The most important fixes here are:
a) yet another fix to dwc3's EP transfer resource
assignment logic. This time around we will be
pre-allocating transfer resources to avoid any
future issues;
b) two DMA fixes for the old MUSB driver.
c) dwc2's data toggle fix for FS
Other than these, we have a few other minor fixes
elsewhere.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=5QjC
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v4.5-rc6' of http://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v4.5-rc6
The most important fixes here are:
a) yet another fix to dwc3's EP transfer resource
assignment logic. This time around we will be
pre-allocating transfer resources to avoid any
future issues;
b) two DMA fixes for the old MUSB driver.
c) dwc2's data toggle fix for FS
Other than these, we have a few other minor fixes
elsewhere.
Commit ac33cdb166 ("usb: musb: Remove ifdefs for musb_host_rx in
musb_host.c part5") introduces a problem setting DMA host mode.
The musb_advance_schedule() is called immediately after receiving an
endpoint RX interrupt without waiting for the DMA transfer to complete.
As a consequence when the dma complete interrupt arrives the in_qh
member of hw_ep is already null an the musb_host_rx() exits on !urb
error case. Fix the done condition that advances the musb schedule.
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Joshua Henderson <joshua.henderson@microchip.com>
Tested-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
When working in Dual Role Device mode, USB state machine is not kicked,
when host or gadget drivers are loaded. Fix this be explicitly triggering
state detection on client driver load.
Issue is that if the board is booted without micro usb cable and usb
device attached, kernel fails to populate the usb host and device.
The reason for this is that the state machine worker logic only checks
for USB_DR_MODE_PERIPHERAL and USB_DR_MODE_HOST modes to run worker
thread. However if the phy is configured in OTG mode it would fail
to run the state machine, resulting in failure to detect for very
first time.
This patch fixes the issue by removing the explicit checks.
Issue is noticed on Qualcomm Dragon board DB410C.
[srinivas.kandagatla@linaro.org: Added more details to log]
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This patch fixes the register offset used for super-speed connection's
max packet size. Without it using the 338x series of devices in enhanced
mode will only allow full or high speed operation to function correctly.
Signed-off-by: Simon Appleby <simon.appleby@pickeringtest.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Gadgetfs driver called usb_gadget_unregister_driver unconditionally, even
if it didn't register it earlier due to other failures. This patch fixes
this.
Reported-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Retry gadget probe only if the probe result is -EPROBE_DEFER, not on
every probe error.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This reverts commit d8f00cd685.
Tony writes:
This upstream commit is causing an oops:
d8f00cd685 ("usb: hub: do not clear BOS field during reset device")
This patch has already been included in several -stable kernels. Here
are the affected kernels:
4.5.0-rc4 (current git)
4.4.2
4.3.6 (currently in review)
4.1.18
3.18.27
3.14.61
How to reproduce the problem:
Boot kernel with slub debugging enabled (otherwise memory corruption
will cause random oopses later instead of immediately)
Plug in USB 3.0 disk to xhci USB 3.0 port
dd if=/dev/sdc of=/dev/null bs=65536
(where /dev/sdc is the USB 3.0 disk)
Unplug USB cable while dd is still going
Oops is immediate:
Reported-by: Tony Battersby <tonyb@cybernetics.com>
