dtc recently added PCI bus checks. Fix these warnings.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Russell King <linux@armlinux.org.uk>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* Use newly added Gen-3 fallback compat string
This is consistent with ongoing efforts to use per-generation
fallback strings where appropriate across devices found
on R-Car SoCs. The aim of the effort being to strike a balance
between the limited information available about the compatibility
of devices found on different SoCs and the desire to ease enabling
devices on new SoCs.
This has no run-time effect due to the presence of a per-SoC
compat string.
* Enable second CPU core on RZ/G1M (r8a7743)
The RZ/G1M has two CA15 cores running at up to 1.5GHz
* Enable frequency scaling on RZ/G1M (r8a7743)
* Add six I2C cores to RZ/G1M (r8a7743) SoC DT
This is a step towards enabling these cores on boards that use this SoC
* Add CEC clock for HDMI transmitter to R-Car M2-W (r8a7791) Koelsch
Hans Verkuil says "The adv7511 on the Koelsch board has a 12 MHz fixed
clock for the CEC block. Specify this in the dts to enable CEC support."
* Add PFC support to RZ/G1E (r8a7745) SoC and add Ethernet and SCIF2
pins to SK-RZG1E board.
This allows the kernel to control multiplexed pins for Ethernet
and SCIF2 rather than relying on setup inherited at boot.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=G9vX
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt2-for-v4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Pull "Second Round of Renesas ARM Based SoC DT Updates for v4.14" from Simon Horman:
* Use newly added Gen-3 fallback compat string
This is consistent with ongoing efforts to use per-generation
fallback strings where appropriate across devices found
on R-Car SoCs. The aim of the effort being to strike a balance
between the limited information available about the compatibility
of devices found on different SoCs and the desire to ease enabling
devices on new SoCs.
This has no run-time effect due to the presence of a per-SoC
compat string.
* Enable second CPU core on RZ/G1M (r8a7743)
The RZ/G1M has two CA15 cores running at up to 1.5GHz
* Enable frequency scaling on RZ/G1M (r8a7743)
* Add six I2C cores to RZ/G1M (r8a7743) SoC DT
This is a step towards enabling these cores on boards that use this SoC
* Add CEC clock for HDMI transmitter to R-Car M2-W (r8a7791) Koelsch
Hans Verkuil says "The adv7511 on the Koelsch board has a 12 MHz fixed
clock for the CEC block. Specify this in the dts to enable CEC support."
* Add PFC support to RZ/G1E (r8a7745) SoC and add Ethernet and SCIF2
pins to SK-RZG1E board.
This allows the kernel to control multiplexed pins for Ethernet
and SCIF2 rather than relying on setup inherited at boot.
* tag 'renesas-dt2-for-v4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: dts: r8a7791: Use R-Car SATA Gen2 fallback compat string
ARM: dts: r8a7790: Use R-Car SATA Gen2 fallback compat string
ARM: dts: r8a7743: Add OPP table for frequency scaling
ARM: dts: r8a7743: Add APMU node and second CPU core
ARM: dts: koelsch: Add CEC clock for HDMI transmitter
ARM: dts: sk-rzg1e: add Ether pins
ARM: dts: sk-rzg1e: add SCIF2 pins
ARM: dts: r8a7745: add PFC support
ARM: dts: r8a7743: Add I2C DT support
One fix for Tegra124 to hook the host1x device up with the SMMU.
The remainder of this enables USB device mode on a couple of boards
where the port is currently unused.
-----BEGIN PGP SIGNATURE-----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=0VoF
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.14-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt
Pull "ARM: tegra: Device tree changes for v4.14-rc1" from Thierry Reding:
One fix for Tegra124 to hook the host1x device up with the SMMU.
The remainder of this enables USB device mode on a couple of boards
where the port is currently unused.
* tag 'tegra-for-4.14-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: Enable UDC on AC100
ARM: tegra: Enable UDC on Jetson TK1
ARM: tegra: Enable UDC on Dalmore
ARM: tegra: Enable UDC on Beaver
ARM: tegra: Register host1x node with IOMMU binding on Tegra124
- A clean up patch from Shawn Lin to remove the deprecated dwmmc
property 'num-slots'.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZloxmAAoJEFBXWFqHsHzOmiYH/3dBPc18iMgsEjHJ73FUJCb8
RvIxN/o4W60Kokm+vsrNHx3LfZYUCfgQCeHlYCHpL1jFGpwD0DBxNQ9QlMDG+TCa
IN+c32aB0a0U0RHl+c5jKLqPy4eVvD4NNDWGVpwjSpK/MARrsKjhEwr/Yjcrj87c
+miIiXBmTsUhzwXQF1UkK719rXI7tgZQNqO06qxJN0QxwKajZPyZzRbe1kgI1xQK
k7F8WG3OGxyRJYRt/qnovnCv7lDX1Jk4S0ySqhocEyyqkqUOXElRARWZOyP3D8CY
wJQIHRzlM/ffqDpbQDa17YuGmnMgsHZ/+Fa8tHvdL353Ow0TM6KkjoRGTd8F4GI=
=WoGP
-----END PGP SIGNATURE-----
Merge tag 'zte-dt-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
Pull "ZTE device tree updates for 4.14" from Shawn Guo:
- A clean up patch from Shawn Lin to remove the deprecated dwmmc
property 'num-slots'.
