401b8f3900@changeid
The variable ret is being assigned with a value that is never read
and it is being updated later with a new value. The initialization is
redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20200420222449.99481-1-colin.king@canonical.com
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The correct variable name was replaced here by mistake by commit
ab27926d9e ("iwlwifi: fix devices with PCI Device ID 0x34F0 and 11ac RF
modules").
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Link: https://lore.kernel.org/r/20200210135817.31994-1-luca@lucaceresoli.net
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
On AX200, the average power was showing positive instead of negative, but
otherwise matched the expected RSSI. Flip the value to negative before
giving to mac80211.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Link: https://lore.kernel.org/r/20191126214744.1283-1-greearb@candelatech.com
[removed unnecessary check and some unnecessary parentheses]
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
IWL_WARN seems excessive here since this can happen during normal
operation. Every time I connect to a new network with 8086:24fd I get
this as KERN_WARNING on the console, which mildly distracts from other
more pressing messages. For example:
% sudo journalctl _TRANSPORT=kernel | grep -c 'FW already configured'
403
Signed-off-by: Chris Down <chris@chrisdown.name>
Cc: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-wireless@vger.kernel.org
Link: https://lore.kernel.org/r/20191017144841.GA16393@chrisdown.name
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Overwrite hw queue id for non-bufferable management frames if the hw
support always txq (altxq) in order to be in sync with mac txwi code
Fixes: cdad487405 ("mt76: mt7615: add dma and tx queue initialization for MT7622")
Fixes: f40ac0f3d3 ("mt76: mt7615: introduce mt7663e support")
Suggested-by: Felix Fietkau <nbd@nbd.name>
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
mt7622/mt7663 chipsets rely on a fixed reverse queue map order respect
to mac80211 one:
- q(0): IEEE80211_AC_BK
- q(1): IEEE80211_AC_BE
- q(2): IEEE80211_AC_VI
- q(3): IEEE80211_AC_VO
Fixes: cdad487405 ("mt76: mt7615: add dma and tx queue initialization for MT7622")
Fixes: f40ac0f3d3 ("mt76: mt7615: introduce mt7663e support")
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Co-developed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
acs and wmm index are swapped in mt7615_queues_acq respect to the hw
design
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Coverage class callback can potentially run in parallel with other
routines (e.g. mt7615_set_channel) that configures timing registers.
Run coverage class callback holding mt76 mutex
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
All iwlwifi cards below the 22000 series are able to handle multiple
keyids per STA and allow the selection of the encryption key per MPDU.
These are therefore fully compatible with the Extended Key ID support
implementation in mac80211.
Enable Extended Key ID support for all dvm cards and the mvm cards not
using the incompatible new Tx API introduced for the 22000 series.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Link: https://lore.kernel.org/r/20190819180540.2855-1-alexander@wetzel-home.de
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Pull networking updates from David Miller:
1) Allow setting bluetooth L2CAP modes via socket option, from Luiz
Augusto von Dentz.
2) Add GSO partial support to igc, from Sasha Neftin.
3) Several cleanups and improvements to r8169 from Heiner Kallweit.
4) Add IF_OPER_TESTING link state and use it when ethtool triggers a
device self-test. From Andrew Lunn.
5) Start moving away from custom driver versions, use the globally
defined kernel version instead, from Leon Romanovsky.
6) Support GRO vis gro_cells in DSA layer, from Alexander Lobakin.
7) Allow hard IRQ deferral during NAPI, from Eric Dumazet.
8) Add sriov and vf support to hinic, from Luo bin.
9) Support Media Redundancy Protocol (MRP) in the bridging code, from
Horatiu Vultur.
10) Support netmap in the nft_nat code, from Pablo Neira Ayuso.
11) Allow UDPv6 encapsulation of ESP in the ipsec code, from Sabrina
Dubroca. Also add ipv6 support for espintcp.
12) Lots of ReST conversions of the networking documentation, from Mauro
Carvalho Chehab.
13) Support configuration of ethtool rxnfc flows in bcmgenet driver,
from Doug Berger.
14) Allow to dump cgroup id and filter by it in inet_diag code, from
Dmitry Yakunin.
