1) Old code was hard to maintain, due to complex lock chains.
(We probably will be able to remove some kfree_rcu() in callers)
2) Using a single timer to update all estimators does not scale.
3) Code was buggy on 32bit kernel (WRITE_ONCE() on 64bit quantity
is not supposed to work well)
In this rewrite :
- I removed the RB tree that had to be scanned in
gen_estimator_active(). qdisc dumps should be much faster.
- Each estimator has its own timer.
- Estimations are maintained in net_rate_estimator structure,
instead of dirtying the qdisc. Minor, but part of the simplification.
- Reading the estimator uses RCU and a seqcount to provide proper
support for 32bit kernels.
- We reduce memory need when estimators are not used, since
we store a pointer, instead of the bytes/packets counters.
- xt_rateest_mt() no longer has to grab a spinlock.
(In the future, xt_rateest_tg() could be switched to per cpu counters)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check if the returned device from tcf_exts_get_dev function supports tc
offload and in case the rule can't be offloaded, set the filter hw_dev
parameter to the original device given by the user.
The filter hw_device parameter should always be set by fl_hw_replace_filter
function, since this pointer is used by dump stats and destroy
filter for each flower rule (offloaded or not).
Fixes: 7091d8c705 ('net/sched: cls_flower: Add offload support using egress Hardware device')
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Reported-by: Simon Horman <horms@verge.net.au>
Tested-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Made kernel accept IPv6 routes with IPv4-mapped address as next-hop.
It is possible to configure IP interfaces with IPv4-mapped addresses, and
one can add IPv6 routes for IPv4-mapped destinations/prefixes, yet prior
to this fix the kernel returned an EINVAL when attempting to add an IPv6
route with an IPv4-mapped address as a nexthop/gateway.
RFC 4798 (a proposed standard RFC) uses IPv4-mapped addresses as nexthops,
thus in order to support that type of address configuration the kernel
needs to allow IPv4-mapped addresses as nexthops.
Signed-off-by: Erik Nordmark <nordmark@arista.com>
Signed-off-by: Bob Gilligan <gilligan@arista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The check of the return value of sock_register() is ineffective.
"if(!err)" seems to be a typo. It is better to propagate the error code
to the callers of caif_sktinit_module(). This patch removes the check
statment and directly returns the result of sock_register().
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=188751
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
copy_from_iter_full(), copy_from_iter_full_nocache() and
csum_and_copy_from_iter_full() - counterparts of copy_from_iter()
et.al., advancing iterator only in case of successful full copy
and returning whether it had been successful or not.
Convert some obvious users. *NOTE* - do not blindly assume that
something is a good candidate for those unless you are sure that
not advancing iov_iter in failure case is the right thing in
this case. Anything that does short read/short write kind of
stuff (or is in a loop, etc.) is unlikely to be a good one.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Johan Hedberg says:
====================
pull request: bluetooth-next 2016-12-03
Here's a set of Bluetooth & 802.15.4 patches for net-next (i.e. 4.10
kernel):
- Fix for a potential NULL deref in the ieee802154 netlink code
- Fix for the ED values of the at86rf2xx driver
- Documentation updates to ieee802154
- Cleanups to u8 vs __u8 usage
- Timer API usage cleanups in HCI drivers
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Prior to commit c0371da604 ("put iov_iter into msghdr") in v3.19, there
was no check that the iovec contained enough bytes for an ICMP header,
and the read loop would walk across neighboring stack contents. Since the
iov_iter conversion, bad arguments are noticed, but the returned error is
EFAULT. Returning EINVAL is a clearer error and also solves the problem
prior to v3.19.
This was found using trinity with KASAN on v3.18:
BUG: KASAN: stack-out-of-bounds in memcpy_fromiovec+0x60/0x114 at addr ffffffc071077da0
Read of size 8 by task trinity-c2/9623
page:ffffffbe034b9a08 count:0 mapcount:0 mapping: (null) index:0x0
flags: 0x0()
page dumped because: kasan: bad access detected
CPU: 0 PID: 9623 Comm: trinity-c2 Tainted: G BU 3.18.0-dirty #15
Hardware name: Google Tegra210 Smaug Rev 1,3+ (DT)
Call trace:
[<ffffffc000209c98>] dump_backtrace+0x0/0x1ac arch/arm64/kernel/traps.c:90
[<ffffffc000209e54>] show_stack+0x10/0x1c arch/arm64/kernel/traps.c:171
[< inline >] __dump_stack lib/dump_stack.c:15
[<ffffffc000f18dc4>] dump_stack+0x7c/0xd0 lib/dump_stack.c:50
[< inline >] print_address_description mm/kasan/report.c:147
[< inline >] kasan_report_error mm/kasan/report.c:236
[<ffffffc000373dcc>] kasan_report+0x380/0x4b8 mm/kasan/report.c:259
[< inline >] check_memory_region mm/kasan/kasan.c:264
[<ffffffc00037352c>] __asan_load8+0x20/0x70 mm/kasan/kasan.c:507
[<ffffffc0005b9624>] memcpy_fromiovec+0x5c/0x114 lib/iovec.c:15
[< inline >] memcpy_from_msg include/linux/skbuff.h:2667
[<ffffffc000ddeba0>] ping_common_sendmsg+0x50/0x108 net/ipv4/ping.c:674
[<ffffffc000dded30>] ping_v4_sendmsg+0xd8/0x698 net/ipv4/ping.c:714
[<ffffffc000dc91dc>] inet_sendmsg+0xe0/0x12c net/ipv4/af_inet.c:749
[< inline >] __sock_sendmsg_nosec net/socket.c:624
[< inline >] __sock_sendmsg net/socket.c:632
[<ffffffc000cab61c>] sock_sendmsg+0x124/0x164 net/socket.c:643
[< inline >] SYSC_sendto net/socket.c:1797
[<ffffffc000cad270>] SyS_sendto+0x178/0x1d8 net/socket.c:1761
CVE-2016-8399
Reported-by: Qidan He <i@flanker017.me>
Fixes: c319b4d76b ("net: ipv4: add IPPROTO_ICMP socket kind")
Cc: stable@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
tsq_flags being in the same cache line than sk_wmem_alloc
makes a lot of sense. Both fields are changed from tcp_wfree()
and more generally by various TSQ related functions.
Prior patch made room in struct sock and added sk_tsq_flags,
this patch deletes tsq_flags from struct tcp_sock.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding a likely() in tcp_mtu_probe() moves its code which used to
be inlined in front of tcp_write_xmit()
We still have a cache line miss to access icsk->icsk_mtup.enabled,
we will probably have to reorganize fields to help data locality.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Always allow the two first skbs in write queue to be sent,
regardless of sk_wmem_alloc/sk_pacing_rate values.
This helps a lot in situations where TX completions are delayed either
because of driver latencies or softirq latencies.
Test is done with no cache line misses.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under high load, tcp_wfree() has an atomic operation trying
to schedule a tasklet over and over.
We can schedule it only if our per cpu list was empty.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under high stress, I've seen tcp_tasklet_func() consuming
~700 usec, handling ~150 tcp sockets.
By setting TCP_TSQ_DEFERRED in tcp_wfree(), we give a chance
for other cpus/threads entering tcp_write_xmit() to grab it,
allowing tcp_tasklet_func() to skip sockets that already did
an xmit cycle.
In the future, we might give to ACK processing an increased
budget to reduce even more tcp_tasklet_func() amount of work.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of atomically clear TSQ_THROTTLED and atomically set TSQ_QUEUED
bits, use one cmpxchg() to perform a single locked operation.
Since the following patch will also set TCP_TSQ_DEFERRED here,
this cmpxchg() will make this addition free.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a cleanup, to ease code review of following patches.
Old 'enum tsq_flags' is renamed, and a new enumeration is added
with the flags used in cmpxchg() operations as opposed to
single bit operations.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Function br_sysfs_addbr() does not set error code when the call
kobject_create_and_add() returns a NULL pointer. It may be better to
return "-ENOMEM" when kobject_create_and_add() fails.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=188781
Signed-off-by: Pan Bian <bianpan2016@163.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding space after switch keyword before open
parenthesis for readability purpose.
This patch fixes the checkpatch.pl warning:
space required before the open parenthesis '('
Signed-off-by: Suraj Deshmukh <surajssd009005@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It has been reported that update_suffix can be expensive when it is called
on a large node in which most of the suffix lengths are the same. The time
required to add 200K entries had increased from around 3 seconds to almost
49 seconds.
In order to address this we need to move the code for updating the suffix
out of resize and instead just have it handled in the cases where we are
pushing a node that increases the suffix length, or will decrease the
suffix length.
Fixes: 5405afd1a3 ("fib_trie: Add tracking value for suffix length")
Reported-by: Robert Shearman <rshearma@brocade.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Reviewed-by: Robert Shearman <rshearma@brocade.com>
Tested-by: Robert Shearman <rshearma@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It wasn't necessary to pass a leaf in when doing the suffix updates so just
drop it. Instead just pass the suffix and work with that.
Since we dropped the leaf there is no need to include that in the name so
the names are updated to node_push_suffix and node_pull_suffix.
Finally I noticed that the logic for pulling the suffix length back
actually had some issues. Specifically it would stop prematurely if there
was a longer suffix, but it was not as long as the original suffix. I
updated the code to address that in node_pull_suffix.
Fixes: 5405afd1a3 ("fib_trie: Add tracking value for suffix length")
Suggested-by: Robert Shearman <rshearma@brocade.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Reviewed-by: Robert Shearman <rshearma@brocade.com>
Tested-by: Robert Shearman <rshearma@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This switch (default on) can be used to disable automatic registration
of connection tracking functionality in newly created network
namespaces.
This means that when net namespace goes down (or the tracker protocol
module is unloaded) we *might* have to unregister the hooks.
We can either add another per-netns variable that tells if
the hooks got registered by default, or, alternatively, just call
the protocol _put() function and have the callee deal with a possible
'extra' put() operation that doesn't pair with a get() one.
This uses the latter approach, i.e. a put() without a get has no effect.
Conntrack is still enabled automatically regardless of the new sysctl
setting if the new net namespace requires connection tracking, e.g. when
NAT rules are created.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This makes use of nf_ct_netns_get/put added in previous patch.
We add get/put functions to nf_conntrack_l3proto structure, ipv4 and ipv6
then implement use-count to track how many users (nft or xtables modules)
have a dependency on ipv4 and/or ipv6 connection tracking functionality.
When count reaches zero, the hooks are unregistered.
This delays activation of connection tracking inside a namespace until
stateful firewall rule or nat rule gets added.
This patch breaks backwards compatibility in the sense that connection
tracking won't be active anymore when the protocol tracker module is
loaded. This breaks e.g. setups that ctnetlink for flow accounting and
the like, without any '-m conntrack' packet filter rules.
Followup patch restores old behavour and makes new delayed scheme
optional via sysctl.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
so that conntrack core will add the needed hooks in this namespace.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
MASQUERADE, S/DNAT and REDIRECT already call functions that depend on the
conntrack module.
However, since the conntrack hooks are now registered in a lazy fashion
(i.e., only when needed) a symbol reference is not enough.
Thus, when something is added to a nat table, make sure that it will see
packets by calling nf_ct_netns_get() which will register the conntrack
hooks in the current netns.
An alternative would be to add these dependencies to the NAT table.
However, that has problems when using non-modular builds -- we might
register e.g. ipv6 conntrack before its initcall has run, leading to NULL
deref crashes since its per-netns storage has not yet been allocated.
Adding the dependency in the modules instead has the advantage that nat
table also does not register its hooks until rules are added.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
currently aliased to try_module_get/_put.
Will be changed in next patch when we add functions to make use of ->net
argument to store usercount per l3proto tracker.
This is needed to avoid registering the conntrack hooks in all netns and
later only enable connection tracking in those that need conntrack.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
since adf0516845 ("netfilter: remove ip_conntrack* sysctl compat code")
the only user (ipv4 tracker) sets this to an empty stub function.
After this change nf_ct_l3proto_pernet_register() is also empty,
but this will change in a followup patch to add conditional register
of the hooks.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
CONFIG_NF_CT_PROTO_UDPLITE is no more a tristate. When set to y,
connection tracking support for UDPlite protocol is built-in into
nf_conntrack.ko.
footprint test:
$ ls -l net/netfilter/nf_conntrack{_proto_udplite,}.ko \
net/ipv4/netfilter/nf_conntrack_ipv4.ko \
net/ipv6/netfilter/nf_conntrack_ipv6.ko
(builtin)|| udplite| ipv4 | ipv6 |nf_conntrack
---------++--------+--------+--------+--------------
none || 432538 | 828755 | 828676 | 6141434
UDPlite || - | 829649 | 829362 | 6498204
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
CONFIG_NF_CT_PROTO_SCTP is no more a tristate. When set to y, connection
tracking support for SCTP protocol is built-in into nf_conntrack.ko.
footprint test:
$ ls -l net/netfilter/nf_conntrack{_proto_sctp,}.ko \
net/ipv4/netfilter/nf_conntrack_ipv4.ko \
net/ipv6/netfilter/nf_conntrack_ipv6.ko
(builtin)|| sctp | ipv4 | ipv6 | nf_conntrack
---------++--------+--------+--------+--------------
none || 498243 | 828755 | 828676 | 6141434
SCTP || - | 829254 | 829175 | 6547872
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
CONFIG_NF_CT_PROTO_DCCP is no more a tristate. When set to y, connection
tracking support for DCCP protocol is built-in into nf_conntrack.ko.
footprint test:
$ ls -l net/netfilter/nf_conntrack{_proto_dccp,}.ko \
net/ipv4/netfilter/nf_conntrack_ipv4.ko \
net/ipv6/netfilter/nf_conntrack_ipv6.ko
(builtin)|| dccp | ipv4 | ipv6 | nf_conntrack
---------++--------+--------+--------+--------------
none || 469140 | 828755 | 828676 | 6141434
DCCP || - | 830566 | 829935 | 6533526
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Simon Horman says:
====================
IPVS Updates for v4.10
please consider these enhancements to the IPVS for v4.10.