* tag 'zte-dt-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: zte: remove num-slots from zx296702-ad1
- A series from Andrew Lunn updating imx6-rdu2 board to enable
on-board Marvell switch support.
- A series from Jagan Teki updating imx6ul-isiot and imx6ul-geam to
enable audio card and FEC support.
- Add support for Toradex Ixora V1.1 and Apalis Evaluation Board
along with some cleanups.
- Enable DRM display support for imx6ul-evk and imx7d-sdb board.
- Add i.MX53 based Beckhoff CX9020 board support.
- Add GPMI NAND and APBH DMA devices for i.MX7 and enables NAND support
for imx7-colibri board.
- Enables the ADV7180 analog video decoder sensor connected to the
IMX6 IPU on various Gateworks Ventana boards.
- Minor updates on misc boards and some random cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZloV7AAoJEFBXWFqHsHzOeIAH/ieM8fZEeUHO9waD4aoQJulp
kQHbJFKlEaQrB/y9LVUmNae0w/dpOaf5k/NVtfLQAZQhMqN6Y9XFQA0fnUAgiNbs
fknQpL6VnrO7nGUDEbIUommrRDPEVN9SEiiPpLpD938QjUDxTAibb8++QQOHC/S6
NLQbYMvubDTaUXkOiRodLQU6U/RQ5Byzmu+ytuKjlB1la0OzMegebD/OMXZtgysx
hcEDVBIEZmQO1TPrl5p6IZjjdHs1ua4gfRLQWq1RPXECakHJuyCPKILibyRID15j
w0C+sTxP1uIN950VYzufrbLIdyheWHSrx0FZSWa7tnus8W+h8kBAUd6NxyHLiyU=
=0Cwx
-----END PGP SIGNATURE-----
Merge tag 'imx-dt-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
Pull "i.MX device tree updates for 4.14" from Shawn Guo:
- A series from Andrew Lunn updating imx6-rdu2 board to enable
on-board Marvell switch support.
- A series from Jagan Teki updating imx6ul-isiot and imx6ul-geam to
enable audio card and FEC support.
- Add support for Toradex Ixora V1.1 and Apalis Evaluation Board
along with some cleanups.
- Enable DRM display support for imx6ul-evk and imx7d-sdb board.
- Add i.MX53 based Beckhoff CX9020 board support.
- Add GPMI NAND and APBH DMA devices for i.MX7 and enables NAND support
for imx7-colibri board.
- Enables the ADV7180 analog video decoder sensor connected to the
IMX6 IPU on various Gateworks Ventana boards.
- Minor updates on misc boards and some random cleanups.
* tag 'imx-dt-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (47 commits)
ARM: dts: imx6q-bx50v3: Enable i2c recovery mechanism
ARM: dts: imx6q-apalis-eval: add support for Apalis Evaluation Board
ARM: dts: imx6: add support for Toradex Ixora V1.1 carrier board
ARM: dts: imx6qdl-apalis: imx6q-apalis-ixora: use i2c from dwc hdmi
ARM: dts: imx6q-apalis-ixora: add camera i2c bus definition
ARM: dts: imx6q-apalis-ixora: get rid of obsolete fusion comment
ARM: dts: imx6qdl-apalis: reword cam i2c comment
ARM: dts: imx6qdl-apalis: imx6q-apalis-ixora: get rid of tegra legacy gen1_i2c comment
ARM: dts: imx6q-apalis-ixora: combine aliases
ARM: dts: imx6qdl-apalis: split usdhc1 pinctrl to support 4- and 8-bit
ARM: dts: imx6q-apalis-ixora: fix usdhc2 pinctrl property
ARM: dts: imx6ul-liteboard: Support poweroff
ARM: dts: imx: add CX9020 Embedded PC device tree
ARM: dts: imx53: add alternative UART2 configuration
ARM: dts: imx53: add srtc node
dt-bindings: arm: Add entry for Beckhoff CX9020
ARM: dts: i.MX25: add RNGB node to dtsi
ARM: dts: imx6ul-14x14-evk: Remove unrelated pin from ENET group
ARM: dts: imx7d-sdb: Add flexcan support
ARM: dts: imx7-colibri: add NAND support
...
4.14, please pull the following:
- Eric moves the bcm2837 DT file from arm64 to arm because it created a maintenance
problem and would have required either duplication or cross merges
- Stefan changes how the pinmuxing is defined and pushes it at the board level
to support Raspberry Pi Zero Wireless. He then adds supports for the actual
Raspberry Pi Zero Wireless board along with binding documentation. Stefan
also defines a proper SMP enable-method property and binding for BCM2836
(Raspbery Pi 2)
- Rafal describes the BCM5301X USB ports correctly in Device Tree such that
it becomes possible to assign them to specific LED triggers (e.g: USB activity).
He does the same thing for BCM53573 and defines default LED triggers for USB.