15) Add infrastructure to export netlink attribute policies to
userspace, from Johannes Berg.
16) Several optimizations to sch_fq scheduler, from Eric Dumazet.
17) Fallback to the default qdisc if qdisc init fails because otherwise
a packet scheduler init failure will make a device inoperative. From
Jesper Dangaard Brouer.
18) Several RISCV bpf jit optimizations, from Luke Nelson.
19) Correct the return type of the ->ndo_start_xmit() method in several
drivers, it's netdev_tx_t but many drivers were using
'int'. From Yunjian Wang.
20) Add an ethtool interface for PHY master/slave config, from Oleksij
Rempel.
21) Add BPF iterators, from Yonghang Song.
22) Add cable test infrastructure, including ethool interfaces, from
Andrew Lunn. Marvell PHY driver is the first to support this
facility.
23) Remove zero-length arrays all over, from Gustavo A. R. Silva.
24) Calculate and maintain an explicit frame size in XDP, from Jesper
Dangaard Brouer.
25) Add CAP_BPF, from Alexei Starovoitov.
26) Support terse dumps in the packet scheduler, from Vlad Buslov.
27) Support XDP_TX bulking in dpaa2 driver, from Ioana Ciornei.
28) Add devm_register_netdev(), from Bartosz Golaszewski.
29) Minimize qdisc resets, from Cong Wang.
30) Get rid of kernel_getsockopt and kernel_setsockopt in order to
eliminate set_fs/get_fs calls. From Christoph Hellwig.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2517 commits)
selftests: net: ip_defrag: ignore EPERM
net_failover: fixed rollback in net_failover_open()
Revert "tipc: Fix potential tipc_aead refcnt leak in tipc_crypto_rcv"
Revert "tipc: Fix potential tipc_node refcnt leak in tipc_rcv"
vmxnet3: allow rx flow hash ops only when rss is enabled
hinic: add set_channels ethtool_ops support
selftests/bpf: Add a default $(CXX) value
tools/bpf: Don't use $(COMPILE.c)
bpf, selftests: Use bpf_probe_read_kernel
s390/bpf: Use bcr 0,%0 as tail call nop filler
s390/bpf: Maintain 8-byte stack alignment
selftests/bpf: Fix verifier test
selftests/bpf: Fix sample_cnt shared between two threads
bpf, selftests: Adapt cls_redirect to call csum_level helper
bpf: Add csum_level helper for fixing up csum levels
bpf: Fix up bpf_skb_adjust_room helper's skb csum setting
sfc: add missing annotation for efx_ef10_try_update_nic_stats_vf()
crypto/chtls: IPv6 support for inline TLS
Crypto/chcr: Fixes a coccinile check error
Crypto/chcr: Fixes compilations warnings
...
Firmware for sd8997 chipset is distributed by Marvell package and also as
part of the linux-firmware repository in filename sdsd8997_combo_v4.bin.
This patch fixes mwifiex driver to load correct firmware file for sd8997.
Fixes: 6d85ef00d9 ("mwifiex: add support for 8997 chipset")
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Ganapathi Bhat <ganapathi.bhat@nxp.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Firmware for sd8977 chipset is distributed by Marvell package and also as
part of the linux-firmware repository in filename sdsd8977_combo_v2.bin.
This patch fixes mwifiex driver to load correct firmware file for sd8977.
Fixes: 1a0f547831 ("mwifiex: add support for sd8977 chipset")
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Ganapathi Bhat <ganapathi.bhat@nxp.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
* many 6 GHz changes, though it's not _quite_ complete
(I left out scanning for now, we're still discussing)
* allow userspace SA-query processing for operating channel
validation
* TX status for control port TX, for AP-side operation
* more per-STA/TID control options
* move to kHz for channels, for future S1G operation
* various other small changes
-----BEGIN PGP SIGNATURE-----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=wdaG
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2020-05-31' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Another set of changes, including
* many 6 GHz changes, though it's not _quite_ complete
(I left out scanning for now, we're still discussing)
* allow userspace SA-query processing for operating channel
validation
* TX status for control port TX, for AP-side operation
* more per-STA/TID control options
* move to kHz for channels, for future S1G operation
* various other small changes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
