Currently multi-channel configuration is read via the QUERY_FW_CONFIG cmd.
This method has been deprecated by the Skyhawk-R FW. Instead,
GET_PROFILE_CONFIG::port-desc must be used to query this configuration.
This patch also:
a) introduces a few macros to identify certain categories of multi-channel
configs
2) re-factors the be_cmd_set_profile_config() code to be able to read any kind
of desc (and not just the nic-desc.)
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The use of NTKW_MAC_QUERY cmd has been deprecated for Skyhawk-R.
Replace the last remaining usage in be_vfs_mac_query() routine.
Signed-off-by: Suresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An earlier commit (f25b119c "Fix error messages while driver load for VFs")
incorrectly set the adapter->cmd_privileges value for VFs (in a
multi-channel config) to MAX_PRIVILEGES. This causes FW cmd failures
and avoidable error logs when certian cmds are issued by a VF.
Also, move the multi-channel hack to be_cmds.c inside
be_cmd_get_fn_privileges() routine.
Fixes: f25b119c "Fix error messages while driver load for VFs"
Signed-off-by: Suresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Skyhawk-R FW does not support SET/GET_EXT_FAT_CAPABILITIES cmds via which
FW logging level can be controlled. Also, the hack used in BE3 to control
FW logging level via the ethtool interface is not needed in Skyhawk-R.
This patch also cleans up this code by moving be_set/get_fw_log_level()
routines to be_cmds.c where they belong.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
remove new line
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently this cmd is used only for Lancer.
MCC_CREATE_EXT_V1 supports larger CQ-ids and additional event codes for the
async_event_bitmap field.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver currently requests the firmware to enable rx_interface options
without considering if the interface was created with that capability.
This could cause commands to firmware to fail.
To avoid this, enable only those options on an interface if the interface
was created with that capability.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function needn't to be public, so to make it as static.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moving to version 2 of GET_STATS command as SkyHawk-R supports
higher number of rings.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/emulex/benet/be.h
drivers/net/usb/qmi_wwan.c
drivers/net/wireless/brcm80211/brcmfmac/dhd_bus.h
include/net/netfilter/nf_conntrack_synproxy.h
include/net/secure_seq.h
The conflicts are of two varieties:
1) Conflicts with Joe Perches's 'extern' removal from header file
function declarations. Usually it's an argument signature change
or a function being added/removed. The resolutions are trivial.
2) Some overlapping changes in qmi_wwan.c and be.h, one commit adds
a new value, another changes an existing value. That sort of
thing.
Signed-off-by: David S. Miller <davem@davemloft.net>
The current EQ delay calculation for AIC is based only on RX packet rate.
This fails to be effective when there's only TX and no RX.
This patch inclues:
- Calculating EQ-delay based on both RX and TX pps.
- Modifying EQ-delay of all EQs via one cmd, instead of issuing a separate
cmd for each EQ.
- A new structure to store interrupt coalescing parameters, in a separate
cache-line from the EQ-obj.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the interface runs out of the allocated entries in VLAN table,
we program the interface in VLAN promiscuous mode.
Use OPCODE_COMMON_NTWK_RX_FILTER to set VLAN Promiscuous mode
instead of OPCODE_COMMON_NTWK_VLAN_CONFIG.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Size of be_nic_res_desc structure is incorrect. Fix it.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a mix of function prototypes with and without extern
in the kernel sources. Standardize on not using extern for
function prototypes.
Function prototypes don't need to be written with extern.
extern is assumed by the compiler. Its use is as unnecessary as
using auto to declare automatic/local variables in a block.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SkyHawk-R can support VEB or VEPA mode.
This patch will allow the user to set/query this switch setting.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1) use be_resources{} struct to query/store HW resource limits
2) The HW queue/resource limits for BE2/BE3 chips are mostly called out
in driver as constants. Code to handle this is scattered across various
places in be_setup(). Consolidate this code into BEx_get_resources().
For Lancer-R, Skyhawk-R, these limits are queried from FW.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1) Parse PCIe descriptor for max-VFs supported by HW
2) Cleanup NIC descriptor parsing in get_func/profile_config() routines
3) Use common struct definitions for v0 and v1 versions of GET_FUNC_CONFIG
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
EQ_CREATEv2 explicitly returns the msix-index associated with a EQ.
For SH-R this is needed if EQs need to be deleted and re-created without
resetting a function.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible for some versions of firmware to advertise capabilities that driver
is not ready to handle. This may lead to controller stall. Since the driver is
interested only in subset of flags, clearing the rest.
Signed-off-by: Sarveshwar Bandi <sarveshwar.bandi@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new speeds are supported by variants of the Skyhawk-R chip.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On SH-R and Lancer-R, GET_MAC_LIST cmd is better supported
(instead of NTWK_MAC_QUERY cmd) to query provisioned MAC addresses.
