Convert the PPv2 driver to implement phylink helpers, and use phylink in
DT mode. The other mode supported is ACPI, which will need further work
in order to be entirely compatible with phylink.
The MAC and GoP configuration functions were completely moved to fit
into the phylink helpers. When a PHY is always present between the MAC
and the physical port, phylink only is used, but when this is not the
case (the MAC directly is connected to the physical port) the link IRQ
is used to detect changes in the link state and call phylink_mac_change.
The ACPI mode do not uses phylink as of now, and the changes shouldn't
impact its use.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cosmetic patch to align the ethtool functions to ops definitions. This
patch does not change in any way the driver's behaviour.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of drivers have the following pattern:
if (np)
of_mdiobus_register()
else
mdiobus_register()
which the implementation of of_mdiobus_register() now takes care of.
Remove that pattern in drivers that strictly adhere to it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Reviewed-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell's PPv2.2 IP needs an additional clock named "MG Core clock".
This is required on Armada 7K and 8K.
This commit adds the required clock in mvpp2, making sure it's only
used on PPv2.2.
Fixes: c7e92def1e ("clk: mvebu: cp110: Fix clock tree representation")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When clk_prepare_enable fails for the axi_clk, the mg_clk isn't properly
cleaned up. Add another jump label to handle that case, and make sure we
jump to it in the later error cases.
Fixes: 4792ea04bc ("net: mvpp2: Fix clock resource by adding an optional bus clock")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PPv2 TX/RX descriptors uses 40bits DMA addresses, but 41 bits masks were
used (GENMASK_ULL(40, 0)).
This commit fixes that by using the correct mask.
Fixes: e7c5359f2e ("net: mvpp2: introduce PPv2.2 HW descriptors and adapt accessors")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell's PPv2 controller has a Packet Header parser, which uses a
fixed-size TCAM array of filter entries.
The mvpp2 driver reserves some ranges among the 256 TCAM entries to
perform MAC and VID filtering. The rest of the TCAM ids are freely usable
for other features, such as IPv4 proto matching.
This commit fixes the MVPP2_PE_LAST_FREE_TID define that sets the end of
the "free range", which included the MAC range. This could therefore allow
some other features to use entries dedicated to MAC filtering,
lowering the number of unicast/multicast addresses that could be allowed
before switching to promiscuous mode.
Fixes: 10fea26ce2 ("net: mvpp2: Add support for unicast filtering")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Boundary check in mvpp2_prs_init_from_hw must be done according to the
passed "tid" parameter, not the mvpp2_prs_entry index, which is not yet
initialized at the time of the check.
Fixes: 47e0e14eb1 ("net: mvpp2: Make mvpp2_prs_hw_read a parser entry init function")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current suspend/resume implementation reuses the mvneta_open() and
mvneta_close(), but it could be optimized to take only necessary
actions during suspend/resume.
One obvious problem of current implementation is: after hundreds of
system suspend/resume cycles, the resume of mvneta could fail due to
fragmented dma coherent memory. After this patch, the non-necessary
memory alloc/free is optimized out.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is to prepare the suspend/resume improvement in next patch. The
SW parts can be optimized out during resume.
As for rxq handling during suspend, we'd like to drop packets by
calling mvneta_rxq_drop_pkts() which is both SW and HW operation,
so we don't split rxq deinit.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sky2 ethernet stops working after system resume from suspend:
[ 582.852065] sky2 0000:04:00.0: Refused to change power state, currently in D3
The current 150ms delay is not enough, change it to 200ms can solve the
issue.
BugLink: https://bugs.launchpad.net/bugs/1758507
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor conflicts in drivers/net/ethernet/mellanox/mlx5/core/en_rep.c,
we had some overlapping changes:
1) In 'net' MLX5E_PARAMS_LOG_{SQ,RQ}_SIZE -->
MLX5E_REP_PARAMS_LOG_{SQ,RQ}_SIZE
2) In 'net-next' params->log_rq_size is renamed to be
params->log_rq_mtu_frames.
3) In 'net-next' params->hard_mtu is added.
Signed-off-by: David S. Miller <davem@davemloft.net>
In mvneta_port_up() we enable relevant RX and TX port queues by write
queues bit map to an appropriate register.
q_map must be ZERO in the beginning of this process.
Signed-off-by: Yelena Krivosheev <yelena@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The style of the rx/tx queue's *_coal member assignment is:
static void foo_coal_set(...)
{
set the coal in hw;
update queue's foo_coal member; [1]
}
In other place, we call foo_coal_set(pp, queue->foo_coal), so the above [1]
is duplicated and could be removed.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide a pointer to the SFP bus in struct net_device, so that the
ethtool module EEPROM methods can access the SFP directly, rather
than needing every user to provide a hook for it.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for having DSA transition entirely to PHYLINK, we need to pass a
PHY interface type to the mac_link_{up,down} callbacks because we may have to
make decisions on that (e.g: turn on/off RGMII interfaces etc.). We do not pass
an entire phylink_link_state because not all parameters (pause, duplex etc.) are
defined when the link is down, only link and interface are.
Update mvneta accordingly since it currently implements phylink_mac_ops.
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use relaxed I/O on the hot path. This achieves significant performance
improvements. On a 10G link, this makes a basic iperf TCP test go from
an average of 4.5 Gbits/sec to about 9.40 Gbits/sec.
Signed-off-by: Yan Markman <ymarkman@marvell.com>
[Maxime: Commit message, cosmetic changes]
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some helper functions that search for given entries in the TCAM filter
on PPv2 controller make use of dynamically alloced temporary variables,
allocated with GFP_KERNEL. These functions can be called in atomic
context, and dynamic alloc is not really needed in these cases anyways.
This commit gets rid of dynamic allocs and use stack allocation in the
following functions, and where they're used :
- mvpp2_prs_flow_find
- mvpp2_prs_vlan_find
- mvpp2_prs_double_vlan_find
- mvpp2_prs_mac_da_range_find
For all these functions, instead of returning an temporary object
representing the TCAM entry, we simply return the TCAM id that matches
the requested entry.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvpp2_prs_hw_read function uses the 'index' field of the struct
mvpp2_prs_entry to initialize the rest of the fields. This makes it
unclear from a caller's perspective, who needs to manipulate a struct
that is not entirely initialized.
This commit makes it an init function for prs_entry, by passing it the
index as a parameter. The function now zeroes the entry, and sets the
index field before doing all other init from HW.
The function is renamed 'mvpp2_prs_init_from_hw' to make that clear.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prefer the direct use of octal for permissions.
Done with checkpatch -f --types=SYMBOLIC_PERMS --fix-inplace
and some typing.
Miscellanea:
o Whitespace neatening around these conversions.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Array mvpp2_pools is being indexed by long_log_pool, however this
looks like a cut-n-paste bug and in fact should be short_log_pool.
Detected by CoverityScan, CID#1466113 ("Copy-paste error")
Fixes: 576193f2d5 ("net: mvpp2: jumbo frames support")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell PPv2 controller can be used to implement packet filtering based
on the destination MAC address. This is already used to implement
multicast filtering. This patch adds support for Unicast filtering.
Filtering is based on so-called "TCAM entries" to implement filtering.
Due to their limited number and the fact that these are also used for
other purposes, we reserve 80 entries for both unicast and multicast
filters. On top of the broadcast address, and each interface's own MAC
address, we reserve 25 entries per port, 4 for unicast filters, 21 for
multicast.
Whenever unicast or multicast range for one port is full, the filtering
is disabled and port goes into promiscuous mode for the given type of
addresses.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvpp2_prs_mac_da_accept function takes into parameter both the
struct representing the controller and the port id. This is meaningful
when we want to create TCAM entries for non-initialized ports, but in
this case we expect the port to be initialized before starting adding or
removing MAC addresses to the per-port filter.
This commit changes the function so that it takes struct mvpp2_port as
a parameter instead.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: effbf5f58d ("net: mvpp2: update the BM buffer free/destroy logic")
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the support for jumbo frames in the Marvell PPv2 driver.
A third buffer pool is added with 10KB buffers, which is used if the MTU
is higher than 1518B for packets larger than 1518B. Please note only the
port 0 supports hardware checksum offload due to the Tx FIFO size
limitation.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
[Antoine: cosmetic cleanup, commit message]
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the NETIF_F_IPV6_CSUM to the driver's features to enable
UDP/TCP checksum over IPv6. No extra configuration of the engine is
needed on top of the IPv4 counterpart, which already is in the features
list (NETIF_F_IP_CSUM).
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch sets the Tx FIFO data size on port 0 to 10kB. This prepares
the PPv2 driver for the Jumbo frame support addition as the hardware
will need big enough Tx FIFO buffers when dealing with frames going
through an interface with an MTU of 9000.
Signed-off-by: Yan Markman <ymarkman@marvell.com>
[Antoine: commit message, small reworks.]
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The buffer free routine is updated to release only given a number of
buffers, and the destroy routine now checks the actual number of buffers
in the (BPPI and BPPE) HW counters before draining the pools. This
change helps getting jumbo frames support.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
[Antoine: cosmetic cleanup, commit message]
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch configures the buffer manager long pool for all ports part of
the same CP. Long pool separation between ports is redundant since there
are no performance improvement when different pools are used.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
[Antoine: cosmetic cleanup, commit message]
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell PPv2 controller allows for generic packet filtering. This commit
adds entries to implement VLAN filtering. The approach taken is :
- Filter entries that would match on the presence of the VLAN tag
(existing VLAN detection, DSA / EDSA detection) will set the next
lookup ID to be for the VID.
- For each VLAN existing on a given port, we add an entry that matches
this specific VID. If the incoming packet matches the VID entry, it is
set for the next lookup in the chain (LU_L2).
- A Guard entry is added for each port, that will match if the incoming
packet didn't match any of the above VID entries. This entry tags the
packet to be dropped.
Due to this design, and the fact that the total 256 filter entries are
also used for other purposes, we have a limit of 10 VLANs per port. To
accommodate the case where we would need more VLANS on one port, this
patch implements the ndo_set_features to allow for disabling of VLAN
filtering using ethtool.
The default config has VLAN filtering disabled.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 doesn't work on the MacchiatoBIN board. It is caused by broken
multicast address filter in the mvpp2 driver.
