Add GPIO key to check presence of PCIE E2B.
Signed-off-by: Lei YU <mine260309@gmail.com>
Acked-by: Xo Wang <xow@google.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
There is a random number generator that updates a register in the SCU
every second. This is compatible with the timeriomem rng driver in the
kernel.
From the timeriomem_rng bindings:
quality: estimated number of bits of true entropy per 1024 bits read
from the rng. Defaults to zero which causes the kernel's default
quality to be used instead. Note that the default quality is usually
zero which disables using this rng to automatically fill the kernel's
entropy pool.
As to the recommended value for us to use:
Rick Altherr <raltherr@google.com> wrote:
> Quality is #bit of entropy per 1000 bits read. 100 is a
> conservative value that was suggested by those in the know.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Pull networking fixes from David Miller:
1) The sockmap code has to free socket memory on close if there is
corked data, from John Fastabend.
2) Tunnel names coming from userspace need to be length validated. From
Eric Dumazet.
3) arp_filter() has to take VRFs properly into account, from Miguel
Fadon Perlines.
4) Fix oops in error path of tcf_bpf_init(), from Davide Caratti.
5) Missing idr_remove() in u32_delete_key(), from Cong Wang.
6) More syzbot stuff. Several use of uninitialized value fixes all
over, from Eric Dumazet.
7) Do not leak kernel memory to userspace in sctp, also from Eric
Dumazet.
8) Discard frames from unused ports in DSA, from Andrew Lunn.
9) Fix DMA mapping and reset/failover problems in ibmvnic, from Thomas
Falcon.
10) Do not access dp83640 PHY registers prematurely after reset, from
Esben Haabendal.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (46 commits)
vhost-net: set packet weight of tx polling to 2 * vq size
net: thunderx: rework mac addresses list to u64 array
inetpeer: fix uninit-value in inet_getpeer
dp83640: Ensure against premature access to PHY registers after reset
devlink: convert occ_get op to separate registration
ARM: dts: ls1021a: Specify TBIPA register address
net/fsl_pq_mdio: Allow explicit speficition of TBIPA address
ibmvnic: Do not reset CRQ for Mobility driver resets
ibmvnic: Fix failover case for non-redundant configuration
ibmvnic: Fix reset scheduler error handling
ibmvnic: Zero used TX descriptor counter on reset
ibmvnic: Fix DMA mapping mistakes
tipc: use the right skb in tipc_sk_fill_sock_diag()
sctp: sctp_sockaddr_af must check minimal addr length for AF_INET6
net: dsa: Discard frames from unused ports
sctp: do not leak kernel memory to user space
soreuseport: initialise timewait reuseport field
ipv4: fix uninit-value in ip_route_output_key_hash_rcu()
dccp: initialize ireq->ir_mark
net: fix uninit-value in __hw_addr_add_ex()
...
Pull ARM updates from Russell King:
"A number of core ARM changes:
- Refactoring linker script by Nicolas Pitre
- Enable source fortification
- Add support for Cortex R8"
* 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: decompressor: fix warning introduced in fortify patch
ARM: 8751/1: Add support for Cortex-R8 processor
ARM: 8749/1: Kconfig: Add ARCH_HAS_FORTIFY_SOURCE
ARM: simplify and fix linker script for TCM
ARM: linker script: factor out TCM bits
ARM: linker script: factor out vectors and stubs
ARM: linker script: factor out unwinding table sections
ARM: linker script: factor out stuff for the .text section
ARM: linker script: factor out stuff for the DISCARD section
ARM: linker script: factor out some common definitions between XIP and non-XIP
The current (mildly evil) fsl_pq_mdio code uses an undocumented shadow of
the TBIPA register on LS1021A, which happens to be read-only.
Changing TBI PHY address therefore does not work on LS1021A.
The real (and documented) address of the TBIPA registere lies in the eTSEC
block and not in MDIO/MII, which is read/write, so using that fixes
the problem.
Signed-off-by: Esben Haabendal <eha@deif.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge updates from Andrew Morton:
- a few misc things
- ocfs2 updates
- the v9fs maintainers have been missing for a long time. I've taken
over v9fs patch slinging.
- most of MM
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (116 commits)
mm,oom_reaper: check for MMF_OOM_SKIP before complaining
mm/ksm: fix interaction with THP
mm/memblock.c: cast constant ULLONG_MAX to phys_addr_t
headers: untangle kmemleak.h from mm.h
include/linux/mmdebug.h: make VM_WARN* non-rvals
mm/page_isolation.c: make start_isolate_page_range() fail if already isolated
mm: change return type to vm_fault_t
mm, oom: remove 3% bonus for CAP_SYS_ADMIN processes
mm, page_alloc: wakeup kcompactd even if kswapd cannot free more memory
kernel/fork.c: detect early free of a live mm
mm: make counting of list_lru_one::nr_items lockless
mm/swap_state.c: make bool enable_vma_readahead and swap_vma_readahead() static
block_invalidatepage(): only release page if the full page was invalidated
mm: kernel-doc: add missing parameter descriptions
mm/swap.c: remove @cold parameter description for release_pages()
mm/nommu: remove description of alloc_vm_area
zram: drop max_zpage_size and use zs_huge_class_size()
zsmalloc: introduce zs_huge_class_size()
mm: fix races between swapoff and flush dcache
fs/direct-io.c: minor cleanups in do_blockdev_direct_IO
...
Calling __stack_chk_guard_setup() in decompress_kernel() is too late
that stack checking always fails for decompress_kernel() itself. So
remove __stack_chk_guard_setup() and initialize __stack_chk_guard before
we call decompress_kernel().
Original code comes from ARM but also used for MIPS and SH, so fix them
together. If without this fix, compressed booting of these archs will
fail because stack checking is enabled by default (>=4.16).
Link: http://lkml.kernel.org/r/1522226933-29317-1-git-send-email-chenhc@lemote.com
Fixes: 8779657d29 ("stackprotector: Introduce CONFIG_CC_STACKPROTECTOR_STRONG")
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Acked-by: James Hogan <jhogan@kernel.org>
Acked-by: Kees Cook <keescook@chromium.org>
Acked-by: Rich Felker <dalias@libc.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This release brings up a new platform based on the old ARM9 core: the
Nuvoton NPCM is used as a baseboard management controller, competing
with the better known ASpeed AST2xx series.
Another important change is the addition of ARMv7-A based chips
in mach-stm32. The older parts in this platform are ARMv7-M based
microcontrollers, now they are expanding to general-purpose workloads.
The other changes are the usual defconfig updates to enable additional
drivers, lesser bugfixes. The largest updates as often are the ongoing
OMAP cleanups, but we also have a number of changes for the older
PXA and davinci platforms this time.
For the Renesas shmobile/r-car platform, some new infrastructure
is needed to make the watchdog work correctly.
Supporting Multiprocessing on Allwinner A80 required a significant
amount of new code, but is not doing anything unexpected.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=HD9V
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Arnd Bergmann:
"This release brings up a new platform based on the old ARM9 core: the
Nuvoton NPCM is used as a baseboard management controller, competing
with the better known ASpeed AST2xx series.
Another important change is the addition of ARMv7-A based chips in
mach-stm32. The older parts in this platform are ARMv7-M based
microcontrollers, now they are expanding to general-purpose workloads.
The other changes are the usual defconfig updates to enable additional
drivers, lesser bugfixes. The largest updates as often are the ongoing
OMAP cleanups, but we also have a number of changes for the older PXA
and davinci platforms this time.
