This fixes the following warning by also sending the flags argument for
gpio controllers:
Property 'cs-gpios', cell 6 is not a phandle reference in
/ahb/apb/spi@e0100000
Fixes: 8113ba917d ("ARM: SPEAr: DT: Update device nodes")
Cc: stable@vger.kernel.org # v3.8+
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
The "dmas" cells for the designware DMA controller need to have only 3
properties apart from the phandle: request line, src master and
destination master. But the commit 6e8887f60f updated it incorrectly
while moving from platform code to DT. Fix it.
Cc: stable@vger.kernel.org # v3.10+
Fixes: 6e8887f60f ("ARM: SPEAr13xx: Pass generic DW DMAC platform data from DT")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
dtc complains about the lack of #coolin-cells properties for the
CPU nodes that are referred to as "cooling-device":
arch/arm64/boot/dts/mediatek/mt8173-evb.dtb: Warning (cooling_device_property): Missing property '#cooling-cells' in node /cpus/cpu@0 or bad phandle (referred from /thermal-zones/cpu_thermal/cooling-maps/map@0:cooling-device[0])
arch/arm64/boot/dts/mediatek/mt8173-evb.dtb: Warning (cooling_device_property): Missing property '#cooling-cells' in node /cpus/cpu@100 or bad phandle (referred from /thermal-zones/cpu_thermal/cooling-maps/map@1:cooling-device[0])
Apparently this property must be '<2>' to match the binding.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
A few improvements to our DT support, with:
- basic DRM support for the A83t
- simplefb support for the H3 and H5 SoCs
- One fix for the USB ethernet on the Orange Pi R1
-----BEGIN PGP SIGNATURE-----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=bDG2
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-4.16-2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Allwinner DT changes for 4.16, bis
A few improvements to our DT support, with:
- basic DRM support for the A83t
- simplefb support for the H3 and H5 SoCs
- One fix for the USB ethernet on the Orange Pi R1
* tag 'sunxi-dt-for-4.16-2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sun8i: a711: Enable the LCD
ARM: dts: sun8i: a83t: Add LVDS pins group
ARM: dts: sun8i: a83t: Enable the PWM
ARM: dts: sun8i: a83t: Add display pipeline
ARM: sunxi: h3/h5: add simplefb nodes
arm64: allwinner: h5: add compatible string for DE2 CCU
ARM: sun8i: h3/h5: add DE2 CCU device node for H3
dt-bindings: simplefb-sunxi: add pipelines for DE2
ARM: dts: sun8i: fix USB Ethernet of Orange Pi R1
Signed-off-by: Olof Johansson <olof@lixom.net>
include IR, SPI and ethernet MAC support for the new AXG family SoCs.
-----BEGIN PGP SIGNATURE-----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=lk2H
-----END PGP SIGNATURE-----
Merge tag 'amlogic-dt64-3' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into next/dt
Another round of 64-bit DT changes for the new Amlogic SoCs. These
include IR, SPI and ethernet MAC support for the new AXG family SoCs.
* tag 'amlogic-dt64-3' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
ARM64: dts: meson-axg: enable ethernet for A113D S400 board
ARM64: dts: meson-axg: add ethernet mac controller
ARM64: dts: meson-axg: add the SPICC controller
ARM64: dts: meson-axg: enable IR controller
arm64: dts: meson-axg: switch uart_ao clock to CLK81
clk: meson-axg: add clocks dt-bindings required header
dt-bindings: clock: add compatible variant for the Meson-AXG
Signed-off-by: Olof Johansson <olof@lixom.net>
According to the comment added to exynos_dt_pmu_match[] in commit
8b283c0254 ("ARM: exynos4/5: convert pmu wakeup to stacked domains"),
the RTC is not able to wake up the system through the PMU on Exynos5410,
unlike Exynos5420.
However, when the RTC DT node got added, it was a straight copy of
the Exynos5420 node, which now causes a warning from dtc.
This removes the incorrect interrupt-parent, which should get the
interrupt working and avoid the warning.
Fixes: e1e146b1b0 ("ARM: dts: exynos: Add RTC and I2C to Exynos5410")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This reverts commit 6737b08140.
Unlike on Exynos5420-family, on Exynos5410 the PMU is not an interrupt
controller so it should not handle interrupts of RTC. The DTC warning
(addressed by mentioned commit) should be fixed by not routing RTC
interrupts to PMU.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This is tested in the S400 dev board which use a RTL8211F PHY,
and the pins connect to the 'eth_rgmii_y_pins' group.
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add DT info for the stmmac ethernet MAC which found in
the Amlogic's Meson-AXG SoC, also describe the ethernet
pinctrl & clock information here.
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add DT info for the SPICC controller which found in
the Amlogic's Meson-AXG SoC.
Signed-off-by: Sunny Luo <sunny.luo@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Enable IR remote controller which found in Amlogic's Meson-AXG SoCs.
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Switch the uart_ao pclk to CLK81 since the clock driver is ready.
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The main change here are the series of commits doing the Armada 7K/8K
CP110 DT de-duplication, they include the de-duplication itself and
small fixes in the device tree files.
Besides them there are 2 other patches:
- One adding the crypto support for Armada 37xx SoCs
- An other adding Ethernet aliases on A7K/A8K base boards
-----BEGIN PGP SIGNATURE-----
iIEEABECAEEWIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCWk+h0CMcZ3JlZ29yeS5j
bGVtZW50QGZyZWUtZWxlY3Ryb25zLmNvbQAKCRALBhiOFHI71ZU9AKCNLcEcewii
UWPVUzEsQ/+UPojO4wCdHqum9OT33XChVrxHGKP89Dnj1ro=
=HCIC
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt64-4.16-2' of git://git.infradead.org/linux-mvebu into next/dt
Pull "mvebu dt64 for 4.16 (part 2)" from Gregory CLEMENT:
The main change here are the series of commits doing the Armada 7K/8K
CP110 DT de-duplication, they include the de-duplication itself and
small fixes in the device tree files.
