The users of the old method are now converted to the new one.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
[ kishon@ti.com : made phy-berlin-usb.c and phy-miphy28lp.c to use the updated
devm_phy_create API.]
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The pin controllers of Exynos4415 are similar to Exynos4412, but certain
differences cause the need to create separate driver data for it. This
patch adds pin controller and bank descriptor arrays to the driver to
support the new SoC.
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Thomas Abraham <thomas.abraham@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
[cw00.choi: Rebase it on mainline kernel]
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
[tomasz.figa@gmail.com: Resolved merge with earlier clean-up series.]
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
This patch adds initial driver data for Exynos7 pinctrl support.
Signed-off-by: Naveen Krishna Ch <naveenkrishna.ch@gmail.com>
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Reviewed-by: Thomas Abraham <thomas.ab@samsung.com>
Tested-by: Thomas Abraham <thomas.ab@samsung.com>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Exynos7 uses different offsets for wakeup interrupt configuration registers.
So a new irq_chip instance for Exynos7 wakeup interrupts is added. The irq_chip
selection is now based on the wakeup interrupt controller compatible string.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Reviewed-by: Thomas Abraham <thomas.ab@samsung.com>
Tested-by: Thomas Abraham <thomas.ab@samsung.com>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Adding a irq_chip field to the samsung_pin_bank struct helps in
consolidating the irq domain callbacks for external gpio and wakeup
interrupt controllers. The exynos_wkup_irqd_ops and exynos_gpio_irqd_ops
have now been merged into a single exynos_eint_irqd_ops.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Reviewed-by: Thomas Abraham <thomas.ab@samsung.com>
Tested-by: Thomas Abraham <thomas.ab@samsung.com>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
The function exynos_irq_demux_eint16_31 uses pre-defined offsets for external
interrupt pending status and mask registers. So this function is not extensible
for Exynos7 SoC which has these registers at different offsets. Generalize
the exynos_irq_demux_eint16_31 function by using the pending/mask register
offset values from the exynos_irq_chip structure. This is done by adding a
irq_chip field to the samsung_pin_bank struct.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Reviewed-by: Thomas Abraham <thomas.ab@samsung.com>
Tested-by: Thomas Abraham <thomas.ab@samsung.com>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Currently the driver mixes constant init data with runtime data, which
is far from being elegant and can invite potential hard to track issues.
This patch intends to solve this by introducing a new
samsung_pin_bank_data structure to hold only constant data known at
compile time, which can be copied to main samsung_pin_bank struct used
at runtime.
In addition, thanks to this change, all per-bank initdata can be marked
with const and __initconst keywords and dropped after init completes.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
In order to separate initialization constants from runtime data, this
patch modifies the driver to store only constant data in
samsung_pin_ctrl struct and copy data required at runtime to
samsung_pinctrl_drv_data struct. This makes it possible to mark all
existing instances of samsung_pin_ctrl struct as const and __initconst.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
This structure is not intended to be modified at runtime and functions
as constant data shared between multiple pin banks. This patch makes all
instances of it constant across the driver.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
There is no code using it and in fact there are pin controller variants
that do not even have this field initialized in their init data. This
patch removes it completely.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Currently the function returns a valid pointer on success and NULL on
error, so exact error code is lost. This patch changes return convention
of the function to use ERR_PTR() on error instead.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
This driver supports the pin/GPIO controllers found in newer Intel SoCs
like Cherryview and Braswell. The driver provides full GPIO support and
minimal set of pin controlling funtionality.
The driver is based on the original Cherryview GPIO driver authored by Ning
Li and Alan Cox.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
functions from Chris Zhong
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCAAGBQJUVpbfAAoJEPOmecmc0R2Bl14H/Rwmpp+KUPcudzSMpnfcqSKt
s8B/EVa7I/eURz+5ZFg6kbkTYsT0N/81vGG3MbLT6609iHsxkfClYHkX2JQNBqIn
mDYKCpbKPWxS0OrAhYPqG5ywiKEYWZb95DRRoXX7TKh7SFC+5nb/MC9gYtd0kKx4
4fibILzOteN7Besvu+Ma8JkPJZR6/sebFkGj51Rpucff91qkiicy4nSEdCwSq2F5
8neEX95FQlmf1rSPcdt2GY4hEvPAJBe9R2EPIaPy77p0uy3POmgMJNyK7d2b2dxU
mV/AP2Pc71OPIfmKYP9LlWPP3AWS1thA8kFEEUjDJvaSVX5qbJggmptVFWQ884o=
=/WZL
-----END PGP SIGNATURE-----
Merge tag 'v3.19-rockchip-pinctrl1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into devel
Rockchip-pinctrl fixes from Doug Anderson and suspend-specific
functions from Chris Zhong
Save and restore the gpio6_c6 pinmux setting, since Maskrom of RK3288
would modify it to sdmmc0_det, so it need to be restored to the correct
setting after resume from Maskrom.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Tested-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
support suspend/resume of pinctrl, it allows handling sleep mode
for hogged pins in pinctrl
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Tested-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The A80 has a rather usual pin controller, the only thing out of the ordinary
being that it has 5 interrupts banks, and that some pins have several options
for the same functions.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The A80 R-PIO controller has one more bank that what we've seen so far, add the
PN pin bank.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The mxs pinctrl driver cannot handle when functions are not grouped by
name (which IMO is a bug). This happens for example if a
imx28-somemachine.dts provides a function that has the same name as a
function defined in imx28.dtsi.
The proper way to fix that would be to check for duplicates in the loops
(which increases parsing time) or parse the groups first and sort the
resulting array.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There were a few instances where the rockchip pinctrl driver would do
read-modify-write with no spinlock. Add a spinlock for these cases.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Just like in (529301c pinctrl: samsung: Parse pin groups before
calling pinctrl_register()), Rockchip also needs to parse pin groups
earlier to make hogs work.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The Rockchip pinctrl driver was calling
rockchip_gpio_direction_output() in the pin_config_set() callback.
This was just a shortcut for:
* rockchip_gpio_set()
* pinctrl_gpio_direction_output()
Unfortunately it's not so good to call pinctrl_gpio_direction_output()
from pin_config_set(). Specifically when initting hogs you'll get an
error.
Let's refactor a little so we can call
_rockchip_pmx_gpio_set_direction() directly.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The rockchip pinctrl driver uses irq_gc_set_wake() but doesn't setup
the .wake_enabled member. That means that we can never actually use a
pin for wakeup. When "irq_set_irq_wake()" tries to call through it
will always get a failure from set_irq_wake_real() and will then set
wake_depth to 0. Assuming you can resume you'll later get an error
message about "Unbalanced IRQ x wake disable".
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch fix company name's spelling typo in module descriptions
and a Kconfig.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Chris Snook <chris.snook@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We are going to have more pinctrl drivers for Intel hardware so separate
all our pin controller drivers to own directory.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is the pinctrl, pinmux, pinconf and gpiolib driver for the
Qualcomm MPP sub-function blocks found in the PMIC chips.
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is the pinctrl, pinmux, pinconf and gpiolib driver for the
Qualcomm GPIO sub-function blocks found in the PMIC chips.
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Copy the mach/at91_pio.h header locally and use it for pinctrl-at91.c. This
allows to remove the dependency on mach/at91_pio.h to be able to move at91 to
multiplatform.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This function actually operates on a gpio_chip, so its prefix should
reflect that fact for consistency with other functions defined in
gpio/driver.h.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When dumping pinconf information in debugfs, config arguments are only
printed when a unit is present and the argument is != 0. For parameters
like the slew rate, this does not work. The slew rate uses a driver
specific format for the argument, i.e. 0 can be a valid argument and a
unit is not provided for it.
For that reason, add a flag to enable printing the argument instead of
inferring it from the presence of a unit and the value of the argument.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pinctrl config helpers make a separate copy of the configuration, so
callers must make sure to free any dynamically allocated memory that was
used to store it.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pinctrl-baytrail driver provides a proper ->remove()
method on its platform_driver definition, however there's
no way, currently, to unload the driver due to missing
module_exit(). This patch adds module_exit().
Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add pinmux support for GPIO for Vybrid (vf610) IOMUX controller.
This is needed since direction configuration is not part of the
GPIO module in Vybrid.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Even if a gpio pin is set to output, we still need to set INPUT_EN
functionality (by clearing INPUT_EN bit) to be able to read the pin's
level.
E.g. without this change, we'll always read low level state from sysfs.
Cc: <stable@vger.kernel.org> # v3.14+
Cc: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: David Cohen <david.a.cohen@linux.intel.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This change fixes below sparse error,
drivers/pinctrl/pinctrl-st.c:1515:31: error: incompatible types for operation (>)
drivers/pinctrl/pinctrl-st.c:1515:31: left side has type void [noderef] <asn:2>*irqmux_base
drivers/pinctrl/pinctrl-st.c:1515:31: right side has type int
Cc: Maxime Coquelin <maxime.coquelin@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
CC: Linus Walleij <linus.walleij@linaro.org>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Pramod Gurav <pramod.gurav@smartplayin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is a missing MMC/SD pin for MCDATDIR2 which is routed as
alt B, add it to the MMC/SD pin group and functions.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The abx500 pin control driver supported a method of fetching the
generic config from a phandle to a separate node using the
"ste,config" as a phandle. This is not used in any device trees
and not documented in the bindings, so drop this support.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This converts the ABx500 pin controller and all associated device
trees to use the standard, generic config bindings for pin controllers.
There are no such device trees deployed in the wild so this is
safe to do to set a good example.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This converts the Nomadik pin controller and all associated device
trees to use the standard, generic config bindings for pin controllers.
There are no such device trees deployed in the wild so this is
safe to do to set a good example.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This converts the ABx500 pin controller and all associated device
trees to use the standard, generic mux bindings for pin controllers.
There are no such device trees deployed in the wild so this is
safe to do to set a good example.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This converts the Nomadik pin controller and all associated device
trees to use the standard, generic mux bindings for pin controllers.
There are no such device trees deployed in the wild so this is
safe to do to set a good example.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Direct irq en bit should be cleared for pads using io mode.
If not, the io based irq will never be detected.
However, this bit can sometimes be misconfigured (BIOS issue).
Force clearing of this bit in io mode and trigger a WARN.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
cycle:
- Increase the default ARCH_NR_GPIO from 256 to 512. This
was done to avoid having a custom <asm/gpio.h> header for
the x86 architecture - GPIO is custom and complicated
enough as it is already! We want to move to a radix to
store the descriptors going forward, and finally get rid
of this fixed array size altogether.
