Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
As we reset the GPMI block at resume, the timing parameters setup by a
previous exec_op is lost. Rewriting GPMI timing registers on first exec_op
after resume fixes the problem.
Fixes: ef347c0cfd ("mtd: rawnand: gpmi: Implement exec_op")
Cc: stable@vger.kernel.org
Signed-off-by: Esben Haabendal <esben@geanix.com>
Acked-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The commit converting the driver to DMAengine was missing the flags for
the memcpy prepare call.
It went unnoticed since the omap-dma driver was ignoring them.
Fixes: 3ed6a4d1de (" mtd: onenand: omap2: Convert to use dmaengine for memcp")
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: H. Nikolaus Schaller <hns@goldelico.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Use dma_addr_t type to pass memory address and control data in
DMA descriptor fields memory_pointer and ctrl_data_ptr
To fix warning: cast to pointer from integer of different size
Signed-off-by: Vasyl Gomonovych <gomonovych@gmail.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
We are currently using nand_soft_waitrdy to poll the status of the NAND
flash. FMC2 enables the wait feature bit (this feature is mandatory for
the sequencer mode). By enabling this feature, we can't poll the status
of the NAND flash, the read status command is stucked in FMC2 pipeline
until R/B# signal is high, and locks the CPU bus.
To avoid to lock the CPU bus, we poll FMC2 ISR register. This register
reports the status of the R/B# signal.
Fixes: 2cd457f328 ("mtd: rawnand: stm32_fmc2: add STM32 FMC2 NAND flash controller driver")
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
ioremap has provided non-cached semantics by default since the Linux 2.6
days, so remove the additional ioremap_nocache interface.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Here is the "big" tty and serial driver patches for 5.5-rc1. It's a bit
later in the merge window than normal as I wanted to make sure some
last-minute patches applied to it were all sane. They seem to be :)
There's a lot of little stuff in here, for the tty core, and for lots of
serial drivers:
- reverts of uartlite serial driver patches that were wrong
- msm-serial driver fixes
- serial core updates and fixes
- tty core fixes
- serial driver dma mapping api changes
- lots of other tiny fixes and updates for serial drivers
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXebFIQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylnmACgjfMcfQWa7uC9Q6m2DaQaRMaW6QoAnjg+TgBB
eW9EhvyXL2VbrsuUl+iH
=Am9O
-----END PGP SIGNATURE-----
Merge tag 'tty-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here is the "big" tty and serial driver patches for 5.5-rc1.
It's a bit later in the merge window than normal as I wanted to make
sure some last-minute patches applied to it were all sane. They seem
to be :)
There's a lot of little stuff in here, for the tty core, and for lots
of serial drivers:
- reverts of uartlite serial driver patches that were wrong
- msm-serial driver fixes
- serial core updates and fixes
- tty core fixes
- serial driver dma mapping api changes
- lots of other tiny fixes and updates for serial drivers
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (58 commits)
Revert "serial/8250: Add support for NI-Serial PXI/PXIe+485 devices"
vcs: prevent write access to vcsu devices
tty: vt: keyboard: reject invalid keycodes
tty: don't crash in tty_init_dev when missing tty_port
serial: stm32: fix clearing interrupt error flags
tty: Fix Kconfig indentation, continued
serial: serial_core: Perform NULL checks for break_ctl ops
tty: remove unused argument from tty_open_by_driver()
tty: Fix Kconfig indentation
{tty: serial, nand: onenand}: samsung: rename to fix build warning
serial: ifx6x60: add missed pm_runtime_disable
serial: pl011: Fix DMA ->flush_buffer()
Revert "serial-uartlite: Move the uart register"
Revert "serial-uartlite: Add get serial id if not provided"
Revert "serial-uartlite: Do not use static struct uart_driver out of probe()"
Revert "serial-uartlite: Add runtime support"
Revert "serial-uartlite: Change logic how console_port is setup"
Revert "serial-uartlite: Use allocated structure instead of static ones"
tty: serial: msm_serial: Use dma_request_chan() directly for channel request
tty: serial: tegra: Use dma_request_chan() directly for channel request
...
Any arm config which has 'CONFIG_MTD_ONENAND_SAMSUNG=m' and
'CONFIG_SERIAL_SAMSUNG=m' gives a build warning:
warning: same module names found:
drivers/tty/serial/samsung.ko
drivers/mtd/nand/onenand/samsung.ko
Rename both drivers/tty/serial/samsung.c to
drivers/tty/serial/samsung_tty.c and drivers/mtd/nand/onenand/samsung.c
drivers/mtd/nand/onenand/samsung_mtd.c to fix the warning.
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Acked-by: Richard Weinberger <richard@nod.at>
Link: https://lore.kernel.org/r/20191117202435.28127-1-sudipm.mukherjee@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Useless extra checks dropped.
* Updated the detection of the bad block markers position
Raw NAND controller drivers:
* Cadence : New driver
* Brcmnand: Support for flash-dma v0 + fixes
* Denali : Support for the legacy controller/chip DT representation
dropped
* Superfluous dev_err() calls removed
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAl3KwQYACgkQJWrqGEe9
VoTj1wf/Zvnk1u2vNVUaWDaHnUTAcMvjYNr1N1ppXquRXQTknZHxcgqavcwOA3yV
inHRdjQpvTPft3Pb0tddC2VBOMQTYWDGJs6JOLiPF5c4QdW/w4yHRrdnEIumbVP/
itXySbPj2QsXcRuIoEm165NTI8mdSzZFixZvCNS58r2mvMXvQbcUHsP9vjlUs9/S
XPqBlSBPKa6hC2ToIiXhgkGDQzVJ/OkCOSgG+37ATUrEqWUi9oN2KUPkbk4HSZe9
dntUIFSjeAqGjKGRGwAlt4axhnFWABfWa9xBwX9k5s4mt/FJ9QF24geemz/F1Ljp
7xd6MJu3JYoW8qBcXRRDgHuv5RNnHA==
=rpUJ
-----END PGP SIGNATURE-----
Merge tag 'nand/for-5.5' into mtd/next
Raw NAND core
* Useless extra checks dropped.
* Updated the detection of the bad block markers position
Raw NAND controller drivers:
* Cadence : New driver
* Brcmnand: Support for flash-dma v0 + fixes
* Denali : Support for the legacy controller/chip DT representation
dropped
* Superfluous dev_err() calls removed
- introduce 'struct spi_nor_controller_ops',
- clean the Register Operations methods,
- use dev_dbg insted of dev_err for low level info,
- fix retlen handling in sst_write(),
- fix silent truncations in spi_nor_read and spi_nor_read_raw(),
- fix the clearing of QE bit on lock()/unlock(),
- rework the disabling of the block write protection,
- rework the Quad Enable methods,
- make sure nor->spimem and nor->controller_ops are mutually exclusive,
- set default Quad Enable method for ISSI flashes,
- add support for few flashes.
SPI NOR controller drivers changes:
- intel-spi:
- support chips without software sequencer,
- add support for Intel Cannon Lake and Intel Comet Lake-H flashes.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEHUIqys8OyG1eHf7fS1VPR6WNFOkFAl3Kep8ACgkQS1VPR6WN
FOn9kgf/aKPgU6LR84YpwUKRZ4S+6K1H8SdDUt8v0FYSQ6oaTjF13fApg43WDja5
Zk0l5tlX7WIvlcRC6XKPhryZTXOKWojW1X8sguPYIZGzo7q82Eyda23jkw1QptWr
VO9L/tdK4yVUbdtp6VS/FUF31PC0DtDoCzsfBSUgrZP2srFF1BtOJNUgyuDceoxo
y3hEmINDnkaOvDDl/kbJjdEHG4PV8Vi4k0KE8deLpqlp8GDG1nkTeA1Sim7WjBPA
ZZOdg9fmGI8H8+umQEnn06H4O95T2+fX+kDMCYo4RbgWyWlGv5TidgRREmC/cSbl
YEPu6LCQoUZPVEvgolr/8Akf968ZiQ==
=i15M
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-5.5' into mtd/next
SPI NOR core changes:
- introduce 'struct spi_nor_controller_ops',
- clean the Register Operations methods,
- use dev_dbg insted of dev_err for low level info,
- fix retlen handling in sst_write(),
- fix silent truncations in spi_nor_read and spi_nor_read_raw(),
- fix the clearing of QE bit on lock()/unlock(),
- rework the disabling of the block write protection,
- rework the Quad Enable methods,
- make sure nor->spimem and nor->controller_ops are mutually exclusive,
- set default Quad Enable method for ISSI flashes,
- add support for few flashes.
SPI NOR controller drivers changes:
- intel-spi:
- support chips without software sequencer,
- add support for Intel Cannon Lake and Intel Comet Lake-H flashes.
Remove unecessary checking if dmac is NULL.
If Cadence nand controller driver uses DMA engine then cdns_ctrl->dmac
cannot be NULL. It is verified during driver initialization.
If Cadence nand controller driver does not use DMA engine then
CPU IO read/write are executed instead of slave DMA transfer.
In that case cdns_ctrl->dmac is not used at all.
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Piotr Sroka <piotrs@cadence.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
platform_get_irq() will call dev_err() itself on failure,
so there is no need for the driver to also do this.
This is detected by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
platform_get_irq() will call dev_err() itself on failure,
so there is no need for the driver to also do this.
This is detected by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Sparse complained about the following:
drivers/mtd/nand/raw/brcmnand/brcmnand.c:921:40: warning: Using plain integer as NULL pointer
fix this issue by assigning the pointer to NULL.
Fixes: c1ac2dc34b ("mtd: rawnand: brcmnand: When oops in progress use pio and interrupt polling")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Commit d8e8fd0ebf ("mtd: rawnand: denali: decouple controller and
NAND chips") supported the new binding for the separate controller/chip
representation, keeping the backward compatibility.
All the device trees in upstream migrated to the new binding.
Remove the support for the old binding.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: linux-mtd@lists.infradead.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Commit 7e534323c4 ("mtd: rawnand: Pass a nand_chip object to
chip->read_xxx() hooks") modified the prototype of the struct nand_chip
read_buf function pointer. In the au1550nd driver we have 2
implementations of read_buf. The previously mentioned commit modified
the au_read_buf() implementation to match the function pointer, but not
au_read_buf16(). This results in a compiler warning for MIPS
db1xxx_defconfig builds:
drivers/mtd/nand/raw/au1550nd.c:443:57:
warning: pointer type mismatch in conditional expression
Fix this by updating the prototype of au_read_buf16() to take a struct
nand_chip pointer as its first argument, as is expected after commit
7e534323c4 ("mtd: rawnand: Pass a nand_chip object to chip->read_xxx()
hooks").
Note that this shouldn't have caused any functional issues at runtime,
since the offset of the struct mtd_info within struct nand_chip is 0
making mtd_to_nand() effectively a type-cast.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: 7e534323c4 ("mtd: rawnand: Pass a nand_chip object to chip->read_xxx() hooks")
Cc: stable@vger.kernel.org # v4.20+
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add new Cadence NAND driver to MTD subsystem
Signed-off-by: Piotr Sroka <piotrs@cadence.com>
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Change calculating of position page containing BBM
If none of BBM flags are set then function nand_bbm_get_next_page
reports EINVAL. It causes that BBM is not read at all during scanning
factory bad blocks. The result is that the BBT table is build without
checking factory BBM at all. For Micron flash memories none of these
flags are set if page size is different than 2048 bytes.
Address this regression by:
- adding NAND_BBM_FIRSTPAGE chip flag without any condition. It solves
issue only for Micron devices.
- changing the nand_bbm_get_next_page_function. It will return 0
if no of BBM flag is set and page parameter is 0. After that modification
way of discovering factory bad blocks will work similar as in kernel
version 5.1.
Cc: stable@vger.kernel.org
Fixes: f90da7818b (mtd: rawnand: Support bad block markers in first, second or last page)
Signed-off-by: Piotr Sroka <piotrs@cadence.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
- boot_mem_map is removed, providing a nice cleanup made possible by the
recent removal of bootmem.
- Some fixes to atomics, in general providing compiler barriers for
smp_mb__{before,after}_atomic plus fixes specific to Loongson CPUs or
MIPS32 systems using cmpxchg64().
- Conversion to the new generic VDSO infrastructure courtesy of Vincenzo
Frascino.
- Removal of undefined behavior in set_io_port_base(), fixing the
behavior of some MIPS kernel configurations when built with recent
clang versions.
- Initial MIPS32 huge page support, functional on at least Ingenic SoCs.
- pte_special() is now supported for some configurations, allowing among
other things generic fast GUP to be used.
- Miscellaneous fixes & cleanups.
And platform specific changes:
- Major improvements to Ingenic SoC support from Paul Cercueil, mostly
enabled by the inclusion of the new TCU (timer-counter unit) drivers
he's spent a very patient year or so working on. Plus some fixes for
X1000 SoCs from Zhou Yanjie.
- Netgear R6200 v1 systems are now supported by the bcm47xx platform.
- DT updates for BMIPS, Lantiq & Microsemi Ocelot systems.
-----BEGIN PGP SIGNATURE-----
iIsEABYIADMWIQRgLjeFAZEXQzy86/s+p5+stXUA3QUCXYaqpRUccGF1bC5idXJ0
b25AbWlwcy5jb20ACgkQPqefrLV1AN2JUQD+PQGFIlq9bo/3vLyqsXJffm+DhwVQ
4WSCSeN5brPkO8EA/153sRJBlRtG+KK5p9f7WYKUuBfbcEawuc1uwmKuy7cG
=lWlM
-----END PGP SIGNATURE-----
Merge tag 'mips_5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS updates from Paul Burton:
"Main MIPS changes:
- boot_mem_map is removed, providing a nice cleanup made possible by
the recent removal of bootmem.
- Some fixes to atomics, in general providing compiler barriers for
smp_mb__{before,after}_atomic plus fixes specific to Loongson CPUs
or MIPS32 systems using cmpxchg64().
- Conversion to the new generic VDSO infrastructure courtesy of
Vincenzo Frascino.
- Removal of undefined behavior in set_io_port_base(), fixing the
behavior of some MIPS kernel configurations when built with recent
clang versions.
- Initial MIPS32 huge page support, functional on at least Ingenic
SoCs.
