Now when udc-core supports binding to specific UDC by passing
its name via 'udc_name' member of usb_gadget_driver struct,
switch to this generic approach.
Tested-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
[rebased and fixed checkpatch issues]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Introduce new 'udc_name' member to usb_gadget_driver structure.
The 'udc_name' is a name of UDC that usb_gadget_driver should
be bound to. If udc_name is NULL, it will be bound to any
available UDC.
Tested-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
To prevent VBUS contention, the am335x MUSB phy senses VBUS first before
transitioning to host mode. However, for host-only mode, VBUS could be
directly tied to 5V power rail which could prevent MUSB transitions to
host mode.
This change receives dr_mode of the controller then bypass the first
VBUS sensing for host-only mode, so that MUSB can work in host mode
event if VBUS is tied to 5V.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The filename of am35x-phy-control.h is confusing. The header is used
by the am335x phy driver, but the filename refers to am35x. Even worse
there is indeed another device called am35x but it does not use this
header at all.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
As of commit 3d7608e4c1 ("ARM: shmobile: bockw: remove legacy
board file and config"), the Renesas R-Car (Gen1) USB PHY driver is no
longer used.
In theory it could still be used on R-Car Gen1 SoCs, but that would
require adding DT support to the driver. Instead, a new driver using the
generic PHY framework should be written, as was done for R-Car Gen2.
Remove the driver for good.
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Remove mach/irq.h from the list of included headers, there is no
compilation dependency on this include file, and the change is needed
to prevent a compilation failure, when mach/irq.h is removed.
Additionally remove other unneeded includes and sort out their order.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
struct usb_request have 3 flags which might be
important to know about during debug. This patch
shows each of the 3 flags as a single letter:
z -> for zero
s -> short not okay
i -> interrupt
A capital letter means the feature is enabled
while a lower case letter means it is disabled;
Thus 'zsI' indicates that a ZLP is not needed,
that we can accept a short packet and interrupt
for this request should be enabled.
Signed-off-by: Felipe Balbi <balbi@ti.com>
So far, dwc3 has always missed request->zero
handling for every endpoint. Let's implement
that so we can handle cases where transfer must
be finished with a ZLP.
Note that dwc3 is a little special. Even though
we're dealing with a ZLP, we still need a buffer
of wMaxPacketSize bytes; to hide that detail from
every gadget driver, we have a preallocated buffer
of 1024 bytes (biggest bulk size) to use (and
share) among all endpoints.
Reported-by: Ravi B <ravibabu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This file already uses pr_debug in a few places; this converts the
remaining printks.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In general it is wise to clear interrupts before processing them. If
you don't do that, you can get:
1. Interrupt happens
2. You look at system state and process interrupt
3. A new interrupt happens
4. You clear interrupt without processing it.
This patch was actually a first attempt to fix missing device insertions
as described in (usb: dwc2: host: Fix missing device insertions) and it
did solve some of the signal bouncing problems but not all of
them (which is why I submitted the other patch). Specifically, this
patch itself would sometimes change:
1. hardware sees connect
2. hardware sees disconnect
3. hardware sees connect
4. dwc2_port_intr() - clears connect interrupt
5. dwc2_handle_common_intr() - calls dwc2_hcd_disconnect()
...to:
1. hardware sees connect
2. hardware sees disconnect
3. dwc2_port_intr() - clears connect interrupt
4. hardware sees connect
5. dwc2_handle_common_intr() - calls dwc2_hcd_disconnect()
...but with different timing then sometimes we'd still miss cable
insertions.
In any case, though this patch doesn't fix any (known) problems, it
still seems wise as a general policy to clear interrupt before handling
them.
Note that for dwc2_handle_usb_port_intr(), instead of moving the clear
of PRTINT to the beginning of the function we remove it completely. The
only way to clear PRTINT is to clear the sources that set it in the
first place.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The dwc2_hcd_reset_func() function is only ever called directly by a
delayed work function. As such no locks are already held when the
function is called.
Doing a read-modify-write of CPU registers and setting fields in the
main hsotg data structure is a bad idea without locks. Let's add
locks.
The bug was found by code inspection only. It turns out that the
dwc2_hcd_reset_func() is only ever called today if the
"host_support_fs_ls_low_power" parameter is enabled and no code in
mainline enables that parameter. Thus no known issues in mainline are
fixed by this patch, but it's still probably wise to fix the function.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Some USB phy drivers have different handling for the controller in each
dr_mode. But the phy driver does not have visibility to the dr_mode of
the controller.
This adds an api to return the dr_mode of the controller which
associates the given phy node.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since now, we may have more than one request during the test, and
it is better we just quit once the error occurs instead of try
queueing further requests.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Suggested-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Reviewed-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since composite now overwrites bcdUSB for any gadget, remove
setting it in legacy gadgets. All legacy gadgets set 0x0200, the
same as the value additionally set by composite, so there is no
behaviour change.
Signed-off-by: Igor Kotrasinski <i.kotrasinsk@samsung.com>
Rebase onto current balbi/next
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In some cases, like when you've got a "Microsoft Wireless Keyboard 2000"
connected to dwc2 with a hub, expected that we'll get some transfer
errors sometimes. The controller is expected to try at least 3 times
before giving up. See figure "Figure A-67. Normal HS CSPLIT 3 Strikes
Smash" in the USB spec.
The dwc2 controller has a way to support this by using the "EC_MC"
field. The Raspberry Pi driver has logic for setting this right. See
fiq_fsm_queue_split_transaction() in their "dwc_otg_hcd.c". Let's use
the same logic.
After making this change, we no longer get dropped characters from the
above mentioned keyboard. Other devices on the same bus as the keyboard
also behave more properly.
Thanks for Julius Werner for the expert analysis and suggestions.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If you've got your interrupt signals bouncing a bit as you insert your
USB device, you might end up in a state when the device is connected but
the driver doesn't know it.
Specifically, the observed order is:
1. hardware sees connect
2. hardware sees disconnect
3. hardware sees connect
4. dwc2_port_intr() - clears connect interrupt
5. dwc2_handle_common_intr() - calls dwc2_hcd_disconnect()
Now you'll be stuck with the cable plugged in and no further interrupts
coming in but the driver will think we're disconnected.
We'll fix this by checking for the missing connect interrupt and
re-connecting after the disconnect is posted. We don't skip the
disconnect because if there is a transitory disconnect we really want to
de-enumerate and re-enumerate.
Notes:
1. As part of this change we add a "force" parameter to
dwc2_hcd_disconnect() so that when we're unloading the module we
avoid the new behavior. The need for this was pointed out by John
Youn.
2. The bit of code needed at the end of dwc2_hcd_disconnect() is
exactly the same bit of code from dwc2_port_intr(). To avoid
duplication, we refactor that code out into a new function
dwc2_hcd_connect().
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: John Youn <johnyoun@synopsys.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Support hisilicon,hi6220-usb for HiKey board
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Kmem caches help to get correct boundary for descriptor buffers
which need to be 512 bytes aligned for dwc2 controller.
Two kmem caches are needed for generic descriptors and for
hs isochronous descriptors which doesn't have same size.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Masks for HCDMA.CTD and HCDMA.DMAAddr are incorrect. As we always
start from first descriptor, no need to mask the address anyway.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use Streaming DMA mappings to handle cache coherency of frame list and
descriptor list. Cache are always flushed before controller access it
or before cpu access it.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
As descriptor dma mode does not support split transfers, it can't be
enabled for high speed devices. Add a core parameter to enable it for
full speed devices.
Ensure frame list and descriptor list are correctly freed during
disconnect.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
timeval is deprecated and not y2038 safe. Its size also changes according
to 32 bit/ 64 bit compilation. Replace it with 32 and 64 bit versions of
its individual fields, giving two ioctls with different code values.
The two ioctls are necessary to maintain the 32 bit and 64 bit userspace
compatibility with a 64/32 bit kernel.
Change unsigned to __u32 types for a definitive userspace interface.
This is in accordance with the psABI that the unsigned type is always
32 bits.
Also use motonic timer instead of real time to ensure positive delta
values.
Refactor usbtest_ioctl for readability to isolate the handling of the
testing timing measurement.
The official testusb userspace tool can be changed in a separate patch
to reflect the __u32 changes as well. It can use the usbtest_param_32
struct, since 32 bit seconds is long enough for test durations.
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Deepa Dinamani <deepa.kernel@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Remove unnecessary headers and variables.
Reviewed-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This function is shared between gadget functions, so this avoid unnecessary
duplicated code and potentially avoid memory leaks.
Reviewed-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This code is duplicated from f_midi_start_ep(midi, f, midi->out_ep).
Reviewed-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch modifies the ep.caps.type_{iso,bulk,int} setting and
the second argument of usb_ep_maxpacket_limit() using
the dparam.pipe_configs.
In the previous code, all the type_{iso,bulk,int} were set to true.
However, to avoid waste time for finding suitable pipe in usb_ep_enable(),
this driver should set correct type.
Also the second argument of usb_ep_maxpacket_limit() was set to 512
even if the pipe is isochronous or interrupt. So, this driver could
not bind a gadget driver like the g_audio driver.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The current code has info->bufnmb_last to calculate the BUFNMB bits of
PIPEBUF register. However, since the bufnmb_last is initialized in
the usbhs_pipe_init() only, this driver is possible to set unexpected
value to the register if usb_ep_{enable,disable}() are called many times.
So, this patch modifies the pipe configuration via struct
renesas_usbhs_driver_param to simplify the code. Also this patch changes:
- a double buffer configuration
- isochronous buffer size from 512 to 1024
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Process all completed urbs, if more urbs are complete by the time
driver processes completion interrupt.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When releasing a channel, increment hsotg->available_host_channels even
in case a periodic channel is released.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Isochronous descriptor is currently programmed for the frame
after the last descriptor was programmed.
If the last descriptor frame underrun, then current descriptor must
take this into account and must be programmed on the current frame + 1.
This overrun usually happens when system is loaded and dwc2 can't init
descriptor list in time.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This function allow comparing frame index used for
descriptor list which has 64 entries.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Prevent dwc2 driver from accessing channel while it frees it.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When completing non isoc xfer, dwc2_complete_non_isoc_xfer_ddma()
is relying on qtd->n_desc to process the corresponding number of
descriptors.
During the processing of these descriptors, qtd could be unlinked
and freed if xfer is done and urb is no more in progress.
In this case, dwc2_complete_non_isoc_xfer_ddma() will read again
qtd->n_desc whereas qtd has been freed. This will lead to unpredictable
results since qtd->n_desc is no more valid value.
To avoid this error, return a result != 0 in dwc2_process_non_isoc_desc(),
so that dwc2_complete_non_isoc_xfer_ddma() stops desc processing.
This has been seen with Slub debug enabled.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When a channel is halted because of urb dequeue during transfer
completion, no other qtds must be scheduled until halt is done.
Moreover, all in progress qtds must be given back.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Active bit must be enabled in all scheduled descriptors. Else transfer
never start.
Remove previous code which was not correctly configuring descriptors.
Active bit was set before calling dwc2_fill_host_isoc_dma_desc() which
is erasing dma_desc->status.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Increment qtd->isoc_frame_index_last before testing it, else below
check will never be true and IOC (Interrupt On Complete) bit for
last frame will never be set in descriptor status.
/* Set IOC for each descriptor corresponding to last frame of URB */
if (qtd->isoc_frame_index_last == qtd->urb->packet_count)
dma_desc->status |= HOST_DMA_IOC;
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Now the function of complicated_callback is not only used for iso
transfer, improve the error message to reflect it.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add queue depth for both iso and bulk transfer, with more queues, we
can do performance and stress test using sourcesink, and update g_zero
accordingly.
Reviewed-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Now that we have a generic dwc3-of-simple.c, we can
use that instead of maintaining dwc3-qcom.c which is
extremely similar.
Cc: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
For simple platforms which merely enable some clocks
and populate its children, we can use this generic
glue layer to avoid boilerplate code duplication.
For now this supports Qcom and Xilinx, but if we
find a way to add generic handling of regulators and
optional PHYs, we can absorb exynos as well.
Tested-by: Subbaraya Sundeep Bhatta <subbaraya.sundeep.bhatta@xilinx.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
It just ocurred to me that dwc3 already gives a
really hint of when a setup packet is pending and
that's the SETUP_PENDING TRB Status for EP0 IRQs.
Fix setup_packet_pending initialization based on
that. While at that, also make sure the comment in
gadget.c matches what code is doing.
Signed-off-by: Felipe Balbi <balbi@ti.com>
In dwc3_cleanup_done_reqs() we expect that all
iterations of our while (1) loop will find a valid
struct dwc3_request *. In case we don't, we're
dumping a WARN_ON_ONCE() splat so that people report
the failure.
This patch is a simple cleanup converting:
if (!req) {
WARN_ON_ONCE(1);
return 1;
}
to:
if (WARN_ON_ONCE(!req))
return 1;
which is a little easier to read.
Signed-off-by: Felipe Balbi <balbi@ti.com>
The last few dev_dbg() messages are converted to
tracepoints and we can finally ignore dev_dbg()
messages during debug sessions.