For the Renesas shmobile/r-car platform, some new infrastructure is
needed to make the watchdog work correctly.
Supporting Multiprocessing on Allwinner A80 required a significant
amount of new code, but is not doing anything unexpected"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (179 commits)
arm: npcm: modify configuration for the NPCM7xx BMC.
MAINTAINERS: update entry for ARM/berlin
ARM: omap2: fix am43xx build without L2X0
ARM: davinci: da8xx: simplify CFGCHIP regmap_config
ARM: davinci: da8xx: fix oops in USB PHY driver due to stack allocated platform_data
ARM: multi_v7_defconfig: add NXP FlexCAN IP support
ARM: multi_v7_defconfig: enable thermal driver for i.MX devices
ARM: multi_v7_defconfig: add RN5T618 PMIC family support
ARM: multi_v7_defconfig: add NXP graphics drivers
ARM: multi_v7_defconfig: add GPMI NAND controller support
ARM: multi_v7_defconfig: add OCOTP driver for NXP SoCs
ARM: multi_v7_defconfig: configure I2C driver built-in
arm64: defconfig: add CONFIG_UNIPHIER_THERMAL and CONFIG_SNI_AVE
ARM: imx: fix imx6sll-only build
ARM: imx: select ARM_CPU_SUSPEND for CPU_IDLE as well
ARM: mxs_defconfig: Re-sync defconfig
ARM: imx_v4_v5_defconfig: Use the generic fsl-asoc-card driver
ARM: imx_v4_v5_defconfig: Re-sync defconfig
arm64: defconfig: enable stmmac ethernet to defconfig
ARM: EXYNOS: Simplify code in coupled CPU idle hot path
...
This is the usual set of changes for device trees, with over 700
non-merged changesets. There is an ongoing set of dtc warning fixes and
the usual bugfixes, cleanups and added device support.
The most interesting bit as usual is support for new machines listed
below:
- The Allwinner H6 makes its debut with the Pine-H64 board, and we get
two new machines based on its older siblings: the H5 based OrangePi
Zero+ and the A64 based Teres-I Laptop from Olimex. On the 32-bit side,
we add The Olimex som204 based on Allwinner A20, and the Banana Pi M2
Zero development board (based on H2).
- NVIDIA adds support for Tegra194 aka "Xavier", plus their p2972
development board and p2888 CPU module.
- The Nuvoton npcm750 is a BMC that was newly added, for now we only
support running on the evaluation board.
- STmicroelectronics stm32 gains support for the stm32mp157c and two
evaluation boards.
- The Toradex Colibri board family grows a few members based on the
i.MX6ULL variant.
- The Advantec DMS-BA16 is a Qseven module using the NXP i.MX6
family of chips.
- The Phytec phyBOARD Mira is a family of industrial boards based on
i.MX6. For now, four models get added.
- TI am335x based PDU-001 is an industrial embedded machine used for
traffic monitoring
- The Aspeed platform now supports running on the BMC on the Qualcomm
Centriq 2400 server
- Samsung Exynos4 based Galaxy S3 is a family of mobile phones Qualcomm
msm8974 based Galaxy S5 is a rather different phone made by the same
company.
- The Xilinx Zynq and ZynqMP platforms now gained a lot of dts file
for the various boards made by Xilinx themselves, as well as the
Digilent Zybo Z7.
- The ARM Versatile family now supports the "IB2" interface board.
- The Renesas H2 based "Stout" and the H3 based Salvator-X are more
evaluation boards named after a kind of beer, as most of them are.
The r8a77980 (V3H) based "Condor" apparently doesn't follow that
tradition. ;-)
- ROC-RK3328-CC is a simple developement board from the Libre Computer
Project, based on the Rockchips RK3328 SoC
- Haiku is another development board plus Qseven module based on Rockchips
RK3368 and made by Theobroma Systems.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=7rHo
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree updates from Arnd Bergmann:
"This is the usual set of changes for device trees, with over 700
non-merged changesets. There is an ongoing set of dtc warning fixes
and the usual bugfixes, cleanups and added device support.
The most interesting bit as usual is support for new machines listed
below:
- The Allwinner H6 makes its debut with the Pine-H64 board, and we
get two new machines based on its older siblings: the H5 based
OrangePi Zero+ and the A64 based Teres-I Laptop from Olimex. On the
32-bit side, we add The Olimex som204 based on Allwinner A20, and
the Banana Pi M2 Zero development board (based on H2).
- NVIDIA adds support for Tegra194 aka "Xavier", plus their p2972
development board and p2888 CPU module.
- The Nuvoton npcm750 is a BMC that was newly added, for now we only
support running on the evaluation board.
- STmicroelectronics stm32 gains support for the stm32mp157c and two
evaluation boards.
- The Toradex Colibri board family grows a few members based on the
i.MX6ULL variant.
- The Advantec DMS-BA16 is a Qseven module using the NXP i.MX6 family
of chips.
- The Phytec phyBOARD Mira is a family of industrial boards based on
i.MX6. For now, four models get added.
- TI am335x based PDU-001 is an industrial embedded machine used for
traffic monitoring
- The Aspeed platform now supports running on the BMC on the Qualcomm
Centriq 2400 server
- Samsung Exynos4 based Galaxy S3 is a family of mobile phones
Qualcomm msm8974 based Galaxy S5 is a rather different phone made
by the same company.
- The Xilinx Zynq and ZynqMP platforms now gained a lot of dts file
for the various boards made by Xilinx themselves, as well as the
Digilent Zybo Z7.
- The ARM Versatile family now supports the "IB2" interface board.
- The Renesas H2 based "Stout" and the H3 based Salvator-X are more
evaluation boards named after a kind of beer, as most of them are.
The r8a77980 (V3H) based "Condor" apparently doesn't follow that
tradition. ;-)
- ROC-RK3328-CC is a simple developement board from the Libre
Computer Project, based on the Rockchips RK3328 SoC
- Haiku is another development board plus Qseven module based on
Rockchips RK3368 and made by Theobroma Systems"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (701 commits)
arm: dts: modify Nuvoton NPCM7xx device tree structure
arm: dts: modify Makefile NPCM750 configuration name
arm: dts: modify clock binding in NPCM750 device tree
arm: dts: modify timer register size in NPCM750 device tree
arm: dts: modify UART compatible name in NPCM750 device tree
arm: dts: add watchdog device to NPCM750 device tree
arm64: dts: uniphier: add ethernet node for PXs3
ARM: dts: uniphier: add pinctrl groups of ethernet for second instance
arm: dts: kirkwood*.dts: use SPDX-License-Identifier for board using GPL-2.0+
arm: dts: kirkwood*.dts: use SPDX-License-Identifier for boards using GPL-2.0+/MIT
arm: dts: kirkwood*.dts: use SPDX-License-Identifier for boards using GPL-2.0
arm: dts: armada-385-turris-omnia: use SPDX-License-Identifier
arm: dts: armada-385-db-ap: use SPDX-License-Identifier
arm: dts: armada-388-rd: use SPDX-License-Identifier
arm: dts: armada-xp-db-xc3-24g4xg: use SPDX-License-Identifier
arm: dts: armada-xp-db-dxbc2: use SPDX-License-Identifier
arm: dts: armada-370-db: use SPDX-License-Identifier
arm: dts: armada-*.dts: use SPDX-License-Identifier for most of the Armada based board
arm: dts: armada-xp-98dx: use SPDX-License-Identifier for prestara 98d SoCs
arm: dts: armada-*.dtsi: use SPDX-License-Identifier for most of the Armada SoCs
...