The driver loads doesn't load any multicast entries if "allmulti" is not
set. This condition should be reversed.
The condition !netdev_mc_empty(dev) is useless (because
netdev_for_each_mc_addr is nop if the list is empty).
This patch also fixes a possible overflow of the multicast list - if
mvpp2_prs_mac_da_accept fails, we set the allmulti flag and retry.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
This implements ndo_poll_controller callback which is necessary to
enable netconsole.
Signed-off-by: Alexander Monakov <amonakov@ispras.ru>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces an alternative way of obtaining resources - via
ACPI tables provided by firmware. Enabling coexistence with the DT
support, in addition to the OF_*->device_*/fwnode_* API replacement,
required following steps to be taken:
* Add mvpp2_acpi_match table
* Omit clock configuration and obtain tclk from the property - in ACPI
world, the firmware is responsible for clock maintenance.
* Disable comphy and syscon handling as they are not available for ACPI.
* Modify way of obtaining interrupts - use newly introduced
fwnode_irq_get() routine
* Until proper MDIO bus and PHY handling with ACPI is established in the
kernel, use only link interrupts feature in the driver. For the RGMII
port it results in depending on GMAC settings done during firmware
stage.
* When booting with ACPI MVPP2_QDIST_MULTI_MODE is picked by
default, as there is no need to keep any kind of the backward
compatibility.
Moreover, a memory region used by mvmdio driver is usually placed in
the middle of the address space of the PP2 network controller.
The MDIO base address is obtained without requesting memory region
(by devm_ioremap() call) in mvmdio.c, later overlapping resources are
requested by the network driver, which is responsible for avoiding
a concurrent access.
In case the MDIO memory region is declared in the ACPI, it can
already appear as 'in-use' in the OS. Because it is overlapped by second
region of the network controller, make sure it is released, before
requesting it again. The care is taken by mvpp2 driver to avoid
concurrent access to this memory region.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
OF functions can be used only for the driver using DT.
As a preparation for introducing ACPI support in mvpp2
driver, use struct fwnode_handle in order to obtain
properties from the hardware description.
This patch replaces of_* function with device_*/fwnode_*
where possible in the mvpp2.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'port_count' field of the mvpp2 structure holds an overall amount
of available ports, based on DT nodes status. In order to be prepared
to support other HW description, obtain the value by incrementing it
upon each successful port initialization. This allowed for simplifying
port indexing in the controller's private array, whose size is now not
dynamically allocated, but fixed to MVPP2_MAX_PORTS.
This patch simplifies creating and filling list of enabled ports and
is a part of the preparation for adding ACPI support in the mvpp2 driver.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for reading the SFF module's EEPROM via the ethtool API.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PSC sync change interrupt can fire multiple times while the link is
down, which is caused by noise on the serdes lines. As this isn't
information we make use of, it's pointless having the interrupt enabled.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the port configuration and release of reset to mvneta_mac_config()
along side the rest of the port mode configuration.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert mvneta to use phylink, which models the MAC to PHY link in
a generic, reusable form.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- remove unused sync status
Signed-off-by: David S. Miller <davem@davemloft.net>
Prepare to convert mvneta to phylink by splitting the adjust_link
function into its consituent parts.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netdev core always ensures that the rtnl lock is held while calling
the ndo_open() and ndo_stop() methods. However, the suspend/resume paths
do not hold the rtnl lock. phylink will expect the rtnl lock to be held
when the MAC driver calls it, so we end up with kernel warnings. Take
the lock to ensure that these functions are called in a consistent
manner.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
sky2_vpd_wait is not called in an interrupt handler nor holding a spinlock.
The function mdelay in it can be replaced with msleep, to reduce busy wait.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lots of overlapping changes. Also on the net-next side
the XDP state management is handled more in the generic
layers so undo the 'net' nfp fix which isn't applicable
in net-next.
Include a necessary change by Jakub Kicinski, with log message:
====================
cls_bpf no longer takes care of offload tracking. Make sure
netdevsim performs necessary checks. This fixes a warning
caused by TC trying to remove a filter it has not added.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There are few reasons in mvneta_rx_swbm() function when received packet
is dropped. mvneta_rx_error() should be called only if error bit [16]
is set in rx descriptor.
[gregory.clement@free-electrons.com: add fixes tag]
Cc: stable@vger.kernel.org
Fixes: dc35a10f68 ("net: mvneta: bm: add support for hardware buffer management")
Signed-off-by: Yelena Krivosheev <yelena@marvell.com>
Tested-by: Dmitri Epshtein <dima@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding the RX queue association with each CPU, a typo was made in
the mvneta_cleanup_rxqs() function. This patch fixes it.
[gregory.clement@free-electrons.com: add commit log and fixes tag]
Cc: stable@vger.kernel.org
Fixes: 2dcf75e279 ("net: mvneta: Associate RX queues with each CPU")
Signed-off-by: Yelena Krivosheev <yelena@marvell.com>
Tested-by: Dmitri Epshtein <dima@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When port connect to PHY in polling mode (with poll interval 1 sec),
port and phy link status must be synchronize in order don't loss link
change event.
[gregory.clement@free-electrons.com: add fixes tag]
Cc: <stable@vger.kernel.org>
Fixes: c5aff18204 ("net: mvneta: driver for Marvell Armada 370/XP network unit")
Signed-off-by: Yelena Krivosheev <yelena@marvell.com>
Tested-by: Dmitri Epshtein <dima@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Three sets of overlapping changes, two in the packet scheduler
and one in the meson-gxl PHY driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
The code to handle multi-port SKGE boards was freeing IRQ
twice. The first one was under lock and might sleep.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adjust the coalescing parameters to the vendor
recommendations for the PPv2 network controller.
Suggested-by: Yan Markman <ymarkman@marvell.com>
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the tx-usec value to the informations reported to
ethtool by the get_coalesce function.
Suggested-by: Yan Markman <ymarkman@marvell.com>
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cosmetic patch aligning values in the ethtool get_coalesce function.
This patch do not modify in anyway the driver's behaviour.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Rx/Tx ring sizes can be adjusted thanks to ethtool given specific
network needs. This commit splits the default ring size from its max
value to allow ethtool to vary the parameters in both ways.
Signed-off-by: Yan Markman <ymarkman@marvell.com>
[Antoine: commit message]
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a check to only free the TSO header buffer when its
allocation previously succeeded.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The macro used to access or set an RSS table entry was using an offset
of 8, while it should use an offset of 0. This lead to wrongly configure
the RSS table, not accessing the right entries.
Fixes: 1d7d15d79f ("net: mvpp2: initialize the RSS tables")
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
add appropriate calls to clk_disable_unprepare() by jumping to out_mdio
in case orion_mdio_probe() returns -EPROBE_DEFER.
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: 3d604da1e9 ("net: mvmdio: get and enable optional clock")
Signed-off-by: Tobias Jordan <Tobias.Jordan@elektrobit.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reserved and unused fields in the Tx descriptors should be 0. The PPv2
driver doesn't clear them at run-time (for performance reasons) but
these descriptors aren't zeroed when allocated, which can lead to
unpredictable behaviors. This patch fixes this by using
dma_zalloc_coherent instead of dma_alloc_coherent.
Fixes: 3f518509de ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: Yan Markman <ymarkman@marvell.com>
[Antoine: commit message]
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) The forcedeth conversion from pci_*() DMA interfaces to dma_*() ones
missed one spot. From Zhu Yanjun.
2) Missing CRYPTO_SHA256 Kconfig dep in cfg80211, from Johannes Berg.
3) Fix checksum offloading in thunderx driver, from Sunil Goutham.
4) Add SPDX to vm_sockets_diag.h, from Stephen Hemminger.
5) Fix use after free of packet headers in TIPC, from Jon Maloy.
6) "sizeof(ptr)" vs "sizeof(*ptr)" bug in i40e, from Gustavo A R Silva.
7) Tunneling fixes in mlxsw driver, from Petr Machata.
8) Fix crash in fanout_demux_rollover() of AF_PACKET, from Mike
Maloney.
9) Fix race in AF_PACKET bind() vs. NETDEV_UP notifier, from Eric
Dumazet.
10) Fix regression in sch_sfq.c due to one of the timer_setup()
conversions. From Paolo Abeni.
11) SCTP does list_for_each_entry() using wrong struct member, fix from
Xin Long.
12) Don't use big endian netlink attribute read for
IFLA_BOND_AD_ACTOR_SYSTEM, it is in cpu endianness. Also from Xin
Long.
13) Fix mis-initialization of q->link.clock in CBQ scheduler, preventing
adding filters there. From Jiri Pirko.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (67 commits)
ethernet: dwmac-stm32: Fix copyright
net: via: via-rhine: use %p to format void * address instead of %x
net: ethernet: xilinx: Mark XILINX_LL_TEMAC broken on 64-bit
myri10ge: Update MAINTAINERS
net: sched: cbq: create block for q->link.block
atm: suni: remove extraneous space to fix indentation
atm: lanai: use %p to format kernel addresses instead of %x
VSOCK: Don't set sk_state to TCP_CLOSE before testing it
atm: fore200e: use %pK to format kernel addresses instead of %x
ambassador: fix incorrect indentation of assignment statement
vxlan: use __be32 type for the param vni in __vxlan_fdb_delete
bonding: use nla_get_u64 to extract the value for IFLA_BOND_AD_ACTOR_SYSTEM
sctp: use right member as the param of list_for_each_entry
sch_sfq: fix null pointer dereference at timer expiration
cls_bpf: don't decrement net's refcount when offload fails
net/packet: fix a race in packet_bind() and packet_notifier()
packet: fix crash in fanout_demux_rollover()
sctp: remove extern from stream sched
sctp: force the params with right types for sctp csum apis
sctp: force SCTP_ERROR_INV_STRM with __u32 when calling sctp_chunk_fail
...
This patch fixes the Tx ring size checks when using ethtool, by adding
an extra check in the PPv2 check_ringparam_valid helper. The Tx ring
size cannot be set to a value smaller than the minimum number of
descriptors needed for TSO.
