These laptops support both headphone, headset and mic modes
for the 3.5mm jack.
Cc: stable@vger.kernel.org
BugLink: https://bugs.launchpad.net/bugs/1526330
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If driver received a message that it can't handle, it won't
clear the corresponding bit and unmask interrupt, this may
lock the IRQ and DSP can't send message anymore.
To fix the issue, we should Always update IMRX after IPC.
Here we always clear the DONE/BUSY bit and unmask the IRQ
source, even when IPC failures have occurred previously.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Modified-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Avoid getting sample rate on AudioQuest DragonFly as it is unsupported
and causes noisy "cannot get freq at ep 0x1" messages when playback
starts.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
AudioQuest DragonFly DAC reports a volume control range of 0..50
(0x0000..0x0032) which in USB Audio means a range of 0 .. 0.2dB, which
is obviously incorrect and would cause software using the dB information
in e.g. volume sliders to have a massive volume difference in 100..102%
range.
Commit 2d1cb7f658 ("ALSA: usb-audio: add dB range mapping for some
devices") added a dB range mapping for it with range 0..50 dB.
However, the actual volume mapping seems to be neither linear volume nor
linear dB scale, but instead quite close to the cubic mapping e.g.
alsamixer uses, with a range of approx. -53...0 dB.
Replace the previous quirk with a custom dB mapping based on some basic
output measurements, using a 10-item range TLV (which will still fit in
alsa-lib MAX_TLV_RANGE_SIZE).
Tested on AudioQuest DragonFly HW v1.2. The quirk is only applied if the
range is 0..50, so if this gets fixed/changed in later HW revisions it
will no longer be applied.
v2: incorporated Takashi Iwai's suggestion for the quirk application
method
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add support for PA gpio pin for controlling an external amplifier as used
on some Allwinner boards.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Rename the codec dapm widgets and routes with a _codec prefix. This is
a preparation patch for adding card dapm widgets and routes.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DPCM does not fully support symmetry attributes. soc_pcm_apply_symmetry()
is skipped in soc_pcm_open() for DPCM, without being applied elsewhere.
So HW parameters cannot be correctly limited, and user space can do
playback/capture at different rates while HW actually does not support it.
soc_pcm_params_symmetry() will return error and the second stream stops.
This patch adds soc_pcm_apply_symmetry() for FE, BE, and codec DAIs
in DPCM path that was skipped in soc_pcm_open().
Signed-off-by: PC Liao <pc.liao@mediatek.com>
Signed-off-by: Koro Chen <koro.chen@mediatek.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add code to unregister codec in probe function,
when the error occurs after the codec is registered.
Signed-off-by: Songjun Wu <songjun.wu@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Locking is currently missing from the DSP firmware controls, which can
lead to some race conditions if the controls are accessed as the DSP
powers up or down. This patch adds them to the new power lock.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We should hold the DSP power lock whilst changing the firmware since we
need to check if it is running first.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Most events around the DSP just need to be locked to ensure that the DSP
can't change power state whilst they are happening. This includes the
debugfs entries and this will make sorting the rest of the locking
simpler.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add driver for Texas Instruments pcm3168a codec
Signed-off-by: Damien.Horsley <Damien.Horsley@imgtec.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Explicitly set the transmit data level on the transceiver to 16 samples
rather then the default 0. This matches both the level set in the vendor
kernel and the (seemingly very similar) i2s engine. This fixes audio
glitches when playing back at 192k rate.
At the same time, fix a trivial typo in the TDL mask definition
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Attempting to use this codec driver triggers a BUG() in regcache_sync()
since no cache type is set. The register map of this device is fairly
small and has few holes so a flat cache is suitable.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
These are all off by one; the playback and bypass switches are the top
two bits of the registers, which are at shifts 7 and 6 not 8 and 7.
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The condition for checking for XDAT being cleared was not correct.
Fixes: 36bcecd0a7 ("ASoC: davinci-mcasp: Correct TX start sequence")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
This is using completely the wrong mask and value when updating the
register. Since the correct values are already defined in the header,
switch to using a table with explicit constants rather than shifting the
array index.
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The previous commit removed the only use of these variables.
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If we only clear the tx/rx state when both are disabled it is not
possible to start/stop one multiple times while the other is running.