- Sync dtc to upstream version v1.4.6-9-gaadd0b65c987. This adds a bunch
more warnings (hidden behind W=1).
- Build dtc lexer and parser files instead of using shipped versions.
- Rework overlay apply API to take an FDT as input and apply overlays in
a single step.
- Add a phandle lookup cache. This improves boot time by hundreds of
msec on systems with large DT.
- Add trivial mcp4017/18/19 potentiometers bindings.
- Remove VLA stack usage in DT code.
-----BEGIN PGP SIGNATURE-----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=ZWpa
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree updates from Rob Herring:
- Sync dtc to upstream version v1.4.6-9-gaadd0b65c987. This adds a
bunch more warnings (hidden behind W=1).
- Build dtc lexer and parser files instead of using shipped versions.
- Rework overlay apply API to take an FDT as input and apply overlays
in a single step.
- Add a phandle lookup cache. This improves boot time by hundreds of
msec on systems with large DT.
- Add trivial mcp4017/18/19 potentiometers bindings.
- Remove VLA stack usage in DT code.
* tag 'devicetree-for-4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (26 commits)
of: unittest: fix an error code in of_unittest_apply_overlay()
of: unittest: move misplaced function declaration
of: unittest: Remove VLA stack usage
of: overlay: Fix forgotten reference to of_overlay_apply()
of: Documentation: Fix forgotten reference to of_overlay_apply()
of: unittest: local return value variable related cleanups
of: unittest: remove unneeded local return value variables
dt-bindings: trivial: add various mcp4017/18/19 potentiometers
of: unittest: fix an error test in of_unittest_overlay_8()
of: cache phandle nodes to reduce cost of of_find_node_by_phandle()
dt-bindings: rockchip-dw-mshc: use consistent clock names
MAINTAINERS: Add linux/of_*.h headers to appropriate subsystems
scripts: turn off some new dtc warnings by default
scripts/dtc: Update to upstream version v1.4.6-9-gaadd0b65c987
scripts/dtc: generate lexer and parser during build instead of shipping
powerpc: boot: add strrchr function
of: overlay: do not include path in full_name of added nodes
of: unittest: clean up changeset test
arm64/efi: Make strrchr() available to the EFI namespace
ARM: boot: add strrchr function
...
Commit ee333554fe ("ARM: 8749/1: Kconfig: Add ARCH_HAS_FORTIFY_SOURCE")
introduced a new warning:
arch/arm/boot/compressed/misc.c: In function 'fortify_panic':
arch/arm/boot/compressed/misc.c:167:1: error: 'noreturn' function does return [-Werror]
The simple solution would be to make 'error' a noreturn function, but
this causes a prototype mismatch as the function is prototyped in
several .c files. So, move the function prototype to a new header.
There are also a couple of variables that are also declared in several
locations. Clean this up while we are here.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Modify Nuvoton NPCM7xx device tree structure by adding
nuvoton common nNPCM7xx device tree structure that
include all common modules.
Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Modify clock binding in a common device tree for all Nuvoton
NPCM750 BMCs.
Modify NPCM750 modules clock numbers accourding the new
clock driver.
Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Modify timer register size in a common device tree for all Nuvoton
NPCM750 BMCs.
Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Modify UART compatible name in a common device tree for all Nuvoton
NPCM750 BMCs.
Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add watchdog device node to a common device tree for all Nuvoton
NPCM750 BMCs and a board specific device tree for the NPCM750 (Poleg)
evaluation board.
Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Here is the big set of Staging/IIO driver patches for 4.17-rc1.
It is a lot, over 500 changes, but not huge by previous kernel release
standards. We deleted more lines than we added again (27k added vs. 91k
remvoed), thanks to finally being able to delete the IRDA drivers and
networking code.
We also deleted the ccree crypto driver, but that's coming back in
through the crypto tree to you, in a much cleaned-up form.
Added this round is at lot of "mt7621" device support, which is for an
embedded device that Neil Brown cares about, and of course a handful of
new IIO drivers as well.
And finally, the fsl-mc core code moved out of the staging tree to the
"real" part of the kernel, which is nice to see happen as well.
Full details are in the shortlog, which has all of the tiny cleanup
patches described.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWsSnAA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yn60ACgxKvU/5XBP14hBkBpAcD0Q43OHe0AniEti65M
Kw03GWK3NNM3pzk49BjZ
=sj3K
-----END PGP SIGNATURE-----
Merge tag 'staging-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO updates from Greg KH:
"Here is the big set of Staging/IIO driver patches for 4.17-rc1.
It is a lot, over 500 changes, but not huge by previous kernel release
standards. We deleted more lines than we added again (27k added vs.
91k remvoed), thanks to finally being able to delete the IRDA drivers
and networking code.
We also deleted the ccree crypto driver, but that's coming back in
through the crypto tree to you, in a much cleaned-up form.
Added this round is at lot of "mt7621" device support, which is for an
embedded device that Neil Brown cares about, and of course a handful
of new IIO drivers as well.
And finally, the fsl-mc core code moved out of the staging tree to the
"real" part of the kernel, which is nice to see happen as well.
Full details are in the shortlog, which has all of the tiny cleanup
patches described.
All of these have been in linux-next for a while with no reported
issues"
* tag 'staging-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (579 commits)
staging: rtl8723bs: Remove yield call, replace with cond_resched()
staging: rtl8723bs: Replace yield() call with cond_resched()
staging: rtl8723bs: Remove unecessary newlines from 'odm.h'.
staging: rtl8723bs: Rework 'struct _ODM_Phy_Status_Info_' coding style.
staging: rtl8723bs: Rework 'struct _ODM_Per_Pkt_Info_' coding style.
staging: rtl8723bs: Replace NULL pointer comparison with '!'.
staging: rtl8723bs: Factor out rtl8723bs_recv_tasklet() sections.
staging: rtl8723bs: Fix function signature that goes over 80 characters.
staging: rtl8723bs: Fix lines too long in update_recvframe_attrib().
staging: rtl8723bs: Remove unnecessary blank lines in 'rtl8723bs_recv.c'.
staging: rtl8723bs: Change camel case to snake case in 'rtl8723bs_recv.c'.
staging: rtl8723bs: Add missing braces in else statement.
staging: rtl8723bs: Add spaces around ternary operators.
staging: rtl8723bs: Fix lines with trailing open parentheses.
staging: rtl8723bs: Remove unnecessary length #define's.
staging: rtl8723bs: Fix IEEE80211 authentication algorithm constants.
staging: rtl8723bs: Fix alignment in rtw_wx_set_auth().
staging: rtl8723bs: Remove braces from single statement conditionals.
staging: rtl8723bs: Remove unecessary braces from switch statement.
staging: rtl8723bs: Fix newlines in rtw_wx_set_auth().
...
Here is the big set of tty and serial driver patches for 4.17-rc1
Not all that big really, most are just small fixes and additions to
existing drivers. There's a bunch of work on the imx serial driver
recently for some reason, and a new embedded serial driver added as
well.
Full details are in the shortlog.
All of these have been in the linux-next tree for a while with no
reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWsSn+w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynb6wCdEf5dAUrSB37ptZY78n4kc6nI6NAAniDO+rjL
ppZZp7QTIB/bnPfW8cOH
=+tfY
-----END PGP SIGNATURE-----
Merge tag 'tty-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here is the big set of tty and serial driver patches for 4.17-rc1
Not all that big really, most are just small fixes and additions to
existing drivers. There's a bunch of work on the imx serial driver
recently for some reason, and a new embedded serial driver added as
well.