- Endgame patching of the gpio_remove() semantics initiated
by Abdoulaye Berthe. It is not accepted by the system that
the removal of a GPIO chip fails during e.g. reboot or
shutdown, and therefore the return value has now painfully
been refactored away. For special cases like GPIO expanders
on a hot-pluggable bus like USB, we may later add some
gpiochip_try_remove() call, but for the cases we have now,
return values are moot.
- Some incremental refactoring of the gpiolib core and ACPI
GPIO library for more descriptor usage.
- Refactor the chained IRQ handler set-up method to handle
also threaded, nested interrupts and set up the parent IRQ
correctly. Switch STMPE and TC3589x drivers to use this
registration method.
- Add a .irq_not_threaded flag to the struct gpio_chip, so
that also GPIO expanders that block but are still not
using threaded IRQ handlers.
- New drivers for the ARM64 X-Gene SoC GPIO controller.
- The syscon GPIO driver has been improved to handle the
"DSP GPIO" found on the TI Keystone 2 SoC:s.
- ADNP driver switched to use gpiolib irqchip helpers.
- Refactor the DWAPB driver to support being instantiated
from and MFD cell (platform device).
- Incremental feature improvement in the Zynq, MCP23S08,
DWAPB, OMAP, Xilinx and Crystalcove drivers.
- Various minor fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8InA
-----END PGP SIGNATURE-----
Merge tag 'gpio-v3.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO changes from Linus Walleij:
"This is the bulk of GPIO changes for the v3.18 development cycle:
- Increase the default ARCH_NR_GPIO from 256 to 512. This was done
to avoid having a custom <asm/gpio.h> header for the x86
architecture - GPIO is custom and complicated enough as it is
already! We want to move to a radix to store the descriptors going
forward, and finally get rid of this fixed array size altogether.
- Endgame patching of the gpio_remove() semantics initiated by
Abdoulaye Berthe. It is not accepted by the system that the
removal of a GPIO chip fails during eg reboot or shutdown, and
therefore the return value has now painfully been refactored away.
For special cases like GPIO expanders on a hot-pluggable bus like
USB, we may later add some gpiochip_try_remove() call, but for the
cases we have now, return values are moot.
- Some incremental refactoring of the gpiolib core and ACPI GPIO
library for more descriptor usage.
- Refactor the chained IRQ handler set-up method to handle also
threaded, nested interrupts and set up the parent IRQ correctly.
Switch STMPE and TC3589x drivers to use this registration method.
- Add a .irq_not_threaded flag to the struct gpio_chip, so that also
GPIO expanders that block but are still not using threaded IRQ
handlers.
- New drivers for the ARM64 X-Gene SoC GPIO controller.
- The syscon GPIO driver has been improved to handle the "DSP GPIO"
found on the TI Keystone 2 SoC:s.
- ADNP driver switched to use gpiolib irqchip helpers.
- Refactor the DWAPB driver to support being instantiated from and
MFD cell (platform device).
- Incremental feature improvement in the Zynq, MCP23S08, DWAPB, OMAP,
Xilinx and Crystalcove drivers.
- Various minor fixes"
* tag 'gpio-v3.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (52 commits)
gpio: pch: Build context save/restore only for PM
pinctrl: abx500: get rid of unused variable
gpio: ks8695: fix 'else should follow close brace '}''
gpio: stmpe: add verbose debug code
gpio: stmpe: fix up interrupt enable logic
gpio: staticize xway_stp_init()
gpio: handle also nested irqchips in the chained handler set-up
gpio: set parent irq on chained handlers
gpiolib: irqchip: use irq_find_mapping while removing irqchip
gpio: crystalcove: support virtual GPIO
pinctrl: bcm281xx: make Kconfig dependency more strict
gpio: kona: enable only on BCM_MOBILE or for compile testing
gpio, bcm-kona, LLVMLinux: Remove use of __initconst
gpio: Fix ngpio in gpio-xilinx driver
gpio: dwapb: fix pointer to integer cast
gpio: xgene: Remove unneeded #ifdef CONFIG_OF guard
gpio: xgene: Remove unneeded forward declation for struct xgene_gpio
gpio: xgene: Fix missing spin_lock_init()
gpio: ks8695: fix switch case indentation
gpiolib: add irq_not_threaded flag to gpio_chip
...
development series:
- New drivers for the Freescale i.MX21, Qualcomm APQ8084
pin controllers.
- Incremental new features on the Rockchip, atlas 6,
OMAP, AM437x, APQ8064, prima2, AT91, Tegra, i.MX, Berlin
and Nomadik.
- Push Freescale drivers down into their own subdirectory.
- Assorted sprays of syntax and semantic fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJUMkr3AAoJEEEQszewGV1z/xsP/1EFR6zyriyup3TuWw1kiqwH
wGuEK3i0v99INcK46l9xD65aZLaK60Z6llYAmwa2wmFCDotOr46GSW2V9bqd0RHg
6EZdDATo8Ge8j86L9oUMElbMJoKMQiVC6+YeiuhQRrFuq8TpXGoTMPeQlaEslR08
MUjIVcxRbFeQCWOgkaqjjxwgX1FPU1S9aQNxDDDPuWSwTowV0nwBpdFviAgWlouY
DDG4/WPWH7s/Ujv0MJ7MQR9Hkl6WYlcuhGWDUkcIj7f1lvxTTB37Em7daBUBwhQo
PEYmf1AtwMEWF2y1i99ExFE/YSBQjjslYe29uECvaH63PVgfRMrWgJl199NOed8Q
9GfEa+uwiV4Z4PxFZqcvsjUiNQg8SoijP4UTf9AJTuQZtebVia8OS9AFsN3XULHJ
zXGKbCUd2kH+p/0/MJUePQEDoi9bPrsIhNG/s3KYmawQ6Ua4uytPgG0lF91dvP6m
LvCnsGNDvGQUk1UUG3Lj4ZDCP42TAbjNyr27Ot/oUAygjHfjsXsZ6FFmlMCOeCRx
tV+qjW9Ng69CSLPLKHCHVMsXKliJ2Vp2Mt8cr8yFyHaMDIneRx3IqUvrZ0dzfVLq
/H3/7usvR/sEV23AI920mfPVYruIJESpBh6NKt66tPSSV2C6HP/qRTN/6tAwXqBL
rzwv2t8qu5+ic2Ae5/wk
=b4Tn
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v3.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control changes from Linus Walleij:
"This is the bulk of pin control changes for the v3.18 development
series:
- New drivers for the Freescale i.MX21, Qualcomm APQ8084 pin
controllers.
- Incremental new features on the Rockchip, atlas 6, OMAP, AM437x,
APQ8064, prima2, AT91, Tegra, i.MX, Berlin and Nomadik.
- Push Freescale drivers down into their own subdirectory.
- Assorted sprays of syntax and semantic fixes"
* tag 'pinctrl-v3.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (48 commits)
pinctrl: specify bindings for pins and groups
pinctrl: nomadik: improve GPIO debug prints
pinctrl: abx500: refactor DT parser to take two paths
pinctrl: abx500: use helpers for map allocation/free
pinctrl: alter device tree bindings for functions
pinctrl: nomadik: refactor DT parser to take two paths
pinctrl: nomadik: use utils map free function
pinctrl: nomadik: use util function to reserve maps
pinctrl: qcom: use restart_notifier mechanism for ps_hold
pinctrl: sh-pfc: sh73a0: Remove unnecessary SoC data allocation
pinctrl: berlin: fix the dt_free_map function
pinctrl: at91: disable PD or PU before enabling PU or PD
pinctrl: st: remove gpiochip in failure cases
pinctrl: at91: Fix error handling while doing gpiochio_irqchip_add
pinctrl: at91: Fix failure path in at91_gpio_probe path
pinctrl: lantiq: Release gpiochip resources in fail case
pinctrl: imx: detect uninitialized pins
pinctrl: tegra: Add MIPI pad control
pinctrl: at91: Switch to using managed clk_get
pinctrl: adi2: Remove duplicate gpiochip_remove_pin_ranges
...
commit 2fcea6cecb
"pinctrl: remove remaining users of gpiochip_remove() retval"
removed the use of the return value from gpiochip_remove()
but missed to delete the dangling "err" variable:
drivers/pinctrl/nomadik/pinctrl-abx500.c:
In function 'abx500_gpio_probe':
drivers/pinctrl/nomadik/pinctrl-abx500.c:1208:11:
warning: unused variable 'err' [-Wunused-variable]
Fix this by getting rid of the dangling variable.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The debugfs file would only define if the line was "pulled" and
not which direction (pull up or pull down). Improve this by
taking two print paths depending on whether the pin is set as
input or output and use the data register directly to figure
out whether the pin is set for pull up or pull down.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We refactor the DT parser to look for either a config or a
function and then look for further nodes and reserve maps,
not the two things mixed up like prior to this patch.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This switches the abx500 driver to use the pin control helper
utils for allocating and free:ing maps.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We refactor the DT parser to look for either a config or a
function and then look for further nodes and reserve maps,
not the two things mixed up like prior to this patch.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
By converting to the restart_notifier mechanism for restart, we allow
for other mechanisms, like the watchdog, to be used for restart in the
case where PS_HOLD has failed to reset the chip.
Since this mechanism may be one of several mechanisms registered, change
the post-ps_hold write timeout to be a more reasonable 1 second instead
of 10 seconds.
Choose priority 128, as according to documentation, this mechanism "is
sufficient to restart the entire system".
Tested-by: Pramod Gurav <pramod.gurav@smartplayin.com>
Signed-off-by: Josh Cartwright <joshc@codeaurora.org>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver is only useful on BCM281xx, so let the driver depend on
ARCH_BCM_MOBILE but allow compile coverage testing.
The main benefit is that the driver isn't available to be selected for
machines that don't have the matching hardware.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Sherman Yin <syin@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some drivers accidentally still use the return value from
gpiochip_remove(). Get rid of them so we can simplify this function
and get rid of the return value.
Cc: Abdoulaye Berthe <berthe.ab@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The SoC data structure allocated at init time only holds a regulator
pointer that is only used in the init function. Replace it with a local
variable and get rid of the SoC data structure allocation altogether.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The berlin_pinctrl_dt_free_map function tries to free memory
allocated and handled by the of subsystem. This is wrong and
already handled by pinctrl_dt_free_maps() which calls
of_node_put().