Besides them there are 2 other patches:
- One adding the crypto support for Armada 37xx SoCs
- An other adding Ethernet aliases on A7K/A8K base boards
* tag 'mvebu-dt64-4.16-2' of git://git.infradead.org/linux-mvebu:
arm64: dts: marvell: add Ethernet aliases
arm64: dts: marvell: replace cpm by cp0, cps by cp1
arm64: dts: marvell: de-duplicate CP110 description
arm64: dts: marvell: use aliases for SPI busses on Armada 7K/8K
arm64: dts: marvell: use mvebu-icu.h where possible
arm64: dts: marvell: fix compatible string list for Armada CP110 slave NAND
arm64: dts: marvell: fix typos in comment describing the NAND controller
arm64: dts: marvell: use lower case for unit address and reg property
arm64: dts: marvell: fix watchdog unit address in Armada AP806
arm64: dts: marvell: armada-37xx: add a crypto node
ARM64: dts: marvell: armada-cp110: Fix clock resources for various node
ARM: dts: kirkwood: fix pin-muxing of MPP7 on OpenBlocks A7
- A few random updates for vf610-zii board: correct switch EEPROM size,
enable edma1, correct GPIO expander interrupt, add PHYs for switch2
device.
- LS1021A device tree updates: add reboot and QSPI device nodes, label
USB controllers, specify interrupt-affinity for PMU, fix TMR_FIPER1
setting, enable esdhc device, add Moxa UC-8410A board support.
- A bunch of patches from Fabio: fix reg - unit address mismatches,
remove leading zero in unit address, move regulators out of
simple-bus, move nodes with no reg property out of bus, remove extra
clock cell, add missing phy-cells to usb-nop-xceiv, etc.
- A couple series from Hummingboard developers: re-organise device tree
files for better handling various board versions, and then add the
new hummingboard2 board support on top of that.
- Disable AC'97 input pins pad and add support for powering off for
imx6qdl-udoo board.
- Convert from fbdev to drm bindings for imx6sx-sdb and imx6sl-evk
board.
- Add device tree for Variscite DART-MX6 SoM and Carrier-board support.
- Add new board support of TS-4600 and TS-7970 from Technologic
Systems.
- A series from Stefan to update imx7-colibri device tree and then add
new version of Toradex Colibri iMX7D board with eMMC support.
- Other random updates on various board support.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJaTDRSAAoJEFBXWFqHsHzO5qwIAJ9iqSd41KE50kX2QPWa6Uqa
Dfj0BcR4RdFpf4FqCOM6ntjVhUEyxNUtwINuMr6eCI8BK1NGeLNJGm9LK77/RwoE
wmUFTcGelzx4iEWVouD1NoCxIvVFm5RyO26JC/0GPUbulKvcTRma+GQBV218ZOcz
5GYZ2vlmvddwfgNCF+w2tRB07s5kFKWk9S+w7oDd2qF4qztOzBWMr+i5gdtLAboc
iaWS1+9RQu1FbtuanHAbCFmaQrPV2YsDnnIQYMBqpKlFoO7oUSJCDkINWy0BXq7f
eXXLj/hwc8cAC0MM5kuvScEcgKth0p7W0kQETzC19v1EFYx1CxFwFjxXYQ16iCQ=
=1F3D
-----END PGP SIGNATURE-----
Merge tag 'imx-dt-4.16' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
Pull "i.MX device tree changes for 4.16" from Shawn Guo:
- A few random updates for vf610-zii board: correct switch EEPROM size,
enable edma1, correct GPIO expander interrupt, add PHYs for switch2
device.
- LS1021A device tree updates: add reboot and QSPI device nodes, label
USB controllers, specify interrupt-affinity for PMU, fix TMR_FIPER1
setting, enable esdhc device, add Moxa UC-8410A board support.
- A bunch of patches from Fabio: fix reg - unit address mismatches,
remove leading zero in unit address, move regulators out of
simple-bus, move nodes with no reg property out of bus, remove extra
clock cell, add missing phy-cells to usb-nop-xceiv, etc.
- A couple series from Hummingboard developers: re-organise device tree
files for better handling various board versions, and then add the
new hummingboard2 board support on top of that.
- Disable AC'97 input pins pad and add support for powering off for
imx6qdl-udoo board.
- Convert from fbdev to drm bindings for imx6sx-sdb and imx6sl-evk
board.
- Add device tree for Variscite DART-MX6 SoM and Carrier-board support.
- Add new board support of TS-4600 and TS-7970 from Technologic
Systems.
- A series from Stefan to update imx7-colibri device tree and then add
new version of Toradex Colibri iMX7D board with eMMC support.
- Other random updates on various board support.
* tag 'imx-dt-4.16' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (126 commits)
ARM: dts: imx7s: Avoid using label in unit address and reg
ARM: dts: imx51-zii-rdu1: Add missing #phy-cells to usb-nop-xceiv
ARM: dts: imx6qdl-hummingboard2: Remove leading zero in unit address
ARM: dts: ls1021a: add support for Moxa UC-8410A open platform
ARM: dts: imx51-babbage: Fix the 26MHz clock modelling
ARM: dts: vf610-zii-dev-rev-b: add PHYs for switch2
ARM: dts: vf610-zii-dev-rev-b: fix interrupt for GPIO expander
ARM: dts: vf610-zii-dev: enable edma1
ARM: dts: ls1021a-twr: Remove extra clock cell
ARM: dts: ls1021a-qds: Remove extra clock cell
ARM: dts: imx53: add srtc node
dt-bindings: imx-gpcv2: Fix the unit address
ARM: imx: dts: Use lower case for bindings notation
ARM: dts: imx6q-h100: use usdhc2 VSELECT
ARM: dts: imx6sx: Add support for PCI power domain
ARM: dts: imx6sx: Fix PCI non-prefetchable memory range
ARM: dts: imx6qdl-hummingboard2: rename regulators to match schematic
ARM: dts: imx6qdl-hummingboard2: add v1.5 som with eMMC
ARM: dts: imx6qdl-hummingboard2: add v1.5 som without eMMC
ARM: dts: imx6qdl-hummingboard2: add PWM3 support
...
