* 'nouveau/drm-nouveau-next' of ../drm-nouveau-next:
drm/nouveau: fix __nouveau_fence_wait performance
drm/nv40: attempt to reserve just enough vram for all 32 channels
drm/nv50: check for vm traps on every gr irq
drm/nv50: decode vm faults some more
drm/nouveau: add nouveau_enum_find() util function
drm/nouveau: properly handle pushbuffer check failures
drm/nvc0: remove vm hack forcing large/small pages to not share a PDE
Commit 21e86c1c8a ("drm/nouveau: remove
cpu_writers lock") turned on lazy waits. Unfortunately
__nouveau_fence_wait was not optimized for this case and on HZ=100
kernel wasted up to 10 ms per call.
Depending on application, it led to 10-30% FPS regression.
Fix it.
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
This also makes the fact we're giving 512MiB of GART space to all PCIE
boards explicit, although the vast majority (if not all) of them will
now have a ramin_rsvd_vram larger than 2MiB anyway.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Appears to be fixed with commit:
"drm/nv50-nvc0: make sure vma is definitely unmapped when destroying bo"
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
At least on my HP 2540p this is wrong at bootup, fine
at any other time once a lid event has occured. This is due to
_REG vs _INI ordering in the ACPI tables.
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'intel/drm-intel-next' of ../drm-next: (755 commits)
drm/i915: Only wait on a pending flip if we intend to write to the buffer
drm/i915/dp: Sanity check eDP existence
drm/i915: Rebind the buffer if its alignment constraints changes with tiling
drm/i915: Disable GPU semaphores by default
drm/i915: Do not overflow the MMADDR write FIFO
Revert "drm/i915: fix corruptions on i8xx due to relaxed fencing"
drm/i915: Don't save/restore hardware status page address register
drm/i915: don't store the reg value for HWS_PGA
drm/i915: fix memory corruption with GM965 and >4GB RAM
Linux 2.6.38-rc7
Revert "TPM: Long default timeout fix"
drm/i915: Re-enable GPU semaphores for SandyBridge mobile
drm/i915: Replace vblank PM QoS with "Interrupt-Based AGPBUSY#"
Revert "drm/i915: Use PM QoS to prevent C-State starvation of gen3 GPU"
drm/i915: Allow relocation deltas outside of target bo
drm/i915: Silence an innocuous compiler warning for an unused variable
fs/block_dev.c: fix new kernel-doc warning
ACPI: Fix build for CONFIG_NET unset
mm: <asm-generic/pgtable.h> must include <linux/mm_types.h>
x86: Use u32 instead of long to set reset vector back to 0
...
Conflicts:
drivers/gpu/drm/i915/i915_gem.c
Some hardware claims to have both an LVDS panel and an eDP output.
Whilst this may be true in a rare case, more often it is just broken
hardware. If we see an eDP device we know that it must be connected and
so we can confirm its existence with a simple probe.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=34165
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=24822
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Early gen3 and gen2 chipset do not have the relaxed per-surface tiling
constraints of the later chipsets, so we need to check that the GTT
alignment is correct for the new tiling. If it is not, we need to
rebind.
Reported-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Andi Kleen narrowed his GPU hangs on his Sugar Bay (SNB desktop) rev 09
down to the use of GPU semaphores, and we already know that they appear
broken up to Huron River (mobile) rev 08. (I'm optimistic that disabling
GPU semaphores is simply hiding another bug by the latency and
side-effects of the additional device interaction it introduces...)
However, use of semaphores is a massive performance improvement... Only
as long as the system remains stable. Enable at your peril.
Reported-by: Andi Kleen <andi-fd@firstfloor.org>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=33921
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Whilst the GT is powered down (rc6), writes to MMADDR are placed in a
FIFO by the System Agent. This is a limited resource, only 64 entries, of
which 20 are reserved for Display and PCH writes, and so we must take
care not to queue up too many writes. To avoid this, there is counter
which we can poll to ensure there are sufficient free entries in the
fifo.
"Issuing a write to a full FIFO is not supported; at worst it could
result in corruption or a system hang."
Reported-and-Tested-by: Matt Turner <mattst88@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=34056
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This reverts commit c2e0eb1670.