Full details are in the shortlog.
All of these have been in the linux-next tree for a while with no
reported issues"
* tag 'tty-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (66 commits)
serial: expose buf_overrun count through proc interface
serial: mvebu-uart: fix tx lost characters
tty: serial: msm_geni_serial: Fix return value check in qcom_geni_serial_probe()
tty: serial: msm_geni_serial: Add serial driver support for GENI based QUP
8250-men-mcb: add support for 16z025 and 16z057
powerpc: Mark the variable earlycon_acpi_spcr_enable maybe_unused
serial: stm32: fix initialization of RS485 mode
ARM: dts: STi: Remove "console=ttyASN" from bootargs for STi boards
vt: change SGR 21 to follow the standards
serdev: Fix typo in serdev_device_alloc
ARM: dts: STi: Fix aliases property name for STi boards
tty: st-asc: Update tty alias
serial: stm32: add support for RS485 hardware control mode
dt-bindings: serial: stm32: add RS485 optional properties
selftests: add devpts selftests
devpts: comment devpts_mntget()
devpts: resolve devpts bind-mounts
devpts: hoist out check for DEVPTS_SUPER_MAGIC
serial: 8250: Add Nuvoton NPCM UART
serial: mxs-auart: disable clks of Alphascale ASM9260
...
- add a shell script to get Clang version
- improve portability of build scripts
- drop always-enabled CONFIG_THIN_ARCHIVE and remove unused code
- rename built-in.o which is now thin archive to built-in.a
- process clean/build targets one by one to get along with -j option
- simplify ld-option
- improve building with CONFIG_TRIM_UNUSED_KSYMS
- define KBUILD_MODNAME even for objects shared among multiple modules
- avoid linking multiple instances of same objects from composite objects
- move <linux/compiler_types.h> to c_flags to include it only for C files
- clean-up various Makefiles
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=N5BL
-----END PGP SIGNATURE-----
Merge tag 'kbuild-v4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild updates from Masahiro Yamada:
- add a shell script to get Clang version
- improve portability of build scripts
- drop always-enabled CONFIG_THIN_ARCHIVE and remove unused code
- rename built-in.o which is now thin archive to built-in.a
- process clean/build targets one by one to get along with -j option
- simplify ld-option
- improve building with CONFIG_TRIM_UNUSED_KSYMS
- define KBUILD_MODNAME even for objects shared among multiple modules
- avoid linking multiple instances of same objects from composite
objects
- move <linux/compiler_types.h> to c_flags to include it only for C
files
- clean-up various Makefiles
* tag 'kbuild-v4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (29 commits)
kbuild: get <linux/compiler_types.h> out of <linux/kconfig.h>
kbuild: clean up link rule of composite modules
kbuild: clean up archive rule of built-in.a
kbuild: remove partial section mismatch detection for built-in.a
net: liquidio: clean up Makefile for simpler composite object handling
lib: zstd: clean up Makefile for simpler composite object handling
kbuild: link $(real-obj-y) instead of $(obj-y) into built-in.a
kbuild: rename real-objs-y/m to real-obj-y/m
kbuild: move modname and modname-multi close to modname_flags
kbuild: simplify modname calculation
kbuild: fix modname for composite modules
kbuild: define KBUILD_MODNAME even if multiple modules share objects
kbuild: remove unnecessary $(subst $(obj)/, , ...) in modname-multi
kbuild: Use ls(1) instead of stat(1) to obtain file size
kbuild: link vmlinux only once for CONFIG_TRIM_UNUSED_KSYMS
kbuild: move include/config/ksym/* to include/ksym/*
kbuild: move CONFIG_TRIM_UNUSED_KSYMS code unneeded for external module
kbuild: restore autoksyms.h touch to the top Makefile
kbuild: move 'scripts' target below
kbuild: remove wrong 'touch' in adjust_autoksyms.sh
...
Pull networking updates from David Miller:
1) Support offloading wireless authentication to userspace via
NL80211_CMD_EXTERNAL_AUTH, from Srinivas Dasari.
2) A lot of work on network namespace setup/teardown from Kirill Tkhai.
Setup and cleanup of namespaces now all run asynchronously and thus
performance is significantly increased.
3) Add rx/tx timestamping support to mv88e6xxx driver, from Brandon
Streiff.
4) Support zerocopy on RDS sockets, from Sowmini Varadhan.
5) Use denser instruction encoding in x86 eBPF JIT, from Daniel
Borkmann.
6) Support hw offload of vlan filtering in mvpp2 dreiver, from Maxime
Chevallier.
7) Support grafting of child qdiscs in mlxsw driver, from Nogah
Frankel.
8) Add packet forwarding tests to selftests, from Ido Schimmel.
9) Deal with sub-optimal GSO packets better in BBR congestion control,
from Eric Dumazet.
10) Support 5-tuple hashing in ipv6 multipath routing, from David Ahern.
11) Add path MTU tests to selftests, from Stefano Brivio.
12) Various bits of IPSEC offloading support for mlx5, from Aviad
Yehezkel, Yossi Kuperman, and Saeed Mahameed.
13) Support RSS spreading on ntuple filters in SFC driver, from Edward
Cree.
14) Lots of sockmap work from John Fastabend. Applications can use eBPF
to filter sendmsg and sendpage operations.
15) In-kernel receive TLS support, from Dave Watson.
16) Add XDP support to ixgbevf, this is significant because it should
allow optimized XDP usage in various cloud environments. From Tony
Nguyen.
17) Add new Intel E800 series "ice" ethernet driver, from Anirudh
Venkataramanan et al.
18) IP fragmentation match offload support in nfp driver, from Pieter
Jansen van Vuuren.
19) Support XDP redirect in i40e driver, from Björn Töpel.
20) Add BPF_RAW_TRACEPOINT program type for accessing the arguments of
tracepoints in their raw form, from Alexei Starovoitov.
21) Lots of striding RQ improvements to mlx5 driver with many
performance improvements, from Tariq Toukan.
22) Use rhashtable for inet frag reassembly, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1678 commits)
net: mvneta: improve suspend/resume
net: mvneta: split rxq/txq init and txq deinit into SW and HW parts
ipv6: frags: fix /proc/sys/net/ipv6/ip6frag_low_thresh
net: bgmac: Fix endian access in bgmac_dma_tx_ring_free()
net: bgmac: Correctly annotate register space
route: check sysctl_fib_multipath_use_neigh earlier than hash
fix typo in command value in drivers/net/phy/mdio-bitbang.
sky2: Increase D3 delay to sky2 stops working after suspend
net/mlx5e: Set EQE based as default TX interrupt moderation mode
ibmvnic: Disable irqs before exiting reset from closed state
net: sched: do not emit messages while holding spinlock
vlan: also check phy_driver ts_info for vlan's real device
Bluetooth: Mark expected switch fall-throughs
Bluetooth: Set HCI_QUIRK_SIMULTANEOUS_DISCOVERY for BTUSB_QCA_ROME
Bluetooth: btrsi: remove unused including <linux/version.h>
Bluetooth: hci_bcm: Remove DMI quirk for the MINIX Z83-4
sh_eth: kill useless check in __sh_eth_get_regs()
sh_eth: add sh_eth_cpu_data::no_xdfar flag
ipv6: factorize sk_wmem_alloc updates done by __ip6_append_data()
ipv4: factorize sk_wmem_alloc updates done by __ip_append_data()
...