* Decrement the IP ttl in all the modes in order to prevent infinite
route loops. Thanks to Dwip Banerjee.
* Use IS_ERR_OR_NULL macro. Clean-up from Gao Feng.
====================
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
So we can autoload nfnetlink_log.ko when the user adding nft log
group X rule in netdev family.
Signed-off-by: Liping Zhang <zlpnobody@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
In netdev family, we will handle non ethernet packets, so using
eth_hdr(skb)->h_proto is incorrect.
Meanwhile, we can use socket(AF_PACKET...) to sending packets, so
skb->protocol is not always set in bridge family.
Add an extra parameter into nf_log_l2packet to solve this issue.
Fixes: 1fddf4bad0 ("netfilter: nf_log: add packet logging for netdev family")
Signed-off-by: Liping Zhang <zlpnobody@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
CONFIG_NF_NAT_PROTO_UDPLITE is no more a tristate. When set to y, NAT
support for UDPlite protocol is built-in into nf_nat.ko.
footprint test:
(nf_nat_proto_) |udplite || nf_nat
--------------------------+--------++--------
no builtin | 408048 || 2241312
UDPLITE builtin | - || 2577256
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
CONFIG_NF_NAT_PROTO_SCTP is no more a tristate. When set to y, NAT
support for SCTP protocol is built-in into nf_nat.ko.
footprint test:
(nf_nat_proto_) | sctp || nf_nat
--------------------------+--------++--------
no builtin | 428344 || 2241312
SCTP builtin | - || 2597032
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
CONFIG_NF_NAT_PROTO_DCCP is no more a tristate. When set to y, NAT
support for DCCP protocol is built-in into nf_nat.ko.
footprint test:
(nf_nat_proto_) | dccp || nf_nat
--------------------------+--------++--------
no builtin | 409800 || 2241312
DCCP builtin | - || 2578968
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The email address has changed, let's update the copyright statements.
Signed-off-by: Arturo Borrero Gonzalez <arturo@debian.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
In function dcbnl_cee_fill(), returns the value of variable err on
errors. However, on some error paths (e.g. nla put fails), its value may
be 0. It may be better to explicitly set a negative errno to variable
err before returning.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=188881
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implemented RFC7527 Enhanced DAD.
IPv6 duplicate address detection can fail if there is some temporary
loopback of Ethernet frames. RFC7527 solves this by including a random
nonce in the NS messages used for DAD, and if an NS is received with the
same nonce it is assumed to be a looped back DAD probe and is ignored.
RFC7527 is enabled by default. Can be disabled by setting both of
conf/{all,interface}/enhanced_dad to zero.
Signed-off-by: Erik Nordmark <nordmark@arista.com>
Signed-off-by: Bob Gilligan <gilligan@arista.com>
Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit b90eb75494 ("fib: introduce FIB notification infrastructure")
introduced a new notification chain to notify listeners (f.e., switchdev
drivers) about addition and deletion of routes.
However, upon registration to the chain the FIB tables can already be
populated, which means potential listeners will have an incomplete view
of the tables.
Solve that by dumping the FIB tables and replaying the events to the
passed notification block. The dump itself is done using RCU in order
not to starve consumers that need RTNL to make progress.
The integrity of the dump is ensured by reading the FIB change sequence
counter before and after the dump under RTNL. This allows us to avoid
the problematic situation in which the dumping process sends a ENTRY_ADD
notification following ENTRY_DEL generated by another process holding
RTNL.
Callers of the registration function may pass a callback that is
executed in case the dump was inconsistent with current FIB tables.
The number of retries until a consistent dump is achieved is set to a
fixed number to prevent callers from looping for long periods of time.
In case current limit proves to be problematic in the future, it can be
easily converted to be configurable using a sysctl.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The next patch will enable listeners of the FIB notification chain to
request a dump of the FIB tables. However, since RTNL isn't taken during
the dump, it's possible for the FIB tables to change mid-dump, which
will result in inconsistency between the listener's table and the
kernel's.
Allow listeners to know about changes that occurred mid-dump, by adding
a change sequence counter to each net namespace. The counter is
incremented just before a notification is sent in the FIB chain.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order not to hold RTNL for long periods of time we're going to dump
the FIB tables using RCU.
Convert the FIB notification chain to be atomic, as we can't block in
RCU critical sections.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The FIB notification chain is going to be converted to an atomic chain,
which means switchdev drivers will have to offload FIB entries in
deferred work, as hardware operations entail sleeping.
However, while the work is queued fib info might be freed, so a
reference must be taken. To release the reference (and potentially free
the fib info) fib_info_put() will be called, which in turn calls
free_fib_info().
Export free_fib_info() so that modules will be able to invoke
fib_info_put().
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: 255cb30425 ("net/sched: act_mirred: Add new tc_action_ops get_dev()")
Cc: Hadar Hen Zion <hadarh@mellanox.com>
Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before commit 850cbaddb5 ("udp: use it's own memory accounting
schema"), the udp protocol allowed sk_rmem_alloc to grow beyond
the rcvbuf by the whole current packet's truesize. After said commit
we allow sk_rmem_alloc to exceed the rcvbuf only if the receive queue
is empty. As reported by Jesper this cause a performance regression
for some (small) values of rcvbuf.
This commit is intended to fix the regression restoring the old
handling of the rcvbuf limit.
Reported-by: Jesper Dangaard Brouer <brouer@redhat.com>
Fixes: 850cbaddb5 ("udp: use it's own memory accounting schema")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- fix checking for failed allocation of TVLV blocks in TT local data,
by Sven Eckelmann
-----BEGIN PGP SIGNATURE-----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=Y2ED
-----END PGP SIGNATURE-----
Merge tag 'batadv-net-for-davem-20161202' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
Here is another batman-adv bugfix:
- fix checking for failed allocation of TVLV blocks in TT local data,
by Sven Eckelmann
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Under heavy stress, timer used in estimators tend to slowly be delayed
by a few jiffies, leading to inaccuracies.
Lets remember what was the last scheduled jiffies so that we get more
precise estimations, without having to add a multiply/divide in the loop
to account for the drifts.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net_generic() function is both a) inline and b) used ~600 times.
It has the following code inside
...
ptr = ng->ptr[id - 1];
...
"id" is never compile time constant so compiler is forced to subtract 1.
And those decrements or LEA [r32 - 1] instructions add up.
We also start id'ing from 1 to catch bugs where pernet sybsystem id
is not initialized and 0. This is quite pointless idea (nothing will
work or immediate interference with first registered subsystem) in
general but it hints what needs to be done for code size reduction.
Namely, overlaying allocation of pointer array and fixed part of
structure in the beginning and using usual base-0 addressing.
Ids are just cookies, their exact values do not matter, so lets start
with 3 on x86_64.
Code size savings (oh boy): -4.2 KB
As usual, ignore the initial compiler stupidity part of the table.
add/remove: 0/0 grow/shrink: 12/670 up/down: 89/-4297 (-4208)
function old new delta
tipc_nametbl_insert_publ 1250 1270 +20
nlmclnt_lookup_host 686 703 +17
nfsd4_encode_fattr 5930 5941 +11
nfs_get_client 1050 1061 +11
register_pernet_operations 333 342 +9
tcf_mirred_init 843 849 +6
tcf_bpf_init 1143 1149 +6
gss_setup_upcall 990 994 +4
idmap_name_to_id 432 434 +2
ops_init 274 275 +1
nfsd_inject_forget_client 259 260 +1
nfs4_alloc_client 612 613 +1
tunnel_key_walker 164 163 -1
...
tipc_bcbase_select_primary 392 360 -32
mac80211_hwsim_new_radio 2808 2767 -41
ipip6_tunnel_ioctl 2228 2186 -42
tipc_bcast_rcv 715 672 -43
tipc_link_build_proto_msg 1140 1089 -51
nfsd4_lock 3851 3796 -55
tipc_mon_rcv 1012 956 -56
Total: Before=156643951, After=156639743, chg -0.00%
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is precursor to fixing "[id - 1]" bloat inside net_generic().
Name "s" is chosen to complement name "u" often used for dummy unions.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Publishing net_generic pointer is done with silly mistake: new array is
published BEFORE setting freshly acquired pernet subsystem pointer.
memcpy
rcu_assign_pointer
kfree_rcu
ng->ptr[id - 1] = data;
This bug was introduced with commit dec827d174
("[NETNS]: The generic per-net pointers.") in the glorious days of
chopping networking stack into containers proper 8.5 years ago (whee...)
How it didn't trigger for so long?
Well, you need quite specific set of conditions:
*) race window opens once per pernet subsystem addition
(read: modprobe or boot)
*) not every pernet subsystem is eligible (need ->id and ->size)
*) not every pernet subsystem is vulnerable (need incorrect or absense
of ordering of register_pernet_sybsys() and actually using net_generic())
*) to hide the bug even more, default is to preallocate 13 pointers which
is actually quite a lot. You need IPv6, netfilter, bridging etc together
loaded to trigger reallocation in the first place. Trimmed down
config are OK.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Couple conflicts resolved here:
1) In the MACB driver, a bug fix to properly initialize the
RX tail pointer properly overlapped with some changes
to support variable sized rings.
2) In XGBE we had a "CONFIG_PM" --> "CONFIG_PM_SLEEP" fix
overlapping with a reorganization of the driver to support
ACPI, OF, as well as PCI variants of the chip.
3) In 'net' we had several probe error path bug fixes to the
stmmac driver, meanwhile a lot of this code was cleaned up
and reorganized in 'net-next'.
4) The cls_flower classifier obtained a helper function in
'net-next' called __fl_delete() and this overlapped with
Daniel Borkamann's bug fix to use RCU for object destruction
in 'net'. It also overlapped with Jiri's change to guard
the rhashtable_remove_fast() call with a check against
tc_skip_sw().
5) In mlx4, a revert bug fix in 'net' overlapped with some
unrelated changes in 'net-next'.
6) In geneve, a stale header pointer after pskb_expand_head()
bug fix in 'net' overlapped with a large reorganization of
the same code in 'net-next'. Since the 'net-next' code no
longer had the bug in question, there was nothing to do
other than to simply take the 'net-next' hunks.
Signed-off-by: David S. Miller <davem@davemloft.net>
CAP_NET_ADMIN users should not be allowed to set negative
sk_sndbuf or sk_rcvbuf values, as it can lead to various memory
corruptions, crashes, OOM...
Note that before commit 8298193012 ("net: cleanups in
sock_setsockopt()"), the bug was even more serious, since SO_SNDBUF
and SO_RCVBUF were vulnerable.
This needs to be backported to all known linux kernels.
Again, many thanks to syzkaller team for discovering this gem.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Qian Zhang (张谦) reported a potential socket buffer overflow in
tipc_msg_build() which is also known as CVE-2016-8632: due to
insufficient checks, a buffer overflow can occur if MTU is too short for
even tipc headers. As anyone can set device MTU in a user/net namespace,
this issue can be abused by a regular user.
As agreed in the discussion on Ben Hutchings' original patch, we should
check the MTU at the moment a bearer is attached rather than for each
processed packet. We also need to repeat the check when bearer MTU is
adjusted to new device MTU. UDP case also needs a check to avoid
overflow when calculating bearer MTU.
Fixes: b97bf3fd8f ("[TIPC] Initial merge")
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reported-by: Qian Zhang (张谦) <zhangqian-c@360.cn>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add socket family, type and protocol to bpf_sock allowing bpf programs
read-only access.
Add __sk_flags_offset[0] to struct sock before the bitfield to
programmtically determine the offset of the unsigned int containing
protocol and type.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new cgroup based program type, BPF_PROG_TYPE_CGROUP_SOCK. Similar to
BPF_PROG_TYPE_CGROUP_SKB programs can be attached to a cgroup and run
any time a process in the cgroup opens an AF_INET or AF_INET6 socket.
Currently only sk_bound_dev_if is exported to userspace for modification
by a bpf program.
This allows a cgroup to be configured such that AF_INET{6} sockets opened
by processes are automatically bound to a specific device. In turn, this
enables the running of programs that do not support SO_BINDTODEVICE in a
specific VRF context / L3 domain.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If some error is encountered in rds_tcp_init_net, make sure to
unregister_netdevice_notifier(), else we could trigger a panic
later on, when the modprobe from a netns fails.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support hardware offloading when the device given by the tc
rule is different from the Hardware underline device, extract the mirred
(egress) device from the tc action when a filter is added, using the new
tc_action_ops, get_dev().
Flower caches the information about the mirred device and use it for
calling ndo_setup_tc in filter change, update stats and delete.
Calling ndo_setup_tc of the mirred (egress) device instead of the
ingress device will allow a resolution between the software ingress
device and the underline hardware device.
The resolution will take place inside the offloading driver using
'egress_device' flag added to tc_to_netdev struct which is provided to
the offloading driver.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding support to a new tc_action_ops.
get_dev is a general option which allows to get the underline
device when trying to offload a tc rule.
In case of mirred action the returned device is the mirred (egress)
device.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of providing many arguments to fl_hw_{replace/destroy}_filter
functions, just provide cls_fl_filter struct that includes all the relevant
args.
This patches doesn't add any new functionality.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check skip_hw flag isn't set before calling
fl_hw_{replace/destroy}_filter and fl_hw_update_stats functions.
