As we have the pinctrl and clock support for the V3s SoC, it's now to
run a mainline Linux on it.
So add a .dtsi file for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
[Maxime: Removed the dependency on the CCU headers]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
While the SinA31s does have a proper 5-pin mini USB OTG port, the ID
pin does not seem to work. The pin used in the schematics is always low,
regardless of the attached OTG cable or SoC internal pin bias settings.
The v1.5 board is missing bias resistors shown in the schematics for
earlier revisions, and the connections of the remaining one does not
match the schematics either.
In addition, VBUS for this port is disconnected from the board's 5V
power rail. The board features a pad to solder jumper pins to connect
VBUS to 5V manually.
Given the above and the fact that the board has 5 more USB host ports,
it makes more sense to have the OTG port work in peripheral mode.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Previously, the sun8i tablets used everything declared in AXP221 DTSI
while they have an AXP223 PMIC.
This corrects that so the sun8i tablets can get some features the AXP223
has (at the moment, ability to have 100mA as maximal current on VBUS
power supply).
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Previously, the Allwinner Parrot R16 used everything declared in AXP221
DTSI while it has an AXP223 PMIC.
This corrects that so the Allwinner Parrot R16 can get some features the
AXP223 has (at the moment, ability to have 100mA as maximal current on
VBUS power supply).
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Previously, the Sinlinx SinA33 used everything declared in AXP221 DTSI
while it has an AXP223 PMIC.
This corrects that so the Sinlinx SinA33 can get some features the
AXP223 has (at the moment, ability to have 100mA as maximal current on
VBUS power supply).
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Previously, the Olimex A33-OlinuXino used everything declared in AXP221
DTSI while it has an AXP223 PMIC.
This corrects that so the Olimex A33-OlinuXino can get some features the
AXP223 has (at the moment, ability to have 100mA as maximal current on
VBUS power supply).
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The AXP223 shares most of its logic with the AXP221 but it has some
differences for the VBUS driver.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This adds the "x-powers,axp223-usb-power-supply" to the list of
compatibles for AXP20X VBUS power supply driver.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Banana Pro has an AMPAK AP6181 WiFi+Bluetooth module. The WiFi part
is a BCM43362 IC connected to MMC3 of the A20 SoC via SDIO. The IC also
takes a power enable signal via GPIO.
This commit adds a device-tree node to power it up, so the mmc subsys
can scan it, and enables the mmc controller which is connected to it.
As the wifi enable pin of the AP6181 module is not really a regulator,
switch the mmc3 node to the mmc-pwrseq framework for controlling it.
This more accurately reflectes how the hardware actually works.
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enable the S/PDIF transmitter that is present on the Mele I7.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Shenzhen Xunlong Software CO.,Limited is a SBC vendor, which produces
the "Orange Pi" series of SBCs.
Add a vendor prefix for it. This prefix is already used in many
Allwinner H3 boards.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Orange Pi PC routes the LINEOUT pins to the audio out jack on the
board. The onboard microphone is routed to MIC1, with MBIAS providing
power.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Now that we support the audio codec found on the Allwinner H3 SoC, add
device nodes for it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A23 Q8 tablets have an internal mono speaker w/ external amp
which has a shutdown control tied to a GPIO pin. Both the speaker
amp and the headphone jack are tied to the HP output pins. While
the speaker is mono, the headset jack is stereo. Unfortunately
the driver does not support automatic switching of this.
In addition, the headset is DC coupled, or "direct drive" enabled.
The headset's microphone is tied to MIC2 with HBIAS providing power.
A separate internal microphone is tied to MIC1 with MBIAS providing
power.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Now that we have a device tree binding and driver for the A23's
internal audio codec, add a device node for it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
On the A23/A33, the internal codec's analog path controls are located in
the PRCM node.
Add a sub-device node to the PRCM for it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
UEXT are Universal EXTension connector from Olimex. They embed i2c, spi
and uart pins along power in one connector and are found on most,
if not all, Olimex boards.
The Olimex A20 SOM EVB have two UEXT connector so enable the nodes found on
those two connectors.
Signed-off-by: Emmanuel Vadot <manu@bidouilliste.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This commit enables the on-chip audio codec present on the A20 SoC
on the Banana Pro board.
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The spi0 controller on the A20 have up to 4 CS (Chip Select) while the
others three only have 1.
Add the num-cs property to each node.
The current driver doesn't read this property but this is useful for
downstream user of DTS (FreeBSD for example).
Signed-off-by: Emmanuel Vadot <manu@bidouilliste.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Use axp209.dtsi in sun7i-a20-olinuxino-lime2.dts and correct
some regulators.
DCDC2 is used for vdd-cpu so it should never be bellow 1V and above 1.4V
DCDC3 is used for VDD_INT so same as above.
LD01 is used for the RTC, and should have a typical value of 1.3V
LD02 is used for AVCC and should have a typical value of 3.0V
LD03/4 are used for Port-E/Port-G Power pin, and the schematics recommands
to set them to 2.8V as they can be used for CSI0/1.