Clock driver support:
Rework all platforms to use proper clock bindings. Linux should now boot
upstream kernels on ast2400 and ast2500 platforms without out of tree
patches.
New systems:
Witherspoon: OpenPower Power9 server manufactured by IBM that uses the ASPEED ast2500
Zaius: OpenPower Power9 server manufactured by Invatech that uses the ASPEED ast2500
Q71L: Intel Xeon server manufactured by Qanta that uses the ASPEED ast2400
We also see updates to the Palmetto and Romulus systems to bring them in
line with the functionality of those above.
The systems take advantage of recently added drivers for LPC Snoop
device and the PWM/Tachometer fan controller.
OpenBMC flash layout:
The flash layout used OpenBMC systems is added and the device trees now
use it.
-----BEGIN PGP SIGNATURE-----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=H9im
-----END PGP SIGNATURE-----
Merge tag 'aspeed-4.16-devicetree' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/joel/aspeed into next/dt
Pull "ASPEED device tree updates for 4.16" from Joel Stanley:
Clock driver support:
Rework all platforms to use proper clock bindings. Linux should now boot
upstream kernels on ast2400 and ast2500 platforms without out of tree
patches.
New systems:
Witherspoon: OpenPower Power9 server manufactured by IBM that uses the ASPEED ast2500
Zaius: OpenPower Power9 server manufactured by Invatech that uses the ASPEED ast2500
Q71L: Intel Xeon server manufactured by Qanta that uses the ASPEED ast2400
We also see updates to the Palmetto and Romulus systems to bring them in
line with the functionality of those above.
The systems take advantage of recently added drivers for LPC Snoop
device and the PWM/Tachometer fan controller.
OpenBMC flash layout:
The flash layout used OpenBMC systems is added and the device trees now
use it.
* tag 'aspeed-4.16-devicetree' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/joel/aspeed:
ARM: dts: aspeed-evb: Add unit name to memory node
ARM: dts: aspeed-plametto: Add flash layout and fix memory node
ARM: dts: aspeed-romulus: Update Romulus system
ARM: dts: aspeed: Add Qanta Q71L BMC machine
ARM: dts: aspeed: Add Ingrasys Zaius BMC machine
ARM: dts: aspeed: Add Witherspoon BMC machine
ARM: dts: aspeed: Sort ASPEED entries in makefile
ARM: dts: Add OpenBMC flash layout
ARM: dts: aspeed: Update license headers
ARM: dts: aspeed: Remove skeleton.dtsi
ARM: dts: aspeed: Add LPC Snoop device
ARM: dts: aspeed: Add PWM and tachometer node
ARM: dts: aspeed: Add clock phandle to GPIO
ARM: dts: aspeed: Add flash controller clocks
ARM: dts: aspeed: Add watchdog clocks
ARM: dts: aspeed: Add MAC clocks
ARM: dts: aspeed: Add proper clock references
ARM: dts: aspeed: Add LPC and child devices
dt-bindings: gpio: Add ASPEED constants
dt-bindings: clock: Add ASPEED constants
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch adds Ethernet aliases in the Marvell Armada 7040 DB, 8040 DB
and 8040 mcbin device trees so that the bootloader setup the MAC
addresses correctly.
Signed-off-by: Yan Markman <ymarkman@marvell.com>
[Antoine: commit message, small fixes]
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
In preparation for the introduction of more than 2 CPs in upcoming
SoCs, it makes sense to move away from the "CP master" (cpm) and "CP
slave" (cps) naming, and use instead cp0/cp1.
This commit is the result of:
sed 's%cpm%cp0g%' arch/arm64/boot/dts/marvell/*
sed 's%cps%cp1g%' arch/arm64/boot/dts/marvell/*
So it is a purely mechaninal change.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Suggested-by: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
One concept of Marvell Armada 7K/8K SoCs is that they are made of HW
blocks composed of a variety of IPs (network, PCIe, SATA, XOR, SPI,
I2C, etc.), and those HW blocks can be duplicated several times within
a given SoC. The Armada 7K SoC has a single CP110 (so no duplication),
while the Armada 8K SoC has two CP110. In the future, SoCs with more
than 2 CP110s will be introduced.
In current kernel versions, the master CP110 is described in
armada-cp110-master.dtsi and the slave CP110 is described in
armada-cp110-slave.dtsi. Those files are basically exactly the same,
since they describe the same hardware. They only have a few
differences:
- Base address of the registers is different for the "config-space"
- Base address of the PCIe registers, MEM, CONF and IO areas were
different
- Labels (and phandles pointing to them) of the nodes were different
("cpm" prefix in the master CP, "cps" prefix in the slave CP)
This duplication issue has been discussed at the DT workshop [1] in
Prague last October, and we presented on this topic [2]. The solution
of using the C pre-processor to avoid this duplication has been
validated by the people present in this DT workshop, and this patch
simply implements what has been presented.
We handle differences between the master CP and slave CP description
using the C pre-processor, by defining a set of macros with different
values armada-cp110.dtsi is included to instantiate one of the master
or slave CP110.
There are a few aspects that deserve additional explanations:
- PCIe needs to be handled separately because it is not part of the
config-space {...} node, since it has registers outside of the
range covered by config-space {...}.
- We need to defined CP110_BASE, CP110_PCIEx_BASE without 0x, because
they are used for the unit address part of some DT nodes. But since
they are also used for the "reg" property of the same nodes, we
have an ADDRESSIFY() macro that prepends 0x to those values.