- Jon provides a fix for Northstar Plus which consists in correctly defining
the "dma-coherent" property for peripherals which are DMA coherent. He also
does a bit of re-arrangement of the USB DT nodes and finally adds USB 3 PHY
and host controller support for NorthStar Plus
- Florian adds support for Broadcom's BCM947189ACDBMR reference board which is
based on BCM47182/53573 and which supports external MoCA (BCM6802)
- Ray fixes the wrong UART2 base address for Cygnus
- Scott moves the v3d node in the proper unit address order and defines the correct
UART alias for the BCM91130_entphn reference board to be UART3
- Jason adds the DT node for the Cygnus Cortex-A9 Performance Monitoring Unit
- Jonathan adds a bunch of additional peripherals to the Cygnus DTS include file:
SDHCI, Keypad, SPI, DMA and pinmux configurations
- Raveendra adds the Cygnus OHCI and EHCI Device Tree nodes
-----BEGIN PGP SIGNATURE-----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=WUr3
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.14/devicetree' of http://github.com/Broadcom/stblinux into next/dt
Pull "Broadcom devicetree changes for 4.14" from Florian Fainelli:
This pull request contains Broadcom ARM-based SoCs Device Tree changes for
4.14, please pull the following:
- Eric moves the bcm2837 DT file from arm64 to arm because it created a maintenance
problem and would have required either duplication or cross merges
- Stefan changes how the pinmuxing is defined and pushes it at the board level
to support Raspberry Pi Zero Wireless. He then adds supports for the actual
Raspberry Pi Zero Wireless board along with binding documentation. Stefan
also defines a proper SMP enable-method property and binding for BCM2836
(Raspbery Pi 2)
- Rafal describes the BCM5301X USB ports correctly in Device Tree such that
it becomes possible to assign them to specific LED triggers (e.g: USB activity).
He does the same thing for BCM53573 and defines default LED triggers for USB.
- Jon provides a fix for Northstar Plus which consists in correctly defining
the "dma-coherent" property for peripherals which are DMA coherent. He also
does a bit of re-arrangement of the USB DT nodes and finally adds USB 3 PHY
and host controller support for NorthStar Plus
- Florian adds support for Broadcom's BCM947189ACDBMR reference board which is
based on BCM47182/53573 and which supports external MoCA (BCM6802)
- Ray fixes the wrong UART2 base address for Cygnus
- Scott moves the v3d node in the proper unit address order and defines the correct
UART alias for the BCM91130_entphn reference board to be UART3
- Jason adds the DT node for the Cygnus Cortex-A9 Performance Monitoring Unit
- Jonathan adds a bunch of additional peripherals to the Cygnus DTS include file:
SDHCI, Keypad, SPI, DMA and pinmux configurations
- Raveendra adds the Cygnus OHCI and EHCI Device Tree nodes
* tag 'arm-soc/for-4.14/devicetree' of http://github.com/Broadcom/stblinux:
ARM: BCM53573: Specify ports for USB LED for Tenda AC9
ARM: dts: cygnus: Add generic-ehci/ohci nodes
ARM: dts: cygnus: add serial0 alias for uart3 on bcm91130_entphn
ARM: dts: cygnus: Add additional peripherals to dtsi
ARM: dts: cygnus: Enable Performance Monitoring Unit
ARM: dts: cygnus: place v3d in proper address ordered location
ARM: dts: cygnus: Fix incorrect UART2 register base
ARM: dts: bcm283x: Add 32-bit enable method for SMP
dt-bindings: arm: add SMP enable-method for BCM2836
ARM: dts: BCM53573: Add Broadcom BCM947189ACDBMR board support
ARM: dts: BCM5301X: Specify USB ports for USB LEDs of few devices
ARM: dts: NSP: Add USB3 and USB3 PHY to NSP
ARM: dts: NSP: Rearrage USB entries
ARM: dts: NSP: Add dma-coherent to relevant DT entries
ARM: dts: bcm2835: Add Raspberry Pi Zero W
dt-bindings: bcm: Add Raspberry Pi Zero W
ARM: bcm283x: Define UART pinmuxing on board level
ARM: dts: BCM5301X: Specify USB ports for each controller
ARM: dts: bcm283x: Move the BCM2837 DT contents from arm64 to arm.
These got delayed a bit because the iodelay changes had to be
reworked for a missing Signed-off-by. And the beagleboard-x15
wants to use iodelay too for mmc:
- A series of changes to add dra7 iodelay data used for mmc
- Add support for new beagleBoard-x15 revision c
- Fix logicpd-torpedo-37xx-devkit mmc card detect direction
-----BEGIN PGP SIGNATURE-----
iQJFBAABCAAvFiEEkgNvrZJU/QSQYIcQG9Q+yVyrpXMFAlmV0+MRHHRvbnlAYXRv
bWlkZS5jb20ACgkQG9Q+yVyrpXO5lw//aPYIMinp6aR2pGlbnlzN9RksduXwKVgY
NwtXFTBZQc8c/7IbqSn2vn/VduEw+OfnGIcV/B49TlxBpi8yWFuDkCNM95Ob1zeZ
Mj/MLuUOIFV7NWimeFQc1qSHDRQO3y4HIVzKHLeiK85V8WsTPcfNRsUz5NeW3YmB
72Acl/nCCwV4imtzW9dsTd2pXngw+ZqckHq3T/SZhz6fTolSGvlGd20qGfQ3kIZ5
BgL6Ykl7WHcsUvus/ee/71QVdgLNqrEdUJKoQSMiIA6KBwuL3idYNEAGabRJA9fV
TH0FS9Jd/b+ph4gUiWRQIhlKQe2N91pdDA37ahlOijoXdL30TiW1W5EfTg+ucd/G
L5hVNNJXPxyBqLMruy4ejiwddXbBlRZ7vyDQULNYk3+c87zIGgo+b4rVtZTxCHim
xRIizeQJHm86Jk/UxdEs+m3LeTGOpkCglvZuIinju1DHyUVn4AoJR98p1rNTs1y0
+oZCZwTcx4QodncfFxUidPczzRojsUpue+8luC2EI3q0G4ATdPj8sgFzpDyZYMDQ
8docf2rfQVT3vRAGR+HM+q6rsZHErnqBMsm6hMQzA50bo5Wqm/5VYgj+FbUZ/YqQ
dl73PSrH8Uhm0MqQDzp1j3HjFV01ENfgMrbSZ/Wnj23JKF9z2EPqqKpUvQ95Fjf+
BgPLlSF68aQ=
=R16f
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.14/dt-v3-pt2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Pull "device tree changes for omaps for v4.14, part2" from Tony Lindgren:
Second set of device tree changes for omaps for v4.14 merge window.