Replace the call to tc_should_offload with tc_can_offload.
tc_can_offload only checks if the device supports offloading, the check for
skip_hw flag is done earlier in the flow.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric says: "By looking at tcpdump, and TS val of xmit packets of multiple
flows, we can deduct the relative qdisc delays (think of fq pacing).
This should work even if we have one flow per remote peer."
Having random per flow (or host) offsets doesn't allow that anymore so add
a way to turn this off.
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
jiffies based timestamps allow for easy inference of number of devices
behind NAT translators and also makes tracking of hosts simpler.
commit ceaa1fef65 ("tcp: adding a per-socket timestamp offset")
added the main infrastructure that is needed for per-connection ts
randomization, in particular writing/reading the on-wire tcp header
format takes the offset into account so rest of stack can use normal
tcp_time_stamp (jiffies).
So only two items are left:
- add a tsoffset for request sockets
- extend the tcp isn generator to also return another 32bit number
in addition to the ISN.
Re-use of ISN generator also means timestamps are still monotonically
increasing for same connection quadruple, i.e. PAWS will still work.
Includes fixes from Eric Dumazet.
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit ae148b0858
("ip6_tunnel: Update skb->protocol to ETH_P_IPV6 in ip6_tnl_xmit()").
skb->protocol is now set in __ip_local_out() and __ip6_local_out() before
dst_output() is called. It is no longer necessary to do it for each tunnel.
Cc: stable@vger.kernel.org
Signed-off-by: Eli Cooper <elicooper@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When xfrm is applied to TSO/GSO packets, it follows this path:
xfrm_output() -> xfrm_output_gso() -> skb_gso_segment()
where skb_gso_segment() relies on skb->protocol to function properly.
This patch sets skb->protocol to ETH_P_IPV6 before dst_output() is called,
fixing a bug where GSO packets sent through an ipip6 tunnel are dropped
when xfrm is involved.
Cc: stable@vger.kernel.org
Signed-off-by: Eli Cooper <elicooper@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When xfrm is applied to TSO/GSO packets, it follows this path:
xfrm_output() -> xfrm_output_gso() -> skb_gso_segment()
where skb_gso_segment() relies on skb->protocol to function properly.
This patch sets skb->protocol to ETH_P_IP before dst_output() is called,
fixing a bug where GSO packets sent through a sit tunnel are dropped
when xfrm is involved.
Cc: stable@vger.kernel.org
Signed-off-by: Eli Cooper <elicooper@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When packet_set_ring creates a ring buffer it will initialize a
struct timer_list if the packet version is TPACKET_V3. This value
can then be raced by a different thread calling setsockopt to
set the version to TPACKET_V1 before packet_set_ring has finished.
This leads to a use-after-free on a function pointer in the
struct timer_list when the socket is closed as the previously
initialized timer will not be deleted.
The bug is fixed by taking lock_sock(sk) in packet_setsockopt when
changing the packet version while also taking the lock at the start
of packet_set_ring.
Fixes: f6fb8f100b ("af-packet: TPACKET_V3 flexible buffer implementation.")
Signed-off-by: Philip Pettersson <philip.pettersson@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only when ICMP packets are enqueued onto the error queue,
sk_err is also set. Before f5f99309fa (sock: do not set sk_err
in sock_dequeue_err_skb), a subsequent error queue read
would set sk_err to the next error on the queue, or 0 if empty.
As no error types other than ICMP set this field, sk_err should
not be modified upon dequeuing them.
Only for ICMP errors, reset the (racy) sk_err. Some applications,
like traceroute, rely on it and go into a futile busy POLLERR
loop otherwise.
In principle, sk_err has to be set while an ICMP error is queued.
Testing is_icmp_err_skb(skb_next) approximates this without
requiring a full queue walk. Applications that receive both ICMP
and other errors cannot rely on this legacy behavior, as other
errors do not set sk_err in the first place.
Fixes: f5f99309fa (sock: do not set sk_err in sock_dequeue_err_skb)
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Registers new BPF program types which correspond to the LWT hooks:
- BPF_PROG_TYPE_LWT_IN => dst_input()
- BPF_PROG_TYPE_LWT_OUT => dst_output()
- BPF_PROG_TYPE_LWT_XMIT => lwtunnel_xmit()
The separate program types are required to differentiate between the
capabilities each LWT hook allows:
* Programs attached to dst_input() or dst_output() are restricted and
may only read the data of an skb. This prevent modification and
possible invalidation of already validated packet headers on receive
and the construction of illegal headers while the IP headers are
still being assembled.
* Programs attached to lwtunnel_xmit() are allowed to modify packet
content as well as prepending an L2 header via a newly introduced
helper bpf_skb_change_head(). This is safe as lwtunnel_xmit() is
invoked after the IP header has been assembled completely.
All BPF programs receive an skb with L3 headers attached and may return
one of the following error codes:
BPF_OK - Continue routing as per nexthop
BPF_DROP - Drop skb and return EPERM
BPF_REDIRECT - Redirect skb to device as per redirect() helper.
(Only valid in lwtunnel_xmit() context)
The return codes are binary compatible with their TC_ACT_
relatives to ease compatibility.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
A route on the output path hitting a RTN_LOCAL route will keep the dst
associated on its way through the loopback device. On the receive path,
the dst_input() call will thus invoke the input handler of the route
created in the output path. Thus, lwt redirection for input must be done
for dsts allocated in the otuput path as well.
Also, if a route is cached in the input path, the allocated dst should
respect lwtunnel configuration on the nexthop as well.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
orig_output for IPv4 was only set for dsts which hit an input route.
Set it consistently for locally generated traffic as well to allow
lwt to continue the dst_output() path as configured by the nexthop.
Fixes: 2536862311 ("lwt: Add support to redirect dst.input")
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the correct attribute constant names IFLA_GSO_MAX_{SEGS,SIZE}
instead of IFLA_MAX_GSO_{SEGS,SIZE} for the comments int nlmsg_size().
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
batadv_tt_prepare_tvlv_local_data can fail to allocate the memory for the
new TVLV block. The caller is informed about this problem with the returned
length of 0. Not checking this value results in an invalid memory access
when either tt_data or tt_change is accessed.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 7ea7b4a142 ("batman-adv: make the TT CRC logic VLAN specific")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
xs_connect() contains an exponential backoff mechanism so the repeated
connection attempts are delayed by longer and longer amounts.
This is appropriate when the connection failed due to a timeout, but
it not appropriate when a definitive "no" answer is received. In such
cases, call_connect_status() imposes a minimum 3-second back-off, so
not having the exponetial back-off will never result in immediate
retries.
The current situation is a problem when the NFS server tries to
register with rpcbind but rpcbind isn't running. All connection
attempts are made on the same "xprt" and as the connection is never
"closed", the exponential back delays successive attempts to register,
or de-register, different protocols. This results in a multi-minute
delay with no benefit.
So, when call_connect_status() receives a definitive "no", use
xprt_conditional_disconnect() to cancel the previous connection attempt.
This will set XPRT_CLOSE_WAIT so that xprt->ops->close() calls xs_close()
which resets the reestablish_timeout.
To ensure xprt_conditional_disconnect() does the right thing, we
ensure that rq_connect_cookie is set before a connection attempt, and
allow xprt_conditional_disconnect() to complete even when the
transport is not fully connected.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Before this patch, function ndo_dflt_fdb_dump() will always return code
from uc fdb dump. The reture code of mc fdb dump is lost.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net): ipsec 2016-12-01
1) Change the error value when someone tries to run 32bit
userspace on a 64bit host from -ENOTSUPP to the userspace
exported -EOPNOTSUPP. Fix from Yi Zhao.
2) On inbound, ESN sequence numbers are already in network
byte order. So don't try to convert it again, this fixes
integrity verification for ESN. Fixes from Tobias Brunner.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
This is a large batch of Netfilter fixes for net, they are:
1) Three patches to fix NAT conversion to rhashtable: Switch to rhlist
structure that allows to have several objects with the same key.
Moreover, fix wrong comparison logic in nf_nat_bysource_cmp() as this is
expecting a return value similar to memcmp(). Change location of
the nat_bysource field in the nf_conn structure to avoid zeroing
this as it breaks interaction with SLAB_DESTROY_BY_RCU and lead us
to crashes. From Florian Westphal.
2) Don't allow malformed fragments go through in IPv6, drop them,
otherwise we hit GPF, patch from Florian Westphal.
3) Fix crash if attributes are missing in nft_range, from Liping Zhang.
4) Fix arptables 32-bits userspace 64-bits kernel compat, from Hongxu Jia.
5) Two patches from David Ahern to fix netfilter interaction with vrf.
From David Ahern.
6) Fix element timeout calculation in nf_tables, we take milliseconds
from userspace, but we use jiffies from kernelspace. Patch from
Anders K. Pedersen.
7) Missing validation length netlink attribute for nft_hash, from
Laura Garcia.
8) Fix nf_conntrack_helper documentation, we don't default to off
anymore for a bit of time so let's get this in sync with the code.
I know is late but I think these are important, specifically the NAT
bits, as they are mostly addressing fallout from recent changes. I also
read there are chances to have -rc8, if that is the case, that would
also give us a bit more time to test this.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code results in:
Nov 7 14:50:19 klimt kernel: svcrdma: newxprt->sc_cm_id=ffff88085590c800,
newxprt->sc_pd=ffff880852a7ce00#012 cm_id->device=ffff88084dd20000,
sc_pd->device=ffff88084dd20000#012 cap.max_send_wr = 272#012
cap.max_recv_wr = 34#012 cap.max_send_sge = 32#012
cap.max_recv_sge = 32
Nov 7 14:50:19 klimt kernel: svcrdma: new connection ffff880855908000
accepted with the following attributes:#012 local_ip :
10.0.0.5#012 local_port#011 : 20049#012 remote_ip :
10.0.0.2#012 remote_port : 59909#012 max_sge : 32#012
max_sge_rd : 30#012 sq_depth : 272#012 max_requests :
32#012 ord : 16
Split up the output over multiple dprintks and take the opportunity
to fix the display of IPv6 addresses.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Clean up.
linux-2.6/net/sunrpc/xprtrdma/svc_rdma_recvfrom.c: In function
‘rdma_copy_tail’:
linux-2.6/net/sunrpc/xprtrdma/svc_rdma_recvfrom.c:376:6: warning:
variable ‘ret’ set but not used [-Wunused-but-set-variable]
int ret;
^
Fixes: a97c331f9a ("svcrdma: Handle additional inline content")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Clean up.
/linux-2.6/net/sunrpc/xprtrdma/svc_rdma_backchannel.c: In function
‘xprt_rdma_bc_allocate’:
linux-2.6/net/sunrpc/xprtrdma/svc_rdma_backchannel.c:169:23: warning:
variable ‘rdma’ set but not used [-Wunused-but-set-variable]
struct svcxprt_rdma *rdma;
^
Fixes: 5d252f90a8 ("svcrdma: Add class for RDMA backwards ...")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Clean up: Completion status is already reported in the individual
completion handlers. Save a few bytes in struct svc_rdma_op_ctxt.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Clean up: sc_dma_used is not required for correct operation. It is
simply a debugging tool to report when svcrdma has leaked DMA maps.
However, manipulating an atomic has a measurable CPU cost, and DMA
map accounting specific to svcrdma will be meaningless once svcrdma
is converted to use the new generic r/w API.
A similar kind of debug accounting can be done simply by enabling
the IOMMU or by using CONFIG_DMA_API_DEBUG, CONFIG_IOMMU_DEBUG, and
CONFIG_IOMMU_LEAK.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
svcrdma's current SQ accounting algorithm takes sc_lock and disables
bottom-halves while posting all RDMA Read, Write, and Send WRs.
This is relatively heavyweight serialization. And note that Write and
Send are already fully serialized by the xpt_mutex.
Using a single atomic_t should be all that is necessary to guarantee
that ib_post_send() is called only when there is enough space on the
send queue. This is what the other RDMA-enabled storage targets do.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
The current sendto code appears to support clients that provide only
one of a Read list, a Write list, or a Reply chunk. My reading of
that code is that it doesn't support the following cases:
- Read list + Write list
- Read list + Reply chunk
- Write list + Reply chunk
- Read list + Write list + Reply chunk
The protocol allows more than one Read or Write chunk in those
lists. Some clients do send a Read list and Reply chunk
simultaneously. NFSv4 WRITE uses a Read list for the data payload,
and a Reply chunk because the GETATTR result in the reply can
contain a large object like an ACL.
Generalize one of the sendto code paths needed to support all of
the above cases, and attempt to ensure that only one pass is done
through the RPC Call's transport header to gather chunk list
information for building the reply.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
S5.3.3.1 of RFC 2203 requires that an incoming GSS-wrapped message
whose sequence number lies outside the current window is dropped.
The rationale is:
The reason for discarding requests silently is that the server
is unable to determine if the duplicate or out of range request
was due to a sequencing problem in the client, network, or the
operating system, or due to some quirk in routing, or a replay
attack by an intruder. Discarding the request allows the client
to recover after timing out, if indeed the duplication was
unintentional or well intended.
However, clients may rely on the server dropping the connection to
indicate that a retransmit is needed. Without a connection reset, a
client can wait forever without retransmitting, and the workload
just stops dead. I've reproduced this behavior by running xfstests
generic/323 on an NFSv4.0 mount with proto=rdma and sec=krb5i.
To address this issue, have the server close the connection when it
silently discards an incoming message due to a GSS sequence number
problem.
There are a few other places where the server will never reply.
Change those spots in a similar fashion.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Logic copied from xs_setup_bc_tcp().