We compared the resulting .dtb for armada-8040-db.dtb before and after
this patch is applied, and the result is exactly the same, except for
a few differences:
- the SDHCI controller that was only described in the master CP110 is
now also described in the slave CP110. Even though the SDHCI
controller from the slave CP110 is indeed not usable (as it isn't
wired to the outside world) it is technically part of the silicon,
and therefore it is reasonable to also describe it to be part of
the slave CP110. In addition, if we wanted to get this correct for
the SDHCI controller, we should also do it for the NAND controller,
for which the situation is even more complicated: in a single CP110
configuration (Armada 7K), the usable NAND controller is in the
master CP110, while in a dual CP110 configuration (Armada 8K), the
usable NAND controller is in the slave CP110. Since that would add
a lot of additional complexity for no good reason, and since the IP
blocks are in fact really present in both CPs, we simply describe
them in both CPs at the DT level.
- the cp110-master and cp110-slave nodes are now named cpm and
cps. We could have kept cp110-master and cp110-slave, but that
would have required adding another CP110_xyz define, which didn't
seem very useful.
Note that this commit also gets rid of the armada-cp110-master.dtsi
and armada-cp110-slave.dtsi files, as future SoCs will have more than
2 CPs. Instead, we instantiate the CPs directly from the SoC-specific
.dtsi files, i.e armada-70x0.dtsi and armada-80x0.dtsi.
[1] https://elinux.org/Device_tree_kernel_summit_2017_etherpad
[2] https://elinux.org/images/1/14/DTWorkshop2017-duplicate-data.pdf
[gregory.clement@free-electrons.com: add back the "ARM64: dts: marvell:
Fix clock resources for various node" commit]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
We are currently using the cell-index DT property to assign SPI bus
numbers. This property is specific to the spi-orion driver, and
requires each SPI controller to have a unique ID defined in the Device
Tree.
As we are about to merge armada-cp110-master.dtsi and
armada-cp110-slave.dtsi into a single file, those cell-index
properties that differ between the master CP110 and the slave CP110
are a difference that would have to be handled.
In order to avoid this, we switch to using the "aliases" DT node to
assign a unique number to each SPI controller. This is more generic,
and directly handled by the SPI core.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Back when the ICU Device Tree binding was introduced, we could not use
mvebu-icu.h from the Device Tree files, because the DT files and
mvebu-icu.h were following different merge routes towards Linus
tree. Now that both have been merged, we can switch the Marvell Armada
CP110 Device Tree files to use the mvebu-icu.h header instead of
duplicating the ICU_GRP_NSR definition.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The Armada CP110 slave NAND controller Device Tree description lists
the compatible string in the wrong order: marvell,armada-8k-nand
should come first. This commit alignes the slave CP110 description
with the master CP110 description from that respect.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Fix the same typo duplicated in both master and slave version of
armada-cp110-*.dtsi file: s/limiation/limitation/.
[gregory.clement@free-electrons.com: add the commit log]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This fixes the following DTC warning:
<stdout>: Warning (simple_bus_reg): Node /ap806/config-space@f0000000/thermal@6f808C simple-bus unit address format error, expected "6f808c"
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This fixes the following DTC warning:
Warning (simple_bus_reg): Node /ap806/config-space@f0000000/watchdog@600000 simple-bus unit address format error, expected "610000"
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This patch adds a crypto node describing the EIP97 engine found in
Armada 37xx SoCs. The cryptographic engine is enabled by default.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
On the CP modules we found on Armada 7K/8K, many IP block actually also
need a "functional" clock (from the bus). This patch add them which allows
to fix some issues hanging the kernel:
If Ethernet and sdhci driver are built as modules and sdhci was loaded
first then the kernel hang.
Fixes: bb16ea1742 ("mmc: sdhci-xenon: Fix clock resource by adding an
optional bus clock")
Cc: stable@vger.kernel.org
Reported-by: Riku Voipio <riku.voipio@linaro.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
- clock, pinctrl, PWM and reset nodes for new AXG SoC family
-----BEGIN PGP SIGNATURE-----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=4k+i
-----END PGP SIGNATURE-----
Merge tag 'amlogic-dt64-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into next/dt
Pull "Amlogic 64-bit DT updates for v4.16, round 2" from Kevin Hilman:
This adds a few more basics (clock, pinctrl, PWM, reset) for the new AXG
family of Amlogic SoCs.
* tag 'amlogic-dt64-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
arm64: dts: meson-axg: add new reset DT node
ARM64: dts: meson-axg: add PWM DT info for Meson-Axg SoC
ARM64: dts: meson-axg: add pinctrl DT info for Meson-AXG SoC
documentation: Add compatibles for Amlogic Meson AXG pin controllers
arm64: dts: meson-axg: add clock DT info for Meson AXG SoC
The A711 has 1024x600 LVDS panel, with a PWM-based backlight. Add it to our
DT.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
MPP7 is currently muxed as "gpio", but this function doesn't exist for
MPP7, only "gpo" is available. This causes the following error:
kirkwood-pinctrl f1010000.pin-controller: unsupported function gpio on pin mpp7
pinctrl core: failed to register map default (6): invalid type given
kirkwood-pinctrl f1010000.pin-controller: error claiming hogs: -22
kirkwood-pinctrl f1010000.pin-controller: could not claim hogs: -22
kirkwood-pinctrl f1010000.pin-controller: unable to register pinctrl driver
kirkwood-pinctrl: probe of f1010000.pin-controller failed with error -22
So the pinctrl driver is not probed, all device drivers (including the
UART driver) do a -EPROBE_DEFER, and therefore the system doesn't
really boot (well, it boots, but with no UART, and no devices that
require pin-muxing).
Back when the Device Tree file for this board was introduced, the
definition was already wrong. The pinctrl driver also always described
as "gpo" this function for MPP7. However, between Linux 4.10 and 4.11,
a hog pin failing to be muxed was turned from a simple warning to a
hard error that caused the entire pinctrl driver probe to bail
out. This is probably the result of commit 6118714275 ("pinctrl:
core: Fix pinctrl_register_and_init() with pinctrl_enable()").