Since the two are independently controlled, treat them as such and
remove the false dependency between capture and playback.
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Alienware 17 (2015) has the same card and pin configuration of the
Alienware 15, so the same quirks must be applied.
Signed-off-by: Gabriele Martino <g.martino@gmx.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Lenovo Thinkpad T440s suffers from constant background noises, and it
seems to be a generic hardware issue on this model:
https://forums.lenovo.com/t5/ThinkPad-T400-T500-and-newer-T/T440s-speaker-noise/td-p/1339883
As the noise comes from the analog loopback path, disabling the path
is the easy workaround.
Also, the machine gives significant cracking noises at PM suspend. A
workaround found by trial-and-error is to disable the shutup callback
currently used for ALC269-variant.
This patch addresses these noise issues by introducing a new fixup
chain. Although the same workaround might be applicable to other
Thinkpad models, it's applied only to T440s (17aa:220c) in this patch,
so far, just to be safe (you chicken!). As a compromise, a new model
option string "tp440" is provided now, though, so that owners of other
Thinkpad models can test it more easily.
Bugzilla: https://bugzilla.opensuse.org/show_bug.cgi?id=958504
Reported-and-tested-by: Tim Hardeck <thardeck@suse.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When building the da7218 driver on a 64-bit architecture, we get
a harmless warning:
sound/soc/codecs/da7218.c: In function 'da7218_of_get_id':
sound/soc/codecs/da7218.c:2261:10: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
This changes the code to use uintptr_t to ensure we have an integer
type of the same size as a pointer and won't get a warning on any
architecture.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 4d50934abd ("ASoC: da7218: Add da7218 codec driver")
Signed-off-by: Mark Brown <broonie@kernel.org>
We get a warning for the imx-pcm-fiq driver when CONFIG_LPAE
is enabled on ARM, because dma_addr_t is 64-bit then:
sound/soc/fsl/imx-pcm-fiq.c: In function 'snd_imx_pcm_mmap':
sound/soc/fsl/imx-pcm-fiq.c:223:107: warning: format '%x' expects argument of type 'unsigned int', but argument 6 has type 'dma_addr_t {aka long long unsigned int}' [-Wformat=]
This changes the printk to use the correct format string for
printing a dma_addr_t.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Probing components can bring new DAI or DAI links based on the topology
info. This patch finds the unbound DAI links and bind them.
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This function will return success immediately for a bound DAI link.
No need to look for the cpu/codec DAIs again.
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
A machine driver can register the two ops.
When a DAI link is added or removed by a component's topology, the
ASoC core can call the ops to notify the machine driver for extra
intialization or destruction.
E.g. topology can create FE DAI links from a cpu DAI component, and
the machine driver may define an add_dai_link ops to set machine-specific
.init ops for the DAI link.
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Implement a dai link list for the soc card.
Add APIs to add/remove a DAI links dynamically, e.g. by topology.
And a dobj is embedded into the struct snd_soc_dai_link. Topology can
use the dobj to find the links created by it and remove them when the
topology component is unloaded.
The predefined DAI links are reserved to keep backward compatibility.
And they will also be added to the list.
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We should only add ignore suspend flag for some DAIs and not all.
This patches removes it from the DAIs where we do not support
this
It also marks the endpoints for which ignore_suspend should be
enabled
Signed-off-by: Praveen Diwakar <praveen.diwakar@intel.com>
Signed-off-by: Vunny Sodhi <vunnyx.sodhi@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some of the usecases can be marked as 'ignore_suspend' by
machine. For these on suspend we should keep audio controller
ON by saving the state and not suspending the device
For this we need to maintain a counter for these streams and be
active on suspend when such a stream is opened.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DAPM Machine map for machine was not specifying the paths
correctly.
The correct order should be:
"DMIC01 Rx" (SoC DMIC BE), connected to "DMIC AIF" (DMic Codec
AIF) and then "DMic" (DMic codec Input) connected to "SoC DMIC"
(Machine DMIC MIC Widget)
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since in Skylake we support another DAI for DMIC quad capture,
add a dailink for this as well. Also specify constrains for DMIC
FE devices and fixup for DMIC BEs
Signed-off-by: Dharageswari.R <dharageswari.r@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If a module is ON then we should read the module parameters from
DSP rather than driver cached values
Signed-off-by: Omair M Abdullah <omair.m.abdullah@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For messages which have larger payload than mailbox data, we need
to split the payload using set of messages containing mailbox
size as payload.