- pte_special() is now supported for some configurations, allowing
among other things generic fast GUP to be used.
- Miscellaneous fixes & cleanups.
And platform specific changes:
- Major improvements to Ingenic SoC support from Paul Cercueil,
mostly enabled by the inclusion of the new TCU (timer-counter unit)
drivers he's spent a very patient year or so working on. Plus some
fixes for X1000 SoCs from Zhou Yanjie.
- Netgear R6200 v1 systems are now supported by the bcm47xx platform.
- DT updates for BMIPS, Lantiq & Microsemi Ocelot systems"
* tag 'mips_5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (89 commits)
MIPS: Detect bad _PFN_SHIFT values
MIPS: Disable pte_special() for MIPS32 with RiXi
MIPS: ralink: deactivate PCI support for SOC_MT7621
mips: compat: vdso: Use legacy syscalls as fallback
MIPS: Drop Loongson _CACHE_* definitions
MIPS: tlbex: Remove cpu_has_local_ebase
MIPS: tlbex: Simplify r3k check
MIPS: Select R3k-style TLB in Kconfig
MIPS: PCI: refactor ioc3 special handling
mips: remove ioremap_cachable
mips/atomic: Fix smp_mb__{before,after}_atomic()
mips/atomic: Fix loongson_llsc_mb() wreckage
mips/atomic: Fix cmpxchg64 barriers
MIPS: Octeon: remove duplicated include from dma-octeon.c
firmware: bcm47xx_nvram: Allow COMPILE_TEST
firmware: bcm47xx_nvram: Correct size_t printf format
MIPS: Treat Loongson Extensions as ASEs
MIPS: Remove dev_err() usage after platform_get_irq()
MIPS: dts: mscc: describe the PTP ready interrupt
MIPS: dts: mscc: describe the PTP register range
...
* Fixing typos
* Adding missing of_node_put() in various drivers
Raw NAND controller drivers:
* Macronix: new controller driver
* Omap2: Fixing the number of bitflips returned
* Brcmnand: Fix a pointer not iterating over all the page chunks
* W90x900: Driver removed
* Onenand: Fix a memory leak
* Sharpsl: Missing include guard
* STM32: Avoid warnings when building with W=1
* Ingenic: Fix a coccinelle warning
* r852: Call a helper to simplify the code
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAl1ny0EACgkQJWrqGEe9
VoSToQf9Gk13+TPg8oFu6tlmxuQlNU5Dpc+4Hmiahzb1IWwo9Deh2VtZaeWLqPob
uAisb1HByUD0shgoG6cgmVajULlFpmTdfwBQCPR1Wgvq5pejoOC1MQOMexaZ7Gjx
cj4DZEk15FFSR7/zSsN78kFDLFh590hUGfBLW55qE69M5xphmb42BVQUFn44Q/N2
yBvqwUQO/h8TsOS4FXGNc1X0U2/wYQQSOZ6grN3x105cY8Rp05T15a+Qxu22cBem
5IqPY4dwOTXjY5l0mHVIiO/Jk/N9bAgMSd1a15VVukiAL3oefH/kNpsI8T5d31f2
uNONC6GhRJj8c3GDmO8gZ6skzTPhIg==
=a6jq
-----END PGP SIGNATURE-----
Merge tag 'nand/for-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux into mtd/for-5.4
NAND core
* Fixing typos
* Adding missing of_node_put() in various drivers
Raw NAND controller drivers:
* Macronix: new controller driver
* Omap2: Fixing the number of bitflips returned
* Brcmnand: Fix a pointer not iterating over all the page chunks
* W90x900: Driver removed
* Onenand: Fix a memory leak
* Sharpsl: Missing include guard
* STM32: Avoid warnings when building with W=1
* Ingenic: Fix a coccinelle warning
* r852: Call a helper to simplify the code
omap_elm_correct_data() returns the number of bitflips for the whole
page. This is wrong, it should return the maximum number of bitflips
found in each ECC step.
In my case with a 4k page size NAND mtcdore reported -EUCLEAN with
only 12 bitflips on a page where we could correct up to 128 bits per
page (provided they are distributed equally on the 8 ECC steps)
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
In brcmstb_nand_verify_erased_page(), the ECC chunk pointer calculation
while correcting erased page bitflips is wrong, fix it.
Fixes: 02b88eea9f ("mtd: brcmnand: Add check for erased page bitflips")
Signed-off-by: Claire Lin <claire.lin@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The ARM w90x900 platform is getting removed, so this driver is obsolete.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add a driver for Macronix raw NAND controller.
Signed-off-by: Mason Yang <masonccyang@mxic.com.tw>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
In nand_scan_bbt(), a temporary buffer 'buf' is allocated through
vmalloc(). However, if check_create() fails, 'buf' is not deallocated,
leading to a memory leak bug. To fix this issue, free 'buf' before
returning the error.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
In onenand_scan(), if CONFIG_MTD_ONENAND_VERIFY_WRITE is defined,
'this->verify_buf' is allocated through kzalloc(). However, it is not
deallocated in the following execution, if the allocation for
'this->oob_buf' fails, leading to a memory leak bug. To fix this issue,
free 'this->verify_buf' before returning the error.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Variable ret is being initialized with a value that is never read
and ret is being re-assigned a little later on. The assignment is
redundant and hence can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Instead of using to_pci_dev + pci_get_drvdata,
use dev_get_drvdata to make code simpler.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
drivers/mtd/nand/raw/ingenic/ingenic_nand_drv.c:330:1-9: WARNING: Use devm_platform_ioremap_resource for cs -> base
Use devm_platform_ioremap_resource helper which wraps
platform_get_resource() and devm_ioremap_resource() together.
Generated by: scripts/coccinelle/api/devm_platform_ioremap_resource.cocci
Fixes: c403ec33b6 ("mtd: rawnand: ingenic: Fix ingenic_ecc dependency")
CC: Paul Cercueil <paul@crapouillou.net>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
- Fix Micron driver as some chips enable internal ECC correction
during their discovery while they advertize they do not have any.
Hyperbus:
- Restrict the build to only ARM64 SoCs (and compile testing) which is
what should have been done since the beginning.
- Fix Kconfig issue by selection something instead of implying it.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAl1E0XAACgkQJWrqGEe9
VoSVXAf/XyLI00EIj3L2KF8K8iYLPRN+lfbeN/YrFvFd9WYhyjY82NKQ/7A1WVjB
k5VIJx4StnhvVBFj/amviK4NycZcJ8GXz5eQvd5oQYRP5pZ9rBBeed/7QAdQ1uEJ
s8yZyFZKQblFyqTISDsfAmiRmwPipAn5TrBRPvpN094tSxoz8MB4SLvRsUy4FIrr
zj6wGrIbSu2x/G3KUw7yTDAfL9QOdgHaCnmM04TOndoDPC+38yVs8ca/67AP44Ni
j0cYivMZhVpavx2n3G01WUiyXAgkDilaG3F+Tn6754zxfQhJM5tVzZOiwSCBI9FS
Cg2dgcRXfPlJJuD5Vs7aPFIGJHLEFg==
=TWEV
-----END PGP SIGNATURE-----
Merge tag 'mtd/fixes-for-5.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD fixes from Miquel Raynal:
"NAND:
- Fix Micron driver as some chips enable internal ECC correction
during their discovery while they advertize they do not have any.
Hyperbus:
- Restrict the build to only ARM64 SoCs (and compile testing) which
is what should have been done since the beginning.
- Fix Kconfig issue by selection something instead of implying it"
* tag 'mtd/fixes-for-5.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux:
mtd: hyperbus: Add hardware dependency to AM654 driver
mtd: hyperbus: Kconfig: Fix HBMC_AM654 dependencies
mtd: rawnand: micron: handle on-die "ECC-off" devices correctly
Some devices are not supposed to support on-die ECC but experience
shows that internal ECC machinery can actually be enabled through the
"SET FEATURE (EFh)" command, even if a read of the "READ ID Parameter
Tables" returns that it is not.
Currently, the driver checks the "READ ID Parameter" field directly
after having enabled the feature. If the check fails it returns
immediately but leaves the ECC on. When using buggy chips like
MT29F2G08ABAGA and MT29F2G08ABBGA, all future read/program cycles will
go through the on-die ECC, confusing the host controller which is
supposed to be the one handling correction.
To address this in a common way we need to turn off the on-die ECC
directly after reading the "READ ID Parameter" and before checking the
"ECC status".
Cc: stable@vger.kernel.org
Fixes: dbc44edbf8 ("mtd: rawnand: micron: Fix on-die ECC detection logic")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
It has been replaced with the newer Ingenic NAND driver.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Artur Rojek <contact@artur-rojek.eu>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
This patch fixes the following warning:
drivers/mtd/nand/onenand/onenand_base.c: In function ‘onenand_check_features’:
drivers/mtd/nand/onenand/onenand_base.c:3264:17: warning: this statement may fall through [-Wimplicit-fallthrough=]
this->options |= ONENAND_HAS_NOP_1;
drivers/mtd/nand/onenand/onenand_base.c:3265:2: note: here
case ONENAND_DEVICE_DENSITY_4Gb:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Cc: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Each iteration of for_each_child_of_node puts the previous node, but in
the case of a return from the middle of the loop, there is no put, thus
causing a memory leak. Hence add an of_node_put before the return.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Each iteration of for_each_child_of_node puts the previous node, but in
the case of a return from the middle of the loop, there is no put, thus
causing a memory leak. Hence add an of_node_put before the return.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Acked-by: Liang Yang <liang.yang@amlogic.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Each iteration of for_each_child_of_node puts the previous node, but in
the case of a return from the middle of the loop, there is no put, thus
causing a memory leak. Hence add an of_node_put before the return.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Acked-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Each iteration of for_each_child_of_node puts the previous node, but in
the case of a goto from the middle of the loop, there is no put, thus
causing a memory leak. Hence add an of_node_put under a new goto to put
the node at a loop exit.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Each iteration of for_each_available_child_of_node puts the previous
node, but in the case of a goto from the middle of the loop, there is no
put, thus causing a memory leak. Hence add an of_node_put before the
goto.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This patch solves warnings detected by setting W=1 when building.
Warnings type detected:
drivers/mtd/nand/raw/stm32_fmc2_nand.c: In function ‘stm32_fmc2_calc_timings’:
drivers/mtd/nand/raw/stm32_fmc2_nand.c:1417:23: warning: comparison is
always false due to limited range of data type [-Wtype-limits]
else if (tims->twait > FMC2_PMEM_PATT_TIMING_MASK)
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Cc: stable@vger.kernel.org
Fixes: 2cd457f328 ("mtd: rawnand: stm32_fmc2: add STM32 FMC2 NAND flash controller driver")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
While I was tempted to move it to admin-guide, as some docs
there are more userspace-faced, there are some very technical
discussions about memory error correction code from the Kernel
implementer's PoV. So, let's place it inside the driver-api
book.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Rename the mtd documentation files to ReST, add an
index for them and adjust in order to produce a nice html
output via the Sphinx build system.
It should be noticed that Sphinx doesn't handle very well
URLs with dots in the middle. Thankfully, internally, the '.'
char is translated to %2E, so we can jus use %2E instead of
dots, and this will work fine on both text and processed files.
At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
MTD core changes:
- New Hyperbus framework
- New _is_locked (concat) implementation
- Various cleanups
NAND core changes:
- use longest matching pattern in ->exec_op() default parser
- export NAND operation tracer
- add flag to indicate panic_write in MTD
- use kzalloc() instead of kmalloc() and memset()
Raw NAND controller drivers changes:
- brcmnand:
* fix BCH ECC layout for large page NAND parts
* fallback to detected ecc-strength, ecc-step-size
* when oops in progress use pio and interrupt polling
* code refactor code to introduce helper functions
* add support for v7.3 controller
- FSMC:
* use nand_op_trace for operation tracing
- GPMI:
* move all driver code into single file
* various cleanups (including dmaengine changes)
* use runtime PM to manage clocks
* implement exec_op
- MTK:
* correct low level time calculation of r/w cycle
* improve data sampling timing for read cycle
* add validity check for CE# pin setting
* fix wrongly assigned OOB buffer pointer issue
* re-license MTK NAND driver as Dual MIT/GPL
- STM32:
* manage the get_irq error case
* increase DMA completion timeouts
Raw NAND chips drivers changes:
- Macronix: add read-retry support
Onenand driver changes:
- add support for 8Gb datasize chips
- avoid fall-through warnings
SPI-NAND changes:
- define macros for page-read ops with three-byte addresses
- add support for two-byte device IDs and then for GigaDevice
GD5F1GQ4UFxxG
- add initial support for Paragon PN26G0xA
- handle the case where the last page read has bitflips
SPI-NOR core changes:
- add support for the mt25ql02g and w25q16jv flashes
- print error in case of jedec read id fails
- is25lp256: add post BFPT fix to correct the addr_width
SPI NOR controller drivers changes:
- intel-spi: Add support for Intel Elkhart Lake SPI serial flash
- smt32: remove the driver as the driver was replaced by spi-stm32-qspi.c
- cadence-quadspi: add reset control
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAl0qLr4ACgkQJWrqGEe9
VoQVCwf/ZCG5CldS3cs6B68kMJoZ/rJyJxBnxtIhffda2vw1KG/12o6XaDO9xA/R
EwYrOTzlYZxzCZsNvWyHepG3Kj3d38CJ52ZqhavjpihwMlKKOgW/K39xuKWCrfxS
sVMLz/UdrcsQfcPGAy7DSyqhzRAtupNxngCdEkIIMGFZWsv4uZfOFEGMrzUJ5RYN
/okIyUE7Iz0dRq1/KXSl365V1MS8QP2eHFuHrUd38+kJ8TJnQjXX3Bmdul4aNTx+
HIIpykovoAn5BZ0YA4lJL90zVoDOWysARwHIAMDvJa8zS0wDTU16Tj2M6AQK+a4x
hbIOOkeX0hTKpJvy7/khli5y1bn2mw==
=L+tV
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Miquel Raynal:
"This contains the following changes for MTD:
MTD core changes:
- New Hyperbus framework
- New _is_locked (concat) implementation
- Various cleanups
NAND core changes:
- use longest matching pattern in ->exec_op() default parser
- export NAND operation tracer
- add flag to indicate panic_write in MTD
- use kzalloc() instead of kmalloc() and memset()
Raw NAND controller drivers changes:
- brcmnand:
- fix BCH ECC layout for large page NAND parts
- fallback to detected ecc-strength, ecc-step-size
- when oops in progress use pio and interrupt polling
- code refactor code to introduce helper functions
- add support for v7.3 controller
- FSMC:
- use nand_op_trace for operation tracing
- GPMI:
- move all driver code into single file
- various cleanups (including dmaengine changes)
- use runtime PM to manage clocks
- implement exec_op
- MTK:
- correct low level time calculation of r/w cycle
- improve data sampling timing for read cycle
- add validity check for CE# pin setting
- fix wrongly assigned OOB buffer pointer issue
- re-license MTK NAND driver as Dual MIT/GPL
- STM32:
- manage the get_irq error case
- increase DMA completion timeouts
Raw NAND chips drivers changes:
- Macronix: add read-retry support
Onenand driver changes:
- add support for 8Gb datasize chips
- avoid fall-through warnings
SPI-NAND changes:
- define macros for page-read ops with three-byte addresses
- add support for two-byte device IDs and then for GigaDevice
GD5F1GQ4UFxxG
- add initial support for Paragon PN26G0xA
- handle the case where the last page read has bitflips
SPI-NOR core changes:
- add support for the mt25ql02g and w25q16jv flashes
- print error in case of jedec read id fails
- is25lp256: add post BFPT fix to correct the addr_width
SPI NOR controller drivers changes:
- intel-spi: Add support for Intel Elkhart Lake SPI serial flash
- smt32: remove the driver as the driver was replaced by spi-stm32-qspi.c
- cadence-quadspi: add reset control"
* tag 'mtd/for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (60 commits)
mtd: concat: implement _is_locked mtd operation
mtd: concat: refactor concat_lock/concat_unlock
mtd: abi: do not use C++ style comments in uapi header
mtd: afs: remove unneeded NULL check
mtd: rawnand: stm32_fmc2: increase DMA completion timeouts
mtd: rawnand: Use kzalloc() instead of kmalloc() and memset()
mtd: hyperbus: Add driver for TI's HyperBus memory controller
mtd: spinand: read returns badly if the last page has bitflips
mtd: spinand: Add initial support for Paragon PN26G0xA
mtd: rawnand: mtk: Re-license MTK NAND driver as Dual MIT/GPL
mtd: rawnand: gpmi: remove double assignment to block_size
dt-bindings: mtd: brcmnand: Add brcmnand, brcmnand-v7.3 support
mtd: rawnand: brcmnand: Add support for v7.3 controller
mtd: rawnand: brcmnand: Refactored code to introduce helper functions
mtd: rawnand: brcmnand: When oops in progress use pio and interrupt polling
mtd: Add flag to indicate panic_write
mtd: rawnand: Add Macronix NAND read retry support
mtd: onenand: Avoid fall-through warnings
mtd: spinand: Add support for GigaDevice GD5F1GQ4UFxxG
mtd: spinand: Add support for two-byte device IDs
...