These got delayed a bit because the iodelay changes had to be
reworked for a missing Signed-off-by. And the beagleboard-x15
wants to use iodelay too for mmc:
- A series of changes to add dra7 iodelay data used for mmc
- Add support for new beagleBoard-x15 revision c
- Fix logicpd-torpedo-37xx-devkit mmc card detect direction
* tag 'omap-for-v4.14/dt-v3-pt2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap3: logicpd-torpedo-37xx-devkit: Fix MMC1 cd-gpio
ARM: dts: am57xx-beagle-x15: Add support for rev C
ARM: dts: dra71-evm: Add pinmux configuration for MMC
ARM: dts: dra72-evm-revc: Add pinmux configuration for MMC
ARM: dts: dra72-evm: Add pinmux configuration for MMC
ARM: dts: am572x-idk: Add pinmux configuration for MMC
ARM: dts: am571x-idk: Add pinmux configuration for MMC
ARM: dts: am57xx-idk: Move common MMC/SD properties to common file
ARM: dts: am57xx-beagle-x15: Add pinmux configuration for MMC
ARM: dts: dra7-evm: Add pinmux configuration for MMC
ARM: dts: dra74x: Create a common file with MMC/SD IOdelay data
ARM: dts: dra72x: Create a common file with MMC/SD IOdelay data
This uses trigger-sources documented in commit 80dc6e1cd8 ("dt-bindings:
leds: document new trigger-sources property") to specify USB ports. Such an
information can be used by operating system to setup LEDs behavior.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Use serial0 alias to select stdout-path on Cygnus bcm911360_entphon
board.
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add PMU capability to Cygnus so trace and performance profiling
can be used.
Signed-off-by: Jason Uy <jason.uy@broadcom.com>
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Fixes commit 687c276761 ("ARM: dts: Add minimal support for LogicPD
Torpedo DM3730 devkit")
This patch corrects an issue where the cd-gpios was improperly setup
using IRQ_TYPE_LEVEL_LOW instead of GPIO_ACTIVE_LOW.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Latest update to the BeagleBoard-X15 platform (revision C). This board contains
a silicon update (Rev 2.0), which includes a fix for the 2nd ethernet phy when
running at 1000 Mbps speeds.
This board can be indentified by the [C.00] after [BBRDX15_] in the at24 eeprom:
[BBRDX15_C.001731PX150249]
Rev C is now in full production and boards are available for end users.
https://beagleboard.org/x15https://github.com/beagleboard/beagleboard-x15/
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
CC: Tony Lindgren <tony@atomide.com>
CC: Nishanth Menon <nm@ti.com>
CC: Lokesh Vutla <lokeshvutla@ti.com>
CC: Kishon Vijay Abraham I <kishon@ti.com>
CC: Jason Kridner <jkridner@beagleboard.org>
CC: Drew Fustini <drew@beagleboard.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Override the compatible string of the first USB controller to enable
device mode.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Marc Dietrich <marvin24@gmx.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Override the compatible string of the first USB controller to enable
device mode.
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Override the compatible string of the first USB controller to enable
device mode.
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use newly added R-Car SATA Gen2 fallback compat string
in the DT of the r8a7791 SoC.
This should have no run-time effect as the driver matches against
the per-SoC compat string before the fallback compat string is considered.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Use newly added R-Car SATA Gen2 fallback compat string
in the DT of the r8a7790 SoC.
This should have no run-time effect as the driver matches against
the per-SoC compat string before the fallback compat string is considered.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
- update clock controler for use as reset controller
- misc. updates/fixups/improvements
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=MUvI
-----END PGP SIGNATURE-----
Merge tag 'amlogic-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into next/dt
Pull "Amlogic 32-bit DT changes for v4.14" from Kevin Hilman:
- update clock controler for use as reset controller
- misc. updates/fixups/improvements
* tag 'amlogic-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
ARM: dts: meson6: use stable UART bindings
ARM: dts: meson: mark the clock controller also as reset controller
ARM: dts: meson: add a node which describes the SRAM
ARM: dts: meson8b: use the existing wdt node to override the compatible
ARM: dts: meson8: add the PWM controller nodes
ARM: dts: move the pwm_ab and pwm_cd nodes to meson.dtsi
Add needed information inside CPU0 for the generic cpufreq-cpu0 driver.