For sending such payload we already support LARGE_CONFIG_SET
IPCs and now to query such payload add LARGE_CONFIG_GET IPC
Signed-off-by: Mousami Jana <mousami.janax@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SKL actual mailbox size is 0x10000 and initial values were 0x800,
so update these accordingly
Signed-off-by: Omair M Abdullah <omair.m.abdullah@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Module initialization parameter data can be set by
- INIT_INSTANCE IPC by using the default value
- SET_PARAMS immediately after INIT_INSTANCE
- SET_PARAMS data from kcontrol values set
this patch add param type to identify the parameters
has to be sent to DSP.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Mic select is a DSP module which is used to select one or many
inputs to form an output. This is useful to select data
selectively from PDM input and hence the name. This module is of
generic module type.
This patch adds support to add and configure Mic select module in
firmware topology.
Signed-off-by: Dharageswari R <dharageswari.r@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
A module can require extra memory for processing, like audio
algorithms. The memory for these modules needs to be represented
in base module configuration and passed to DSP on init, so add
the memory pages as a field in widget data
Signed-off-by: Dharageswari.R <dharageswari.r@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
A module is loaded when the path consisting the module is opened.
The module binary(ies) is loaded from file system and cached in
kernel memory for future use. This is downloaded to DSP using DMA
and invoking Load module IPCs
This patch adds support for load/unload module IPCs, DMAing
modules and manging the modules
Signed-off-by: Dharageswari R <dharageswari.r@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Previously we recorded "last interrupt position" and used it in
pointer callback. This is not correct implementation, and it causes
underruns when user space monitors buffer level to decide when to
send next data chunk in low latency application.
Remove position recording in IRQ handler and also hw_ptr in
struct mtk_afe_memif used to record that, and let pointer callback
reports current HW pointer instead.
Signed-off-by: Koro Chen <koro.chen@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
L/R channel data has been treated as inverted on R-Car sound 16bit mode,
Thus, 4689032b1("ASoC: rsnd: tidyup data align position") tidyuped data
align position. But it couldn't care about capture case. This patch
cares both playback/capture
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We have two latest thinkpad laptop models which are all based on the
Intel skylake platforms, and all of them have the codec alc293 on
them. When the machines boot to the desktop, an greeting dialogue
shows up with the notification sound. But on these two models, there
is noise with the notification sound. We have 3 SKUs for each of
the models, all of them have this problem.
So far, this problem is only specific to these two thinkpad models,
we did not find this problem on the old thinkpad models with the
codec alc293 or alc292.
A workaround for this problem is disabling the aamix.
Cc: stable@vger.kernel.org
BugLink: https://bugs.launchpad.net/bugs/1523517
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
DWC IP can be powered off during system suspend in some platforms.
After system is resumed, dwc needs to be programmed again to continue
audio use case.
Signed-off-by: Maruthi Bayyavarapu <maruthi.bayyavarapu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DWC in ACP 2.x IP has different offsets for I2S_COMP_PARAM_* registers.
Added a quirk to support the same.
Signed-off-by: Maruthi Bayyavarapu <maruthi.bayyavarapu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When DW controller is in master mode, it can disable/enable clock
during the device runtime suspend/resume sequence.
Signed-off-by: Maruthi Bayyavarapu <maruthi.bayyavarapu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On the internal mic of the Packard Bell DOTS, one channel
has an inverted signal. Add a quirk to fix this up.
Cc: stable@vger.kernel.org
BugLink: https://bugs.launchpad.net/bugs/1523232
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In BXT-P A0, HD-Audio DMA requests is later than expected,
and makes an audio stream sensitive to system latencies when
24/32 bits are playing.
Adjusting threshold of DMA fifo to force the DMA request
sooner to improve latency tolerance at the expense of power.
v2: move Intel specific code to hda_intel.c
Signed-off-by: Lu, Han <han.lu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
rme96 driver needs to reset DAC depending on the sample rate, and this
results in resetting to the max volume suddenly. It's because of the
missing call of snd_rme96_apply_dac_volume().