Fixes: 39a9beab5a ('rpc: share one xps between all backchannels')
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Commit e2d118a1cb ("net: inet: Support UID-based routing in IP
protocols.") made __build_flow_key call sock_net(sk) to determine
the network namespace of the passed-in socket. This crashes if sk
is NULL.
Fix this by getting the network namespace from the skb instead.
Fixes: e2d118a1cb ("net: inet: Support UID-based routing in IP protocols.")
Reported-by: Erez Shitrit <erezsh@dev.mellanox.co.il>
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since 09d9686047 ("netfilter: x_tables: do compat validation via
translate_table"), it used compatr structure to assign newinfo
structure. In translate_compat_table of ip_tables.c and ip6_tables.c,
it used compatr->hook_entry to replace info->hook_entry and
compatr->underflow to replace info->underflow, but not do the same
replacement in arp_tables.c.
It caused invoking 32-bit "arptbale -P INPUT ACCEPT" failed in 64bit
kernel.
--------------------------------------
root@qemux86-64:~# arptables -P INPUT ACCEPT
root@qemux86-64:~# arptables -P INPUT ACCEPT
ERROR: Policy for `INPUT' offset 448 != underflow 0
arptables: Incompatible with this kernel
--------------------------------------
Fixes: 09d9686047 ("netfilter: x_tables: do compat validation via translate_table")
Signed-off-by: Hongxu Jia <hongxu.jia@windriver.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The '!(addr && ipv6_addr_equal(addr, laddr))' part of the conditional
matches if addr is NULL or if addr != laddr.
But the intend of __l2tp_ip6_bind_lookup() is to find a sockets with
the same address, so the ipv6_addr_equal() condition needs to be
inverted.
For better clarity and consistency with the rest of the expression, the
(!X || X == Y) notation is used instead of !(X && X != Y).
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
When looking up an l2tp socket, we must consider a null netdevice id as
wild card. There are currently two problems caused by
__l2tp_ip_bind_lookup() not considering 'dif' as wild card when set to 0:
* A socket bound to a device (i.e. with sk->sk_bound_dev_if != 0)
never receives any packet. Since __l2tp_ip_bind_lookup() is called
with dif == 0 in l2tp_ip_recv(), sk->sk_bound_dev_if is always
different from 'dif' so the socket doesn't match.
* Two sockets, one bound to a device but not the other, can be bound
to the same address. If the first socket binding to the address is
the one that is also bound to a device, the second socket can bind
to the same address without __l2tp_ip_bind_lookup() noticing the
overlap.
To fix this issue, we need to consider that any null device index, be
it 'sk->sk_bound_dev_if' or 'dif', matches with any other value.
We also need to pass the input device index to __l2tp_ip_bind_lookup()
on reception so that sockets bound to a device never receive packets
from other devices.
This patch fixes l2tp_ip6 in the same way.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's not enough to check for sockets bound to same address at the
beginning of l2tp_ip{,6}_bind(): even if no socket is found at that
time, a socket with the same address could be bound before we take
the l2tp lock again.
This patch moves the lookup right before inserting the new socket, so
that no change can ever happen to the list between address lookup and
socket insertion.
Care is taken to avoid side effects on the socket in case of failure.
That is, modifications of the socket are done after the lookup, when
binding is guaranteed to succeed, and before releasing the l2tp lock,
so that concurrent lookups will always see fully initialised sockets.
For l2tp_ip, 'ret' is set to -EINVAL before checking the SOCK_ZAPPED
bit. Error code was mistakenly set to -EADDRINUSE on error by commit
32c231164b ("l2tp: fix racy SOCK_ZAPPED flag check in l2tp_ip{,6}_bind()").
Using -EINVAL restores original behaviour.
For l2tp_ip6, the lookup is now always done with the correct bound
device. Before this patch, when binding to a link-local address, the
lookup was done with the original sk->sk_bound_dev_if, which was later
overwritten with addr->l2tp_scope_id. Lookup is now performed with the
final sk->sk_bound_dev_if value.
Finally, the (addr_len >= sizeof(struct sockaddr_in6)) check has been
dropped: addr is a sockaddr_l2tpip6 not sockaddr_in6 and addr_len has
already been checked at this point (this part of the code seems to have
been copy-pasted from net/ipv6/raw.c).
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Socket must be held while under the protection of the l2tp lock; there
is no guarantee that sk remains valid after the read_unlock_bh() call.
Same issue for l2tp_ip and l2tp_ip6.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Socket flags aren't updated atomically, so the socket must be locked
while reading the SOCK_ZAPPED flag.
This issue exists for both l2tp_ip and l2tp_ip6. For IPv6, this patch
also brings error handling for __ip6_datagram_connect() failures.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently loop index 'idx' is used as the index in the neigh list of interest.
It's increased only when the neigh is dumped. It's not the absolute index in
the list. Because there is no info to record which neigh has already be scanned
by previous loop. This will cause the filtered out neighs to be scanned mulitple
times.
This patch make idx as the absolute index in the list, it will increase no matter
whether the neigh is filtered. This will prevent the above problem.
And this is in line with other dump functions.
v2:
- take David Ahern's advice to do simple change
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If nf_ct_frag6_gather() returns an error other than -EINPROGRESS, it
means that we still have a reference to the skb. We should free it
before returning from handle_fragments, as stated in the comment above.
Fixes: daaa7d647f ("netfilter: ipv6: avoid nf_iterate recursion")
CC: Florian Westphal <fw@strlen.de>
CC: Pravin B Shelar <pshelar@ovn.org>
CC: Joe Stringer <joe@ovn.org>
Signed-off-by: Daniele Di Proietto <diproiettod@ovn.org>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an IFLA_XDP_FLAGS attribute that can be passed for setting up
XDP along with IFLA_XDP_FD, which eventually allows user space to
implement typical add/replace/delete logic for programs. Right now,
calling into dev_change_xdp_fd() will always replace previous programs.
When passed XDP_FLAGS_UPDATE_IF_NOEXIST, we can handle this more
graceful when requested by returning -EBUSY in case we try to
attach a new program, but we find that another one is already
attached. This will be used by upcoming front-end for iproute2 as
well.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch exports the sender chronograph stats via the socket
SO_TIMESTAMPING channel. Currently we can instrument how long a
particular application unit of data was queued in TCP by tracking
SOF_TIMESTAMPING_TX_SOFTWARE and SOF_TIMESTAMPING_TX_SCHED. Having
these sender chronograph stats exported simultaneously along with
these timestamps allow further breaking down the various sender
limitation. For example, a video server can tell if a particular
chunk of video on a connection takes a long time to deliver because
TCP was experiencing small receive window. It is not possible to
tell before this patch without packet traces.
To prepare these stats, the user needs to set
SOF_TIMESTAMPING_OPT_STATS and SOF_TIMESTAMPING_OPT_TSONLY flags
while requesting other SOF_TIMESTAMPING TX timestamps. When the
timestamps are available in the error queue, the stats are returned
in a separate control message of type SCM_TIMESTAMPING_OPT_STATS,
in a list of TLVs (struct nlattr) of types: TCP_NLA_BUSY_TIME,
TCP_NLA_RWND_LIMITED, TCP_NLA_SNDBUF_LIMITED. Unit is microsecond.
Signed-off-by: Francis Yan <francisyyan@gmail.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch exports all the sender chronograph measurements collected
in the previous patches to TCP_INFO interface. Note that busy time
exported includes all the other sending limits (rwnd-limited,
sndbuf-limited). Internally the time unit is jiffy but externally
the measurements are in microseconds for future extensions.
Signed-off-by: Francis Yan <francisyyan@gmail.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch measures the amount of time when TCP runs out of new data
to send to the network due to insufficient send buffer, while TCP
is still busy delivering (i.e. write queue is not empty). The goal
is to indicate either the send buffer autotuning or user SO_SNDBUF
setting has resulted network under-utilization.
The measurement starts conservatively by checking various conditions
to minimize false claims (i.e. under-estimation is more likely).
The measurement stops when the SOCK_NOSPACE flag is cleared. But it
does not account the time elapsed till the next application write.
Also the measurement only starts if the sender is still busy sending
data, s.t. the limit accounted is part of the total busy time.
Signed-off-by: Francis Yan <francisyyan@gmail.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch measures the total time when the TCP stops sending because
the receiver's advertised window is not large enough. Note that
once the limit is lifted we are likely in the busy status if we
have data pending.
Signed-off-by: Francis Yan <francisyyan@gmail.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch measures TCP busy time, which is defined as the period
of time when sender has data (or FIN) to send. The time starts when
data is buffered and stops when the write queue is flushed by ACKs
or error events.
Note the busy time does not include SYN time, unless data is
included in SYN (i.e. Fast Open). It does include FIN time even
if the FIN carries no payload. Excluding pure FIN is possible but
would incur one additional test in the fast path, which may not
be worth it.
Signed-off-by: Francis Yan <francisyyan@gmail.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements the skeleton of the TCP chronograph
instrumentation on sender side limits:
1) idle (unspec)
2) busy sending data other than 3-4 below
3) rwnd-limited
4) sndbuf-limited
The limits are enumerated 'tcp_chrono'. Since a connection in
theory can idle forever, we do not track the actual length of this
uninteresting idle period. For the rest we track how long the sender
spends in each limit. At any point during the life time of a
connection, the sender must be in one of the four states.
If there are multiple conditions worthy of tracking in a chronograph
then the highest priority enum takes precedence over
the other conditions. So that if something "more interesting"
starts happening, stop the previous chrono and start a new one.
The time unit is jiffy(u32) in order to save space in tcp_sock.
This implies application must sample the stats no longer than every
49 days of 1ms jiffy.
Signed-off-by: Francis Yan <francisyyan@gmail.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I've observed a NULL pointer dereference in ieee802154_del_iface() during
netlink fuzzing. It's the ->wpan_phy dereference here:
phy = dev->ieee802154_ptr->wpan_phy;
My bet is that we're not checking that this is an IEEE802154 interface,
so let's do what ieee802154_nl_get_dev() is doing. (Maybe we should even
be calling this directly?)
Cc: Lennert Buytenhek <buytenh@wantstofly.org>
Cc: Alexander Aring <alex.aring@gmail.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Sergey Lapin <slapin@ossfans.org>
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Acked-by: Alexander Aring <aar@pengutronix.de>
Signed-off-by: Stefan Schmidt <stefan@osg.samsung.com>
When handling inbound packets, the two halves of the sequence number
stored on the skb are already in network order.
Fixes: 000ae7b269 ("esp6: Switch to new AEAD interface")
Signed-off-by: Tobias Brunner <tobias@strongswan.org>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
When handling inbound packets, the two halves of the sequence number
stored on the skb are already in network order.
Fixes: 7021b2e1cd ("esp4: Switch to new AEAD interface")
Signed-off-by: Tobias Brunner <tobias@strongswan.org>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
It doesn't support to run 32bit 'ip' to set xfrm objdect on 64bit host.
But the return value is unknown for user program:
ip xfrm policy list
RTNETLINK answers: Unknown error 524
Replace ENOTSUPP with EOPNOTSUPP:
ip xfrm policy list
RTNETLINK answers: Operation not supported
Signed-off-by: Yi Zhao <yi.zhao@windriver.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Make sure to deregister and free any fixed-link PHY registered using
of_phy_register_fixed_link() on slave-setup errors and on slave destroy.
Fixes: 0d8bcdd383 ("net: dsa: allow for more complex PHY setups")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add helper to deregister fixed-link PHYs registered using
of_phy_register_fixed_link().
Convert the two drivers that care to deregister their fixed-link PHYs to
use the new helper, but note that most drivers currently fail to do so.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to drop the reference taken by of_parse_phandle() before
returning from dsa_slave_phy_setup().
Note that this also modifies the PHY priority so that any fixed-link
node is only parsed when no phy-handle is given, which is in accordance
with the common scheme for this.
Fixes: 0d8bcdd383 ("net: dsa: allow for more complex PHY setups")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
As it may get stale and lead to use after free.
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Alexander Duyck <aduyck@mirantis.com>
Cc: Andrey Konovalov <andreyknvl@google.com>
Fixes: cbc53e08a7 ("GSO: Add GSO type for fixed IPv4 ID")
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Be symmetric to hashtable insert and remove filter from hashtable only
in case skip sw flag is not set.
Fixes: e69985c67c ("net/sched: cls_flower: Introduce support in SKIP SW flag")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Amir Vadai <amir@vadai.me>
Signed-off-by: David S. Miller <davem@davemloft.net>
pskb_may_pull() can reallocate skb->head, we need to reload dh pointer
in dccp_invalid_packet() or risk use after free.
Bug found by Andrey Konovalov using syzkaller.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cb->done interface expects to be called in process context.
This was broken by the netlink RCU conversion. This patch fixes
it by adding a worker struct to make the cb->done call where
necessary.
Fixes: 21e4902aea ("netlink: Lockless lookup with RCU grace...")
Reported-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a validation function to make sure offset is valid:
1. Not below skb head (could happen when offset is negative).
2. Validate both 'offset' and 'at'.
Signed-off-by: Amir Vadai <amir@vadai.me>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clean up: offset and handle should be zero-filled, just like in the
chunk encoders.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Clean up: The convention for this type of warning message is not to
show the function name or "RPC: ".
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Clean up: This message was intended to be a dprintk, as it is on the
server-side.
Fixes: 87cfb9a0c8 ('xprtrdma: Client-side support for ...')
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Clean up: If reset fails, FRMRs are no longer abandoned, rather
they are released immediately. Update the comment to reflect this.
Fixes: 2ffc871a57 ('xprtrdma: Release orphaned MRs immediately')
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Clean up: After some recent updates, clarifications can be made to
the FRMR invalidation logic.
- Both the remote and local invalidation case mark the frmr INVALID,
so make that a common path.