This patch fixes the Berlin pinctrl way of freeing its maps,
avoiding a kernel BUG(), by using the common
pinctrl_utils_dt_free_map function instead.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Disable Pull-Down or Pull-Up property before enabling Pull-Up or
Pull-Down, because the pin's Pull-Up and Pull-Down property is
mutually exclusive.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch removes a call to panic function when gpiochio_irqchip_add
fails and just returns the error to the calling function.
Same return value is used to handle the error case and adds a lable
to release resources on error.
The error message has been improved to indicate failure to add irqchip
to gpiochip.
This also changes first argument to function at91_gpio_of_irq_setup from
struct device_node to struct platform_device. Because The device_node
argument was anyway not being used. Passed pdev so that on failure dev_err
can use &pdev->dev and log can be associated with proper device.
CC: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
CC: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Pramod Gurav <pramod.gurav@smartplayin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This fixes the whole error handling in probe function by capturing and
returning error values on kernel function like clk_prepare,
clk_enable, gpiochip_add etc.
CC: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
CC: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Pramod Gurav <pramod.gurav@smartplayin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pinctrl driver initialized the register offsets for the pins
with 0. On Vybrid an offset of 0 is a valid offset for the pinctrl
mux register. So far, this was solved using the ZERO_OFFSET_VALID
flag which allowed offsets of 0. However, this does not allow to
verify whether a pins struct imx_pmx_func was initialized or not.
Use signed offset values for register offsets and initialize those
with -1 in order to detect uninitialized offset values reliable.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds MIPI CSI/DSIB pad control mux register
from the APB misc block to tegra pinctrl.
Without writing to this register, the dsib pads are
muxed as csi, and cannot be used.
The register is not yet documented in the TRM, here is
the description:
70000820: APB_MISC_GP_MIPI_PAD_CTRL_0
[31:02] RESERVED
[01:01] DSIB_MODE [CSI=0,DSIB=1]
[00:00] RESERVED
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the IRQCHIP_SKIP_SET_WAKE flag to baytrail gpio irq_chip
to resolve unbalaced IRQ wake disable warnings.
Suggested-by: Borun Fu <borun.fu@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch switches to using managed version of clk_get and hence
removes clk_put from failure path.
CC: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
CC: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Pramod Gurav <pramod.gurav@smartplayin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch removes call to gpiochip_remove_pin_ranges() from
platform_driver remove function as it will anway be called
by gpiochip_remove().
CC: Sonic Zhang <sonic.zhang@analog.com>
CC: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Pramod Gurav <pramod.gurav@smartplayin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
commit 03e9f0cac5
"pinctrl: clean up after enable refactoring"
renamed the vtable callback .enable to .set_mux. The
renaming was done manually, and one of the alterations
contained a freudian slip. I confess, I am human.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The SAMA5 and SAM9x5 series both have drive strength
options for the PIOs. This patch adds the ability to set
one of three hardware options for drive strengths of low,
medium or high for the each pin. The actual current output
of the chip based on the setting is defined in the datasheets
and varies per pins separate from banks and with supply
voltage.
This patch adds three new dt-bindings that allow setting the
strength when configuring pins. By default, no change will
be made to the drive strength of a pin from its reset value.
Due to the difference between the register addresses of the
SAMA5 and SAM9x5 series, a new sama5d3-pinctrl id was added.
Signed-off-by: Marek Roszko <mark.roszko@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
we have done that for atlas6 in commit ed36c1a, 086b8904 etc. here we
do same things for prima2.
Signed-off-by: Rongjun Ying <rongjun.ying@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently the value used to specify that interrupts from the gpio should
be routed to the application processor is hardcoded for all Qualcomm SoCs.
But the new APQ8084 SoC uses a different value. To resolve this, we make
this value configurable for each SoC. For all existing SoCs we continue
to use the current value, and only for APQ8084 we use the new value.
Suggested-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Georgi Djakov <gdjakov@mm-sol.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patchset adds pinctrl support for the Qualcomm APQ8084 platform.
This set of patches adds pinctrl support for the Qualcomm APQ8084 platform.
The first patch adds the pin definitions. The second patch contains the
devicetree binding documentation. The third patch adds the DT node.
The last patch makes the INTR_TARGET_PROC_APPS value configurable and
defines it for each existing SoC.
Tested on IFC6540 board.
Changes since v3:
- Fixed the sdc valid pin values in the binding documentation - sdc2
instead of sdc3. (suggested by Bjorn Andersson)
Changes since v2:
- Fixed some incorrect bits and offsets. (suggested by Bjorn Andersson)
- Updated binding documentation to follow the format of msm8960.
(suggested by Bjorn Andersson)
- Added fourth patch, which removes the hardcoded INTR_TARGET_PROC_APPS
value and makes it configurable. Also we keep the current value for
existing SoCs. (suggested by Bjorn Andersson)
Changes since v1:
- Updated the total number of pins (suggested by Bjorn Andersson)
- Added the missing pin info (provided by Andy Gross)
- Updated groups and functions to be consistent with other pinctrls.
(suggested by Andy Gross)
- Removed unused functions, qdss and test pins. (suggested by Andy Gross)
- Updated the documentation with the possible functions.
Reviewed-by: Andy Gross <agross@codeaurora.org>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Georgi Djakov <gdjakov@mm-sol.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The vtable named *pinmux_ops in the affected files are not really
about pin multiplexing, but a struct related to some PFC-specific
operations, inclusing pin config (bias setting). Rename the variable
so as to avoid confusions.
Acked-by: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This moves all the Freescale-related drivers (i.MX and MXS) to
its own subdirectory to clear the view.
Cc: Alexander Shiyan <shc_work@mail.ru>
Cc: Anson Huang <b20788@freescale.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Denis Carikli <denis@eukrea.com>
Cc: Markus Pargmann <mpa@pengutronix.de>
Cc: Greg Ungerer <gerg@uclinux.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
commit 2243a87d90
"pinctrl: avoid duplicated calling enable_pinmux_setting for a pin"
removed the .disable callback from the struct pinmux_ops,
making the .enable() callback the only remaining callback.
However .enable() is a bad name as it seems to imply that a
muxing can also be disabled. Rename the callback to .set_mux()
and also take this opportunity to clean out any remaining
mentions of .disable() from the documentation.
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Acked-by: Fan Wu <fwu@marvell.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds support for reset functions to reboot the boards
with soc apq8064.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: "Ivan T. Ivanov" <iivanov@mm-sol.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Andy Gross <agross@codeaurora.org>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Pramod Gurav <pramod.gurav@smartplayin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch releases gpiochip related resources by calling
gpiochip_remove when either of gpiochip_add_pin_range and
gpiochip_irqchip_add fails.
CC: Linus Walleij <linus.walleij@linaro.org>
CC: "Ivan T. Ivanov" <iivanov@mm-sol.com>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Pramod Gurav <pramod.gurav@smartplayin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is currently a kludge to get the Makefile to move down
to sh-pfc:s drivers: the arch definitions are used twice to
get it done. However we can very well use the Kconfig symbol
for the SH PFC pin control feature itself: it doesn't matter
that it comes from a lower leaf in the Kconfig hierarchy which
is completely orthogonal.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Samsung Exynos7 is a ARM64bit processor. Which does not select
the CONFIG_PLAT_SAMSUNG symbol. CONFIG_PINCTRL_SAMSUNG is being
selected for both PLAT_SAMSUNG and ARCH_EXYNOS7 symbols.
This patch modifes the pinctrl/Makefile to use
CONFIG_PINCTRL_SAMSUNG symbol to compile the pinctrl/samsung/*.c
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Cc: Tomasz Figa <t.figa@samsung.com>
Cc: linus.walleij@linaro.org
Cc: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
AM437x pinctrl definitions now differ from traditional 16 bit OMAP pin
ctrl definitions, in that all 32 bits are used to describe a single pin
Also the location of wakeupenable and event bits have changed.
Signed-off-by: Keerthy <j-keerthy@ti.com>
[nm@ti.com: minor updates]
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
DRA7 pinctrl definitions now differ from traditional 16 bit OMAP pin
ctrl definitions, in that all 32 bits are used to describe a single pin
Also the location of wakeupenable and event bits have changed.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The I2S controller can use the external clock as reference clock with
master mode. But based on different hardware or software design, this
external clock might be needed or not needed.
So the external input pin can be an independent pinctrl group, and the
card driver can decice to get it or not.
Signed-off-by: Rongjun Ying <rongjun.ying@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The I2S controller can output mclk to external audio codec. But by
hardware design, some codecs need mclk and some codecs do not need
mclk. So the mclk pin can be an independent pinctrl group, and the
card driver can get it or not based on boards.
Signed-off-by: Rongjun Ying <rongjun.ying@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
According to key customer's requirement, fix "line over 80
characters".
Signed-off-by: Bin Shi <Bin.Shi@csr.com>
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Enable autoloading of pinctrl-imx6sl module when a corresponing DT entry is present.
Signed-off-by: Kiran Padwal <kiran.padwal@smartplayin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Make of_device_id array const, because all OF functions handle it as
const.
Signed-off-by: Kiran Padwal <kiran.padwal21@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently after configuring a GPIO pin as an interrupt related pinmux
registers are changed, but there is no protection from calling
gpio_direction_*() in a badly written driver, which would cause the same
pinmux register to be reconfigured for regular input/output and this
disabling interrupt capability of the pin.
This patch addresses this issue by moving pinmux reconfiguration to
.irq_{request,release}_resources() callback of irq_chip and calling
gpio_lock_as_irq() helper to prevent reconfiguration of pin direction.
Setting up a GPIO interrupt on Samsung SoCs is a two-step operation -
in addition to trigger configuration in a dedicated register, the pinmux
must be also reconfigured to GPIO interrupt, which is a different function
than normal GPIO input, although I/O-wise they both behave in the same way
and gpio_get_value() can be used on a pin configured as IRQ as well.
Such design implies subtleties such as gpio_direction_input() not having
to fail if a pin is already configured as an interrupt nor change the
configuration to normal input. But the FLAG_USED_AS_IRQ set in gpiolib by
gpio_lock_as_irq() is only used to check that gpio_direction_output() is
not called, it's not used to prevent gpio_direction_input() to be called.
So this is not a complete solution for Samsung SoCs but it's definitely a
move in the right direction.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
[javier: use request resources instead of startup and expand commit message]
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The prefix suggests the number should be printed in hex, so use
the %x specifier to do that.
Found by using regex suggested by Joe Perches.