However, calling this function right after the DAC reset still may not
work, and we need some delay before this call. Since the DAC reset
and the procedure after that are performed in the spinlock, we delay
the DAC volume restore at the end after the spinlock.
Reported-and-tested-by: Sylvain LABOISNE <maeda1@free.fr>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Both the sysclk and asyncclk members of arizona_priv are signed by we
refer to them through an unsigned pointer. This patch fixes this small
harmless error.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The core expects "const char * const" and "unsigned int" for enum
controls, various places in Arizona use "const char *" and "int".
This patch corrects the type of these arrays.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Always on widgets currently have some odd interactions with DAPM.
Enabling/disabling a widget (snd_soc_dapm_enable_pin) then connecting
it to a path works as expected, ie. when the widget is disabled the
path doesn't power up and it does when the widget is enabled. However
once in a path enabling the widget does not cause anything to power
up, dapm_widget_set_power will return the current power state of the
widget as 1, meaning we never check peer power states.
This patch updates dapm_always_on_check_power to return w->connected
such that it is effected by snd_soc_dapm_enable_pin and the like.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SSICR::SWSP bit controls WS signal low/high, but in case of TDM
it is inverted. This patch solves this issue.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds tlv bytes topology control creation and control load to
initialize kcontrol data. And this also adds the callbacks for
the these tlv byte kcontrols
Signed-off-by: Mythri P K <mythri.p.k@intel.com>
Signed-off-by: Divya Prakash <divya1.prakash@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds support to configure module parameter during module
initialization or after module init using set module param
required by the DSP firmware sequence.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some DSP modules has user configurable parameters, which are
required by some modules at module initialization.
To configure the module algorithm parameter during initialization
we add helpers here
Signed-off-by: Divya Prakash <divya1.prakash@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some DSP modules have user configurable parameters. These
parameters are required by modules in the following scenario
- during initialization
- after initialization using set parameter
This patch adds helper routine to set module parameters using
large config set IPC message and removes params to be passed as
init module routine.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On Skylake we can support upton 4DMICs on the PDM port, so update
the PCM capabilities accordingly
Also add a new DAI for DMIC pin which can be used for getting raw
DMIC data
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Dharageswari.R <dharageswari.r@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
sound/soc/codecs/da7218.c:3214:9-10: WARNING: return of 0/1 in function 'da7218_volatile_register' with return type bool
Return statements in functions returning bool should use
true/false instead of 1/0.
Generated by: scripts/coccinelle/misc/boolreturn.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As hdac->num_nodes is unsigned we can not check if
snd_hdac_get_sub_nodes() has returned error or success. Lets have a
temporary int to check the error value.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
We have been returning success even if snd_soc_card_jack_new() fails.
Lets check the return value and return error if it fails.
Fixes: 12cc6d1dca ("ASoC: tegra_alc5632: Register jacks at the card level")
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 1fb34b4836 ('ASoC: sun4i: Implement MIC1 capture') added back some
code that disregards the clk_set_rate error code and always returns
-EINVAL. Fix that and return the code in order to have more clue about
what's going on.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The comment is misleading on how we should support external power amps, and
the variable is not used and generates a warning.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When switching between two clock sources using the FLL freerun to smooth
the transition we should wait 32uS after putting the FLL into freerun
before we proceed. In practice we appear to be getting enough delay from
the surrounding code, but better to make it explicit.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds missing check of snd_soc_of_get_dai_name().
It might not be able to use sound card, because it might returns
-EPROBE_DEFER.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
drv pointer should be "base + offset" instead of
"current + offset". This patch fixup this issue, otherwise
third and subsequent pointer will be broken
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The numbers aren't always linear, just like in the real world.
Correct to the right numbers stated in the datasheet (although we
can't trust the datasheet as well).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Renesas R-Car can out TDM by
1) 6ch x 1 DAI as TDM Extend Mode
2) 2ch x 4 x 1 DAI as TDM split Mode
3) 2ch x 3 DAI or
2ch x 4 DAI as TDM Multichannel Mode
This patch adds 1) TDM Extend Mode. Because of HW design,
this 6ch data will be outputed via 8ch data width.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current DVC is assuming that the sound is always stereo.
