- Support for CPU clks on Raspberry Pi devices
- Slow clk support for AT91 SAM9X60 SoCs
* clk-rpi-cpufreq:
clk: raspberrypi: register platform device for raspberrypi-cpufreq
firmware: raspberrypi: register clk device
clk: bcm283x: add driver interfacing with Raspberry Pi's firmware
clk: bcm2835: remove pllb
* clk-tegra:
clk: tegra: Do not enable PLL_RE_VCO on Tegra210
clk: tegra: Warn if an enabled PLL is in IDDQ
clk: tegra: Do not warn unnecessarily
clk: tegra210: fix PLLU and PLLU_OUT1
* clk-simplify-provider.h:
clk: consoldiate the __clk_get_hw() declarations
clk: Unexport __clk_of_table
clk: Remove ifdef for COMMON_CLK in clk-provider.h
* clk-sprd:
clk: sprd: Add check for return value of sprd_clk_regmap_init()
clk: sprd: Check error only for devm_regmap_init_mmio()
clk: sprd: Switch from of_iomap() to devm_ioremap_resource()
* clk-at91:
clk: at91: sckc: use dedicated functions to unregister clock
clk: at91: sckc: improve error path for sama5d4 sck registration
clk: at91: sckc: remove unnecessary line
clk: at91: sckc: improve error path for sam9x5 sck register
clk: at91: sckc: add support to free slow clock osclillator
clk: at91: sckc: add support to free slow rc oscillator
clk: at91: sckc: add support to free slow oscillator
clk: at91: sckc: add support for SAM9X60
dt-bindings: clk: at91: add bindings for SAM9X60's slow clock controller
clk: at91: sckc: add support to specify registers bit offsets
clk: at91: sckc: sama5d4 has no bypass support
Without this we were getting errors like:
In file included from drivers/clk/clkdev.c:22:0:
drivers/clk/clk.h:36:23: error: static declaration of '__clk_get_hw' follows non-static declaration
include/linux/clk-provider.h:808:16: note: previous declaration of '__clk_get_hw' was here
Fixes: 59fcdce425 ("clk: Remove ifdef for COMMON_CLK in clk-provider.h")
fixes: 73e0e496af ("clkdev: Always allocate a struct clk and call __clk_get() w/ CCF")
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Call imx_register_uart_clocks() API to keep uart clocks enabled
when earlyprintk or earlycon is active.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Some of i.MX SoCs' clock driver use platform driver model,
and they need to call imx_register_uart_clocks() API, so
imx_register_uart_clocks() API should NOT be in .init section.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation http www opensource org
licenses gpl license html http www gnu org copyleft gpl html
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 3 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081201.897982733@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The imx6q_obtain_fixed_clk_hw lacks an __init marker, which
leads to this otherwise harmless warning:
WARNING: vmlinux.o(.text+0x495358): Section mismatch in reference from the function imx6q_obtain_fixed_clk_hw() to the function .init.text:imx_obtain_fixed_clock_hw()
The function imx6q_obtain_fixed_clk_hw() references
the function __init imx_obtain_fixed_clock_hw().
This is often because imx6q_obtain_fixed_clk_hw lacks a __init
annotation or the annotation of imx_obtain_fixed_clock_hw is wrong.
Fixes: 992b703b5b ("clk: imx6q: Switch to clk_hw based API")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Some of i.MX SoCs' clock driver use platform driver model,
and they need to call imx_check_clocks() API, so
imx_check_clocks() API should NOT be in .init section.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Switch the entire clk-imx6sll driver to clk_hw based API.
This allows us to move closer to a clear split between
consumer and provider clk APIs.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Switch the entire clk-imx7d driver to clk_hw based API. This allows us
to move closer to a clear split between consumer and provider clk APIs.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Switch the entire clk-imx6ul driver to clk_hw based API. This allows us
to move closer to a clear split between consumer and provider clk APIs.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Switch the entire clk-imx6sx driver to clk_hw based API. This allows us
to move closer to a clear split between consumer and provider clk APIs.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Switch the entire clk-imx6q driver to clk_hw based API.
Add imx6q_obtain_fixed_clk_hw helper to clean up the registration
of the clocks that are either found in device tree or are assigned
a fixed zero rate. This switch allows us to move closer to a clear
split between consumer and provider clk APIs.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Switch the entire clk-imx6sl driver to clk_hw based API.
This allows us to move closer to a clear split between
consumer and provider clk APIs.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Switch all the wrappers to clk_hw based API and rename them to indicate
that. Add macros for clk based legacy users. This allows us to move
closer to a clear split between consumer and provider clk APIs.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Switch the imx_clk_fixup_mux function to clk_hw based API, rename
accordingly and add a macro for clk based legacy. a macro for clk
based legacy. This allows us to move closer to a clear split between
consumer and provider clk APIs.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Switch the imx_clk_fixup_divider function to clk_hw based API, rename
accordingly and add a macro for clk based legacy. This allows us to
move closer to a clear split between consumer and provider clk APIs.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Switch the imx_clk_gate_exclusive function to clk_hw based API, rename
accordingly and add a macro for clk based legacy. This allows us to move
closer to a clear split between consumer and provider clk APIs.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Switch the imx_clk_pfd function to clk_hw based API, rename accordingly
and add a macro for clk based legacy. This allows us to move closer to
a clear split between consumer and provider clk APIs.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Switch the imx_clk_hw_pllv3 function to clk_hw based API, rename
accordingly and add a macro for clk based legacy. This allows us
to move closer to a clear split between consumer and provider clk
APIs.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Switch the clk_register_gate2 function to clk_hw based API, rename
accordingly and add a macro for clk based legacy. This allows us to
move closer to a clear split between consumer and provider clk APIs.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Switch the clk_cpu clock registering function to clk_hw based API and add
a macro for clk based legacy. This allows us to move closer to a clear
split between consumer and provider clk APIs.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Switch all the clk_busy clock registering functions to clk_hw based API.
Keep around some clk based wrappers to be used by older imx platforms.