- Manage the WR list more "tastefully" by replacing the conditional
that discriminates between the list head and ->next pointers.
- Use mw->mw_handle in all cases, since that has the same value as
f->fr_mr->rkey, and is already in cache.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Micro-optimization: Most of the time, calls to ro_unmap_safe are
expensive no-ops. Call only when there is work to do.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
> ** CID 114101: Error handling issues (CHECKED_RETURN)
> /net/sunrpc/xprtrdma/verbs.c: 355 in rpcrdma_create_id()
Commit 5675add36e ("RPC/RDMA: harden connection logic against
missing/late rdma_cm upcalls.") replaced wait_for_completion() calls
with these two call sites.
The original wait_for_completion() calls were added in the initial
commit of verbs.c, which was commit c56c65fb67 ("RPCRDMA: rpc rdma
verbs interface implementation"), but these returned void.
rpcrdma_create_id() is called by the RDMA connect worker, which
probably won't ever be interrupted. It is also called by
rpcrdma_ia_open which is in the synchronous mount path, and ^C is
possible there.
Add a bit of logic at those two call sites to return if the waits
return ERESTARTSYS.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
I noticed recently that during an xfstests on a krb5i mount, the
retransmit count for certain operations had gone negative, and the
backlog value became unreasonably large. I recall that Andy has
pointed this out to me in the past.
When call_refresh fails to find a valid credential for an RPC, the
RPC exits immediately without sending anything on the wire. This
leaves rq_ntrans, rq_xtime, and rq_rtt set to zero.
The solution for om_queue is to not add the to RPC's running backlog
queue total whenever rq_xtime is zero.
For om_ntrans, it's a bit more difficult. A zero rq_ntrans causes
om_ops to become larger than om_ntrans. The design of the RPC
metrics API assumes that ntrans will always be equal to or larger
than the ops count. The result is that when an RPC fails to find
credentials, the RPC operation's reported retransmit count, which is
computed in user space as the difference between ops and ntrans,
goes negative.
Ideally the kernel API should report a separate retransmit and
"exited before initial transmission" metric, so that user space can
sort out the difference properly.
To avoid kernel API changes and changes to the way rq_ntrans is used
when performing transport locking, account for untransmitted RPCs
so that om_ntrans keeps up with om_ops: always add one or more to
om_ntrans.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Some devices (such as the Mellanox CX-4) can register, under a
single R_key, a set of memory regions that are not contiguous. When
this is done, all the segments in a Reply list, say, can then be
invalidated in a single LocalInv Work Request (or via Remote
Invalidation, which can invalidate exactly one R_key when completing
a Receive).
This means a single FastReg WR is used to register, and one or zero
LocalInv WRs can invalidate, the memory involved with RDMA transfers
on behalf of an RPC.
In addition, xprtrdma constructs some Reply chunks from three or
more segments. By registering them with SG_GAP, only one segment
is needed for the Reply chunk, allowing the whole chunk to be
invalidated remotely.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Verbs providers may perform house-keeping on the Send Queue during
each signaled send completion. It is necessary therefore for a verbs
consumer (like xprtrdma) to occasionally force a signaled send
completion if it runs unsignaled most of the time.
xprtrdma does not require signaled completions for Send or FastReg
Work Requests, but does signal some LocalInv Work Requests. To
ensure that Send Queue house-keeping can run before the Send Queue
is more than half-consumed, xprtrdma forces a signaled completion
on occasion by counting the number of Send Queue Entries it
consumes. It currently does this by counting each ib_post_send as
one Entry.
Commit c9918ff56d ("xprtrdma: Add ro_unmap_sync method for FRWR")
introduced the ability for frwr_op_unmap_sync to post more than one
Work Request with a single post_send. Thus the underlying assumption
of one Send Queue Entry per ib_post_send is no longer true.
Also, FastReg Work Requests are currently never signaled. They
should be signaled once in a while, just as Send is, to keep the
accounting of consumed SQEs accurate.
While we're here, convert the CQCOUNT macros to the currently
preferred kernel coding style, which is inline functions.
Fixes: c9918ff56d ("xprtrdma: Add ro_unmap_sync method for FRWR")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
When the inline threshold size is set to large values (say, 32KB)
any NFSv4.1 CB request from the server gets a reply with status
NFS4ERR_RESOURCE.
Looks like there are some upper layer assumptions about the maximum
size of a reply (for example, in process_op). Cap the size of the
NFSv4 client's reply resources at a page.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Dmitry Vyukov reported GPF in network stack that Andrey traced down to
negative nh offset in nf_ct_frag6_queue().
Problem is that all network headers before fragment header are pulled.
Normal ipv6 reassembly will drop the skb when errors occur further down
the line.
netfilter doesn't do this, and instead passed the original fragment
along. That was also fine back when netfilter ipv6 defrag worked with
cloned fragments, as the original, pristine fragment was passed on.
So we either have to undo the pull op, or discard such fragments.
Since they're malformed after all (e.g. overlapping fragment) it seems
preferrable to just drop them.
Same for temporary errors -- it doesn't make sense to accept (and
perhaps forward!) only some fragments of same datagram.
Fixes: 029f7f3b87 ("netfilter: ipv6: nf_defrag: avoid/free clone operations")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Debugged-by: Andrey Konovalov <andreyknvl@google.com>
Diagnosed-by: Eric Dumazet <Eric Dumazet <edumazet@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
_dsa_register_switch() gets a dsa_switch_tree object either via
dsa_get_dst() or via dsa_add_dst(). Former path does not increase kref
in returned object (resulting into caller not owning a reference),
while later path does create a new object (resulting into caller owning
a reference).
The rest of _dsa_register_switch() assumes that it owns a reference, and
calls dsa_put_dst().
This causes a memory breakage if first switch in the tree initialized
successfully, but second failed to initialize. In particular, freed
dsa_swith_tree object is left referenced by switch that was initialized,
and later access to sysfs attributes of that switch cause OOPS.
To fix, need to add kref_get() call to dsa_get_dst().
Fixes: 83c0afaec7 ("net: dsa: Add new binding implementation")
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrey reported the following while fuzzing the kernel with syzkaller:
kasan: CONFIG_KASAN_INLINE enabled
kasan: GPF could be caused by NULL-ptr deref or user memory access
general protection fault: 0000 [#1] SMP KASAN
Modules linked in:
CPU: 0 PID: 3859 Comm: a.out Not tainted 4.9.0-rc6+ #429
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
task: ffff8800666d4200 task.stack: ffff880067348000
RIP: 0010:[<ffffffff833617ec>] [<ffffffff833617ec>]
icmp6_send+0x5fc/0x1e30 net/ipv6/icmp.c:451
RSP: 0018:ffff88006734f2c0 EFLAGS: 00010206
RAX: ffff8800666d4200 RBX: 0000000000000000 RCX: 0000000000000000
RDX: 0000000000000000 RSI: dffffc0000000000 RDI: 0000000000000018
RBP: ffff88006734f630 R08: ffff880064138418 R09: 0000000000000003
R10: dffffc0000000000 R11: 0000000000000005 R12: 0000000000000000
R13: ffffffff84e7e200 R14: ffff880064138484 R15: ffff8800641383c0
FS: 00007fb3887a07c0(0000) GS:ffff88006cc00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000020000000 CR3: 000000006b040000 CR4: 00000000000006f0
Stack:
ffff8800666d4200 ffff8800666d49f8 ffff8800666d4200 ffffffff84c02460
ffff8800666d4a1a 1ffff1000ccdaa2f ffff88006734f498 0000000000000046
ffff88006734f440 ffffffff832f4269 ffff880064ba7456 0000000000000000
Call Trace:
[<ffffffff83364ddc>] icmpv6_param_prob+0x2c/0x40 net/ipv6/icmp.c:557
[< inline >] ip6_tlvopt_unknown net/ipv6/exthdrs.c:88
[<ffffffff83394405>] ip6_parse_tlv+0x555/0x670 net/ipv6/exthdrs.c:157
[<ffffffff8339a759>] ipv6_parse_hopopts+0x199/0x460 net/ipv6/exthdrs.c:663
[<ffffffff832ee773>] ipv6_rcv+0xfa3/0x1dc0 net/ipv6/ip6_input.c:191
...
icmp6_send / icmpv6_send is invoked for both rx and tx paths. In both
cases the dst->dev should be preferred for determining the L3 domain
if the dst has been set on the skb. Fallback to the skb->dev if it has
not. This covers the case reported here where icmp6_send is invoked on
Rx before the route lookup.
Fixes: 5d41ce29e ("net: icmp6_send should use dst dev to determine L3 domain")
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula suggested to use explicit labels for clean up in the error path
instead of one `out_free' label, which handles multiple exits, introduced
in commit 38b482929e ("net/iucv: Convert to hotplug state machine").
Suggested-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: linux-s390@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: rt@linutronix.de
Cc: "David S. Miller" <davem@davemloft.net>
Link: http://lkml.kernel.org/r/20161124161013.dukr42y2nwscosk6@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Roi reported a crash in flower where tp->root was NULL in ->classify()
callbacks. Reason is that in ->destroy() tp->root is set to NULL via
RCU_INIT_POINTER(). It's problematic for some of the classifiers, because
this doesn't respect RCU grace period for them, and as a result, still
outstanding readers from tc_classify() will try to blindly dereference
a NULL tp->root.
The tp->root object is strictly private to the classifier implementation
and holds internal data the core such as tc_ctl_tfilter() doesn't know
about. Within some classifiers, such as cls_bpf, cls_basic, etc, tp->root
is only checked for NULL in ->get() callback, but nowhere else. This is
misleading and seemed to be copied from old classifier code that was not
cleaned up properly. For example, d3fa76ee6b ("[NET_SCHED]: cls_basic:
fix NULL pointer dereference") moved tp->root initialization into ->init()
routine, where before it was part of ->change(), so ->get() had to deal
with tp->root being NULL back then, so that was indeed a valid case, after
d3fa76ee6b, not really anymore. We used to set tp->root to NULL long
ago in ->destroy(), see 47a1a1d4be ("pkt_sched: remove unnecessary xchg()
in packet classifiers"); but the NULLifying was reintroduced with the
RCUification, but it's not correct for every classifier implementation.
In the cases that are fixed here with one exception of cls_cgroup, tp->root
object is allocated and initialized inside ->init() callback, which is always
performed at a point in time after we allocate a new tp, which means tp and
thus tp->root was not globally visible in the tp chain yet (see tc_ctl_tfilter()).
Also, on destruction tp->root is strictly kfree_rcu()'ed in ->destroy()
handler, same for the tp which is kfree_rcu()'ed right when we return
from ->destroy() in tcf_destroy(). This means, the head object's lifetime
for such classifiers is always tied to the tp lifetime. The RCU callback
invocation for the two kfree_rcu() could be out of order, but that's fine
since both are independent.
Dropping the RCU_INIT_POINTER(tp->root, NULL) for these classifiers here
means that 1) we don't need a useless NULL check in fast-path and, 2) that
outstanding readers of that tp in tc_classify() can still execute under
respect with RCU grace period as it is actually expected.
Things that haven't been touched here: cls_fw and cls_route. They each
handle tp->root being NULL in ->classify() path for historic reasons, so
their ->destroy() implementation can stay as is. If someone actually
cares, they could get cleaned up at some point to avoid the test in fast
path. cls_u32 doesn't set tp->root to NULL. For cls_rsvp, I just added a
!head should anyone actually be using/testing it, so it at least aligns with
cls_fw and cls_route. For cls_flower we additionally need to defer rhashtable
destruction (to a sleepable context) after RCU grace period as concurrent
readers might still access it. (Note that in this case we need to hold module
reference to keep work callback address intact, since we only wait on module
unload for all call_rcu()s to finish.)
This fixes one race to bring RCU grace period guarantees back. Next step
as worked on by Cong however is to fix 1e052be69d ("net_sched: destroy
proto tp when all filters are gone") to get the order of unlinking the tp
in tc_ctl_tfilter() for the RTM_DELTFILTER case right by moving
RCU_INIT_POINTER() before tcf_destroy() and let the notification for
removal be done through the prior ->delete() callback. Both are independant
issues. Once we have that right, we can then clean tp->root up for a number
of classifiers by not making them RCU pointers, which requires a new callback
(->uninit) that is triggered from tp's RCU callback, where we just kfree()
tp->root from there.
Fixes: 1f947bf151 ("net: sched: rcu'ify cls_bpf")
Fixes: 9888faefe1 ("net: sched: cls_basic use RCU")
Fixes: 70da9f0bf9 ("net: sched: cls_flow use RCU")
Fixes: 77b9900ef5 ("tc: introduce Flower classifier")
Fixes: bf3994d2ed ("net/sched: introduce Match-all classifier")
Fixes: 952313bd62 ("net: sched: cls_cgroup use RCU")
Reported-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: Roi Dayan <roid@mellanox.com>
Cc: Jiri Pirko <jiri@mellanox.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit dcf800344a ("net/sched: act_mirred: Refactor detection whether
dev needs xmit at mac header") added dev_is_mac_header_xmit(); since it's
also useful elsewhere, move it to if_arp.h and reuse it for BPF.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
After setup we don't need to keep user space fd number around anymore, as
it also has no useful meaning for anyone, just remove it.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit e4bf4f7696 ("tipc: simplify packet sequence number
handling") we changed the internal representation of the packet
sequence number counters from u32 to u16, reflecting what is really
sent over the wire.
Since then some link statistics counters have been displaying incorrect
values, partially because the counters meant to be used as sequence
number snapshots are now used as direct counters, stored as u32, and
partially because some counter updates are just missing in the code.