- Export host capabilities through debugfs
- Export card RCA register via sysfs
- Improve card initializing sequence while enabling 4-bit bus
- Export a function to enable/disable wakeup for card detect IRQ
MMC host:
- dw_mmc: Add support for new hi3798cv200 variant
- dw_mmc: Remove support for some deprecated DT properties
- mediatek: Add support for new variant used on MT7622 SoC
- sdhci: Improve wakeup support for SDIO IRQs
- sdhci: Improve wakeup support for card detect IRQs
- sdhci-omap: Add tuning support
- sdhci_omap: Add UHS-I mode support
- sunxi: Prepare for runtime PM support via a few re-factorings
- tmio: deprecate "toshiba,mmc-wrprotect-disable" DT property
- tmio/renesas_sdhi: Consolidate code supporting write protect
- tmio: Improve DMA vs PIO handling
- tmio: Add support for IP-builtin card detection logic
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJaw0MuAAoJEP4mhCVzWIwpW78P/2N2qPt21OfvnIbSexY1nyPd
5+rjScgy+oTUnNxITA9LOnM4P6Wg/9PgvhjUdNdHzd5ZaXIchw372+Xu6hZHdujI
vBfnpsI/xtyL1TQ6nvJc9b+Sp4W4LL2MlCqxi+btAKLvTAU3NNm7uJRRP6xRNDd5
8wcsCoIN4C3k5hmh5++DDLCfuzpwmbC1cEbGtL/QEV9xeCY5+fJq4Qpq14L2TJ0g
LeDls3X4HAJa3SsgSGOdNr8rttKUSS+j7i1XsShHMyq89DD21PJ8fvMhdzlXJub9
A4PatcOXALS/Xd2YVjeLHrRRlTitssD+Sllt46NsB4eJJOO+DempecY+i0WoW60y
p9IUSSX86yokGoyweiL2GI0Ja1Bg8xgdzTGVbfZ6w6UKHjQAcItnojyMghDM5+zt
VjDIU59rzm+BEDqcktsbGgLPjOZ0ZWgJPPp2NPkechxsojvCJ9Smm6yPjzaUnZ60
U9PxsYbs4NB+nE9iKDioyA1ABP0N+BloUkTf/cVHdPBBPMmOyI7jYEDS7mqollZU
bQCFx+BqcQMbnvI/TZxNDTr4HsiyiXJa0GTCB77sge8tZdcUTjUsWyhc+BYpIqgA
68/dlwTcawSXDliup5XxtYcAjGugtHbPnS/39uBXvscqWVej1WI5RTyzKdC/hnos
BP5uz0K1Wic1Dl+jqlWc
=2Pd6
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Export host capabilities through debugfs
- Export card RCA register via sysfs
- Improve card initializing sequence while enabling 4-bit bus
- Export a function to enable/disable wakeup for card detect IRQ
MMC host:
- dw_mmc: Add support for new hi3798cv200 variant
- dw_mmc: Remove support for some deprecated DT properties
- mediatek: Add support for new variant used on MT7622 SoC
- sdhci: Improve wakeup support for SDIO IRQs
- sdhci: Improve wakeup support for card detect IRQs
- sdhci-omap: Add tuning support
- sdhci_omap: Add UHS-I mode support
- sunxi: Prepare for runtime PM support via a few re-factorings
- tmio: deprecate "toshiba,mmc-wrprotect-disable" DT property
- tmio/renesas_sdhi: Consolidate code supporting write protect
- tmio: Improve DMA vs PIO handling
- tmio: Add support for IP-builtin card detection logic"
* tag 'mmc-v4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (55 commits)
mmc: renesas_sdhi: replace EXT_ACC with HOST_MODE
mmc: update sdio_claim_irq documentation
mmc: Export host capabilities to debugfs.
mmc: core: Disable HPI for certain Micron (Numonyx) eMMC cards
mmc: block: fix updating ext_csd caches on ioctl call
mmc: sunxi: Set our device drvdata earlier
mmc: sunxi: Move the reset deassertion before enabling the clocks
mmc: sunxi: Move resources management to separate functions
mmc: dw_mmc: add support for hi3798cv200 specific extensions of dw-mshc
dt-bindings: mmc: add bindings for hi3798cv200-dw-mshc
mmc: core: Export card RCA register via sysfs
mmc: renesas_sdhi: fix WP detection
mmc: core: Use memdup_user() rather than duplicating its implementation
mmc: dw_mmc-rockchip: correct property names in debug
mmc: sd: Remove redundant err assignment from mmc_read_switch
mmc: sdio: Check the return value of sdio_enable_4bit_bus
mmc: core: Don't try UHS-I mode if 4-bit mode isn't supported
arm64: dts: hi3660: remove 'num-slots' property for dwmmc
ARM: dts: lpc18xx: remove 'num-slots' property for dwmmc
arm64: dts: stratix10: remove 'num-slots' property for dwmmc
...
* Microsemi Ocelot reset support
* Spreadtrum SC27xx reset support
* generic gpio charger: lot's of cleanups
* axp20x fuel gauge: add AXP813 support
* misc. fixes
-----BEGIN PGP SIGNATURE-----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=VY8H
-----END PGP SIGNATURE-----
Merge tag 'for-v4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply and reset updates from Sebastian Reichel:
- Microsemi Ocelot reset support
- Spreadtrum SC27xx reset support
- generic gpio charger: lot's of cleanups
- axp20x fuel gauge: add AXP813 support
- misc fixes, including one devicetree change for the Nokia N900, that
has been Acked-by Tony Lindgren
* tag 'for-v4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (27 commits)
power: reset: at91-reset: Switch from the pr_*() to the dev_*() logging functions
power: reset: at91-poweroff: Remove redundant dev_err call in at91_poweroff_probe()
power: reset: at91-poweroff: Switch from the pr_*() to the dev_*() logging functions
power: reset: make function sc27xx_poweroff_shutdown static
power: supply: da9150-fg: remove VLA usage
ARM: dts: omap3-n900: Add link between battery and charger
power: supply: bq2415x: add DT referencing support
power: supply: bq27xxx: support missing supplier device
max17042: propagate of_node to power supply device
power: supply: axp288_fuel_gauge: Fix full status reporting
power: supply: axp288_fuel_gauge: Do not register FG on ECS EF20EA
power: reset: gpio-poweroff: Support for timeout from device property
dt-bindings: power: reset: gpio-poweroff: Add 'timeout-ms' property
power: reset: Add Spreadtrum SC27xx PMIC power off support
power: supply: axp20x_battery: add support for AXP813
dt-bindings: power: supply: axp20x: add AXP813 battery DT binding
power: supply: axp20x_battery: use data struct for variant specific code
power: supply: gpio-charger: Remove pdata from gpio_charger
power: supply: gpio-charger: Use GPIOF_ACTIVE_LOW for legacy setup
power: supply: gpio-charger: Remove redundant dev_err call in probe function
...
- Modify the cpuidle poll state implementation to prevent CPUs from
staying in the loop in there for excessive times (Rafael Wysocki).
- Add Intel Cannon Lake chips support to the RAPL power capping
driver (Joe Konno).
- Add reference counting to the device links handling code in the
PM core (Lukas Wunner).
- Avoid reconfiguring GPEs on suspend-to-idle in the ACPI system
suspend code (Rafael Wysocki).