Fixes: 1d17db08c0 ("net: mvpp2: limit TSO segments and use stop/wake thresholds")
Suggested-by: Yan Markman <ymarkman@marvell.com>
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Short fragmented packets may never be sent by the hardware when padding
is disabled. This patch stop modifying the GMAC padding bits, to leave
them to their reset value (disabled).
Fixes: 3919357fb0 ("net: mvpp2: initialize the GMAC when using a port")
Signed-off-by: Yan Markman <ymarkman@marvell.com>
[Antoine: commit message]
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patches fixes the probe error path by cleaning up probed ports, to
avoid leaving registered net devices when the driver failed to probe.
Fixes: 3f518509de ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an allocation in the txq_init path fails, the allocated buffers
end-up being freed twice: in the txq_init error path, and in txq_deinit.
This lead to issues as txq_deinit would work on already freed memory
regions:
kernel BUG at mm/slub.c:3915!
Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
This patch fixes this by removing the txq_init own error path, as the
txq_deinit function is always called on errors. This was introduced by
TSO as way more buffers are allocated.
Fixes: 186cd4d4e4 ("net: mvpp2: software tso support")
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvneta controller provides a 8-bit register to update the pending
Tx descriptor counter. Then, a maximum of 255 Tx descriptors can be
added at once. In the current code the mvneta_txq_pend_desc_add function
assumes the caller takes care of this limit. But it is not the case. In
some situations (xmit_more flag), more than 255 descriptors are added.
When this happens, the Tx descriptor counter register is updated with a
wrong value, which breaks the whole Tx queue management.
This patch fixes the issue by allowing the mvneta_txq_pend_desc_add
function to process more than 255 Tx descriptors.
Fixes: 2a90f7e1d5 ("net: mvneta: add xmit_more support")
Cc: stable@vger.kernel.org # 4.11+
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
GOP statistics from all ports of one instance of the driver are gathered
with one work recalled in loop in a workqueue. The loop is started when
a port is up, and stopped when a port is down. This last condition is
obviously wrong.
Fix this by having a work per port. This way, starting and stoping it
when the port is up or down will be fine, while minimizing unnecessary
CPU usage.
Fixes: 118d6298f6 ("net: mvpp2: add ethtool GOP statistics")
Reported-by: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simple cases of overlapping changes in the packet scheduler.
Must easier to resolve this time.
Which probably means that I screwed it up somehow.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ethtool statistics support by reading the GOP statistics from the
hardware counters. Also implement a workqueue to gather the statistics
every second or some 32-bit counters could overflow.
Suggested-by: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvpp2 driver can't cope at all with the TX affinities being
changed from userspace, and spit an endless stream of
[ 91.779920] mvpp2 f4000000.ethernet eth2: wrong cpu on the end of Tx processing
[ 91.779930] mvpp2 f4000000.ethernet eth2: wrong cpu on the end of Tx processing
[ 91.780402] mvpp2 f4000000.ethernet eth2: wrong cpu on the end of Tx processing
[ 91.780406] mvpp2 f4000000.ethernet eth2: wrong cpu on the end of Tx processing
[ 91.780415] mvpp2 f4000000.ethernet eth2: wrong cpu on the end of Tx processing
[ 91.780418] mvpp2 f4000000.ethernet eth2: wrong cpu on the end of Tx processing
rendering the box completely useless (I've measured around 600k
interrupts/s on a 8040 box) once irqbalance kicks in and start
doing its job.
Obviously, the driver was never designed with this in mind. So let's
work around the problem by preventing userspace from interacting
with these interrupts altogether.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Files removed in 'net-next' had their license header updated
in 'net'. We take the remove from 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWfswbQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykvEwCfXU1MuYFQGgMdDmAZXEc+xFXZvqgAoKEcHDNA
6dVh26uchcEQLN/XqUDt
=x306
-----END PGP SIGNATURE-----
Merge tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull initial SPDX identifiers from Greg KH:
"License cleanup: add SPDX license identifiers to some files
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the
'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally
binding shorthand, which can be used instead of the full boiler plate
text.
This patch is based on work done by Thomas Gleixner and Kate Stewart
and Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset
of the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to
license had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied
to a file was done in a spreadsheet of side by side results from of
the output of two independent scanners (ScanCode & Windriver)
producing SPDX tag:value files created by Philippe Ombredanne.
Philippe prepared the base worksheet, and did an initial spot review
of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537
files assessed. Kate Stewart did a file by file comparison of the
scanner results in the spreadsheet to determine which SPDX license
identifier(s) to be applied to the file. She confirmed any
determination that was not immediately clear with lawyers working with
the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained
>5 lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that
was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that
became the concluded license(s).
- when there was disagreement between the two scanners (one detected
a license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply
(and which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases,
confirmation by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.
The Windriver scanner is based on an older version of FOSSology in
part, so they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot
checks in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect
the correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial
patch version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch
license was not GPL-2.0 WITH Linux-syscall-note to ensure that the
applied SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
License cleanup: add SPDX license identifier to uapi header files with a license
License cleanup: add SPDX license identifier to uapi header files with no license
License cleanup: add SPDX GPL-2.0 license identifier to files with no license
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Two functions were always used to set the DMA addresses in Tx
descriptors, because this address is split into a base+offset in the
descriptors. A mask was used to come up with the base and offset
addresses and two functions were called, mvpp2_txdesc_dma_addr_set() and
mvpp2_txdesc_offset_set().
This patch moves the base+offset calculation logic to
mvpp2_txdesc_dma_addr_set(), and removes mvpp2_txdesc_offset_set() to
simplify things.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cosmetic patch using the MVPP2_AGGR_TXQ_SIZE everywhere instead of the
size field of aggr_txq, as the size never change and is always equal to
the MVPP2_AGGR_TXQ_SIZE define.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Too many TSO descriptors can be required for the default queue size,
when using small MSS values for example. Prevent this by adding a
maximum number of allowed TSO segments (300). In addition set a stop and
a wake thresholds to stop the queue when there's no room for a 1 "worst
case scenario skb". Wake up the queue when the number of descriptors is
low enough.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch initialize the RSS tables to evenly (depending on the packets
RSS hashes) distribute the packets across port Rx queues. This helps to
handle packets on different CPUs to improve performances, as more queues
will be used in parallel.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far only the Rx FIFO size was initialized. For PPv2.2 the Tx FIFO
size can be set as well. This patch initializes the Tx FIFO size for
PPv2.2 controllers to 3K.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Rx FIFO size was set to the same value for all ports. This patch
sets it depending on the maximum speed a given port can handle. This is
only working for PPv2.2.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several conflicts here.
NFP driver bug fix adding nfp_netdev_is_nfp_repr() check to
nfp_fl_output() needed some adjustments because the code block is in
an else block now.
Parallel additions to net/pkt_cls.h and net/sch_generic.h
A bug fix in __tcp_retransmit_skb() conflicted with some of
the rbtree changes in net-next.
The tc action RCU callback fixes in 'net' had some overlap with some
of the recent tcf_block reworking.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces GFP_KERNEL by GFP_ATOMIC to avoid sleeping in the
ndo_set_rx_mode() call which is called with BH disabled.
Fixes: 3f518509de ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When calling mvpp2_prs_mac_multi_set() from mvpp2_prs_mac_init(), two
parameters (the port index and the table index) are inverted. Fixes
this.
Fixes: 3f518509de ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a typo in the mvpp2_prs_tcam_data_cmp() function, as
the shift value is inverted with the data.
Fixes: 3f518509de ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When Tx IRQs are used, txq_bufs_free() can be called from both the Tx
path and from NAPI poll(). This led to CPU stalls as if these two tasks
(Tx and Poll) are scheduled on two CPUs at the same time, DMA unmapping
operations are done on the same txq buffers.
This patch adds a check not to call txq_done() from the Tx path if Tx
interrupts are used as it does not make sense to do so.
Fixes: edc660fa09 ("net: mvpp2: replace TX coalescing interrupts with hrtimer")
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TSO header buffers are coming from a per cpu pool and should not
be unmapped as they are reused. The PPv2 driver was unmapping all
descriptors buffers unconditionally. This patch fixes this by checking
the buffers dma addresses before unmapping them, and by not unmapping
those who are located in the TSO header pool.
Fixes: 186cd4d4e4 ("net: mvpp2: software tso support")
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TSO headers are managed with txq index and therefore should be aligned
with the txq size, not with the aggregated txq size.
Fixes: 186cd4d4e4 ("net: mvpp2: software tso support")
Reported-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Yan Markman <ymarkman@marvell.com>
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On Armada 7K/8K we need to explicitly enable the bus clock. The bus clock
is optional because not all the SoCs need them but at least for Armada
7K/8K it is actually mandatory.
The binding documentation is updating accordingly.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch stops the internal MAC Tx clock from being enabled as the
internal clock isn't used. The definition used for the bit controlling
this behaviour is renamed as well as it was wrongly named (bit 4 of
GMAC_CTRL_2_REG).
Fixes: 3919357fb0 ("net: mvpp2: initialize the GMAC when using a port")
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private port_list array has a list of pointers to mvpp2_port
instances. This list is allocated given the number of ports enabled in
the device tree, but the pointers are set using the port-id property. If
on a single port is enabled, the port_list array will be of size 1, but
when registering the port, if its id is not 0 the driver will crash.
Other crashes were encountered in various situations.
This fixes the issue by using an index not equal to the value of the
port-id property.
Fixes: 3f518509de ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Yan Markman <ymarkman@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Parsing fragmentation detection failed due to wrong configured
parser TCAM entry's. Some traffic was marked as fragmented in RX
descriptor, even it wasn't IP fragmented. The hardware also failed to
calculate checksums which lead to use software checksum and caused
performance degradation.
Fixes: 3f518509de ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove a goto in the PPv2 tx function which jumps to the next line
anyway. This is a cosmetic commit.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
... and __initconst if applicable.
Based on similar work for an older kernel in the Grsecurity patch.
[JD: fix toshiba-wmi build]
[JD: add htcpen]
[JD: move __initconst where checkscript wants it]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
When using a mac address described in the device tree, a check is made
to see if it is valid. When it's not, no fallback is defined. This
patches tries to get the mac address from h/w (or use a random one if
the h/w one isn't valid) when the dt mac address isn't valid.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MAC retrieval logic is using a variable to store an h/w stored mac
address and checks this mac against invalid ones before using it. But
the mac address is only read from h/w when using PPv2.1. So when using
PPv2.2 it defaults to its init state.