- clock-latency = 300 us
Approximate worst-case latency to do clock transition for every
OPPs. Using an arbitrary safe value similar to r8a7791(R-Car M2) Soc.
- operating-points = < kHz - uV >
List of 6 operating points. All of them are using the same voltage
since DVS is not supported in RZ/G1 Soc.
Note:This also fixes the below errors seen on kernel logs
[ 0.876877] cpu cpu0: dev_pm_opp_get_opp_count: OPP table not found (-19)
[ 0.883727] cpu cpu1: cpufreq_init: failed to get clk: -2
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add DT nodes for the Advanced Power Management Unit (APMU) and the
second CPU core. Use the enable-method to point out that the APMU
should be used for SMP support.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The adv7511 on the Koelsch board has a 12 MHz fixed clock
for the CEC block. Specify this in the dts to enable CEC support.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
- A series of changes for dra7 and am572 to use generic
MMC vqmmc regulator
- Clean-up tps65217 internal interrupts to define them
only in tps65217.dtsi
- Add dra7 iodelay pinctrl driver configuration
- Add buzzer support for am437x-gp-evm
- Disable HDMI CEC internal pull-ups as it seems that
all boards have an external pull for these
- Remove unnecessary interrupt-parent for omap3
- Configure droid 4 vaudio regulator initial mode and
add vibrator
- Enable NAND dma prefetch for am335x-evm, am437x and dra7
- Add pcie1 dt node for EP mode for am57x and dra7
- Add support for new dra76x SoCs and dra76x-evm
-----BEGIN PGP SIGNATURE-----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=zikX
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.14/dt-v3-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Pull "Device tree changes for omaps for v4.14 merge window" from Tony Lindgren:
- A series of changes for dra7 and am572 to use generic
MMC vqmmc regulator
- Clean-up tps65217 internal interrupts to define them
only in tps65217.dtsi
- Add dra7 iodelay pinctrl driver configuration
- Add buzzer support for am437x-gp-evm
- Disable HDMI CEC internal pull-ups as it seems that
all boards have an external pull for these
- Remove unnecessary interrupt-parent for omap3
- Configure droid 4 vaudio regulator initial mode and
add vibrator
- Enable NAND dma prefetch for am335x-evm, am437x and dra7
- Add pcie1 dt node for EP mode for am57x and dra7
- Add support for new dra76x SoCs and dra76x-evm
* tag 'omap-for-v4.14/dt-v3-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (25 commits)
ARM: dts: nokia n900: update dts with camera support
ARM: dts: Add support for dra76-evm
ARM: dts: Add support for dra76x family of devices
ARM: dts: DRA7: Add pcie1 dt node for EP mode
ARM: dts: am335x: add support for Moxa UC-8100-ME-T open platform
ARM: dts: dra7xx: Enable NAND dma prefetch by default
ARM: dts: am437xx: Enable NAND dma prefetch by default
ARM: dts: am335x-evm: Enable NAND dma prefetch by default
ARM: dts: omap4-droid4: Add vibrator
ARM: dts: motorola-cpcap-mapphone: set initial mode for vaudio
ARM: dts: omap3: Remove needless interrupt-parent property
ARM: dts: Disable HDMI CEC internal pull-ups
ARM: dts: am437x-gp-evm: Add support for buzzer
ARM: dts: Add dra7 iodelay configuration
ARM: dts: tps65217: Add power button interrupt to the common tps65217.dtsi file
ARM: dts: tps65217: Add charger interrupts to the common tps65217.dtsi file
ARM: dts: omap*: Replace deprecated "vmmc_aux" with "vqmmc"
ARM: dts: am572x-idk: Fix GPIO polarity for MMC1 card detect
ARM: dts: am571x-idk: Fix GPIO polarity for MMC1 card detect
ARM: dts: dra7: Add "max-frequency" property to MMC dt nodes
...