- Allow devices to be put into deeper low-power states via ACPI
if both _SxD and _SxW are missing (Daniel Drake).
- Reorganize the core ACPI suspend-to-idle wakeup code to avoid a
keyboard wakeup issue on Asus UX331UA (Chris Chiu).
- Prevent the PCMCIA library code from aborting suspend-to-idle due
to noirq suspend failures resulting from incorrect assumptions
(Rafael Wysocki).
- Add coupled cpuidle supprt to the Exynos3250 platform (Marek
Szyprowski).
- Add new sysfs file to make it easier to specify the image storage
location during hibernation (Mario Limonciello).
- Add sysfs files for collecting suspend-to-idle usage and time
statistics for CPU idle states (Rafael Wysocki).
- Update the pm-graph utilities (Todd Brandt).
- Reduce the kernel log noise related to reporting Low-power Idle
constraings by the ACPI system suspend code (Rafael Wysocki).
- Make it easier to distinguish dedicated wakeup IRQs in the
/proc/interrupts output (Tony Lindgren).
- Add the frequency table validation in cpufreq to the core and
drop it from a number of cpufreq drivers (Viresh Kumar).
- Drop "cooling-{min|max}-level" for CPU nodes from a couple of
DT bindings (Viresh Kumar).
- Clean up the CPU online error code path in the cpufreq core
(Viresh Kumar).
- Fix assorted issues in the SCPI, CPPC, mediatek and tegra186
cpufreq drivers (Arnd Bergmann, Chunyu Hu, George Cherian,
Viresh Kumar).
- Drop memory allocation error messages from a few places in
cpufreq and cpuildle drivers (Markus Elfring).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=6JC2
-----END PGP SIGNATURE-----
Merge tag 'pm-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These update the cpuidle poll state definition to reduce excessive
energy usage related to it, add new CPU ID to the RAPL power capping
driver, update the ACPI system suspend code to handle some special
cases better, extend the PM core's device links code slightly, add new
sysfs attribute for better suspend-to-idle diagnostics and easier
hibernation handling, update power management tools and clean up
cpufreq quite a bit.
Specifics:
- Modify the cpuidle poll state implementation to prevent CPUs from
staying in the loop in there for excessive times (Rafael Wysocki).
- Add Intel Cannon Lake chips support to the RAPL power capping
driver (Joe Konno).
- Add reference counting to the device links handling code in the PM
core (Lukas Wunner).
- Avoid reconfiguring GPEs on suspend-to-idle in the ACPI system
suspend code (Rafael Wysocki).
- Allow devices to be put into deeper low-power states via ACPI if
both _SxD and _SxW are missing (Daniel Drake).
- Reorganize the core ACPI suspend-to-idle wakeup code to avoid a
keyboard wakeup issue on Asus UX331UA (Chris Chiu).
- Prevent the PCMCIA library code from aborting suspend-to-idle due
to noirq suspend failures resulting from incorrect assumptions
(Rafael Wysocki).
- Add coupled cpuidle supprt to the Exynos3250 platform (Marek
Szyprowski).
- Add new sysfs file to make it easier to specify the image storage
location during hibernation (Mario Limonciello).
- Add sysfs files for collecting suspend-to-idle usage and time
statistics for CPU idle states (Rafael Wysocki).
- Update the pm-graph utilities (Todd Brandt).
- Reduce the kernel log noise related to reporting Low-power Idle
constraings by the ACPI system suspend code (Rafael Wysocki).
- Make it easier to distinguish dedicated wakeup IRQs in the
/proc/interrupts output (Tony Lindgren).
- Add the frequency table validation in cpufreq to the core and drop
it from a number of cpufreq drivers (Viresh Kumar).
- Drop "cooling-{min|max}-level" for CPU nodes from a couple of DT
bindings (Viresh Kumar).
- Clean up the CPU online error code path in the cpufreq core (Viresh
Kumar).
- Fix assorted issues in the SCPI, CPPC, mediatek and tegra186
cpufreq drivers (Arnd Bergmann, Chunyu Hu, George Cherian, Viresh
Kumar).
- Drop memory allocation error messages from a few places in cpufreq
and cpuildle drivers (Markus Elfring)"
* tag 'pm-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (56 commits)
ACPI / PM: Fix keyboard wakeup from suspend-to-idle on ASUS UX331UA
cpufreq: CPPC: Use transition_delay_us depending transition_latency
PM / hibernate: Change message when writing to /sys/power/resume
PM / hibernate: Make passing hibernate offsets more friendly
cpuidle: poll_state: Avoid invoking local_clock() too often
PM: cpuidle/suspend: Add s2idle usage and time state attributes
cpuidle: Enable coupled cpuidle support on Exynos3250 platform
cpuidle: poll_state: Add time limit to poll_idle()
cpufreq: tegra186: Don't validate the frequency table twice
cpufreq: speedstep: Don't validate the frequency table twice
cpufreq: sparc: Don't validate the frequency table twice
cpufreq: sh: Don't validate the frequency table twice
cpufreq: sfi: Don't validate the frequency table twice
cpufreq: scpi: Don't validate the frequency table twice
cpufreq: sc520: Don't validate the frequency table twice
cpufreq: s3c24xx: Don't validate the frequency table twice
cpufreq: qoirq: Don't validate the frequency table twice
cpufreq: pxa: Don't validate the frequency table twice
cpufreq: ppc_cbe: Don't validate the frequency table twice
cpufreq: powernow: Don't validate the frequency table twice
...
* pm-cpufreq: (38 commits)
cpufreq: CPPC: Use transition_delay_us depending transition_latency
cpufreq: tegra186: Don't validate the frequency table twice
cpufreq: speedstep: Don't validate the frequency table twice
cpufreq: sparc: Don't validate the frequency table twice
cpufreq: sh: Don't validate the frequency table twice
cpufreq: sfi: Don't validate the frequency table twice
cpufreq: scpi: Don't validate the frequency table twice
cpufreq: sc520: Don't validate the frequency table twice
cpufreq: s3c24xx: Don't validate the frequency table twice
cpufreq: qoirq: Don't validate the frequency table twice
cpufreq: pxa: Don't validate the frequency table twice
cpufreq: ppc_cbe: Don't validate the frequency table twice
cpufreq: powernow: Don't validate the frequency table twice
cpufreq: p4-clockmod: Don't validate the frequency table twice
cpufreq: mediatek: Don't validate the frequency table twice
cpufreq: longhaul: Don't validate the frequency table twice
cpufreq: ia64-acpi: Don't validate the frequency table twice
cpufreq: elanfreq: Don't validate the frequency table twice
cpufreq: e_powersaver: Don't validate the frequency table twice
cpufreq: cpufreq-dt: Don't validate the frequency table twice
...
Minor conflicts in drivers/net/ethernet/mellanox/mlx5/core/en_rep.c,
we had some overlapping changes:
1) In 'net' MLX5E_PARAMS_LOG_{SQ,RQ}_SIZE -->
MLX5E_REP_PARAMS_LOG_{SQ,RQ}_SIZE
2) In 'net-next' params->log_rq_size is renamed to be
params->log_rq_mtu_frames.
3) In 'net-next' params->hard_mtu is added.