Cc: Du, Changbin <changbin.du@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some new device ids.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABCAAGBQJWx3i4AAoJEEEN5E/e4bSVUncP/Rm5vy+8YJ8u2NzvXOtzXdoe
2+Ef8yE402DQl9d4SJNg5mL8nNcdUDaZGRoLKDlnws/iX1PcQf6RxrR4fhYbR8xk
kd6+BT+rUzICI7xD5Q190GPV4InFUXDJ9lH89LPb75A9aMLdffy+WpEFoXoKlDaw
O01b/OZClAsxqNmMO0UKr8Xbki2hMPlP5AM6rOVn5eJqZv4FB9mD/C9pwxxloW75
8iBq5pRHrJpHw3AiWOz9npW5RUxOag0HRln4Lx9b7gOHeMY/JH440LVufjQB0/4Y
cJ/G3w94rJqAuJ+87fYXJ8zDmAHTOfCVqSuloC7o4GqNXjV1PayRj3MMxOLjusHg
DLuCkZquCEQ8+X2+j09A/0+k4XFw6he+a8n7dmzJzfMYH5DAd+WU1oMn9c8p/zG6
Vf9t0C9m4DtCMh+lO1cz5M3q8133cePf282ogCkK8meGISBZH2ZUMSJWqkn9+RYd
/rytj1UVq5UH8wVqNPu2fVlIqEk3AaG8VrM7iLHGsEE4BsYJ3fYyEvu1NeVXqMEa
thZZQBrvBCkObZsJzkZIfKhjisvN+Pg1Wo4X3OzsFuXxt56zZYh52ysFl43GEyWp
Jyw+8ggpiWd5nrvps3uVMvDVLwaIhhCgMUW2XgVnnrtxBtFfguJRAjWjO513esuy
C0EfegNX9Qzx2MSTrtSH
=eFQw
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.5-rc5
Here are some new device ids.
Signed-off-by: Johan Hovold <johan@kernel.org>
In case of error, the function usb_phy_generic_register()
returns ERR_PTR() and never returns NULL. The NULL test in
the return value check should be replaced with IS_ERR().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
The write value is 8bit, but currently writing a larger number
(eg a doubled digit) is not errored but instead gets cast and
sets off an action probably undesired.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
(Change the style of commit log to fix checkpatch.pl warning)
Add USB ID for cp2104/5 devices on GE B650v3 and B850v3 boards.
Signed-off-by: Ken Lin <ken.lin@advantech.com.tw>
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Commit 754fe4a92c ("usb: musb: Remove ifdefs for TX DMA for musb_host.c")
introduces a problem setting the desired channel mode for the Mentor DMA
engine.
There is a case where an address is incorrectly assigned to the DMA
channel desired mode when it should instead be assigned the actual mode
value. This results in the value of channel->desired_mode not being
correct.
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Joshua Henderson <joshua.henderson@microchip.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
There will be data toggle error happen for full speed buld-out transfer.
The data toggle bit is saved in qh for non-control transfers, it is wrong
to check the qtd for that case.
Also fix one static analysis tool issue after fix the data toggle error.
John Youn:
* Added WARN() to warn on improper usage of the
dwc2_hcd_save_data_toggle() function.
Signed-off-by: Dyson Lee <dyson.lee@intel.com>
Signed-off-by: Tang, Jianqiang <jianqiang.tang@intel.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Fixes memory manipulation issues and makes Host DDMA bulk transfers
work.
dwc2_process_non_isoc_desc() must return non zero value ONLY when
failure happens in one of the queued descriptors. After receiving
non zero value the caller must stop processing of remaining
QTDs and their descriptors from chain.
Commit 26a19ea699 ("usb: dwc2: host: fix use of qtd after
free in desc dma mode") breaks non_isoc transaction completion logic
in Host DDMA mode. There were bugs before that, but after this patch
dwc2_process_non_isoc_desc() returns fail status even if descriptor
was processed normally. This causes break from loop which is processing
remaining descriptors assigned to QTD, which is not correct for QTDs
containing more than one descriptor.
Current dwc2 driver gathers queued BULK URBs until receiving URB
without URB_NO_INTERRUPT flag. Once getting it, SW creates
descriptor chain, stores it in qh structure and passes start
address to HW. Multiple URB data is contained in that chain.
Hence on getting error on descriptor after its processing by HW,
SW should go out of both loops(qh->qtd, qtd->descs) and report
the failure.