This patches fixes the logic to only check if the h/w mac is valid when
actually retrieving a mac from h/w.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MAC retrieval has a quite complicated logic (which is broken). Moves
it to its own function to prepare for patches fixing its logic, so that
reviews are easier.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvneta driver and hardware supports IPv6 offload, however it
isn't enabled. Set the NETIF_F_IPV6_CSUM feature to inform the
network layer that this driver can offload IPV6 TCP and UDP
checksums. This change has been tested on an Armada 370 and the
feature support confirmed with several device datasheets
including the Armada XP and Armada 3700.
Signed-off-by: Andrew Pilloud <andrewpilloud@igneoussystems.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the GoP link interrupt support for when a port isn't
connected to a PHY. Because of this the phylib callback is never called
and the link status management isn't done. This patch use the GoP link
interrupt in such cases to still have a minimal link management. Without
this patch ports not connected to a PHY cannot work.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is not necessarily a PHY between the GoP and the physical port.
However, the driver currently makes the "phy" property mandatory,
contrary to what is stated in the device tree bindings. This patch makes
the PHY optional, and aligns the PPv2 driver on its device tree
documentation. However if a PHY is provided, the GoP link interrupt
won't be used.
With this patch switches directly connected to the serdes lanes and SFP
ports on the Armada 8040-db and Armada 7040-db can be used if the link
interrupt is described in the device tree.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert all RGMII checks to use the phy_interface_mode_is_rgmii()
helper. This is a cosmetic patch.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds logic to reconfigure the comphy/GoP/MAC when the link
state is updated at runtime. This is very useful on boards where many
link speed are supported: depending on what is negotiated the PPv2
driver will automatically reconfigures the link between the PHY and the
MAC.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using the XLG MAC, it does not make sense to force the GMAC autoneg
parameters. This patch adds checks to only set the GMAC autoneg
parameters when needed (i.e. when not using the XLG MAC).
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the link status changes, the phylib calls the link_event function
in the mvpp2 driver. Before this patch only the egress/ingress transmit
was enabled/disabled. This patch adds more functionality to the link
status management code by enabling/disabling the port per-cpu
interrupts, and the port itself. The queues are now stopped as well, and
the netif carrier helpers are called.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The link_event function is somewhat complicated. This cosmetic patch
simplifies it.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some platforms, the comphy is between the MAC GoP and the PHYs. The
mvpp2 driver currently relies on the firmware/bootloader to configure
the comphy. As a comphy driver was added to the generic PHY framework,
this patch uses it in the mvpp2 driver to configure the comphy at boot
time to avoid relying on the bootloader.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mac address is only retrieved from h/w when using PPv2.1. Otherwise
the variable holding it is still checked and used if it contains a valid
value. As the variable isn't initialized to an invalid mac address
value, we end up with random mac addresses which can be the same for all
the ports handled by this PPv2 driver.
Fixes this by initializing the h/w mac address variable to {0}, which is
an invalid mac address value. This way the random assignation fallback
is called and all ports end up with their own addresses.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Fixes: 2697582144 ("net: mvpp2: handle misc PPv2.1/PPv2.2 differences")
Signed-off-by: David S. Miller <davem@davemloft.net>
The MVPP22_XLG_CTRL1_FRAMESIZELIMIT define is used as an offset, but is
defined as BIT(0). Updated its name to contains "OFFS" as in offset and
fix its value using the offset value, 0.
Reported-by: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Fixes: 76eb1b1de5 ("net: mvpp2: set maximum packet size for 10G ports")
Signed-off-by: David S. Miller <davem@davemloft.net>
txq_reclaim() does the normal transmit queue reclamation and
rxq_deinit() does the RX ring cleanup, none of these are packet drops,
so use dev_consume_skb() for both locations.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch uses the tso API to implement the tso functionality in Marvell
PPv2 driver.
Using iperf and 10G ports, using TSO shows a significant performance
improvement by a factor 2 to reach around 9.5Gbps in TX; as well as a
significant CPU usage drop (from 25% to 15%).
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The txq size is defined by MVPP2_AGGR_TXQ_SIZE, which is sometime not
used directly but through variables. As it is a fixed value use the
define everywhere in the driver.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TSO header size was defined in many drivers. Factorize the code and
define its size in net/tso.h.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds GoP (group of ports) initialization functions. The mvpp2
driver was relying on the firmware/bootloader initialization; this patch
moves this setup to the mvpp2 driver.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set maximum packet size for XLG 10G ports. Missing maximum packet size
for XLG configuration will cause kernel panic if oversized packet is
received by port.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds a routine to initialize the XLG MAC at the port level when
using a port and the XAUI/10GKR interface mode. This wasn't done until
this commit, and the mvpp2 driver was relying on the bootloader/firmware
initialization. This doesn't mean everything is configured in the mvpp2
driver now, but it helps reducing the gap.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds a routine to initialize the GMAC at the port level when using
a port. This wasn't done until this commit, and the mvpp2 driver was
relying on the bootloader/firmware initialization. This doesn't mean
everything is configured in the mvpp2 driver now, but it helps reducing
the gap.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This moves the mii configuration in the ndo_open path, to allow handling
different mii configurations later and to switch between these
configurations at runtime.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The macro defining the bit to toggle to bypass or not the
synchronization module is wrongly named. Writing 1 will disable bypass.
This patch s/MVPP22_CTRL4_SYNC_BYPASS/MVPP22_CTRL4_SYNC_BYPASS_DIS/.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cosmetic patch to use the same formatting rules on all register
definitions.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit adds the support for two related features:
- Support for TX interrupts, with one interrupt for each CPU
- Support for different RX queue distribution modes
MVPP2_QDIST_SINGLE_MODE where a single interrupt, shared by all
CPUs, receives the RX events, and MVPP2_QDIST_MULTI_MODE, where the
per-CPU interrupts used for TX events are also used for RX events.
Since additional interrupts are needed, an update to the Device Tree
binding is needed. However, backward compatibility is preserved with
the old Device Tree binding, by gracefully degrading to the original
behavior, with only one RX interrupt, and TX completion being handled
by an hrtimer.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to the introduction of TX interrupts and improved RX
queue distribution, this commit introduces the concept of "queue
vector". A queue vector represents a number of RX and/or TX queues,
and an associated NAPI instance and interrupt.
This commit currently only creates a single queue_vector, so there are
no changes in behavior, but it paves the way for additional
queue_vector in the next commits.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PPv2.2 IP has a concept of "software thread", with all registers
of the PPv2.2 mapped 8 times, for concurrent accesses by 8 "software
threads". In addition, interrupts on RX queues are associated to such
"software thread".
For most cases, we map a "software thread" to the more conventional
concept of CPU, but we will soon have one exception: we will have a
model where we have one TX interrupt per CPU (each using one software
thread), and all RX events mapped to another software thread
(associated to another interrupt).
In preparation for this change, it makes sense to change the naming
from MVPP2_MAX_CPUS to MVPP2_MAX_THREADS, and plan for 8 software
threads instead of 4 currently.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the global variables rxq_number and txq_number hold the
number of per-port TXQs and RXQs. Until now, such numbers were
constant regardless of the driver configuration. As we are going to
introduce different modes for TX and RX queues, these numbers will
depend on the configuration (PPv2.1 vs. PPv2.2, exact queue
distribution logic).
Therefore, as a preparation, we move the number of RXQs and TXQs in
the 'struct mvpp2_port' structure, next to the RXQs and TXQs
descriptor arrays.
For now, they remain initialized to the same default values as
rxq_number/txq_number used to be initialized, but this will change in
future commits.
The only non-mechanical change in this patch is that the check to
verify hardware constraints on the number of RXQs and TXQs is moved
from mvpp2_probe() to mvpp2_port_probe(), since it's now in
mvpp2_port_probe() that we initialize the per-port count of RXQ and
TXQ.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RX queue group allocation is anyway re-done later in
mvpp2_port_init(), so resetting it in mvpp2_init() is not very useful,
and will be annoying as we are going to rework the RX queue group
allocation logic.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MVPP21_ISR_RXQ_GROUP_REG register is not indexed by rxq, but by
port, so we fix the parameter name accordingly. There are no
functional changes.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_irq_to_resource() has recently been fixed to return negative error #'s
along with 0 in case of failure, however the Marvell MV643xx Ethernet
driver still only regards 0 as invalid IRQ -- fix it up.
Fixes: 7a4228bbff ("of: irq: use of_irq_get() in of_irq_to_resource()")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When all a function does is calling another function with the exact same
arguments, in the exact same order, you know it's time to remove said
function. Which is exactly what this commit does.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function is not used in the driver, remove it.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A previous commit modified a number of smp_processor_id() used in
migration-enabled contexts into get_cpu/put_cpu sections. However, a few
smp_processor_id() calls remain in the driver, and this commit adds
comments explaining why they can be kept.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cosmetic patch simplifying the smi read and write error paths. It also
align their error paths with the ones of the xsmi functions.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the xmdio xsmi interface support in the mvmdio driver.
This interface is used in Ethernet controllers on Marvell 370, 7k and 8k
(as of now). The xsmi interface supported by this driver complies with
the IEEE 802.3 clause 45. The xSMI interface is used by 10GbE devices.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a check for the read and write smi operations, to ensure the
MII_ADDR_C45 bit isn't set. This will be needed as soon as the xSMI
support is added to the mvmdio driver.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Put the two poll intervals (min and max) in the driver's ops
structure. This is needed to add the xmdio support later.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce an ops structure to add an indirection on the is_done
function, as this is needed to add the xMDIO support later.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MDIO layer already provides per-bus locking, so there's no need for
MDIO bus drivers to do their own internal locking. Remove this.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cosmetic patch to use the GENMASK helper for masks.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cosmetic patch replacing spaces by tabs for defined values.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cosmetic fix reordering headers alphabetically.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A common pattern with skb_put() is to just want to memcpy()
some data into the new space, introduce skb_put_data() for
this.
