Audio was unmuted for HDMI only, need to do so for DP as well.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Flickering is observed on some displays when the number of inserted BTR
frames changes frequently.
[How]
Add in a margin of drift to prevent the inserted number of frames from
jumping around too frequently.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
when programming VID_TIMING, we were using the original VESA timing for DP_VIDM/N.
for YCbCr420 or compressed YCbCr422, using half rate as YCbCr444.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Need to set VID_N_MUL for 4:2:0 cases
[How]
Move setting to enc1_stream_encoder_dp_unblank and
ensure it is also set for non-4:2:0 cases.
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Move out of header to dc_helper.c, in preparation for future
implementations.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To help prevent plane state not being set to the correct default
value if any new properties are added in the future.
[How]
Use the drm helper - which seems to be the common solution among other
DRM drivers.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
we were only checking the return value in one place, thus changing
generic_reg_wait from int to void and reading the register instead of
getting it from generic_reg_wait, when we need the return value.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The plane_reset callback is subclassed but hasn't been updated since
the drm helper got updated to include resetting alpha related state
(state->alpha and state->pixel_blend_mode). The overlay planes
exposed by amdgpu_dm were therefore being rendered as invisible by
default ever since supported was exposed for alpha blending properties
on overlays.
This caused regressions in igt@kms_plane_multiple@atomic-tiling-none
and igt@kms_plane@plane-position-covered-pipe tests.
[How]
Reset the plane state values to their correct values as defined in
the drm helper.
This fixes the IGT test regression.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
To aid recoverable page faults.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We need the first paging queue to handle page faults.
v2: handle any number of SDMA instances gracefully
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Now that we have re-reoute faults to the other IH
ring we can enable retries again.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Incorrect hardcoded assumptions are made regarding luma and chroma
alignment. The actual values set for the DRM framebuffer should be used
when programming the address.
[How]
Respect the given pitch for both luma and chroma planes - it's not like
we can force the alignment to anything else at this point anyway.
Use the FB offset for the chroma planes directly. DRM already
provides this to us so there's no need to calculate it manually.
While we don't actually use the chroma surface size parameters on Raven,
these should have technically been fb->width / 2 and fb->height / 2
since the chroma plane is half size of the luma plane for NV12.
Leave a TODO indicating that those should be set based on the actual
surface format instead since this is only correct for YUV420 formats.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When page table are updated by the CPU, synchronize with the
allocation and initialization of newly allocated page tables.
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If using old kernel config file, CONFIG_ZONE_DEVICE is not selected,
so CONFIG_HMM and CONFIG_HMM_MIRROR is not enabled, the current driver
error message "Failed to register MMU notifier" is not clear. Inform
user with more descriptive message on how to fix the missing kernel
config option.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=109808
Signed-off-by: Philip Yang <Philip.Yang@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
userptr may cross two VMAs if the forked child process (not call exec
after fork) malloc buffer, then free it, and then malloc larger size
buf, kerenl will create new VMA adjacent to old VMA which was cloned
from parent process, some pages of userptr are in the first VMA, the
rest pages are in the second VMA.
HMM expects range only have one VMA, loop over all VMAs in the address
range, create multiple ranges to handle this case. See
is_mergeable_anon_vma in mm/mmap.c for details.
Signed-off-by: Philip Yang <Philip.Yang@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Userptr restore may have concurrent userptr invalidation after
hmm_vma_fault adds the range to the hmm->ranges list, needs call
hmm_vma_range_done to remove the range from hmm->ranges list first,
then reschedule the restore worker. Otherwise hmm_vma_fault will add
same range to the list, this will cause loop in the list because
range->next point to range itself.
Add function untrack_invalid_user_pages to reduce code duplication.
Signed-off-by: Philip Yang <Philip.Yang@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Otherwise we won't be able to cleanly handle page faults.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Make sure that not only the entities are flush, but that
we also wait for the HW to finish all processing.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It's a bug having a dead pointer in the IDR, silently returning
is the worst we can do.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Remove the chash implementation for now since it isn't used any more.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Further testing showed that the idea with the chash doesn't work as expected.