Signed-off-by: Hans Wennborg <hans@hanshq.net>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pctldev can't be NULL at this stage so remove the check
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is a cut and paste bug so we test the wrong variable. "err" is
never less than zero at this point.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On rk3288, for gpio bank 0, the registers which configure pull-up,
iomux, and drive strength don't implement the enable bits in the upper
half of the register, unlike the other gpio configuration registers,
and so the kernel must perform a read-modify-write of the register to
update a particular gpio in that bank.
The current code is actually clobbering the contents of the register,
so this fixes it by using regmap_update_bits and masking out only the
bits which require updating. In the case of bank0 on rk3288 the upper
enable bits will just get ignored, and the other configurations won't
get clobbered.
Signed-off-by: Sonny Rao <sonnyrao@chromium.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
I had made last-minute changes before submitting the patch "sh-pfc: r8a7791:
add CAN pin groups"; now I'm seeing that they weren't complete: I had missed
update to the pin group names in pin[01]_groups[]. Drop the "_a" suffixes there.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A handful of driver-related changes. We've had a bunch of them going in through
other branches as well, so it's only a part of what we really have this release.
Larger pieces are:
* Removal of a now unused PWM driver for atmel
- This includes AVR32 changes that have been appropriately acked.
* Performance counter support for the arm CCN interconnect
* OMAP mailbox driver cleanups and consolidation
* PCI and SATA PHY drivers for SPEAr 13xx platforms
* Redefinition (with backwards compatibility!) of PCI DT bindings for Tegra to
better model regulators/power.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=fsP6
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver changes from Olof Johansson:
"A handful of driver-related changes. We've had a bunch of them going
in through other branches as well, so it's only a part of what we
really have this release.
Larger pieces are:
- Removal of a now unused PWM driver for atmel
[ This includes AVR32 changes that have been appropriately acked ]
- Performance counter support for the arm CCN interconnect
- OMAP mailbox driver cleanups and consolidation
- PCI and SATA PHY drivers for SPEAr 13xx platforms
- Redefinition (with backwards compatibility!) of PCI DT bindings for
Tegra to better model regulators/power"
Note: this merge also fixes up the semantic conflict with the new
calling convention for devm_phy_create(), see commit f0ed817638 ("phy:
core: Let node ptr of PHY point to PHY and not of PHY provider") that
came in through Greg's USB tree.
Semantic merge patch by Stephen Rothwell <sfr@canb.auug.org.au> through
the next tree.
* tag 'drivers-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (38 commits)
bus: arm-ccn: Fix error handling at event allocation
mailbox/omap: add a parent structure for every IP instance
mailbox/omap: remove the private mailbox structure
mailbox/omap: consolidate OMAP mailbox driver
mailbox/omap: simplify the fifo assignment by using macros
mailbox/omap: remove omap_mbox_type_t from mailbox ops
mailbox/omap: remove OMAP1 mailbox driver
mailbox/omap: use devm_* interfaces
bus: ARM CCN: add PERF_EVENTS dependency
bus: ARM CCN PMU driver
PCI: spear: Remove spear13xx_pcie_remove()
PCI: spear: Fix Section mismatch compilation warning for probe()
ARM: tegra: Remove legacy PCIe power supply properties
PCI: tegra: Remove deprecated power supply properties
PCI: tegra: Implement accurate power supply scheme
ARM: SPEAr13xx: Update defconfigs
ARM: SPEAr13xx: Add pcie and miphy DT nodes
ARM: SPEAr13xx: Add bindings and dt node for misc block
ARM: SPEAr13xx: Fix static mapping table
phy: Add drivers for PCIe and SATA phy on SPEAr13xx
...
Unlike the board branch, this keeps having large sets of changes for
every release, but that's quite expected and is so far working well.
Most of this is plumbing for various device bindings and new platforms,
but there's also a bit of cleanup and code removal for things that
are moved from platform code to DT contents (some OMAP clock code in
particular).
There's also a pinctrl driver for tegra here (appropriately acked),
that's introduced this way to make it more bisectable.
I'm happy to say that there were no conflicts at all with this branch
this release, which means that changes are flowing through our tree as
expected instead of merged through driver maintainers (or at least not
done with conflicts).
There are several new boards added, and a couple of SoCs. In no particular
order:
* Rockchip RK3288 SoC support, including DTS for a dev board that they
have seeded with some community developers.
* Better support for Hardkernel Exynos4-based ODROID boards.
* CCF conversions (and dtsi contents) for several Renesas platforms.
* Gumstix Pepper (TI AM335x) board support
* TI eval board support for AM437x
* Allwinner A23 SoC, very similar to existing ones which mostly has
resulted in DT changes for support. Also includes support for an Ippo
tablet with the chipset.
* Allwinner A31 Hummingbird board support, not to be confused with the
SolidRun i.MX-based Hummingboard.
* Tegra30 Apalis board support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=xxlY
-----END PGP SIGNATURE-----
Merge tag 'dt-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device-tree changes from Olof Johansson:
"Unlike the board branch, this keeps having large sets of changes for
every release, but that's quite expected and is so far working well.
Most of this is plumbing for various device bindings and new
platforms, but there's also a bit of cleanup and code removal for
things that are moved from platform code to DT contents (some OMAP
clock code in particular).
There's also a pinctrl driver for tegra here (appropriately acked),
that's introduced this way to make it more bisectable.
I'm happy to say that there were no conflicts at all with this branch
this release, which means that changes are flowing through our tree as
expected instead of merged through driver maintainers (or at least not
done with conflicts).
There are several new boards added, and a couple of SoCs. In no
particular order:
- Rockchip RK3288 SoC support, including DTS for a dev board that
they have seeded with some community developers.
- Better support for Hardkernel Exynos4-based ODROID boards.
- CCF conversions (and dtsi contents) for several Renesas platforms.
- Gumstix Pepper (TI AM335x) board support
- TI eval board support for AM437x
- Allwinner A23 SoC, very similar to existing ones which mostly has
resulted in DT changes for support. Also includes support for an
Ippo tablet with the chipset.
- Allwinner A31 Hummingbird board support, not to be confused with
the SolidRun i.MX-based Hummingboard.
- Tegra30 Apalis board support"
* tag 'dt-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (334 commits)
ARM: dts: Enable USB host0 (EHCI) on rk3288-evb
ARM: dts: add rk3288 ehci usb devices
ARM: dts: Turn on USB host vbus on rk3288-evb
ARM: tegra: apalis t30: fix device tree compatible node
ARM: tegra: paz00: Fix some indentation inconsistencies
ARM: zynq: DT: Clarify Xilinx Zynq platform
ARM: dts: rockchip: add watchdog node
ARM: dts: rockchip: remove pinctrl setting from radxarock uart2
ARM: dts: Add missing pinctrl for uart0/1 for exynos3250
ARM: dts: Remove duplicate 'interrput-parent' property for exynos3250
ARM: dts: Add TMU dt node to monitor the temperature for exynos3250
ARM: dts: Specify MAX77686 pmic interrupt for exynos5250-smdk5250
ARM: dts: cypress,cyapa trackpad is exynos5250-Snow only
ARM: dts: max77686 is exynos5250-snow only
ARM: zynq: DT: Remove DMA from board DTs
ARM: zynq: DT: Add CAN node
ARM: EXYNOS: Add exynos5260 PMU compatible string to DT match table
ARM: dts: Add PMU DT node for exynos5260 SoC
ARM: EXYNOS: Add support for Exynos5410 PMU
ARM: dts: Add PMU to exynos5410
...
development cycle:
- Get rid of the .disable() callback from the driver callback
vtable. This callback was abused and counterintuitive since
a pin or group of pins can be said to always be in some
setting, and never really disabled. We now only enable a
certain muxing, and move between some certain muxings, we
never "disable" a mux setting.
- Some janitorial moving the MSM, Samsung and Nomadik and
drivers to their own subdirectories for a clearer view in
the subsystem. This will continue.
- Kill off the use of the return value from gpiochip_remove(),
this will be done in parallel in the GPIO subsystem and
hopefully not trigger too many unchecked return value
warnings before we get rid of this altogether.
- A huge set of changes and improvements to the Allwinner
sunxi drivers especially for their latest A23 and A31 SoCs,
and some ground work for the new sun8i platform family.
- A large set of Rockchip driver improvements adding support
for the RK3288 SoC.
- Advances in migration of older Freescale platforms to pin
control, especially i.MX1.
- Samsung and Exynos improvements.
- Support for the Qualcomm MSM8960 SoC.
- Use the gpiolib irqchip helpers for the ST SPEAr and
Intel Baytrail drivers.
- A bunch of nice janitorial work done with cppcheck.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=t1pR
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v3.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl updates from Linus Walleij:
"This is the bulk pin control changes for the v3.17 merge development
cycle:
- get rid of the .disable() callback from the driver callback vtable.
This callback was abused and counterintuitive since a pin or group
of pins can be said to always be in some setting, and never really
disabled. We now only enable a certain muxing, and move between
some certain muxings, we never "disable" a mux setting
- some janitorial moving the MSM, Samsung and Nomadik and drivers to
their own subdirectories for a clearer view in the subsystem. This
will continue
- kill off the use of the return value from gpiochip_remove(), this
will be done in parallel in the GPIO subsystem and hopefully not
trigger too many unchecked return value warnings before we get rid
of this altogether
- a huge set of changes and improvements to the Allwinner sunxi
drivers especially for their latest A23 and A31 SoCs, and some
ground work for the new sun8i platform family
- a large set of Rockchip driver improvements adding support for the
RK3288 SoC
- advances in migration of older Freescale platforms to pin control,
especially i.MX1
- Samsung and Exynos improvements
- support for the Qualcomm MSM8960 SoC
- use the gpiolib irqchip helpers for the ST SPEAr and Intel Baytrail
drivers
- a bunch of nice janitorial work done with cppcheck"
* tag 'pinctrl-v3.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (61 commits)
pinctrl: baytrail: Convert to use gpiolib irqchip
pinctrl: sunxi: number gpio ranges starting from 0
pinctrl: sunxi: use gpiolib API to mark a GPIO used as an IRQ
pinctrl: rockchip: add drive-strength control for rk3288
pinctrl: rockchip: add separate type for rk3288
pinctrl: rockchip: set is_generic in pinconf_ops
pinctrl: msm: drop negativity check on unsigned value
pinctrl: remove all usage of gpio_remove ret val in driver/pinctl
pinctrl: qcom: Make muxing of gpio function explicit
pinctrl: nomadik: move all Nomadik drivers to subdir
pinctrl: samsung: Group all drivers in a sub-dir
sh-pfc: sh73a0: Introduce the use of devm_regulator_register
sh-pfc: Add renesas,pfc-r8a7791 to binding documentation
pinctrl: msm: move all qualcomm drivers to subdir
pinctrl: msm: Add msm8960 definitions
pinctrl: samsung: Allow pin value to be initialized using pinfunc
pinctrl: samsung: Allow grouping multiple pinmux/pinconf nodes
pinctrl: exynos: Consolidate irq_chips of GPIO and WKUP EINTs
pinctrl: samsung: Handle GPIO request and free using pinctrl helpers
pinctrl: samsung: Decouple direction setting from pinctrl
...