An spatch similar to the one for skb_put_zero() converts many
of the places using it:
@@
identifier p, p2;
expression len, skb, data;
type t, t2;
@@
(
-p = skb_put(skb, len);
+p = skb_put_data(skb, data, len);
|
-p = (t)skb_put(skb, len);
+p = skb_put_data(skb, data, len);
)
(
p2 = (t2)p;
-memcpy(p2, data, len);
|
-memcpy(p, data, len);
)
@@
type t, t2;
identifier p, p2;
expression skb, data;
@@
t *p;
...
(
-p = skb_put(skb, sizeof(t));
+p = skb_put_data(skb, data, sizeof(t));
|
-p = (t *)skb_put(skb, sizeof(t));
+p = skb_put_data(skb, data, sizeof(t));
)
(
p2 = (t2)p;
-memcpy(p2, data, sizeof(*p));
|
-memcpy(p, data, sizeof(*p));
)
@@
expression skb, len, data;
@@
-memcpy(skb_put(skb, len), data, len);
+skb_put_data(skb, data, len);
(again, manually post-processed to retain some comments)
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make return value void since function never return meaningfull value
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On GOP port 0 two MAC modes are available: GMAC and XLG. The XLG MAC is
used for 10G connectivity. This patch adds a basic 10G support by
allowing to use the XLG MAC on port 0 and by reworking the
port_enable/disable functions so that the XLG MAC is configured when
using 10G.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
smp_processor_id() should not be used in migration-enabled contexts. We
originally thought it was OK in the specific situation of this driver,
but it was wrong, and calling smp_processor_id() in a migration-enabled
context prints a big fat warning when CONFIG_DEBUG_PREEMPT=y.
Therefore, this commit replaces the smp_processor_id() in
migration-enabled contexts by the appropriate get_cpu/put_cpu sections.
Reported-by: Marc Zyngier <marc.zyngier@arm.com>
Fixes: a786841df7 ("net: mvpp2: handle register mapping and access for PPv2.2")
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit removes the useless remove
mvpp2_bm_cookie_{build,pool_get} functions. All what
mvpp2_bm_cookie_build() was doing is compute a 32-bit value by
concatenating the pool number and the CPU number... only to get the pool
number re-extracted by mvpp2_bm_cookie_pool_get() later on.
Instead, just get the pool number directly from RX descriptor status,
and pass it to mvpp2_pool_refill() and mvpp2_rx_refill().
This has the added benefit of dropping a smp_processor_id() call in a
migration-enabled context, which is wrong, and is the original
motivation for making this change.
Fixes: 3f518509de ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvpp22_port_mii_set() function was added by 2697582144, but the
function directly returns without doing anything. This return was used
when debugging and wasn't removed before sending the patch. Fix this.
Fixes: 2697582144 ("net: mvpp2: handle misc PPv2.1/PPv2.2 differences")
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A string which did not contain a data format specification should be put
into a sequence. Thus use the corresponding function "seq_puts".
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The script "checkpatch.pl" pointed information out like the following.
Comparison to NULL could be written "!skge->mem".
Thus fix the affected source code place.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
A string which did not contain a data format specification should be put
into a sequence. Thus use the corresponding function "seq_puts".
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
MIME-Version: 1.0
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: 8bit
The script “checkpatch.pl” pointed information out like the following.
Comparison to NULL could be written …
Thus fix the affected source code places.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Multiplications for the size determination of memory allocations
indicated that array data structures should be processed.
Thus use the corresponding function "kcalloc".
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The script "checkpatch.pl" pointed information out like the following.
Comparison to NULL could be written "txq->descs".
Thus fix the affected source code place.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adjust jump labels according to the Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adjust jump labels according to the Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adjust jump labels according to the Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adjust jump labels according to the Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the word "failed" in the string for three function calls.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adjust jump labels according to the Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The script "checkpatch.pl" pointed out that labels should not be indented.
Thus delete two horizontal tabs before the jump label "err_drop_frame"
in the function "mvpp2_rx".
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the specification of two data structures by pointer dereferences
as the parameter for the operator "sizeof" to make the corresponding size
determination a bit safer according to the Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the specification of data structures by references to
a local variable as the parameter for the operator "sizeof"
to make the corresponding size determination a bit safer.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the specification of a data structure by a pointer dereference
as the parameter for the operator "sizeof" to make the corresponding size
determination a bit safer according to the Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the specification of a data structure by a pointer dereference
as the parameter for the operator "sizeof" to make the corresponding size
determination a bit safer according to the Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the specification of a data structure by a pointer dereference
as the parameter for the operator "sizeof" to make the corresponding size
determination a bit safer according to the Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the specification of a data structure by a pointer dereference
as the parameter for the operator "sizeof" to make the corresponding size
determination a bit safer according to the Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the specification of two data structures by pointer dereferences
as the parameter for the operator "sizeof" to make the corresponding size
determination a bit safer according to the Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
* A multiplication for the size determination of a memory allocation
indicated that an array data structure should be processed.
Thus use the corresponding function "kmalloc_array".
This issue was detected by using the Coccinelle software.
* Replace the specification of a data structure by a pointer dereference
to make the corresponding size determination a bit safer according to
the Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
MIME-Version: 1.0
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: 8bit
The script “checkpatch.pl” pointed information out like the following.
Comparison to NULL could be written …
Thus fix the affected source code places.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
A multiplication for the size determination of a memory allocation
indicated that an array data structure should be processed.
Thus use the corresponding function "kmalloc_array".
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the specification of two data structures by pointer dereferences
as the parameter for the operator "sizeof" to make the corresponding size
determination a bit safer according to the Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
* A multiplication for the size determination of a memory allocation
indicated that an array data structure should be processed.
Thus use the corresponding function "devm_kmalloc_array".
This issue was detected by using the Coccinelle software.
* Replace the specification of a data type by a pointer dereference
to make the corresponding size determination a bit safer according to
the Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently, suspend/resume and WOL support are added into mvneta driver.
If we enable WOL, then we get some error as below on Marvell BG4CT
platforms during suspend:
[ 184.149723] dpm_run_callback(): mdio_bus_suspend+0x0/0x50 returns -16
[ 184.149727] PM: Device f7b62004.mdio-mi:00 failed to suspend: error -16
-16 means -EBUSY, phy_suspend() will return -EBUSY if it finds the
device has WOL enabled.
We fix this issue by properly setting the netdev's power.can_wakeup
and power.wakeup, i.e
1. in mvneta_mdio_probe(), call device_set_wakeup_capable() to set
power.can_wakeup if the phy support WOL.
2. in mvneta_ethtool_set_wol(), call device_set_wakeup_enable() to
set power.wakeup if WOL has been successfully enabled in phy.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow up to three clocks to be specified and enabled for the orion-mdio
interface, which are required for this interface to be accessible on
Armada 8k platforms.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disable the MDIO interrupt, falling back to polled mode, if the resource
size does not allow us to access the interrupt registers. All current
DT bindings use a size of 0x84, which allows access, but verifying it is
good practice.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pre-existing write to disable interrupts on the remove path happens
whether we have an interrupt or not. While this may seem to be a good
idea, this driver is re-used in many different implementations, some
where the binding only specifies four bytes of register space. This
access causes us to access registers outside of the binding.
Make it conditional on the interrupt being present, which is the same
condition used when enabling the interrupt in the first place.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the mvmdio driver has an interrupt, it enables the "done" interrupt
after requesting its interrupt handler. However, probe failure results
in the interrupt being left enabled. Disable it on the failure path.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
I found a bug by:
0. boot and start dhcp client
1. echo mem > /sys/power/state
2. resume back immediately
3. don't touch dhcp client to renew the lease
4. ping the gateway. No acks
Usually, after step2, the DHCP lease isn't expired, so in theory we
should resume all back. But in fact, it doesn't. It turns out
the rx mode isn't resumed correctly. This patch fixes it by adding
mvneta_set_rx_mode(dev) in the resume hook if interface is running.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
RGMII_RXID and RGMII_TX_ID share the same GMAC CTRL setting as RGMII
or RGMII_ID.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add basic support for handling suspend and resume.
Signed-off-by: Jane Li <jiel@marvell.com>
Reviewed-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the mvpp2 driver has been modified to accommodate the support
for PPv2.2, we can finally advertise this support by adding the
appropriate compatible string.
At the same time, we update the Kconfig description of the MVPP2 driver.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On PPv2.2, the streaming mappings can be anywhere in the first 40 bits
of the physical address space. However, for the coherent mappings, we
still need them to be in the first 32 bits of the address space,
because all BM pools share a single register to store the high 32 bits
of the BM pool address, which means all BM pools must be allocated in
the same 4GB memory area.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PPv2.2 variant of the network controller needs an additional
clock, the "MG clock" in order for the IP block to operate
properly. This commit adds support for this additional clock to the
driver, reworking as needed the error handling path.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In PPv2.1, we have a maximum of 8 RXQs per port, with a default of 4
RXQs per port, and we were assigning RXQs 0->3 to the first port, 4->7
to the second port, 8->11 to the third port, etc.
In PPv2.2, we have a maximum of 32 RXQs per port, and we must allocate
RXQs from the range of 32 RXQs available for each port. So port 0 must
use RXQs in the range 0->31, port 1 in the range 32->63, etc.
This commit adapts the mvpp2 to this difference between PPv2.1 and
PPv2.2:
- The constant definition MVPP2_MAX_RXQ is replaced by a new field
'max_port_rxqs' in 'struct mvpp2', which stores the maximum number of
RXQs per port. This field is initialized during ->probe() depending
on the IP version.
- MVPP2_RXQ_TOTAL_NUM is removed, and instead we calculate the total
number of RXQs by multiplying the number of ports by the maximum of
RXQs per port. This was anyway used in only one place.
- In mvpp2_port_probe(), the calculation of port->first_rxq is adjusted
to cope with the different allocation strategy between PPv2.1 and
PPv2.2. Due to this change, the 'next_first_rxq' argument of this
function is no longer needed and is removed.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit adjusts how the MVPP2_ISR_RXQ_GROUP_REG register is
configured, since it changed between PPv2.1 and PPv2.2.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PPv2.2 unit is connected to an AXI bus on Armada 7K/8K, so this
commit adds the necessary initialization of the AXI bridge.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit handles a few miscellaneous differences between PPv2.1 and
PPv2.2 in different areas, where code done for PPv2.1 doesn't apply for
PPv2.2 or needs to be adjusted (getting the MAC address, disabling PHY
polling, etc.).