Signed-off-by: David S. Miller <davem@davemloft.net>
Here are are a couple of last-minute fixes for 4.16, mostly for
regressions. As usual, the majory are device tree changes:
- USB 3 support on rk3399 didn't work and is being reverted for now
- One fix for an old suspend/resume bug on rk3399
- A few regulator related fixes on Banana Pi M2, and on imx7d-sdb
- A boot regression fix for all Aspeed SoCs failing to find
their memory
- One more dtc warning fix
The other changes are:
- A few updates to the MAINTAINERS file
- A revert for an incorrect orion5x cleanup
- Two power management fixes for OMAP
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=qZnT
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"Here are are a couple of last-minute fixes for 4.16, mostly for
regressions. As usual, the majory are device tree changes:
- USB 3 support on rk3399 didn't work and is being reverted for now
- One fix for an old suspend/resume bug on rk3399
- A few regulator related fixes on Banana Pi M2, and on imx7d-sdb
- A boot regression fix for all Aspeed SoCs failing to find their
memory
- One more dtc warning fix
The other changes are:
- A few updates to the MAINTAINERS file
- A revert for an incorrect orion5x cleanup
- Two power management fixes for OMAP"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: OMAP: Fix SRAM W+X mapping
ARM: dts: aspeed: Add default memory node
mailmap: Update email address for Gregory CLEMENT
ARM: davinci: fix the GPIO lookup for omapl138-hawk
MAINTAINERS: Update Tegra IOMMU maintainer
ARM: dts: imx7d-sdb: Fix regulator-usb-otg2-vbus node name
ARM: ux500: Fix PMU IRQ regression
ARM: dts: rockchip: Add missing #sound-dai-cells on rk3288
Revert "arm64: dts: rockchip: add usb3-phy otg-port support for rk3399"
arm64: dts: rockchip: Fix rk3399-gru-* s2r (pinctrl hogs, wifi reset)
ARM: OMAP: Fix dmtimer init for omap1
MAINTAINERS: update email address for Maxime Ripard
ARM: dts: sun6i: a31s: bpi-m2: add missing regulators
ARM: dts: sun6i: a31s: bpi-m2: improve pmic properties
CONFIG_FORTIFY_SOURCE detects various overflows at compile-time.
(6974f0c455 ("include/linux/string.h:
add the option of fortified string.h functions)
ARCH_HAS_FORTIFY_SOURCE means that the architecture can be built and
run with CONFIG_FORTIFY_SOURCE.
Since ARM can be built and run with that flag like other architectures,
select ARCH_HAS_FORTIFY_SOURCE as default.
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Jinbum Park <jinb.park7@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
- Add missing property '#sound-dai-cells' for sgtl5000 codec node
in imx6ul-isiot board to fix warning seen with DTC 1.4.6.
- Use stdout-path instead of linux,stdout-path to fix DTC warning
reported by DTC 1.4.6.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJaqysJAAoJEFBXWFqHsHzOz24H/j3Aa6ThJAmSi4XsCSa+xZtr
8uqedh8EX+SEVXnkyhJ10g8A6qKZQ8boKAtva/7uJnIyMBDvLwIleLPRII3t1axj
qp+VrLvWUw2MV0MXlj1D9vgRm9t8/Io79bzZJrdymU8LdldV3N1Gf6xJUM/AF40k
4diFJSb4XvR1+gCp8jRKhOC65j6vPNYRLToDSqiMHMeAdVTo/CM0lp/T6Ei8BkJP
snybLF0KPt84gGBFMcmwP7bFS9r92+yxtMeac2723peIHrCrY28ho1uIAV5kX/lf
YpFpQk33ocRCV5iprF/qHgUF45Adj6IjP7EpSNnWdbcTr1FzU9mispdGZQ1MIQk=
=+/7s
-----END PGP SIGNATURE-----
Merge tag 'imx-dt-4.17-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
Pull "i.MX device tree updates for 4.17, round 2" Shawn Guo:
- Add missing property '#sound-dai-cells' for sgtl5000 codec node
in imx6ul-isiot board to fix warning seen with DTC 1.4.6.
- Use stdout-path instead of linux,stdout-path to fix DTC warning
reported by DTC 1.4.6.
* tag 'imx-dt-4.17-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx6ul-isiot: Pass the required '#sound-dai-cells'
ARM: dts: imx6-phytec: Use the standard 'stdout-path' property
- add syscon property to sound nodes
- add more ethernet pin groups
- add ethernet support for PXs3 SoC
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=5fxa
-----END PGP SIGNATURE-----
Merge tag 'uniphier-dt-v4.17-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier into next/dt
Pull "UniPhier ARM SoC DT updates for v4.17 (2nd)" from Masahiro Yamada:
- add syscon property to sound nodes
- add more ethernet pin groups
- add ethernet support for PXs3 SoC
* tag 'uniphier-dt-v4.17-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier:
arm64: dts: uniphier: add ethernet node for PXs3
ARM: dts: uniphier: add pinctrl groups of ethernet for second instance
ARM: dts: uniphier: add syscon property for UniPhier sound system
arm64: dts: uniphier: add syscon property for UniPhier sound system
compatible set. Other than that there are some board-specific changes
like the Rock2 getting its otg port, recovery and power keys enabled.
The vyasa board gained an enabled emmc node and the phyCORE boards
got UHS speeds in their sd card and a fixed sd-card power supply.
Finally the veyron boards dropped a nonstandard and unused property.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAlqpSxAQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgTe4B/48XJWZy0NzXFKHDfpgvuBzyM4BdvqHaNcz
6ADlLxt1r0f1EajUfuxBn3WhLAB2QniQV5gYqs5yjBucOQGHJ0OscZsfZIC7+Ee1
xEYbA+2TJh+clZp6h+b6fW92fJnyb43c7AuW8DOVH+44oodd3xEbq0wBKm0e2elV
fFgCAabo4AhtNSdl/yVBJOVkhPnC/23kphrDQh5Ky8d/GDBZDPg4KBuAiQrvS6qv
T90pSQqwvqgnAZEf/zNgWwmty626KvnKExw7D5dtSNk+JxtYRuMdkUZhRSw2OLaW
uThRyn78Tzie/5XqtX11gHR2HVY+Q4d/T3m5CfSDGtcJW4oc29gg
=NuPe
-----END PGP SIGNATURE-----
Merge tag 'v4.17-rockchip-dts32-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Pull "Rockchip dts32 changes for 4.17" from Heiko Stübner:
For general soc-specific changes the rk322x socs got their correct grf
compatible set. Other than that there are some board-specific changes
like the Rock2 getting its otg port, recovery and power keys enabled.
The vyasa board gained an enabled emmc node and the phyCORE boards
got UHS speeds in their sd card and a fixed sd-card power supply.
Finally the veyron boards dropped a nonstandard and unused property.
* tag 'v4.17-rockchip-dts32-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: enable USB-OTG port on Radxa Rock2 Square
ARM: dts: rockchip: add recovery button for Rock2 Square
ARM: dts: rockchip: add power key for Rock2 Square
ARM: dts: rockchip: Add eMMC node for rk3288-vyasa
ARM: dts: rockchip: Support UHS mode for SD card on phyCORE-RK3288 RDK
ARM: dts: rockchip: Fix supply node for card's power on phycore som
ARM: dts: rockchip: add "rockchip,rk3228-grf" compatible for rk322x grf node
ARM: dts: rockchip: drop veyron's nonstandard 'backlight-boot-off'
Pull ARM fixes from Russell King:
"A small number of small fixes for ARM, mostly for some build issues.