Allwinner NAND controllers can make use of DMA to enhance the I/O
throughput thanks to ECC pipelining. DMA handling with A23/A33 NAND IP
is a bit different than with the older SoCs, hence the introduction of
a new compatible to handle:
* the differences between register offsets,
* the burst length change from 4 to minimum 8,
* manage SRAM accesses through MBUS with extra configuration.
Fixes: c49836f05a ("mtd: rawnand: sunxi: Add A23/A33 DMA support")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This reverts commit c49836f05a.
The commit is wrong and its approach actually does not work. Let's
revert it in order to add the feature with a clean patch.
Fixes: c49836f05a ("mtd: rawnand: sunxi: Add A23/A33 DMA support")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
If MTD_NAND_JZ4780 is y and MTD_NAND_JZ4780_BCH is m,
which select CONFIG_MTD_NAND_INGENIC_ECC to m, building fails:
drivers/mtd/nand/raw/ingenic/ingenic_nand.o: In function `ingenic_nand_remove':
ingenic_nand.c:(.text+0x177): undefined reference to `ingenic_ecc_release'
drivers/mtd/nand/raw/ingenic/ingenic_nand.o: In function `ingenic_nand_ecc_correct':
ingenic_nand.c:(.text+0x2ee): undefined reference to `ingenic_ecc_correct'
To fix that, the ingenic_nand and ingenic_ecc modules have been fused
into one single module.
- The ingenic_ecc.c code is now compiled in only if
$(CONFIG_MTD_NAND_INGENIC_ECC) is set. This is now a boolean instead
of tristate.
- To avoid changing the module name, the ingenic_nand.c file is moved to
ingenic_nand_drv.c. Then the module name is still ingenic_nand.
- Since ingenic_ecc.c is no more a module, the module-specific macros
have been dropped, and the functions are no more exported for use by
the ingenic_nand driver.
Fixes: 15de8c6efd ("mtd: rawnand: ingenic: Separate top-level and SoC specific code")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Reported-by: Hulk Robot <hulkci@huawei.com>
Cc: YueHaibing <yuehaibing@huawei.com>
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The 1Gb Macronix chip can have a maximum of 20 bad blocks, while
the 2Gb version has twice as many blocks and therefore the maximum
number of bad blocks is 40.
The 4Gb GigaDevice GD5F4GQ4xA has twice as many blocks as its 2Gb
counterpart and therefore a maximum of 80 bad blocks.
Fixes: 377e517b5f ("mtd: nand: Add max_bad_eraseblocks_per_lun info to memorg")
Reported-by: Emil Lenngren <emil.lenngren@gmail.com>
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
When the system is overloaded, DMA data transfer completion occurs after
100ms. Increase the timeouts to let it the time to complete.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Replace kmalloc() by a memset() followed with a kzalloc().
There is a recommendation to use zeroing allocator
rather than allocator followed by memset(0) in
./scripts/coccinelle/api/alloc/zalloc-simple.cocci
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
In case of the last page containing bitflips (ret > 0),
spinand_mtd_read() will return that number of bitflips for the last
page while it should instead return max_bitflips like it does when the
last page read returns with 0.
Signed-off-by: Weixiong Liao <liaoweixiong@allwinnertech.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Cc: stable@vger.kernel.org
Fixes: 7529df4652 ("mtd: nand: Add core infrastructure to support SPI NANDs")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
It is wanted to use MTK NAND driver with GPL-2.0 or MIT license.
But now it is only licensed as GPL-2.0, so re-license it as dual
MIT/GPL.
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Acked-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Acked-by: Ryder Lee <ryder.lee@mediatek.com>
Acked-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Boris Brezillon <boris.brezillon@collabora.com>
Acked-by: Wen Yang <yellowriver2010@hotmail.com>
Acked-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: RogerCC Lin <rogercc.lin@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The variable block_size is being assigned to itself and to
geo->ecc_chunk_size. Clean up the double assignment by removing
the assignment to itself.
Addresses-Coverity: ("Evaluation order violation")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This change adds support for brcm NAND v7.3 controller. This controller
uses a newer version of flash_dma engine and change mostly implements
these differences.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Refactored NAND ECC and CMD address configuration code to use helper
functions.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
If mtd_oops is in progress, switch to polling during NAND command
completion instead of relying on DMA/interrupts so that the mtd_oops
buffer can be completely written in the assigned NAND partition.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add support for Macronix NAND read retry.
Macronix NANDs support specific read operation for data recovery,
which can be enabled with a SET_FEATURE.
Driver checks byte 167 of Vendor Blocks in ONFI parameter page table
to see if this high-reliability function is supported.
Signed-off-by: Mason Yang <masonccyang@mxic.com.tw>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
NOTICE THAT:
"...we don't know whether we need fallthroughs or breaks here and this
is just a change to avoid having new warnings when switching to
-Wimplicit-fallthrough but this change might be entirely wrong."[1]
See the original thread of discussion here:
https://lore.kernel.org/patchwork/patch/1036251/
So, in preparation to enabling -Wimplicit-fallthrough, this patch silences
the following warnings:
drivers/mtd/nand/onenand/onenand_base.c: In function ‘onenand_check_features’:
drivers/mtd/nand/onenand/onenand_base.c:3264:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (ONENAND_IS_DDP(this))
^
drivers/mtd/nand/onenand/onenand_base.c:3284:2: note: here
case ONENAND_DEVICE_DENSITY_2Gb:
^~~~
drivers/mtd/nand/onenand/onenand_base.c:3288:17: warning: this statement may fall through [-Wimplicit-fallthrough=]
this->options |= ONENAND_HAS_UNLOCK_ALL;
drivers/mtd/nand/onenand/onenand_base.c:3290:2: note: here
case ONENAND_DEVICE_DENSITY_1Gb:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
Also, notice that this patch doesn't change any functionality. See the
most recent thread of discussion here:
https://lore.kernel.org/patchwork/patch/1077395/
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
[1] https://lore.kernel.org/lkml/20190509085318.34a9d4be@xps13/
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Suggested-by: Boris Brezillon <boris.brezillon@collabora.com>
Suggested-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The GigaDevice GD5F1GQ4UFxxG SPI NAND is in current production devices
and, while it has the same logical layout as the E-series devices,
it differs in the SPI interfacing in significant ways.
This support is contingent on previous commits to:
* Add support for two-byte device IDs
* Define macros for page-read ops with three-byte addresses
http://www.gigadevice.com/datasheet/gd5f1gq4xfxxg/
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This change supports nand-ecc-step-size and nand-ecc-strength fields in
brcmnand DT node to be optional.
see: Documentation/devicetree/bindings/mtd/brcm,brcmnand.txt
If both nand-ecc-strength and nand-ecc-step-size are not specified in
device tree node for NAND, raw NAND layer does detect ECC information by
reading ONFI extended parameter page for parts using ONFI >= 2.1.
In case of non-ONFI NAND parts there could be a nand_id table entry with
ECC information. If there is valid device tree entry for nand-ecc-strength
and nand-ecc-step-size fields it still shall override the detected values.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The gpmi driver performance suffers from NAND operations being split
in multiple small DMA transfers. This has been forced by the NAND layer
in the former days, but now with exec_op we can use the controller as
intended.
With this patch gpmi_nfc_exec_op becomes the main entry point to NAND
operations. Here all instructions are collected and chained as separate
DMA transfers. In the end whole chain is fired and waited to be
finished. gpmi_nfc_exec_op only does the hardware operations, bad block
marker swapping and buffer scrambling is done by the callers. It's worth
noting that the nand_*_op functions always take the buffer lengths for
the data that the NAND chip actually transfers. When doing BCH we have
to calculate the net data size from the raw data size in some places.
This patch has been tested with 2048/64 and 2048/128 byte NAND on
i.MX6q. mtd_oobtest, mtd_subpagetest and mtd_speedtest run without
errors. nandbiterrs, nandpagetest and nandsubpagetest userspace tests
from mtdutils run without errors and UBIFS can successfully be mounted.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The mxs dma driver uses the flags parameter in dmaengine_prep_slave_sg() for
custom flags, but still uses the dmaengine specific names of the flags.
Do a little bit better and at least give the flag a custom name.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The mxs dma driver can do PIO transfers. A pointer to the PIO words
to transfer is passed in the struct scatterlist * argument of
dmaengine_prep_slave_sg(). It's quite ugly and non obvious to cast
u32 * to struct scatterlist * each time when calling
dmaengine_prep_slave_sg(), so add a static inline wrapper function
to be called by the user along with a description what is going on.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The DMA_PREP_INTERRUPT flag is no longer needed by the mxs DMA driver,
drop it.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The gpmi driver aggressively en/disables the clocks between operations
which has significant performance cost. Use runtime PM to get rid of
this bottleneck.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The i.MX23 specific option read code is called right after nand_scan. We
can rely on the NAND core having disabled the chipselect, so there's no
point in restoring the original chip select after NAND operations. Drop
it.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
gpmi_ecc_read_page_data uses the page parameter only for a debug printf,
so we can drop the parameter and the debug printf. Moving the oob
delivery from gpmi_ecc_read_page_data to gpmi_ecc_read_page makes the
oob_required parameter unnecessary aswell.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The driver calls nand_read_page_op without a buffer passed and then
calls chip->legacy.read_buf to read the buffer afterwards which is
the same as passing the buffer nand_read_page_op in the first place.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
this->page_buffer_virt and this->payload_virt are always set to the same
value, so drop the former and just use the latter. Same for
this->page_buffer_virt and this->payload_virt.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The "private" member of struct gpmi_nand_data isn't used anywhere.
Remove it.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This moves the whole driver into a single C file. The filename gpmi-lib
implies that it implements library functions, but in fact there are
several cases where functions in gpmi-lib.c call back into functions in
gpmi-nand.c. With this one has to constantly jump between those two
files, so moving it into a single file improves readability, even when
the file gets quite large.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Replace the different operation tracing functions with a call to
nand_op_trace.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The NAND core has a NAND operation tracing function, but it can only
be used by drivers using the generic option parser from the NAND core.
Export the tracing function as a static inline function in rawnand.h
so that drivers implementing exec_op directly do not have to write their
own operation tracing.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
One main goal of the function mtk_nfc_update_ecc_stats is to check
whether sectors are all empty. If they are empty, set these sectors's
data buffer and OOB buffer as 0xff.
But now, the sector OOB buffer pointer is wrongly assigned. We always
do memset from sector 0.
To fix this issue, pass start sector number to make OOB buffer pointer
be properly assigned.
Fixes: 1d6b1e4649 ("mtd: mediatek: driver for MTK Smart Device")
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Currently, we only check how many CE# pins are set in device tree.
But it should be necessary to check whether CE# pin setting is
duplicated or if CE# pin index exceeds the maximum CE# number that
controller supports.
So, add validity check to avoid these invalid settings.
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Currently, we expand RE# low level time by choosing the max value
between RE# pulse width and RE# access time, and sample data at the
rising edge of RE#.
Then, if RE# access time is bigger than RE# pulse width, the real
read cycle time may be more than NAND SPEC required. This makes
read performance be worse than that expected.
This patch improves data sampling timing by calculating RE# low level
time according to RE# pulse width. If RE# access time is bigger than
RE# pulse width, then delay sampling data timing.