Thanks to Russell King for providing the initial implementation of
mvpp22_port_mii_set().
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit adjusts the mvpp2 driver register mapping and access logic
to support PPv2.2, to handle a number of differences.
Due to how the registers are laid out in memory, the Device Tree binding
for the "reg" property is different:
- On PPv2.1, we had a first area for the packet processor
registers (common to all ports), and then one area per port.
- On PPv2.2, we have a first area for the packet processor
registers (common to all ports), and a second area for numerous other
registers, including a large number of per-port registers
In addition, on PPv2.2, the area for the common registers is split into
so-called "address spaces" of 64 KB each. They allow to access per-CPU
registers, where each CPU has its own copy of some registers. A few
other registers, which have a single copy, also need to be accessed from
those per-CPU windows if they are related to a per-CPU register. For
example:
- Writing to MVPP2_TXQ_NUM_REG selects a TX queue. This register is a
per-CPU register, it must be accessed from the current CPU register
window.
- Then a write to MVPP2_TXQ_PENDING_REG, MVPP2_TXQ_DESC_ADDR_REG (and
a few others) will affect the TX queue that was selected by the
write to MVPP2_TXQ_NUM_REG. It must be accessed from the same CPU
window as the write to the TXQ_NUM_REG.
Therefore, the ->base member of 'struct mvpp2' is replaced with a
->cpu_base[] array, each entry pointing to a mapping of the per-CPU
area. Since PPv2.1 doesn't have this concept of per-CPU windows, all
entries in ->cpu_base[] point to the same io-remapped area.
The existing mvpp2_read() and mvpp2_write() accessors use cpu_base[0],
they are used for registers for which the CPU window doesn't matter.
mvpp2_percpu_read() and mvpp2_percpu_write() are new accessors added to
access the registers for which the CPU window does matter, which is why
they take a "cpu" as argument.
The driver is then changed to use mvpp2_percpu_read() and
mvpp2_percpu_write() where it matters.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In PPv2.2, the MVPP2_RXQ_DESC_ADDR_REG and MVPP2_TXQ_DESC_ADDR_REG
registers have a slightly different layout, because they need to contain
a 64-bit address for the RX and TX descriptor arrays. This commit
adjusts those functions accordingly.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit modifies the mvpp2_defaults_set() function to not do the
loopback and FIFO threshold initialization, which are not needed for
PPv2.2.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MVPP2_RXQ_CONFIG_REG register has a slightly different layout
between PPv2.1 and PPv2.2, so this commit adapts the functions modifying
this register to accommodate for both the PPv2.1 and PPv2.2 cases.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit adjusts the allocation and freeing of BM pools to support
PPv2.2. This involves:
- Checking that the number of buffer pointers is a multiple of 16, as
required by the hardware.
- Adjusting the size of the DMA coherent area allocated for buffer
pointers. Indeed, PPv2.2 needs space for 2 pointers of 64-bits per
buffer, as opposed to 2 pointers of 32-bits per buffer in
PPv2.1. The size in bytes is now stored in a new field of the
mvpp2_bm_pool structure.
- On PPv2.2, getting the DMA address and cookie (used for the physical
address) of each buffer requires reading the
MVPP22_BM_ADDR_HIGH_ALLOC to get the high order bits of those
addresses. A new utility function mvpp2_bm_bufs_get_addrs() is
introduced to handle this.
- On PPv2.2, releasing a buffer requires writing the high order 32 bits
of the DMA address and cookie to MVPP22_BM_PHY_VIRT_HIGH_RLS_REG.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit adds the definition of the PPv2.2 HW descriptors, adjusts
the mvpp2_tx_desc and mvpp2_rx_desc structures accordingly, and adapts
the accessors to work on both PPv2.1 and PPv2.2.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the format of the HW descriptors is different between PPv2.1 and
PPv2.2, this commit introduces an intermediate union, with for now
only the PPv2.1 descriptors. The bulk of the driver code only
manipulates opaque mvpp2_tx_desc and mvpp2_rx_desc pointers, and the
descriptors can only be accessed and modified through the accessor
functions. A follow-up commit will add the descriptor definitions for
PPv2.2.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to the introduction for the support of PPv2.2 in the
mvpp2 driver, this commit adds a hw_version field to the struct
mvpp2, and uses the .data field of the DT match table to fill it in.
Having the MVPP21 and MVPP22 definitions available will allow to start
adding the necessary conditional code to support PPv2.2.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PPv2.2 IP has a different TX and RX descriptor layout compared to
PPv2.1. In order to prepare for the introduction of PPv2.2 support in
mvpp2, this commit adds accessors for the different fields of the TX
and RX descriptors, and changes the code to use them.
For now, the mvpp2_port argument passed to the accessors is not used,
but it will be used in follow-up to update the descriptor according to
the version of the IP being used.
Apart from the mechanical changes to use the newly introduced
accessors, a few other changes, needed to use the accessors, are made:
- The mvpp2_txq_inc_put() function now takes a mvpp2_port as first
argument, as it is needed to use the accessors.
- Similarly, the mvpp2_bm_cookie_build() gains a mvpp2_port first
argument, for the same reason.
- In mvpp2_rx_error(), instead of accessing the RX descriptor in each
case of the switch, we introduce a local variable to store the
packet size.
- In mvpp2_tx_frag_process() and mvpp2_tx() instead of accessing the
packet size from the TX descriptor, we use the actual value
available in the function, which is used to set the TX descriptor
packet size a few lines before.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RX descriptors of the PPv2 hardware allow to store several
information, amongst which:
- the DMA address of the buffer in which the data has been received
- a "cookie" field, left to the use of the driver, and not used by the
hardware
In the current implementation, the "cookie" field is used to store the
virtual address of the buffer, so that in the receive completion path,
we can easily get the virtual address of the buffer that corresponds to
a completed RX descriptors.
On PPv2.1, used on 32-bit platforms, those two fields are 32-bit wide,
which is enough to store a DMA address in the first field, and a virtual
address in the second field.
On PPv2.2, used on 64-bit platforms, these two fields have been extended
to 40 bits. While 40 bits is enough to store a DMA address (as long as
the DMA mask is 40 bits or lower), it is not enough to store a virtual
address. Therefore, the "cookie" field can no longer be used to store
the virtual address of the buffer.
However, as Russell King pointed out, the RX buffers are always
allocated in the kernel linear mapping, and therefore using
phys_to_virt() on the physical address of the RX buffer is possible and
correct.
Therefore, this commit changes the driver to use the "cookie" field to
store the physical address instead of the virtual
address. phys_to_virt() is used in the receive completion path to
retrieve the virtual address from the physical address.
It is obviously important to realize that the DMA address and physical
address are two different things, which is why we store both in the RX
descriptors. While those addresses may be identical in some situations,
it remains two distinct concepts, and both addresses should be handled
separately.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvpp2_txq_pend_desc_num_get() function only selects a TX queue, and
reads the number of pending descriptors. It is used in only one place,
in mvpp2_txq_clean(), where the TX queue has already been selected by a
write to MVPP2_TXQ_NUM_REG.
Therefore, this function is useless, and the caller can simply read the
value of the MVPP2_TXQ_PENDING_REG register instead.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This register is no longer used since commit edc660fa09 ("net: mvpp2:
replace TX coalescing interrupts with hrtimer").
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "buffer header" functionality is a functionality used by the
hardware to split an incoming packets over multiple BM buffers if they
are not large enough. However, the mvpp2 driver guarantees that a pool
of BM buffers has buffers with a size large enough to store MTU-sized
packets. Therefore, this functionality is completely unused, and the
code can be removed, and we should never get a descriptor with bit
MVPP2_RXD_BUF_HDR set.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As indicated by Russell King, the mvpp2 driver currently uses a lot
"phys" or "phys_addr" to store what really is a DMA address. This commit
clarifies this by using "dma" or "dma_addr" where appropriate.
This is especially important as we are going to introduce more changes
where the distinction between physical address and DMA address will be
key.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvpp2 is going to be extended to support the Marvell Armada 7K/8K
platform, which is ARM64. As a preparation to this work, this commit
enables building the mvpp2 driver on ARM64, by:
- Adjusting the Kconfig dependency
- Fixing the types used in the driver so that they are 32/64-bits
compliant. We use dma_addr_t for DMA addresses, and unsigned long
for virtual addresses.
It is worth mentioning that after this commit, the driver is for now
still only used on 32-bits platforms, and will only work on 32-bits
platforms.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit adapts the mvpp2 RX path to use the build_skb() method. Not
only build_skb() is now the recommended mechanism, but it also
simplifies the addition of support for the PPv2.2 variant.
Indeed, without build_skb(), we have to keep track for each RX
descriptor of the physical address of the packet buffer, and the virtual
address of the SKB. However, in PPv2.2 running on 64 bits platform,
there is not enough space in the descriptor to store the virtual address
of the SKB. So having to take care only of the address of the packet
buffer, and building the SKB upon reception helps in supporting PPv2.2.
The implementation is fairly straightforward:
- mvpp2_skb_alloc() is renamed to mvpp2_buf_alloc() and no longer
allocates a SKB. Instead, it allocates a buffer using the new
mvpp2_frag_alloc() function, with enough space for the data and SKB.
- The initialization of the RX buffers in mvpp2_bm_bufs_add() as well
as the refill of the RX buffers in mvpp2_rx_refill() is adjusted
accordingly.
- Finally, the mvpp2_rx() is modified to use build_skb().
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the MVPP2_PRS_RI_* definitions use the ~(value) syntax, which
doesn't compile nicely on 64-bit. Moreover, those definitions are in
fact unneeded, since they are always used in combination with a bit
mask that ensures only the appropriate bits are modified.
Therefore, such definitions should just be set to 0x0. In addition, as
suggested by Russell King, we change the _MASK definitions to also use
the BIT() macro so that it is clear they are related to the values
defined afterwards.