In this commit we correct this in two ways. First, we base the
displayed packet sent/received values on direct counters instead
of as previously a calculated difference between current sequence
number and a snapshot. Second, we add the missing updates of the
counters.
This change is compatible with the current netlink API, and requires
no changes to the user space tools.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Major changes:
iwlwifi
* finalize and enable dynamic queue allocation
* use dev_coredumpmsg() to prevent locking the driver
* small fix to pass the AID to the FW
* use FW PS decisions with multi-queue
ath9k
* add device tree bindings
* switch to use mac80211 intermediate software queues to reduce
latency and fix bufferbloat
wl18xx
* allow scanning in AP mode
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJYOAC4AAoJEG4XJFUm622bUYkH/3SSYp6moSdKpVnVPx7ST7yK
t9WHR9IMZFIhD6vq8AK6+8OQr1TgGjHfPu+WZj7CIl8nu53kcgPRi51gg1mndbNg
9N3RbVp06nGbM2VnW8ZIpg3OLIXatZ4c9g3LFvvtyobYvWGJ6W4D79JdlmTG1ELr
XAjInbxFsgon+CwqCMOaAJx8xYp42rBnPRZZvhOq9O33kRw8Umo9UQw0s1U2Vfgx
prxQ6d0GxNAPEe8QiDw/vtBcXWFMOhQeDl8sK70ZcojSn1FY730NsIh/Y86PcQTK
6TsvOL5gg+rd0ln8TZRAslnDrZBAhTEDqUzLQMRJ9VjEj5RFd8eLCSIzHfaroI8=
=4qCH
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2016-11-25' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.10
Major changes:
iwlwifi
* finalize and enable dynamic queue allocation
* use dev_coredumpmsg() to prevent locking the driver
* small fix to pass the AID to the FW
* use FW PS decisions with multi-queue
ath9k
* add device tree bindings
* switch to use mac80211 intermediate software queues to reduce
latency and fix bufferbloat
wl18xx
* allow scanning in AP mode
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net): ipsec 2016-11-25
1) Fix a refcount leak in vti6.
From Nicolas Dichtel.
2) Fix a wrong if statement in xfrm_sk_policy_lookup.
From Florian Westphal.
3) The flowcache watermarks are per cpu. Take this into
account when comparing to the threshold where we
refusing new allocations. From Miroslav Urbanek.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to drop the reference taken by of_phy_find_device() when
registering and deregistering the fixed-link PHY-device.
Fixes: 39b0c70519 ("net: dsa: Allow configuration of CPU & DSA port
speeds/duplex")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
udplite conflict is resolved by taking what 'net-next' did
which removed the backlog receive method assignment, since
it is no longer necessary.
Two entries were added to the non-priv ethtool operations
switch statement, one in 'net' and one in 'net-next, so
simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 10724cc7bb ("tipc: redesign connection-level flow control")
we replaced the previous message based flow control with one based on
1k blocks. In order to ensure backwards compatibility the mechanism
falls back to using message as base unit when it senses that the peer
doesn't support the new algorithm. The default flow control window,
i.e., how many units can be sent before the sender blocks and waits
for an acknowledge (aka advertisement) is 512. This was tested against
the previous version, which uses an acknowledge frequency of on ack per
256 received message, and found to work fine.
However, we missed the fact that versions older than Linux 3.15 use an
acknowledge frequency of 512, which is exactly the limit where a 4.6+
sender will stop and wait for acknowledge. This would also work fine if
it weren't for the fact that if the first sent message on a 4.6+ server
side is an empty SYNACK, this one is also is counted as a sent message,
while it is not counted as a received message on a legacy 3.15-receiver.
This leads to the sender always being one step ahead of the receiver, a
scenario causing the sender to block after 512 sent messages, while the
receiver only has registered 511 read messages. Hence, the legacy
receiver is not trigged to send an acknowledge, with a permanently
blocked sender as result.
We solve this deadlock by simply allowing the sender to send one more
message before it blocks, i.e., by a making minimal change to the
condition used for determining connection congestion.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ETHTOOL_GLINKSETTINGS command is deprecating the ETHTOOL_GSET
command and likewise it shouldn't require the CAP_NET_ADMIN capability.
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 35c55c9877 ("tipc: add neighbor monitoring framework") we
added a data area to the link monitor STATE messages under the
assumption that previous versions did not use any such data area.
For versions older than Linux 4.3 this assumption is not correct. In
those version, all STATE messages sent out from a node inadvertently
contain a 16 byte data area containing a string; -a leftover from
previous RESET messages which were using this during the setup phase.
This string serves no purpose in STATE messages, and should no be there.
Unfortunately, this data area is delivered to the link monitor
framework, where a sanity check catches that it is not a correct domain
record, and drops it. It also issues a rate limited warning about the
event.
Since such events occur much more frequently than anticipated, we now
choose to remove the warning in order to not fill the kernel log with
useless contents. We also make the sanity check stricter, to further
reduce the risk that such data is inavertently admitted.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 817298102b ("tipc: fix link priority propagation") introduced a
compatibility problem between TIPC versions newer than Linux 4.6 and
those older than Linux 4.4. In versions later than 4.4, link STATE
messages only contain a non-zero link priority value when the sender
wants the receiver to change its priority. This has the effect that the
receiver resets itself in order to apply the new priority. This works
well, and is consistent with the said commit.
However, in versions older than 4.4 a valid link priority is present in
all sent link STATE messages, leading to cyclic link establishment and
reset on the 4.6+ node.
We fix this by adding a test that the received value should not only
be valid, but also differ from the current value in order to cause the
receiving link endpoint to reset.
Reported-by: Amar Nv <amar.nv005@gmail.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Typical NAPI drivers use napi_consume_skb(skb) at TX completion time.
This put skb in a percpu special queue, napi_alloc_cache, to get bulk
frees.
It turns out the queue is not flushed and hits the NAPI_SKB_CACHE_SIZE
limit quite often, with skbs that were queued hundreds of usec earlier.
I measured this can take ~6000 nsec to perform one flush.
__kfree_skb_flush() can be called from two points right now :
1) From net_tx_action(), but only for skbs that were queued to
sd->completion_queue.
-> Irrelevant for NAPI drivers in normal operation.
2) From net_rx_action(), but only under high stress or if RPS/RFS has a
pending action.
This patch changes net_rx_action() to perform the flush in all cases and
after more urgent operations happened (like kicking remote CPUS for
RPS/RFS).
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jesper Dangaard Brouer <brouer@redhat.com>
Cc: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the cgroup associated with the receiving socket has an eBPF
programs installed, run them from ip_output(), ip6_output() and
ip_mc_output(). From mentioned functions we have two socket contexts
as per 7026b1ddb6 ("netfilter: Pass socket pointer down through
okfn()."). We explicitly need to use sk instead of skb->sk here,
since otherwise the same program would run multiple times on egress
when encap devices are involved, which is not desired in our case.
eBPF programs used in this context are expected to either return 1 to
let the packet pass, or != 1 to drop them. The programs have access to
the skb through bpf_skb_load_bytes(), and the payload starts at the
network headers (L3).
Note that cgroup_bpf_run_filter() is stubbed out as static inline nop
for !CONFIG_CGROUP_BPF, and is otherwise guarded by a static key if
the feature is unused.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the cgroup associated with the receiving socket has an eBPF
programs installed, run them from sk_filter_trim_cap().
eBPF programs used in this context are expected to either return 1 to
let the packet pass, or != 1 to drop them. The programs have access to
the skb through bpf_skb_load_bytes(), and the payload starts at the
network headers (L3).
Note that cgroup_bpf_run_filter() is stubbed out as static inline nop
for !CONFIG_CGROUP_BPF, and is otherwise guarded by a static key if
the feature is unused.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This program type is similar to BPF_PROG_TYPE_SOCKET_FILTER, except that
it does not allow BPF_LD_[ABS|IND] instructions and hooks up the
bpf_skb_load_bytes() helper.
Programs of this type will be attached to cgroups for network filtering
and accounting.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEES2FAuYbJvAGobdVQPTuqJaypJWoFAlg1ppETHG1rbEBwZW5n
dXRyb25peC5kZQAKCRA9O6olrKklaqieB/4o9PaD8Rj38Piy7lJW1ahAxoUnY4AA
Vu1eFvtidUswO5RV6mDOuqhTulzrMcPQZguW/S7eLZh6hWYVVLlgkrNLj/RpMXsH
rqGRC/sL5ICL1q/ijYK6NJJ3+GFQhl92gG+wJxsQfETWVDKH13N3sWcEyBh0+C5P
lnPFNVDVSy4bpkEgXAN/sfAvoHzW//34cnxTzlsd1COAWlxZ+HHgBAGp4kaYTpbF
Vz3kuNPfDI7U+36quE8SUXe/R9HfqQBtfbFtaxha8vqH8Fw6MJYO0BUJVmtawTDq
nBFvB/x+d0n1YeOgo5UD5bW9thItF57GEscWqYpTuhZ0jlPr5+CZeo14
=FImK
-----END PGP SIGNATURE-----
Merge tag 'linux-can-fixes-for-4.9-20161123' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2016-11-23
this is a pull request for net/master.
The patch by Oliver Hartkopp for the broadcast manager (bcm) fixes the
CAN-FD support, which may cause an out-of-bounds access otherwise.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth 2016-11-23
Sorry about the late pull request for 4.9, but we have one more
important Bluetooth patch that should make it to the release. It fixes
connection creation for Bluetooth LE controllers that do not have a
public address (only a random one).
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Should pass valid filter handle, not the netlink flags.
Fixes: 30a391a13a ("net sched filters: pass netlink message flags in event notification")
Signed-off-by: Roman Mashak <mrv@mojatatu.com>
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Reported-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHY drivers should be able to rely on the caller of {get,set}_tunable to
have acquired the PHY device mutex, in order to both serialize against
concurrent calls of these functions, but also against PHY state machine
changes. All ethtool PHY-level functions do this, except
{get,set}_tunable, so we make them consistent here as well.
We need to update the Microsemi PHY driver in the same commit to avoid
introducing either deadlocks, or lack of proper locking.
Fixes: 968ad9da7e ("ethtool: Implements ETHTOOL_PHY_GTUNABLE/ETHTOOL_PHY_STUNABLE")
Fixes: 310d9ad57a ("net: phy: Add downshift get/set support in Microsemi PHYs driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Allan W. Nielsen <allan.nielsen@microsemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some HWs need the VF driver to put part of the packet headers on the
TX descriptor so the e-switch can do proper matching and steering.
The supported modes: none, link, network, transport.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some drivers would need to check few internal matters for
that. To be used in downstream mlx5 commit.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commits 93821778de ("udp: Fix rcv socket locking") and
f7ad74fef3 ("net/ipv6/udp: UDP encapsulation: break backlog_rcv into
__udpv6_queue_rcv_skb") UDP backlog handlers were renamed, but UDPlite
was forgotten.
This leads to crashes if UDPlite header is pulled twice, which happens
starting from commit e6afc8ace6 ("udp: remove headers from UDP packets
before queueing")
Bug found by syzkaller team, thanks a lot guys !
Note that backlog use in UDP/UDPlite is scheduled to be removed starting
from linux-4.10, so this patch is only needed up to linux-4.9
Fixes: 93821778de ("udp: Fix rcv socket locking")
Fixes: f7ad74fef3 ("net/ipv6/udp: UDP encapsulation: break backlog_rcv into __udpv6_queue_rcv_skb")
Fixes: e6afc8ace6 ("udp: remove headers from UDP packets before queueing")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Cc: Benjamin LaHaise <bcrl@kvack.org>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an ipv6 address has the tentative flag set, it can't be
used as source for egress traffic, while the associated route,
if any, can be looked up and even stored into some dst_cache.
In the latter scenario, the source ipv6 address selected and
stored in the cache is most probably wrong (e.g. with
link-local scope) and the entity using the dst_cache will
experience lack of ipv6 connectivity until said cache is
cleared or invalidated.
Overall this may cause lack of connectivity over most IPv6 tunnels
(comprising geneve and vxlan), if the first egress packet reaches
the tunnel before the DaD is completed for the used ipv6
address.
This patch bumps a new genid after that the IFA_F_TENTATIVE flag
is cleared, so that dst_cache will be invalidated on
next lookup and ipv6 connectivity restored.
Fixes: 0c1d70af92 ("net: use dst_cache for vxlan device")
Fixes: 468dfffcd7 ("geneve: add dst caching support")
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VMware VMCI transport supports loopback inside virtual machines.
This patch implements loopback for virtio-vsock.
Flow control is handled by the virtio-vsock protocol as usual. The
sending process stops transmitting on a connection when the peer's
receive buffer space is exhausted.
Cathy Avery <cavery@redhat.com> noticed this difference between VMCI and
virtio-vsock when a test case using loopback failed. Although loopback
isn't the main point of AF_VSOCK, it is useful for testing and
virtio-vsock must match VMCI semantics so that userspace programs run
regardless of the underlying transport.
My understanding is that loopback is not supported on the host side with
VMCI. Follow that by implementing it only in the guest driver, not the
vhost host driver.
Cc: Jorgen Hansen <jhansen@vmware.com>
Reported-by: Cathy Avery <cavery@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Otherwise, kernel panic will happen if the user does not specify
the related attributes.
Fixes: 0f3cd9b369 ("netfilter: nf_tables: add range expression")
Signed-off-by: Liping Zhang <zlpnobody@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
As Liping Zhang reports, after commit a8b1e36d0d ("netfilter: nft_dynset:
fix element timeout for HZ != 1000"), priv->timeout was stored in jiffies,
while set->timeout was stored in milliseconds. This is inconsistent and
incorrect.