Add arm_global_timer node on Armada 38x
Fix PCI bus dtc warnings on mvebu 32 bits device tree files
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlmNhZUACgkQCwYYjhRyO9VwCACgpK2SLzw3pfmFMpaRZqPf7yqQ
eVoAmwf/qVDF+pPs8GIzyxyBJP7C27SR
=9oc8
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt-4.14-1' of git://git.infradead.org/linux-mvebu into next/dt
Pull "mvebu dt for 4.14 (part 1)" from Gregory CLEMENT:
Add arm_global_timer node on Armada 38x
Fix PCI bus dtc warnings on mvebu 32 bits device tree files
* tag 'mvebu-dt-4.14-1' of git://git.infradead.org/linux-mvebu:
ARM: dts: armada-38x: Add arm_global_timer node
ARM: dts: marvell: fix PCI bus dtc warnings
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJZiayzAAoJEEEQszewGV1zqQoQAIaywuQGNO/nugEzQiUSdTte
s8prIJOGZBHB9bqpWZt+R1C7euVZ6qSV7lKhacHBStJsT2Ev2w3/4VtDNODFEP6X
0IpfeqEZT+AIrDerZFQL/T6hNciT8QqNATrrCAj64XdmvFY7UJutVqF8anJid6Zv
y0pJ+n4sS41UnW60PCH9O0TPVnc7fZyzh6d5kqzs3vH96jxnIWokYsTipuH9wW2/
76RWyzjGv5Kb9iFAe9qWop2JamfWsPvqrHJjy6pJzv9RKPKi7eWHuruMg6lCqMJb
pAOuIDWNRjPK/JxyxUNGOoz3jBqM0J3xoyOnBBXa/rlBbMk0+TcwcoNjlxyxPMjD
pyCHF1iUakqKqTdQI7My3CsxiZUqPqycNVgW5P95z/jg6FUMxOMdK2Y4uRLi5luh
rOLIkjjZVcDE1VFytB4yiaiiCcqeKwHw70C6p2xL7IT8ZyfWwHMKbis9NFfEoST0
orrgh+wI9y7v2W3pxs8jj2DRwNSTcohXaruxEnBbRX5rrUQSD45hKQHt4IvbUPfo
NwFxIqrydQXsK6ARuRr1euyIZ3EpOx4JVJsa+zE5W8UO8YzAhWRG2vJx8NbSCijy
W0Ji2gWtxCPjDj4kppxb04S0Tz+/hdkA979/4ctxu2iWAMvJyb+K9+L7IiYN1cUt
p/lV2/P8A/lxQ2YMU8qe
=SWBN
-----END PGP SIGNATURE-----
Merge tag 'gemini-dts-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into next/dt
Pull "Gemini DTS updates for ARM SoC take one" from Linus Walleij:
* tag 'gemini-dts-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: dts: gemini: add pin control set-up for the SoC
ARM: dts: Add DTS file for D-Link DIR-685
ARM: dts: gemini: Switch to using macros
nodes. The rv1108 gains support for sd-cards on the evaluation board and
the general nodes get a bit of cosmetic. On rk3288 the evb gains support
saradc and the adc-key connected to it while some more boards also get
their mali gpu enabled (fennec, evb, tinker).
The biggest set of changes can be found on the rk3228/rk3229 combo this
time. It gets core support for efuse, sdmmc, sdio, io-domans and spdif
as well as a separate rk3229.dtsi that will keep the slight differences
between the two brothers rk3228/rk3229. The evaluation board also gets
some attention and abled nodes (regulators, io-domains, emmc, tsadc keys)
But I think the most interesting change is the cpu enable-method for it.
Instead of using the older in-kernel method, we're now also moving to
handling this in firmware via the psci interface on 32bit Rockchip socs.
In a recently merged pull request [0] support for the rk3228/rk3229 was
added to OP-TEE including the psci support and it seems supporting other
32bit Rockchip socs that way is also planned for the future.
[0] https://github.com/OP-TEE/optee_os/pull/1666
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAlmERL4QHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgbNLB/9Sgm6PAZtdObqta1nEjvp/5XFLlRTUuUFv
OSC0us+/22buKByODPBjnZonPUgxH95/7apaAoj+Deevms39C55nNS05GBa4sF5O
dRz1I5ZBl8LshZXs/IpS8+SjMs5zmtJfeWHw6NImqQzusXpkfoP3C9/ZDMw9XfCn
sE8Yi2EPlZAOlzI9Jqq9t1669JOQIjiDNFC6SvI9DZU37pb8olkBXMxt2VjT8Nb9
KJtpnVFFY4lisjaCG+BwhuBWPIy1aY5/gKVRNYGUdISAM2eHNpNxlLI0JYaA75Xh
Jn8sZArvM08nM/pLJdJvCo3sOvR8BsEX99O+tyd0Px58dMq9XsKd
=tCke
-----END PGP SIGNATURE-----
Merge tag 'v4.14-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Pull "Rockchip dts32 changes for 4.14" from Heiko Stübner:
Removal of the deprectated num-slots property from all Rockchip dw-mmc
nodes. The rv1108 gains support for sd-cards on the evaluation board and
the general nodes get a bit of cosmetic. On rk3288 the evb gains support
saradc and the adc-key connected to it while some more boards also get
their mali gpu enabled (fennec, evb, tinker).
The biggest set of changes can be found on the rk3228/rk3229 combo this
time. It gets core support for efuse, sdmmc, sdio, io-domans and spdif
as well as a separate rk3229.dtsi that will keep the slight differences
between the two brothers rk3228/rk3229. The evaluation board also gets
some attention and abled nodes (regulators, io-domains, emmc, tsadc keys)
But I think the most interesting change is the cpu enable-method for it.
Instead of using the older in-kernel method, we're now also moving to
handling this in firmware via the psci interface on 32bit Rockchip socs.
In a recently merged pull request [0] support for the rk3228/rk3229 was
added to OP-TEE including the psci support and it seems supporting other
32bit Rockchip socs that way is also planned for the future.