Similiarly, (on SH-R and Lancer-R) SET_MAC_LIST must be used by the PF to
provision a permanent MAC addresses to the VF.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code to configure the permanent MAC in be_setup() has become quite
complicated, with different FW cmds being used for BEx, SH-R and Lancer.
Simplify the logic by moving some of this complexity to be_cmds.c. This
makes the code in be_setup() a little more readable.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the current design VFs were not allowed to program MAC/VLAN filters.
Only the PF driver was allowed to configure/provision MAC and transparent
VLANs to a VF. Change this to support MAC/VLAN filtering on a VF by a VM.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the VFs by default don't have the privilege to modify MAC address.
This will change in a subsequent fix wherein VFs will have the ability to
modify MAC/VLAN filters.
Fix be_mac_addr_set() logic to support MAC address modification on a
privileged VF too.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added code to initiate FW dump via ethtool. Driver checks if the previous dump
has been cleared before initiating the dump. It doesn't initiate the dump
if it is not cleared.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SkyHawk-R devices should use v2 of cq_create command.
BE3/BE2 devices can use version 0 of the command to create a CQ.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
drivers/net/ethernet/emulex/benet/be.h
include/net/tcp.h
net/mac802154/mac802154.h
Most conflicts were minor overlapping stuff.
The be2net driver brought in some fixes that added __vlan_put_tag
calls, which in net-next take an additional argument.
Signed-off-by: David S. Miller <davem@davemloft.net>
Skyhawk-R requires V1 version of GET_FUNCTION_CONFIG cmd to be used for
querrying resources available per function.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Suresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: Sarveshwar Bandi <sarveshwar.bandi@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Suresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: Sarveshwar Bandi <sarveshwar.bandi@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ASIC could lockup in the transmit path when it tries
to insert VLAN in a specific ipv6 packet.
1) Identify the packet which can cause this.
2) Check if the firmware provides a workaround to prevent this.
3) If workaround is not present, drop the packet.
4) If the firmware provides a workaround, insert the VLAN tag in the
packet and inform the firmware to skip further VLAN insertions.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use GET_PROFILE_CONFIG_V1 cmd for BE3-R, to query the maximum number of
TX rings available per function. On SH-R the same is queried via the
GET_FUNCTION_CONFIG cmd.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid flashing BE3 UFI on BE3-R chip by verifying asic_revision
number of the chip.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Skyhawk-R and BE3-R (SuperNIC profile) require V2 version
of TXQ_CREATE cmd to be used.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is needed as the earlier method of manipulating this register via PCI
Config space is disallowed by certain Hypervisors.
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sarveshwar Bandi <sarveshwar.bandi@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when the PF driver is unloaded and re-loaded while VFs are attached
to VMs, it loses control of its VFs.
The PF driver now uses the newly defined/created GET_IFACE_LIST cmd
(available in FW ver >= 4.6) to query the if_id of the VFs
(enabled in its previous life). The PF driver then uses the if_id for
further VF configuration.
The GET_IFACE_MAC_LIST cmd has also implemented in BE3 FW for PF to
query pmac-ids used by its VFs.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
adapter->generation was being incorrectly set as BE_GEN3 for Skyhawk-R.
Replace generation usage with XXX_chip() macros to identify the chip.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FW flashing code, even though it works correctly, makes some hidden
assumptions about buffer sizes. This is causing code analysers to
report error. Cleanup FW flashing code to remove these hidden assumptions.
Reported-by: Yuanhan Liu <yuanhan.liu@intel.com>
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PF driver should enable VF so that VF goes to ready state in
new Lancer FW.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VF does not have privileges to execute many commands. When VFs try
to execute those commands there are unnecessary error messages.
Fix this by executing only those commands for which VF has privilege.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use Lancer specific command to set QoS for VF.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver assumes FW resource counts and capabilities while creating queues and
using functionality like RSS. This causes driver load to fail in FW configs
where resources and capabilities are reduced. Fix this by querying FW
configuration during probe and using resources and capabilities accordingly.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1) link_status_query() is always called to query the link-speed (speed
after applying qos). When there is no qos setting, link-speed is derived from
port-speed. Do all this inside this routine and hide this from the callers.
2) adpater->phy.forced_port_speed is not being set anywhere after being
initialized. Get rid of this variable.
3) Ignore async link_speed notifications till the initial value has been
fetched from FW.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All invocations of this routine use the same type value.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ability of driver to transmit packets depends on logical state
of the link. Ignore physical link status.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Incorporated review comment from Eric Dumazet. Added description
about different RSS hash types which adapter is capable of.
Will add support for ETHTOOL_GRXFH and ETHTOOL_SRXFX as suggested
by Ben Hutchings in a later patch.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