The result of contrast test base on MT2712 evaluat board is as follow.
nand: Micron MT29F16G08ADBCAH4
nand: 2048 MiB, SLC, erase size: 256 KiB, page size: 4096, OOB size: 224
NFI 2x clock rate: 124800000 HZ.
Read speed without this patch:
mtd_speedtest: page read speed is 14012 KiB/s
mtd_speedtest: 2 page read speed is 14860 KiB/s
Read speed with this patch:
mtd_speedtest: page read speed is 18724 KiB/s
mtd_speedtest: 2 page read speed is 18713 KiB/s
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
At present, the flow of calculating AC timing of read/write cycle in SDR
mode is that:
At first, calculate high hold time which is valid for both read and write
cycle using the max value between tREH_min and tWH_min.
Secondly, calculate WE# pulse width using tWP_min.
Thridly, calculate RE# pulse width using the bigger one between tREA_max
and tRP_min.
But NAND SPEC shows that Controller should also meet write/read cycle time.
That is write cycle time should be more than tWC_min and read cycle should
be more than tRC_min. Obviously, we do not achieve that now.
This patch corrects the low level time calculation to meet minimum
read/write cycle time required. After getting the high hold time, WE# low
level time will be promised to meet tWP_min and tWC_min requirement,
and RE# low level time will be promised to meet tREA_max, tRP_min and
tRC_min requirement.
Fixes: edfee3619c ("mtd: nand: mtk: add ->setup_data_interface() hook")
Cc: stable@vger.kernel.org # v4.17+
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The way oobregion->offset is derived for large page NAND parts is
wrong, fixes it.
Fixes: ef5eeea6e9 ("mtd: nand: brcm: switch to mtd_ooblayout_ops")
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Used in several S5PV210-based Galaxy S devices, among them SGH-T959V,
SGH-T959P, SGH-T839, and SPH-D700.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Sometimes the exec_op parser does not choose the optimal pattern if
multiple patterns with optional elements are available. Since the stack
automatically splits operations in multiple exec_op calls, a non-optimal
pattern gets broken up into multiple calls. E.g. an OOB read using the
vf610 driver:
nand: executing subop:
nand: ->CMD [0x00]
nand: ->ADDR [5 cyc: 00 08 ea 94 02]
nand: ->CMD [0x30]
nand: ->WAITRDY [max 200000 ms]
nand: DATA_IN [64 B]
nand: executing subop:
nand: CMD [0x00]
nand: ADDR [5 cyc: 00 08 ea 94 02]
nand: CMD [0x30]
nand: WAITRDY [max 200000 ms]
nand: ->DATA_IN [64 B]
However, the vf610 driver has a pattern which can execute the complete
command in a single go...
This patch makes sure that the longest matching pattern is chosen
instead of the first (potentially only partial) match. With this
change the vf610 reads the OOB in a single exec_op call:
nand: executing subop:
nand: ->CMD [0x00]
nand: ->ADDR [5 cyc: 00 08 c0 1d 00]
nand: ->CMD [0x30]
nand: ->WAITRDY [max 200000 ms]
nand: ->DATA_IN [64 B]
Reported-by: Sascha Hauer <s.hauer@pengutronix.de>
Suggested-by: Boris Brezillon <boris.brezillon@collabora.com>
Tested-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
- Fix a bug uncovered by a recent patch on Spansion SPI-NOR flashes.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAl0Pwk0ACgkQJWrqGEe9
VoS8nwf7B76jN39/g32Hfp4JT/B7cntrHzTGxfUT9NAhKa4MaI7FOU2eeTryaVdO
32OJlttV+r0Fu6p+In1VXCk4j1YlkcOaxqB1VXsMEaQ+Vt8ONVTbJX/cqyGC/ogq
MZlO8Rys4MGmq7vRiZ+1SD8lOV4qXgmX3D38NjUQ1oCAMCCgJgkWYFV2tv9Eie09
2CCT3IBFj+D34qaBiM+qocGtnzWfB9477A6ZeI4BwjUe1ZtoEYeIOrCXWiywabjM
msHRN1tNt5kfINnx0TkQFcnpbdDo5tMyTHCkEQt5Ewdae4vyCv7xTHTCZEttC7Ic
Rx2yONzrZGQVP4c27y22K954C1jGcg==
=ZiPm
-----END PGP SIGNATURE-----
Merge tag 'mtd/fixes-for-5.2-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull mtd fixes from Miquel Raynal:
- Set the raw NAND number of targets to the right value
- Fix a bug uncovered by a recent patch on Spansion SPI-NOR flashes
* tag 'mtd/fixes-for-5.2-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux:
mtd: spi-nor: use 16-bit WRR command when QE is set on spansion flashes
mtd: rawnand: initialize ntargets with maxchips
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation version 2 of the license
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 315 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Armijn Hemel <armijn@tjaldur.nl>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190115.503150771@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not write to the free
software foundation inc 59 temple place suite 330 boston ma 02111
1307 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 136 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190530000436.384967451@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program see the file copying if not
write to the free software foundation 59 temple place suite 330
boston ma 02111 1307 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 9 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190530000435.832876118@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this software is licensed under the terms of the gnu general public
license version 2 as published by the free software foundation and
may be copied distributed and modified under those terms this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 285 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.642774971@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 655 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070034.575739538@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 3 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [kishon] [vijay] [abraham]
[i] [kishon]@[ti] [com] this program is distributed in the hope that
it will be useful but without any warranty without even the implied
warranty of merchantability or fitness for a particular purpose see
the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [graeme] [gregory]
[gg]@[slimlogic] [co] [uk] [author] [kishon] [vijay] [abraham] [i]
[kishon]@[ti] [com] [based] [on] [twl6030]_[usb] [c] [author] [hema]
[hk] [hemahk]@[ti] [com] this program is distributed in the hope
that it will be useful but without any warranty without even the
implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1105 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.202006027@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation inc
59 temple place suite 330 boston ma 02111 1307 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1334 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.113240726@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version you should have received a copy of the
gnu general public license along with this program if not write to
the free software foundation inc 675 mass ave cambridge ma 02139 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 35 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Armijn Hemel <armijn@tjaldur.nl>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.655028468@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 or at your option any
later version this program is distributed in the hope that it will
be useful but without any warranty without even the implied warranty
of merchantability or fitness for a particular purpose see the gnu
general public license for more details you should have received a
copy of the gnu general public license along with this program if
not write to the free software foundation inc 59 temple place suite
330 boston ma 02111 1307 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 42 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190524100845.259718220@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation inc
675 mass ave cambridge ma 02139 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 441 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190520071858.739733335@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this file is free software you can redistribute it and or modify it
under the terms of the gnu general public license as published by
the free software foundation either version 2 or at your option any
later version this file is distributed in the hope that it will be
useful but without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details you should have received a
copy of the gnu general public license along with this file if not
write to the free software foundation inc 59 temple place suite 330
boston ma 02111 1307 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 2 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190520170858.735098607@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
memorg->ntargets is initialized with '1'. It should be initialized with
the maxchips argument from nand_scan() instead. Otherwise multi chip
support errors out on the secondary chip selects when trying to call
nand_reset() on them:
WARNING: CPU: 0 PID: 1 at drivers/mtd/nand/raw/internals.h:114
nand_reset_op+0x194/0x1c4
With this memorg->ntargets is initialized with the maximum number of
chip selects supported by the driver. After having detected the number
of actually connected chips memory->ntargets is updated with that
number.
Fixes: 32813e2884 ("mtd: rawnand: Get rid of chip->numchips")
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation inc
51 franklin street fifth floor boston ma 02110 1301 usa
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option [no]_[pad]_[ctrl] any later version this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not write to the free
software foundation inc 51 franklin street fifth floor boston ma
02110 1301 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 176 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154040.652910950@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all files which:
- Have no license information of any form
- Have MODULE_LICENCE("GPL*") inside which was used in the initial
scan/conversion to ignore the file
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This prepares to move CONFIG_OPTIMIZE_INLINING from x86 to a common
place. We need to eliminate potential issues beforehand.
Kbuild test robot has never reported -Wmaybe-uninitialized warning for
this probably because vf610_nfc_run() is inlined by the x86 compiler's
inlining heuristic.
If CONFIG_OPTIMIZE_INLINING is enabled for a different architecture and
vf610_nfc_run() is not inlined, the following warning is reported:
drivers/mtd/nand/raw/vf610_nfc.c: In function `vf610_nfc_cmd':
drivers/mtd/nand/raw/vf610_nfc.c:455:3: warning: `offset' may be used uninitialized in this function [-Wmaybe-uninitialized]
vf610_nfc_rd_from_sram(instr->ctx.data.buf.in + offset,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
nfc->regs + NFC_MAIN_AREA(0) + offset,
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
trfr_sz, !nfc->data_access);
~~~~~~~~~~~~~~~~~~~~~~~~~~~
Link: http://lkml.kernel.org/r/20190423034959.13525-6-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Boris Brezillon <bbrezillon@kernel.org>
Cc: Borislav Petkov <bp@suse.de>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mathieu Malaterre <malat@debian.org>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
MTD core changes:
- New AFS partition parser
- Update MAINTAINERS entry
- Use of fall-throughs markers
NAND core changes:
- Support having the bad block markers in either the first, second or
last page of a block. The combination of all three location is now
possible.
- Constification of NAND_OP_PARSER(_PATTERN) elements.
- Generic NAND DT bindings changed to yaml format (can be used to
check the proposed bindings. First platform to be fully supported:
sunxi.
- Stopped using several legacy hooks.
- Preparation to use the generic NAND layer with the addition of
several helpers and the removal of the struct nand_chip from generic
functions.
- Kconfig cleanup to prepare the introduction of external ECC engines
support.
- Fallthrough comments.
- Introduction of the SPI-mem dirmap API for SPI-NAND devices.
Raw NAND controller drivers changes:
- nandsim:
* Switch to ->exec-op().
- meson:
* Misc cleanups and fixes.
* New OOB layout.
- Sunxi:
* A23/A33 NAND DMA support.
- Ingenic:
* Full reorganization and cleanup.
* Clear separation between NAND controller and ECC engine.
* Support JZ4740 an JZ4725B.
- Denali:
* Clear controller/chip separation.
* ->exec_op() migration.
* Various cleanups.
- fsl_elbc:
* Enable software ECC support.
- Atmel:
* Sam9x60 support.
- GPMI:
* Introduce the GPMI_IS_MXS() macro.
- Various trivial/spelling/coding style fixes.
SPI NOR core changes:
- Print all JEDEC ID bytes on error
- Fix comment of spi_nor_find_best_erase_type()
- Add region locking flags for s25fl512s
SPI NOR controller drivers changes:
- intel-spi:
* Avoid crossing 4K address boundary on read/write
* Add support for Intel Comet Lake SPI serial flash
-----BEGIN PGP SIGNATURE-----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=HXap
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-5.2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Richard Weinberger:
"MTD core changes:
- New AFS partition parser
- Update MAINTAINERS entry
- Use of fall-throughs markers
NAND core changes:
- Support having the bad block markers in either the first, second or
last page of a block. The combination of all three location is now
possible.
- Constification of NAND_OP_PARSER(_PATTERN) elements.
- Generic NAND DT bindings changed to yaml format (can be used to
check the proposed bindings. First platform to be fully supported:
sunxi.
- Stopped using several legacy hooks.
- Preparation to use the generic NAND layer with the addition of
several helpers and the removal of the struct nand_chip from
generic functions.
- Kconfig cleanup to prepare the introduction of external ECC engines
support.
- Fallthrough comments.
- Introduction of the SPI-mem dirmap API for SPI-NAND devices.
Raw NAND controller drivers changes:
- nandsim:
- Switch to ->exec-op().
- meson:
- Misc cleanups and fixes.
- New OOB layout.
- Sunxi:
- A23/A33 NAND DMA support.
- Ingenic:
- Full reorganization and cleanup.
- Clear separation between NAND controller and ECC engine.
- Support JZ4740 an JZ4725B.
- Denali:
- Clear controller/chip separation.
- ->exec_op() migration.
- Various cleanups.
- fsl_elbc:
- Enable software ECC support.
- Atmel:
- Sam9x60 support.
- GPMI:
- Introduce the GPMI_IS_MXS() macro.
- Various trivial/spelling/coding style fixes.
SPI NOR core changes:
- Print all JEDEC ID bytes on error
- Fix comment of spi_nor_find_best_erase_type()
- Add region locking flags for s25fl512s
SPI NOR controller drivers changes:
- intel-spi:
- Avoid crossing 4K address boundary on read/write
- Add support for Intel Comet Lake SPI serial flash"
* tag 'mtd/for-5.2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (120 commits)
mtd: part: fix incorrect format specifier for an unsigned long long
mtd: lpddr_cmds: Mark expected switch fall-through
mtd: phram: Mark expected switch fall-throughs
mtd: cfi_cmdset_0002: Mark expected switch fall-throughs
mtd: cfi_util: mark expected switch fall-throughs
MAINTAINERS: MTD Git repository is hosted on kernel.org
MAINTAINERS: Update jffs2 entry
mtd: afs: add v2 partition parsing
mtd: afs: factor the IIS read into partition parser
mtd: afs: factor footer parsing into the v1 part parsing
mtd: factor out v1 partition parsing
mtd: afs: simplify partition detection
mtd: afs: simplify partition parsing
mtd: partitions: Add OF support to AFS partitions
mtd: partitions: Add AFS partitions DT bindings
mtd: afs: Move AFS partition parser to parsers subdir
mtd: maps: Make uclinux_ram_map static
mtd: maps: Allow MTD_PHYSMAP with MTD_RAM
MAINTAINERS: Add myself as MTD maintainer
MAINTAINERS: Remove my name from the MTD and NAND entries
...