Signed-off-by: Emmanuel Vadot <manu@bidouilliste.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Lichee Pi One is a low-cost Allwinner A13-based development board, with
an AXP209 PMU, a USB2.0 OTG port, a USB2.0 host port (or an onboard
RTL8723BU Wi-Fi card), optional headers for LCD and CSI, two GPIO
headers and two MicroSD card slots (connected to mmc0 and mmc2, both
bootable).
Add support for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Lichee Pi is a new "Pi"-named development board series.
Currently available device, Lichee Pi One, is by only one person as
night job, so the device series name is chosen to be the vendor prefix.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Some board only use 4bit mode of mmc2.
Add a pinctrl node for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This patch adds the regulator nodes for the axp209 by including
the axp209 dtsi.
DCDC2 is used as the cpu power supply. This patch also references
it from the cpu node.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add the SPDIF transceiver controller block to the A31 dtsi.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add the SPDIF TX pin to the A31 dtsi.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Mele I7 has an audio jack for the SoC's internal codec.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
XR819 seems to need a delay after its reset line to be deasserted,
otherwise it may not respond MMC commands correctly, and fail to
initialize.
Add a 200ms delay in the mmc-pwrseq.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
An operating point table is needed for the cpu frequency adjusting to
work.
The operating point table is converted from the common value in
extracted script.fex from many A33 board/tablets.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
All reference design A33 tablets uses DCDC2 of AXP223 as the power
supply of the Cortex-A7 cores.
Set the cpu-supply in the DTSI of sun8i reference tablets.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
A "cpu0" label is needed on cpu@0 for cpufreq-dt to work.
Add such a label, in order to prepare for cpufreq support of A23/33.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Orange Pi Zero is a board that came with the new Allwinner H2+ SoC and a
SDIO Wi-Fi chip by Allwinner (XR819).
Add a device tree file for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A31 Hummingbird has a mini USB OTG port, and uses GPIO pins from the
SoC for ID pin and VBUS detection and VBUS control. The PMIC can also do
VBUS detection and control.
Here we prefer to use the PMIC's DRIVEVBUS function to control VBUS for
USB OTG, as that is the hardware default.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In the past, all the MMC pins had
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
which was actually a no-op. We were relying on U-boot to set the bias
pull up for us. These properties were removed as part of the fix up to
actually support no bias on the pins. During the transition some boards
experienced regular MMC time-outs during normal operation, while others
completely failed to initialize the SD card.
Given that MMC starts in open-drain mode and the pull-ups are required,
it's best to enable it for all the pin settings.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Now that we can handle the generic pinctrl bindings, convert our DT to it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
The allwinner,pull property set to NO_PULL was really considered our
default (and wasn't even changing the default value in the code).
Remove these properties to make it obvious that we do not set anything in
such a case.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
The allwinner,drive property set to 10mA was really considered as our
default. Remove all those properties entirely to make that obvious.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
I am getting the following warning when I build kernel 4.9-git on my
PowerBook G4 with a 32-bit PPC processor:
AS arch/powerpc/kernel/misc_32.o
arch/powerpc/kernel/misc_32.S:299:7: warning: "CONFIG_FSL_BOOKE" is not defined [-Wundef]
This problem is evident after commit 989cea5c14 ("kbuild: prevent
lib-ksyms.o rebuilds"); however, this change in kbuild only exposes an
error that has been in the code since 2005 when this source file was
created. That was with commit 9994a33865 ("powerpc: Introduce
entry_{32,64}.S, misc_{32,64}.S, systbl.S").
The offending line does not make a lot of sense. This error does not
seem to cause any errors in the executable, thus I am not recommending
that it be applied to any stable versions.
Thanks to Nicholas Piggin for suggesting this solution.
Fixes: 9994a33865 ("powerpc: Introduce entry_{32,64}.S, misc_{32,64}.S, systbl.S")
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The timer type simplifications caused a new gcc warning:
drivers/base/power/domain.c: In function ‘genpd_runtime_suspend’:
drivers/base/power/domain.c:562:14: warning: ‘time_start’ may be used uninitialized in this function [-Wmaybe-uninitialized]
elapsed_ns = ktime_to_ns(ktime_sub(ktime_get(), time_start));
despite the actual use of "time_start" not having changed in any way.
It appears that simply changing the type of ktime_t from a union to a
plain scalar type made gcc check the use.
The variable wasn't actually used uninitialized, but gcc apparently
failed to notice that the conditional around the use was exactly the
same as the conditional around the initialization of that variable.
Add an unnecessary initialization just to shut up the compiler.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull timer type cleanups from Thomas Gleixner:
"This series does a tree wide cleanup of types related to
timers/timekeeping.
- Get rid of cycles_t and use a plain u64. The type is not really
helpful and caused more confusion than clarity
- Get rid of the ktime union. The union has become useless as we use
the scalar nanoseconds storage unconditionally now. The 32bit
timespec alike storage got removed due to the Y2038 limitations
some time ago.
That leaves the odd union access around for no reason. Clean it up.