This allows us to move closer to a clear split of consumer and provider
clk APIs.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The clock is registered later than these two re-parentings.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The clock IMX6SX_CLK_AXI is not registered at all.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
In order to move to clk_hw based API, imx_obtain_fixed_clock_hw
is added. The end goal here is to have all the clk providers use
the clk_hw based API.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There is no audio_pll2_clk registered, it should be audio_pll2_out.
Cc: <stable@vger.kernel.org>
Fixes: ba5625c3e2 ("clk: imx: Add clock driver support for imx8mm")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not write to the free
software foundation inc 51 franklin st fifth floor boston ma 02110
1301 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 246 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190530000436.674189849@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is another set of reviewed patches that adds SPDX tags to different
kernel files, based on a set of rules that are being used to parse the
comments to try to determine that the license of the file is
"GPL-2.0-or-later" or "GPL-2.0-only". Only the "obvious" versions of
these matches are included here, a number of "non-obvious" variants of
text have been found but those have been postponed for later review and
analysis.
There is also a patch in here to add the proper SPDX header to a bunch
of Kbuild files that we have missed in the past due to new files being
added and forgetting that Kbuild uses two different file names for
Makefiles. This issue was reported by the Kbuild maintainer.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on the
patches are reviewers.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXPCHLg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykxyACgql6ktH+Tv8Ho1747kKPiFca1Jq0AoK5HORXI
yB0DSTXYNjMtH41ypnsZ
=x2f8
-----END PGP SIGNATURE-----
Merge tag 'spdx-5.2-rc3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull yet more SPDX updates from Greg KH:
"Here is another set of reviewed patches that adds SPDX tags to
different kernel files, based on a set of rules that are being used to
parse the comments to try to determine that the license of the file is
"GPL-2.0-or-later" or "GPL-2.0-only". Only the "obvious" versions of
these matches are included here, a number of "non-obvious" variants of
text have been found but those have been postponed for later review
and analysis.
There is also a patch in here to add the proper SPDX header to a bunch
of Kbuild files that we have missed in the past due to new files being
added and forgetting that Kbuild uses two different file names for
Makefiles. This issue was reported by the Kbuild maintainer.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on
the patches are reviewers"
* tag 'spdx-5.2-rc3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (82 commits)
treewide: Add SPDX license identifier - Kbuild
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 225
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 224
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 223
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 222
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 221
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 220
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 218
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 217
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 216
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 215
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 214
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 213
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 211
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 210
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 209
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 207
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 206
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 203
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 201
...
- Don't expose the SiFive clk driver on non-RISCV architectures
- Fix some bits describing clks in the imx8mm driver
- Always call clk domain code in the TI driver so non-legacy platforms
work
-----BEGIN PGP SIGNATURE-----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=gbSJ
-----END PGP SIGNATURE-----
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk driver fixes from Stephen Boyd:
- Don't expose the SiFive clk driver on non-RISCV architectures
- Fix some bits describing clks in the imx8mm driver
- Always call clk domain code in the TI driver so non-legacy platforms
work
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: ti: clkctrl: Fix clkdm_clk handling
clk: imx: imx8mm: fix int pll clk gate
clk: sifive: restrict Kconfig scope for the FU540 PRCI driver
Based on 1 normalized pattern(s):
the code contained herein is licensed under the gnu general public
license you may obtain a copy of the gnu general public license
version 2 or later at the following locations http www opensource
org licenses gpl license html http www gnu org copyleft gpl html
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 161 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.383790741@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MMDC_P1_IPG clock need to be on always on to make sure
the MMDC register can be accessed successfully.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This clock is used for dram operations inside TF-A and must be kept
enabled for features such as suspend/resume dram retention and busfreq
to work.
This is required for imx8mm suspend to work with NXP branch of TF-A.
There is an equivalent clk on imx8mq and it's always been marked as
critical in upstream.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Since i.MX7ULP B0 chip, nic1_bus_clk's parent is changed to
from nic0_clk directly, update it accordingly.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use imx_mmdc_mask_handshake() API instead of programming CCM
register directly in each platform to mask unused MMDC channel's
handshake.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
All i.MX6 SoCs need to mask unused MMDC channel's handshake
for low power modes, this patch provides common API for masking
the MMDC channel passed from caller.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This is documented in the reference manuals as GIC_CLK_ROOT.
In some out-of-tree DVFS scenarios the gic clock can end up as the only
user of sys_pll2 so if we don't define the gic clk explicitly it might
be turned off.
This applies to both 8mq and 8mm: same clk register but diffferent
parents.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX8MM has clock gate for SNVS module, add it into clock tree
for SNVS RTC driver to manage.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX8MQ has clock gate for SNVS module, add it into clock tree
for SNVS RTC driver to manage.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
To Frac pll, the gate shift is 13, however to Int PLL the gate shift
is 11.
Cc: <stable@vger.kernel.org>
Fixes: ba5625c3e2 ("clk: imx: Add clock driver support for imx8mm")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 2 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154042.615184352@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation inc
51 franklin street fifth floor boston ma 02110 1301 usa
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option [no]_[pad]_[ctrl] any later version this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not write to the free
software foundation inc 51 franklin street fifth floor boston ma
02110 1301 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 176 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154040.652910950@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
i.MX8MM has clock gate for each GPIO bank, add them
into clock tree for GPIO driver to manage.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
- Remove clk_readl() and introduce BE versions of basic clk types
* clk-doc:
clk: Drop duplicate clk_register() documentation
clk: Document and simplify clk_core_get_rate_nolock()
clk: Remove 'flags' member of struct clk_fixed_rate
clk: nxp: Drop 'flags' on fixed_rate clk macro
clk: Document __clk_mux_determine_rate()
clk: Document CLK_MUX_READ_ONLY mux flag
clk: Document deprecated things
clk: Collapse gpio clk kerneldoc
* clk-more-critical:
clk: highbank: Convert to CLK_IS_CRITICAL
* clk-meson: (21 commits)
clk: meson: axg-audio: add g12a support
clk: meson: axg-audio: don't register inputs in the onecell data
clk: meson: axg_audio: replace prefix axg by aud
dt-bindings: clk: axg-audio: add g12a support
clk: meson: meson8b: add the video decoder clock trees
clk: meson: meson8b: add the VPU clock trees
clk: meson: meson8b: add support for the GP_PLL clock on Meson8m2
clk: meson: meson8b: use a separate clock table for Meson8m2
dt-bindings: clock: meson8b: export the video decoder clocks
clk: meson-g12a: add video decoder clocks
dt-bindings: clock: meson8b: export the VPU clock
clk: meson-g12a: add PCIE PLL clocks
dt-bindings: clock: g12a-aoclk: expose CLKID_AO_CTS_OSCIN
clk: meson-pll: add reduced specific clk_ops for G12A PCIe PLL
dt-bindings: clock: meson8b: drop the "ABP" clock definition
clk: meson: g12a: add cpu clocks
dt-bindings: clk: g12a-clkc: add VDEC clock IDs
dt-bindings: clock: axg-audio: unexpose controller inputs
dt-bindings: clk: g12a-clkc: add PCIE PLL clock ID
clk: g12a-aoclk: re-export CLKID_AO_SAR_ADC_SEL clock id
...