Signed-off-by: Felipe Balbi <balbi@ti.com>
The last few dev_dbg() messages are converted to
tracepoints and we can finally ignore dev_dbg()
messages during debug sessions.
Signed-off-by: Felipe Balbi <balbi@ti.com>
The last few dev_dbg() messages are converted to
tracepoints and we can finally ignore dev_dbg()
messages during debug sessions.
Signed-off-by: Felipe Balbi <balbi@ti.com>
By moving our sanity checks our internal function
__dwc3_gadget_ep_queue() we can simplify the
externally visible API while also making sure that
callers of __dwc3_gadget_ep_queue() also make use of
the same checks.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Some USB device / host controller combinations seem to have problems
with Link Power Management. For example, Steinar found that his xHCI
controller wouldn't handle bandwidth calculations correctly for two
video cards simultaneously when LPM was enabled, even though the bus
had plenty of bandwidth available.
This patch introduces a new quirk flag for devices that should remain
disabled for LPM, and creates quirk entries for Steinar's devices.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Steinar H. Gunderson <sgunderson@bigfoot.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to USB 2 specs ports need to signal resume for at least 20ms,
in practice even longer, before moving to U0 state.
Both host and devices can initiate resume.
On device initiated resume, a port status interrupt with the port in resume
state in issued. The interrupt handler tags a resume_done[port]
timestamp with current time + USB_RESUME_TIMEOUT, and kick roothub timer.
Root hub timer requests for port status, finds the port in resume state,
checks if resume_done[port] timestamp passed, and set port to U0 state.
On host initiated resume, current code sets the port to resume state,
sleep 20ms, and finally sets the port to U0 state. This should also
be changed to work in a similar way as the device initiated resume, with
timestamp tagging, but that is not yet tested and will be a separate
fix later.
There are a few issues with this approach
1. A host initiated resume will also generate a resume event. The event
handler will find the port in resume state, believe it's a device
initiated resume, and act accordingly.
2. A port status request might cut the resume signalling short if a
get_port_status request is handled during the host resume signalling.
The port will be found in resume state. The timestamp is not set leading
to time_after_eq(jiffies, timestamp) returning true, as timestamp = 0.
get_port_status will proceed with moving the port to U0.
3. If an error, or anything else happens to the port during device
initiated resume signalling it will leave all the device resume
parameters hanging uncleared, preventing further suspend, returning
-EBUSY, and cause the pm thread to busyloop trying to enter suspend.
Fix this by using the existing resuming_ports bitfield to indicate that
resume signalling timing is taken care of.
Check if the resume_done[port] is set before using it for timestamp
comparison, and also clear out any resume signalling related variables
if port is not in U0 or Resume state
This issue was discovered when a PM thread busylooped, trying to runtime
suspend the xhci USB 2 roothub on a Dell XPS
Cc: stable <stable@vger.kernel.org>
Reported-by: Daniel J Blueman <daniel@quora.org>
Tested-by: Daniel J Blueman <daniel@quora.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes redundant condition.
(length && length > 5) can be reduced to a single evaluation.
Tested by compilation only.
Caught by cppcheck.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
This patch removes redundant conditions.
(!A || (A && B)) is the same as (!A || B).
Tested by compilation only.
Caught by cppcheck.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Hopefully final set of fixes for v4.4 release cycle.
There's a fix for a regression on dwc3 caused by recent changes to how
transfers are started. We're not pre-starting interrupt endpoints
anymore.
A NULL pointer dereference fix for the MSM phy driver.
The UVC gadget got a minor fix for permissions to its configfs
attributes and, finally, two fixes for MUSB. A fix for PM runtime when
MUSB returns EPROBE_DEFER and a fix to actually return an error in case
we can't initialize a DMA engine.
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=o5zI
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v4.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for-v4.4-rc5
Hopefully final set of fixes for v4.4 release cycle.
There's a fix for a regression on dwc3 caused by recent changes to how
transfers are started. We're not pre-starting interrupt endpoints
anymore.
A NULL pointer dereference fix for the MSM phy driver.
The UVC gadget got a minor fix for permissions to its configfs
attributes and, finally, two fixes for MUSB. A fix for PM runtime when
MUSB returns EPROBE_DEFER and a fix to actually return an error in case
we can't initialize a DMA engine.
Signed-off-by: Felipe Balbi <balbi@ti.com>
76e0da3 "usb-gadget/uvc: use per-attribute show and store methods"
removed write permission for writeable attributes. Correct attribute
permissions.
Fixes: 76e0da3 "usb-gadget/uvc: use per-attribute show and store methods"
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If musb_init_controller fails at musb_platform_init, we have already
called pm_runtime_irq_safe for musb and that causes the pm runtime count
to be enabled for parent before the parent has completed initialization.
This causes pm to stop working as on unload nothing gets idled.
This issue can be reproduced at least with:
# modprobe omap2430
HS USB OTG: no transceiver configured
musb-hdrc musb-hdrc.0.auto: musb_init_controller failed with status -517
# modprobe phy-twl4030-usb
# rmmod omap2430
And after the steps above omap2430 will block deeper idle states on
omap3.
To fix this, let's not enable pm runtime until we need to and the
parent has been initialized. Note that this does not fix the issue of
PM being broken for musb during runtime.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
of_match_device could return NULL, and so cause a NULL pointer
dereference later.
Even if the probability of this case is very low, fixing it made
static analyzers happy.
Solving this with of_device_get_match_data made also code simplier.
Reported-by: coverity (CID 1324133)
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When assigning bool use true instead of 1. If declaring it as static and
it's false there's no need to initialize it, since static variables are
zeroed by default.
Caught by coccinelle.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The module should fail to load.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
CC: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It shouldn't matter how usbcore is compiled. As it is a subsystem,
the correct way to use nousb should be usbcore.nousb
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace BUG() with BUG_ON().
Caught by coccinelle.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Get rid of bool explicit comparisons.
Caught by Coccinelle.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently usb_port_resume waits for up to 2 seconds for CONNECT
status for SS devices only. This change will do the same thing for
non-SS devices even though the reason is a little different. This
will fix an issue where VBUS is turned off during system wide
"suspend to ram" and some 2.0 devices take greater than the current
max of 100ms to show connected after VBUS is enabled. This is most
commonly seen on hard drive based devices and USB3.0 devices plugged
into a 2.0 only port.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The interrupt handler, ohci_hcd_at91_overcurrent_irq may be called right
after registration. At that time, pdev->dev.platform_data is not yet set,
leading to a NULL pointer dereference.
Fixes: e4df92279f (USB: host: ohci-at91: merge loops in ohci_hcd_at91_drv_probe)
Reported-by: Peter Rosin <peda@axentia.se>
Tested-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: stable@vger.kernel.org # 4.3+
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
My recent Intel box is spewing these messages:
xhci_hcd 0000:00:14.0: xHCI Host Controller
xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 2
usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: xHCI Host Controller
usb usb2: Manufacturer: Linux 4.3.0+ xhci-hcd
usb usb2: SerialNumber: 0000:00:14.0
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 6 ports detected
usb: failed to peer usb2-port2 and usb1-port1 by location (usb2-port2:none) (usb1-port1:usb2-port1)
usb usb2-port2: failed to peer to usb1-port1 (-16)
usb: port power management may be unreliable
usb: failed to peer usb2-port3 and usb1-port1 by location (usb2-port3:none) (usb1-port1:usb2-port1)
usb usb2-port3: failed to peer to usb1-port1 (-16)
usb: failed to peer usb2-port5 and usb1-port1 by location (usb2-port5:none) (usb1-port1:usb2-port1)
usb usb2-port5: failed to peer to usb1-port1 (-16)
usb: failed to peer usb2-port6 and usb1-port1 by location (usb2-port6:none) (usb1-port1:usb2-port1)
usb usb2-port6: failed to peer to usb1-port1 (-16)
Diving into the acpi tables, I noticed the EHCI hub has 12 ports while the XHCI
hub has 8 ports. Most of those ports are of connect type USB_PORT_NOT_USED
(including port 1 of the EHCI hub).
Further the unused ports have location data initialized to 0x80000000.
Now each unused port on the xhci hub walks the port list and finds a matching
peer with port1 of the EHCI hub because the zero'd out group id bits falsely match.
After port1 of the XHCI hub, each following matching peer will generate the
above warning.
These warnings seem to be harmless for this scenario as I don't think it
matters that unused ports could not create a peer link.
The attached patch utilizes that assumption and just turns the pr_warn into
pr_debug to quiet things down.
Tested on my Intel box.
Signed-off-by: Don Zickus <dzickus@redhat.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
if a full speed hub connects to a high speed hub which
supports MTT, the MTT field of its slot context will be set
to 1 when xHCI driver setups an xHCI virtual device in
xhci_setup_addressable_virt_dev(); once usb core fetch its
hub descriptor, and need to update the xHC's internal data
structures for the device, the HUB field of its slot context
will be set to 1 too, meanwhile MTT is also set before,
this will cause configure endpoint command fail, so in the
case, we should clear MTT to 0 for full speed hub according
to section 6.2.2
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a memory leak because acpi_evaluate_dsm() actually returns an
object which the caller is supposed to release. Fix this by calling
ACPI_FREE() for the returned object (this expands to kfree() so passing
NULL there is fine as well).
While there correct indentation in !CONFIG_ACPI case.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: stable <stable@vger.kernel.org> # v4.2
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB3 LPM is default on in Linux kernel if both xHCI host controller
and the USB devices declare to be LPM-capable. Unfortunately, some
devices are known to work well with LPM disabled, but to be broken
if LPM is enabled, although it declares the LPM capability. Users
won't be able to use this kind of devices, until someone puts them
in the kernel blacklist and gets the kernel upgraded.
This patch adds a sysfs node to permit or forbit USB3 LPM U1 or U2
entry for a port. The settings apply to both before and after device
enumeration. Supported values are "0" - neither u1 nor u2 permitted,
"u1" - only u1 is permitted, "u2" - only u2 is permitted, "u1_u2" -
both u1 and u2 are permitted. With this interface, users can use an
LPM-unfriendly USB device on a released Linux kernel.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Zhuang Jin Can <jin.can.zhuang@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 655fe4effe ("usbcore: add sysfs support to xHCI usb3
hardware LPM") introduced usb3_hardware_lpm sysfs node. This
doesn't show the correct status of USB3 U1 and U2 LPM status.
This patch fixes this by replacing usb3_hardware_lpm with two
nodes, usb3_hardware_lpm_u1 (for U1) and usb3_hardware_lpm_u2
(for U2), and recording the U1/U2 LPM status in right places.
This patch should be back-ported to kernels as old as 4.3,
that contains Commit 655fe4effe ("usbcore: add sysfs support
to xHCI usb3 hardware LPM").
Cc: stable@vger.kernel.org
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch sets the AHBMODE to allow for posted data writes. This
results in higher performance.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Tested-by: Georgi Djakov <georgi.djakov@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch sets the AHBMODE to allow for posted data writes. This
results in higher performance.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
struct mon_bin_hdr allows for a 64-bit seconds timestamp. The code
currently uses 'struct timeval' to populate the timestamp in mon_bin_hdr,
which has a 32-bit seconds field and will overflow in year 2038 and beyond.
This patch replaces 'struct timeval' with 'struct timespec64' which is
y2038 safe. This patch is part of a larger attempt to remove instances
of struct timeval and other 32-bit timekeeping (time_t, struct timespec)
from the kernel.
Signed-off-by: Tina Ruchandani <ruchandani.tina@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
timeval is deprecated and not y2038 safe. Its size also changes according
to 32 bit/ 64 bit compilation. Replace it with 32 and 64 bit versions of
its individual fields, giving two ioctls with different code values.
The two ioctls are necessary to maintain the 32 bit and 64 bit userspace
compatibility with a 64/32 bit kernel.
Change unsigned to __u32 types for a definitive userspace interface.
This is in accordance with the psABI that the unsigned type is always
32 bits.
Also use motonic timer instead of real time to ensure positive delta
values.
Refactor usbtest_ioctl for readability to isolate the handling of the
testing timing measurement.
The official testusb userspace tool can be changed in a separate patch
to reflect the __u32 changes as well. It can use the usbtest_param_32
struct, since 32 bit seconds is long enough for test durations.
Signed-off-by: Deepa Dinamani <deepa.kernel@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
struct timeval' uses 32-bits for its seconds field and will overflow in
the year 2038 and beyond. This patch replaces the usage of 'struct timeval'
in mon_get_timestamp() with timespec64 which uses a 64-bit seconds field
and is y2038-safe. mon_get_timestamp() truncates the timestamp at 4096 seconds,
so the correctness of the code is not affected. This patch is part of a larger
attempt to remove instances of struct timeval and other 32-bit timekeeping
(time_t, struct timespec) from the kernel.
Signed-off-by: Tina Ruchandani <ruchandani.tina@gmail.com>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
So far we were using simple (legacy) GPIO functions & some poor logic to
control power. It got many drawbacks: we were ignoring OF flags
(GPIO_ACTIVE_LOW), we were not setting direction to output and we were
assuming gpio_request success all the time.