This commit fixes the Device Tree to use the proper "gpo" function for
MPP7, which fixes the boot of OpenBlocks A7, which was broken since
Linux 4.11.
Fixes: f24b56cbcd ("ARM: kirkwood: add support for OpenBlocks A7 platform")
Cc: <stable@vger.kernel.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The EB MP board probably has a character LCD but the board manual does
not really state which IRQ it has assigned to this device. The invalid
assignment was a mistake by me during submission of the DTSI where I was
looking for the reference, didn't find it and didn't fill it in.
Delete this for now: it can probably be fixed but that requires access
to the actual board for some trial-and-error experiments.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
- New boards:
- Axentia Nattis with Natte power
- sama5d2 PTC ek
- Document and use extended TCB bindings
-----BEGIN PGP SIGNATURE-----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=BW4/
-----END PGP SIGNATURE-----
Merge tag 'at91-ab-4.16-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux into next/dt
DT for 4.16
- New boards:
- Axentia Nattis with Natte power
- sama5d2 PTC ek
- Document and use extended TCB bindings
* tag 'at91-ab-4.16-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (50 commits)
ARM: dts: at91: sama5d2_ptc_ek: use TCB0 as timers
ARM: dts: at91: sama5d27_som1_ek: use TCB0 as timers
ARM: dts: at91: sama5d2 Xplained: use TCB0 as timers
ARM: dts: at91: sama5d2: TC blocks are also simple-mfd and syscon devices
ARM: dts: at91: vinco: use TCB2 as timers
ARM: dts: at91: ma5d4: use TCB2 as timers
ARM: dts: at91: sama5d4 Xplained: use TCB2 as timers
ARM: dts: at91: sama5d4ek: use TCB2 as timers
ARM: dts: at91: sama5d4: Add TCB2
ARM: dts: at91: sama5d4: TC blocks are also simple-mfd and syscon devices
ARM: dts: at91: linea/tse850-3: use TCB0 as timers
ARM: dts: at91: sama5d3xek_cmp: use TCB0 as timers
ARM: dts: at91: kizbox2: use TCB0 as timers
ARM: dts: at91: sama5d3 Xplained: use TCB0 as timers
ARM: dts: at91: sama5d3xek: use TCB0 as timers
ARM: dts: at91: sama5d3: TC blocks are also simple-mfd and syscon devices
ARM: dts: at91: kizboxmini: use TCB0 as timers
ARM: dts: at91: cosino: use TCB0 as timers
ARM: dts: at91: acme/g25: use TCB0 as timers
ARM: dts: at91: at91sam9x5cm: use TCB0 as timers
...
Signed-off-by: Olof Johansson <olof@lixom.net>
- clean up gpios properties by macro
- add GPIO hog for PXs3 reference node
- add has-transaction-translator property to generic-ehci nodes
- enable more serial ports for PXs3 reference node
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=kgZ1
-----END PGP SIGNATURE-----
Merge tag 'uniphier-dt64-v4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier into next/dt
UniPhier ARM64 SoC DT updates for v4.16
- clean up gpios properties by macro
- add GPIO hog for PXs3 reference node
- add has-transaction-translator property to generic-ehci nodes
- enable more serial ports for PXs3 reference node
* tag 'uniphier-dt64-v4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier:
arm64: dts: uniphier: enable more serial ports for PXs3 ref board
arm64: dts: uniphier: add has-transaction-translator property to usb node for LD11
arm64: dts: uniphier: add GPIO hog definition for PXs3
arm64: dts: uniphier: use macros in dt-bindings header
Signed-off-by: Olof Johansson <olof@lixom.net>
There are two important changes in this round.
The first removes the redundant pinctrl setting for the MMC card detect
GPIO. We are moving to strict pinctrl/GPIO exclusion, i.e. GPIO usage
will block other pin muxing usage, and vice versa. The usage of pinmux
for guarding GPIO pins in the device tree prevents us from doing so.
This is part of an ongoing effort to clean up the existing device trees.
The other important change enables the PMIC on the Orangepi Win. The
PMIC provides power to most of the external onboard peripherals.
Enabling it will allow us to enable Ethernet or WiFi support later on.
The remaining changes in this round enable some peripheral, such as
Ethernet, an external WiFi chip, or LEDs.
-----BEGIN PGP SIGNATURE-----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=A9DZ
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt64-for-4.16' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Allwinner DT64 changes for 4.16
There are two important changes in this round.
The first removes the redundant pinctrl setting for the MMC card detect
GPIO. We are moving to strict pinctrl/GPIO exclusion, i.e. GPIO usage
will block other pin muxing usage, and vice versa. The usage of pinmux
for guarding GPIO pins in the device tree prevents us from doing so.
This is part of an ongoing effort to clean up the existing device trees.
The other important change enables the PMIC on the Orangepi Win. The
PMIC provides power to most of the external onboard peripherals.
Enabling it will allow us to enable Ethernet or WiFi support later on.
The remaining changes in this round enable some peripheral, such as
Ethernet, an external WiFi chip, or LEDs.
* tag 'sunxi-dt64-for-4.16' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: dts: allwinner: a64: bananapi-m64: Add LED device node
arm64: dts: a64-olinuxino: Enable RTL8723BS WiFi
arm64: dts: allwinner: h5: NanoPi NEO Plus2 : add EMAC support
arm64: dts: allwinner: H5: remove redundant MMC0 card detect pin
arm64: allwinner: a64: Enable AXP803 for Orangepi Win
arm64: dts: orange-pi-zero-plus2: enable AP6212a WiFi/BT combo
Signed-off-by: Olof Johansson <olof@lixom.net>
A random assortment of improvements.
GPIO device nodes are added for the AXP813/AXP818 PMICs, meaning we can
finally use the GPIO pins on the PMICs. The LDOs on the GPIO pins can
also be properly muxed and guarded.
EMAC Ethernet support is enabled for more H3 boards, and also for the
A83T, following the return of the bindings in 4.15, after a last minute
revert in 4.13. This will make the H3/A83T boards much more useful in
headless applications.