For example:
#define MVPP2_PRS_RI_L2_CAST_MASK 0x600
#define MVPP2_PRS_RI_L2_UCAST ~(BIT(9) | BIT(10))
#define MVPP2_PRS_RI_L2_MCAST BIT(9)
#define MVPP2_PRS_RI_L2_BCAST BIT(10)
becomes
#define MVPP2_PRS_RI_L2_CAST_MASK (BIT(9) | BIT(10))
#define MVPP2_PRS_RI_L2_UCAST 0x0
#define MVPP2_PRS_RI_L2_MCAST BIT(9)
#define MVPP2_PRS_RI_L2_BCAST BIT(10)
Because the values (MVPP2_PRS_RI_L2_UCAST, MVPP2_PRS_RI_L2_MCAST and
MVPP2_PRS_RI_L2_BCAST) are always applied with
MVPP2_PRS_RI_L2_CAST_MASK, and therefore there is no need for
MVPP2_PRS_RI_L2_UCAST to be defined as ~(BIT(9) | BIT(10)).
It fixes the following warnings when building the driver on a 64-bit
platform (which is not possible as of this commit, but will be enabled
in a follow-up commit):
drivers/net/ethernet/marvell/mvpp2.c: In function ‘mvpp2_prs_mac_promisc_set’:
drivers/net/ethernet/marvell/mvpp2.c:524:33: warning: large integer implicitly truncated to unsigned type [-Woverflow]
#define MVPP2_PRS_RI_L2_UCAST ~(BIT(9) | BIT(10))
^
drivers/net/ethernet/marvell/mvpp2.c:1459:33: note: in expansion of macro ‘MVPP2_PRS_RI_L2_UCAST’
mvpp2_prs_sram_ri_update(&pe, MVPP2_PRS_RI_L2_UCAST,
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvpp2_bm_bufs_add() currently creates a fake cookie by calling
mvpp2_bm_cookie_pool_set(), just to be able to call
mvpp2_pool_refill(). But all what mvpp2_pool_refill() does is extract
the pool ID from the cookie, and call mvpp2_bm_pool_put() with this ID.
Instead of doing this convoluted thing, just call mvpp2_bm_pool_put()
directly, since we have the BM pool ID.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit drops dead code from the mvpp2 driver. The 'in_use' and
'in_use_thresh' fields of 'struct mvpp2_bm_pool' are
incremented/decremented/initialized in various places. But they are only
used in one place:
if (is_recycle &&
(atomic_read(&bm_pool->in_use) < bm_pool->in_use_thresh))
return 0;
However 'is_recycle', passed as argument to mvpp2_rx_refill() is always
false. So in fact, this code is never reached, and the 'is_recycle'
argument is useless. So let's drop this code.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit remove a field of 'struct mvpp2_tx_queue' that is not used
anywhere.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvpp2_txq_bufs_free() function is called upon TX completion to DMA
unmap TX buffers, and free the corresponding SKBs. It gets the
references to the SKB to free and the DMA buffer to unmap from a per-CPU
txq_pcpu data structure.
However, the code currently increments the pointer to the next entry
before doing the DMA unmap and freeing the SKB. It does not cause any
visible problem because for a given SKB the TX completion is guaranteed
to take place on the CPU where the TX was started. However, it is much
more logical to increment the pointer to the next entry once the current
entry has been completely unmapped/released.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
When configuring the MVPP2_ISR_RX_THRESHOLD_REG with the RX coalescing
time threshold, we do not check for the maximum allowed value supported
by the driver, which means we might overflow and use a bogus value. This
commit adds a check for this situation, and if a value higher than what
is supported by the hardware is provided, then we use the maximum value
supported by the hardware.
In order to achieve this in a way that avoids overflow and rounding
errors, we introduce two utility functions mvpp2_usec_to_cycles() and
cycles_to_usec(). Many thanks to Russell King for suggesting this
implementation.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, mvpp2_rx_pkts_coal_set() does the following to avoid setting
a too large value for the RX coalescing by packet number:
val = (pkts & MVPP2_OCCUPIED_THRESH_MASK);
This means that if you set a value that is slightly higher the the
maximum number of packets, you in fact get a very low value. It makes a
lot more sense to simply check if the value is too high, and if it's too
high, limit it to the maximum possible value.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
As noticed by Russell King, the last argument of
mvpp2_rx_{pkts,time}_coal_set() is useless, since the packet/time
coalescing value is already stored in the 'struct mvpp2_rx_queue *'
passed as argument to these functions. So passing the packet/time value
as an additional argument, and setting them again in the mvpp2_rx_queue
structure is useles.
This commit therefore gets rid of this additional argument, assuming the
caller has assigned the appropriate value to rxq->pkts_coal or
rxq->time_coal before calling the respective functions.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
When TX descriptors are filled in, the buffer DMA address is split
between the tx_desc->buf_phys_addr field (high-order bits) and
tx_desc->packet_offset field (5 low-order bits).
However, when we re-calculate the DMA address from the TX descriptor in
mvpp2_txq_inc_put(), we do not take tx_desc->packet_offset into
account. This means that when the DMA address is not aligned on a 32
bytes boundary, we end up calling dma_unmap_single() with a DMA address
that was not the one returned by dma_map_single().
This inconsistency is detected by the kernel when DMA_API_DEBUG is
enabled. We fix this problem by properly calculating the DMA address in
mvpp2_txq_inc_put().
Cc: <stable@vger.kernel.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
if 'devm_kzalloc()' fails, we should release resources allocated so far,
just as done a few lines below.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvneta_eth_tool_ops is only used internally in mvneta driver, so
make it static.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/marvell/mvneta.c:2694:26: error: storage size of 'status' isn't known
drivers/net/ethernet/marvell/mvneta.c:2695:26: error: storage size of 'changed' isn't known
drivers/net/ethernet/marvell/mvneta.c:2695:9: error: variable 'changed' has initializer but incomplete type
drivers/net/ethernet/marvell/mvneta.c:2709:2: error: implicit declaration of function 'fixed_phy_update_state' [-Werror=implicit-function-declaration]
Add linux/phy_fixed.h to mvneta.c
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling phy_read_status() means that we may call into
genphy_read_status() which in turn will use genphy_update_link() which
can make changes to phydev->link outside of the state machine's state
transitions. This is an invalid behavior that is now caught as of
811a919135 ("phy state machine: failsafe leave invalid RUNNING state")
Since we don't have anything special, switch to the generic
phy_ethtool_get_link_ksettings() function now.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling phy_read_status() means that we may call into
genphy_read_status() which in turn will use genphy_update_link() which
can make changes to phydev->link outside of the state machine's state
transitions. This is an invalid behavior that is now caught as of
811a919135 ("phy state machine: failsafe leave invalid RUNNING state")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvneta itself does not support WOL, but the PHY might.
So pass the calls to the PHY
Signed-off-by: Jingju Hou <houjingj@marvell.com>
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use napi_complete_done() instead of __napi_complete() to :
1) Get support of gro_flush_timeout if opt-in
2) Not rearm interrupts for busy-polling users.
3) use standard NAPI API and get rid of napi_gro_flush()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
napi_complete_done() allows to opt-in for gro_flush_timeout,
added back in linux-3.19, commit 3b47d30396
("net: gro: add a per device gro flush timer")
This allows for more efficient GRO aggregation without
sacrifying latencies.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The network stack no longer uses the last_rx member of struct net_device
since the bonding driver switched to use its own private last_rx in
commit 9f24273837 ("bonding: use last_arp_rx in slave_last_rx()").
However, some drivers still (ab)use the field for their own purposes and
some driver just update it without actually using it.
Previously, there was an accompanying comment for the last_rx member
added in commit 4dc89133f4 ("net: add a comment on netdev->last_rx")
which asked drivers not to update is, unless really needed. However,
this commend was removed in commit f8ff080dac ("bonding: remove
useless updating of slave->dev->last_rx"), so some drivers added later
on still did update last_rx.
Remove all usage of last_rx and switch three drivers (sky2, atp and
smc91c92_cs) which actually read and write it to use their own private
copy in netdev_priv.
Compile-tested with allyesconfig and allmodconfig on x86 and arm.
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Mirko Lindner <mlindner@marvell.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
The callback set_link_ksettings no longer update the value
of advertising, as the struct ethtool_link_ksettings is
defined as const.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tests showed that when whole bandwidth is consumed, the latency for
various kind of traffic can reach high values. With saturated
link (e.g. with iperf from target to host) simple ping could take
significant amount of time. BQL proved to improve this situation
when implemented in mvneta driver. Measurements of ping latency
for 3 link speeds:
Speed | Latency w/o BQL | Latency with BQL
10 | 7-14 ms | 3.5 ms
100 | 2-12 ms | 0.6 ms
1000 | often timeout | up to 2ms
Decreasing latency as above result in sligt performance cost - 4kpps
(-1.4%) when pushing 64B packets via two bridged interfaces of Armada 38x.
For 1500B packets in the same setup, the mpstat tool showed +8% of
CPU occupation (default affinity, second CPU idle). Even though this
cost seems reasonable to take, considering other improvements.
This commit adds byte queue limit mechanism for the mvneta driver.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Basing on xmit_more flag of the skb, TX descriptors can be concatenated
before flushing. This commit delay Tx descriptor flush if the queue is
running and if there is more skb's to send.
A maximum allowed number of descriptors for flushing at once due to
MVNETA_TXQ_UPDATE_REG(q) reqisters limitation, is 255. Because of that
a new macro was added (MVNETA_TXQ_DEC_SENT_MASK) in order to ensure that
concatenated amount of descriptor does not exceed that value.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The network device operation for reading statistics is only called
in one place, and it ignores the return value. Having a structure
return value is potentially confusing because some future driver could
incorrectly assume that the return value was used.
Fix all drivers with ndo_get_stats64 to have a void function.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ktime_set(S,N) was required for the timespec storage type and is still
useful for situations where a Seconds and Nanoseconds part of a time value
needs to be converted. For anything where the Seconds argument is 0, this
is pointless and can be replaced with a simple assignment.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Since commit 71ce391dfb ("net: mvpp2: enable proper per-CPU TX
buffers unmapping"), we are not correctly DMA unmapping TX buffers for
fragments.