Fix it by switching to gpiod functions and adding appropriate checks.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_parse_ss_endpoint_companion() now decodes the burst multiplier
correctly in order to check that it's <= 3, but still uses the wrong
expression if warning that it's > 3.
Fixes: ff30cbc8da ("usb: Use the USB_SS_MULT() macro to get the ...")
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
qset_fill_page_list() do not check for dma mapping errors.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a USB 3.0 mass storage device is disconnected in transporting
state, storage device driver may handle it as a transport error and
reset the device by invoking usb_reset_and_verify_device()
and following could happen:
in usb_reset_and_verify_device():
udev->bos = NULL;
For U1/U2 enabled devices, driver will disable LPM, and in some
conditions:
from usb_unlocked_disable_lpm()
--> usb_disable_lpm()
--> usb_enable_lpm()
udev->bos->ss_cap->bU1devExitLat;
And it causes 'NULL pointer' and 'kernel panic':
[ 157.976257] Unable to handle kernel NULL pointer dereference
at virtual address 00000010
...
[ 158.026400] PC is at usb_enable_link_state+0x34/0x2e0
[ 158.031442] LR is at usb_enable_lpm+0x98/0xac
...
[ 158.137368] [<ffffffc0006a1cac>] usb_enable_link_state+0x34/0x2e0
[ 158.143451] [<ffffffc0006a1fec>] usb_enable_lpm+0x94/0xac
[ 158.148840] [<ffffffc0006a20e8>] usb_disable_lpm+0xa8/0xb4
...
[ 158.214954] Kernel panic - not syncing: Fatal exception
This commit moves 'udev->bos = NULL' behind usb_unlocked_disable_lpm()
to prevent from NULL pointer access.
Issue can be reproduced by following setup:
1) A SS pen drive behind a SS hub connected to the host.
2) Transporting data between the pen drive and the host.
3) Abruptly disconnect hub and pen drive from host.
4) With a chance it crashes.
Signed-off-by: Hans Yang <hansy@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usb_mon_operations structure is never modified, so declare it as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now the function of complicated_callback is not only used for iso
transfer, improve the error message to reflect it.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
for checking if a property is present or not,
of_property_read_bool is more appropriate than of_get_property()
Signed-off-by: Saurabh Sengar <saurabh.truth@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This function must be called with a spinlock held.
Memory can be allocated only with GFP_ATOMIC. Passing
a gfp_t argument is a waste.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use this macro to make the driver more readable.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dma_pool_destroy() function tests whether its argument is NULL
and then returns immediately. Thus the test around the calls is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
replace dma_pool_alloc and memset with a single call to dma_pool_zalloc
Signed-off-by: Saurabh Sengar <saurabh.truth@gmail.com>
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace the existing two extended capability parsing helper functions with
one called xhci_find_next_ext_cap().
The extended capabilities are read both in pci-quirks before xhci driver is
loaded, and inside the xhci driver when adding ports. The existing helpers
did not suit well for these cases and a lot of custom parsing code was
needed.
The new helper function simplifies these two cases a lot.
The motivation for this rework was that code to support xhci debug
capability needed to parse extended capabilities, and it included
yet another capability parsing helper specific for its needs. With
this solution it debug capability code can use this new helper as well
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't use dev_warn() for intened behaviour, use dev_dbg()
Rounding down the interval to the nearest power of 2 is required
by xhci specs.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There some vendor quirks for MTK xhci host controller:
1. It defines some extra SW scheduling parameters for HW
to minimize the scheduling effort for synchronous and
interrupt endpoints. The parameters are put into reseved
DWs of slot context and endpoint context.
2. Its IMODI unit for Interrupter Moderation register is
8 times as much as that defined in xHCI spec.
3. Its TDS in Normal TRB defines a number of packets that
remains to be transferred for a TD after processing all
Max packets in all previous TRBs.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Tested-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The R-Car H3 has two xHCI controllers. This SoC is compatible with
R-Car Gen2 SoCs, however this SoC doesn't need some specific registers
setting, and need a new firmware.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for R-Car M2-N (r8a7793) xHCI controller.
This SoC is compatible with R-Car H2 (r8a7790) and R-Car M2-W (r8a7791).
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch changes code to ease the addition of next generation SoCs.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a member "firmware_name" in struct xhci_plat_priv
to simplify the code to match specific firmware name.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds struct xhci_plat_priv to simplify the code to match
platform specific variables. For now, this patch adds a member "type"
in the structure.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds an xhci->priv field for private use by
XHCI platform drivers. Until now none of the platform drivers
has used this private space.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch cleanups the hcd private size to suitable size.
The previous code has "sizeof(struct xhci_hcd *)" in xhci_hc_driver
as hcd_priv_size and sizeof(struct xhci_hcd) in xhci_plat_overrides
or xhci_pci_overrides as extra_priv_size. However, the xhci driver
uses a "sizeof(struct xhcd_hcd)" memory space in each hcd
(main_hcd and shared_hcd) actually.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
use the variables defined for populating the port status and
port chage bits retuend by GetPortStatus request intead of
the hub class feature selectors.
The defines for hub class feature selectors are used for other purposes,
they work as port status and feature selectors are in the same order, and
set the same bits, but it makes the code very hard to follow
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a new warning message to ehci-hcd. The warning is
triggered whenever the driver finds that the hardware has set the
Active bit in a QH at a time when the driver expects the QH to be
completely idle. Such bugs have been observed by users in the past,
and since they can lead to serious problems (such as inability to
unlink an URB that never completes), it would be good to know about
them when they occur.
This won't fix these bugs; that's a bigger job for a later patch. But
success isn't guaranteed, since this depends on aspects of the
hardware which are not documented in the EHCI spec or for which the
spec's recommendations are clearly unworkable. It therefore seems
worthwhile to check for these bugs proactively.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Michael Reutman <mreutman@epiqsolutions.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch enhances the "async" debugfs file in ehci-hcd by printing
out several additional fields in the hardware-accessible data
structures. These fields are important for determining the hardware's
view of the async schedule, in particular, the addresses of the
current and next qTDs for each QH along with the start address of each
qTD's data buffer.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch improves the usbfs_snoop debugging facility by adding
messages for a couple of significant events which, up to now, have not
been logged. The events are reaping and discarding (i.e.,
cancelling) an URB. The debugging messages include the userspace
address of the URB being reaped or discarded.
The reaping messages have to be added in four places, in order to
handle blocking and non-blocking reaps in both normal and 32-bit
compatibility mode.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usbfs_snoop facility can be very useful for debugging problems
involving usbfs. However, it always prints out the entire contents of
every URB. When dealing with large quantities of data, this can be
less than helpful.
This patch ameliorates the situation by adding a module parameter to
usbcore for controlling the maximum number of bytes to print when
snooping an URB. This makes debugging much easier. For backward
compatibility, the default value is set unreasonably high.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The patch extends the family of SATA-to-USB JMicron adapters that need
FUA to be disabled and applies the same policy for uas driver.
See details in http://unix.stackexchange.com/questions/237204/
Signed-off-by: Dmitry Katsubo <dmitry.katsubo@gmail.com>
Tested-by: Dmitry Katsubo <dmitry.katsubo@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Like other buggy models that had their fixes [1], the touchscreen with
id 04f3:21b8 from ELAN Microelectronics needs the device-qualifier
quirk. Otherwise, it fails to respond, blocks the boot for a random
amount of time and pollutes dmesg with:
[ 2887.373196] usb 1-5: new full-speed USB device number 41 using xhci_hcd
[ 2889.502000] usb 1-5: unable to read config index 0 descriptor/start: -71
[ 2889.502005] usb 1-5: can't read configurations, error -71
[ 2889.654571] usb 1-5: new full-speed USB device number 42 using xhci_hcd
[ 2891.783438] usb 1-5: unable to read config index 0 descriptor/start: -71
[ 2891.783443] usb 1-5: can't read configurations, error -71
[1]: See commits c68929f, 876af5d, d749947, a32c99e and dc703ec.
Tested-by: Adrien Vergé <adrienverge@gmail.com>
Signed-off-by: Adrien Vergé <adrienverge@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some device-id fixes that remove a HID device from cp210x, and
adds support for another Infineon flash-loader device. The flash-loader
device presents itself as a CDC-ACM device even though it is clearly
not, so we need to blacklist it in the cdc-acm driver as well.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=JdcP
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.4-rc3
Here are some device-id fixes that remove a HID device from cp210x, and
adds support for another Infineon flash-loader device. The flash-loader
device presents itself as a CDC-ACM device even though it is clearly
not, so we need to blacklist it in the cdc-acm driver as well.
Signed-off-by: Johan Hovold <johan@kernel.org>
Here's our second round of fixes. Some of the bugs are pretty old like
the one on pxa27x suspend implementation.
The most important part is a randbuild warning fix on MUSB CPPI DMA
engine by Arnd, a couple fixes by Felipe Tonello on f_midi (first one
makes sure we only transmit on enabled ep IN while second plugs a memory
leak) and a NULL pointer dereference fix on renesas usbhs.
Note that we also have a new compatible string being added for the MXS
PHY.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=qfZS
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v4.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v4.4-rc3
Here's our second round of fixes. Some of the bugs are pretty old like
the one on pxa27x suspend implementation.
The most important part is a randbuild warning fix on MUSB CPPI DMA
engine by Arnd, a couple fixes by Felipe Tonello on f_midi (first one
makes sure we only transmit on enabled ep IN while second plugs a memory
leak) and a NULL pointer dereference fix on renesas usbhs.
Note that we also have a new compatible string being added for the MXS
PHY.
Because interrupt endpoints usually transmit such
small amounts of data, it seems pointless to prestart
transfers and try to get speed improvements. This
patch also sorts out a problem with CDC ECM function
where its notification endpoint gets stuck in busy
state and we continuously issue Update Transfer
commands.
Fixes: 8a1a9c9e45 ("usb: dwc3: gadget: start transfer on XFER_COMPLETE")
Signed-off-by: Felipe Balbi <balbi@ti.com>
Added tx_empty callback needed for generic wait-until-sent support.
Without this function, when the port is closed usbserial can't know that
there are still data in the chip's transmit FIFO. The chip gets disabled
and untransmitted data lost. When the actual byte count is reported by
tx-empty the close can be delayed until all data are sent.
Signed-off-by: Konstantin Shkolnyy <konstantin.shkolnyy@gmail.com>
[johan: modify tx_empty error handling ]
Signed-off-by: Johan Hovold <johan@kernel.org>
This allows to write
drm-$(CONFIG_AGP) += drm_agpsupport.o
without having to handle CONFIG_AGP=y vs. CONFIG_AGP=m. Only support
this syntax for modules, since built-in code depending on something
modular cannot work and init/Makefile actually relies on the current
semantics. There are a few drivers which adapted to the current
semantics out of necessity; these are fixed to also work when the
respective subsystem is modular.
Acked-by: Peter Chen <peter.chen@freescale.com> [chipidea]
Signed-off-by: Michal Marek <mmarek@suse.com>
For historic reasons, the tegra platform selects USB_ULPI from architecture
code, but that hasn't really made sense for a long time, as the only
user of that code is the Tegra EHCI driver that has its own Kconfig
symbol.
This removes the 'select' statements from mach-tegra and drivers/soc/tegra
and adds them with the device driver that actually needs them.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The flash loader has been seen on a Telit UE910 modem. The flash loader
is a bit special, it presents both an ACM and CDC Data interface but
only the latter is useful. Unless a magic string is sent to the device
it will disappear and the regular modem device appears instead.
Signed-off-by: Jonas Jonsson <jonas@ludd.ltu.se>
Tested-by: Daniele Palmas <dnlplm@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Some modems, such as the Telit UE910, are using an Infineon Flash Loader
utility. It has two interfaces, 2/2/0 (Abstract Modem) and 10/0/0 (CDC
Data). The latter can be used as a serial interface to upgrade the
firmware of the modem. However, that isn't possible when the cdc-acm
driver takes control of the device.
The following is an explanation of the behaviour by Daniele Palmas during
discussion on linux-usb.