Instead of open-coding irqchip handling in the driver we can take advantage
of the new irqchip helpers provided by the gpiolib core.
While doing this we also make sure that we call gpiochip_irqchip_add()
after the gpiochip itself is registered as required.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pinctrl-sunxi driver originally used the pin number as the gpio
range offset. This resulted in large, bogus gpio numbers for the
new sun6i-a31-r pinctrl devices.
This patch makes the driver number the gpios ranges starting from an
offset of 0, by subtracting the pin_base number from the pin number.
This also makes the system-wide gpio number match the pin number.
Tested on sun8i with sysfs exported gpios.
This patch also changes the GPIO bindings for R_PIO:
gpios = <&r_pio B N flag>;
Where B originally was the pinbank label (L or M) counted from A,
with this patch it becomes (L or M) counted from its pinbank base (L).
Thus
gpios = <&r_pio 10 11 0>; /* PL11 */
becomes
gpios = <&r_pio 0 11 0>; /* PL11 */
IMO this is correct, as the binding shows the bank offset and pin offset
within the bank for the GPIO controller. But I'm worried it might be a
bit confusing.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When an IRQ is started on a GPIO line, mark this GPIO as IRQ in
the gpiolib so we can keep track of the usage centrally.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The rk3288 is the first Rockchip soc handling the drive strength on a per-pin
basis, while the older ones can set the drive-strength only for specific
pin-groups. Therefore limit setting the drive-strength to this soc for now.
Signed-off-by: Heiko Stübner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
An upcoming pinctrl function of the rk3288 differs again from everything else,
so we'll need a separate type for it.
Signed-off-by: Heiko Stübner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The rockchip pinctrl driver implements the generic pinconfig, therefore
also state this, so that the default pinconf dump functions work.
Signed-off-by: Heiko Stübner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Instead of relying on pinmux->disable(), make the gpio function an
explicit function for all pins that supports it.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Adds device tree bindings and a driver for the XUSB pad controller found
on Tegra114 and later. This is a prerequisites for PCIe, SATA and XUSB
drivers which are all currently being reviewed or pending for merge.
This is a separate branch in case it needs to be pulled into the pinctrl
tree to resolve conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABAgAGBQJTySWRAAoJEN0jrNd/PrOhIXsP/2Zfx2ctY5i9PTsu8V8tnuQ7
IO6mNKZGE9nocoi64Nq/+tBiQn+X1y0Pu5uHJt9a4FCOpNY5TsgwN3d3PCoRNbqu
1Buqjla/cgAZ+E2WkqSqvZLxlTIAIlFGxNNucBgXkn1euebsNkYWgdcxucUBqdUE
F1AgsZFK6wuZIONZIRTBWUxZwSiu5Nh0Fd6Qg6yZbMTs8mKZVesm0KHglZiAH/m9
h6htGQpfwxGqnk1O3Cm0I6dwuhMLzoVCPdnPfDx5K5mTNeOmfPcRsJ6au9S1eqM8
ZI0o+aCWiOi42UBLcCX7voriPSsTq0Ur5igmo+Gn3Rfa00aACuy3FPu8a3+453ID
nnG3zo2vLDO5MkRbCqgvW7L29Q6wtO7Xx5o608tetvCC4MXItj5OSzowp57m9OIw
PP1pYc3fgJeAbh8tHAc81tHUbV0mNYVLxN44erg3SVO168+clHVDWdTYqMFUtGs8
kPKsgJHeQKW5tKlOf919+oCaIje64vhzwOTN+L0M+TPUD8S8qkBfFEcNQkFPZ5GA
v7xyAgTHlTcwpkKRt4fdI97PfPpu47+wVu3d0Ivv/zzE5oPuQqdXMgeWzBrMUysh
nUycFAxiq9JljaBMNAaLJH+S+eX8yrI8GoOe+s+dQrVk2vFmKKvSDU5wbT4jQvxh
T3tUy/gem9p19dVcQhpU
=oUBt
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.17-xusb-padctl' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt
Merge "ARM: tegra: Add XUSB pad controller support" from Thierry Reding:
Adds device tree bindings and a driver for the XUSB pad controller found
on Tegra114 and later. This is a prerequisites for PCIe, SATA and XUSB
drivers which are all currently being reviewed or pending for merge.
This is a separate branch in case it needs to be pulled into the pinctrl
tree to resolve conflicts.
* tag 'tegra-for-3.17-xusb-padctl' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
pinctrl: Add NVIDIA Tegra XUSB pad controller support
of: Add NVIDIA Tegra XUSB pad controller binding
Signed-off-by: Olof Johansson <olof@lixom.net>
st_gpio_irqmux_handler() reads the status register to find out
which banks inside the controller have pending IRQs.
For each banks having pending IRQs, it calls the corresponding handler.
Problem is that current code restricts the number of possible banks inside the
controller to ST_GPIO_PINS_PER_BANK. This define represents the number of pins
inside a bank, so it shouldn't be used here.
On STiH407, PIO_FRONT0 controller has 10 banks, so IRQs pending in the two
last banks (PIO18 & PIO19) aren't handled.
This patch replace ST_GPIO_PINS_PER_BANK by the number of banks inside the
controller.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: <stable@vger.kernel.org> #v3.15+
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We have a bunch of Nomadik family pin control drivers, so let's
move them into their own subdirectory.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The XUSB pad controller found on NVIDIA Tegra SoCs provides several pads
that lanes can be assigned to in order to support a variety of interface
options: USB 2.0, USB 3.0, PCIe and SATA.
In addition to the pin controller used to assign lanes to pads two PHYs
are exposed to allow the bricks for PCIe and SATA to be powered up and
down by PCIe and SATA drivers.
Tested-by: Mikko Perttunen <mperttunen@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Group all pin control drivers of Samsung platform together in
a sub-directory for easy maintenance.
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch moves data allocated using regulator_register to
devm_regulator_register and does away the calls to regulator_unregister.
The sh73a0_pinmux_soc_exit function is no longer needed and is removed.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We have four Qualcomm-related pin control drivers, and now there
are drivers coming in for the PMICs on these systems, so let's
create a qcom subdirectory to hold all the Qualcomm stuff.
Acked-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch extends the range of settings configurable via pinfunc API
to cover pin value as well. This allows configuration of default values
of pins, which is useful for pins that are not supposed to be used by
any dedicated driver, but need certain board-specific setting.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
One of remaining limitations of current pinctrl-samsung driver was
the inability to parse multiple pinmux/pinconf group nodes grouped
inside a single device tree node. It made defining groups of pins for
single purpose, but with different parameters very inconvenient.
This patch implements Tegra-like support for grouping multiple pinctrl
groups inside one device tree node, by completely changing the way
pin groups and functions are parsed from device tree. The code creating
pinctrl maps from DT nodes has been borrowed from pinctrl-tegra, while
the initial creation of groups and functions has been completely
rewritten with following assumptions:
- each group consists of just one pin and does not depend on data
from device tree,
- each function is represented by a device tree child node of the
pin controller, which in turn can contain multiple child nodes
for pins that need to have different configuration values.
Device Tree bindings are fully backwards compatible. New functionality
can be used by defining a new pinctrl group consisting of several child
nodes, as on following example:
sd4_bus8: sd4-bus-width8 {
part-1 {
samsung,pins = "gpk0-3", "gpk0-4",
"gpk0-5", "gpk0-6";
samsung,pin-function = <3>;
samsung,pin-pud = <3>;
samsung,pin-drv = <3>;
};
part-2 {
samsung,pins = "gpk1-3", "gpk1-4",
"gpk1-5", "gpk1-6";
samsung,pin-function = <4>;
samsung,pin-pud = <4>;
samsung,pin-drv = <3>;
};
};
Tested on Exynos4210-Trats board and a custom Exynos4212-based one.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Cc: devicetree@vger.kernel.org
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Handling of irq_chip operations for GPIO and WKUP external interrupts
is mostly the same, with the difference being offset of registers.
However currently the driver has all the code duplicated for both EINT
types, which is undesirable, because changes in irq_chip operations have
to be done to both instances of the same code.
This patch fixes this by creating exynos_irq_chip struct that has normal
irq_chip struct embedded and contain differences between particular EINT
types, which are three register offsets. One instance of code is removed
and the new structure is used instead to fetch necessary data instead of
samsung_pin_ctrl struct used previously.
While at it, the patch removes Exynos-specific fields from
aforementioned structure to improve layering of the driver.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds .request() and .free() operations to gpio_chip of
pinctrl-samsung driver, which call pinctrl request and free helpers to
request and free pinctrl pin along with GPIO pin.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch makes the pinctrl-samsung driver configure GPIO direction on
its own, without using the pinctrl_gpio_direction_*() "helpers". The
rationale behind this change is as follows:
- pinctrl-samsung does not need translation from GPIO namespace to
pinctrl namespace to handle GPIO operations - GPIO chip and offset
therein are enough to calculate necessary offsets and bit masks in
constant time,
- the pinctrl_gpio_direction_*() functions do not do anything useful
other than translating the pin into pinctrl namespace and calling the
.gpio_set_direction() from pinmux_ops of the controller,
- the undesirable side effect of using those helpers is losing the
ability to change GPIO direction in atomic context, because they
explicitly use a mutex for synchronization,
Results of this patch are:
- fixed warnings about scheduling while atomic in code that needs to
set GPIO direction in atomic context (e.g. interrupt handler),
- reduced overhead of bitbanging drivers that use gpio_direction_*(),
e.g. i2c-gpio.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
For Baytrail, you should never set a GPIO set to direct_irq
to output mode. When direct_irq_en is set for a GPIO, it is
tied directly to an APIC internally, and making the pad output
does not make any sense. Assert a WARN() in the event this happens.
Signed-off-by: Eric Ernst <eric.ernst@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove variable that are never used
This was found using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
%d in format string used, but the type is unsigned int
This was found using a static code analysis program called cppcheck
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
%d in format string used, but the type is unsigned int
This was found using a static code analysis program called cppcheck
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove variable that are never used
This was found using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove variable that are never used
This was found using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove checking if a unsigned is less than zero
This was found using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove checking if a unsigned is less than zero
This was found using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove checking if a unsigned is less than zero
This was found using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove checking if a unsigned is less than zero
This was found using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
no .irq_set_wake API is available for pinctrl-st driver.