Remove mmiowb() from the kernel memory barrier API and instead, for
architectures that need it, hide the barrier inside spin_unlock() when
MMIO has been performed inside the critical section.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEPxTL6PPUbjXGY88ct6xw3ITBYzQFAlzMFaUACgkQt6xw3ITB
YzRICQgAiv7wF/yIbBhDOmCNCAKDO59chvFQWxXWdGk/aAB56kwKAMXJgLOvlMG/
VRuuLyParTFQETC3jaxKgnO/1hb+PZLDt2Q2KqixtjIzBypKUPWvK2sf6THhSRF1
GK0DBVUd1rCrWrR815+SPb8el4xXtdBzvAVB+Fx35PXVNpdRdqCkK+EQ6UnXGokm
rXXHbnfsnquBDtmb4CR4r2beH+aNElXbdt0Kj8VcE5J7f7jTdW3z6Q9WFRvdKmK7
yrsxXXB2w/EsWXOwFp0SLTV5+fgeGgTvv8uLjDw+SG6t0E0PebxjNAflT7dPrbYL
WecjKC9WqBxrGY+4ew6YJP70ijLBCw==
=aC8m
-----END PGP SIGNATURE-----
Merge tag 'arm64-mmiowb' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull mmiowb removal from Will Deacon:
"Remove Mysterious Macro Intended to Obscure Weird Behaviours (mmiowb())
Remove mmiowb() from the kernel memory barrier API and instead, for
architectures that need it, hide the barrier inside spin_unlock() when
MMIO has been performed inside the critical section.
The only relatively recent changes have been addressing review
comments on the documentation, which is in a much better shape thanks
to the efforts of Ben and Ingo.
I was initially planning to split this into two pull requests so that
you could run the coccinelle script yourself, however it's been plain
sailing in linux-next so I've just included the whole lot here to keep
things simple"
* tag 'arm64-mmiowb' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (23 commits)
docs/memory-barriers.txt: Update I/O section to be clearer about CPU vs thread
docs/memory-barriers.txt: Fix style, spacing and grammar in I/O section
arch: Remove dummy mmiowb() definitions from arch code
net/ethernet/silan/sc92031: Remove stale comment about mmiowb()
i40iw: Redefine i40iw_mmiowb() to do nothing
scsi/qla1280: Remove stale comment about mmiowb()
drivers: Remove explicit invocations of mmiowb()
drivers: Remove useless trailing comments from mmiowb() invocations
Documentation: Kill all references to mmiowb()
riscv/mmiowb: Hook up mmwiob() implementation to asm-generic code
powerpc/mmiowb: Hook up mmwiob() implementation to asm-generic code
ia64/mmiowb: Add unconditional mmiowb() to arch_spin_unlock()
mips/mmiowb: Add unconditional mmiowb() to arch_spin_unlock()
sh/mmiowb: Add unconditional mmiowb() to arch_spin_unlock()
m68k/io: Remove useless definition of mmiowb()
nds32/io: Remove useless definition of mmiowb()
x86/io: Remove useless definition of mmiowb()
arm64/io: Remove useless definition of mmiowb()
ARM/io: Remove useless definition of mmiowb()
mmiowb: Hook up mmiowb helpers to spinlocks and generic I/O accessors
...
Since the migration of the driver to stop using the legacy
->select_chip() hook, there is nothing deselecting the target anymore,
thus the selection is not forced at the next access. Ensure the ND_RUN
bit and the interrupts are always in a clean state.
Cc: Daniel Mack <daniel@zonque.org>
Cc: stable@vger.kernel.org
Fixes: b25251414f ("mtd: rawnand: marvell: Stop implementing ->select_chip()")
Suggested-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Daniel Mack <daniel@zonque.org>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Stop using the legacy interface.
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
We will need struct nand_controller soon, so more stuff need to
be parts of struct nandsim.
While we are here, rename "nand" to "ns" to use the same naming scheme
everywhere in nandsim.
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
According to the datasheet of some Cypress SLC NANDs, the bad
block markers can be in the first, second or last page of a block.
So let's check all three locations.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Boris Brezillon <bbrezillon@kernel.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
It is known that some ESMT SLC NANDs have been shipped
with the factory bad block markers in the first or last page
of the block, instead of the first or second page. To be on
the safe side, let's check all three locations.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Boris Brezillon <bbrezillon@kernel.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Currently supported bad block marker positions within the block are:
* in first page only
* in last page only
* in first or second page
Some ESMT NANDs are known to have been shipped by the manufacturer
with bad block markers in the first or last page, instead of the
first or second page.
Also the datasheets for Cypress/Spansion/AMD NANDs claim that the
first, second *and* last page needs to be checked.
Therefore we make it possible to set NAND_BBM_FIRSTPAGE,
NAND_BBM_SECONDPAGE and NAND_BBM_LASTPAGE independently in any
combination.
To simplify the code, the logic to evaluate the flags is moved to a
a new function nand_bbm_get_next_page().
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
To be able to check and set bad block markers in the first and
second page of a block independently of each other, we create
separate flags for both cases.
Previously NAND_BBM_SECONDPAGE meant, that both, the first and the
second page were used. With this patch NAND_BBM_FIRSTPAGE stands for
using the first page and NAND_BBM_SECONDPAGE for using the second
page.
This patch is only for preparation of subsequent changes and does
not implement the logic to actually handle both flags separately.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Boris Brezillon <bbrezillon@kernel.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The information about where the manufacturer puts the bad block
markers inside the bad block and in the OOB data is stored in
different places. Let's move this information to the chip struct,
as we did it for rawnand.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The information about where the manufacturer puts the bad block
markers inside the bad block and in the OOB data is stored in
different places. Let's move this information to nand_chip.options
and nand_chip.badblockpos.
As this chip-specific information is not directly related to the
bad block table (BBT), we also rename the flags to NAND_BBM_*.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Documentation/scheduler/completion.txt states:
Calling init_completion() on the same completion object twice is
most likely a bug as it re-initializes the queue to an empty queue and
enqueued tasks could get "lost" - use reinit_completion() in that case,
but be aware of other races.
Initialize nfc->completion in meson_nfc_probe using init_completion and
change the call in meson_nfc_queue_rb to reinit_completion so the logic
matches what the documentation suggests.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by:Liang Yang <liang.yang@amlogic.com>
Acked-by: Liang Yang <liang.yang@amlogic.com>
Tested-by:Liang Yang <liang.yang@amlogic.com>
Acked-by: Liang Yang <liang.yang@amlogic.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This simplifies the code because it gets rid of the casts to an
u8-pointer when passing "info_buf" from struct meson_nfc_nand_chip.
Also it gets rid of the cast of the u8 databuf pointer to a void
pointer.
The logic inside meson_nfc_dma_buffer_setup() doesn't care about the
pointer types themselves because it only passes them to dma_map_single
which accepts a void pointer.
No functional changes.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by:Liang Yang <liang.yang@amlogic.com>
Acked-by: Liang Yang <liang.yang@amlogic.com>
Tested-by:Liang Yang <liang.yang@amlogic.com>
Acked-by: Liang Yang <liang.yang@amlogic.com>
Tested-by:Liang Yang <liang.yang@amlogic.com>
Acked-by: Liang Yang <liang.yang@amlogic.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Use the of_property_count_elems_of_size() helper instead of open-coding
it's logic. As a bonus this will now error out if the "reg" property
values use an incorrect size (anything other than sizeof(u32)).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by:Liang Yang <liang.yang@amlogic.com>
Acked-by: Liang Yang <liang.yang@amlogic.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Use the recently introduced struct_size macro instead of open-coding
it's logic.
No functional changes.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by:Liang Yang <liang.yang@amlogic.com>
Acked-by: Liang Yang <liang.yang@amlogic.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Since the migration of the driver to stop using the legacy
->select_chip() hook, the marvell_nfc_select_chip() helper has been
'renamed' to marvell_nfc_select_target(). Update a left-over reference
to this helper in a comment in the ->resume() path.
Fixes: b25251414f ("mtd: rawnand: marvell: Stop implementing ->select_chip()")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Allwinner NAND controllers can make use of DMA to enhance the I/O
throughput thanks to ECC pipelining. DMA handling with A23/A33 NAND IP
is a bit different than with the older SoCs, hence the introduction of
a new compatible to handle:
* the differences between register offsets,
* the burst length change from 4 to minimum 8,
* drive SRAM accesses through the AHB bus instead of the MBUS.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Before the introduction of A33 NAND DMA support, let's use a platform
data structure for parameters that will differ. Right now, there is
only one compatible with one data structure.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Fix sparse warning:
drivers/mtd/nand/raw/ingenic/ingenic_nand.c:140:32: warning:
symbol 'jz4725b_ooblayout_ops' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Eliminate the following reports from 'scripts/checkpatch.pl --strict'.
CHECK: Prefer kernel type 'u8' over 'uint8_t'
CHECK: Prefer kernel type 'u32' over 'uint32_t'
CHECK: Alignment should match open parenthesis
I slightly changed denali_check_erased_page() to shorten it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Use the runtime-detected denali->nbanks instead of hard-coded
DENALI_NR_BANKS (=4).
The actual number of banks depends on the IP configuration, and
can be less than DENALI_NR_BANKS. It is pointless to touch
registers of unsupported banks.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Currently, this driver sticks to the legacy NAND model because it was
upstreamed before commit 2d472aba15 ("mtd: nand: document the NAND
controller/NAND chip DT representation"). However, relying on the
dummy_controller is already deprecated.
Switch over to the new controller/chip representation.
The struct denali_nand_info has been split into denali_controller
and denali_chip, to contain the controller data, per-chip data,
respectively.
One problem is, this commit changes the DT binding. So, as always,
the backward compatibility must be taken into consideration.
In the new binding, the controller node expects
#address-cells = <1>;
#size-cells = <0>;
... since the child nodes represent NAND chips.
In the old binding, the controller node may have subnodes, but they
are MTD partitions.
The denali_dt_is_legacy_binding() exploits it to distinguish old/new
platforms.
Going forward, the old binding is only allowed for existing DT files.
I updated the binding document.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
As Documentation/process/coding-style.rst says, choose label names
which say what the goto does. The out_<action> label style is already
used in denali_dt.c. Rename likewise for denali_pci.c
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Use 'bool' type for the following boolean parameters.
- write (write or read?)
- dma_avail (DMA engine available or not?)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Since (u32 *) can accept an opaque pointer, the explicit casting
from (void *) to (u32 *) is redundant. Change the function argument type
to remove the casts.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The Denali IP adopts the syndrome page layout (payload and ECC are
interleaved). The *_page_raw() and *_oob() callbacks are complicated
because they must hide the underlying layout used by the hardware,
and always return contiguous in-band and out-of-band data.
The Denali IP cannot reuse nand_{read,write}_page_raw_syndrome()
in nand_base.c because its hardware ECC engine skips some of first
bytes in OOB. That is why this driver implements specially-crafted
*_page_raw() and *_oob() hooks.
Currently, similar code is duplicated to reorganize the data layout.
For example, denali_read_page_raw() and denali_write_page_raw() look
almost the same. The complexity is partly due to the DMA transfer
used for better performance of *_page_raw() accessors.
On second thought, we do not need to care about their performance
because MTD_OPS_RAW is rarely used.
Let's focus on code cleanups rather than the performance. This commit
removes the internal buffer for DMA, and factors out as much code as
possible.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
With the recent refactoring, the NAND driver hooks now take a pointer
to nand_chip. Add to_denali() in order to convert (struct nand_chip *)
to (struct denali_nand_info *) directly. It is more useful than the
current mtd_to_denali().
I changed some helper functions to take (struct nand_chip *). This will
avoid pointer conversion back and forth, and ease further development.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Wrong copy/paste from the previous block, the error message should
refer to #size-cells instead of #address-cells.
Fixes: f88fc122cc ("mtd: nand: Cleanup/rework the atmel_nand driver")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Move the code that choses ECC into _attach_chip, which is executed only
after the chip->ecc.* properties were loaded from device-tree. This way
we know which ECC method was chosen by the device-tree and can set
methods appropriately.
The chip->ecc.*page methods should be set to fsl_elbc_*page only in HW
ECC mode.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Move the fsl_elbc_attach_chip function after the definitions of
fsl_elbc_read_page and friends in preparation for the next patch.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
When enabling CONFIG_MTD_NAND_ECC_SW_BCH as a module, the
MTD_NAND_ECC_SW_BCH depends on MTD_NAND, but the module controlled by
MTD_NAND links against the module controlled by MTD_NAND_ECC_SW_BCH.
This leads to the following link failure.
aarch64-linux-gnu-ld: drivers/mtd/nand/raw/nand_base.o: in function `nand_cleanup':
../drivers/mtd/nand/raw/nand_base.c:5886: undefined reference to `nand_bch_free'
aarch64-linux-gnu-ld: ../drivers/mtd/nand/raw/nand_base.c:5886:(.text+0x9928): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `nand_bch_free'
aarch64-linux-gnu-ld: drivers/mtd/nand/raw/nand_base.o: in function `nand_set_ecc_soft_ops':
../drivers/mtd/nand/raw/nand_base.c:5093: undefined reference to `nand_bch_calculate_ecc'
aarch64-linux-gnu-ld: ../drivers/mtd/nand/raw/nand_base.c:5093:(.text+0xe914): relocation truncated to fit: R_AARCH64_ADR_PREL_PG_HI21 against undefined symbol `nand_bch_calculate_ecc'
aarch64-linux-gnu-ld: ../drivers/mtd/nand/raw/nand_base.c:5093: undefined reference to `nand_bch_calculate_ecc'
aarch64-linux-gnu-ld: ../drivers/mtd/nand/raw/nand_base.c:5094: undefined reference to `nand_bch_correct_data'
aarch64-linux-gnu-ld: ../drivers/mtd/nand/raw/nand_base.c:5094:(.text+0xe934): relocation truncated to fit: R_AARCH64_ADR_PREL_PG_HI21 against undefined symbol `nand_bch_correct_data'
aarch64-linux-gnu-ld: ../drivers/mtd/nand/raw/nand_base.c:5094: undefined reference to `nand_bch_correct_data'
aarch64-linux-gnu-ld: ../drivers/mtd/nand/raw/nand_base.c:5148: undefined reference to `nand_bch_init'
aarch64-linux-gnu-ld: ../drivers/mtd/nand/raw/nand_base.c:5148:(.text+0xebbc): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `nand_bch_init'
Rework CONFIG_MTD_NAND_ECC_SW_BCH from tristate to bool,
and then link the nand_bch.o file into nand.ko if its enabled.
Fixes: 51ef1d0b2095 ("mtd: nand: Clarify Kconfig entry for software BCH ECC algorithm")
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Prepare changes that will lay in this file to better express what is
NAND related and what is not in menuconfig.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
MTD_NAND is large and encloses much more than what the symbol is
actually used for: raw NAND. Clarify the symbol by naming it
MTD_RAW_NAND instead.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This list is a mess, while some items should probably not be in the
raw/ sub-directory, others are definitely at the right place but not
with the right description. Write uniform titles and group IPs by
vendor.