Fixes: 26a19ea699 ("usb: dwc2: host: fix use of qtd after free in desc dma mode")
Cc: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The assignement of EP transfer resources was not handled properly in the
dwc3 driver. Commit aebda61871 ("usb: dwc3: Reset the transfer
resource index on SET_INTERFACE") previously fixed one aspect of this
where resources may be exhausted with multiple calls to SET_INTERFACE.
However, it introduced an issue where composite devices with multiple
interfaces can be assigned the same transfer resources for different
endpoints. This patch solves both issues.
The assignment of transfer resources cannot perfectly follow the data
book due to the fact that the controller driver does not have all
knowledge of the configuration in advance. It is given this information
piecemeal by the composite gadget framework after every
SET_CONFIGURATION and SET_INTERFACE. Trying to follow the databook
programming model in this scenario can cause errors. For two reasons:
1) The databook says to do DEPSTARTCFG for every SET_CONFIGURATION and
SET_INTERFACE (8.1.5). This is incorrect in the scenario of multiple
interfaces.
2) The databook does not mention doing more DEPXFERCFG for new endpoint
on alt setting (8.1.6).
The following simplified method is used instead:
All hardware endpoints can be assigned a transfer resource and this
setting will stay persistent until either a core reset or hibernation.
So whenever we do a DEPSTARTCFG(0) we can go ahead and do DEPXFERCFG for
every hardware endpoint as well. We are guaranteed that there are as
many transfer resources as endpoints.
This patch triggers off of the calling dwc3_gadget_start_config() for
EP0-out, which always happens first, and which should only happen in one
of the above conditions.
Fixes: aebda61871 ("usb: dwc3: Reset the transfer resource index on SET_INTERFACE")
Cc: <stable@vger.kernel.org> # v3.2+
Reported-by: Ravi Babu <ravibabu@ti.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Fixes an issue found on rockchip rk3036 and rk3188 SOC platforms. For
some reason, the existing msleep(25) is not enough after the force mode.
The following patch was reported to fix the issue.
This does increase the probe delay again slightly, but not up to the
level it was before the original series of patches that this fixes. It
does not cause any other issues when tested on Synopsys HAPS and Altera
socfpga platforms.
Need to revisit this series next release to see if we can address these
issues without having an unconditional delay.
Fixes: 09c96980dc ("usb: dwc2: Add functions to set and clear force mode")
Reported-by: Caesar Wang <caesar.upstream@gmail.com>
Reported-by: Michael Niewoehner <linux@mniewoehner.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Caesar Wang <caesar.upstream@gmail.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
xhci_find_next_ext_cap doesn't check for PCI hotplug removal and may use
the PCI master abort bit pattern (~0) to calculate a new PCI address
offset to read/write. The has lead to reproducable crashes when testing
surprise removal during device initialization on a Stratus platform, at
least after commit d5ddcdf4d6 ("xhci: rework xhci extended capability
list parsing functions").
The crash is repeatable on a Stratus platform when injecting hardware
faults to induce xHCI host controller hotplug during driver
initialization. If a PCI read in xhci_find_next_ext_cap returns the
master abort pattern, quirk_usb_handoff_xhci may start using a bogus
ext_cap_offset to start searching more bogus PCI addresses.
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DWC3 got a fix for OTG Certification, DWC2 has two fixes for regressions on
RasPI, MUSB has a NULL pointer dereference fix for ux500 platforms and two
PHYs (MSM and MXS) got some minor fixes.
While at that, I'm also adding a fix to my email address which has changed
recently.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Zhyq
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v4.5-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v4.5-rc2
DWC3 got a fix for OTG Certification, DWC2 has two fixes for regressions on
RasPI, MUSB has a NULL pointer dereference fix for ux500 platforms and two
PHYs (MSM and MXS) got some minor fixes.
While at that, I'm also adding a fix to my email address which has changed
recently.
xhci driver frees data for all devices, both usb2 and and usb3 the
first time usb_remove_hcd() is called, including td_list and and xhci_ring
structures.