"This is what happens when the device is turned on (without modifying
the drivers):
[155492.352031] usb 1-3: new high-speed USB device number 27 using ehci-pci
[155492.485429] usb 1-3: config 1 interface 0 altsetting 0 endpoint 0x81 has an invalid bInterval 255, changing to 11
[155492.485436] usb 1-3: New USB device found, idVendor=058b, idProduct=0041
[155492.485439] usb 1-3: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[155492.485952] cdc_acm 1-3:1.0: ttyACM0: USB ACM device
This is the flashing device that is caught by the cdc-acm driver. Once
the ttyACM appears, the application starts sending a magic string
(simple write on the file descriptor) to keep the device in flashing
mode. If this magic string is not properly received in a certain time
interval, the modem goes on in normal operative mode:
[155493.748094] usb 1-3: USB disconnect, device number 27
[155494.916025] usb 1-3: new high-speed USB device number 28 using ehci-pci
[155495.059978] usb 1-3: New USB device found, idVendor=1bc7, idProduct=0021
[155495.059983] usb 1-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[155495.059986] usb 1-3: Product: 6 CDC-ACM + 1 CDC-ECM
[155495.059989] usb 1-3: Manufacturer: Telit
[155495.059992] usb 1-3: SerialNumber: 359658044004697
[155495.138958] cdc_acm 1-3:1.0: ttyACM0: USB ACM device
[155495.140832] cdc_acm 1-3:1.2: ttyACM1: USB ACM device
[155495.142827] cdc_acm 1-3:1.4: ttyACM2: USB ACM device
[155495.144462] cdc_acm 1-3:1.6: ttyACM3: USB ACM device
[155495.145967] cdc_acm 1-3:1.8: ttyACM4: USB ACM device
[155495.147588] cdc_acm 1-3:1.10: ttyACM5: USB ACM device
[155495.154322] cdc_ether 1-3:1.12 wwan0: register 'cdc_ether' at usb-0000:00:1a.7-3, Mobile Broadband Network Device, 00:00:11:12:13:14
Using the cdc-acm driver, the string, though being sent in the same way
than using the usb-serial-simple driver (I can confirm that the data is
passing properly since I used an hw usb sniffer), does not make the
device to stay in flashing mode."
Signed-off-by: Jonas Jonsson <jonas@ludd.ltu.se>
Tested-by: Daniele Palmas <dnlplm@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
CP2110 ID (0x10c4, 0xea80) doesn't belong here because it's a HID
and completely different from CP210x devices.
Signed-off-by: Konstantin Shkolnyy <konstantin.shkolnyy@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
This patch make sure that all necessary members of dwc2_hsotg
are initialized before the irq handler is requested. So
the kernel oops triggered by dwc2_handle_common_intr has
been fixed.
dwc2 20980000.usb: Configuration mismatch. Forcing host mode
dwc2 20980000.usb: no platform data or transceiver defined
Unable to handle kernel paging request at virtual address cc860040
pgd = c0004000
[cc860040] *pgd=0b41e811, *pte=00000000, *ppte=00000000
Internal error: Oops: 7 [#1] ARM
CPU: 0 PID: 1 Comm: swapper Not tainted 4.3.0-rc3+ #19
Hardware name: BCM2835
task: cb494000 ti: cb4d0000 task.ti: cb4d0000
PC is at dwc2_is_controller_alive+0x18/0x34
LR is at dwc2_handle_common_intr+0x24/0xb60
Acked-by: John Youn <johnyoun@synopsys.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
It is not permitted to set task state before lock. usblp_wwait sets
the state to TASK_INTERRUPTIBLE and calls mutex_lock_interruptible.
Upon return from that function, the state will be TASK_RUNNING again.
This is clearly a bug and a warning is generated with LOCKDEP too:
WARNING: CPU: 1 PID: 5109 at kernel/sched/core.c:7404 __might_sleep+0x7d/0x90()
do not call blocking ops when !TASK_RUNNING; state=1 set at [<ffffffffa0c588d0>] usblp_wwait+0xa0/0x310 [usblp]
Modules linked in: ...
CPU: 1 PID: 5109 Comm: captmon Tainted: G W 4.2.5-0.gef2823b-default #1
Hardware name: LENOVO 23252SG/23252SG, BIOS G2ET33WW (1.13 ) 07/24/2012
ffffffff81a4edce ffff880236ec7ba8 ffffffff81716651 0000000000000000
ffff880236ec7bf8 ffff880236ec7be8 ffffffff8106e146 0000000000000282
ffffffff81a50119 000000000000028b 0000000000000000 ffff8802dab7c508
Call Trace:
...
[<ffffffff8106e1c6>] warn_slowpath_fmt+0x46/0x50
[<ffffffff8109a8bd>] __might_sleep+0x7d/0x90
[<ffffffff8171b20f>] mutex_lock_interruptible_nested+0x2f/0x4b0
[<ffffffffa0c588fc>] usblp_wwait+0xcc/0x310 [usblp]
[<ffffffffa0c58bb2>] usblp_write+0x72/0x350 [usblp]
[<ffffffff8121ed98>] __vfs_write+0x28/0xf0
...
Commit 7f477358e2 (usblp: Implement the
ENOSPC convention) moved the set prior locking. So move it back after
the lock.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Fixes: 7f477358e2 ("usblp: Implement the ENOSPC convention")
Acked-By: Pete Zaitcev <zaitcev@yahoo.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When choose randconfig for kernel build, it reports below warning:
"warning: (USB_OTG_FSM && FSL_USB2_OTG && USB_MV_OTG) selects USB_OTG
which has unmet direct dependencies (USB_SUPPORT && USB && PM)"
In fact, USB_OTG is visible symbol and depends on PM, so the driver
needs to depend on it to reduce dependency problem.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Cc: Felipe Balbi <balbi@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thomas reports
"
4gsystems sells two total different LTE-surfsticks under the same name.
..
The newer version of XS Stick W100 is from "omega"
..
Under windows the driver switches to the same ID, and uses MI03\6 for
network and MI01\6 for modem.
..
echo "1c9e 9b01" > /sys/bus/usb/drivers/qmi_wwan/new_id
echo "1c9e 9b01" > /sys/bus/usb-serial/drivers/option1/new_id
T: Bus=01 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#= 4 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1c9e ProdID=9b01 Rev=02.32
S: Manufacturer=USB Modem
S: Product=USB Modem
S: SerialNumber=
C: #Ifs= 5 Cfg#= 1 Atr=80 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I: If#= 4 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
Now all important things are there:
wwp0s29f7u2i3 (net), ttyUSB2 (at), cdc-wdm0 (qmi), ttyUSB1 (at)
There is also ttyUSB0, but it is not usable, at least not for at.
The device works well with qmi and ModemManager-NetworkManager.
"
Reported-by: Thomas Schäfer <tschaefer@t-online.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some new device ids, support for an odd qcserial Gobi interface
layout and a fix for the qcserial Huawei interface layout.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=YaM3
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.4-rc2
Here are some new device ids, support for an odd qcserial Gobi interface
layout and a fix for the qcserial Huawei interface layout.
Signed-off-by: Johan Hovold <johan@kernel.org>
Add "fsl,imx6ul-usbphy" compatible string for iMX6ul usb phy
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fixes a memory leak that occurs when an endpoint fails to enqueue
the request. If that happens the complete function will never be called, thus
never freeing the request.
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This makes sure f_midi doesn't try to enqueue data when the IN endpoint is
disabled, ie, USB cable is disconnected.
Reviewed-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fixes commit 09a75e8577
("usb: dwc2: refactor common low-level hw code to platform.c")
The above commit consolidated the low-level phy access into a common
location. This change made the otg clk a requirement and broke some
platforms when it was moved into platform.c.
So make clk handling optional again.
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Fixes: 09a75e8577 ("usb: dwc2: refactor common low-level hw code to platform.c")
Signed-off-by: Felipe Balbi <balbi@ti.com>
When searching for PHYs, any error was treated as if the PHY did not
exist or was not specified. Thus the probe function did not
correctly return error conditions such as -EPROBE_DEFER.
Fixed so that only a non-existing PHY is ignored and any other error
is returned.
Acked-by: Eric Anholt <eric@anholt.net>
Reported-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fixes commit 09a75e8577
("usb: dwc2: refactor common low-level hw code to platform.c")
The above commit consolidated the low-level phy access into a common
location. This change introduced a check from the gadget requiring
that a PHY is specified. This requirement never existed on the host
side and broke some platforms when it was moved into platform.c.
The gadget doesn't require the PHY either so remove the check.
Acked-by: Eric Anholt <eric@anholt.net>
Reported-by: Stefan Wahren <info@lategoodbye.de>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Fixes: 09a75e8577 ("usb: dwc2: refactor common low-level hw code to platform.c")
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fixes an issue that NULL pointer dereference happens when
a gadget driver calls usb_ep_dequeue() for ep0 after disconnected
a usb cable. This is because that usbhsg_try_stop() will call
usbhsg_ep_disable(&dcp->ep) when a usb cable is disconnected and
the pipe of dcp (ep0) is set to NULL.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When choose randconfig for kernel build, it reports below warning:
"warning: (USB_OTG_FSM && FSL_USB2_OTG && USB_MV_OTG) selects USB_OTG
which has unmet direct dependencies (USB_SUPPORT && USB && PM)"
In fact, USB_OTG is visible symbol and depends on PM, so the driver
needs to depend on it to reduce dependency problem.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Cc: Felipe Balbi <balbi@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
pxa27x disconnects pullups on suspend but doesn't
notify the gadget driver about it, so gadget driver
can't disable the endpoints it was using.
This causes problems on resume because gadget core
will think endpoints are still enabled and just
ignore the following usb_ep_enable().
Fix this problem by calling
gadget_driver->disconnect().
Cc: <stable@vger.kernel.org> # v3.10+
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Felipe Balbi <balbi@ti.com>
use safe copy_*_user instead of unsafe __copy_*_user
functions when accessing userland memory.
Signed-off-by: Daniel Walter <dwalter@sigma-star.at>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The CPPI-4.1 driver selects TI_CPPI41, which is a dmaengine
driver and that may not be available when CONFIG_DMADEVICES
is not set:
warning: (USB_TI_CPPI41_DMA) selects TI_CPPI41 which has unmet direct dependencies (DMADEVICES && ARCH_OMAP)
This adds an extra dependency to avoid generating warnings in randconfig
builds. Ideally we'd remove the 'select' statement, but that has the
potential to break defconfig files.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 411dd19c68 ("usb: musb: Kconfig: Select the DMA driver if DMA mode of MUSB is enabled")
Signed-off-by: Felipe Balbi <balbi@ti.com>
Clear device initiated resume variables once device is fully up and running
in U0 state.
Resume needs to be signaled for 20ms for usb2 devices before they can be
moved to U0 state.
An interrupt is triggered if a device initiates resume. As we handle the
event in interrupt context we can not sleep for 20ms, so we instead set
a resume flag, a timestamp, and start the roothub polling.
The roothub code will later move the port to U0 when it finds a port in
resume state with the resume flag set, and timestamp passed by 20ms.
A host initiated resume is however not done in interrupt context, and
host initiated resume code will directly signal resume, wait 20ms and then
move the port to U0.
These two codepaths can race, if we are in the middle of a host initated
resume, while sleeping for 20ms, we may handle a port event and find the
port in resume state. The port event handling code will assume the resume
was device initiated and set the resume flag and timestamp.
Root hub code will however not catch the port in resume state again as the
host initated resume code has already moved the port to U0.
The resume flag and timestamp will remain set for this port preventing port
from suspending again (LPM setting port to U3)
Fix this for now by always clearing the device initated resume parameters
once port is in U0
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Function ep_ring_is_processing() checks the dequeue pointer
in endpoint context to know whether an endpoint is busy with
processing TRBs. This is not correct since dequeue pointer
field in an endpoint context is only valid when the endpoint
is in Halted or Stopped states. This buggy code causes audio
noise when playing sound with USB headset connected to host
controllers which support CFC (one of xhci 1.1 features).
This patch should exist in stable kernel since v4.3.
Reported-and-tested-by: YD Tseng <yd_tseng@asmedia.com.tw>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Cc: stable <stable@vger.kernel.org> # v4.3
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Existing Intel xHCI controllers require a delay of 1 mS,
after setting the CMD_RESET bit in command register, before
accessing any HC registers. This allows the HC to complete
the reset operation and be ready for HC register access.
Without this delay, the subsequent HC register access,
may result in a system hang, very rarely.
Verified CherryView / Braswell platforms go through over
5000 warm reboot cycles (which was not possible without
this patch), without any xHCI reset hang.
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Tested-by: Joe Lawrence <joe.lawrence@stratus.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
of_match_device could return NULL, and so cause a NULL pointer
dereference later.
Reported-by: coverity (CID 1324138)
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
of_match_device could return NULL, and so cause a NULL pointer
dereference later. Renaming tmp_dev to of_id (like all others do) in the
process.
Reported-by: coverity (CID 1324135)
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
This patch is to support load and unload gadget driver in full OTG mode.
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Tested-by: Jiada Wang <jiada_wang@mentor.com>
Cc: <stable@vger.kernel.org> #v4.0+
Since the ci->role will be set after the host role start is complete, there
will be nobody cared irq during start host if usb irq enabled. This error
can be reproduced on i.mx6 sololite EVK board by:
1. disable otg id irq(IDIE) and disable all real otg properties of usbotg1
in dts.
2. boot up the board with ID cable and usb device connected.
3. echo gadget > /sys/kernel/debug/ci_hdrc.0/role
4. echo host > /sys/kernel/debug/ci_hdrc.0/role
5. irq 212: nobody cared.
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Some i.mx platforms need three clocks to let controller work, but
others only need one, refine clock operation to adapt for all
platforms, it fixes a regression found at i.mx27.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Cc: <stable@vger.kernel.org> #v4.1+
Following changes that appeared in lk 4.0.0, the gadget udc driver for
some ARM based Atmel SoCs (e.g. at91sam9x5 and sama5d3 families)
incorrectly deduced full-speed USB link speed even when the hardware
had negotiated a high-speed link. The fix is to make sure that the
UDPHS Interrupt Enable Register value does not mask the SPEED bit
in the Interrupt Status Register.