* clk-basic-be:
clk: core: replace clk_{readl,writel} with {readl,writel}
clk: core: remove powerpc special handling
powerpc/512x: mark clocks as big endian
clk: mux: add explicit big endian support
clk: multiplier: add explicit big endian support
clk: gate: add explicit big endian support
clk: fractional-divider: add explicit big endian support
clk: divider: add explicit big endian support
The operations of pfdv2 gate_bit/valid_bit are incorrect,
they are defined as u8 for bit offset, but gate_bit is
actually assigned as mask which could be 32 bit long and
it causes overflow, and vld_bit is assigned as bit offset
based on incorrect gate_bit value, it causes incorrect
pfd clock gate status in clock tree, this patch fixes the
issue by assigning them as correct bit offset.
Fixes: 9fcb6be3b6 ("clk: imx: add pfdv2 support")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warnings:
drivers/clk/imx/clk-pllv3.c: In function ‘imx_clk_pllv3’:
drivers/clk/imx/clk-pllv3.c:446:18: warning: this statement may fall through [-Wimplicit-fallthrough=]
pll->div_shift = 1;
~~~~~~~~~~~~~~~^~~
drivers/clk/imx/clk-pllv3.c:447:2: note: here
case IMX_PLLV3_USB:
^~~~
drivers/clk/imx/clk-pllv3.c:453:21: warning: this statement may fall through [-Wimplicit-fallthrough=]
pll->denom_offset = PLL_IMX7_DENOM_OFFSET;
^
drivers/clk/imx/clk-pllv3.c:454:2: note: here
case IMX_PLLV3_AV:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Fixes: b4a4cb5a04 ("clk: imx: correct i.MX7D AV PLL num/denom offset")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
It's defined in imx8mq-clock.h but wasn't assigned yet. It's used as
clk_tx_esc in the nwl dsi host controller (i.MX8MQ RM, Rev. 0, 01/2018
Sect. 13.5.3.7.4).
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Keep uart clocks enabled when earlyprintk or
earlycon is active.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
According reference manual, i.MX7D's audio/video PLL's
num/denom register offset are 0x20/0x30, they are different
from i.MX6's audio/video PLL, correct it by introducing new
offset variables for audio/video PLL and using runtime
assignment based on PLL type.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This looks like a copy-paste error. This string is not referenced
anywhere so it's safe to rename it.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
It does not make sense to only get value from pll->base and assign
to a local variable when recalc_rate.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
- Remove SNVS clock from i.MX7UPL clock driver and bindings, as the
clock will be visible on M4 core only, and never be accessed by
Cortex-A cores.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcvThaAAoJEFBXWFqHsHzOoR0H/0AjB+fmbMoeGEpo0pZjPFyw
RbQ/+UavX0Yy4z4LJmYw3y3n7/cLvyv8Edg/BRXCvgX6dmjHa6sOSW3rZSD7BWUp
Jg6m/NCkaq4GRFOfXrs+vzmjtEECyq5j6EV9QG8w3ZBEU733FkcQgMTsOmK9u7kF
fxUfz7PReS6ZPk276gTMwWaNOl1R6W8eaHjiK0F1LQIcZfPRcsPtFRFkriQ27m/7
MOJ5Wjpf5804qis3p8gDIc/Z+wPaf5QF0exNKL/55INjVeSwCw81TAqTpFWrkrgj
lF2DTXgBHVO9S03I5/d5CNFCYdlP7EbgRD5CoH7mWrqEiBnvUUAxhe5zlm4etno=
=4yV1
-----END PGP SIGNATURE-----
Merge tag 'clk-imx7ulp-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into clk-imx
Pull i.MX7UPL clk changes from Shawn Guo:
- Remove SNVS clock from i.MX7UPL clock driver and bindings, as the
clock will be visible on M4 core only, and never be accessed by
Cortex-A cores
* tag 'clk-imx7ulp-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
dt-bindings: clock: imx7ulp: remove SNVS clock
clk: imx7ulp: remove snvs clock
- A couple of patches from Jonathan Neuschäfer to improve i.MX5 clock
driver for i.MX50 support.