Two new boards are introduced. The Orange Pi R1 is a small board with
two Ethernet interfaces (one EMAC-based and one USB-based) and a WiFi
chip. This board is fully supported, with the exception of TV-out on
the expansion header, which will not be enabled by default. The WiFi
chip (RTL8189FTV) requires an out-of-tree driver. The Libre Computer
Board ALL-H3-CC H3 version is a newcomer to the Allwinner SBC space,
which was mostly represented by a bunch of fruit-Pis. It is mostly
supported, with the exception of HDMI and camera sensor interface,
which have not been implemented yet.
Two minor patches enable the audio codec on the A13 Olinuxino, and
HDMI output on the pcDuino3 Nano.
-----BEGIN PGP SIGNATURE-----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=UDxH
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-4.16' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Allwinner DT changes for 4.16
A random assortment of improvements.
GPIO device nodes are added for the AXP813/AXP818 PMICs, meaning we can
finally use the GPIO pins on the PMICs. The LDOs on the GPIO pins can
also be properly muxed and guarded.
EMAC Ethernet support is enabled for more H3 boards, and also for the
A83T, following the return of the bindings in 4.15, after a last minute
revert in 4.13. This will make the H3/A83T boards much more useful in
headless applications.
Two new boards are introduced. The Orange Pi R1 is a small board with
two Ethernet interfaces (one EMAC-based and one USB-based) and a WiFi
chip. This board is fully supported, with the exception of TV-out on
the expansion header, which will not be enabled by default. The WiFi
chip (RTL8189FTV) requires an out-of-tree driver. The Libre Computer
Board ALL-H3-CC H3 version is a newcomer to the Allwinner SBC space,
which was mostly represented by a bunch of fruit-Pis. It is mostly
supported, with the exception of HDMI and camera sensor interface,
which have not been implemented yet.
Two minor patches enable the audio codec on the A13 Olinuxino, and
HDMI output on the pcDuino3 Nano.
* tag 'sunxi-dt-for-4.16' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sun8i: h3: nanopi-m1-plus: fix missing ethernet 0 in aliases
ARM: dts: sun8i: h3: Enable dwmac-sun8i on the Nanopi M1
ARM: dts: sun7i: Enable HDMI on pcDuino3 Nano
ARM: dts: sun8i: a83t: Add I2C device nodes and pinmux settings
ARM: dts: sun8i: a83t: Add I2S controller device nodes
ARM: dts: sun8i-h3: Remove allwinner,leds-active-low for non internal PHY
ARM: dts: sun8i: a83t: Enable Ethernet on two boards
ARM: dts: sun8i: a83t: add dwmac-sun8i device node
ARM: dts: sun8i: h3: enable USB OTG for NanoPi Neo board
ARM: dts: sun8i: h3: Add dts file for Libre Computer Board ALL-H3-CC H3 ver.
ARM: dtsi: axp81x: set pinmux for GPIO0/1 when used as LDOs
ARM: dtsi: axp81x: add GPIO DT node
ARM: dts: sun8i: add support for Orange Pi R1
ARM: dts: sunxi: Add codec for A13 Olinuxino
Signed-off-by: Olof Johansson <olof@lixom.net>
- Enable GPIO bank2 for K2L
- Enable QSPI for K2G & K2G-EVM
- Enable UART1/2 for K2G & K2G-EVM
- Enable peripherals for K2G-ICE
- Fix C1 and C2 DTS warnings
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=rpPb
-----END PGP SIGNATURE-----
Merge tag 'keystone_dts_for_4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone into next/dt
ARM: Keystone DTS update for 4.16
- Enable GPIO bank2 for K2L
- Enable QSPI for K2G & K2G-EVM
- Enable UART1/2 for K2G & K2G-EVM
- Enable peripherals for K2G-ICE
- Fix C1 and C2 DTS warnings
* tag 'keystone_dts_for_4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
ARM: dts: keystone-k2l-clocks: Add missing unit name to clock nodes that have regs
ARM: dts: keystone-k2e-clocks: Add missing unit name to clock nodes that have regs
ARM: dts: keystone-hk-clocks: Add missing unit name to clock nodes that have regs
ARM: dts: keystone-clocks: Add missing unit name to clock nodes that have regs
ARM: dts: keystone: Add missing unit name to interrupt controller
ARM: dts: keystone: Get rid of usage of skeleton.dtsi
ARM: dts: keystone*: Use a single soc0 instance
ARM: dts: keystone*: Standardize license with SPDX tag
ARM: dts: k2g-evm: Enable UART 2
ARM: dts: k2g: Add UART 1 and 2 instances
ARM: dts: keystone: Add generic compatible string for I2C EEPROM
ARM: dts: keystone-k2g-ice: Add DT nodes for few peripherals
ARM: dts: keystone-k2g-evm: Add QSPI DT node.