For a mass storage gadget this problem lead to failures when the host
had a USB 3 port with the xhci_hcd driver. If the host was a USB 2
port using the ehci_hcd driver then the mass storage gadget worked
(but probably at a lower speed than it should have).
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: <stable@vger.kernel.org> #4.0+
Fixes: 9870d895ad ("usb: atmel_usba_udc: Mask status with enabled irqs")
Signed-off-by: Felipe Balbi <balbi@ti.com>
Change the permission of usb_dma parameter so it can
be used for runtime debug without reboot.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
of_match_device could return NULL, and so cause a NULL pointer
dereference later.
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In some SoCs, dwc3 is implemented as a USB2.0 only
core, meaning that it can't ever achieve SuperSpeed.
Currect driver always sets gadget.max_speed to
USB_SPEED_SUPER unconditionally. This can causes
issues to some Host stacks where the host will issue
a GetBOS() request and we will reply with a BOS
containing Superspeed Capability Descriptor.
At least Windows seems to be upset by this fact and
prints a warning that we should connect $this device
to another port.
[ balbi@ti.com : rewrote entire commit, including
source code comment to make a lot clearer what the
problem is ]
Cc: <stable@vger.kernel.org>
Signed-off-by: Ben McCauley <ben.mccauley@garmin.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Here are a few changes in musb_h_tx_flush_fifo().
- It has been observed that sometimes (if not always) musb is unable
to flush tx fifo during urb dequeue when disconnect a device. But
it seems to be harmless, since the tx fifo flush is done again in
musb_ep_program() when re-use the hw_ep.
But the WARN() floods the console in the case when multiple tx urbs
are queued, so change it to dev_WARN_ONCE().
- applications could queue up many tx urbs, then the 1ms delay could
causes minutes of delay in device disconnect. So remove it to get
better user experience. The 1ms delay does not help the flushing
anyway.
- cleanup the debug code - related to lastcsr.
----
Note: The tx fifo flush issue has been observed during device disconnect
on AM335x.
To reproduce the issue, ensure tx urb(s) are queued when unplug the usb
device which is connected to AM335x usb host port.
I found using a usb-ethernet device and running iperf (client on AM335x)
has very high chance to trigger the problem.
Better to turn on dev_dbg() in musb_cleanup_urb() with CPPI enabled to
see the issue when aborting the tx channel.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In commit 734643dfbd ("usb: dwc2: host: add flag to reflect bus
state") we changed dwc2_port_suspend() not to set the lx_state
anymore (instead it sets the new bus_suspended variable). This
introduced a bug where we would fail to detect device insertions if:
1. Plug empty hub into dwc2
2. Plug USB flash drive into the empty hub.
3. Wait a few seconds
4. Unplug USB flash drive
5. Less than 2 seconds after step 4, plug the USB flash drive in again.
The dwc2_hcd_rem_wakeup() function should have been changed to look at
the new bus_suspended variable.
Let's fix it. Since commit b46146d59f ("usb: dwc2: host: resume root
hub on remote wakeup") talks about needing the root hub resumed if the
bus was suspended, we'll include it in our test.
It appears that the "port_l1_change" should only be set to 1 if we were
in DWC2_L1 (the driver currently never sets this), so we'll update the
former "else" case based on this test.
Fixes: 734643dfbd ("usb: dwc2: host: add flag to reflect bus state")
Acked-by: John Youn <johnyoun@synopsys.com>
Tested-by: Gregory Herrero <gregory.herrero@intel.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The comment for ahbcfg for rk3066 parameters (also used for rk3288)
claimed that ahbcfg was INCR16, but it wasn't. Since the bits weren't
shifted properly, the 0x7 ended up being masked and we ended up
programming 0x3 for the HBstLen. Let's set it to INCR16 properly.
As per Wu Liang Feng at Rockchip this may increase transmission
efficiency. I did blackbox tests with writing 0s to a USB-based SD
reader (forcefully capping CPU Freq to try to measure efficiency):
cd /sys/devices/system/cpu/cpu0/cpufreq
echo userspace > scaling_governor
echo 126000 > scaling_setspeed
for i in $(seq 10); do
dd if=/dev/zero of=/dev/sdb bs=1M count=750
done
With the above tests I found that speeds went from ~15MB/s to ~18MB/s.
Note that most other tests I did (including reading from the same USB
reader) didn't show any difference in performance.
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: John Youn <johnyoun@synopsys.com>
Reviewed-by: Liangfeng Wu <wulf@rock-chips.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The DEVICE_HWI type was added under the faulty assumption that Huawei
devices based on Qualcomm chipsets and firmware use the static USB
interface numbering known from Gobi devices. But this model does
not apply to Huawei devices like the HP branded lt4112 (Huawei me906e).
Huawei firmwares will dynamically assign interface numbers. Functions
are renumbered when the firmware is reconfigured.
Fix by changing the DEVICE_HWI type to use a simplified version
of Huawei's subclass + protocol scheme: Blacklisting known network
interface combinations and assuming the rest are serial.
Reported-and-tested-by: Muri Nicanor <muri+libqmi@immerda.ch>
Tested-by: Martin Hauke <mardnh@gmx.de>
Cc: <stable@vger.kernel.org>
Fixes: e7181d005e ("USB: qcserial: Add support for HP lt4112 LTE/HSPA+ Gobi 4G Modem")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Johan Hovold <johan@kernel.org>
otg_dev->extcon was referenced before otg_dev was initialized. Fix.
Cc: <stable@vger.kernel.org> # v4.3
Fixes: a2fd242324 ("usb: phy: omap-otg: Replace deprecated API of extcon")
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There is a bit of a mess in the order of arguments to the ulpi write
callback. There is
int ulpi_write(struct ulpi *ulpi, u8 addr, u8 val)
in drivers/usb/common/ulpi.c;
struct usb_phy_io_ops {
...
int (*write)(struct usb_phy *x, u32 val, u32 reg);
}
in include/linux/usb/phy.h.
The callback registered by the musb driver has to comply to the latter,
but up to now had "offset" first which effectively made the function
broken for correct users. So flip the order and while at it also
switch to the parameter names of struct usb_phy_io_ops's write.
Fixes: ffb865b1e4 ("usb: musb: add ulpi access operations")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The Honeywell HGI80 is a wireless interface to the evohome connected
thermostat. It uses a TI 3410 USB-serial port.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Also known as Verizon U620L.
The device is modeswitched from 1410:9020 to 1410:9022 by selecting the
4th USB configuration:
$ sudo usb_modeswitch –v 0x1410 –p 0x9020 –u 4
This configuration provides a ECM interface as well as TTYs ('Enterprise
Mode' according to the U620 Linux integration guide).
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
It seems like this device has same vendor and product IDs as G2K
devices, but it has different number of interfaces(4 vs 5) and also
different interface layout which makes it currently unusable:
usbcore: registered new interface driver qcserial
usbserial: USB Serial support registered for Qualcomm USB modem
usb 2-1.2: unknown number of interfaces: 5
lsusb output:
Bus 002 Device 003: ID 05c6:9215 Qualcomm, Inc. Acer Gobi 2000 Wireless
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x05c6 Qualcomm, Inc.
idProduct 0x9215 Acer Gobi 2000 Wireless Modem
bcdDevice 2.32
iManufacturer 1 Quectel
iProduct 2 Quectel LTE Module
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 209
bNumInterfaces 5
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xa0
(Bus Powered)
Remote Wakeup
MaxPower 500mA
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Cc: stable <stable@vger.kernel.org>
[johan: rename define and add comment ]
Signed-off-by: Johan Hovold <johan@kernel.org>
Add helper to access line-control register in order to work around a
cp2108 GET_LINE_CTL bug.
cp2108 GET_LINE_CTL returns the 16-bit value with the 2 bytes swapped.
However, SET_LINE_CTL functions properly. When the driver tries to modify
the register, it reads it, modifies some bits and writes back. Because the
read bytes were swapped, this often results in an invalid value to be
written. In turn, this causes cp2108 respond with a stall. The stall
sometimes doesn't clear properly and cp2108 starts responding to following
valid commands also with stalls, effectively failing.
Signed-off-by: Konstantin Shkolnyy <konstantin.shkolnyy@gmail.com>
[johan: amend commit message, modify probe error handling ]
Signed-off-by: Johan Hovold <johan@kernel.org>
This change is preparation for implementing a cp2108 bug workaround.
The workaround requires storing some private data. Right now the data is
attached to the USB interface and allocated in the attach() callback.
The bug detection requires USB I/O which is done easier from port_probe()
callback rather than attach(). Since the USB access functions take port
as a parameter, and since the private data is used exclusively by these
functions, it can be allocated in port_probe(). Also, all cp210x devices
have exactly 1 port per USB iterface, so moving private data from the USB
interface to port is trivial.
Signed-off-by: Konstantin Shkolnyy <konstantin.shkolnyy@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Flush all device queues at close in order to work around a cp2108 Tx
queue bug.
Occasionally, writing data and immediately closing the port makes cp2108
stop responding. The device has to be unplugged to clear the error.
The failure is induced by shutting down the device while its Tx queue
still has unsent data. This condition is avoided by issuing PURGE command
from the close() callback.
This change is applied to all cp210x devices. Clearing internal queues on
close is generally good.
Signed-off-by: Konstantin Shkolnyy <konstantin.shkolnyy@gmail.com>
[johan: amend commit message ]
Signed-off-by: Johan Hovold <johan@kernel.org>
Sorry for the delay in this patch which was mostly caused by getting the
merger of the mpt2/mpt3sas driver, which was seen as an essential item of
maintenance work to do before the drivers diverge too much. Unfortunately,
this caused a compile failure (detected by linux-next), which then had to be
fixed up and incubated. In addition to the mpt2/3sas rework, there are
updates from pm80xx, lpfc, bnx2fc, hpsa, ipr, aacraid, megaraid_sas, storvsc
and ufs plus an assortment of changes including some year 2038 issues, a fix
for a remove before detach issue in some drivers and a couple of other minor
issues.
Signed-off-by: James Bottomley <JBottomley@Odin.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJWRnpiAAoJEDeqqVYsXL0MJd0IAIkNP1q/6ksMw/lam2UlbdxN
zFsFOIhGM3xLnBFehbCx7JW3cmybA7WC5jhMjaa1OeJmYHLpwbTzvVwrLs2l/0y1
/S+G0wwxROZfIKj/1EO3oKbSPCu9N3lStxOnmNXt5PSUEzAXrTqSNTtnMf2ZGh7j
bQxTWEJe+66GckgGw4ozTXJHWXqM/Zs/FsYjn2h/WzFhFv8utr7zRSzHMVjcqpLG
TK/Lt03hiTGqiignKrV9W6JzdGTWf2LGIsj/njgR0dxv59cNH8PrHIjZyknSBxgn
lblinsCjxDHWnP4BSfTi9MQG1lEiZiWO3Y6TKkKJTgxZ9M0Eitspc+cLOiJ1mpg=
=HvQf
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull final round of SCSI updates from James Bottomley:
"Sorry for the delay in this patch which was mostly caused by getting
the merger of the mpt2/mpt3sas driver, which was seen as an essential
item of maintenance work to do before the drivers diverge too much.
Unfortunately, this caused a compile failure (detected by linux-next),
which then had to be fixed up and incubated.
In addition to the mpt2/3sas rework, there are updates from pm80xx,
lpfc, bnx2fc, hpsa, ipr, aacraid, megaraid_sas, storvsc and ufs plus
an assortment of changes including some year 2038 issues, a fix for a
remove before detach issue in some drivers and a couple of other minor
issues"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (141 commits)
mpt3sas: fix inline markers on non inline function declarations
sd: Clear PS bit before Mode Select.
ibmvscsi: set max_lun to 32
ibmvscsi: display default value for max_id, max_lun and max_channel.
mptfusion: don't allow negative bytes in kbuf_alloc_2_sgl()
scsi: pmcraid: replace struct timeval with ktime_get_real_seconds()
mvumi: 64bit value for seconds_since1970
be2iscsi: Fix bogus WARN_ON length check
scsi_scan: don't dump trace when scsi_prep_async_scan() is called twice
mpt3sas: Bump mpt3sas driver version to 09.102.00.00
mpt3sas: Single driver module which supports both SAS 2.0 & SAS 3.0 HBAs
mpt2sas, mpt3sas: Update the driver versions
mpt3sas: setpci reset kernel oops fix
mpt3sas: Added OEM Gen2 PnP ID branding names
mpt3sas: Refcount fw_events and fix unsafe list usage
mpt3sas: Refcount sas_device objects and fix unsafe list usage
mpt3sas: sysfs attribute to report Backup Rail Monitor Status
mpt3sas: Ported WarpDrive product SSS6200 support
mpt3sas: fix for driver fails EEH, recovery from injected pci bus error
mpt3sas: Manage MSI-X vectors according to HBA device type
...
Pull SCSI target updates from Nicholas Bellinger:
"This series contains HCH's changes to absorb configfs attribute
->show() + ->store() function pointer usage from it's original
tree-wide consumers, into common configfs code.