- Rename file clk-imx51-imx53.c to clk-imx5.c, as it covers support for
all i.MX5 series SoCs including i.MX50.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcvTXlAAoJEFBXWFqHsHzO9oAH+wQtUGOJw7Yiu/UcjGQmoWRJ
0MRLknDBlVBTKSqZLVoFsm2xRyCkdHA7QB3OaCui4I40pdwoCOxDFHUOc2PTwBk2
kr0tHiiYoYXF6oZioD5tCh2zLHNuCIYy+TLzwG4jVavUCQAnQE8jzE59kiEvxBVg
9dvVxRjiIcHg0azm/oRsD+HQYwZ0ALMkLcAtbP1GGgsHeoSbaPJsYQCmj+9jDP8t
OKwgtum7DeYFlelCMF70BubA3NmAFz3uKrgh1lXRGSM5nm2aMmuNyypFIN6c7E53
ELWfXvRLfncl5uipeIc5Km5r0L+AwBQmH9aOyzd3i4Ys2z3Kp5atSEhuqbDWnDI=
=udGf
-----END PGP SIGNATURE-----
Merge tag 'clk-imx5-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into clk-imx
Pull i.MX5 clk changes from Shawn Guo:
- A couple of patches from Jonathan Neuschäfer to improve i.MX5 clock
driver for i.MX50 support
- Rename file clk-imx51-imx53.c to clk-imx5.c, as it covers support for
all i.MX5 series SoCs including i.MX50
* tag 'clk-imx5-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
clk: imx: rename clk-imx51-imx53.c to clk-imx5.c
clk: imx5: Fix i.MX50 ESDHC clock registers
clk: imx5: Fix i.MX50 mainbus clock registers
Now that clk_{readl,writel} is just an alias for {readl,writel}, we can
switch all users of clk_* to use the accessors directly and remove the
helpers.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
[sboyd@kernel.org: Also convert renesas file so that this can be
compile independently]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
As the driver is handling all i.MX5 series SoCs inlcuding i.MX50, rather
than just i.MX51 and i.MX53, let's rename it to clk-imx5.c.
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Code which initializes the "clk_init_data.ops" checks pll->rate_table
before that field is ever assigned to so it always picks
"clk_pll1416x_min_ops".
This breaks dynamic rate rounding for features such as cpufreq.
Fix by checking pll_clk->rate_table instead, here pll_clk refers to
the constant initialization data coming from per-soc clk driver.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Fixes: 8646d4dcc7 ("clk: imx: Add PLLs driver for imx8mm soc")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The MUX bits for esdhc_{a,c,d}_sel are shifted by one bit within CSCMR1,
because esdhc_b_sel (ESDHC3_CLK_SEL in the Reference Manual) is extended
by one bit.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX50 does not have a periph_apm clock. Instead, the main bus clock
(a.k.a. periph_clk) comes directly from a MUX between pll1_sw, pll2_sw,
pll3_sw, and lp_apm.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This is never used and the imx_clk_hw_fixed does the same thing.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Since i.MX7ULP B0 chip, the SNVS module is moved into M4
domain and its clock is also moved into PCC0 which is
contorlled by M4, Linux kernel should NOT add it into
clock tree.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
- Split LCDC into two clks on the Marvell MMP2 SoC
* clk-imx:
clk: imx8mq: add GPIO clocks to clock tree
clk: imx: Refactor entire sccg pll clk
clk: imx: scu: add cpu frequency scaling support
clk: imx: imx8mm: Mark init function __init
clk: imx8mq: Add the missing ARM clock
dt-bindings: imx8mq-clock: Add the missing ARM clock
clk: imx: imx8mq: Fix the rate propagation for arm pll
clk: imx8mq: Add support for the CLKO1 clock
clk: imx8mq: Fix the CLKO2 source select list
clk: imx8mq: Add missing M4 clocks
clk: imx: Add clock driver support for imx8mm
dt-bindings: imx: Add clock binding doc for imx8mm
clk: imx: Add PLLs driver for imx8mm soc
clk: imx5: add imx5_SCC2_IPG_GATE
clk: imx: scu: add set parent support
clk: imx: scu: add fallback compatible string support
clk: imx8mq: Make parent names arrays const pointers
clk: imx: Make parents const pointer in mux wrappers
clk: imx: Make parent_names const pointer in composite-8m
* clk-samsung:
clk: samsung: s3c2443: Mark expected switch fall-through
clk: samsung: exynos5: Fix kfree() of const memory on setting driver_override
clk: samsung: exynos5: Fix possible NULL pointer exception on platform_device_alloc() failure
clk: samsung: exynos5433: Add selected IMEM clocks
clk: samsung: dt-bindings: Document Exynos5433 IMEM CMU
clk: samsung: exynos5433: Fix name typo in sssx
clk: samsung: exynos5433: Fix definition of CLK_ACLK_IMEM_{200, 266} clocks
clk: samsung: dt-bindings: Add Exynos5433 IMEM CMU clock IDs
* clk-ti:
clk: clk-twl6040: Fix imprecise external abort for pdmclk
ARM: OMAP2+: hwmod: disable ick autoidling when a hwmod requires that
clk: ti: check clock type before doing autoidle ops
clk: ti: add a usecount for autoidle
clk: ti: generalize the init sequence of clk_hw_omap clocks
clk: ti: remove usage of CLK_IS_BASIC
clk: ti: add new API for checking if a provided clock is an OMAP clock
clk: ti: move clk_hw_omap list handling under generic part of the driver
* clk-uniphier-gear:
clk: uniphier: Fix update register for CPU-gear
* clk-mmp2-lcdc:
clk: mmp2: separate LCDC peripheral clk form the display clock
dt-bindings: marvell,mmp2: Add clock id for the LCDC clock
i.MX8MQ has clock gate for each GPIO bank, add them
into clock tree for GPIO driver to manage.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Make the entire combination of plls to be one single clock. The parents used
for bypasses are specified each as an index in the parents list.
The determine_rate does a lookup throughout all the possible combinations
for all the divs and returns the best possible 'setup' which in turn is used
by set_rate later to set up all the divs and bypasses.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Tested-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
On NXP's i.MX SoCs with system controller inside, CPU frequency
scaling can ONLY be done by system controller firmware, and it
can ONLY be requested from secure mode, so Linux kernel has to
call ARM SMC to trap to ARM-Trusted-Firmware to request system
controller firmware to do CPU frequency scaling.
This patch adds i.MX system controller CPU frequency scaling support,
it reuses cpufreq-dt driver and implement the CPU frequency scaling
inside SCU clock driver.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
It calls another __init marked function and thus causes a section
mismatch if we don't mark it this way.
Fixes: ba5625c3e2 ("clk: imx: Add clock driver support for imx8mm")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add the ARM clock as imx_clk_cpu type.