Add the IRQCHIP_SKIP_SET_WAKE flag to inform irq handler
not to call this API.
Signed-off-by: David Paris <david.paris@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
bcm281xx_pinctrl_probe is local to this file. Make it static.
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The A23 has a R_PIO pin controller, similar to the one found on the A31 SoC.
Add support for the pins controlled by the R_PIO controller.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The A23 uses the same pin controller as previous SoC's from Allwinner.
Add support for the pins controlled by the main PIO controller.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The PINCTRL_SUNXI configuration was kept only to deal with the introduction of
per-machine symbols and the various pintrl drivers through different tree.
Now that it's not useful anymore, we can just remove it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The A13 user manual states pins PG0/1/2 only have GPIO input and
interrupt functions. Remove the gpio_out functions for these pins.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pin-controller of the new RK3288 contains all the quirks just added in
the previous patches.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On the upcoming RK3288 SoC contain some unrouted pins in their banks. So while
for example pin8 of bank5 stays pin8 with all its settings (register offset etc),
pins 0 to 7 are not routed outside the SoC at all.
Therefore add a flag to mark these unrouted iomuxes to prevent people from using
them.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The upcoming rk3288 moves some iomux settings to the pmu register space.
Therefore add a flag for this and adapt the mux functions accordingly.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In the upcoming rk3288 SoC some iomux settings are 4bit wide instead of
the regular 2bit. Therefore add a flag to mark iomuxes as such and adapt
the mux-access as well as the offset calculation accordingly.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
An upcoming SoC introduces an interesting quirk to iomux handling making the
calculation of the iomux register-offset harder. To keep the complexity down
when getting/setting the mux, precalculate the actual register offset at
probe-time.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Upcoming Rockchip SoCs have additional quirks to handle. Currently they would
be handled by giving the bank a special compatible property. But the nature
of the new quirks would require a lot of them. Also as we want to move to the
separate dw_gpio driver in the future, these bank-definitions should be
extended at all.
Describing the bank quirks this way also enables us to deprecate the special
bank compatible string for bank0 on rk3188 and simplify the handling code.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
What the patch does:
1. Call pinmux_disable_setting ahead of pinmux_enable_setting
each time pinctrl_select_state is called
2. Remove the HW disable operation in pinmux_disable_setting function.
3. Remove the disable ops in struct pinmux_ops
4. Remove all the disable ops users in current code base.
Notes:
1. Great thanks for the suggestion from Linus, Tony Lindgren and
Stephen Warren and Everyone that shared comments on this patch.
2. The patch also includes comment fixes from Stephen Warren.
The reason why we do this:
1. To avoid duplicated calling of the enable_setting operation
without disabling operation inbetween which will let the pin
descriptor desc->mux_usecount increase monotonously.
2. The HW pin disable operation is not useful for any of the
existing platforms.
And this can be used to avoid the HW glitch after using the
item #1 modification.
In the following case, the issue can be reproduced:
1. There is a driver that need to switch pin state dynamically,
e.g. between "sleep" and "default" state
2. The pin setting configuration in a DTS node may be like this:
component a {
pinctrl-names = "default", "sleep";
pinctrl-0 = <&a_grp_setting &c_grp_setting>;
pinctrl-1 = <&b_grp_setting &c_grp_setting>;
}
The "c_grp_setting" config node is totally identical, maybe like
following one:
c_grp_setting: c_grp_setting {
pinctrl-single,pins = <GPIO48 AF6>;
}
3. When switching the pin state in the following official pinctrl
sequence:
pin = pinctrl_get();
state = pinctrl_lookup_state(wanted_state);
pinctrl_select_state(state);
pinctrl_put();
Test Result:
1. The switch is completed as expected, that is: the device's
pin configuration is changed according to the description in the
"wanted_state" group setting
2. The "desc->mux_usecount" of the corresponding pins in "c_group"
is increased without being decreased, because the "desc" is for
each physical pin while the setting is for each setting node
in the DTS.
Thus, if the "c_grp_setting" in pinctrl-0 is not disabled ahead
of enabling "c_grp_setting" in pinctrl-1, the desc->mux_usecount
will keep increasing without any chance to be decreased.
According to the comments in the original code, only the setting,
in old state but not in new state, will be "disabled" (calling
pinmux_disable_setting), which is correct logic but not intact. We
still need consider case that the setting is in both old state
and new state. We can do this in the following two ways:
1. Avoid to "enable"(calling pinmux_enable_setting) the "same pin
setting" repeatedly
2. "Disable"(calling pinmux_disable_setting) the "same pin setting",
actually two setting instances, ahead of enabling them.
Analysis:
1. The solution #2 is better because it can avoid too much
iteration.
2. If we disable all of the settings in the old state and one of
the setting(s) exist in the new state, the pins mux function
change may happen when some SoC vendors defined the
"pinctrl-single,function-off"
in their DTS file.
old_setting => disabled_setting => new_setting.
3. In the pinmux framework, when a pin state is switched, the
setting in the old state should be marked as "disabled".
Conclusion:
1. To Remove the HW disabling operation to above the glitch mentioned
above.
2. Handle the issue mentioned above by disabling all of the settings
in old state and then enable the all of the settings in new state.
Signed-off-by: Fan Wu <fwu@marvell.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pads for PB0-PB3, PC0-PC4, PE26-PE31 and PF24-PF31 does not exist on
the i.MX27 SOC. There is no reason to define them, the presence of
such definitions in the DTS files is a bug.
This patch removes these nonexistent pad definitions.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
struct imx27_pinctrl_private is not used in the driver.
Remove this definition.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When mapping the interrupts, the gpio_to_irq function did not consider
the bank number of the gpio pin in question, only the offset or the
interrupt number in the bank. As a result, requests for interrupts in
the later banks get mapped to the first bank.
This issue was discovered while enabling mmc on the new sun8i platform.
The tablet I have uses a pin/interrupt from the second bank to do mmc
card detection. Tested on this very device with register inspection and
actual mmc card insertion/removal.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some drivers use disable_irq / enable_irq and do the work
clearing the source in another thread instead of using a threaded
interrupt handler.
The irqchip used not having irq_disable and irq_enable
callbacks in this case, will lead to unnecessary spurious
interrupts:
On a disable_irq in a chip without a handler for this, the irq
core will remember the disable, but not actually call into the
irqchip. With a level triggered interrupt (where the source has
not been cleared) this will lead to an immediate retrigger, at
which point the irq-core will mask the irq. So having an
irq_disable callback in the irqchip will save us the interrupt
firing a 2nd time for nothing.
Drivers using disable / enable_irq like this, will call
enable_irq when they finally have cleared the interrupt source,
without an enable_irq callback, this will turn into an unmask,
at which point the irq will trigger immediately because when it
was originally acked the level was still high, so the ack was
a nop.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
For level triggered gpio interrupts we need to use handle_fasteoi_irq,
like we do with the irq-sunxi-nmi driver. This is necessary to give threaded
interrupt handlers a chance to actuall clear the source of the interrupt
(which may involve sleeping waiting for i2c / spi / mmc transfers), before
acknowledging the interrupt.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
With level triggered interrupt mask / unmask will get called for each
interrupt, doing the somewhat expensive mux setting on each unmask thus is
not a good idea. Instead add a request_resources callback and do it there.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The sunxi pinctrl irq chip driver does not support wakeup at the
moment. Adding IRQCHIP_SKIP_SET_WAKE lets the irqs work with drivers
using wakeup.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These symbols are supposed to be selected by the drivers actually needing
them. The only situation where it would make sense to enable them without a
driver selecting them is when an out-of-tree pinctrl driver is used or
for compile testing.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We are returning success here because PTR_ERR(NULL) is zero. We should
be returning -ENODEV.
Fixes: 3de68d331c ('pinctrl: berlin: add the core pinctrl driver for Marvell Berlin SoCs')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This switches the SPEAr PLGPIO driver over to using the irqchip
helpers.
As part of this effort, also get rid of the strange irq_base
calculation and failure to use d->hwirq for obtaining a local
irqchip offset.
Cc: Viresh Kumar <viresh.linux@gmail.com>
Cc: Shiraz Hashim <shiraz.linux.kernel@gmail.com>
Cc: spear-devel@list.st.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The A23 and A31 support multiple interrupt banks. Support it by adding a linear
domain covering all the banks. It's trickier than it should because there's an
interrupt per bank, so we have multiple interrupts using the same domain.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The primary pinctrl device has 4 interrupt banks. As usual, to be able to
generate interrupts, the pins supporting it need to be muxed to a special
function. Declare these functions in the pins array.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Declare in the description structure associated to the compatible the number of
interrupt banks the device has. For now, we're not doing anything with it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The A31 and A23, unlike the other Allwinner SoCs, have several interrupts banks
and parent interrupts, while the other only have up to 32 interrupts in a
single bank and a single parent interrupt.
Start supporting it by introducing a function macro to declare irq functions
and their banks.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If irq_mask_ack is not defined, mask_ack_irq will call irq_mask and then
irq_ack. In order to avoid code duplication, between irq_mask_ack and irq_mask,
just declare irq_ack.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
kzalloc can fail. Add a null check to avoid null pointer
dereference error while accessing the pointer later.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
development cycle:
- Antoine Tenart made the get_group_pins() vtable entry
optional.
- Antoine also provides an entirely new driver for the
Marvell Berlin SoC. This is unrelated to the existing
MVEBU hardware driver and warrants its own separate
driver.
- Reflected from the GPIO subsystem there is a number of
refactorings to make pin control drivers with gpiochips
use the new gpiolib irqchip helpers. The following
drivers were converted to use the new infrastructure:
- ST Microelectronics STiH416 and friends
- The Atmel AT91
- The CSR SiRF (Prima2)
- The Qualcomm MSM series
- Massive improvements in the Qualcomm MSM driver from
Bjorn Andersson, Andy Gross and Kumar Gala. Among those
new support for the IPQ8064 and MSM8x74 SoC variants.
- Support for the Freescale i.MX6 SoloX SoC variant.
- Massive improvements in the Allwinner sunxi driver from
Boris Brezillon, Maxime Ripard and Chen-Yu Tsai.
- Renesas PFC updates from Laurent Pinchart, Kuninori
Morimoto, Wolfram Sang and Magnus Damm.