NAND controllers will appear under the list named "Raw/parallel NAND
flash controllers" while the other drivers will appear under
"Misc". Software ECC engines will later be moved out of the raw/
directory.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The software Hamming ECC correction implementation is referred as
MTD_NAND_ECC which is too generic. Rename it
MTD_NAND_ECC_SW_HAMMING. Also rename MTD_NAND_ECC_SMC which is an
SMC quirk in the Hamming implementation as
MTD_NAND_ECC_SW_HAMMING_SMC.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
There is no point in having two distinct entries, merge them and
rename the symbol for more clarity: MTD_NAND_ECC_SW_BCH
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
mmiowb() is now implied by spin_unlock() on architectures that require
it, so there is no reason to call it from driver code. This patch was
generated using coccinelle:
@mmiowb@
@@
- mmiowb();
and invoked as:
$ for d in drivers include/linux/qed sound; do \
spatch --include-headers --sp-file mmiowb.cocci --dir $d --in-place; done
NOTE: mmiowb() has only ever guaranteed ordering in conjunction with
spin_unlock(). However, pairing each mmiowb() removal in this patch with
the corresponding call to spin_unlock() is not at all trivial, so there
is a small chance that this change may regress any drivers incorrectly
relying on mmiowb() to order MMIO writes between CPUs using lock-free
synchronisation. If you've ended up bisecting to this commit, you can
reintroduce the mmiowb() calls using wmb() instead, which should restore
the old behaviour on all architectures other than some esoteric ia64
systems.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
nand_device embeds a nand_ecc_req object which contains the minimum
strength and step-size required by the NAND device.
Drop the chip->ecc_{strength,step}_ds fields and use
chip->base.eccreq.{strength,step_size} instead.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
The same information is provided by nanddev_ntargets().
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
The target size can now be returned by nanddev_get_targetsize(). Get
rid of the chip->chipsize field and use this helper instead.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Now that we inherit from nand_device, we can use
nand_device->memorg.bits_per_cell instead of having our own field at
the nand_chip level.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
nanddev_mtd_max_bad_blocks() is implemented by the generic NAND layer
and is already doing what we need. Reuse this function instead of
having our own implementation.
While at it, get rid of the ->max_bb_per_die and ->blocks_per_die
fields which are now unused.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Looking at the field names it's hard to tell what ->data_buf, ->pagebuf
and ->pagebuf_bitflips are for. Clarify that by moving those fields
in a sub-struct named pagecache.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
We plan to move cache related fields to a pagecache struct in nand_chip
but some drivers access ->pagebuf directly to invalidate the cache
before they start using ->data_buf.
Let's provide an helper that returns a pointer to ->data_buf after
invalidating the cache.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
In order to use some of the nanddev_xxx() helpers, we need to
initialize the nand_device object embedded in nand_chip using
nanddev_init(). This requires implementing nand_ops.
We also drop useless mtd->xxx initialization when they're already taken
case of by nanddev_init().
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
If we want to use the generic NAND layer, we need to have the memorg
struct appropriately filled. Patch the detection code to fill this
struct.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
We just have to use nanddev_mtd_max_bad_blocks().
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
NAND datasheets usually give the maximum number of bad blocks per LUN
and this number can be used to help upper layers decide how much blocks
they should reserve for bad block handling.
Add a max_bad_eraseblocks_per_lun to the nand_memory_organization
struct and update the NAND_MEMORG() macro (and its users) accordingly.
We also provide a default mtd->_max_bad_blocks() implementation.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Specify the oob layout operation to avoid no oob scheme defined for
some nand flash.
Fixes: 8fae856c53 ("mtd: rawnand: meson: add support for Amlogic NAND flash controller")
Signed-off-by: Liang Yang <liang.yang@amlogic.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
of_match_device can return NULL if there is no matching device. Avoid
a potential NULL pointer dereference by checking for the return value
and passing the error upstream.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The generic layout for BBT markers will most likely overlap with our
ECC bytes in the OOB, so move the BBT markers outside the OOB area.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The Ben Nanonote from Qi Hardware expects a specific OOB layout on its
NAND.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The boot ROM of the JZ4725B SoC expects a specific OOB layout on the
NAND, so we use it unconditionally in the ingenic-nand driver.
Also add the jz4725b-bch driver to support the JZ4725B-specific BCH
hardware.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add support for probing the ingenic-nand driver on the JZ4740 SoC from
Ingenic, and the jz4740-ecc driver to support the JZ4740-specific
ECC hardware.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Use the 'ecc-engine' standard property instead of the custom
'ingenic,bch-controller' custom property, which is now deprecated.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The ingenic-nand driver uses an API provided by the jz4780-bch driver.
This makes it difficult to support other SoCs in the jz4780-bch driver.
To work around this, we separate the API functions from the SoC-specific
code, so that these API functions are SoC-agnostic.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The jz4780_bch_init name was confusing, as it suggested that its content
should be executed once at init time, whereas what the function really
does is reset the hardware for a new ECC operation.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The jz4780_nand driver will be modified to handle all the Ingenic
JZ47xx SoCs that the upstream Linux kernel supports (JZ4740, JZ4725B,
JZ4770, JZ4780), so it makes sense to rename it.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Use SPDX license notifiers instead of GPLv2 license text in the headers.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Before adding support for more SoCs and seeing the number of files for
these drivers grow, we move them to their own subfolder to keep it tidy.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
meson_nfc_dma_buffer_setup() is called with the "info" buffer which is
allocated a few lines before using kzalloc(). If
meson_nfc_dma_buffer_setup() fails we need to free the allocated "info"
buffer instead of only freeing it upon success.
Fixes: 8fae856c53 ("mtd: rawnand: meson: add support for Amlogic NAND flash controller")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Liang Yang <liang.yang@amlogic.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
kzalloc() can return NULL if memory could not be allocated. Check the
return value of the kzalloc() call in meson_nfc_read_buf() to make it
consistent with other memory allocations within the meson_nand driver.
Fixes: 8fae856c53 ("mtd: rawnand: meson: add support for Amlogic NAND flash controller")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Liang Yang <liang.yang@amlogic.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The sam9x60 board defines the CCFG_EBICSA register under SFR,
and not as a MATRIX register, as previous boards do.
NAND Flash I/Os are connected to D16–D23, thus
SFR_CCFG_EBICSA.NFD0_ON_D16 is set to 1.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The sam9x60 board defines the CCFG_EBICSA register under SFR,
and not as a MATRIX register, as previous boards do. Add a
more generic name for the EBICSA regmap, as a prerequisite for
sam9x60 nand controller support.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warning:
drivers/mtd/nand/raw/diskonchip.c: In function ‘doc_probe’:
./include/linux/printk.h:303:2: warning: this statement may fall through [-Wimplicit-fallthrough=]
printk(KERN_ERR pr_fmt(fmt), ##__VA_ARGS__)
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/mtd/nand/raw/diskonchip.c:1479:4: note: in expansion of macro ‘pr_err’
pr_err("DiskOnChip Millennium Plus 32MB is not supported, ignoring.\n");
^~~~~~
drivers/mtd/nand/raw/diskonchip.c:1480:3: note: here
default:
^~~~~~~
drivers/mtd/nand/raw/nandsim.c: In function ‘ns_init_module’:
drivers/mtd/nand/raw/nandsim.c:2254:22: warning: this statement may fall through [-Wimplicit-fallthrough=]
chip->bbt_options |= NAND_BBT_NO_OOB;
drivers/mtd/nand/raw/nandsim.c:2255:2: note: here
case 1:
^~~~
drivers/mtd/nand/raw/nuc900_nand.c: In function ‘nuc900_nand_command_lp’:
./arch/x86/include/asm/io.h:91:22: warning: this statement may fall through [-Wimplicit-fallthrough=]
#define __raw_writel __writel
drivers/mtd/nand/raw/nuc900_nand.c:52:2: note: in expansion of macro ‘__raw_writel’
__raw_writel((val), (dev)->reg + REG_SMCMD)
^~~~~~~~~~~~
drivers/mtd/nand/raw/nuc900_nand.c:196:3: note: in expansion of macro ‘write_cmd_reg’
write_cmd_reg(nand, NAND_CMD_READSTART);
^~~~~~~~~~~~~
drivers/mtd/nand/raw/nuc900_nand.c:197:2: note: here
default:
^~~~~~~
drivers/mtd/nand/raw/omap_elm.c: In function ‘elm_context_restore’:
drivers/mtd/nand/raw/omap_elm.c:512:4: warning: this statement may fall through [-Wimplicit-fallthrough=]
elm_write_reg(info, ELM_SYNDROME_FRAGMENT_4 + offset,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
regs->elm_syndrome_fragment_4[i]);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/mtd/nand/raw/omap_elm.c:514:3: note: here
case BCH8_ECC:
^~~~
drivers/mtd/nand/raw/omap_elm.c:517:4: warning: this statement may fall through [-Wimplicit-fallthrough=]
elm_write_reg(info, ELM_SYNDROME_FRAGMENT_2 + offset,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
regs->elm_syndrome_fragment_2[i]);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/mtd/nand/raw/omap_elm.c:519:3: note: here
case BCH4_ECC:
^~~~
drivers/mtd/nand/raw/omap_elm.c: In function ‘elm_context_save’:
drivers/mtd/nand/raw/omap_elm.c:466:37: warning: this statement may fall through [-Wimplicit-fallthrough=]
regs->elm_syndrome_fragment_4[i] = elm_read_reg(info,
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~
ELM_SYNDROME_FRAGMENT_4 + offset);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/mtd/nand/raw/omap_elm.c:468:3: note: here
case BCH8_ECC:
^~~~
drivers/mtd/nand/raw/omap_elm.c:471:37: warning: this statement may fall through [-Wimplicit-fallthrough=]
regs->elm_syndrome_fragment_2[i] = elm_read_reg(info,
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~
ELM_SYNDROME_FRAGMENT_2 + offset);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/mtd/nand/raw/omap_elm.c:473:3: note: here
case BCH4_ECC:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enabling
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Introduce a GPMI_IS_MXS() macro to take into account the cases
when mx23 or mx28 are used, which helps readability.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Make use of the spi-mem direct mapping API to let advanced controllers
optimize read/write operations when they support direct mapping.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Stefan Roese <sr@denx.de>
- Use struct_size() where appropriate
- mtd_{read,write}() as wrappers around mtd_{read,write}_oob()
- Fix misuse of PTR_ERR() in docg3
- Coding style improvements in mtdcore.c
SPI NOR changes:
Core changes:
- Add support of octal mode I/O transfer
- Add a bunch of SPI NOR entries to the flash_info table
SPI NOR controller driver changes:
- cadence-quadspi:
* Add support for Octal SPI controller
* write upto 8-bytes data in STIG mode
- mtk-quadspi:
* rename config to a common one
* add SNOR_HWCAPS_READ to spi_nor_hwcaps mask
- Add Tudor as SPI-NOR co-maintainer
NAND changes
NAND core changes:
- Fourth batch of fixes/cleanup to the raw NAND core impacting various
controller drivers (Sunxi, Marvell, MTK, TMIO, OMAP2).
- Checking the return code of nand_reset() and nand_readid_op().
- Removing ->legacy.erase and single_erase().
- Simplifying the locking.
- Several implicit fall through annotations.
Raw NAND controllers drivers changes:
- Fixing various possible object reference leaks (MTK, JZ4780, Atmel).
- ST:
* Adding support for STM32 FMC2 NAND flash controller.
- Meson:
* Adding support for Amlogic NAND flash controller.
- Denali:
* Several cleanup patches.
- Sunxi:
* Several cleanup patches.
- FSMC:
* Disabling NAND on remove().
* Resetting NAND timings on resume().
SPI-NAND drivers changes:
- Toshiba:
* Adding support for all Toshiba products.
- Macronix:
* Fixing ECC status read.
- Gigadevice:
* Adding support for GD5F1GQ4UExxG.
-----BEGIN PGP SIGNATURE-----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=wIHY
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-5.1' of git://git.infradead.org/linux-mtd
Pull MTD updates from Boris Brezillon:
"Core MTD changes:
- Use struct_size() where appropriate
- mtd_{read,write}() as wrappers around mtd_{read,write}_oob()
- Fix misuse of PTR_ERR() in docg3
- Coding style improvements in mtdcore.c
SPI NOR changes:
Core changes:
- Add support of octal mode I/O transfer
- Add a bunch of SPI NOR entries to the flash_info table
SPI NOR controller driver changes:
- cadence-quadspi:
* Add support for Octal SPI controller
* write upto 8-bytes data in STIG mode
- mtk-quadspi:
* rename config to a common one
* add SNOR_HWCAPS_READ to spi_nor_hwcaps mask
- Add Tudor as SPI-NOR co-maintainer
NAND changes:
NAND core changes:
- Fourth batch of fixes/cleanup to the raw NAND core impacting
various controller drivers (Sunxi, Marvell, MTK, TMIO, OMAP2).
- Check the return code of nand_reset() and nand_readid_op().
- Remove ->legacy.erase and single_erase().
- Simplify the locking.
- Several implicit fall through annotations.
Raw NAND controllers drivers changes:
- Fix various possible object reference leaks (MTK, JZ4780, Atmel)
- ST:
* Add support for STM32 FMC2 NAND flash controller
- Meson:
* Add support for Amlogic NAND flash controller
- Denali:
* Several cleanup patches
- Sunxi:
* Several cleanup patches
- FSMC:
* Disable NAND on remove()
* Reset NAND timings on resume()
SPI-NAND drivers changes:
- Toshiba:
* Add support for all Toshiba products.
- Macronix:
* Fix ECC status read.