Will be used by cpufreq.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The arm pll bypass needs to propagate the rate upwards
in order for the cpufreq to work.
Fixes: b80522040c ("clk: imx: Add clock driver for i.MX8MQ CCM")
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add the entry for the CLKO1 clock.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The CLKO2 clock source select list is the following as per the i.MX8M
Reference Manual:
000 - 25M_REF_CLK
001 - SYSTEM_PLL2_DIV5
010 - SYSTEM_PLL1_DIV2
011 - SYSTEM_PLL2_DIV6
100 - SYSTEM_PLL3_CLK
101 - AUDIO_PLL1_CLK
110 - VIDEO_PLL1_CLK
111 - 32K_REF_CLK
However, in imx8mq_clko2_sels[] only the first four entries are correct.
Fix it by adding the missing "sys3_pll2_out" entry in order to match
the description from the manual.
Fixes: b80522040c ("clk: imx: Add clock driver for i.MX8MQ CCM")
Reported-by: Rogerio Pimentel <rogerio.silva@nxp.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The clocks list is missing the clocks for the M4 core.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
New PLLs are introduced on i.MX8M Mini SOC.
PLL1416X is Integer PLL, PLL1443X is a Frac PLL.
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This adds the missing clock for the SCC2 peripheral unit.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
SCU clock can be used in a similar way by IMX8QXP and IMX8QM SoCs.
Make the driver support "fsl,scu-clk" fallback compatible string
to allow other SoCs to reuse the common part.
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The arrays containing the mux selectors need to be of const pointer
to const char.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The parents needs to be pointer to const pointer to const char.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The parent_names needs to be pointer to const pointer to const char.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = kzalloc(sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL);
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
platform_get_resource() may fail and return NULL, so we should
better check it's return value to avoid a NULL pointer dereference
a bit later in the code.
This is detected by Coccinelle semantic patch.
@@
expression pdev, res, n, t, e, e1, e2;
@@
res = platform_get_resource(pdev, t, n);
+ if (!res)
+ return -EINVAL;
... when != res == NULL
e = devm_ioremap(e1, res->start, e2);
Fixes: 1e3121bfe5 ("clk: imx: add imx8qxp lpcg driver")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The of_find_compatible_node() returns a node pointer with refcount
incremented, but there is the lack of use of the of_node_put() when
done. Add the missing of_node_put() to release the refcount.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Fixes: 1f2c5fd5f0 ("ARM: imx: add VF610 clock support")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The of_find_compatible_node() returns a node pointer with refcount
incremented, but there is the lack of use of the of_node_put() when
done. Add the missing of_node_put() to release the refcount.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Fixes: 8f6d8094b2 ("ARM: imx: add imx7d clk tree support")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The of_find_compatible_node() returns a node pointer with refcount
incremented, but there is the lack of use of the of_node_put() when
done. Add the missing of_node_put() to release the refcount.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Fixes: d551356890 ("ARM: imx: add clock driver for imx6sx")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The of_find_compatible_node() returns a node pointer with refcount
incremented, but there is the lack of use of the of_node_put() when
done. Add the missing of_node_put() to release the refcount.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Fixes: 2acd1b6f88 ("ARM: i.MX6: implement clocks using common clock framework")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
SCU clock can be used in a similar way by IMX8QXP and IMX8QM SoCs.
Let's make the name of clock ID generic to allow other SoCs to reuse
the common part.
This patch only changes the clock id name and file name, so no
functional change.
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
i.MX7ULP has a Cortex-A7 CPU which can run in RUN mode
or HSRUN mode, it is controlled in SMC1 module. The RUN
mode and HSRUN mode will use different clock source for
ARM, "divcore" for RUN mode and "hsrun_divcore" for HSRUN
mode, so the control bits in SMC1 module can be abstracted
as a HW clock mux, this patch adds HSRUN mode related
clocks in SCG1 module and adds "arm" clock in SMC1 module
to support RUN mode and HSRUN mode switch.
Latest clock tree in RUN mode as below:
firc 0 0 0 48000000 0 0 50000
firc_bus_clk 0 0 0 48000000 0 0 50000
hsrun_scs_sel 0 0 0 48000000 0 0 50000
hsrun_divcore 0 0 0 48000000 0 0 50000
sosc 3 3 3 24000000 0 0 50000
spll_pre_sel 1 1 1 24000000 0 0 50000
spll_pre_div 1 1 2 24000000 0 0 50000
spll 1 1 2 528000000 0 0 50000
spll_pfd0 1 1 1 500210526 0 0 50000
spll_pfd_sel 1 1 0 500210526 0 0 50000
spll_sel 1 1 0 500210526 0 0 50000
scs_sel 1 1 0 500210526 0 0 50000
divcore 1 1 0 500210526 0 0 50000
arm 1 1 0 500210526 0 0 50000
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The Low-Power Clock Gate (LPCG) modules contain a local programming
model to control the clock gates for the peripherals. An LPCG module
is used to locally gate the clocks for the associated peripheral.
And they're bedind the SCU clock.
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add imx8qxp clk driver which is based on SCU firmware clock service.
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
[sboyd@kernel.org: Move the makefile rule higher in the file]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Remove the dependency between the i.MX8MQ CCM clock driver
and the CONFIG_SOC_IMX8MQ and use CONFIG_CLK_IMX8MQ instead.
CONFIG_CLK_IMX8MQ depends on ARCH_MXC && ARM64.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add SCU clock common part which will be used by client clock drivers.
SCU clocks are totally different from the legacy clocks (No much
legacy things can be reused), it's using a firmware interface now based
on SCU protocol. So a new configuration option CONFIG_MXC_CLK_SCU is added.
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
[sboyd@kernel.org: Mark ccm_ipc_handle static]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The patch introduces CONFIG_MXC_CLK option for legacy MMIO clocks,
this is required to compile legacy MMIO clock conditionally when adding
SCU based clocks for MX8 platforms later.