This patch makes it more flexible
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current SSI is assuming that the sound is always stereo. But, SSI needs
to calculate its frequency when master mode. Then This frequency depends
on each SSI's slots, and TDM mode (= TDM Extend Mode, TDM split Mode,
TDM Multichannel Mode).
This patch enables to use non-stereo sound.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It will have TDM settings on SSIWSR. Actually, we would like to set
it on rsnd_ssi_config_init(), but we can't. Because SSI might be used
as clock master (It doesn't need to call rsnd_ssi_config_init() when
clock master mode).
This patch adds new ssi->wsr and set it on rsnd_ssi_start().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In order to enhance code readability, this patch adds
rsnd_ssi_config_init() and moves SSICR register settings to it.
This is prepare patch for TDM support
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SRC_BUSIF_MODE has both IN/OUT register. Current src driver sets
IN register only. This patch sets missing OUT register.
IN/OUT register are using default setting, so, there is no
HW effect.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DVC/SRC/SSIU needs ADINR::CHNUM settings too. This patch adds
these missing value.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
adg.c is used from ssi/src/cmd. Thus don't use confusable *mod here.
This patch rename it to ssi_mod/src_mod/cmd_mod
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
One of the input path used in the Allwinner codec is the MIC1. Add support
for it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There are more and more google projects need to use DMI to get the
platform data configuration. And those projects use the same
configuration. To clean those redundant code, we define a general
DMI for those projects with the same platform data configuration.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds support for DA7217 and DA7218 audio codecs.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The recent addition of ELD notifier for Intel HDMI/DP codec may lead
the bad codec connection found as kernel messages like below:
Suspending console(s) (use no_console_suspend to debug)
hdmi_present_sense: snd_hda_codec_hdmi hdaudioC0D2: HDMI status: Codec=2 Pin=6 Presence_Detect=1 ELD_Valid=1
snd_hda_intel 0000:00:1f.3: spurious response 0x0:0x2, last cmd=0x206f2e08
snd_hda_intel 0000:00:1f.3: spurious response 0x0:0x2, last cmd=0x206f2e08
....
snd_hda_codec_hdmi hdaudioC0D2: HDMI: ELD buf size is 0, force 128
snd_hda_intel 0000:00:1f.3: azx_get_response timeout, switching to polling mode: last cmd=0x206f2f00
snd_hda_intel 0000:00:1f.3: No response from codec, disabling MSI: last cmd=0x206f2f00
snd_hda_intel 0000:00:1f.3: azx_get_response timeout, switching to single_cmd mode: last cmd=0x206f2f00
azx_single_wait_for_response: 42 callbacks suppressed
This seems appearing when the sound driver went to suspend before i915
driver. Then i915 driver disables HDMI/DP audio bit and calls the
registered notifier, and the HDA codec tries to handle it as a
hot(un)plug. But since the driver is already in the suspended state,
it fails miserably.
As this is a sort of spurious wakeup, it can be ignored safely, as
long as it's delivered during the system suspend. OTOH, if a
notification comes during the runtime suspend, the situation is
different: we need to wake up. But during the system suspend, such a
notification can't be the reason for a wakeup.
This patch addresses it by a simple check of the current sound card
status. The skipped notification doesn't matter because the HDA
driver will check the plugged status forcibly at the resume in
return.
Then, why the card status, not a runtime PM status or else? The HDA
controller driver is supposed to set the card status to D3 at the
system suspend but not at the runtime suspend. So we can see it as a
flag that is set only for the system suspend. Admittedly, it's a bit
ugly, but it should work well for now.
Reported-and-tested-by: "Zhang, Xiong Y" <xiong.y.zhang@intel.com>
Fixes: 25adc137c5 ('ALSA: hda - Wake the codec up on pin/ELD notify events')
Cc: <stable@vger.kernel.org> # v4.3+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Quite a large batch of fixes have come in since the merge window, mainly
driver specific ones but there's a couple of core ones:
- A fix for DAPM resume on active streams to ensure everything ends up
cleanly in the right state.
- Reset the DAPM cache when freeing widgets to fix a crash on driver
remove and reload.