Indeed, the mvpp2_txq_inc_put() function only stores in the
txq_cpu->tx_buffs[] array the physical address of the buffer to be
DMA-unmapped when skb != NULL. In addition, when DMA-unmapping, we use
skb_headlen(skb) to get the size to be unmapped. Both of this works fine
for TX descriptors that are associated directly to a SKB, but not the
ones that are used for fragments, with a NULL pointer as skb:
- We have a NULL physical address when calling DMA unmap
- skb_headlen(skb) crashes because skb is NULL
This causes random crashes when fragments are used.
To solve this problem, we need to:
- Store the physical address of the buffer to be unmapped
unconditionally, regardless of whether it is tied to a SKB or not.
- Store the length of the buffer to be unmapped, which requires a new
field.
Instead of adding a third array to store the length of the buffer to be
unmapped, and as suggested by David Miller, this commit refactors the
tx_buffs[] and tx_skb[] arrays of 'struct mvpp2_txq_pcpu' into a
separate structure 'mvpp2_txq_pcpu_buf', to which a 'size' field is
added. Therefore, instead of having three arrays to allocate/free, we
have a single one, which also improve data locality, reducing the
impact on the CPU cache.
Fixes: 71ce391dfb ("net: mvpp2: enable proper per-CPU TX buffers unmapping")
Reported-by: Raphael G <raphael.glon@corp.ovh.com>
Cc: Raphael G <raphael.glon@corp.ovh.com>
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The build of sparc allmodconfig fails with the error:
"of_irq_to_resource" [drivers/net/ethernet/marvell/mv643xx_eth.ko]
undefined!
of_irq_to_resource() is defined when CONFIG_OF_IRQ is defined. And also
CONFIG_OF_IRQ can only be defined if CONFIG_IRQ is defined. So we can
safely use #if defined(CONFIG_OF_IRQ) in the code.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
We previously relied on GENERIC_ALLOCATOR to be selected by CONFIG_ARM,
but now we can compile-test the driver on other architectures that
don't select it:
drivers/net/built-in.o: In function `mvneta_bm_remove':
mvneta_bm.c:(.text+0x4ee35): undefined reference to `gen_pool_free'
This adds an explicit select for the part of the driver that has
the dependency.
Fixes: a0627f776a ("net: marvell: Allow drivers to be built with COMPILE_TEST")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
These two statements were not indented correctly so it's sort of
confusing.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Couple conflicts resolved here:
1) In the MACB driver, a bug fix to properly initialize the
RX tail pointer properly overlapped with some changes
to support variable sized rings.
2) In XGBE we had a "CONFIG_PM" --> "CONFIG_PM_SLEEP" fix
overlapping with a reorganization of the driver to support
ACPI, OF, as well as PCI variants of the chip.
3) In 'net' we had several probe error path bug fixes to the
stmmac driver, meanwhile a lot of this code was cleaned up
and reorganized in 'net-next'.
4) The cls_flower classifier obtained a helper function in
'net-next' called __fl_delete() and this overlapped with
Daniel Borkamann's bug fix to use RCU for object destruction
in 'net'. It also overlapped with Jiri's change to guard
the rhashtable_remove_fast() call with a check against
tc_skip_sw().
5) In mlx4, a revert bug fix in 'net' overlapped with some
unrelated changes in 'net-next'.
6) In geneve, a stale header pointer after pskb_expand_head()
bug fix in 'net' overlapped with a large reorganization of
the same code in 'net-next'. Since the 'net-next' code no
longer had the bug in question, there was nothing to do
other than to simply take the 'net-next' hunks.
Signed-off-by: David S. Miller <davem@davemloft.net>
Armada 3700 is a new ARMv8 SoC from Marvell using same network controller
as older Armada 370/38x/XP. There are however some differences that
needed taking into account when adding support for it:
* open default MBUS window to 4GB of DRAM - Armada 3700 SoC's Mbus
configuration for network controller has to be done on two levels:
global and per-port. The first one is inherited from the
bootloader. The latter can be opened in a default way, leaving
arbitration to the bus controller. Hence filled mbus_dram_target_info
structure is not needed
* make per-CPU operation optional - Recent patches adding RSS and XPS
support for Armada 38x/XP enabled per-CPU operation of the controller
by default. Contrary to older SoC's Armada 3700 SoC's network
controller is not capable of per-CPU processing due to interrupt lines'
connectivity. This patch restores non-per-CPU operation, which is now
optional and depends on neta_armada3700 flag value in mvneta_port
structure. In order not to complicate the code, separate interrupt
subroutine is implemented.
For now, on the Armada 3700, RSS is disabled as the current
implementation depend on the per cpu interrupts.
[gregory.clement@free-electrons.com: extract from a larger patch, replace
some ifdef and port to net-next for v4.10]
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Actually only the mvneta_bm support is not 64-bits compatible.
The mvneta code itself can run on 64-bits architecture.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prepare the mvneta driver in order to be usable on the 64 bits platform
such as the Armada 3700.
[gregory.clement@free-electrons.com]: this patch was extract from a larger
one to ease review and maintenance.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now the virtual address of the received buffer were stored in the
cookie field of the rx descriptor. However, this field is 32-bits only
which prevents to use the driver on a 64-bits architecture.
With this patch the virtual address is stored in an array not shared with
the hardware (no more need to use the DMA API). Thanks to this, it is
possible to use cache contrary to the access of the rx descriptor member.
The change is done in the swbm path only because the hwbm uses the cookie
field, this also means that currently the hwbm is not usable in 64-bits.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Reviewed-by: Jisheng Zhang <jszhang@marvell.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For HWBM all buffers are allocated in mvneta_bm_construct() and in runtime
they are put into descriptors by hardware. There is no need to fill them
at this point.
Suggested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For small frame reuse the phys_addr variable instead of accessing the
uncacheable value in the rx descriptor.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to deregister and free any fixed-link PHY registered using
of_phy_register_fixed_link() on probe errors and on driver unbind.
Fixes: 83895bedee ("net: mvneta: add support for fixed links")
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
udplite conflict is resolved by taking what 'net-next' did
which removed the backlog receive method assignment, since
it is no longer necessary.
Two entries were added to the non-priv ethtool operations
switch statement, one in 'net' and one in 'net-next, so
simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc-7 detects a short memset in mvpp2, introduced in the original
merge of the driver:
drivers/net/ethernet/marvell/mvpp2.c: In function 'mvpp2_cls_init':
drivers/net/ethernet/marvell/mvpp2.c:3296:2: error: 'memset' used with length equal to number of elements without multiplication by element size [-Werror=memset-elt-size]
The result seems to be that we write uninitialized data into the
flow table registers, although we did not get any warning about
that uninitialized data usage.
Using sizeof() lets us initialize then entire array instead.
Fixes: 3f518509de ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvneta driver advertises it supports IFF_UNICAST_FLT. However, it
actually does not. The hardware probably does support it, but there is
no code to configure the filter. As a quick and simple fix, remove the
flag. This will cause the core to fall back to promiscuous mode.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Fixes: b50b72de2f ("net: mvneta: enable features before registering the driver")
Signed-off-by: David S. Miller <davem@davemloft.net>
All conflicts were simple overlapping changes except perhaps
for the Thunder driver.
That driver has a change_mtu method explicitly for sending
a message to the hardware. If that fails it returns an
error.
Normally a driver doesn't need an ndo_change_mtu method becuase those
are usually just range changes, which are now handled generically.
But since this extra operation is needed in the Thunder driver, it has
to stay.
However, if the message send fails we have to restore the original
MTU before the change because the entire call chain expects that if
an error is thrown by ndo_change_mtu then the MTU did not change.
Therefore code is added to nicvf_change_mtu to remember the original
MTU, and to restore it upon nicvf_update_hw_max_frs() failue.
Signed-off-by: David S. Miller <davem@davemloft.net>
Both of these drivers won't work on 64-bit architectures unless they
are redesigned, since they store a virtual address pointer in a 32-bit
field of the descriptors:
drivers/net/ethernet/marvell/mvneta_bm.c: In function 'mvneta_bm_construct':
drivers/net/ethernet/marvell/mvneta_bm.c:103:16: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
drivers/net/ethernet/marvell/mvpp2.c: In function 'mvpp2_prs_vlan_init':
drivers/net/ethernet/marvell/mvpp2.c:2563:32: error: large integer implicitly truncated to unsigned type [-Werror=overflow]
This limits the COMPILE_TEST option for the two drivers again to
only build them on 32-bit. This seems nicer than shutting up the
warnings, in case we ever actually want to use them on 64-bit,
as the warnings indicate which parts of the driver are currently
broken there.
Fixes: a0627f776a ("net: marvell: Allow drivers to be built with COMPILE_TEST")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
All Marvell Ethernet drivers actually build fine with COMPILE_TEST with
a few warnings. We need to add a few HAS_DMA dependencies to fix linking
failures on problematic architectures like m32r.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sky2 frequently crashes during machine shutdown with:
sky2_get_stats+0x60/0x3d8 [sky2]
dev_get_stats+0x68/0xd8
rtnl_fill_stats+0x54/0x140
rtnl_fill_ifinfo+0x46c/0xc68
rtmsg_ifinfo_build_skb+0x7c/0xf0
rtmsg_ifinfo.part.22+0x3c/0x70
rtmsg_ifinfo+0x50/0x5c
netdev_state_change+0x4c/0x58
linkwatch_do_dev+0x50/0x88
__linkwatch_run_queue+0x104/0x1a4
linkwatch_event+0x30/0x3c
process_one_work+0x140/0x3e0
worker_thread+0x60/0x44c
kthread+0xdc/0xf0
ret_from_fork+0x10/0x50
This is caused by the sky2 being called after it has been shutdown.
A previous thread about this can be found here:
https://lkml.org/lkml/2016/4/12/410
An alternative fix is to assure that IFF_UP gets cleared by
calling dev_close() during shutdown. This is similar to what the
bnx2/tg3/xgene and maybe others are doing to assure that the driver
isn't being called following _shutdown().
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement ethtool::nway_reset using phy_ethtool_nway_reset. We are
already using dev->phydev all over the place so this comes for free.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement ethtool::nway_reset using phy_ethtool_nway_reset. We are
already using dev->phydev all over the place so this comes for free.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