Both changes have been done with coccinelle and a small amount of
manual mopping up"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
ktime: Get rid of ktime_equal()
ktime: Cleanup ktime_set() usage
ktime: Get rid of the union
clocksource: Use a plain u64 instead of cycle_t
Pull SMP hotplug notifier removal from Thomas Gleixner:
"This is the final cleanup of the hotplug notifier infrastructure. The
series has been reintgrated in the last two days because there came a
new driver using the old infrastructure via the SCSI tree.
Summary:
- convert the last leftover drivers utilizing notifiers
- fixup for a completely broken hotplug user
- prevent setup of already used states
- removal of the notifiers
- treewide cleanup of hotplug state names
- consolidation of state space
There is a sphinx based documentation pending, but that needs review
from the documentation folks"
* 'smp-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/armada-xp: Consolidate hotplug state space
irqchip/gic: Consolidate hotplug state space
coresight/etm3/4x: Consolidate hotplug state space
cpu/hotplug: Cleanup state names
cpu/hotplug: Remove obsolete cpu hotplug register/unregister functions
staging/lustre/libcfs: Convert to hotplug state machine
scsi/bnx2i: Convert to hotplug state machine
scsi/bnx2fc: Convert to hotplug state machine
cpu/hotplug: Prevent overwriting of callbacks
x86/msr: Remove bogus cleanup from the error path
bus: arm-ccn: Prevent hotplug callback leak
perf/x86/intel/cstate: Prevent hotplug callback leak
ARM/imx/mmcd: Fix broken cpu hotplug handling
scsi: qedi: Convert to hotplug state machine
Pull turbostat updates from Len Brown.
* 'turbostat' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
tools/power turbostat: remove obsolete -M, -m, -C, -c options
tools/power turbostat: Make extensible via the --add parameter
tools/power turbostat: Denverton uses a 25 MHz crystal, not 19.2 MHz
tools/power turbostat: line up headers when -M is used
tools/power turbostat: fix SKX PKG_CSTATE_LIMIT decoding
tools/power turbostat: Support Knights Mill (KNM)
tools/power turbostat: Display HWP OOB status
tools/power turbostat: fix Denverton BCLK
tools/power turbostat: use intel-family.h model strings
tools/power/turbostat: Add Denverton RAPL support
tools/power/turbostat: Add Denverton support
tools/power/turbostat: split core MSR support into status + limit
tools/power turbostat: fix error case overflow read of slm_freq_table[]
tools/power turbostat: Allocate correct amount of fd and irq entries
tools/power turbostat: switch to tab delimited output
tools/power turbostat: Gracefully handle ACPI S3
tools/power turbostat: tidy up output on Joule counter overflow
Add a new page flag, PageWaiters, to indicate the page waitqueue has
tasks waiting. This can be tested rather than testing waitqueue_active
which requires another cacheline load.
This bit is always set when the page has tasks on page_waitqueue(page),
and is set and cleared under the waitqueue lock. It may be set when
there are no tasks on the waitqueue, which will cause a harmless extra
wakeup check that will clears the bit.
The generic bit-waitqueue infrastructure is no longer used for pages.
Instead, waitqueues are used directly with a custom key type. The
generic code was not flexible enough to have PageWaiters manipulation
under the waitqueue lock (which simplifies concurrency).
This improves the performance of page lock intensive microbenchmarks by
2-3%.
Putting two bits in the same word opens the opportunity to remove the
memory barrier between clearing the lock bit and testing the waiters
bit, after some work on the arch primitives (e.g., ensuring memory
operand widths match and cover both bits).
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Bob Peterson <rpeterso@redhat.com>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Andrew Lutomirski <luto@kernel.org>
Cc: Andreas Gruenbacher <agruenba@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A page is not added to the swap cache without being swap backed,
so PageSwapBacked mappings can use PG_owner_priv_1 for PageSwapCache.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Acked-by: Hugh Dickins <hughd@google.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Bob Peterson <rpeterso@redhat.com>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Andrew Lutomirski <luto@kernel.org>
Cc: Andreas Gruenbacher <agruenba@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
No point in going through loops and hoops instead of just comparing the
values.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
ktime_set(S,N) was required for the timespec storage type and is still
useful for situations where a Seconds and Nanoseconds part of a time value
needs to be converted. For anything where the Seconds argument is 0, this
is pointless and can be replaced with a simple assignment.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
ktime is a union because the initial implementation stored the time in
scalar nanoseconds on 64 bit machine and in a endianess optimized timespec
variant for 32bit machines. The Y2038 cleanup removed the timespec variant
and switched everything to scalar nanoseconds. The union remained, but
become completely pointless.
Get rid of the union and just keep ktime_t as simple typedef of type s64.
The conversion was done with coccinelle and some manual mopping up.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
There is no point in having an extra type for extra confusion. u64 is
unambiguous.
Conversion was done with the following coccinelle script:
@rem@
@@
-typedef u64 cycle_t;
@fix@
typedef cycle_t;
@@
-cycle_t
+u64
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: John Stultz <john.stultz@linaro.org>
The mpic is either the main interrupt controller or is cascaded behind a
GIC. The mpic is single instance and the modes are mutually exclusive, so
there is no reason to have seperate cpu hotplug states.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Link: http://lkml.kernel.org/r/20161221192112.333161745@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