The PM functions for nau8825 are new code which fix crashes on resume.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWWE13AAoJECTWi3JdVIfQF+wH/3D0Asc5rVdU81cxaxdjgGxJ
WUGUCJ+4D1HTtZQf8MouwFqMvDK+lOKiPkAzMdyk3NQG50S0XtMD8xM7JeglPZ1L
U7ro6EfYqGmkMyqClVxWnJMBnGoTiLrAftFlIBFPaQ6FDdfMMlNcK2Y4hCs/t3y7
A5T0LlqKdz++bKQRoq0zpiWWSnfoaEub25IaEB97k9sjlr9rRTR1UwHibHdm3JGg
vzkqLTaH/zm1VgR70jH6XnQSN8KtIdrx/u2ZWJZVqfioMTMFYIboufcwDWqX4oNA
vqcYjzfCyhDaMnVYpI+7ettHfXn3iBR3VykXIOI1uzM63N5f1IK7bOwPRxiMXAA=
=CDO8
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v4.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v4.4
Quite a large batch of fixes have come in since the merge window, mainly
driver specific ones but there's a couple of core ones:
- A fix for DAPM resume on active streams to ensure everything ends up
cleanly in the right state.
- Reset the DAPM cache when freeing widgets to fix a crash on driver
remove and reload.
The PM functions for nau8825 are new code which fix crashes on resume.
rsnd_ssi_record_error() should recorde error, but it clears error too.
this patch fixes up semantic of rsnd_ssi_record_error that it records
error but doesn't clear error.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rsnd_src_error_record() should recorde error, but it clears error too.
this patch fixes up semantic of rsnd_src_error_record that it records
error but doesn't clear error.
And this patch renames
rsnd_src_error_clear() to rsnd_src_status_clear()
rsnd_src_error_record() to rsnd_src_record_error()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd driver is indicating how to use regmap debug method
on gen.c comment area.
regmap debug method indicates address and value, but rsnd driver is
using too many IPs (SSI/SSIU/SRC/CTU/MIX/DVC/CMD), and address.
Thus, we would like to know more useful information for debugging.
This patch indicates address name for debugging.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Expand the list of available firmware names to include a good selection
of generic uses for the DSP cores.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Just code refactoring, to reuse it if new DAI Links are added later
based on topology in component probing phase.
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Define soc_init_dai_link() to wrap link initialization, to reuse it later
by snd_soc_instantiate_card() when adding new DAI links from topology in
component probing phase.
Move static func snd_soc_init_multicodec(), so that it can be reused by
soc_init_dai_link(). This saves adding a function declaration for
snd_soc_init_multicodec().
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The MCPS is freed first thing in pmd events but non memory. So if
we face error during teardown we leak this mem, so move the code
up
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds polling of CLDMA stream run bit when set
to confirm the HW reports the same value.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds pcm capability to support 16/8k rates and 32 bit formats
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Module hw param fixup will change the valid bit depth based
on the fixup flag. If valid bit depth changes, need to set
the bit depth according to valid bit depth. This patch
fixes this issue of updating bit depth correctly.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
PCM prepare callbacks can be called multiple times. During S3
the stream registers will be reset when Controller is reset.
When stream is resumed, these stream registers needs to reconfigured.
This patch removes the check in prepare callback() if stream already
prepared, which will allow reconfiguring of stream registers and also
decouple stream when stream is resumed to route audio via DSP.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
After a recent cleanup, the soc_card variable became unused
and now produces a warning:
soc/sh/rcar/core.c: In function '__rsnd_kctrl_new':
soc/sh/rcar/core.c:801:23: warning: unused variable 'soc_card' [-Wunused-variable]
This removes the variable.
Fixes: 1a497983a5 ("ASoC: Change the PCM runtime array to a list")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
DAPM models various widgets but lacks a sink widget.
DSPs can have modules which take audio data, process it and are
capable of generating events thus acting as a sink of data.
To make the dapm graph complete for such paths we need a dapm
sink widget for these modules, so add a SND_SOC_DAPM_SINK to
declare such a widget. This widget will be treated as
SND_SOC_DAPM_EP_SINK endpoint in the dapm graph
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
For DAPM resume, we should first change the power state of the
card and then recheck the endpoints. This ensures the dapm is
resumed first and then userspace can resume the streams.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix kernel-doc warnings in soc-ops.c:
..//sound/soc/soc-ops.c:415: warning: No description found for parameter 'ucontrol'
..//sound/soc/soc-ops.c:415: warning: Excess function parameter 'uinfo' description in 'snd_soc_put_volsw_sx'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Previously, the iec958 channels status sampling freq was set only if not
already set. It means that it is not updated for next PCM sessions.