- Cleanups and refactorings of the nVidia Tegra driver from
Stepgen Warren.
- The Exynos driver now supports the Exynos3250 SoC.
- Intel BayTrail updates from Jin Yao, Mika Westerberg.
- The MVEBU driver now supports the Orion5x SoC
variants, which is part of the effort of getting rid of
the old Marvell kludges in arch/arm/mach-orion5x
- Rockchip driver updates from Heiko Stuebner.
- A ton of cleanups and janitorial patches from Axel Lin.
- Some minor fixes and improvements here and there.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJTjXDAAAoJEEEQszewGV1z8zsP/i+7o5sU+rm3ZwfpCyuVih7E
90nHTMzV2Se+8gX4D0jLZUYkxMQn9pkqG616IyT5kP5sx9co8raoAUC1Qmv6b7rI
kIlfCaDvjPzEWgH9KZNjMP8P0rqdj8TelDRSZ0EPzHdfyUwxFmLRnFo7ywguPCG2
SOM1uo7XhjXmphoUP7ZZWs3doflYxBAL3ZdK77QQcLEQjlNxSz/vbls6ldkKie7C
XF7DKvGqphB8GdGKkdFvyhjQNy26rBanZRy94yU53Ak5zc0mTtmO+WEjiByAW1m7
Fy6AVdZZhl6BLxzn9rUzsKdrWzaWzUkQNilhEO1u7OfZtNQbuYWcv7GJ7h37lIzI
P0jegOy+7d4JxPyROphtJXx6AwV1pFFimMnWS4rHwUdjwMBVRnlOKQW/G7ulEBsn
wD5MhD76nHySKtjYquI+iVHbmE06hG8iDUUxFm2saVG8O7Siw+E2aCXPLm9+Lp5R
fBNuj8lnTy8/F6sHyPs8Bw6u8Ra5uSmRhV4j3B/jZG8pAksqUK6xOmjdVdE7JmoH
qIZxuQhqrAhjmGkAg/ys5SUuMMbegxTI2f+rDy7rpWonbVOtaItMpgbYwyiQpIR4
BDmlwZi5BNupiEW7Yzp6utWYIyYA0ntuMGpnqnPBDBCn5jZOCUTMjZXAPCDK5dEN
Ktyu+5jCBZgpqS+KgTXl
=wGE5
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v3.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl into next
Pull pin control changes from Linus Walleij:
"This is the bulk of pin control changes for the v3.16 development
cycle:
- Antoine Tenart made the get_group_pins() vtable entry optional.
- Antoine also provides an entirely new driver for the Marvell Berlin
SoC. This is unrelated to the existing MVEBU hardware driver and
warrants its own separate driver.
- reflected from the GPIO subsystem there is a number of refactorings
to make pin control drivers with gpiochips use the new gpiolib
irqchip helpers. The following drivers were converted to use the
new infrastructure:
* ST Microelectronics STiH416 and friends
* The Atmel AT91
* The CSR SiRF (Prima2)
* The Qualcomm MSM series
- massive improvements in the Qualcomm MSM driver from Bjorn
Andersson, Andy Gross and Kumar Gala. Among those new support for
the IPQ8064 and MSM8x74 SoC variants.
- support for the Freescale i.MX6 SoloX SoC variant.
- massive improvements in the Allwinner sunxi driver from Boris
Brezillon, Maxime Ripard and Chen-Yu Tsai.
- Renesas PFC updates from Laurent Pinchart, Kuninori Morimoto,
Wolfram Sang and Magnus Damm.
- Cleanups and refactorings of the nVidia Tegra driver from Stepgen
Warren.
- the Exynos driver now supports the Exynos3250 SoC.
- Intel BayTrail updates from Jin Yao, Mika Westerberg.
- the MVEBU driver now supports the Orion5x SoC variants, which is
part of the effort of getting rid of the old Marvell kludges in
arch/arm/mach-orion5x
- Rockchip driver updates from Heiko Stuebner.
- a ton of cleanups and janitorial patches from Axel Lin.
- some minor fixes and improvements here and there"
* tag 'pinctrl-v3.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (93 commits)
pinctrl: sirf: fix a bad conflict resolution
pinctrl: msm: Add more MSM8X74 pin definitions
pinctrl: qcom: ipq8064: Fix naming convention
pinctrl: msm: Add missing sdc1 and sdc3 groups
pinctrl: sirf: switch to using allocated state container
pinctrl: Enable "power-source" to be extracted from DT files
pinctrl: sunxi: create irq/pin mapping during init
pinctrl: pinconf-generic: Use kmemdup instead of kmalloc + memcpy
pinctrl: berlin: Use devm_ioremap_resource()
pinctrl: sirf: fix typo for GPIO bank number
pinctrl: sunxi: depend on RESET_CONTROLLER
pinctrl: sunxi: fix pin numbers passed to register offset helpers
pinctrl: add pinctrl driver for imx6sx
pinctrl/at91: Fix lockup when IRQ on PIOC and PIOD occurs
pinctrl: msm: switch to using generic GPIO irqchip helpers
pinctrl: sunxi: Fix multiple registration issue
pinctrl: sunxi: Fix recursive dependency
pinctrl: berlin: add the BG2CD pinctrl driver
pinctrl: berlin: add the BG2 pinctrl driver
pinctrl: berlin: add the BG2Q pinctrl driver
...
Commit 294d1351ff
"pinctrl: sirf: switch to using allocated state container"
caused a build conflict due to a bad conflict resolution
when cherry-picking the patch. Fix it up.
Cc: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Drop underscore in spdif_groups to match all other groups.
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Reviewed-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This rewrites the SIRF pinctrl driver to allocate a state container
for the GPIO chip, just as is done for the pin controller, and
use the gpiochip_add_pin_range() to add the range from the gpiochip
side rather than adding the range from the pinctrl side.
All resulting changes are done in order to pass around a state
container rather than refer to a static global object.
Acked-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add "power-source" property to generic options used for DT parsing files.
This enables drivers, which use generic pin configurations, to get the
value passed to this property.
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The irq/pin mapping is used to lookup the pin to mux to the irq
function when the irq is enabled. It is created when gpio_to_irq
is called. Creating the mapping during init allows us to map the
interrupts directly from the device tree.
Originally the IRQ to pin mapping was created when gpio_to_irq
was called with a GPIO handle. The mapping in turn is used to mux
the pin into EINT mode.
If the mapping is created during gpio_to_irq, we can't use the
interrupts directly, i.e. through the DT with "interrupts = <&pio A 4>".
Instead we'd have to use "gpios = <&pio A B>", then pass the gpio
through to gpio_to_irq.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This issue was reported by coccicheck using the semantic patch
at scripts/coccinelle/api/memdup.cocci
Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use devm_ioremap_resource() because devm_request_and_ioremap() is
obsoleted by devm_ioremap_resource().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The patch 7420d2d09b: "pinctrl: sirf: switch driver to use gpiolib
irqchip helpers" from Apr 15, 2014, leads to the following static
checker warning:
drivers/pinctrl/sirf/pinctrl-sirf.c:578 sirfsoc_gpio_handle_irq()
warn: buffer overflow 'sgpio_chip.sgpio_bank' 5 <= 31
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The A31 R_PIO driver depends on the reset framework in a mandatory way. Express
this by adding a depends on the reset framework in Kconfig
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pin numbers passed to sunxi_*_reg helpers to get the correct
registers should be the pin offset for the PIO block, not the
absolute number we use that is based on the alphanumeric labels
Allwinner uses.
This patch subtracts .pin_base from the pin number passed to these
functions, so the driver accesses the correct registers.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
With commit 80cc3732 (pinctrl/at91: convert driver to use gpiolib irqchip)
gpiochip_set_chained_irqchip is called for PIOC, PIOD and PIOE. The
associated GPIO chip for the IRQ chip is overwritten each time, because
they share the same hard IRQ line.
Thus if an IRQ occurs on PIOC or PIOD, gpio_irq_handler will only check on
PIOE (the assigned GPIO chip) where no event occured. Thus the IRQ will
not be cleared, retriggering the ISR.
Fix that (like done before) by only set the PIOC GPIO chip to the IRQ chip
and walk the list in the irq handler.
Signed-off-by: Alexander Stein <alexanders83@web.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This switches the Qualcomm MSM pin control driver over to using
the generic GPIO irqchip helpers.
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Josh Cartwright <joshc@codeaurora.org>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When the support for the PRCM muxer on the A31 has been added, the global
static pinctl_desc definition has been left as is. Unfortunately, this
structure is used to register the pinctrl device, and prior to this
registration, we set the name and pins field.
Since this structure is shared across instances, that means that the latest
registered pinctrl device wins in setting the name, pins and pins numbers,
which is not really a good thing.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix the following configuration error:
drivers/pinctrl/sunxi/Kconfig:3:error: recursive dependency detected!
drivers/pinctrl/sunxi/Kconfig:3: symbol PINCTRL_SUNXI is selected by PINCTRL_SUN4I_A10
drivers/pinctrl/sunxi/Kconfig:9: symbol PINCTRL_SUN4I_A10 default value contains PINCTRL_SUNXI
Add a new intermedia PINCTRL_SUNXI_COMMON, that superseeds the PINCTRL_SUNXI
one.
We still need to keep PINCTRL_SUNXI at the moment in order to preserve
bisectability. Indeed, during that merge window, we also introduced the
MACH_SUN* symbols. Since it's going through different trees, we can't rely on
the fact that the options will be there, while ARCH_SUNXI still select
PINCTRL_SUNXI.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the pin-controller driver for the Berlin BG2Q SoC, with definition
of its groups and functions. Pin control registers are part of chip/
system control registers, which will be represented by a single node.
Until a proper driver for the chip/system control is available,
register the corresponding regmap in pinctrl driver probe.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the pin-controller driver for the Berlin BG2 SoC, with definition
of its groups and functions. Pin control registers are part of chip/
system control registers, which will be represented by a single node.
Until a proper driver for the chip/system control is available,
register the corresponding regmap in pinctrl driver probe.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the pin-controller driver for the Berlin BG2Q SoC, with definition
of its groups and functions. Pin control registers are part of chip/
system control registers, which will be represented by a single node.
Until a proper driver for the chip/system control is available,
register the corresponding regmap in pinctrl driver probe.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Marvell Berlin boards have a group based pinmuxing mechanism. This
adds the core driver support. We actually do not need any information
about the pins here and only have the definition of the groups.