- Gigadevice:
* Add support for GD5F1GQ4UExxG"
* tag 'mtd/for-5.1' of git://git.infradead.org/linux-mtd: (64 commits)
mtd: spi-nor: Fix wrong abbreviation HWCPAS
mtd: spi-nor: cadence-quadspi: fix spelling mistake: "Couldnt't" -> "Couldn't"
mtd: spi-nor: Add support for en25qh64
mtd: spi-nor: Add support for MX25V8035F
mtd: spi-nor: Add support for EN25Q80A
mtd: spi-nor: cadence-quadspi: Add support for Octal SPI controller
dt-bindings: cadence-quadspi: Add new compatible for AM654 SoC
mtd: spi-nor: split s25fl128s into s25fl128s0 and s25fl128s1
mtd: spi-nor: cadence-quadspi: write upto 8-bytes data in STIG mode
mtd: spi-nor: Add support for mx25u3235f
mtd: rawnand: denali_dt: remove single anonymous clock support
mtd: rawnand: mtk: fix possible object reference leak
mtd: rawnand: jz4780: fix possible object reference leak
mtd: rawnand: atmel: fix possible object reference leak
mtd: rawnand: fsmc: Disable NAND on remove()
mtd: rawnand: fsmc: Reset NAND timings on resume()
mtd: spinand: Add support for GigaDevice GD5F1GQ4UExxG
mtd: rawnand: denali: remove unused dma_addr field from denali_nand_info
mtd: rawnand: denali: remove unused function argument 'raw'
mtd: rawnand: denali: remove unneeded denali_reset_irq() call
...
Commit 6f1fe97bec ("mtd: rawnand: denali_dt: add more clocks based
on IP datasheet") introduced a more correct binding that requires
three named clocks.
Now that all upstream DT files migrated over to it, remove the single
anonymous clock support.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Dinh Nguyen <dinguyen@kernel.org>
Acked-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
of_find_device_by_node() takes a reference to the struct device
when it finds a match via get_device, there is no need to call
get_device() twice.
We also should make sure to drop the reference to the device
taken by of_find_device_by_node() on driver unbind.
Fixes: 1d6b1e4649 ("mtd: mediatek: driver for MTK Smart Device")
Signed-off-by: Wen Yang <yellowriver2010@hotmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
of_find_device_by_node() takes a reference to the struct device
when it finds a match via get_device, there is no need to call
get_device() twice.
We also should make sure to drop the reference to the device
taken by of_find_device_by_node() on driver unbind.
Fixes: ae02ab00aa ("mtd: nand: jz4780: driver for NAND devices on JZ4780 SoCs")
Signed-off-by: Wen Yang <yellowriver2010@hotmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
of_find_device_by_node() takes a reference to the struct device
when it finds a match via get_device, there is no need to call
get_device() twice.
We also should make sure to drop the reference to the device
taken by of_find_device_by_node() on driver unbind.
Fixes: f88fc122cc ("mtd: nand: Cleanup/rework the atmel_nand driver")
Signed-off-by: Wen Yang <yellowriver2010@hotmail.com>
Suggested-by: Boris Brezillon <bbrezillon@kernel.org>
Reviewed-by: Boris Brezillon <bbrezillon@kernel.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Tudor Ambarus <tudor.ambarus@microchip.com>
Cc: Boris Brezillon <bbrezillon@kernel.org>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: linux-mtd@lists.infradead.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Disable BCH soft reset according to MX23 erratum #2847 ("BCH soft
reset may cause bus master lock up") for MX28 too. It has the same
problem.
Observed problem: once per 100,000+ MX28 reboots NAND read failed on
DMA timeout errors:
[ 1.770823] UBI: attaching mtd3 to ubi0
[ 2.768088] gpmi_nand: DMA timeout, last DMA :1
[ 3.958087] gpmi_nand: BCH timeout, last DMA :1
[ 4.156033] gpmi_nand: Error in ECC-based read: -110
[ 4.161136] UBI warning: ubi_io_read: error -110 while reading 64
bytes from PEB 0:0, read only 0 bytes, retry
[ 4.171283] step 1 error
[ 4.173846] gpmi_nand: Chip: 0, Error -1
Without BCH soft reset we successfully executed 1,000,000 MX28 reboots.
I have a quote from NXP regarding this problem, from July 18th 2016:
"As the i.MX23 and i.MX28 are of the same generation, they share many
characteristics. Unfortunately, also the erratas may be shared.
In case of the documented erratas and the workarounds, you can also
apply the workaround solution of one device on the other one. This have
been reported, but I’m afraid that there are not an estimated date for
updating the Errata documents.
Please accept our apologies for any inconveniences this may cause."
Fixes: 6f2a6a5256 ("mtd: nand: gpmi: reset BCH earlier, too, to avoid NAND startup problems")
Cc: stable@vger.kernel.org
Signed-off-by: Manfred Schlaegl <manfred.schlaegl@ginzinger.com>
Signed-off-by: Martin Kepplinger <martin.kepplinger@ginzinger.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
This disables the NAND on remove() and the errorpath,
making sure the chipselect gets deasserted when the
NAND is not in use.
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
When we go through a suspend/resume cycle the NAND
timings and other settings may have been lost so reset
the chip to bring it up in a known working state.
The FSMC only supports single CS chips so we only need
to call nand_reset(chip, 0).
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This is a leftover of commit 997cde2a22 ("mtd: nand: denali: skip
driver internal bounce buffer when possible").
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This argument is not used at all.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This code was added by commit 26d266e10e ("mtd: nand: denali: fix
raw and oob accessors for syndrome page layout"), but I do not see
sensible reason.
The IRQ flags are correctly reset by denali_cmd_ctrl(), so this code
is unneeded.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
nand_scan_ident() iterates over maxchips to find as many homogeneous
chips as possible.
Since commit 2d472aba15 ("mtd: nand: document the NAND
controller/NAND chip DT representation"), new drivers should pass in
the exact number of CS lines instead of possible max, but old
platforms may still rely on nand_scan_ident() to detect the actual
number of connected CS lines.
In that case, this loop bails out when manufacturer or device ID
unmatches. The reason of unmatch is most likely no chip is connected
to that CS line. If so, nand_reset() should already have failed,
and the following nand_readid_op() is pointless.
Before ->exec_op hook was introduced, drivers had no way to tell
the failure of NAND_CMD_RESET to the framework because the legacy
->cmdfunc() has void return type. Now drivers implementing ->exec_op
hook can return the error code. You can save nand_readid_op() by
checking the return value of nand_reset(). The return value of
nand_readid_op() should be checked as well. If it fails, probably
id[0] and id[1] are undefined values.
Just for consistency, it should be sensible to check the return
code in nand_do_write_oob() as well.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Now that the last user of this hook, denali.c, stopped using it,
we can remove the erase hook from nand_legacy.
I squashed single_erase() because only the difference between
single_erase() and nand_erase_op() is the number of bit shifts.
The status/ret conversion in nand_erase_nand() is unneeded since
commit eb94555e9e ("mtd: nand: use usual return values for the
->erase() hook"). Cleaned it up now.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Commit f9ebd1bb41 ("mtd: rawnand: Deprecate ->erase()") discouraged
the use of this hook, so I am happy to follow the suggestion.
Although the Denali IP provides a special MAP10 command for erasing,
using it would not buy us much. The Denali IP actually works with the
generic erasing by single_erase() + ->cmdfunc hook (nand_command_lp)
+ ->cmd_ctrl hook (denali_cmd_ctrl).
This method is also deprecated, but denali_erase() can go away
irrespective of ->exec_op conversion.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
There is a plan to build the kernel with -Wimplicit-fallthrough and
these places in the code produced warnings (W=1).
This commit removes the following warnings:
drivers/mtd/nand/raw/nand_base.c:5556:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/mtd/nand/raw/nand_base.c:5575:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/mtd/nand/raw/nand_base.c:5613:13: warning: this statement may fall through [-Wimplicit-fallthrough=]
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
There is a plan to build the kernel with -Wimplicit-fallthrough and
these places in the code produced warnings (W=1).
This commit removes the following warnings:
drivers/mtd/nand/raw/nand_legacy.c:332:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/mtd/nand/raw/nand_legacy.c:483:3: warning: this statement may fall through [-Wimplicit-fallthrough=]
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add initial support for the Amlogic NAND flash controller which is
available on Meson SoCs.
Signed-off-by: Liang Yang <liang.yang@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Jianxin Pan <jianxin.pan@amlogic.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
nand_get_device() was complex for apparently no good reason. Let's
replace this locking scheme with 2 mutexes: one attached to the
controller and another one attached to the chip.
Every time the core calls nand_get_device(), it will first lock the
chip and if the chip is not suspended, will then lock the controller.
nand_release_device() will release both lock in the reverse order.
nand_get_device() can sleep, just like the previous implementation,
which means you should never call that from an atomic context.
We also get rid of
- the chip->state field, since all it was used for was flagging the
chip as suspended. We replace it by a field called chip->suspended
and directly set it from nand_suspend/resume()
- the controller->wq and controller->active fields which are no longer
needed since the new controller->lock (now a mutex) guarantees that
all operations are serialized at the controller level
- panic_nand_get_device() which would anyway be a no-op. Talking about
panic write, I keep thinking the rawnand implementation is unsafe
because there's not negotiation with the controller to know when it's
actually done with it's previous operation. I don't intend to fix
that here, but that's probably something we should look at, or maybe
we should consider dropping the ->_panic_write() implementation
Last important change to mention: we now return -EBUSY when someone
tries to access a device that as been suspended, and propagate this
error to the upper layer.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
We are about to simplify the locking in the rawnand framework, and part
of this simplication is about getting rid of chip->state, so let's
first patch drivers that check the state.
All of them do that to get a timeout value based on the operation that
is being executed. Since a timeout is, by definition, something that
is here to prevent hanging on an event that might never happen,
picking the maximum timeout value no matter the operation should be
harmless.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Stop initializing omap_gpmc_controller fields are declaration time and
replace that by a call to nand_controller_init(). Since the same object
might be shared by several NAND chips and the NAND controller driver
expects a ->probe() per-chip, we need to keep track of the
omap_gpmc_controller state (whether it's already been initialized or
not).
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
nand_controller->wq has never been meant to be used by NAND controller
drivers. This waitqueue is used by the framework to serialize accesses
to a NAND controller, and messing up with its state is a really bad
idea.
Declare a completion object in tmio_nand and use it to wait for RB
transitions.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
nand_controller_init() has been added to simplify nand_controller
struct initialization. Use this function instead of duplicating the
logic.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = devm_kzalloc(dev, sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = devm_kzalloc(dev, struct_size(instance, entry, count), GFP_KERNEL);
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
In non-EDO, tREA should be less than tRP to guarantee that the
controller does not sample the IO lines too early. Unfortunately, the
sunxi NAND controller does not allow us to have different values for
tRP and tREH (tRP = tREH = tRW / 2).
We have 2 options to overcome this limitation:
1/ Extend tRC to fulfil the tREA <= tRC / 2 constraint
2/ Use EDO mode (only works if timings->tRLOH > 0)
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The datasheet specifies the upper four bits are reserved.
Testing on real hardware shows that these bits can indeed be nonzero.
Signed-off-by: Emil Lenngren <emil.lenngren@gmail.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Fix the struct description and use standard kernel-doc header format
(even if the file is not parsed by the doc generator).
We also replace tabs by a single space.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
And get rif of all legacy hooks and unused fields.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Replace the license text by an SPDX tag and fix MODULE_LICENSE() to
match GPL-2.0+.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Replace them by nand_chip pointers.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
nand_chip objects are sometimes called chip and sometimes nand. Rename
all of them into nand to make things consistent.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Use struct_size() to calculate sunxi_nand object size.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
sunxi_nand_chip objects are sometimes called chip and other times
called sunxi_nand. Make that consistent and name all occurrences
sunxi_nand.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This patch adds the polling mode, a basic mode that do not need
any DMA channels. This mode is also useful for debug purpose.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The driver adds the support for the STMicroelectronics FMC2 NAND
Controller found on STM32MP SOCs.
This patch is based on FMC2 command sequencer.
The purpose of the command sequencer is to facilitate the programming
and the reading of NAND flash pages with the ECC and to free the CPU
of sequencing tasks.
It requires one DMA channel for write and two DMA channels for read
operations.
Only NAND_ECC_HW mode is actually supported.
The driver supports a maximum 8k page size.
The following ECC strength and step size are currently supported:
- nand-ecc-strength = <8>, nand-ecc-step-size = <512> (BCH8)
- nand-ecc-strength = <4>, nand-ecc-step-size = <512> (BCH4)
- nand-ecc-strength = <1>, nand-ecc-step-size = <512> (Extended ECC
based on Hamming)
This patch has been tested on Micron MT29F8G08ABACAH4 and
MT29F8G16ABACAH4
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Fix kernel-doc warnings in drivers/mtd/nand/raw:
../drivers/mtd/nand/raw/nand_base.c:420: warning: Function parameter or member 'chip' not described in 'nand_fill_oob'
../drivers/mtd/nand/raw/nand_bbt.c:173: warning: Function parameter or member 'this' not described in 'read_bbt'
../drivers/mtd/nand/raw/nand_bbt.c:173: warning: Excess function parameter 'chip' description in 'read_bbt'
Fixes: 0813621ba8 ("mtd: rawnand: Stop passing mtd_info objects to internal functions")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Boris Brezillon <boris.brezillon@bootlin.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: linux-mtd@lists.infradead.org
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
The manufacturer specific initialization has already been done when
block unlocking takes place, and if anything goes wrong during this
procedure we should call spinand_manufacturer_cleanup().
Fixes: 7529df4652 ("mtd: nand: Add core infrastructure to support SPI NANDs")
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Looks like PROGRAM LOAD (AKA write cache) does not necessarily reset
the cache content to 0xFF (depends on vendor implementation), so we
must fill the page cache entirely even if we only want to program the
data portion of the page, otherwise we might corrupt the BBM or user
data previously programmed in OOB area.