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The ENET PLL is different from the other i.MX6 PLLs, as it has
multiple outputs with different post-dividers, which are all
bypassed if the single bypass bit is activated. The hardware setup
looks something like this:
_
refclk-o---PLL---o----DIV1-----| \
| | |M |----OUT1
o-----------------------|_/
| | _
| o----DIV2-----| \
| | |M |----OUT2
o-----------------------|_/
| | _
| `----DIV3-----| \
| |M |----OUT3
`-----------------------|_/
The bypass bit not only bypasses the PLL, but also the attached
post-dividers. This would be reasonbly straight forward to model
with a single output, or with different bypass bits for each output,
but sadly the HW guys decided that it would be good to actuate all
3 muxes with a single bit.
So the need to have the PLL bypassed for one of the outputs always
affects 2 other (in our model) independent branches of the clock
tree.
This means the decision to bypass this PLL is a system wide design
choice and should not be changed on-the-fly, so we can treat any
bapass configuration as static. As such we can just register the
post-dividiers with a ratio that reflects the bypass status, which
allows us to bypass the PLL without breaking our abstraction model
and with it DT stability.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
When specifying external clock inputs to the CCM the current code
requires the clocks to be in a "clocks" child node of the DT root.
This is not really conformant with DT best practices.
To avoid the need to deviate from those best practices, allow the
clock inputs to be specified via standard clock handles. This is
in line with how drivers of the later CCM driver revisions on
newer i.MX SoCs handle this.
As we can't retroactively change the DT binding, allow this as an
option with a fallback to the old way of how this has been handled.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The exclusive gates may be set up in the wrong way by software running
before the clock driver comes up. In that case the exclusive setup is
locked in its initial state, as the complementary function can't be
activated without disabling the initial setup first.
To avoid this lock situation, reset the exclusive gates to the off
state and allow the kernel to provide the proper setup.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Dong Aisheng <Aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
On i.MX6QP/i.MX6Q/i.MX6DL, there are DCIC1/DCIC2 clocks
gate in CCM_CCGR0 register, add them into clock tree for
clock management.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Same as other i.MX6 SoCs, ensure unused MMDC channel's
handshake is bypassed, this is to make sure no request
signal will be generated when periphe_clk_sel is changed
or SRC warm reset is triggered.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The initialization of ret is redundant as it is being re-assigned to
the return value from the call to imx8m_clk_composite_compute_dividers.
Clean this up by removing the initialization.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
i.MX7ULP Clock functions are under joint control of the System
Clock Generation (SCG) modules, Peripheral Clock Control (PCC)
modules, and Core Mode Controller (CMC)1 blocks
The clocking scheme provides clear separation between M4 domain
and A7 domain. Except for a few clock sources shared between two
domains, such as the System Oscillator clock, the Slow IRC (SIRC),
and and the Fast IRC clock (FIRCLK), clock sources and clock
management are separated and contained within each domain.
M4 clock management consists of SCG0, PCC0, PCC1, and CMC0 modules.
A7 clock management consists of SCG1, PCC2, PCC3, and CMC1 modules.
This driver only adds clock support in A7 domain.
Note that most clocks required to be operated when gated, e.g. pll,
pfd, pcc. And more special cases that scs/ddr/nic mux selecting
different clock source requires that clock to be enabled first,
then we need set CLK_OPS_PARENT_ENABLE flag for them properly.
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Anson Huang <Anson.Huang@nxp.com>
Cc: Bai Ping <ping.bai@nxp.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Clock providers are recommended to use the new struct clk_hw based API,
so implement IMX clk_hw based provider helpers functions to the new
approach.
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
As the commit 2893c37946 ("clk: make strings in parent name arrays
const"), let's make the parent strings const, otherwise we may meet
the following warning when compiling:
drivers/clk/imx/clk-imx7ulp.c: In function 'imx7ulp_clocks_init':
drivers/clk/imx/clk-imx7ulp.c:73:35: warning: passing argument 5 of
'imx_clk_mux_flags' discards 'const' qualifier from pointer target type
clks[IMX7ULP_CLK_APLL_PRE_SEL] = imx_clk_mux_flags("apll_pre_sel", base + 0x508, 0,
1, pll_pre_sels, ARRAY_SIZE(pll_pre_sels), CLK_SET_PARENT_GATE);
^
In file included from drivers/clk/imx/clk-imx7ulp.c:23:0:
drivers/clk/imx/clk.h:200:27: note: expected 'const char **' but argument is
of type 'const char * const*'
...
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The imx composite clk is designed for Peripheral Clock Control (PCC)
module observed in IMX ULP SoC series.
NOTE pcc can only be operated when clk is gated.
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Anson Huang <Anson.Huang@nxp.com>
Cc: Bai Ping <ping.bai@nxp.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
[sboyd@kernel.org: Include clk.h for sparse warnings]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The pfdv2 is designed for PLL Fractional Divide (PFD) observed in System
Clock Generation (SCG) module in IMX ULP SoC series. e.g. i.MX7ULP.
NOTE pfdv2 can only be operated when clk is gated.
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Anson Huang <Anson.Huang@nxp.com>
Cc: Bai Ping <ping.bai@nxp.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
[sboyd@kernel.org: Include clk.h for sparse warnings]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
pllv4 is designed for System Clock Generation (SCG) module observed
in IMX ULP SoC series. e.g. i.MX7ULP.
The SCG modules generates clock used to derive processor, system,
peripheral bus and external memory interface clocks while this patch
intends to support the PLL part.
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Anson Huang <Anson.Huang@nxp.com>
Cc: Bai Ping <ping.bai@nxp.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
[sboyd@kernel.org: Include clk.h for sparse warnings]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
For dividers with zero indicating clock is disabled, instead of giving a
warning each time like "clkx: Zero divisor and CLK_DIVIDER_ALLOW_ZERO not
set" in exist code, we'd like to introduce enable/disable function for it.
e.g.
000b - Clock disabled
001b - Divide by 1
010b - Divide by 2
...
Set rate when the clk is disabled will cache the rate request and only
when the clk is enabled will the driver actually program the hardware to
have the requested divider value. Similarly, when the clk is disabled we'll
write a 0 there, but when the clk is enabled we'll restore whatever rate
(divider) was chosen last.