Let's take the example of the uart0 pinmuxing on the BG2Q. Balls BK4 and
BH6 are muxed to respectively UART0 RX and TX if the group GSM12 is set
to mode 0:
Group Modes Offset Base Offset LSB Bit Width
GSM12 3 sm_base 0x40 0x10 0x2
Ball Group Mode 0 Mode 1 Mode 2
BK4 GSM12 UART0_RX IrDA0_RX GPIO9
BH6 GSM12 UART0_TX IrDA0_TX GPIO10
So in order to configure BK4 -> UART0_TX and BH6 -> UART0_RX, we need
to set (sm_base + 0x40 + 0x10) &= ff3fffff.
As pin control registers are part of either chip control or system
control registers, that deal with a bunch of other functions we rely
on a regmap instead of exclusively remapping any resources.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In case of resolving power management or similar issues it might be useful
to have these properties included in the debugfs output.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If chip->to_irq is NULL ACPI GPIO helpers don't register GPIO event
handlers thus preventing any ACPI GPIO triggered events. Solve this by
calling gpiochip_add() after we have set up drivers chip->to_irq hook.
Signed-off-by: Jin Yao <yao.jin@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now that the x86 dynamic IRQ allocation problem has been resolved with
commmit 62a08ae2a5 (genirq: x86: Ensure that dynamic irq allocation does
not conflict), we can add back Baytrail-T ACPI ID to the pinctrl driver.
This makes the driver to work on Asus T100 where it is needed for several
things like ACPI GPIO events and SD card detection.
References: https://bugzilla.kernel.org/show_bug.cgi?id=68291
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Jin Yao <yao.jin@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In the multiplatform kernel case the IRQs associated with the PFC GPIOs
are specified through DT. The pinmux_irq irq field is thus ignored by
the code, and doesn't need to be set.
This will allow removing the mach/irq.h include from pfc-*.c files that
was required for the irq_pin() macro used to initialize the irq field.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Enable the freshly introduced Kconfig options whenever their matching
architecture is enabled.
Since the Kconfig symbols for these machines are going through a different
tree, keep PINCTRL_SUNXI around for the moment to avoid breaking the defconfig.
It should be removed eventually.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Current code only touches the direction register when setting direction
to output, which breaks logic like
echo high > /sys/class/gpio/gpio0/direction
which is expected to also set the value. This patch also adds a call
to update the value register when setting direction to output.
Signed-off-by: Alexey Charkov <alchark@gmail.com>
Acked-by: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This allows the basic registers of the general register files to be supplied
by a syscon instead of being mapped locally.
The GRF registers contain a lot more than pinctrl functions like dma, usb-phy
and general soc control and status registers, intermixed with the iomux, pull
and drive-strength registers.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Max Schwarz <max.schwarz@online.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When the pmu registers are supplied through a syscon regmap we do not need
to map the registers ourself.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Max Schwarz <max.schwarz@online.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently the pmu registers containing pin pull settings on the rk3188 are mapped
locally when bank0 is instantiated. Add an alternative that can resolve the pmu
from a syscon phandle.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Max Schwarz <max.schwarz@online.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Convert rockchip_get_bank_data to use the struct rockchip_pinctrl because
later on we need to check a value from it when registering the gpio banks.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Max Schwarz <max.schwarz@online.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This allows us to use syscons in the future.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Max Schwarz <max.schwarz@online.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Deprecate secondary register area for rk3188 pulls. Instead use big enough
initial mapping of grf registers to catch all.
The now deprecated register is still supported though.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Max Schwarz <max.schwarz@online.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This serie of patch:
- Moves the Allwinner pinctrl driver to a folder of its own
- removes the sunxi-pinctrl-pins header, and split the driver into a core
one, with all the logic, and smaller drivers, one for each SoC, that
declare the pins, and will provide to the core the set of pins.
- And does a few cleanups here and there.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=nUR7
-----END PGP SIGNATURE-----
Merge tag 'sunxi-pinctrl-for-3.16' of https://github.com/mripard/linux into devel
Pinctrl cleanup and reworks for 3.16
This serie of patch:
- Moves the Allwinner pinctrl driver to a folder of its own
- removes the sunxi-pinctrl-pins header, and split the driver into a core
one, with all the logic, and smaller drivers, one for each SoC, that
declare the pins, and will provide to the core the set of pins.
- And does a few cleanups here and there.
The way that reset is handled right now is that it is made optional for every
pinctrl driver, while actually, it isn't used at all for the main pin
controllers so far, and while it's mandatory for the A31's secondary pin
controller.
Move the reset functions out of the core and in the driver, where they can be
made mandatory.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add one Kconfig option for each driver. This will allow to better control which
driver is enabled, instead of having either all or nothing.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Move the pin description to a driver specific to be.
This is the final step toward retiring pinctrl-sunxi-pins.h that used to define
all the pins for all the Allwinner SoCs in a single header, that would have in
turn result in having these structures in the final binary as many times as the
header was included.
We can finally remove that header, and remove all the driver part of the
pinctrl-sunxi core.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Move the pin description to a driver specific to be. This is one more step
toward retiring pinctrl-sunxi-pins.h that used to define all the pins for all
the Allwinner SoCs in a single header, that would have in turn result in having
these structures in the final binary as many times as the header was included.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Move the pin description to a driver specific to be. This is one more step
toward retiring pinctrl-sunxi-pins.h that used to define all the pins for all
the Allwinner SoCs in a single header, that would have in turn result in having
these structures in the final binary as many times as the header was included.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Move the pin description to a driver specific to be. This is one more step
toward retiring pinctrl-sunxi-pins.h that used to define all the pins for all
the Allwinner SoCs in a single header, that would have in turn result in having
these structures in the final binary as many times as the header was included.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Move the pin description to a driver specific to be. This is one more step
toward retiring pinctrl-sunxi-pins.h that used to define all the pins for all
the Allwinner SoCs in a single header, that would have in turn result in having
these structures in the final binary as many times as the header was included.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Move the pin description to a driver specific to be. This is one more step
toward retiring pinctrl-sunxi-pins.h that used to define all the pins for all
the Allwinner SoCs in a single header, that would have in turn result in having
these structures in the final binary as many times as the header was included.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This will allow to have multiple drivers using the same core code, and
eventually, retire pinctrl-sunxi-pins.h
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The previous code was calling of_iomap, which doesn't do any resource
management, and doesn't call request_mem_region either. Use
devm_ioremap_resource that do both.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
We previously had an evergrowing (and exhaustive) list of the pins that could
be used on any Allwinner SoCs. These defines were then used by each pinctrl
driver to declare the list of functions for this pin. Since it's pretty much
all boilerplate, we can remove it just by a single macro.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The pins description structure were declared as const, but the of_device_id
data magic was losing it silently.
Make sure we have it on both sides.
And now that we're using const, we can also remove the useless cast in probe.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This commit extends the pinctrl mvebu logic with a new driver to cover
Orion5x SoC. It supports the definitions for the 5181l, 5182 and 5281
variants of Orion5x, which are the three ones supported by the old
style MPP code in arch/arm/mach-orion5x/.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In some cases it is nice to be able to simply control a gpio output
via the PIN_CONFIG_OUTPUT option without having a driver control it.
Thus add support for it to the rockchip pinctrl driver.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Till now pinconf_get only set the argument value into the config parameter
effectively removing the actual config param value. As other pinctrl drivers
do, it might be nicer to keep the config param intact.
Therefore construct a real pinconfig value from param and arg in pinconf_get
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This switches the SiRF pinctrl driver over to using the gpiolib
irqchip helpers simplifying some of the code.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
all gpio banks are in one chip, that makes software clean in mapping
irq and gpio.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The sirfsoc_irqchip_to_bank() is obviously misnamed, as it is
not converting an irqchip to a bank but converts a gpiochip
to a bank so rename it sirfsoc_gpiochip_to_bank().
Acked-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is a missing 0 entry from the MOD_SEL3 table.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The extra entry in the table makes SCIFA0_B, and all
peripherals after it, fail.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds pinctrl definitions for the GPIO pins of the TLMM v2 block in the
Qualcomm IPQ8064 platform.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since we set up device wake-up interrupts as pinctrl-single
interrupts, we now must use the standard request_irq and
related functions to manage them.
If the pin interrupts are enabled for some pins at boot,
the wake-up events can show up as constantly pending
at least on omaps and will hang the system unless the related
device driver clears the event at the device.
To fix this, let's clear the interrupt flags during init,
and print out a warning so the board maintainers can update
their drivers to do proper request_irq for the driver specific
wake-up events.
Cc: Haojian Zhuang <haojian.zhuang@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds driver data (bank list and EINT layout) for Exynos3250
to pinctrl-exynos driver. Exynos3250 includes 158 multi-functional input/output
ports. There are 23 general port groups.
Changes from v1:
- Add signed-off of sender
- Post only separated patch for pinctrl from following patchset(v1)
: https://lkml.org/lkml/2014/4/10/286
Cc: Thomas Abraham <thomas.abraham@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This converts the AT91 pin control driver to register its
chained irq handler and irqchip using the helpers in the
gpiolib core.
Signed-off-by: Alexander Stein <alexanders83@web.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The AS3722_GPIO_INV bit will always be blindly overwritten by
as3722_pinctrl_gpio_set_direction() and will be ignored when
setting the value of the GPIO in as3722_gpio_set() since the
enable_gpio_invert flag is never set. This will cause an
initially inverted GPIO to toggle when requested as an output,
which could be problematic if, for example, the GPIO controls
a critical regulator.
Instead of setting up the enable_gpio_invert flag, just leave
the invert bit alone and check it before setting the GPIO value.
Cc: <stable@vger.kernel.org> # v3.14+
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The kerneldoc for struct tegra_pingroup didn't describe all of the fields
in the struct. Add some extra kerneldoc to fix that.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When an attempt is made to configure an unsupported option on a pin,
print the DT property name of that option, so it's easier to debug
what the problem is.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The range of npins and function ID values is small enough to fit into a
u8. Use this type rather than unsigned to shrink the pinmux data tables.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The fsafe value in the pingroup data tables is only used to implement
tegra_pinctrl_disable(). The only reason this function is called is when
dynamically switching between pinmux states, i.e. when disabling the old
state before programming the new state. It's simpler to have the new
target state define the expected value of each pin (and all current DTs
do that). This also gives more flexibility, since it allows individual
boards explicit control over the "inactive" mux function for each pin,
rather than requiring it to be an SoC-specific value. Assuming this, we
can get rid of the fsafe value from the driver completely, thus saving
some more space in the driver tables.
While re-writing the content of tegra124_pingroups[], fix the indentation
to use a TAB instead of spaces.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