Especially we can't predict when we can remove the entries from the hash again.
So replace the chash with a ring buffer/hash mix where entries in the container
age automatically based on their timestamp.
v2: use ring buffer / hash mix
v3: check the timeout to make sure all entries age
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com> (v2)
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Only process a maximum of 32 IVs before writing back the RPTR. This improves
hw handling when we get close to an overflow in the ring buffer.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
That doesn't seem to have any negative effects.
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Chunming Zhou <david1.zhou@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The doorbells should already be reserved, just enable them.
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Chunming Zhou <david1.zhou@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Disable overflow and enable full drain. This makes fault handling on ring 1
much more reliable since we don't generate back pressure any more.
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Chunming Zhou <david1.zhou@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The buffers should be cleared when possible but we also don't want
buffer creation to fail in the rare case where the ring isn't ready
during the call. This could happen during some suspend/resume sequences.
Cc: Christian König <ckoenig.leichtzumerken@gmail.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The dumb_create API isn't intended for high performance rendering
and it's more useful for userspace (ie. IGT) to have them precleared.
The bonus here is that we also won't needlessly leak whatever was
previously in VRAM, but it also probably wasn't sensitive if it was
going through this API.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
add ras post init function.
Do some initialization after all IP have finished their late init.
Add new member flags which will control the ras work flow.
For now, vbios enable ras for us on boot. That might change in the
future.
So there should be a flag from vbios to tell us if ras is enabled or not
on boot. Looks like there is no such info now.
Other bits of the flags are reserved to control other parts of ras.
Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
add drm info output if ras initialized successfully.
add ras atomfirmware sanity check.
Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
lockdep need a static key.
Previously we set ignore bit to avoid the warning.
Now call sysfs_attr_init to initialize the static key.
Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Reviewed-and-Tested-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Unzero char is accepted by sscanf, so when data is structure but
unexpectedly return error invalid;
Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently, it is not clear how ras is supported. Both software and
hardware can set the supported. That is confusing.
Fix it by adding new member hw_supported.
Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Set ignore bit to satisfy locpdep.
Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Ta is optional, so check if ta firmware is loaded or not.
Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The descriptions of modinfo wrongly show two parameters
for each feature(see below). This patch can fix this
incorrect outputs.
parm: amdgpu_ras_enable:Enable RAS features on the GPU (0 = disable, 1 = enable, -1 = auto (default))
parm: ras_enable:int
parm: amdgpu_ras_mask:Mask of RAS features to enable (default 0xffffffff), only valid when ras_enable == 1
parm: ras_mask:uint
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: xinhui pan <xinhui.pan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
sram ecc capability could be get from firmware_capability field in firmwareinfo table
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
ecc default status (enabled or disabled) could be get from umc_config field in umc_info table
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
add new umc_info structures and new firmware_capability defines
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Suspend will put irq, so resume need get irq back.
And in the same time, skip other ras initialization.
Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
RAS ECC event will combine with GPU reset event, due to
ECC interrupts are caused by uncorrectable error that triggers
GPU reset.
v2: Fix misleading-indentation warning
v3: fix build with CONFIG_HSA_AMD disabled
Signed-off-by: Eric Huang <JinhuiEric.Huang@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It is to collaborate with HSA_CAPABILITY in libhsakmt.
v2: squash in NULL pointer check
Signed-off-by: Eric Huang <JinhuiEric.Huang@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently, the debugfs control node can't parse bash-like commands.
Now add such support for any tester that uses scripts.
v2: squash in fixes for input validation
Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
gpu reset is not stable on vega20 A1.
Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add a query for userspace to check which RAS features
are enabled.
v2: squash in warning fix
Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add AMDGPU_CTX_QUERY2_FLAGS_RAS_CE/UE which indicate if any error happened
between previous query and this query.
Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