Firstly, we already call msecs_to_jiffies in nft_set_elem_init, so
priv->timeout will be converted to jiffies twice.
Secondly, if the user did not specify the NFTA_DYNSET_TIMEOUT attr,
set->timeout will be used, but we forget to call msecs_to_jiffies
when do update elements.
Fix this by using jiffies internally for traditional sets and doing the
conversions to/from msec when interacting with userspace - as dynset
already does.
This is preferable to doing the conversions, when elements are inserted or
updated, because this can happen very frequently on busy dynsets.
Fixes: a8b1e36d0d ("netfilter: nft_dynset: fix element timeout for HZ != 1000")
Reported-by: Liping Zhang <zlpnobody@gmail.com>
Signed-off-by: Anders K. Pedersen <akp@cohaesio.com>
Acked-by: Liping Zhang <zlpnobody@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
I got offlist bug report about failing connections and high cpu usage.
This happens because we hit 'elasticity' checks in rhashtable that
refuses bucket list exceeding 16 entries.
The nat bysrc hash unfortunately needs to insert distinct objects that
share same key and are identical (have same source tuple), this cannot
be avoided.
Switch to the rhlist interface which is designed for this.
The nulls_base is removed here, I don't think its needed:
A (unlikely) false positive results in unneeded port clash resolution,
a false negative results in packet drop during conntrack confirmation,
when we try to insert the duplicate into main conntrack hash table.
Tested by adding multiple ip addresses to host, then adding
iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE
... and then creating multiple connections, from same source port but
different addresses:
for i in $(seq 2000 2032);do nc -p 1234 192.168.7.1 $i > /dev/null & done
(all of these then get hashed to same bysource slot)
Then, to test that nat conflict resultion is working:
nc -s 10.0.0.1 -p 1234 192.168.7.1 2000
nc -s 10.0.0.2 -p 1234 192.168.7.1 2000
tcp .. src=10.0.0.1 dst=192.168.7.1 sport=1234 dport=2000 src=192.168.7.1 dst=192.168.7.10 sport=2000 dport=1024 [ASSURED]
tcp .. src=10.0.0.2 dst=192.168.7.1 sport=1234 dport=2000 src=192.168.7.1 dst=192.168.7.10 sport=2000 dport=1025 [ASSURED]
tcp .. src=192.168.7.10 dst=192.168.7.1 sport=1234 dport=2000 src=192.168.7.1 dst=192.168.7.10 sport=2000 dport=1234 [ASSURED]
tcp .. src=192.168.7.10 dst=192.168.7.1 sport=1234 dport=2001 src=192.168.7.1 dst=192.168.7.10 sport=2001 dport=1234 [ASSURED]
[..]
-> nat altered source ports to 1024 and 1025, respectively.
This can also be confirmed on destination host which shows
ESTAB 0 0 192.168.7.1:2000 192.168.7.10:1024
ESTAB 0 0 192.168.7.1:2000 192.168.7.10:1025
ESTAB 0 0 192.168.7.1:2000 192.168.7.10:1234
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Fixes: 870190a9ec ("netfilter: nat: convert nat bysrc hash to rhashtable")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The comparator works like memcmp, i.e. 0 means objects are equal.
In other words, when objects are distinct they are treated as identical,
when they are distinct they are allegedly the same.
The first case is rare (distinct objects are unlikely to get hashed to
same bucket).
The second case results in unneeded port conflict resolutions attempts.
Fixes: 870190a9ec ("netfilter: nat: convert nat bysrc hash to rhashtable")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Use the function nft_parse_u32_check() to fetch the value and validate
the u32 attribute into the hash len u8 field.
This patch revisits 4da449ae1d ("netfilter: nft_exthdr: Add size check
on u8 nft_exthdr attributes").
Fixes: cb1b69b0b1 ("netfilter: nf_tables: add hash expression")
Signed-off-by: Laura Garcia Liebana <nevola@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
nf_send_reset6 is not considering the L3 domain and lookups are sent
to the wrong table. For example consider the following output rule:
ip6tables -A OUTPUT -p tcp --dport 12345 -j REJECT --reject-with tcp-reset
using perf to analyze lookups via the fib6_table_lookup tracepoint shows:
swapper 0 [001] 248.787816: fib6:fib6_table_lookup: table 255 oif 0 iif 1 src 2100:1::3 dst 2100:1:
ffffffff81439cdc perf_trace_fib6_table_lookup ([kernel.kallsyms])
ffffffff814c1ce3 trace_fib6_table_lookup ([kernel.kallsyms])
ffffffff814c3e89 ip6_pol_route ([kernel.kallsyms])
ffffffff814c40d5 ip6_pol_route_output ([kernel.kallsyms])
ffffffff814e7b6f fib6_rule_action ([kernel.kallsyms])
ffffffff81437f60 fib_rules_lookup ([kernel.kallsyms])
ffffffff814e7c79 fib6_rule_lookup ([kernel.kallsyms])
ffffffff814c2541 ip6_route_output_flags ([kernel.kallsyms])
528 nf_send_reset6 ([nf_reject_ipv6])
The lookup is directed to table 255 rather than the table associated with
the device via the L3 domain. Update nf_send_reset6 to pull the L3 domain
from the dst currently attached to the skb.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
ip_route_me_harder is not considering the L3 domain and sending lookups
to the wrong table. For example consider the following output rule:
iptables -I OUTPUT -p tcp --dport 12345 -j REJECT --reject-with tcp-reset
using perf to analyze lookups via the fib_table_lookup tracepoint shows:
vrf-test 1187 [001] 46887.295927: fib:fib_table_lookup: table 255 oif 0 iif 0 src 0.0.0.0 dst 10.100.1.254 tos 0 scope 0 flags 0
ffffffff8143922c perf_trace_fib_table_lookup ([kernel.kallsyms])
ffffffff81493aac fib_table_lookup ([kernel.kallsyms])
ffffffff8148dda3 __inet_dev_addr_type ([kernel.kallsyms])
ffffffff8148ddf6 inet_addr_type ([kernel.kallsyms])
ffffffff8149e344 ip_route_me_harder ([kernel.kallsyms])
and
vrf-test 1187 [001] 46887.295933: fib:fib_table_lookup: table 255 oif 0 iif 1 src 10.100.1.254 dst 10.100.1.2 tos 0 scope 0 flags
ffffffff8143922c perf_trace_fib_table_lookup ([kernel.kallsyms])
ffffffff81493aac fib_table_lookup ([kernel.kallsyms])
ffffffff814998ff fib4_rule_action ([kernel.kallsyms])
ffffffff81437f35 fib_rules_lookup ([kernel.kallsyms])
ffffffff81499758 __fib_lookup ([kernel.kallsyms])
ffffffff8144f010 fib_lookup.constprop.34 ([kernel.kallsyms])
ffffffff8144f759 __ip_route_output_key_hash ([kernel.kallsyms])
ffffffff8144fc6a ip_route_output_flow ([kernel.kallsyms])
ffffffff8149e39b ip_route_me_harder ([kernel.kallsyms])
In both cases the lookups are directed to table 255 rather than the
table associated with the device via the L3 domain. Update both
lookups to pull the L3 domain from the dst currently attached to the
skb.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This reverts commit 7c6ae610a1, because l2tp_xmit_skb() never
returns NET_XMIT_CN, it ignores the return value of l2tp_xmit_core().
Cc: Gao Feng <gfree.wind@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For RT netlink, calcit() function should return the minimal size for
netlink dump message. This will make sure that dump message for every
network device can be stored.
Currently, rtnl_calcit() function doesn't account the size of header of
netlink message, this patch will fix it.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 6f3b911d5f ("can: bcm: add support for CAN FD frames") the
CAN broadcast manager supports CAN and CAN FD data frames.
As these data frames are embedded in struct can[fd]_frames which have a
different length the access to the provided array of CAN frames became
dependend of op->cfsiz. By using a struct canfd_frame pointer for the array of
CAN frames the new offset calculation based on op->cfsiz was accidently applied
to CAN FD frame element lengths.
This fix makes the pointer to the arrays of the different CAN frame types a
void pointer so that the offset calculation in bytes accesses the correct CAN
frame elements.
Reference: http://marc.info/?l=linux-netdev&m=147980658909653
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The threshold for OOM protection is too small for systems with large
number of CPUs. Applications report ENOBUFs on connect() every 10
minutes.
The problem is that the variable net->xfrm.flow_cache_gc_count is a
global counter while the variable fc->high_watermark is a per-CPU
constant. Take the number of CPUs into account as well.
Fixes: 6ad3122a08 ("flowcache: Avoid OOM condition under preasure")
Reported-by: Lukáš Koldrt <lk@excello.cz>
Tested-by: Jan Hejl <jh@excello.cz>
Signed-off-by: Miroslav Urbanek <mu@miroslavurbanek.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Install the callbacks via the state machine and let the core invoke the
callbacks on the already online CPUs. The smp function calls in the
online/downprep callbacks are not required as the callback is guaranteed to
be invoked on the upcoming/outgoing cpu.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-s390@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: Ursula Braun <ubraun@linux.vnet.ibm.com>
Cc: rt@linuxtronix.de
Link: http://lkml.kernel.org/r/20161117183541.8588-13-bigeasy@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The hci_get_route() API is used to look up local HCI devices, however
so far it has been incapable of dealing with anything else than the
public address of HCI devices. This completely breaks with LE-only HCI
devices that do not come with a public address, but use a static
random address instead.
This patch exteds the hci_get_route() API with a src_type parameter
that's used for comparing with the right address of each HCI device.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Andre Noll reported panics after my recent fix (commit 34fad54c25
"net: __skb_flow_dissect() must cap its return value")
After some more headaches, Alexander root caused the problem to
init_default_flow_dissectors() being called too late, in case
a network driver like IGB is not a module and receives DHCP message
very early.
Fix is to call init_default_flow_dissectors() much earlier,
as it is a core infrastructure and does not depend on another
kernel service.
Fixes: 06635a35d1 ("flow_dissect: use programable dissector in skb_flow_dissect and friends")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andre Noll <maan@tuebingen.mpg.de>
Diagnosed-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All conflicts were simple overlapping changes except perhaps
for the Thunder driver.
That driver has a change_mtu method explicitly for sending
a message to the hardware. If that fails it returns an
error.
Normally a driver doesn't need an ndo_change_mtu method becuase those
are usually just range changes, which are now handled generically.
But since this extra operation is needed in the Thunder driver, it has
to stay.
However, if the message send fails we have to restore the original
MTU before the change because the entire call chain expects that if
an error is thrown by ndo_change_mtu then the MTU did not change.
Therefore code is added to nicvf_change_mtu to remember the original
MTU, and to restore it upon nicvf_update_hw_max_frs() failue.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Clear congestion control state when changing algorithms on an
existing socket, from Florian Westphal.
2) Fix register bit values in altr_tse_pcs portion of stmmac driver,
from Jia Jie Ho.
3) Fix PTP handling in stammc driver for GMAC4, from Giuseppe
CAVALLARO.
4) Fix udplite multicast delivery handling, it ignores the udp_table
parameter passed into the lookups, from Pablo Neira Ayuso.
5) Synchronize the space estimated by rtnl_vfinfo_size and the space
actually used by rtnl_fill_vfinfo. From Sabrina Dubroca.
6) Fix memory leak in fib_info when splitting nodes, from Alexander
Duyck.
7) If a driver does a napi_hash_del() explicitily and not via
netif_napi_del(), it must perform RCU synchronization as needed. Fix
this in virtio-net and bnxt drivers, from Eric Dumazet.
8) Likewise, it is not necessary to invoke napi_hash_del() is we are
also doing neif_napi_del() in the same code path. Remove such calls
from be2net and cxgb4 drivers, also from Eric Dumazet.
9) Don't allocate an ID in peernet2id_alloc() if the netns is dead,
from WANG Cong.
10) Fix OF node and device struct leaks in of_mdio, from Johan Hovold.
11) We cannot cache routes in ip6_tunnel when using inherited traffic
classes, from Paolo Abeni.
12) Fix several crashes and leaks in cpsw driver, from Johan Hovold.
13) Splice operations cannot use freezable blocking calls in AF_UNIX,
from WANG Cong.
14) Link dump filtering by master device and kind support added an error
in loop index updates during the dump if we actually do filter, fix
from Zhang Shengju.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (59 commits)
tcp: zero ca_priv area when switching cc algorithms
net: l2tp: Treat NET_XMIT_CN as success in l2tp_eth_dev_xmit
ethernet: stmmac: make DWMAC_STM32 depend on it's associated SoC
tipc: eliminate obsolete socket locking policy description
rtnl: fix the loop index update error in rtnl_dump_ifinfo()
l2tp: fix racy SOCK_ZAPPED flag check in l2tp_ip{,6}_bind()
net: macb: add check for dma mapping error in start_xmit()
rtnetlink: fix FDB size computation
netns: fix get_net_ns_by_fd(int pid) typo
af_unix: conditionally use freezable blocking calls in read
net: ethernet: ti: cpsw: fix fixed-link phy probe deferral
net: ethernet: ti: cpsw: add missing sanity check
net: ethernet: ti: cpsw: fix secondary-emac probe error path
net: ethernet: ti: cpsw: fix of_node and phydev leaks
net: ethernet: ti: cpsw: fix deferred probe
net: ethernet: ti: cpsw: fix mdio device reference leak
net: ethernet: ti: cpsw: fix bad register access in probe error path
net: sky2: Fix shutdown crash
cfg80211: limit scan results cache size
net sched filters: pass netlink message flags in event notification
...
The undo_cwnd fallback in the stack doubles cwnd based on ssthresh,
which un-does reno halving behaviour.