When usb_remove_hcd() is called a second time for the second xhci bus it
will try to dequeue all pending urbs, and touches td_list which is already
freed for that endpoint.
Cc: <stable@vger.kernel.org>
Reported-by: Joe Lawrence <joe.lawrence@stratus.com>
Tested-by: Joe Lawrence <joe.lawrence@stratus.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During probe, in the device tree case, the data pointer associated to a
compatible is dereferenced. However, not all the compatibles are
associated to a private data pointer.
The generic-xhci and the xhci-platform don't need them, this patch adds a
test on the data pointer before accessing it, avoiding a kernel crash.
Fixes: 4efb2f6941 ("usb: host: xhci-plat: add struct xhci_plat_priv")
Cc: stable@vger.kernel.org
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
when ip fails to enter sleep mode, register access protection will
be disabled, at the same time if all clocks are disabled, access
register will hang up AHB bus.
the common case causes ip sleep failure is that after all ports
enter U3 but before ip enters sleep mode, a port receives a resume
signal('K'). this will happens when such as clicks mouse to try to
do remote-wakeup to stop system enter suspend.
so stop polling root hubs to avoid access xHCI register on bus
suspend, and restart it when bus resumes.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
when a LS or FS device doesn't connect though a HS hub,
the @bPkts field of its periodic endpoint context should
be set to 1.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel Broxton M was verifed to require XHCI_PME_STUCK_QUIRK quirk as well.
Cc: stable@vger.kernel.org
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
XHCI_SSIC_PORT_UNUSED quirk was applied to the xHCI host controllers
in some Intel SoC chips. With this quirk applied, SSIC port is set
to "unused" prior to xhci_suspend(). This may cause problem if host
fails to suspend. In this case, the port is set to unused without
host further entering D3, and the port will not be usable anymore.
Cc: stable@vger.kernel.org
Signed-off-by: Zhuang Jin Can <jin.can.zhuang@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Two workarounds introduced by commit b8cb91e058 ("xhci: Workaround
for PME stuck issues in Intel xhci") and commit abce329c27 ("xhci:
Workaround to get D3 working in Intel xHCI") share a single quirk bit
XHCI_PME_STUCK_QUIRK. These two workarounds actually are different and
might happen on different hardwares. Need to separate them by adding a
quirk bit for the later.
Cc: stable@vger.kernel.org
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit abce329c27 ("xhci: Workaround to get D3 working in Intel xHCI")
adds a workaround for a limitation of PME storm caused by SSIC port in
some Intel SoCs. This commit only handled one SSIC port, while there
are actually two SSIC ports in the chips. This patch handles both SSIC
ports. Without this fix, users still see PME storm.
Cc: stable@vger.kernel.org # v4.2+
Signed-off-by: Zhuang Jin Can <jin.can.zhuang@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch is needed in order to pass one test case
defined in the OTG Automated Compliance Test specification.
Specification location:
http://www.usb.org/developers/onthego/otgeh_compliance_plan_1_2.pdf
This test case uses PET Tool, and PET Tool is one USB hardware
equipment provided by MQP Electronics.
Test case id is 6.8.3 B-UUT Bypass Capacitance.
We must set this otg flag in order to be able to return OTG
descriptor during enumeration, otherwise this test case with
failed with below error: "Get OTG descriptor request stalled".
Signed-off-by: Jianqiang Tang <jianqiang.tang@intel.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This reverts commit e210c422b6 ("xhci: don't finish a TD if we get a
short transfer event mid TD")
Turns out that most host controllers do not follow the xHCI specs and never
send the second event for the last TRB in the TD if there was a short event
mid-TD.
Returning the URB directly after the first short-transfer event is far
better than never returning the URB. (class drivers usually timeout
after 30sec). For the hosts that do send the second event we will go
back to treating it as misplaced event and print an error message for it.