[0] https://github.com/OP-TEE/optee_os/pull/1666
* tag 'v4.14-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip: (23 commits)
ARM: dts: rockchip: fix property-ordering in rv1108 mmc nodes
ARM: dts: rockchip: enable sdmmc for rv1108 evb
ARM: dts: rockchip: add efuse device node for rk3228
ARM: dts: rockchip: add gpio power-key for rk3229-evb
ARM: dts: rockchip: enable tsadc for rk3229-evb
ARM: dts: rockchip: enable eMMC for rk3229-evb
ARM: dts: rockchip: enable io-domain for rk3229-evb
ARM: dts: rockchip: add cpu-supply property for cpu node of rk3229-evb
ARM: dts: rockchip: add regulator nodes for rk3229-evb
ARM: dts: rockchip: add sdmmc and sdio nodes for rk3228 SoC
ARM: dts: rockchip: fix compatible string for eMMC node of rk3228 SoC
ARM: dts: rockchip: add cpu enable method for rk3228 SoC
ARM: dts: rockchip: remove num-slots from all platforms
ARM: dts: rockchip: Add io-domain node for rk3228
ARM: dts: rockchip: add basic dtsi file for RK3229 SoC
ARM: dts: rockchip: enable adc key for rk3288-evb
ARM: dts: rockchip: enable saradc for rk3288-evb
ARM: dts: rockchip: enable ARM Mali GPU on rk3288-fennec
ARM: dts: rockchip: enable ARM Mali GPU on rk3288-evb
ARM: dts: rockchip: enable ARM Mali GPU on rk3288-tinker
...
Changes of note:
* Add pin controller support to the RZ/G1M (r8a7743) SoC and
RZ/A1 (r7s72100) SoCs now that the driver is available in v4.13-rc1.
* Add GPIO support to the RZ/G1M (r8a7743) SoC now that the driver
is availabe in v4.13-rc1.
* Enable MMCIF0 and Ethernet AVB support on the RZ/G1M (r8a7743) SoC and
the iWave-RZG1M-20M Qseven SOM. This depends on newly added pin
controller support noted above.
* Use R-Car Gen 2 fallback binding for vin nodes
This makes binding use consistent across R-Car Gen 2 SoCs.
It does not have any run-time effect
* Use SMP jump stub SRAM region from DT on R-Car Gen 2 SoCs
Geert Uytterhoeven says, "The R-Car Gen2 platform code for CPU core
bringup needs to copy a jump stub to on-SoC SRAM. Currently it uses a
hardcoded address pointing to ICRAM1."
* Add Inter Connect RAM to R-Car Gen 2 and RZ/G1 SoCs
Geert Uytterhoeven says, "R-Car Gen2 and RZ/G1 SoCs contain two or three
blocks of SRAM, which can be used for several purposes. One such purpose
is holding a jump stub for CPU core bringup."
* Use generic compatible string for I2C EEPROM for RZ/A1 (r7s72100) SoC
and koelsch board.
This is part of a tree-wide cleanup by Javier Martinez Canillas
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=jQvt
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt-for-v4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Pull "Renesas ARM Based SoC DT Updates for v4.14" from Simon Horman:
Changes of note:
* Add pin controller support to the RZ/G1M (r8a7743) SoC and
RZ/A1 (r7s72100) SoCs now that the driver is available in v4.13-rc1.
* Add GPIO support to the RZ/G1M (r8a7743) SoC now that the driver
is availabe in v4.13-rc1.
* Enable MMCIF0 and Ethernet AVB support on the RZ/G1M (r8a7743) SoC and
the iWave-RZG1M-20M Qseven SOM. This depends on newly added pin
controller support noted above.
* Use R-Car Gen 2 fallback binding for vin nodes
This makes binding use consistent across R-Car Gen 2 SoCs.
It does not have any run-time effect
* Use SMP jump stub SRAM region from DT on R-Car Gen 2 SoCs
Geert Uytterhoeven says, "The R-Car Gen2 platform code for CPU core
bringup needs to copy a jump stub to on-SoC SRAM. Currently it uses a
hardcoded address pointing to ICRAM1."
* Add Inter Connect RAM to R-Car Gen 2 and RZ/G1 SoCs
Geert Uytterhoeven says, "R-Car Gen2 and RZ/G1 SoCs contain two or three
blocks of SRAM, which can be used for several purposes. One such purpose
is holding a jump stub for CPU core bringup."
* Use generic compatible string for I2C EEPROM for RZ/A1 (r7s72100) SoC
and koelsch board.
This is part of a tree-wide cleanup by Javier Martinez Canillas
* tag 'renesas-dt-for-v4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (38 commits)
ARM: dts: iwg20m: Correct indentation of mmcif0 properties
ARM: dts: rskrza1: Add LED0 pin support
ARM: dts: rskrza1: Add SDHI1 pin group
ARM: dts: rskrza1: Add Ethernet pin group
ARM: dts: rskrza1: Add SCIF2 pin group
ARM: dts: genmai: Add ethernet pin group
ARM: dts: genmai: Add user led device nodes
ARM: dts: genmai: Add RIIC2 pin group
ARM: dts: genmai: Add SCIF2 pin group
ARM: dts: r7s72100: Add pin controller node
ARM: dts: iwg20m: Add MMCIF0 support
ARM: dts: r8a7794: Use R-Car Gen 2 fallback binding for vin nodes
ARM: dts: r8a7791: Use R-Car Gen 2 fallback binding for vin nodes
ARM: dts: r8a7790: Use R-Car Gen 2 fallback binding for vin nodes
ARM: dts: r8a7743: Add MMCIF0 support
ARM: dts: r8a7794: Reserve SRAM for the SMP jump stub
ARM: dts: r8a7793: Reserve SRAM for the SMP jump stub
ARM: dts: r8a7792: Reserve SRAM for the SMP jump stub
ARM: dts: r8a7791: Reserve SRAM for the SMP jump stub
ARM: dts: r8a7790: Reserve SRAM for the SMP jump stub
...