As it turns out, userspace already depends upon being able to enable
tiling on existing bo which it promises to be large enough for its
purposes i.e. it will not access beyond the end of the last full-tile
row.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=35016
Reported-and-tested-by: Kamal Mostafa <kamal@canonical.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We're coming to see a need to have a set of generic capability checks in
the core DRM, in addition to the driver-specific ioctls that already
exist.
This patch defines an ioctl to do as such, but does not yet define any
capabilities.
[airlied: drop the driver callback for now.]
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
hdmi 1.3 raises the max clock from 165 Mhz to 340 Mhz.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
These should be handled by the clear_state setup, but set them
directly as well just to be sure.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Cayman is different enough from evergreen to warrant it's own functions.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Cayman asics have 3 ring buffers:
ring 0 supports both gfx and compute
rings 1 and 2 are compute only
At the moment we only support ring 0.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch sets up the gart in legacy mode. We
probably want to switch to full VM mode at some point.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The MC ucode is no longer loaded by the vbios
tables as on previous asics. It now must be loaded
by the driver.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Cayman is DCE5 display plus a new 4-way shader block.
3D state programming is similar to evergreen.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
It's cleaned before saving and re-initialized after restoring.
So don't need to save/restore it. And also new chip has new address
for hardware status page register, don't write to old address.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
On a Thinkpad x61s, I noticed some memory corruption when
plugging/unplugging the external VGA connection. The symptoms are that
4 bytes at the beginning of a page get overwritten by zeroes.
The address of the corruption varies when rebooting the machine, but
stays constant while it's running (so it's possible to repeatedly write
some data and then corrupt it again by plugging the cable).
Further investigation revealed that the corrupted address is
(dev_priv->status_page_dmah->busaddr & 0xffffffff), ie. the beginning of
the hardware status page of the i965 graphics card, cut to 32 bits.
So it seems that for some memory access, the hardware uses only 32 bit
addressing. If the hardware status page is located >4GB, this
corrupts unrelated memory.
Signed-off-by: Jan Niehusmann <jan@gondor.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
This reverts commit c4ff4b829e.
Ted Ts'o reports:
"TPM is working for me so I can log into employer's network in 2.6.37.
It broke when I tried 2.6.38-rc6, with the following relevant lines
from my dmesg:
[ 11.081627] tpm_tis 00:0b: 1.2 TPM (device-id 0x0, rev-id 78)
[ 25.734114] tpm_tis 00:0b: Operation Timed out
[ 78.040949] tpm_tis 00:0b: Operation Timed out
This caused me to get suspicious, especially since the _other_ TPM
commit in 2.6.38 had already been reverted, so I tried reverting
commit c4ff4b829e: "TPM: Long default timeout fix". With this commit
reverted, my TPM on my Lenovo T410 is once again working."
Requested-and-tested-by: Theodore Ts'o <tytso@mit.edu>
Acked-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This seems to be running stably on my test laptop, so hopefully the
reported hangs where just symptoms of other bugs.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
I stumbled over this magic bit in the gen3 INSTPM:
Bit11 Interrupt-Based AGPBUSY# Enable:
‘0’ = Pending GMCH interrupts will not cause AGPBUSY# assertion.
‘1’ = Pending GMCH interrupts will cause AGPBUSY# assertion and hence
can cause the CPU to exit C3. There is no suppression of cacheable
writes.
Note that in either case in C3 the interrupts are not lost. They will be
forwarded to the ICH when the GMCH is out of C3.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@kernel.org
Using PM latency request turns out to be very fragile and only works for
some systems, depending upon the ACPI implementation. However, I've
stumbled across a promising bit in INSTPM: "Interrupt-Based AGPBUSY#".
This reverts commit b0b544cd37.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Userspace has a legitimate requirement to use a delta that points to
outside of the target bo, and so we need to enable this. (As this is an
abi break, albeit a relaxation of the current restrictions, mark the change
with a new flag.)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
drivers/gpu/drm/i915/i915_irq.c: In function ‘ironlake_irq_postinstall’:
drivers/gpu/drm/i915/i915_irq.c:1618: warning: unused variable ‘pipe’
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