It does mean that recalc rate will be sort of odd, because when the clk is
off it will return 0, and when the clk is on it will return the right rate.
So to make things work, we'll need to return the cached rate in recalc rate
when the clk is off and read the hardware when the clk is on.
NOTE for the default off divider, the recalc rate will still return 0 as
there's still no proper preset rate. Enable such divider will give user
a reminder error message.
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
[sboyd@kernel.org: Include clk.h for sparse warnings]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The SCCG is a new PLL type introduced on i.MX8.
The description of this SCCG clock can be found here:
https://www.nxp.com/docs/en/reference-manual/IMX8MDQLQRM.pdf#page=834
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This is a new fractional clock type introduced on i.MX8.
The description of this fractional clock can be found here:
https://www.nxp.com/docs/en/reference-manual/IMX8MDQLQRM.pdf#page=834
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add driver for the Clock Control Module found on i.MX8MQ.
Signed-off-by: Anson Huang <anson.huang@nxp.com>
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Since a lot of clocks on imx8m are formed by a mux, gate, predivider and
divider, the idea here is to combine all of those into one composite clock,
but we need to deal with both predivider and divider at the same time and
therefore we add the imx8m_clk_composite_divider_ops and register
the composite clock with those.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Suggested-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
There are clock assignments in all i.MX7D dtb files for UART1,
below is the example in imx7d-sdb.dts, so setting UART1 clock
in clock driver is NOT necessary, actually, module clocks setting
should be done in module driver.
&uart1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart1>;
assigned-clocks = <&clks IMX7D_UART1_ROOT_SRC>;
assigned-clock-parents = <&clks IMX7D_PLL_SYS_MAIN_240M_CLK>;
status = "okay";
};
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
i.MX6Q has MMDC0 ipg clock in CCM CCGR, add it into
clock tree for clock management.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
i.MX6SL has MMDC0 and MMDC1 ipg clock in CCM CCGR, add them into
clock tree for clock management.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
i.MX6SLL has MMDC1 ipg clock in CCM CCGR, add it into
clock tree for clock management.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
i.MX6SX has MMDC1 ipg clock in CCM CCGR, add it into
clock tree for clock management.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
i.MX6UL has MMDC1 ipg clock in CCM CCGR, add it into
clock tree for clock management.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
i.MX7D uses virtual cpu clock of "arm" clock to be child clock
of "arm_a7_root_clk" and it is with CLK_IS_CRITICAL flag set, so
no need to add CLK_IS_CRITICAL flag for keeping "arm_a7_root_clk"
use count correct, latest clock tree is as below in clk_summary:
pll_arm_main 1 1 0 792000000 0
pll_arm_main_bypass 1 1 0 792000000 0
pll_arm_main_clk 1 1 0 792000000 0
arm_a7_src 1 1 0 792000000 0
arm_a7_cg 1 1 0 792000000 0
arm_a7_div 1 1 0 792000000 0
arm_a7_root_clk 1 1 0 792000000 0
arm 1 1 0 792000000
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add CLK_IS_CRITICAL flag for cpu clock type to
make cpu clock use count correct, as cpu clock
should be always critical.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Clock framework will enable those clocks registered
with CLK_IS_CRITICAL flag, so no need to have
clks_init_on array during clock initialization now.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
On i.MX7D, IMX7D_NAND_USDHC_BUS_ROOT_CLK is NOT necessary
for system, and IMX7D_AHB_CHANNEL_ROOT_CLK is NOT existing
at all, remove them from clks_init_on array.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
* clk-imx-critical:
: - Convert to CLK_IS_CRITICAL for i.MX51/53 driver
clk: imx51-imx53: Include sizes.h to silence compile errors
clk: imx51-imx53: Annotate critical clocks as CLK_IS_CRITICAL
* clk-tegra-bpmp:
: - Fix Tegra BPMP driver oops when some xlating a NULL clk
clk: tegra: bpmp: Don't crash when a clock fails to register
* clk-tegra-124:
: - Proper default configuration for vic03 and vde clks on Tegra124
clk: tegra: Make vde a child of pll_c3
clk: tegra: Make vic03 a child of pll_c3
* clk-tegra-critical:
: - Mark Tegra memory controller clks as critical
clk: tegra: Mark Memory Controller clock as critical
* clk-tegra-emc-oob:
: - Fix array bounds clamp in Tegra's emc determine_rate() op
clk: tegra: emc: Avoid out-of-bounds bug
of_find_compatible_node() is returning a device node with refcount
incremented and must be explicitly decremented after the last use
which is right after the us in of_iomap() here.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Fixes: 4a5f720b65 ("clk: imx: add clock driver for imx6sll")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
of_find_compatible_node() is returning a device node with refcount
incremented and must be explicitly decremented after the last use
which is right after the us in of_iomap() here.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Fixes: 787b4271a6 ("clk: imx: add imx6ul clk tree support")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
i.MX6SX has a 16KB always-on ocram bank called
ocram_s, and its clock gate in CCM CCGR1 CG14
needs to be enabled before access, add it to
clock tree.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This driver uses sizes.h, but relies on it being implicitly included
somewhere else breaking random direct compilation of the file. Include
sizes.h so we can build it those configurations too for better compile
coverage.
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Instead of explicitly enabling critical clocks via clk_prepare_enable(),
let's use the standard CLK_IS_CRITICAL flag instead, which makes the code
a bit shorter.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
According to Reference Manual Rev.0, 06/2017, there are GPIO LPCGs
defined in CCM CCGRs, add them into clock tree.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
q/dl datasheets list the 5th selection value for ck01_sel as
video_27M_clk_root.
By replacing the dummy value we then can set IMX6QDL_CLK_VIDEO_27M
as parent for IMX6QDL_CLK_CKO1_SEL.
Signed-off-by: Philipp Puschmann <pp@emlix.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Clock framework will enable those clocks registered
with CLK_IS_CRITICAL flag, so no need to have
clks_init_on array during clock initialization now.