The origial patch was sent to stable kernels and needs to be reverted from
there as well
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes an issue found on Raspberry PI platform that prevents probe. Don't
skip setting the force mode if it's already set.
Fixes: 09c96980dc ("usb: dwc2: Add functions to set and clear force mode")
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Reported-by: Stefan Wahren <stefan.wahren@i2se.com>
Reported-by: Remi Pommarel <repk@triplefau.lt>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Tested-by: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This reverts commit 263b7fb557 ("usb: dwc2: Move reset into
dwc2_get_hwparams()") due to regression found on bcm2835 platform. USB
ethernet fails, due to being unable to pick up proper parameters when
performing a plain reset before reading hw params.
Below shows the results of the gnptxfsiz and hptxfsiz with and before
and after reverting this (from Stefan Wahren):
So here is the probe result before Patch 1 is applied:
[ 1.283148] dwc2 20980000.usb: Configuration mismatch. dr_mode forced to host
[ 1.313894] dwc2 20980000.usb: gnptxfsiz=00201000
[ 1.314104] dwc2 20980000.usb: hptxfsiz=00000000
[ 1.353908] dwc2 20980000.usb: 256 invalid for host_nperio_tx_fifo_size. Check HW configuration.
[ 1.354262] dwc2 20980000.usb: 512 invalid for host_perio_tx_fifo_size. Check HW configuration.
[ 1.394249] dwc2 20980000.usb: DWC OTG Controller
[ 1.394561] dwc2 20980000.usb: new USB bus registered, assigned bus number 1
[ 1.394917] dwc2 20980000.usb: irq 33, io mem 0x00000000
And here is the probe result after Patch 1 is applied:
[ 1.280107] dwc2 20980000.usb: Configuration mismatch. dr_mode forced to host
[ 1.353949] dwc2 20980000.usb: gnptxfsiz=01001000
[ 1.354166] dwc2 20980000.usb: hptxfsiz=02002000
[ 1.434301] dwc2 20980000.usb: DWC OTG Controller
[ 1.434616] dwc2 20980000.usb: new USB bus registered, assigned bus number 1
[ 1.434973] dwc2 20980000.usb: irq 33, io mem 0x00000000
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Reported-by: Stefan Wahren <stefan.wahren@i2se.com>
Reported-by: Remi Pommarel <repk@triplefau.lt>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Tested-by: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The commit 7d32cdef53 ("usb: musb: fail with error when no DMA
controller set"), caused the core platform driver to correctly return an
error code when fail probing.
Unfurtante it also caused bug for a NULL pointer dereference, during
system suspend for the ux500 driver. The reason is a lacking validation
of the corresponding ->driver_data pointer, which won't be set when the
musb core driver fails to probe (or haven't yet been probed).
Fixes: 7d32cdef53 ("usb: musb: fail with error when no DMA...")
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Initialize vbus_value to be 0 since it's possible not to assign
any value before judgement.
Acked-by: Peter Chen <peter.chen@nxp.com
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This driver registers for extcon events as part of its probe, but
never unregisters them in case of error in the probe path.
There were multiple issues noticed due to this missing error handling.
One of them is random crashes if the regulators are not ready yet by the
time probe is invoked.
Ivan's previous attempt [1] to fix this issue, did not really address
all the failure cases like regualtor/get_irq failures.
[1] https://lkml.org/lkml/2015/9/7/62
Without this patch the kernel would carsh with log:
...