ARM: dts: keystone-k2g: Move ti,non-removable property to board dts
ARM: dts: keystone-k2g-evm: Fix botched up merge
ARM: dts: keystone-k2g: Add QSPI DT entry
ARM: dts: keystone-k2l: Add the second gpio bank node
Signed-off-by: Olof Johansson <olof@lixom.net>
This branch mostly configures more hardware support:
- Clean-up dts files to remove leading 0x and 0s from binding notation
to remove more dtc compiler warnings
- A series of am437x updates for backlight, to fix inverted pad
pull macro, and to configure power management related OPPs
- Configure n950 and droid 4 command mode LCD panels
- Updates to pandora and gta04 LCD panels
- Add support for am574x-idk
- A series of changes to configure more dra7 related PCIe features
- A series of fixes for am335x-boneblue for WLAN, UARTs and CAN
configuration
- A series of changes to configure dra7 OPPs and VDD supplies
-----BEGIN PGP SIGNATURE-----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=G2ZQ
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.16/dt-pt2-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Second set of device tree changes for omaps for v4.16 merge window
This branch mostly configures more hardware support:
- Clean-up dts files to remove leading 0x and 0s from binding notation
to remove more dtc compiler warnings
- A series of am437x updates for backlight, to fix inverted pad
pull macro, and to configure power management related OPPs
- Configure n950 and droid 4 command mode LCD panels
- Updates to pandora and gta04 LCD panels
- Add support for am574x-idk
- A series of changes to configure more dra7 related PCIe features
- A series of fixes for am335x-boneblue for WLAN, UARTs and CAN
configuration
- A series of changes to configure dra7 OPPs and VDD supplies
* tag 'omap-for-v4.16/dt-pt2-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (29 commits)
Revert "ARM: dts: dra7: Add properties to enable PCIe x2 lane mode"
ARM: dts: am572x-idk: Add cpu0 vdd supply
ARM: dts: am571x-idk: Add cpu0 vdd supply
ARM: dts: dra72-evm-tps65917: Add cpu0 vdd supply
ARM: dts: dra7-evm: Add cpu0 vdd supply
ARM: dts: am57xx-beagle-x15-common: Add cpu0 vdd supply
ARM: dts: dra7: Enable 1.5 GHz operation for the CPU
ARM: dts: dra7: Add MPU OPP supply node
ARM: dts: dra7: Add vbb-supply to cpu and additional voltages
ARM: dts: am335x-boneblue: enable can
ARM: dts: am335x-boneblue: enable usarts
ARM: dts: am335x-boneblue: fix wl1835 IRQ pin
ARM: dts: dra7: Remove deprecated PCI compatible string
ARM: dts: dra76-evm: Enable x2 PCIe lanes
ARM: dts: DRA72x: Use PCIe compatible specific to dra72
ARM: dts: DRA74x: Use PCIe compatible specific to dra74
ARM: dts: dra7: Add properties to enable PCIe x2 lane mode
ARM: dts: am57xx: Add support for am574x-idk
ARM: dts: am43x-epos-evm: Hook dcdc2 as the cpu0-supply
ARM: dts: am437x-idk-evm: Disable OPP50 for MPU
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Add the NAND support on the Marvell 8040-DB board
Add the thermal support for Martvell A7K/A8K Socs
Add nodes allowing cpufreq support on Aramda 3700 SoCs
-----BEGIN PGP SIGNATURE-----
iIEEABECAEEWIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCWjzjGiMcZ3JlZ29yeS5j
bGVtZW50QGZyZWUtZWxlY3Ryb25zLmNvbQAKCRALBhiOFHI71eRxAKCkcg3nYB1F
MLYZ5pQg0SA8p8IOPwCfczw9Uui9xxSaMnEjBgcDOZnkoSo=
=9aGc
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt64-4.16-1' of git://git.infradead.org/linux-mvebu into next/dt
mvebu dt64 for 4.16 (part 1)
Add the NAND support on the Marvell 8040-DB board
Add the thermal support for Martvell A7K/A8K Socs
Add nodes allowing cpufreq support on Aramda 3700 SoCs
* tag 'mvebu-dt64-4.16-1' of git://git.infradead.org/linux-mvebu:
ARM64: dts: marvell: Add thermal support for A7K/A8K
arm64: dts: marvell: armada-37xx: add nodes allowing cpufreq support
arm64: dts: marvell: add NAND support on the 8040-DB board
Signed-off-by: Olof Johansson <olof@lixom.net>
Fix potential dtc warnings on kirkwoods files
Declare a new pin (RB) usbale for NAND controller on Armada 38x
-----BEGIN PGP SIGNATURE-----
iIEEABECAEEWIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCWjzh4yMcZ3JlZ29yeS5j
bGVtZW50QGZyZWUtZWxlY3Ryb25zLmNvbQAKCRALBhiOFHI71c6eAKCJWCDib+4j
So2W8yQbI+glOCfjQACfaFGVosbxIilV4+l1bUZJFXHTSSk=
=uIda
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt-4.16-1' of git://git.infradead.org/linux-mvebu into next/dt
mvebu dt for 4.16 (part 1)
Fix potential dtc warnings on kirkwoods files
Declare a new pin (RB) usbale for NAND controller on Armada 38x
* tag 'mvebu-dt-4.16-1' of git://git.infradead.org/linux-mvebu:
arm: kirkwood: dts: Use lower case for bindings notation
ARM: dts: armada-38x: Add NAND RB pinctrl information
Signed-off-by: Olof Johansson <olof@lixom.net>
* r8a7745 (RZ/G1E) SoC
- Enable SMP
Fabrizio Castro says "Add DT node for the Advanced Power Management
Unit (APMU), add the second CPU core, and use "renesas,apmu" as
"enable-method"."
* r8a7743 (RZ/G1M) SoC
- Add node for thermal sensor module with thermal-zone support
* r8a7743 (RZ/G1M) and r8a7745 (RZ/G1E) SoCs
- Add:
+ Renesas Core Match Timer (CMT) support
+ Renesas Timer Pulse Unit PWM Controller (TPU) support
+ Renesas PWM Timer Controller (PWM) support
* r8a7743 (RZ/G1M) iW-RainboW-G20D-Qseven and
r8a7745 (RZ/G1E) iW-RainboW-G22D development platforms
- Add sound support
* r8a7743 (RZ/G1M), r8a7745 (RZ/G1E) and r8a7792 (R-Car V2H) SoCs
- Allow DTBs of boards of these SoCs to build without any warnings when
compiled with W=1 using gcc-linaro-5.4.1-2017.05
+ Move nodes which have no reg property out of bus, they don't belong there
+ Also sort sub-nodes of root node to allow for easier maintenance
* r8a7790 (R-Car H2), r8a7791 (R-Car M2-W) and r8a7793 (R-Car M2-N) SoCs
- Correct critical CPU temperature
Chris Paterson says "The current R-Car Gen2 device trees define the CPU
critical temperature as 115°C.