With this patch, we ensure the iec958 channels status sampling freq is set
to the runtime rate for each PCM session.
Signed-off-by: Moise Gergaud <moise.gergaud@st.com>
Acked-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ASRC need to enable the spba clock, when sdma is using share peripheral
script. In this case, there is two spba master port is used, if don't
enable the clock, the spba bus will have arbitration issue, which may
cause read/write wrong data from/to ASRC registers
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SPDIF need to enable the spba clock, when sdma is using share peripheral
script. In this case, there is two spba master port is used, if don't
enable the clock, the spba bus will have arbitration issue, which may
cause read/write wrong data from/to SPDIF registers.
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ESAI need to enable the spba clock, when sdma is using share peripheral
script. In this case, there is two spba master port is used, if don't
enable the clock, the spba bus will have arbitration issue, which may
cause read/write wrong data from/to ESAI registers.
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
using params_width function to simplify code.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add tdm slots operation support. If tdm slots and slot width have
been configured in machine driver, we should use these values.
Otherwise, using relevant channels and word length to set slots
and slot width.
SAI will generate BCLK depends on sample rate, slots and slot width.
And there may be unused BCLK cycles before each LRCLK transition.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add platform specific data for Terra project.
Signed-off-by: Luke_Yin@asus.com <Luke_Yin@asus.com>
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Correct valid data word register value for 24 bit data width. The
bit value should be 10 (aka 0x2), not 0x10.
This fixes playback of 24 bit audio.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The previous commit ef3e199a49 ("ASoC: Intel: sst: only use
sst-firmware when DW DMAC is available") does not fix the 0day
building errors thoroughly:
sound/built-in.o: In function 'dw_dma_remove'
sound/built-in.o: In function 'dw_dma_probe'
Here we fallback to select sst-firmware only when DW DMAC
is built-in selected. We may need to refactor sst common
driver and split DW related codes to platform driver, but
ATM, this fallback may be the smallest fix.
Please be noticed that after applying this patch, we may
need select DW DMAC manually in DMA driver menu, before
we can prompt and select HSW/BDW and old BYT machines.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
A new randconfig build failure shows that the fsl-asoc-card module
must not be built-in when the AC97 driver is a loadable module:
sound/built-in.o: In function `fsl_asoc_card_late_probe':
:(.text+0x571d8): undefined reference to `snd_ac97_update_bits'
I couldn't come up with a nice solution, so this adds another dependency
on "X || !X", which is the Kconfig way of saying that we have an
optional dependency on something that might be a loadable module.
Fixes: 50760cad9d ("ASoC: fsl-asoc-card: add AC'97 support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Gigabyte Z710X mobo with ALC1150 codec gets significant noises from
the analog loopback routes even if their inputs are all muted.
Simply kill the aamix for fixing it.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=108301
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We have a machine Dell XPS 13 with the codec alc256, after resume back
from S3, the headphone has noise when play sound.
Through comparing with the coeff vaule before and after S3, we found
restoring a coeff register will help remove noise.
BugLink: https://bugs.launchpad.net/bugs/1519168
Cc: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
kzalloc() can return NULL if it fails, and then we will be dereferencing
a NULL pointer.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
sound/soc/codecs/inno_rk3036.c:480:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
RK3036 SoC integrated with an Inno audio codec.
This driver implements the functions of it.
There is not need a special machine driver, since the
simple-card machine driver works perfect in this case.
Signed-off-by: ZhengShunQian <zhengsq@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We have requested the firmware but missed releasing it.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
When McASP is used as TX/RX synchronous (TX side generating clocks for RX
side also) and only capture is used we need to configure the number of TX
slots in order McASP to be able to generate the Frame sync.
Fixes: 9273de1940d9e ("ASoC: davinci-mcasp: Add set_tdm_slots() support")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since driver use infoframe symbols from video/hdmi.c we should select this
symbol for this driver
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Skylake driver uses snd_dma_buffer for data and buffer, these are variables
and not pointer so do not test field addresses.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the component framework to keep the display on till the
playback in progress.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch uses hdmi framework in video to fill audio infoframe.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DAI ops are used for triggering HDMI streams and configuring
the parameters
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Power up/down the AFG node during runtime resume/suspend.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds HDA based HDMI driver to be used in platforms like SKL
and onwards
Register the hdmi driver with hda bus and register dais.