ARM clock is busy divider type which has the
CLK_IS_CRITICAL flag set by default when registered.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
i.MX6UL has GPIO clock gates in CCM CCGR,
add them into clock tree for clock management.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Clock framework will enable those clocks registered
with CLK_IS_CRITICAL flag, so no need to have
clks_init_on array during clock initialization now.
ARM clock is busy divider type which has the
CLK_IS_CRITICAL flag set by default when registered.
IPG clock has no clock gate and its parent AHB clock
is busy divider type, so no need to add CLK_IS_CRITICAL
flag for IPG clock.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Clock framework will enable those clocks registered
with CLK_IS_CRITICAL flag, so no need to have
clks_init_on array during clock initialization now.
ARM clock is busy divider type which has the
CLK_IS_CRITICAL flag set by default when registered.
IPG clock has no clock gate and its parent AHB clock
is busy divider type, so no need to add CLK_IS_CRITICAL
flag for IPG clock.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Clock framework will enable those clocks registered
with CLK_IS_CRITICAL flag, so no need to have
clks_init_on array during clock initialization now.
ARM clock is busy divider type which has the
CLK_IS_CRITICAL flag set by default when registered.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
general cleanups, but nothing too major. The majority of the diff goes to
two SoCs, Actions Semi and Qualcomm. A brand new driver is introduced for
Actions Semi so it takes up some lines to add all the different types, and
the Qualcomm diff is there because we add support for two SoCs and it's quite
a bit of data.
Otherwise the big driver updates are on TI Davinci and Amlogic platforms. And
then the long tail of driver updates for various fixes and stuff follows
after that.
Core:
- debugfs cleanups removing error checking and an unused provider API
- Removal of a clk init typedef that isn't used
- Usage of match_string() to simplify parent string name matching
- OF clk helpers moved to their own file (linux/of_clk.h)
- Make clk warnings more readable across kernel versions
New Drivers:
- Qualcomm SDM845 GCC and Video clk controllers
- Qualcomm MSM8998 GCC
- Actions Semi S900 SoC support
- Nuvoton npcm750 microcontroller clks
- Amlogic axg AO clock controller
Removed Drivers:
- Deprecated Rockchip clk-gate driver
Updates:
- debugfs functions stopped checking return values
- Support for the MSIOF module clocks on Rensas R-Car M3-N
- Support for the new Rensas RZ/G1C and R-Car E3 SoCs
- Qualcomm GDSC, RCG, and PLL updates for clk changes in new SoCs
- Berlin and Amlogic SPDX tagging
- Usage of of_clk_get_parent_count() in more places
- Proper implementation of the CDEV1/2 clocks on Tegra20
- Allwinner H6 PRCM clock support and R40 EMAC support
- Add critical flag to meson8b's fdiv2 as temporary fixup for ethernet
- Round closest support for meson's mpll driver
- Support for meson8b nand clocks and gxbb video decoder clocks
- Mediatek mali clks
- STM32MP1 fixes
- Uniphier LD11/LD20 stream demux system clock
-----BEGIN PGP SIGNATURE-----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=KK/v
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This time we have a good set of changes to the core framework that do
some general cleanups, but nothing too major. The majority of the diff
goes to two SoCs, Actions Semi and Qualcomm. A brand new driver is
introduced for Actions Semi so it takes up some lines to add all the
different types, and the Qualcomm diff is there because we add support
for two SoCs and it's quite a bit of data.
Otherwise the big driver updates are on TI Davinci and Amlogic
platforms. And then the long tail of driver updates for various fixes
and stuff follows after that.
Core:
- debugfs cleanups removing error checking and an unused provider API
- Removal of a clk init typedef that isn't used
- Usage of match_string() to simplify parent string name matching
- OF clk helpers moved to their own file (linux/of_clk.h)
- Make clk warnings more readable across kernel versions
New Drivers:
- Qualcomm SDM845 GCC and Video clk controllers
- Qualcomm MSM8998 GCC
- Actions Semi S900 SoC support
- Nuvoton npcm750 microcontroller clks
- Amlogic axg AO clock controller
Removed Drivers:
- Deprecated Rockchip clk-gate driver
Updates:
- debugfs functions stopped checking return values
- Support for the MSIOF module clocks on Rensas R-Car M3-N
- Support for the new Rensas RZ/G1C and R-Car E3 SoCs
- Qualcomm GDSC, RCG, and PLL updates for clk changes in new SoCs
- Berlin and Amlogic SPDX tagging
- Usage of of_clk_get_parent_count() in more places
- Proper implementation of the CDEV1/2 clocks on Tegra20
- Allwinner H6 PRCM clock support and R40 EMAC support
- Add critical flag to meson8b's fdiv2 as temporary fixup for ethernet
- Round closest support for meson's mpll driver
- Support for meson8b nand clocks and gxbb video decoder clocks
- Mediatek mali clks
- STM32MP1 fixes
- Uniphier LD11/LD20 stream demux system clock"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (134 commits)
clk: qcom: Export clk_fabia_pll_configure()
clk: bcm: Update and add Stingray clock entries
dt-bindings: clk: Update Stingray binding doc
clk-si544: Properly round requested frequency to nearest match
clk: ingenic: jz4770: Add 150us delay after enabling VPU clock
clk: ingenic: jz4770: Enable power of AHB1 bus after ungating VPU clock
clk: ingenic: jz4770: Modify C1CLK clock to disable CPU clock stop on idle
clk: ingenic: jz4770: Change OTG from custom to standard gated clock
clk: ingenic: Support specifying "wait for clock stable" delay
clk: ingenic: Add support for clocks whose gate bit is inverted
clk: use match_string() helper
clk: bcm2835: use match_string() helper
clk: Return void from debug_init op
clk: remove clk_debugfs_add_file()
clk: tegra: no need to check return value of debugfs_create functions
clk: davinci: no need to check return value of debugfs_create functions
clk: bcm2835: no need to check return value of debugfs_create functions
clk: no need to check return value of debugfs_create functions
clk: imx6: add EPIT clock support
clk: mvebu: use correct bit for 98DX3236 NAND
...