Fixes: 7529df4652 ("mtd: nand: Add core infrastructure to support SPI NANDs")
Reported-by: Stefan Roese <sr@denx.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Tested-by: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
The function jz_nand_ioremap_resource() needs a pointer to an __iomem
pointer as its last argument but this argument is declared as:
void * __iomem *base
Fix this by using the correct declaration:
void __iomem **base
which then also removes the following Sparse's warnings:
282:15: warning: incorrect type in assignment (different address spaces)
282:15: expected void *[noderef] <asn:2>
282:15: got void [noderef] <asn:2> *
322:57: warning: incorrect type in argument 4 (different address spaces)
322:57: expected void *[noderef] <asn:2> *base
322:57: got void [noderef] <asn:2> **
402:67: warning: incorrect type in argument 4 (different address spaces)
402:67: expected void *[noderef] <asn:2> *base
402:67: got void [noderef] <asn:2> **
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Hammering the "bank enable" (PBKEN) bit on and off between
every command crashes the Nomadik NHK15 with this message:
Scanning device for bad blocks
Unhandled fault: external abort on non-linefetch (0x008) at 0xcc95e000
pgd = (ptrval)
[cc95e000] *pgd=0b808811, *pte=40000653, *ppte=40000552
Internal error: : 8 [#1] PREEMPT ARM
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 4.20.0-rc2+ #72
Hardware name: Nomadik STn8815
PC is at fsmc_exec_op+0x194/0x204
(...)
After a discussion we (me and Boris Brezillon) start to suspect
that this bit does not immediately control the chip select line
at all, it rather enables access to the bank and the hardware
will drive the CS autonomously. If there is a NAND chip connected,
we should keep this enabled.
As fsmc_nand_setup() sets this bit, we can simply remove the
offending code.
Fixes: 550b9fc4e3 ("mtd: rawnand: fsmc: Stop implementing ->select_chip()")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
This patch fixes a memory corruption that occurred in the
qcom-nandc driver since it was converted to nand_scan().
On boot, an affected device will panic from a NPE at a weird place:
| Unable to handle kernel NULL pointer dereference at virtual address 0
| pgd = (ptrval)
| [00000000] *pgd=00000000
| Internal error: Oops: 80000005 [#1] SMP ARM
| CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.19.9 #0
| Hardware name: Generic DT based system
| PC is at (null)
| LR is at nand_block_isbad+0x90/0xa4
| pc : [<00000000>] lr : [<c0592240>] psr: 80000013
| sp : cf839d40 ip : 00000000 fp : cfae9e20
| r10: cf815810 r9 : 00000000 r8 : 00000000
| r7 : 00000000 r6 : 00000000 r5 : 00000001 r4 : cf815810
| r3 : 00000000 r2 : cfae9810 r1 : ffffffff r0 : cf815810
| Flags: Nzcv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
| Control: 10c5387d Table: 8020406a DAC: 00000051
| Process swapper/0 (pid: 1, stack limit = 0x(ptrval))
| [<c0592240>] (nand_block_isbad) from [<c0580a94>]
| [<c0580a94>] (allocate_partition) from [<c05811e4>]
| [<c05811e4>] (add_mtd_partitions) from [<c0581164>]
| [<c0581164>] (parse_mtd_partitions) from [<c057def4>]
| [<c057def4>] (mtd_device_parse_register) from [<c059d274>]
| [<c059d274>] (qcom_nandc_probe) from [<c0567f00>]
The problem is that the nand_scan()'s qcom_nand_attach_chip callback
is updating the nandc->max_cwperpage from 1 to 4. This causes the
sg_init_table of clear_bam_transaction() in the driver's
qcom_nandc_block_bad() to memset much more than what was initially
allocated by alloc_bam_transaction().
This patch restores the old behavior by reallocating the shared bam
transaction alloc_bam_transaction() after the chip was identified,
but before mtd_device_parse_register() (which is an alias for
mtd_device_register() - see panic) gets called. This fixes the
corruption and the driver is working again.
Cc: stable@vger.kernel.org
Fixes: 6a3cec64f1 ("mtd: rawnand: qcom: convert driver to nand_scan()")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
- Parse the 4BAIT SFDP section
- Add a bunch of SPI NOR entries to the flash_info table
- Add the concept of SFDP fixups and use it to fix a bug on MX25L25635F
- A bunch of minor cleanups/comestic changes
-----BEGIN PGP SIGNATURE-----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=JXhP
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-4.21' of git://git.infradead.org/linux-mtd into mtd/next
Core changes:
- Parse the 4BAIT SFDP section
- Add a bunch of SPI NOR entries to the flash_info table
- Add the concept of SFDP fixups and use it to fix a bug on MX25L25635F
- A bunch of minor cleanups/comestic changes
NAND core changes:
- kernel-doc miscellaneous fixes.
- Third batch of fixes/cleanup to the raw NAND core impacting various
controller drivers (ams-delta, marvell, fsmc, denali, tegra, vf610):
* Stopping to pass mtd_info objects to internal functions
* Reorganizing code to avoid forward declarations
* Dropping useless test in nand_legacy_set_defaults()
* Moving nand_exec_op() to internal.h
* Adding nand_[de]select_target() helpers
* Passing the CS line to be selected in struct nand_operation
* Making ->select_chip() optional when ->exec_op() is implemented
* Deprecating the ->select_chip() hook
* Moving the ->exec_op() method to nand_controller_ops
* Moving ->setup_data_interface() to nand_controller_ops
* Deprecating the dummy_controller field
* Fixing JEDEC detection
* Providing a helper for polling GPIO R/B pin
Raw NAND chip drivers changes:
- Macronix:
* Flagging 1.8V AC chips with a broken GET_FEATURES(TIMINGS)
Raw NAND controllers drivers changes:
- Ams-delta:
* Fixing the error path
* SPDX tag added
* May be compiled with COMPILE_TEST=y
* Conversion to ->exec_op() interface
* Dropping .IOADDR_R/W use
* Use GPIO API for data I/O
- Denali:
* Removing denali_reset_banks()
* Removing ->dev_ready() hook
* Including <linux/bits.h> instead of <linux/bitops.h>
* Changes to comply with the above fixes/cleanup done in the core.
- FSMC:
* Adding an SPDX tag to replace the license text
* Making conversion from chip to fsmc consistent
* Fixing unchecked return value in fsmc_read_page_hwecc
* Changes to comply with the above fixes/cleanup done in the core.
- Marvell:
* Preventing timeouts on a loaded machine (fix)
* Changes to comply with the above fixes/cleanup done in the core.
- OMAP2:
* Pass the parent of pdev to dma_request_chan() (fix)
- R852:
* Use generic DMA API
- sh_flctl:
* Converting to SPDX identifiers
- Sunxi:
* Write pageprog related opcodes to the right register: WCMD_SET (fix)
- Tegra:
* Stop implementing ->select_chip()
- VF610:
* Adding an SPDX tag to replace the license text
* Changes to comply with the above fixes/cleanup done in the core.
- Various trivial/spelling/coding style fixes.
SPI-NAND drivers changes:
- Removing the depreacated mt29f_spinand driver from staging.
- Adding support for:
* Toshiba TC58CVG2S0H
* GigaDevice GD5FxGQ4xA
* Winbond W25N01GV
The opcodes used by the controller when doing batched page prog should
be written in NFC_REG_WCMD_SET not FC_REG_RCMD_SET. Luckily, the
default NFC_REG_WCMD_SET value matches the one we set in the driver
which explains why we didn't notice the problem.
Fixes: 614049a8d9 ("mtd: nand: sunxi: add support for DMA assisted operations")
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
marvell_nfc_wait_op() waits for completion during 'timeout_ms'
milliseconds before throwing an error. While the logic is fine, the
value of 'timeout_ms' is given by the core and actually correspond to
the maximum time the NAND chip will take to complete the
operation. Assuming there is no overhead in the propagation of the
interrupt signal to the the NAND controller (through the Ready/Busy
line), this delay does not take into account the latency of the
operating system. For instance, for a page write, the delay given by
the core is rounded up to 1ms. Hence, when the machine is over loaded,
there is chances that this timeout will be reached.
There are two ways to solve this issue that are not incompatible:
1/ Enlarge the timeout value (if so, how much?).
2/ Check after the waiting method if we did not miss any interrupt
because of the OS latency (an interrupt is still pending). In this
case, we assume the operation exited successfully.
We choose the second approach that is a must in all cases, with the
possibility to also modify the timeout value to be, e.g. at least 1
second in all cases.
Fixes: 02f26ecf8c ("mtd: nand: add reworked Marvell NAND controller driver")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Commit e1e6255c31 ("mtd: rawnand: omap2: convert driver to
nand_scan()") moved part of the init code in the ->attach_chip hook
and at the same time changed the struct device object passed to
dma_request_chan() (&pdev->dev instead of pdev->dev.parent).
Fixes: e1e6255c31 ("mtd: rawnand: omap2: convert driver to nand_scan()")
Reported-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
nand_jedec_detect() should return 1 when the PARAM page parsing
succeeds, otherwise the core considers JEDEC detection failed and falls
back to ID-based detection.
Fixes: 480139d922 ("mtd: rawnand: get rid of the JEDEC parameter page in nand_chip")
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
There is a plan to build the kernel with -Wimplicit-fallthrough and
these places in the code produced warnings. Fix them up.
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
We try to force NAND controller drivers to properly separate the NAND
controller object from the NAND chip one, so let's deprecate the dummy
controller object embedded in nand_chip to encourage them to create
their own instance.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Replace the license text by an SPDX tag.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The dummy controller is kept around to support old drivers. Let's
patch this one and declare our own nand_controller instance.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Mimic what has been done in the core and avoid passing mtd_info object
internally.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
checkpatch reports a bunch of coding style issues. Let's fix them
all in one step.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add an SPDX GPL-2.0 tag and update MODULE_LICENSE() to match the
license text.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The dummy controller is kept around to support old drivers. Let's
patch this one and declare our own nand_controller instance.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
nand_to_fsmc() is used almost everywhere except in
fsmc_setup_data_interface() where nand_get_controller_data() is used
instead. Make that consistent and drop the nand_set_controller_data()
call in the probe path.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The kernel-doc describing struct fsmc_nand_data is not in sync with
the struct itself. Add missing entries and drop invalid ones.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Mimic what has been done in the core and stop passing mtd_info
objects to internal functions.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
In nand_scan_ident(), the controller driver resets every NAND chip.
This is done by sending NAND_CMD_RESET. The Denali IP provides
another way to do the equivalent thing; if a bit is set in the
DEVICE_RESET register, the controller sends the RESET command to
the corresponding device. denali_reset_banks() uses it to reset
all devices beforehand.
This redundant reset sequence was needed to know the actual number
of chips before calling nand_scan_ident(); if DEVICE_RESET fails,
there is no chip in that chip select. Then, denali_reset_banks()
sets denali->max_banks to the number of detected chips.
As commit f486287d23 ("mtd: nand: denali: fix bank reset function
to detect the number of chips") explained, nand_scan_ident() issued
Set Features (0xEF) command to all CS lines, some of which may not be
connected with a chip. Then, the driver would wait for R/B# response,
which never happens.
This problem was solved by commit 107b7d6a7a ("mtd: rawnand: avoid
setting again the timings to mode 0 after a reset"). In the current
code, nand_setup_data_interface() is called from nand_scan_tail(),
which is invoked after the chip detection.
Now, we can really remove the redundant denali_nand_banks() by simply
passing the maximum number of chip selects supported by this IP
(typically 4 or 8) to nand_scan(). Let's leave all the chip detection
process to nand_scan_ident().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The Denali NAND IP has no way to read out the current signal level
of the R/B# pin. Instead, denali_dev_ready() checks if the R/B#
transition has already happened. (The INTR__INT_ACT interrupt is
asserted at the rising edge of the R/B# pin.) It is not a correct
way to implement the ->dev_ready() hook.
In fact, it has a drawback; in the nand_scan_ident phase, the chip
detection iterates over maxchips until it fails to find a homogeneous
chip. For the last loop, nand_reset() fails if no chip is there.
If ->dev_ready hook exists, nand_command(_lp) calls nand_wait_ready()
after NAND_CMD_RESET. However, we know denali_dev_ready() never
returns 1 unless there exists a chip that toggles R/B# in that chip
select. Then, nand_wait_ready() just ends up with wasting 400 msec,
in the end, shows the "timeout while waiting for chip to become ready"
warning.
Let's remove the mis-implemented dev_ready hook, and fallback to
sending the NAND_CMD_STATUS and nand_wait_status_ready(), which
bails out more quickly.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Don't readw()/writew() data directly from/to GPIO port which is under
control of gpio-omap driver, use GPIO consumer API instead.
The driver should now work with any 8-bit bidirectional GPIO port, not
only OMAP.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Data port used by the driver is actually an OMAP MPUIO device, already
under control of gpio-omap driver. For that reason we used to not
request the memory region of the port as that would fail because the
region is already busy. Despite that, we are still accessing the port
by just ioremapping it and performing read/write operations. Moreover,
we are doing that without any proteciton from other users legally
manipulating the port pins over GPIO API.
The plan is to convert the driver to access the port over GPIO consumer
API. Before that happens, already prevent from other users accessing
the port pins by requesting an array of its GPIO descriptors.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
->setup_data_interface() is a controller specific method and should
thus be placed in nand_controller_ops.
In order to make that work with controllers that support keeping
pre-configured timings we need to add a new NAND_KEEP_TIMINGS flag to
inform the core it should skip the timings selection step.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
->exec_op() is a controller method and has nothing to do in the
nand_chip struct. Let's move it to the nand_controller_ops struct and
adjust the core and drivers accordingly.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Now that the CS line to be selected is passed to ->exec_op() and
stored in chip->cur_cs and after patching all drivers implementing
->exec_op() to stop implementing this method, we can deprecate it by
moving it to the nand_legacy structure.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Now that the CS to be selected is passed in nand_operation->cs, we can
get rid of the ->select_chip() implementation and replace it by an
internal function which is called from the chip->exec_op() hook.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Now that the CS to be selected is kept in chip->cur_cs and passed
in nand_operation->cs, we can get rid of the ->select_chip()
implementation and replace it by an internal function which is called
from the chip->exec_op() and chip->ecc.read/write_xxx() hooks.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Now that the CS to be selected is kept in chip->cur_cs and passed
in nand_operation->cs, we can get rid of the ->select_chip()
implementation and replace it by an internal function which is called
from the chip->exec_op() and chip->ecc.read/write_xxx() hooks.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Now that the CS to be selected is kept in chip->cur_cs and passed
in nand_operation->cs, we can get rid of the ->select_chip()
implementation and replace it by an internal function which is called
from the chip->exec_op() and chip->ecc.read/write_xxx() hooks.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Now that the CS line to assert is directly passed through the
nand_operation struct we can replace the fsmc_select_chip()
implementation by an internal fsmc_ce_ctrl() function which is
directly called from fsmc_exec_op()
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