One fix for a regression caused by the cpu hotplug conversion from a
few kernel versions ago"
* 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8750/1: deflate_xip_data.sh: minor fixes
ARM: 8748/1: mm: Define vdso_start, vdso_end as array
ARM: 8747/1: make CONFIG_DEBUG_WX depend on MMU
ARM: 8746/1: vfp: Go back to clearing vfp_current_hw_state[]
Add pinctrl groups of ethernet, such as "ether1_rgmii" and "ether1_rmii".
These are used for second ethernet instance.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
convert to the SPDX-License-Identifier for the Kirkwood and the Armada
based device tree files.
Compared to the series submitted most of the patch have been squashed:
the result is grouped by SoC, boards, type of licenses and the patches
that were explicitly acked on the mailing list.
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCWrpPYAAKCRALBhiOFHI7
1b10AKCqxQyhPL57/amGFttPsuQjt7NQywCfazQFhamjz1xsA9ghrUHu+dXhigQ=
=PEH4
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt-4.17-spdx' of git://git.infradead.org/linux-mvebu into next/dt
Pull "mvebu SPDX dt for 4.17: from Gregory CLEMENT:
convert to the SPDX-License-Identifier for the Kirkwood and the Armada
based device tree files.
Compared to the series submitted most of the patch have been squashed:
the result is grouped by SoC, boards, type of licenses and the patches
that were explicitly acked on the mailing list.
* tag 'mvebu-dt-4.17-spdx' of git://git.infradead.org/linux-mvebu:
arm: dts: kirkwood*.dts: use SPDX-License-Identifier for board using GPL-2.0+
arm: dts: kirkwood*.dts: use SPDX-License-Identifier for boards using GPL-2.0+/MIT
arm: dts: kirkwood*.dts: use SPDX-License-Identifier for boards using GPL-2.0
arm: dts: armada-385-turris-omnia: use SPDX-License-Identifier
arm: dts: armada-385-db-ap: use SPDX-License-Identifier
arm: dts: armada-388-rd: use SPDX-License-Identifier
arm: dts: armada-xp-db-xc3-24g4xg: use SPDX-License-Identifier
arm: dts: armada-xp-db-dxbc2: use SPDX-License-Identifier
arm: dts: armada-370-db: use SPDX-License-Identifier
arm: dts: armada-*.dts: use SPDX-License-Identifier for most of the Armada based board
arm: dts: armada-xp-98dx: use SPDX-License-Identifier for prestara 98d SoCs
arm: dts: armada-*.dtsi: use SPDX-License-Identifier for most of the Armada SoCs
- add SFP module support on the clearfog (Armada 388 based board)
- disable internal RTC node for Linksys boards (Armada 38x based
boards)
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCWrpOUQAKCRALBhiOFHI7
1a2+AJ0VfGuYnH3LI8Za6QIGseKKnZrJLgCggcegrw/ntOcu8cr9kqrH2BOqOhg=
=Ebj2
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt-4.17-2' of git://git.infradead.org/linux-mvebu into next/dt
Pull "mvebu dt for 4.17 (part 2)" from Gregory CLEMENT:
- add SFP module support on the clearfog (Armada 388 based board)
- disable internal RTC node for Linksys boards (Armada 38x based
boards)
* tag 'mvebu-dt-4.17-2' of git://git.infradead.org/linux-mvebu:
ARM: dts: armada388-clearfog: add SFP module support
ARM: dts: armada-385-linksys: Disable internal RTC
Follow the recent trend for the license description
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Follow the recent trend for the license description, and also fix the
wrongly stated X11 to MIT.
As already pointed on the DT ML, the X11 license text [1] is explicitly
for the X Consortium and has a couple of extra clauses. The MIT
license text [2] is actually what the current DT files claim.
[1] https://spdx.org/licenses/X11.html
[2] https://spdx.org/licenses/MIT.html
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Follow the recent trend for the license description
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Follow the recent trend for the license description, and also fix the
wrongly stated X11 to MIT.
As already pointed on the DT ML, the X11 license text [1] is explicitly
for the X Consortium and has a couple of extra clauses. The MIT
license text [2] is actually what the current DT files claim.
[1] https://spdx.org/licenses/X11.html
[2] https://spdx.org/licenses/MIT.html
Cc: Uwe Kleine-König <uwe@kleine-koenig.org>
Acked-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Follow the recent trend for the license description, and also fix the
wrongly stated X11 to MIT.
As already pointed on the DT ML, the X11 license text [1] is explicitly
for the X Consortium and has a couple of extra clauses. The MIT
license text [2] is actually what the current DT files claim.
[1] https://spdx.org/licenses/X11.html
[2] https://spdx.org/licenses/MIT.html
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Follow the recent trend for the license description, and also fix the
wrongly stated X11 to MIT.
As already pointed on the DT ML, the X11 license text [1] is explicitly
for the X Consortium and has a couple of extra clauses. The MIT
license text [2] is actually what the current DT files claim.
[1] https://spdx.org/licenses/X11.html
[2] https://spdx.org/licenses/MIT.html
Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Follow the recent trend for the license description, and also fix the
wrongly stated X11 to MIT.
As already pointed on the DT ML, the X11 license text [1] is explicitly
for the X Consortium and has a couple of extra clauses. The MIT
license text [2] is actually what the current DT files claim.
[1] https://spdx.org/licenses/X11.html
[2] https://spdx.org/licenses/MIT.html
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
Acked-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Follow the recent trend for the license description, and also fix the
wrongly stated X11 to MIT.
As already pointed on the DT ML, the X11 license text [1] is explicitly
for the X Consortium and has a couple of extra clauses. The MIT
license text [2] is actually what the current DT files claim.
[1] https://spdx.org/licenses/X11.html
[2] https://spdx.org/licenses/MIT.html
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
Acked-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Follow the recent trend for the license description, and also fix the
wrongly stated X11 to MIT.
As already pointed on the DT ML, the X11 license text [1] is explicitly
for the X Consortium and has a couple of extra clauses. The MIT
license text [2] is actually what the current DT files claim.
[1] https://spdx.org/licenses/X11.html
[2] https://spdx.org/licenses/MIT.html
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Follow the recent trend for the license description, and also fix the
wrongly stated X11 to MIT.
As already pointed on the DT ML, the X11 license text [1] is explicitly
for the X Consortium and has a couple of extra clauses. The MIT
license text [2] is actually what the current DT files claim.
[1] https://spdx.org/licenses/X11.html
[2] https://spdx.org/licenses/MIT.html
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Follow the recent trend for the license description, and also fix the
wrongly stated X11 to MIT.
As already pointed on the DT ML, the X11 license text [1] is explicitly
for the X Consortium and has a couple of extra clauses. The MIT
license text [2] is actually what the current DT files claim.
[1] https://spdx.org/licenses/X11.html
[2] https://spdx.org/licenses/MIT.html
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
Acked-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Follow the recent trend for the license description, and also fix the
wrongly stated X11 to MIT.
As already pointed on the DT ML, the X11 license text [1] is explicitly
for the X Consortium and has a couple of extra clauses. The MIT
license text [2] is actually what the current DT files claim.
[1] https://spdx.org/licenses/X11.html
[2] https://spdx.org/licenses/MIT.html
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Add SFP module support for Clearfog using the SFP phylink support.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
The internal RTC does not work correctly on these Linksys boards based
on Marvell SoCs. For me it only shows Wed Dec 31 23:59:59 1969 and for
others it is off by 3 minutes in 10 minutes running, this was reported
by multiple users. On the Linksys Mamba device the device tree comment
says that no crystal is connected to the internal RTC, this is probably
also true for the other devices.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