Highlights:
----------
-Add DMA support on STM32F746
-Add DMA support on STM32H743
-Add DAC support on STM32H743
-Add DAC support on STM32F429
-Add ADC support on STM32H743
-Enable ADC on stm32h743i-eval board
-Add CEC support on STM32F7xx MCUs
-Enable CEC on stm32f769-disco board
-Remove rdinit from stm32f4 boards
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=pZdf
-----END PGP SIGNATURE-----
Merge tag 'stm32-dt-for-v4.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into next/dt
Pull "STM32 DT updates for v4.14, round 1" from Alexandre Torgue:
Highlights:
----------
-Add DMA support on STM32F746
-Add DMA support on STM32H743
-Add DAC support on STM32H743
-Add DAC support on STM32F429
-Add ADC support on STM32H743
-Enable ADC on stm32h743i-eval board
-Add CEC support on STM32F7xx MCUs
-Enable CEC on stm32f769-disco board
-Remove rdinit from stm32f4 boards
* tag 'stm32-dt-for-v4.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32:
ARM: dts: stm32: Add DMA support for STM32H743 SoC
ARM: dts: stm32: Add DMA support for STM32F746 SoC
ARM: dts: stm32: enable ADC on stm32h743i-eval board
ARM: dts: stm32: add ADC support on stm32h743
ARM: dts: stm32: Add DAC support on stm32h743
ARM: dts: stm32: Add DAC support on stm32f429
ARM: dts: stm32: enable CEC for stm32f769 discovery
ARM: dts: stm32: add CEC for stm32f7 family
ARM: dts: stm32: reorder stm32h743 nodes
ARM: dts: stm32: Remove rdinit from bootargs on stm32f429-disco
ARM: dts: stm32: Remove rdinit from bootargs on stm32f429i-eval
ARM: dts: stm32: Remove rdinit from bootargs on stm32f469-disco
Remove deprecated and unneeded properties from Exynos boards.
-----BEGIN PGP SIGNATURE-----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=9f+j
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Pull "Samsung DTS ARM changes for v4.13" from Krzysztof Kozłowski:
Remove deprecated and unneeded properties from Exynos boards.
* tag 'samsung-dt-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Remove num-slots from exynos platforms
ARM: dts: exynos: Remove the OF graph from DSI node
Include dra72x-mmc-iodelay.dtsi which has pinmux and IODelay
configuration values for the various MMC modes for dra72 SoC
and use it in the pinctrl properties of MMC devicetree
nodes present in dra71-evm.dts.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Include dra72x-mmc-iodelay.dtsi which has pinmux and IODelay
configuration values for the various MMC modes for dra72 SoC
and use it in the pinctrl properties of MMC devicetree
nodes present in dra72-evm-revc.dts.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Include dra72x-mmc-iodelay.dtsi which has pinmux and IODelay
configuration values for the various MMC modes for dra72 SoC
and use it in the pinctrl properties of MMC devicetree
nodes present in dra72-evm.dts.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Include dra74x-mmc-iodelay.dtsi which has pinmux and IODelay
configuration values for the various MMC modes for dra74x SoC
and use it in the pinctrl properties of MMC devicetree
nodes present in am572x-idk.dts.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Include dra72x-mmc-iodelay.dtsi which has pinmux and IODelay
configuration values for the various MMC modes for dra72 SoC
and use it in the pinctrl properties of MMC devicetree
nodes present in am571x-idk.dts.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM572x IDK and AM571x IDK boards have equivalent
design of how SD card and eMMC are connected.
The two EVMs mainly differ in IOdelay configuration
needed (because of difference in SoC used).
Move the common properties to am57xx-idk-common.dtsi
file which is common for both EVMs.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Include dra74x-mmc-iodelay.dtsi which has pinmux and IODelay
configuration values for the various MMC modes for dra74 SoC
and use it in the pinctrl properties of MMC devicetree
nodes present in am57xx-beagle-x15/am57xx-beagle-x15-revb1.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Include dra74x-mmc-iodelay.dtsi which has pinmux and IODelay
configuration values for the various MMC modes for dra74 SoC
and use it in the pinctrl properties of MMC devicetree
nodes present in dra7-evm.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add pinmux configuration for MMC module including IODELAY
values suggested in the data manual for the various supported
modes.
IOdelay data for both silicon revision 1.1 and 2.0 is
added here.
The datamanual revisions used are:
* AM572x Silicon Revision 2.0: SPRS953B, Revised November 2016
* AM572x Silicon Revision 1.1: SPRS915R, Revised November 2016
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add pinmux configuration for MMC module including IODELAY
values suggested in the data manual for the various supported
modes.
IOdelay data for both silicon revision 1.0 and 2.0 is
added here.
The datamanual revisions used are:
* AM571x Silicon Revision 2.0: SPRS957D, Revised January 2017
* AM571x Silicon Revision 1.0: SPRS919M, Revised November 2017
* DRA71x : SPRS960B, Revised February 2017
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add NAND controller node to LD4, Pro4, sLD8, Pro5, and PXs2.
Set up pinctrl to enable 2 chip select lines except Pro4. The CS1
for Pro4 is multiplexed with other peripherals such as UART2, so
I did not enable it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