Also parse the widget and initialize identified pin and converter
widgets.
For simplification, currently only one pin and one converter
widget are enabled on board, as well as limit the rates supported
to simples ones and not based on ELD. This things will come
eventually once basic support for this is merged
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
"data" is always NULL in this function. I think we should be passing
"&data" to sst_prepare_and_post_msg() instead of "data".
Fixes: 3d9ff34622 ('ASoC: Intel: sst: add stream operations')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Tested-by: Dinesh Mirche <dinesh.mirche@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As we are now passing the filter data as pointers to the drivers,
we can take the final step and also pass the filter function the
same way. I'm keeping this change separate, as there it's less
obvious that this is a net win.
Upsides of this are:
- The ASoC drivers are completely independent from the DMA engine
implementation, which simplifies the Kconfig logic and in theory
allows the same sound drivers to be built in a kernel that supports
different kinds of dmaengine drivers.
- Consistency with other subsystems and drivers
On the other hand, we have a few downsides:
- The s3c24xx-dma driver now needs to be built-in for the ac97 platform
device to be instantiated on s3c2440.
- samsung_dmaengine_pcm_config cannot be marked 'const' any more
because the filter function pointer needs to be set at runtime.
This is safe as long we don't have multiple different DMA engines
in thet same system at runtime, but is nonetheless ugly.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As this driver can now be compiled for ARM64, we get a new warning
as a result of passing a DMA filter data pointer through an 'int':
sound/soc/sh/fsi.c: In function 'fsi_dma_probe':
sound/soc/sh/fsi.c:1372:24: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
shdma_chan_filter, (void *)io->dma_id,
We already know that we only need the legacy filter function on
arch/sh, so we can hide the legacy DMA interface function
behind an #ifdef. This has the other advantage of no longer
depending on the shdma_chan_filter function to be visible.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is a little endian device, but so far we've been relying on
the regmap mmio bus handling this for us without explicitly
stating that fact. After commit 4a98da2164cf (regmap-mmio: Use
native endianness for read/write, 2015-10-29), the regmap mmio
bus will read/write with the __raw_*() IO accessors, instead of
using the readl/writel() APIs that do proper byte swapping for
little endian devices.
So if we're running on a big endian processor and haven't
specified the endianness explicitly in the regmap config or in
DT, we're going to switch from doing little endian byte swapping
to big endian accesses without byte swapping, leading to some
confusing results. Specify the endianness explicitly so that the
regmap core properly byte swaps the accesses for us.
Cc: Kenneth Westfield <kwestfie@codeaurora.org>
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Tyler Baker <tyler.baker@linaro.org>
Cc: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
sound card rtd was an array and was updated to a list so update
the driver to use a list
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
sound card rtd was an array and was updated to a list so update
the driver to use a list
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
64bit compiler indicates this without this patch
linux/sound/soc/sh/rcar/core.c: In function 'rsnd_probe':
linux/sound/soc/sh/rcar/core.c:1002:16: warning: cast from pointer to\
integer of different size [-Wpointer-to-int-cast]
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
a3af0c65("ASoC: ak4613: add single-end optional property for IN/OUT pins")
added IN/OUT pin single-end optional property, but it used "ak4613" as
vendor prefix. This patch fixup to asahi-kasei.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The new optimized do_div implementation (now in asm-generic/next) exposes a
glitch in the brownstone audio driver by producing a compile-time warning:
sound/soc/pxa/brownstone.c: In function 'brownstone_wm8994_hw_params':
sound/soc/pxa/brownstone.c:67:85: warning: comparison of distinct pointer types lacks a cast
sound/soc/pxa/brownstone.c:67:10125: warning: right shift count >= width of type [-Wshift-count-overflow]
sound/soc/pxa/brownstone.c:67:10254: warning: passing argument 1 of '__div64_32' from incompatible pointer type [-Wincompatible-pointer-types]
The driver just divides two plain integer values, so it should not
use do_div to start with, but has apparently done so ever since the
code was first merged. This replaces do_div with a simple division
operator.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