Unable to handle kernel paging request at virtual address 17d78410
pgd = ffffffc001a5c000
[17d78410] *pgd=00000000b6806003, *pud=00000000b6806003, *pmd=0000000000000000
Internal error: Oops: 96000005 [#1] PREEMPT SMP
Modules linked in:
CPU: 0 PID: 6 Comm: kworker/u8:0 Not tainted 4.4.0+ #48
Hardware name: Qualcomm Technologies, Inc. APQ 8016 SBC (DT)
Workqueue: deferwq deferred_probe_work_func
task: ffffffc03686e900 ti: ffffffc0368b0000 task.ti: ffffffc0368b0000
PC is at raw_notifier_chain_register+0x1c/0x44
LR is at extcon_register_notifier+0x88/0xc8
pc : [<ffffffc0000da43c>] lr : [<ffffffc000606298>] pstate: 80000085
sp : ffffffc0368b3a70
x29: ffffffc0368b3a70 x28: ffffffc03680c310
x27: ffffffc035518000 x26: ffffffc035518000
x25: ffffffc03bfa20e0 x24: ffffffc035580a18
x23: 0000000000000000 x22: ffffffc035518458
x21: ffffffc0355e9a60 x20: ffffffc035518000
x19: 0000000000000000 x18: 0000000000000028
x17: 0000000000000003 x16: ffffffc0018153c8
x15: 0000000000000001 x14: ffffffc03686f0f8
x13: ffffffc03686f0f8 x12: 0000000000000003
x11: 0000000000000001 x10: 0000000000000001
x9 : ffffffc03686f0f8 x8 : 0000e3872014c1a1
x7 : 0000000000000028 x6 : 0000000000000000
x5 : 0000000000000001 x4 : 0000000000000000
x3 : 00000000354fb170 x2 : 0000000017d78400
x1 : ffffffc0355e9a60 x0 : ffffffc0354fb268
Fixes: 591fc116f3 ("usb: phy: msm: Use extcon framework for VBUS and ID detection")
CC: Stable <stable@vger.kernel.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Here are two fixes of crashes in the visor driver that could be
triggered using bad (malicious) descriptors, a fix for two memory leaks
in the new mxu11x0 driver, and an interface-blacklist fix for the option
driver.
Included are also some new device ids.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABCAAGBQJWqi2hAAoJEEEN5E/e4bSV5VQQALpo+SexxQJo4tzl33jaSU03
QMWAqld5UHwmKxzMXOCMg+XBFSfkU3W+EtxrSJl/HCOSWeCveDTvPFEmjgXkfZGq
aJvW8bmg/a7lTwk+Fv9For1zlAv0OEpAFv1i9L+U3LI39lUn9eG2OgsOisnnvlww
ay0lQ21CH5ta7RVbsTnxpLVWsuvEuhR75pIXKwpvGoGui5KU2HnNDTsjit5Ih9kn
dYJZJVozry6xknQ651wHR5jm/40fFJ8J/xmDlJlMxu3Y6CyN8BCGKlM0yc/Qujgz
/7Gm52b3qt5EhEvbt+vopg4iy3JhG9S/GNtMGxoUETlqaGz1v2cwUsMTI48yHKP2
ihVVKeRaVrYyoipg9/pKno8bnWouiFdSRm/rmKVl1XltM5Z7il7QTrRscrJflV2L
MFKVILrRn78o8tLqkbJbpB1HpPpCXGdsjgv9kMNwb0A/qdiYCWCXWTxPNC1XOA9X
t2yOLsD4tGkc3llNvIuDCX9U5gyokff7hY1z01IVbIkCKLxrI3paxGVx1M59QqfE
G2QeyC6rJXvev/3EOAQf/r38TqIzaohkTikAJRaMXoGDlWQEGH3JkmnTnY/lSxZS
LZCgz7m2JIe/6lUIlM3a0f2SudyCkd0rMnSfO6jzbt/iP56ggPnHS4uAzjaSdMqJ
/uQs6Kbamq1d8cqiARwJ
=SxKT
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.5-rc2
Here are two fixes of crashes in the visor driver that could be
triggered using bad (malicious) descriptors, a fix for two memory leaks
in the new mxu11x0 driver, and an interface-blacklist fix for the option
driver.
Included are also some new device ids.
Signed-off-by: Johan Hovold <johan@kernel.org>
On nominal execution, private data allocated on port_probe and attach
are never freed. Add port_remove and release callbacks to free them
respectively.
