linux_dsm_epyc7002/Documentation/devicetree/bindings/display/imx/fsl-imx-drm.txt

Freescale i.MX DRM master device
================================

The freescale i.MX DRM master device is a virtual device needed to list all
IPU or other display interface nodes that comprise the graphics subsystem.

Required properties:
- compatible: Should be "fsl,imx-display-subsystem"
- ports: Should contain a list of phandles pointing to display interface ports
  of IPU devices

example:

display-subsystem {
	compatible = "fsl,display-subsystem";
	ports = <&ipu_di0>;
};


Freescale i.MX IPUv3
====================

Required properties:
- compatible: Should be "fsl,<chip>-ipu" where <chip> is one of
  - imx51
  - imx53
  - imx6q
  - imx6qp
- reg: should be register base and length as documented in the
  datasheet
- interrupts: Should contain sync interrupt and error interrupt,
  in this order.
- resets: phandle pointing to the system reset controller and
          reset line index, see reset/fsl,imx-src.txt for details
Additional required properties for fsl,imx6qp-ipu:
- fsl,prg: phandle to prg node associated with this IPU instance
Optional properties:
- port@[0-3]: Port nodes with endpoint definitions as defined in
  Documentation/devicetree/bindings/media/video-interfaces.txt.
  Ports 0 and 1 should correspond to CSI0 and CSI1,
  ports 2 and 3 should correspond to DI0 and DI1, respectively.

example:

ipu: ipu@18000000 {
	#address-cells = <1>;
	#size-cells = <0>;
	compatible = "fsl,imx53-ipu";
	reg = <0x18000000 0x080000000>;
	interrupts = <11 10>;
	resets = <&src 2>;

	ipu_di0: port@2 {
		reg = <2>;

		ipu_di0_disp0: endpoint {
			remote-endpoint = <&display_in>;
		};
	};
};

Freescale i.MX PRE (Prefetch Resolve Engine)
============================================

Required properties:
- compatible: should be "fsl,imx6qp-pre"
- reg: should be register base and length as documented in the
  datasheet
- clocks : phandle to the PRE axi clock input, as described
  in Documentation/devicetree/bindings/clock/clock-bindings.txt and
  Documentation/devicetree/bindings/clock/imx6q-clock.txt.
- clock-names: should be "axi"
- interrupts: should contain the PRE interrupt
- fsl,iram: phandle pointing to the mmio-sram device node, that should be
  used for the PRE SRAM double buffer.

example:

pre@21c8000 {
	compatible = "fsl,imx6qp-pre";
	reg = <0x021c8000 0x1000>;
	interrupts = <GIC_SPI 90 IRQ_TYPE_EDGE_RISING>;
	clocks = <&clks IMX6QDL_CLK_PRE0>;
	clock-names = "axi";
	fsl,iram = <&ocram2>;
};

Freescale i.MX PRG (Prefetch Resolve Gasket)
============================================

Required properties:
- compatible: should be "fsl,imx6qp-prg"
- reg: should be register base and length as documented in the
  datasheet
- clocks : phandles to the PRG ipg and axi clock inputs, as described
  in Documentation/devicetree/bindings/clock/clock-bindings.txt and
  Documentation/devicetree/bindings/clock/imx6q-clock.txt.
- clock-names: should be "ipg" and "axi"
- fsl,pres: phandles to the PRE units attached to this PRG, with the fixed
  PRE as the first entry and the muxable PREs following.

example:

prg@21cc000 {
	compatible = "fsl,imx6qp-prg";
	reg = <0x021cc000 0x1000>;
	clocks = <&clks IMX6QDL_CLK_PRG0_APB>,
		 <&clks IMX6QDL_CLK_PRG0_AXI>;
	clock-names = "ipg", "axi";
	fsl,pres = <&pre1>, <&pre2>, <&pre3>;
};

Parallel display support
========================

Required properties:
- compatible: Should be "fsl,imx-parallel-display"
Optional properties:
- interface_pix_fmt: How this display is connected to the
  display interface. Currently supported types: "rgb24", "rgb565", "bgr666"
  and "lvds666".
- edid: verbatim EDID data block describing attached display.
- ddc: phandle describing the i2c bus handling the display data
  channel
- port@[0-1]: Port nodes with endpoint definitions as defined in
  Documentation/devicetree/bindings/media/video-interfaces.txt.
  Port 0 is the input port connected to the IPU display interface,
  port 1 is the output port connected to a panel.

example:

display@di0 {
	compatible = "fsl,imx-parallel-display";
	edid = [edid-data];
	interface-pix-fmt = "rgb24";

	port@0 {
		reg = <0>;

		display_in: endpoint {
			remote-endpoint = <&ipu_di0_disp0>;
		};
	};

	port@1 {
		reg = <1>;

		display_out: endpoint {
			remote-endpoint = <&panel_in>;
		};
	};
};

panel {
	...

	port {
		panel_in: endpoint {
			remote-endpoint = <&display_out>;
		};
	};
};