It includes usb-gadget, target w/ drivers, netconsole and ocfs2
changes to realize the improved simplicity, that now renders the
original include/target/configfs_macros.h CPP magic for fabric drivers
and others, unnecessary and obsolete.
And with common code in place, new configfs attributes can be added
easier than ever before.
Note, there are further improvements in-flight from other folks for
v4.5 code in configfs land, plus number of target fixes for post -rc1
code"
In the meantime, a new user of the now-removed old configfs API came in
through the char/misc tree in commit 7bd1d4093c ("stm class: Introduce
an abstraction for System Trace Module devices").
This merge resolution comes from Alexander Shishkin, who updated his stm
class tracing abstraction to account for the removal of the old
show_attribute and store_attribute methods in commit 517982229f
("configfs: remove old API") from this pull. As Alexander says about
that patch:
"There's no need to keep an extra wrapper structure per item and the
awkward show_attribute/store_attribute item ops are no longer needed.
This patch converts policy code to the new api, all the while making
the code quite a bit smaller and easier on the eyes.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>"
That patch was folded into the merge so that the tree should be fully
bisectable.
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (23 commits)
configfs: remove old API
ocfs2/cluster: use per-attribute show and store methods
ocfs2/cluster: move locking into attribute store methods
netconsole: use per-attribute show and store methods
target: use per-attribute show and store methods
spear13xx_pcie_gadget: use per-attribute show and store methods
dlm: use per-attribute show and store methods
usb-gadget/f_serial: use per-attribute show and store methods
usb-gadget/f_phonet: use per-attribute show and store methods
usb-gadget/f_obex: use per-attribute show and store methods
usb-gadget/f_uac2: use per-attribute show and store methods
usb-gadget/f_uac1: use per-attribute show and store methods
usb-gadget/f_mass_storage: use per-attribute show and store methods
usb-gadget/f_sourcesink: use per-attribute show and store methods
usb-gadget/f_printer: use per-attribute show and store methods
usb-gadget/f_midi: use per-attribute show and store methods
usb-gadget/f_loopback: use per-attribute show and store methods
usb-gadget/ether: use per-attribute show and store methods
usb-gadget/f_acm: use per-attribute show and store methods
usb-gadget/f_hid: use per-attribute show and store methods
...
This patch changes the !blk-mq path to the same defaults as the blk-mq
I/O path by always enabling block tagging, and always using host wide
tags. We've had blk-mq available for a few releases so bugs with
this mode should have been ironed out, and this ensures we get better
coverage of over tagging setup over different configs.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Merge second patch-bomb from Andrew Morton:
- most of the rest of MM
- procfs
- lib/ updates
- printk updates
- bitops infrastructure tweaks
- checkpatch updates
- nilfs2 update
- signals
- various other misc bits: coredump, seqfile, kexec, pidns, zlib, ipc,
dma-debug, dma-mapping, ...
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (102 commits)
ipc,msg: drop dst nil validation in copy_msg
include/linux/zutil.h: fix usage example of zlib_adler32()
panic: release stale console lock to always get the logbuf printed out
dma-debug: check nents in dma_sync_sg*
dma-mapping: tidy up dma_parms default handling
pidns: fix set/getpriority and ioprio_set/get in PRIO_USER mode
kexec: use file name as the output message prefix
fs, seqfile: always allow oom killer
seq_file: reuse string_escape_str()
fs/seq_file: use seq_* helpers in seq_hex_dump()
coredump: change zap_threads() and zap_process() to use for_each_thread()
coredump: ensure all coredumping tasks have SIGNAL_GROUP_COREDUMP
signal: remove jffs2_garbage_collect_thread()->allow_signal(SIGCONT)
signal: introduce kernel_signal_stop() to fix jffs2_garbage_collect_thread()
signal: turn dequeue_signal_lock() into kernel_dequeue_signal()
signals: kill block_all_signals() and unblock_all_signals()
nilfs2: fix gcc uninitialized-variable warnings in powerpc build
nilfs2: fix gcc unused-but-set-variable warnings
MAINTAINERS: nilfs2: add header file for tracing
nilfs2: add tracepoints for analyzing reading and writing metadata files
...
1. Rename dequeue_signal_lock() to kernel_dequeue_signal(). This
matches another "for kthreads only" kernel_sigaction() helper.
2. Remove the "tsk" and "mask" arguments, they are always current
and current->blocked. And it is simply wrong if tsk != current.
3. We could also remove the 3rd "siginfo_t *info" arg but it looks
potentially useful. However we can simplify the callers if we
change kernel_dequeue_signal() to accept info => NULL.
4. Remove _irqsave, it is never called from atomic context.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Reviewed-by: Tejun Heo <tj@kernel.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
__GFP_WAIT has been used to identify atomic context in callers that hold
spinlocks or are in interrupts. They are expected to be high priority and
have access one of two watermarks lower than "min" which can be referred
to as the "atomic reserve". __GFP_HIGH users get access to the first
lower watermark and can be called the "high priority reserve".
Over time, callers had a requirement to not block when fallback options
were available. Some have abused __GFP_WAIT leading to a situation where
an optimisitic allocation with a fallback option can access atomic
reserves.
This patch uses __GFP_ATOMIC to identify callers that are truely atomic,
cannot sleep and have no alternative. High priority users continue to use
__GFP_HIGH. __GFP_DIRECT_RECLAIM identifies callers that can sleep and
are willing to enter direct reclaim. __GFP_KSWAPD_RECLAIM to identify
callers that want to wake kswapd for background reclaim. __GFP_WAIT is
redefined as a caller that is willing to enter direct reclaim and wake
kswapd for background reclaim.
This patch then converts a number of sites
o __GFP_ATOMIC is used by callers that are high priority and have memory
pools for those requests. GFP_ATOMIC uses this flag.
o Callers that have a limited mempool to guarantee forward progress clear
__GFP_DIRECT_RECLAIM but keep __GFP_KSWAPD_RECLAIM. bio allocations fall
into this category where kswapd will still be woken but atomic reserves
are not used as there is a one-entry mempool to guarantee progress.
o Callers that are checking if they are non-blocking should use the
helper gfpflags_allow_blocking() where possible. This is because
checking for __GFP_WAIT as was done historically now can trigger false
positives. Some exceptions like dm-crypt.c exist where the code intent
is clearer if __GFP_DIRECT_RECLAIM is used instead of the helper due to
flag manipulations.
o Callers that built their own GFP flags instead of starting with GFP_KERNEL
and friends now also need to specify __GFP_KSWAPD_RECLAIM.
The first key hazard to watch out for is callers that removed __GFP_WAIT
and was depending on access to atomic reserves for inconspicuous reasons.
In some cases it may be appropriate for them to use __GFP_HIGH.
The second key hazard is callers that assembled their own combination of
GFP flags instead of starting with something like GFP_KERNEL. They may
now wish to specify __GFP_KSWAPD_RECLAIM. It's almost certainly harmless
if it's missed in most cases as other activity will wake kswapd.
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Christoph Lameter <cl@linux.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Vitaly Wool <vitalywool@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The asm-generic changes for 4.4 are mostly a series from Christoph Hellwig
to clean up various abuses of headers in there. The patch to rename the
io-64-nonatomic-*.h headers caused some conflicts with new users, so I
added a workaround that we can remove in the next merge window.
The only other patch is a warning fix from Marek Vasut
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=dQKG
-----END PGP SIGNATURE-----
Merge tag 'asm-generic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic cleanups from Arnd Bergmann:
"The asm-generic changes for 4.4 are mostly a series from Christoph
Hellwig to clean up various abuses of headers in there. The patch to
rename the io-64-nonatomic-*.h headers caused some conflicts with new
users, so I added a workaround that we can remove in the next merge
window.
The only other patch is a warning fix from Marek Vasut"
* tag 'asm-generic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
asm-generic: temporarily add back asm-generic/io-64-nonatomic*.h
asm-generic: cmpxchg: avoid warnings from macro-ized cmpxchg() implementations
gpio-mxc: stop including <asm-generic/bug>
n_tracesink: stop including <asm-generic/bug>
n_tracerouter: stop including <asm-generic/bug>
mlx5: stop including <asm-generic/kmap_types.h>
hifn_795x: stop including <asm-generic/kmap_types.h>
drbd: stop including <asm-generic/kmap_types.h>
move count_zeroes.h out of asm-generic
move io-64-nonatomic*.h out of asm-generic
Quite a lot of activity in SPI this cycle, almost all of it in drivers
with a few minor improvements and tweaks in the core.
- Updates to pxa2xx to support Intel Broxton and multiple chip selects.
- Support for big endian in the bcm63xx driver.
- Multiple slave support for the mt8173
- New driver for the auxiliary SPI controller in bcm2835 SoCs.
- Support for Layerscale SoCs in the Freescale DSPI driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWOehzAAoJECTWi3JdVIfQTPYH+wYMDG8gAIw2s0AJ4DvVe4qZ
sOAm1UgUJZxssrEA6BNqbfM0dfRo+oQJKmRd0Dc5n7LEMsYHdI/5yKHk8PCS6ZzD
iQyQCzbd0thDAqwuPaMP62cyPDHwyJX22VGTsgVnj6AZqAQ+9+g4SPKhFnm1Mlm4
hmDi6fdSrsqo8k8gkpVN8RFOfVsjAV1dLtAauQRWDHrqMxXURSrKG76eqAqUa5bn
BLPXBoj5PA0DMLPO2j+ADZwWN723LrI2mSSlc+ThjEX/OIt2OhAoiOTV5RPqaafy
TIsCkh68q/gYAsL5HtvvmgZByl41FLYiO0Z+rXmWUyMMbnvhZTLws9S2BNpBLuk=
=DgXG
-----END PGP SIGNATURE-----
Merge tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"Quite a lot of activity in SPI this cycle, almost all of it in drivers
with a few minor improvements and tweaks in the core.
- Updates to pxa2xx to support Intel Broxton and multiple chip selects.
- Support for big endian in the bcm63xx driver.
- Multiple slave support for the mt8173
- New driver for the auxiliary SPI controller in bcm2835 SoCs.
- Support for Layerscale SoCs in the Freescale DSPI driver"
* tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (87 commits)
spi: pxa2xx: Rework self-initiated platform data creation for non-ACPI
spi: pxa2xx: Add support for Intel Broxton
spi: pxa2xx: Detect number of enabled Intel LPSS SPI chip select signals
spi: pxa2xx: Add output control for multiple Intel LPSS chip selects
spi: pxa2xx: Use LPSS prefix for defines that are Intel LPSS specific
spi: Add DSPI support for layerscape family
spi: ti-qspi: improve ->remove() callback
spi/spi-xilinx: Fix race condition on last word read
spi: Drop owner assignment from spi_drivers
spi: Add THIS_MODULE to spi_driver in SPI core
spi: Setup the master controller driver before setting the chipselect
spi: dw: replace magic constant by DW_SPI_DR
spi: mediatek: mt8173 spi multiple devices support
spi: mediatek: handle controller_data in mtk_spi_setup
spi: mediatek: remove mtk_spi_config
spi: mediatek: Update document devicetree bindings to support multiple devices
spi: fix kernel-doc warnings about missing return desc in spi.c
spi: fix kernel-doc warnings about missing return desc in spi.h
spi: pxa2xx: Align a few defines
spi: pxa2xx: Save other reg_cs_ctrl bits when configuring chip select
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=sR0p
-----END PGP SIGNATURE-----
Merge tag 'media/v4.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
"Media updates, including:
- Lots of improvements at the kABI documentation
- Split of Videobuf2 into a common part and a V4L2 specific one
- Split of the VB2 tracing events into a separate header file
- s5p-mfc got support for Exynos 5433
- v4l2 fixes for 64-bits alignment when running 32 bits userspace
on ARM
- Added support for SDR radio transmitter at core, vivid and hackrf
drivers
- Some y2038 fixups
- Some improvements at V4L2 colorspace support
- saa7164 converted to use the V4L2 core control framework
- several new boards additions, cleanups and fixups
PS: There are two patches for scripts/kernel-doc that are needed by
the documentation patches on Media. Jon is OK on merging those via
my tree"
* tag 'media/v4.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (146 commits)
[media] c8sectpfe: Remove select on CONFIG_FW_LOADER_USER_HELPER_FALLBACK
[media] DocBook media: update copyright/version numbers
[media] ivtv: Convert to get_user_pages_unlocked()
[media] media/v4l2-ctrls: fix setting autocluster to manual with VIDIOC_S_CTRL
[media] DocBook media: Fix a typo in encoder cmd
[media] DocBook: add SDR specific info to G_MODULATOR / S_MODULATOR
[media] DocBook: add SDR specific info to G_TUNER / S_TUNER
[media] hackrf: do not set human readable name for formats
[media] hackrf: add support for transmitter
[media] hackrf: switch to single function which configures everything
[media] hackrf: add control for RF amplifier
[media] DocBook: add modulator type field
[media] v4l: add type field to v4l2_modulator struct
[media] DocBook: document SDR transmitter
[media] v4l2: add support for SDR transmitter
[media] DocBook: document tuner RF gain control
[media] v4l2: add RF gain control
[media] v4l2: rename V4L2_TUNER_ADC to V4L2_TUNER_SDR
[media] media/vivid-osd: fix info leak in ioctl
[media] media: videobuf2: Move v4l2-specific stuff to videobuf2-v4l2
...