Signed-off-by: Mathieu OTHACEHE <m.othacehe@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Harald Linden reports that the ftdi_sio driver works properly for the
Yaesu SCU-18 cable if the device ids are added to the driver. So let's
add them.
Reported-by: Harald Linden <harald.linden@7183.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
This patch adds support for two PIDs of LE922.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The visor driver crashes in clie_5_attach() when a specially crafted USB
device without bulk-out endpoint is detected. This fix adds a check that
the device has proper configuration expected by the driver.
Reported-by: Ralf Spenneberg <ralf@spenneberg.net>
Signed-off-by: Vladis Dronov <vdronov@redhat.com>
Fixes: cfb8da8f69 ("USB: visor: fix initialisation of UX50/TH55 devices")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix null-pointer dereference at probe should a (malicious) Treo device
lack the expected endpoints.
Specifically, the Treo port-setup hack was dereferencing the bulk-in and
interrupt-in urbs without first making sure they had been allocated by
core.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Added the USB serial console device ID for IAI Corp. RCB-CV-USB
USB to RS485 adaptor.
Signed-off-by: Peter Dedecker <peter.dedecker@hotmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
In function usb_reset_and_verify_device, the old BOS descriptor may
still be used before allocating a new one. (usb_unlocked_disable_lpm
function uses it under the situation that it fails to disable lpm.)
So we cannot set the udev->bos to NULL before that, just keep what it
was. It will be overwrite when allocating a new one.
Crash log:
BUG: unable to handle kernel NULL pointer dereference at
0000000000000010
IP: [<ffffffff8171f98d>] usb_enable_link_state+0x2d/0x2f0
Call Trace:
[<ffffffff8171ed5b>] ? usb_set_lpm_timeout+0x12b/0x140
[<ffffffff8171fcd1>] usb_enable_lpm+0x81/0xa0
[<ffffffff8171fdd8>] usb_disable_lpm+0xa8/0xc0
[<ffffffff8171fe1c>] usb_unlocked_disable_lpm+0x2c/0x50
[<ffffffff81723933>] usb_reset_and_verify_device+0xc3/0x710
[<ffffffff8172c4ed>] ? usb_sg_wait+0x13d/0x190
[<ffffffff81724743>] usb_reset_device+0x133/0x280
[<ffffffff8179ccd1>] usb_stor_port_reset+0x61/0x70
[<ffffffff8179cd68>] usb_stor_invoke_transport+0x88/0x520
Signed-off-by: Du, Changbin <changbin.du@intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This phone needs to be handled by a specialised firmware tool
and is reported to crash irrevocably if cdc-acm takes it.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
CC: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For Intel 7260 modem, it is needed for host side to send zero
packet if the BULK OUT size is equal to USB endpoint max packet
length. Otherwise, modem side may still wait for more data and
cannot give response to host side.
Signed-off-by: Konrad Leszczynski <konrad.leszczynski@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In current acm driver, the bulk-in callback function ignores the
URBs unlinked in usb core.
This causes unexpected data loss in some cases. For example,
runtime suspend entry will unlinked all urbs and set urb->status
to -ENOENT even those urbs might have data not processed yet.
Hence, data loss occurs.
This patch lets bulk-in callback function handle unlinked urbs
to avoid data loss.
Signed-off-by: Tang Jian Qiang <jianqiang.tang@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Cc: stable@vger.kernel.org
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull final vfs updates from Al Viro:
- The ->i_mutex wrappers (with small prereq in lustre)
- a fix for too early freeing of symlink bodies on shmem (they need to
be RCU-delayed) (-stable fodder)
- followup to dedupe stuff merged this cycle
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
vfs: abort dedupe loop if fatal signals are pending
make sure that freeing shmem fast symlinks is RCU-delayed
wrappers for ->i_mutex access
lustre: remove unused declaration