It seems more appropriate to let congctl algorithms pair .ssthresh
and .undo_cwnd properly. Add a 'tcp_reno_undo_cwnd' function and wire it
up for all congestion algorithms that used to rely on the fallback.
Cc: Eric Dumazet <edumazet@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
congestion control algorithms that do not halve cwnd in their .ssthresh
should provide a .cwnd_undo rather than rely on current fallback which
assumes reno halving (and thus doubles the cwnd).
All of these do 'something else' in their .ssthresh implementation, thus
store the cwnd on loss and provide .undo_cwnd to restore it again.
A followup patch will remove the fallback and all algorithms will
need to provide a .cwnd_undo function.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds basic support for MLDv2 queries, the default is MLDv1
as before. A new multicast option - multicast_mld_version, adds the
ability to change it between 1 and 2 via netlink and sysfs.
The MLD option is disabled if CONFIG_IPV6 is disabled.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds basic support for IGMPv3 queries, the default is IGMPv2
as before. A new multicast option - multicast_igmp_version, adds the
ability to change it between 2 and 3 via netlink and sysfs. The option
struct member is in a 4 byte hole in net_bridge.
There also a few minor style adjustments in br_multicast_new_group and
br_multicast_add_group.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to zero out the private data area when application switches
connection to different algorithm (TCP_CONGESTION setsockopt).
When congestion ops get assigned at connect time everything is already
zeroed because sk_alloc uses GFP_ZERO flag. But in the setsockopt case
this contains whatever previous cc placed there.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tc could return NET_XMIT_CN as one congestion notification, but
it does not mean the packe is lost. Other modules like ipvlan,
macvlan, and others treat NET_XMIT_CN as success too.
So l2tp_eth_dev_xmit should add the NET_XMIT_CN check.
Signed-off-by: Gao Feng <gfree.wind@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
UDP_SKB_CB(skb)->partial_cov is located at offset 66 in skb,
requesting a cold cache line being read in cpu cache.
We can avoid this cache line miss for UDP sockets,
as partial_cov has a meaning only for UDPLite.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The comment block in socket.c describing the locking policy is
obsolete, and does not reflect current reality. We remove it in this
commit.
Since the current locking policy is much simpler and follows a
mainstream approach, we see no need to add a new description.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the link is filtered out, loop index should also be updated. If not,
loop index will not be correct.
Fixes: dc599f76c2 ("net: Add support for filtering link dump by master device and kind")
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1) cast to "int" is unnecessary:
u8 will be promoted to int before decrementing,
small positive numbers fit into "int", so their values won't be changed
during promotion.
Once everything is int including loop counters, signedness doesn't
matter: 32-bit operations will stay 32-bit operations.
But! Someone tried to make this loop smart by making everything of
the same type apparently in an attempt to optimise it.
Do the optimization, just differently.
Do the cast where it matters. :^)
2) frag size is unsigned entity and sum of fragments sizes is also
unsigned.
Make everything unsigned, leave no MOVSX instruction behind.
add/remove: 0/0 grow/shrink: 0/3 up/down: 0/-4 (-4)
function old new delta
skb_cow_data 835 834 -1
ip_do_fragment 2549 2548 -1
ip6_fragment 3130 3128 -2
Total: Before=154865032, After=154865028, chg -0.00%
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
size_t is way too much for an integer not exceeding 64.
Space savings: 10 bytes!
add/remove: 0/0 grow/shrink: 0/3 up/down: 0/-10 (-10)
function old new delta
napi_consume_skb 165 163 -2
__kfree_skb_flush 56 53 -3
__kfree_skb_defer 97 92 -5
Total: Before=154865639, After=154865629, chg -0.00%
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- 6 patches adding functionality to detect a WiFi interface under
other virtual interfaces, like VLANs. They introduce a cache for
the detected the WiFi configuration to avoid RTNL locking in
critical sections. Patches have been prepared by Marek Lindner
and Sven Eckelmann
- Enable automatic module loading for genl requests, by Sven Eckelmann
- Fix a potential race condition on interface removal. This is not
happening very often in practice, but requires bigger changes to fix,
so we are sending this to net-next. By Linus Luessing
-----BEGIN PGP SIGNATURE-----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=Pdlv
-----END PGP SIGNATURE-----
Merge tag 'batadv-next-for-davem-20161119' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
This feature patchset includes the following changes:
- 6 patches adding functionality to detect a WiFi interface under
other virtual interfaces, like VLANs. They introduce a cache for
the detected the WiFi configuration to avoid RTNL locking in
critical sections. Patches have been prepared by Marek Lindner
and Sven Eckelmann
- Enable automatic module loading for genl requests, by Sven Eckelmann
- Fix a potential race condition on interface removal. This is not
happening very often in practice, but requires bigger changes to fix,
so we are sending this to net-next. By Linus Luessing
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
- Revert a splat on disabling interface which created another problem,
by Sven Eckelmann
- Fix error handling when the primary interface disappears during a
throughput meter test, by Sven Eckelmann
-----BEGIN PGP SIGNATURE-----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=DdJj
-----END PGP SIGNATURE-----
Merge tag 'batadv-net-for-davem-20161119' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
Here are two batman-adv bugfix patches:
- Revert a splat on disabling interface which created another problem,
by Sven Eckelmann
- Fix error handling when the primary interface disappears during a
throughput meter test, by Sven Eckelmann
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove static function __packet_rcv_vnet(), which only called
virtio_net_hdr_from_skb() and BUG()ged out if an error code was
returned. Instead, call virtio_net_hdr_from_skb() from the former
call sites of __packet_rcv_vnet() and actually use the error handling
code that is already there.
Signed-off-by: Jarno Rajahalme <jarno@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the common virtio_net_hdr_to_skb() instead of open coding it.
Other call sites were changed by commit fd2a0437dc, but this one was
missed, maybe because it is split in two parts of the source code.
Interim comparisons of 'vnet_hdr->gso_type' still work as both the
vnet_hdr and skb notion of gso_type is zero when there is no gso.
Fixes: fd2a0437dc ("virtio_net: introduce virtio_net_hdr_{from,to}_skb")
Signed-off-by: Jarno Rajahalme <jarno@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
virtio_net_hdr_from_skb() clears the memory for the header, so there
is no point for the callers to do the same.
Signed-off-by: Jarno Rajahalme <jarno@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----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=F2DQ
-----END PGP SIGNATURE-----
Merge tag 'nfsd-4.9-2' of git://linux-nfs.org/~bfields/linux
Pull nfsd bugfix from Bruce Fields:
"Just one fix for an NFS/RDMA crash"
* tag 'nfsd-4.9-2' of git://linux-nfs.org/~bfields/linux:
sunrpc: svc_age_temp_xprts_now should not call setsockopt non-tcp transports
Add missing NDA_VLAN attribute's size.
Fixes: 1e53d5bb88 ("net: Pass VLAN ID to rtnl_fdb_notify.")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
* limit # of scan results stored in memory - this is a long-standing bug
Jouni and I only noticed while discussing other things in Santa Fe
* revert AP_LINK_PS patch that was causing issues (Felix)
* various A-MSDU/A-MPDU fixes for TXQ code (Felix)
* interoperability workaround for peers with broken VHT capabilities
(Filip Matusiak)
* add bitrate definition for a VHT MCS that's supposed to be invalid
but gets used by some hardware anyway (Thomas Pedersen)
* beacon timer fix in hwsim (Benjamin Beichler)
-----BEGIN PGP SIGNATURE-----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=q2mI
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2016-11-18' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
A few more bugfixes:
* limit # of scan results stored in memory - this is a long-standing bug
Jouni and I only noticed while discussing other things in Santa Fe
* revert AP_LINK_PS patch that was causing issues (Felix)
* various A-MSDU/A-MPDU fixes for TXQ code (Felix)
* interoperability workaround for peers with broken VHT capabilities
(Filip Matusiak)
* add bitrate definition for a VHT MCS that's supposed to be invalid
but gets used by some hardware anyway (Thomas Pedersen)
* beacon timer fix in hwsim (Benjamin Beichler)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 2b15af6f95 ("af_unix: use freezable blocking calls in read")
converts schedule_timeout() to its freezable version, it was probably
correct at that time, but later, commit 2b514574f7
("net: af_unix: implement splice for stream af_unix sockets") breaks
the strong requirement for a freezable sleep, according to
commit 0f9548ca10:
We shouldn't try_to_freeze if locks are held. Holding a lock can cause a
deadlock if the lock is later acquired in the suspend or hibernate path
(e.g. by dpm). Holding a lock can also cause a deadlock in the case of
cgroup_freezer if a lock is held inside a frozen cgroup that is later
acquired by a process outside that group.
The pipe_lock is still held at that point.
So use freezable version only for the recvmsg call path, avoid impact for
Android.
Fixes: 2b514574f7 ("net: af_unix: implement splice for stream af_unix sockets")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Colin Cross <ccross@android.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding validation support for the ETHTOOL_PHY_DOWNSHIFT. Functional
implementation needs to be done in the individual PHY drivers.
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microsemi.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Allan W. Nielsen <allan.nielsen@microsemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding get_tunable/set_tunable function pointer to the phy_driver
structure, and uses these function pointers to implement the
ETHTOOL_PHY_GTUNABLE/ETHTOOL_PHY_STUNABLE ioctls.
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microsemi.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Allan W. Nielsen <allan.nielsen@microsemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make struct pernet_operations::id unsigned.
There are 2 reasons to do so:
1)
This field is really an index into an zero based array and
thus is unsigned entity. Using negative value is out-of-bound
access by definition.
2)
On x86_64 unsigned 32-bit data which are mixed with pointers
via array indexing or offsets added or subtracted to pointers
are preffered to signed 32-bit data.
"int" being used as an array index needs to be sign-extended
to 64-bit before being used.
void f(long *p, int i)
{
g(p[i]);
}
roughly translates to
movsx rsi, esi
mov rdi, [rsi+...]
call g
MOVSX is 3 byte instruction which isn't necessary if the variable is
unsigned because x86_64 is zero extending by default.
Now, there is net_generic() function which, you guessed it right, uses
"int" as an array index:
static inline void *net_generic(const struct net *net, int id)
{
...
ptr = ng->ptr[id - 1];
...
}
And this function is used a lot, so those sign extensions add up.
Patch snipes ~1730 bytes on allyesconfig kernel (without all junk
messing with code generation):
add/remove: 0/0 grow/shrink: 70/598 up/down: 396/-2126 (-1730)
Unfortunately some functions actually grow bigger.
This is a semmingly random artefact of code generation with register
allocator being used differently. gcc decides that some variable
needs to live in new r8+ registers and every access now requires REX
prefix. Or it is shifted into r12, so [r12+0] addressing mode has to be
used which is longer than [r8]
However, overall balance is in negative direction:
add/remove: 0/0 grow/shrink: 70/598 up/down: 396/-2126 (-1730)
function old new delta
nfsd4_lock 3886 3959 +73
tipc_link_build_proto_msg 1096 1140 +44
mac80211_hwsim_new_radio 2776 2808 +32
tipc_mon_rcv 1032 1058 +26
svcauth_gss_legacy_init 1413 1429 +16
tipc_bcbase_select_primary 379 392 +13
nfsd4_exchange_id 1247 1260 +13
nfsd4_setclientid_confirm 782 793 +11
...
put_client_renew_locked 494 480 -14
ip_set_sockfn_get 730 716 -14
geneve_sock_add 829 813 -16
nfsd4_sequence_done 721 703 -18
nlmclnt_lookup_host 708 686 -22
nfsd4_lockt 1085 1063 -22
nfs_get_client 1077 1050 -27
tcf_bpf_init 1106 1076 -30
nfsd4_encode_fattr 5997 5930 -67
Total: Before=154856051, After=154854321, chg -0.00%
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
UDP busy polling is restricted to connected UDP sockets.
This is because sk_busy_loop() only takes care of one NAPI context.
There are cases where it could be extended.
1) Some hosts receive traffic on a single NIC, with one RX queue.
2) Some applications use SO_REUSEPORT and associated BPF filter
to split the incoming traffic on one UDP socket per RX
queue/thread/cpu
3) Some UDP sockets are used to send/receive traffic for one flow, but
they do not bother with connect()
This patch records the napi_id of first received skb, giving more
reach to busy polling.
Tested:
lpaa23:~# echo 70 >/proc/sys/net/core/busy_read
lpaa24:~# echo 70 >/proc/sys/net/core/busy_read
lpaa23:~# for f in `seq 1 10`; do ./super_netperf 1 -H lpaa24 -t UDP_RR -l 5; done
Before patch :
27867 28870 37324 41060 41215
36764 36838 44455 41282 43843
After patch :
73920 73213 70147 74845 71697
68315 68028 75219 70082 73707
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's possible to make scanning consume almost arbitrary amounts
of memory, e.g. by sending beacon frames with random BSSIDs at
high rates while somebody is scanning.
Limit the number of BSS table entries we're willing to cache to
1000, limiting maximum memory usage to maybe 4-5MB, but lower
in practice - that would be the case for having both full-sized
beacon and probe response frames for each entry; this seems not
possible in practice, so a limit of 1000 entries will likely be
closer to 0.5 MB.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
if we succeed grabbing the refcount, then
if (err && !xfrm_pol_hold_rcu)
will evaluate to false so this hits last else branch which then
sets policy to ERR_PTR(0).
Fixes: ae33786f73 ("xfrm: policy: only use rcu in xfrm_sk_policy_lookup")
Reported-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Tested-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Userland client should be able to read an event, and reflect it back to
the kernel, therefore it needs to extract complete set of netlink flags.
For example, this will allow "tc monitor" to distinguish Add and Replace
operations.
Signed-off-by: Roman Mashak <mrv@mojatatu.com>
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