Here is the big tty and serial driver update for 4.4-rc1.
Lots of serial driver updates and a few small tty core changes. Full
details in the shortlog.
All of these have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlY6f64ACgkQMUfUDdst+ykf8gCfYPjtHy5hD/TsharaeXROnVgi
W8cAn16xk1Nmnde220MNNpO6zDu65G/1
=kslf
-----END PGP SIGNATURE-----
Merge tag 'tty-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here is the big tty and serial driver update for 4.4-rc1.
Lots of serial driver updates and a few small tty core changes. Full
details in the shortlog.
All of these have been in linux-next for a while"
* tag 'tty-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (148 commits)
tty: Use unbound workqueue for all input workers
tty: Abstract tty buffer work
tty: Prevent tty teardown during tty_write_message()
tty: core: Use correct spinlock flavor in tiocspgrp()
tty: Combine SIGTTOU/SIGTTIN handling
serial: amba-pl011: fix incorrect integer size in pl011_fifo_to_tty()
ttyFDC: Fix build problems due to use of module_{init,exit}
tty: remove unneeded return statement
serial: 8250_mid: add support for DMA engine handling from UART MMIO
dmaengine: hsu: remove platform data
dmaengine: hsu: introduce stubs for the exported functions
dmaengine: hsu: make the UART driver in control of selecting this driver
serial: fix mctrl helper functions
serial: 8250_pci: Intel MID UART support to its own driver
serial: fsl_lpuart: add earlycon support
tty: disable unbind for old 74xx based serial/mpsc console port
serial: pl011: Spelling s/clocks-names/clock-names/
n_tty: Remove reader wakeups for TTY_BREAK/TTY_PARITY chars
tty: synclink, fix indentation
serial: at91, fix rs485 properties
...
Here is the big USB patchset for 4.4-rc1.
As usual, most of the changes are in the gadget subsystem, and we
removed a host controller for a device that is no longer in existance,
and probably never was even made public. There is also other minor
driver updates and new device ids, full details in the changelog.
All of these have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlY6gVMACgkQMUfUDdst+ynLZgCePfhiDuwriaX7osq90HDu8JOc
pTEAn2dBdw2VMPToUlxccR963YSfgu2A
=mMgp
-----END PGP SIGNATURE-----
Merge tag 'usb-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here is the big USB patchset for 4.4-rc1.
As usual, most of the changes are in the gadget subsystem, and we
removed a host controller for a device that is no longer in existance,
and probably never was even made public. There is also other minor
driver updates and new device ids, full details in the changelog.
All of these have been in linux-next for a while"
* tag 'usb-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (233 commits)
USB: core: Codestyle fix in urb.c
usb: misc: usb3503: Use i2c_add_driver helper macro
usb: host: lpc32xx: don't unregister phy device
usb: host: lpc32xx: balance clk enable/disable on removal
usb: host: lpc32xx: fix warnings caused by enabling unprepared clock
uwb: drp: Use setup_timer
uwb: neh: Use setup_timer
uwb: rsv: Use setup_timer
USB: qcserial: add Sierra Wireless MC74xx/EM74xx
usb: chipidea: otg: don't wait vbus drops below BSV when starts host
chipidea: ci_hdrc_pci: use PCI_VDEVICE() instead of PCI_DEVICE()
doc: dt-binding: ci-hdrc-usb2: split vendor specific properties
usb: chipidea: imx: add imx6ul usb support
doc: dt-binding: ci-hdrc-usb2: improve property description
usb: chipidea: imx: add usb support for imx7d
Doc: usb: ci-hdrc-usb2: Add phy-clkgate-delay-us entry
usb: chipidea: Add support for 'phy-clkgate-delay-us' property
usb: chipidea: Use extcon framework for VBUS and ID detect
usb: gadget: net2280: restore ep_cfg after defect7374 workaround
usb: dwc2: host: Fix use after free w/ simultaneous irqs
...
v4.4 kernel development cycle:
Infrastructure:
- Doug Anderson wrote a patch adding an "init" state
different from the "default" state for pin control
state handling in the core framework. This is applied
before the driver's probe() call if defined and takes
precedence over "default". If both are defined, "init"
will be applied *before* probe() and "default" will be
applied *after* probe().
Significant subdriver improvements:
- SH PFC is switched to getting GPIO ranges from the
device tree ranges property on DT platforms.
- Got rid of CONFIG_ARCH_SHMOBILE_LEGACY, we are all
modernized.
- Got rid of SH PFC hardcoded IRQ numbers.
- Allwinner sunxi external interrupt through the "r"
controller.
- Moved the Cygnus driver to use DT-provided GPIO
ranges.
New drivers:
- Atmel PIO4 pin controller for the SAMA4D2 family
New subdrivers:
- Rockchip RK3036 subdriver
- Renesas SH PFC R8A7795 subdriver
- Allwinner sunxi A83T PIO subdriver
- Freescale i.MX7d iomux lpsr subdriver
- Marvell Berlin BG4CT subdriver
- SiRF Atlas 7 step B SoC subdriver
- Intel Broxton SoC subdriver
Apart from this, the usual slew if syntactic and semantic
fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=0t3B
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the big bulk of pin control changes for the v4.4 kernel
development cycle. Development pace is high in pin control again this
merge window. 28 contributors, 83 patches.
It hits a few sites outside the pin control subsystem:
- Device tree bindings in Documentation (as usual)
- MAINTAINERS
- drivers/base/* for the "init" state handling by Doug Anderson.
This has been ACKed by Greg.
- drivers/usb/renesas_usbhs/rcar2.c, for a dependent Renesas change
in the USB subsystem. This has been ACKed by both Greg and Felipe.
- arch/arm/boot/dts/sama5d2.dtsi - this should ideally have gone
through the ARM SoC tree but ended up here.
This time I am using Geert Uytterhoeven as submaintainer for SH PFC
since the are three-four people working in parallel with new Renesas
ASICs.
Summary of changes:
Infrastructure:
- Doug Anderson wrote a patch adding an "init" state different from
the "default" state for pin control state handling in the core
framework. This is applied before the driver's probe() call if
defined and takes precedence over "default". If both are defined,
"init" will be applied *before* probe() and "default" will be
applied *after* probe().
Significant subdriver improvements:
- SH PFC is switched to getting GPIO ranges from the device tree
ranges property on DT platforms.
- Got rid of CONFIG_ARCH_SHMOBILE_LEGACY, we are all modernized.
- Got rid of SH PFC hardcoded IRQ numbers.
- Allwinner sunxi external interrupt through the "r" controller.
- Moved the Cygnus driver to use DT-provided GPIO ranges.
New drivers:
- Atmel PIO4 pin controller for the SAMA4D2 family
New subdrivers:
- Rockchip RK3036 subdriver
- Renesas SH PFC R8A7795 subdriver
- Allwinner sunxi A83T PIO subdriver
- Freescale i.MX7d iomux lpsr subdriver
- Marvell Berlin BG4CT subdriver
- SiRF Atlas 7 step B SoC subdriver
- Intel Broxton SoC subdriver
Apart from this, the usual slew if syntactic and semantic fixes"
* tag 'pinctrl-v4.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (81 commits)
pinctrl: pinconf: remove needless loop
pinctrl: uniphier: guard uniphier directory with CONFIG_PINCTRL_UNIPHIER
pinctrl: zynq: fix UTF-8 errors
pinctrl: zynq: Initialize early
pinctrl: at91: add missing of_node_put
pinctrl: tegra-xusb: Correct lane mux options
pinctrl: intel: Add Intel Broxton pin controller support
pinctrl: intel: Allow requesting pins which are in ACPI mode as GPIOs
pinctrl: intel: Add support for multiple GPIO chips sharing the interrupt
drivers/pinctrl: Add the concept of an "init" state
pinctrl: uniphier: set input-enable before pin-muxing
pinctrl: cygnus: Add new compatible string for gpio controller driver
pinctrl: cygnus: Remove GPIO to Pinctrl pin mapping from driver
pinctrl: cygnus: Optional DT property to support pin mappings
pinctrl: sunxi: Add irq pinmuxing to sun6i "r" pincontroller
pinctrl: sunxi: Fix irq_of_xlate for the r_pio pinctrl block
pinctrl: sh-pfc: Remove obsolete r8a7778 platform_device_id entry
pinctrl: sh-pfc: Remove obsolete r8a7779 platform_device_id entry
pinctrl: sh-pfc: Stop including <linux/platform_data/gpio-rcar.h>
usb: renesas_usbhs: Remove unneeded #include <linux/platform_data/gpio-rcar.h>
...
This should be our final batch of fixes for 4.3:
- A patch from Sudeep Holla that fixes annotation of wakeup sources properly,
old unused format seems to have spread through copying.
- Two patches from Tony for OMAP. One dealing with MUSB setup problems due to
runtime PM being enabled too early on the parent device. The other fixes
IRQ numbering for OMAP1.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=jKgB
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"This should be our final batch of fixes for 4.3:
- A patch from Sudeep Holla that fixes annotation of wakeup sources
properly, old unused format seems to have spread through copying.
- Two patches from Tony for OMAP. One dealing with MUSB setup
problems due to runtime PM being enabled too early on the parent
device. The other fixes IRQ numbering for OMAP1"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
usb: musb: omap2430: Fix regression caused by driver core change
ARM: OMAP1: fix incorrect INT_DMA_LCD
ARM: dts: fix gpio-keys wakeup-source property
Commit ddef08dd00 ("Driver core: wakeup the parent device before trying
probe") started automatically ensuring the parent device is enabled when
the child gets probed.
This however caused a regression for MUSB omap2430 interface as the
runtime PM for the parent device needs the child initialized to access
the MUSB hardware registers.
Let's delay the enabling of PM runtime for the parent until the child
has been properly initialized as suggested in an earlier patch by
Grygorii Strashko <grygorii.strashko@ti.com>.
In addition to delaying pm_runtime_enable, we now also need to make sure
the parent is enabled during omap2430_musb_init. We also want to propagate
an error from omap2430_runtime_resume if struct musb is not initialized.
Note that we use pm_runtime_put_noidle here for both the child and parent
to prevent an extra runtime_suspend/resume cycle.
Let's also add some comments to avoid confusion between the
two different devices.
Fixes: ddef08dd00 ("Driver core: wakeup the parent device before
trying probe")
Suggested-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
An spi_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Delete braces around single statement block suggested by checkpatch.pl
Signed-off-by: Jonas Hesselmann <jonas.hesselmann@hotmail.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use i2c_add_driver as it will add THIS_MODULE for us.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to unregister the I2C device, which serves as a phy
from host code, this should be done in the correspondent phy driver.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The change adds missing clk_disable_unprepare(usb_otg_clk) call, also
the disabled clocks are sorted in order opposite to enabled clocks.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These updates generalise the option DTR/RTS handling so that all
usb-wwan-based drivers can use it. This is specifically needed by some
Sierra modems, which can now all be handled by qcserial again.
Included are also some clean ups of the io_ti firmware handling.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=B3KN
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for v4.4-rc1
These updates generalise the option DTR/RTS handling so that all
usb-wwan-based drivers can use it. This is specifically needed by some
Sierra modems, which can now all be handled by qcserial again.
Included are also some clean ups of the io_ti firmware handling.
Signed-off-by: Johan Hovold <johan@kernel.org>
- Use extcon framework for VBUS and ID detect
- Add imx6sx and imx7d support
- Other small changes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWKEKdAAoJEEhZKYFQ1nG7dysH/jmFSatDJvgA7woliRZ7p0H/
elNu6AOjqBnsi23Vp54IOVWYTVIDhLsXxlzEOgO6XXfsI99TqFQIIS2VYSo6xues
Eq5hIxh5n9uue3VMnw9bxYHcFkFG9LDAlyMXecEayAB74UqnQLbo2bRDfnSopaf1
dEOq9mdT8llYbtVww6bVXtL78wgwxVk1gTfISllxgt7DEuYwgT+gQJCDLrmkGPn0
XfiaZWamNmDlQd4z/qqoG65+yNmZZMZQKtugCx4MoiBbHVclRN7j2eNsCZ0y6dsZ
qxs+CazL/IeYCqxRRXl5Fopraer1uJeOPeFgA+lRV6WPhMEe7eg6ojkDp/8Y18Y=
=Dh+g
-----END PGP SIGNATURE-----
Merge tag 'usb-ci-v4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-next
Peter writes:
USB Chipidea updates for v4.4-rc1
- Use extcon framework for VBUS and ID detect
- Add imx6sx and imx7d support
- Other small changes
This pull request is large with a total of 136 non-merge
commits. Because of its size, we will only describe the big things in
broad terms.
Many will be happy to know that dwc3 is now almost twice as fast after
some profiling and speed improvements. Also in dwc3, John Youn from
Synopsys added support for their new DWC USB3.1 IP Core and the HAPS
platform which can be used to validate it.
A series of patches from Robert Baldyga cleaned up uses of
ep->driver_data as a flag for "claimed endpoint" in favor of the new
ep->claimed flag.
Sudip Mukherjee fixed a ton of really old problems on the amd5536udc
driver. That should make a few people happy.
Heikki Krogerus worked on converting dwc3 to the unified device property
interface.
Together with these, there's a ton of non-critical fixes, typos and
stuff like that.
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJWJoq5AAoJEIaOsuA1yqREOlkQAJTndRGxhcZR5rLzjyRDDags
pYoXJAqaneq5G8BwKY+2AQlPaUr87UEHUOo8pk4S31mdFHlp/d/6YIXLpdlYbEcW
ixGhtxZnUhyvWM0HYGgyoDGQP9YJXy5/MR2lEJhmsqcH/Q0dih5VrDGyJ3BxEboZ
2jXy7iou5fs5nHsR4fpdUH+ER//oKgHopRbbt+mmCwZbRJbuukA0KVDMHO8ix6cy
tG/8zbnv5RY3O4a0lJAST8LNmtpxfF9yUCs83b6muhLgO9GXUGYb+I8DjPJMbwag
klOy8Z1bG5e4ymh6383ZG7wDITf82N5cy5huoyunQHVjYg1L8vDHa9aF72e+yR/3
blb9OYALbKPV072HMwOfH+M9cvcCVDGytbJQIgMot9mjpP6GPhgbGtxb+RWNy2j8
Z2kEaxd3BUXvWiRbvyvn7uQuT/cAF4StrTnQrsbFSt0fKAUkQnGdK7XxYfGGql97
p3u2x2D7YSkurywMWyXjuBsm/mXsImAfTJvoWndyOIHU2PNAzIDM4k9TWaYNNAKA
ilZSuSC/JVnMPEH/J/QpytxMM5wbiGyJOyI4bc4MiAXgCkG3qm8vi0PMZM8x0rEu
q778B+50alg9U7/G75dt0WQP+kqDjn+iUB7i/YUC9sq/Dhlmpp48KvJU+zaco+7I
QsxGXmlgeA7yXX8ywy71
=jPoY
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v4.4 merge window
This pull request is large with a total of 136 non-merge
commits. Because of its size, we will only describe the big things in
broad terms.
Many will be happy to know that dwc3 is now almost twice as fast after
some profiling and speed improvements. Also in dwc3, John Youn from
Synopsys added support for their new DWC USB3.1 IP Core and the HAPS
platform which can be used to validate it.
A series of patches from Robert Baldyga cleaned up uses of
ep->driver_data as a flag for "claimed endpoint" in favor of the new
ep->claimed flag.
Sudip Mukherjee fixed a ton of really old problems on the amd5536udc
driver. That should make a few people happy.
Heikki Krogerus worked on converting dwc3 to the unified device property
interface.
Together with these, there's a ton of non-critical fixes, typos and
stuff like that.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Some HW design may use ID pin state to control vbus for otg port,
so before host role start, the vbus is already turned on, in this
case, we do not need wait vbus dropping below BSV.
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Fix using the PCI_DEVICE() macro instead of less verbose PCI_VDEVICE().
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Add imx6ul usb support.
Signed-off-by: Peter chen <peter.chen@freescale.com>
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Add support for the optional 'phy-clkgate-delay-us' property that is
used to describe the delay time between putting PHY into low power mode
and turning off the PHY clock.
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
On recent Qualcomm platforms VBUS and ID lines are not routed to
USB PHY LINK controller. Use extcon framework to receive connect
and disconnect ID and VBUS notification.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Replace struct v4l2_format * with void * to make queue_setup()
for common use.
And then, modify all device drivers related with this change.
Signed-off-by: Junghak Sung <jh1009.sung@samsung.com>
Signed-off-by: Geunyoung Kim <nenggun.kim@samsung.com>
Acked-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
[hans.verkuil@cisco.com: fix missing const in fimc-lite.c]
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Defect 7374 workaround enables all GPEP as endpoint 0. Restore
endpoint number when defect 7374 workaround is disabled. Otherwise,
check to match USB endpoint number to hardware endpoint number in
net2280_enable() fails.
Cc: <stable@vger.kernel.org> # 4.2
Reported-by: Paul Jones <p.jones@teclyn.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
While plugging / unplugging on a DWC2 host port with "slub_debug=FZPUA"
enabled, I found a crash that was quite obviously a use after free.
It appears that in some cases when we handle the various sub-cases of
HCINT we may end up freeing the QTD. If there is more than one bit set
in HCINT we may then end up continuing to use the QTD, which is bad.
Let's be paranoid and check for this after each sub-case. This should
be safe since we officially have the "hsotg->lock" (it was grabbed in
dwc2_handle_hcd_intr).
The specific crash I found was:
Unable to handle kernel paging request at virtual address 6b6b6b9f
At the time of the crash, the kernel reported:
(dwc2_hc_nak_intr+0x5c/0x198)
(dwc2_handle_hcd_intr+0xa84/0xbf8)
(_dwc2_hcd_irq+0x1c/0x20)
(usb_hcd_irq+0x34/0x48)
Popping into kgdb found that "*qtd" was filled with "0x6b", AKA qtd had
been freed and filled with slub_debug poison.
kgdb gave a little better stack crawl:
0 dwc2_hc_nak_intr (hsotg=hsotg@entry=0xec42e058,
chan=chan@entry=0xec546dc0, chnum=chnum@entry=4,
qtd=qtd@entry=0xec679600) at drivers/usb/dwc2/hcd_intr.c:1237
1 dwc2_hc_n_intr (chnum=4, hsotg=0xec42e058) at
drivers/usb/dwc2/hcd_intr.c:2041
2 dwc2_hc_intr (hsotg=0xec42e058) at drivers/usb/dwc2/hcd_intr.c:2078
3 dwc2_handle_hcd_intr (hsotg=0xec42e058) at
drivers/usb/dwc2/hcd_intr.c:2128
4 _dwc2_hcd_irq (hcd=<optimized out>) at drivers/usb/dwc2/hcd.c:2837
5 usb_hcd_irq (irq=<optimized out>, __hcd=<optimized out>) at
drivers/usb/core/hcd.c:2353
Popping up to frame #1 (dwc2_hc_n_intr) found:
(gdb) print /x hcint
$12 = 0x12
AKA:
#define HCINTMSK_CHHLTD (1 << 1)
#define HCINTMSK_NAK (1 << 4)
Further debugging found that by simulating receiving those two
interrupts at the same time it was trivial to replicate the
use-after-free. See <http://crosreview.com/305712> for a patch and
instructions. This lead to getting the following stack crawl of the
actual free:
0 arch_kgdb_breakpoint () at arch/arm/include/asm/outercache.h:103
1 kgdb_breakpoint () at kernel/debug/debug_core.c:1054
2 dwc2_hcd_qtd_unlink_and_free (hsotg=<optimized out>, qh=<optimized
out>, qtd=0xe4479a00) at drivers/usb/dwc2/hcd.h:488
3 dwc2_deactivate_qh (free_qtd=<optimized out>, qh=0xe5efa280,
hsotg=0xed424618) at drivers/usb/dwc2/hcd_intr.c:671
4 dwc2_release_channel (hsotg=hsotg@entry=0xed424618,
chan=chan@entry=0xed5be000, qtd=<optimized out>,
halt_status=<optimized out>) at drivers/usb/dwc2/hcd_intr.c:742
5 dwc2_halt_channel (hsotg=0xed424618, chan=0xed5be000, qtd=<optimized
out>, halt_status=<optimized out>) at
drivers/usb/dwc2/hcd_intr.c:804
6 dwc2_complete_non_periodic_xfer (chnum=<optimized out>,
halt_status=<optimized out>, qtd=<optimized out>, chan=<optimized
out>, hsotg=<optimized out>) at drivers/usb/dwc2/hcd_intr.c:889
7 dwc2_hc_xfercomp_intr (hsotg=hsotg@entry=0xed424618,
chan=chan@entry=0xed5be000, chnum=chnum@entry=6,
qtd=qtd@entry=0xe4479a00) at drivers/usb/dwc2/hcd_intr.c:1065
8 dwc2_hc_chhltd_intr_dma (qtd=0xe4479a00, chnum=6, chan=0xed5be000,
hsotg=0xed424618) at drivers/usb/dwc2/hcd_intr.c:1823
9 dwc2_hc_chhltd_intr (qtd=0xe4479a00, chnum=6, chan=0xed5be000,
hsotg=0xed424618) at drivers/usb/dwc2/hcd_intr.c:1944
10 dwc2_hc_n_intr (chnum=6, hsotg=0xed424618) at
drivers/usb/dwc2/hcd_intr.c:2052
11 dwc2_hc_intr (hsotg=0xed424618) at drivers/usb/dwc2/hcd_intr.c:2097
12 dwc2_handle_hcd_intr (hsotg=0xed424618) at
drivers/usb/dwc2/hcd_intr.c:2147
13 _dwc2_hcd_irq (hcd=<optimized out>) at drivers/usb/dwc2/hcd.c:2837
14 usb_hcd_irq (irq=<optimized out>, __hcd=<optimized out>) at
drivers/usb/core/hcd.c:2353
Though we could add specific code to handle this case, adding the
general purpose code to check for all cases where qtd might be freed
seemed safer.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
close_wait is no longer needed or provided by the tty core.
Move close_wait to struct gs_port.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch make changes to an if else statement which simplifies the code
allowing to remove a return.
CC: Joe Perches <joe@perches.com>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We received several reports of systems rebooting and powering on
after an attempted shutdown. Testing showed that setting
XHCI_SPURIOUS_WAKEUP quirk in addition to the XHCI_SPURIOUS_REBOOT
quirk allowed the system to shutdown as expected for LynxPoint-LP
xHCI controllers. Set the quirk back.
Note that the quirk was originally introduced for LynxPoint and
LynxPoint-LP just for this same reason. See:
commit 638298dc66 ("xhci: Fix spurious wakeups after S5 on Haswell")
It was later limited to only concern HP machines as it caused
regression on some machines, see both bug and commit:
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=66171
commit 6962d914f3 ("xhci: Limit the spurious wakeup fix only to HP machines")
Later it was discovered that the powering on after shutdown
was limited to LynxPoint-LP (Haswell-ULT) and that some non-LP HP
machine suffered from spontaneous resume from S3 (which should
not be related to the SPURIOUS_WAKEUP quirk at all). An attempt
to fix this then removed the SPURIOUS_WAKEUP flag usage completely.
commit b45abacde3 ("xhci: no switching back on non-ULT Haswell")
Current understanding is that LynxPoint-LP (Haswell ULT) machines
need the SPURIOUS_WAKEUP quirk, otherwise they will restart, and
plain Lynxpoint (Haswell) machines may _not_ have the quirk
set otherwise they again will restart.
Signed-off-by: Laura Abbott <labbott@fedoraproject.org>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Oliver Neukum <oneukum@suse.com>
[Added more history to commit message -Mathias]
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a host fails to wake up a isochronous SuperSpeed device from U1/U2
in time for a isoch transfer it will generate a "No ping response error"
Host will then move to the next transfer descriptor.
Handle this case in the same way as missed service errors, tag the
current TD as skipped and handle it on the next transfer event.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the difference is big enough between the bytes asked and received
in a bulk transfer we can get a short transfer event pointing to a TRB in
the middle of the TD. We don't want to handle the TD yet as we will anyway
receive a new event for the last TRB in the TD.
Hold off from finishing the TD and removing it from the list until we
receive an event for the last TRB in the TD
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
checkpatch complains about too many leading tabs because the if
statement starts after 6 tabs:
scan_iosoc() -> for() -> while() -> switch() -> if() -> for() -> if()
There is also a goto statement going backwards in case of failure. This
patch creates a new inline function named scan_frame_queue() containing
the last 4 nesting levels, and removes the need of backwards goto,
making the code easier to read. After the patch it becomes:
scan_iosoc() -> for() -> while() -> scan_frame_queue()
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
checkpatch complains about too many leading tabs because the switch
statement starts after 6 tabs.
fill_periodic_buffer() -> for() -> do -> switch() -> if() ->
list_for_each_entry() and finally the last switch().
This patch moves the list_for_each_entry() and the last switch() to a
new function named output_buf_tds_dir(). This change makes the code
easier to read and calm down checkpatch. This patch changes it to:
fill_periodic_buffer() -> for() -> do -> switch() -> if() ->
output_buf_tds_dir()
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch convert the macro speed_char in an inline function. The goal
of this patch is to make the code easier to read.
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
msleep under 20ms can result in sleeping up to 20ms, which may not be
intended. Replace msleep(5) by usleep_range(5000, 10000). The range of 5
ms is to reduce the chances of creating an interrupt while reducing the
maximum wait time in 50%.
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch replaces:
kmalloc(DBG_SCHED_LIMIT * sizeof(*seen), GFP_ATOMIC)
by:
kmalloc_array(DBG_SCHED_LIMIT, sizeof(*seen), GFP_ATOMIC)
as kmalloc_array() should be used for allocating arrays.
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