The R-Car hardware manuals state that Tc = –40°C to +105°C. The thermal
sensor has an accuracy of ±5°C and there can be a temperature
difference of 1 or 2 degrees between Tjmax and the thermal sensor due
to the location of the latter.
This means that 95°C is a safer value to use.
This value should also apply to r8a7792 but thermal sensor support has
not been added yet."
* r8a7740 (R-Mobile A1) SoC
- Correct TPU register block size
Geert Uytterhoven says "The Timer Pulse Unit has registers that lie
outside the declared register block. Enlarge the register block size to
fix this.
This was probably based on the old platform code, which also assumed a
register block size of 0x100."
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEE4nzZofWswv9L/nKF189kaWo3T74FAlo83NsACgkQ189kaWo3
T75/Ug/+K0JFjXfzVGLLhQ0GYV+nJLD2Rz5J0WOISZSKQ2MMuIDNPYa/r2edOzkV
qp75Fjp0FE0XvYQQwPsKSY8Nt0CRg1j/wYw9wMvJZ1lJUgeL9DuLhzqZ2mlvv0v9
gLaZau011QpKv3k/MoOVEPOUrKBSqhBJaTZ3ufv/tYvpI/if//8jRafdkLPzSPcQ
IktmihGIiB2uJeCwZsEfhn3kWvjc4PegVbL6jkTrHd21oDA7KYnCLP7XBi3eut1C
smVzcN+NofAIDgk7x+R6XdEl6bJejUEox/ixk/HgJ2yjD2bsI8ILL6Mx2BKREg6x
oYJlmXo6/XNep+9H45JaTCgRJfzhfFQu15PAYE8qROeGcoFm7tnGLXYe0zEaXy9G
K22dkZog+uLpwCeHpXYsXFDknhQPds3a/nd4crpVlmsnfuhdLYwAn4IxWnBBl/SV
u9xHegfrexqT8pE44JDA+cWqGQz2gss33pBejJqB+3HEijg/CQ43eZbQVEYpMx01
a/9mQqJvk3IyC6EyzxMWfq9k8e0rcq6APRu+dd2oPyUTVNKgWuQXHHyyzIlzn55w
NvbUf5W6wyxa/kA2l8XeBHToKAn1pBbhEakIF1tGYKB1a8AfHbuHXeuXLFLNmQDN
3ON16LEEzqBlHjn2kxHG/gbFUTHXDl1gwBPo92CATuHe+P8TG+Q=
=2oL+
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt2-for-v4.16' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Second Round of Renesas ARM Based SoC DT Updates for v4.16
* r8a7745 (RZ/G1E) SoC
- Enable SMP
Fabrizio Castro says "Add DT node for the Advanced Power Management
Unit (APMU), add the second CPU core, and use "renesas,apmu" as
"enable-method"."
* r8a7743 (RZ/G1M) SoC
- Add node for thermal sensor module with thermal-zone support
* r8a7743 (RZ/G1M) and r8a7745 (RZ/G1E) SoCs
- Add:
+ Renesas Core Match Timer (CMT) support
+ Renesas Timer Pulse Unit PWM Controller (TPU) support
+ Renesas PWM Timer Controller (PWM) support
* r8a7743 (RZ/G1M) iW-RainboW-G20D-Qseven and
r8a7745 (RZ/G1E) iW-RainboW-G22D development platforms
- Add sound support
* r8a7743 (RZ/G1M), r8a7745 (RZ/G1E) and r8a7792 (R-Car V2H) SoCs
- Allow DTBs of boards of these SoCs to build without any warnings when
compiled with W=1 using gcc-linaro-5.4.1-2017.05
+ Move nodes which have no reg property out of bus, they don't belong there
+ Also sort sub-nodes of root node to allow for easier maintenance
* r8a7790 (R-Car H2), r8a7791 (R-Car M2-W) and r8a7793 (R-Car M2-N) SoCs
- Correct critical CPU temperature
Chris Paterson says "The current R-Car Gen2 device trees define the CPU
critical temperature as 115°C.
The R-Car hardware manuals state that Tc = –40°C to +105°C. The thermal
sensor has an accuracy of ±5°C and there can be a temperature
difference of 1 or 2 degrees between Tjmax and the thermal sensor due
to the location of the latter.
This means that 95°C is a safer value to use.
This value should also apply to r8a7792 but thermal sensor support has
not been added yet."
* r8a7740 (R-Mobile A1) SoC
- Correct TPU register block size
Geert Uytterhoven says "The Timer Pulse Unit has registers that lie
outside the declared register block. Enlarge the register block size to
fix this.
This was probably based on the old platform code, which also assumed a
register block size of 0x100."
* tag 'renesas-dt2-for-v4.16' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (37 commits)
ARM: dts: r8a7745: Add missing clock for secondary CA7 CPU core
ARM: dts: iwg22d-sodimm: Sound DMA support via DVC on DTS
ARM: dts: iwg22d-sodimm: Sound DMA support via SRC on DTS
ARM: dts: iwg22d-sodimm: Sound DMA support via BUSIF on DTS
ARM: dts: iwg22d-sodimm: Sound DMA support on DTS
ARM: dts: iwg22d-sodimm: Sound PIO support
ARM: dts: iwg22d-sodimm: Enable SGTL5000 audio codec
ARM: dts: r8a7745: Add sound support
ARM: dts: r8a7745: Add audio DMAC support
ARM: dts: r8a7745: Add audio clocks
ARM: dts: r8a7740: Correct TPU register block size
ARM: dts: r8a7743: move timer and thermal-zones nodes out of bus
ARM: dts: r8a7743: sort root sub-nodes alphabetically
ARM: dts: iwg20d-q7-common: Sound DMA support via DVC on DTS
ARM: dts: iwg20d-q7-common: Sound DMA support via SRC on DTS
ARM: dts: iwg20d-q7-common: Sound DMA support via BUSIF on DTS
ARM: dts: iwg20d-q7-common: Sound DMA support on DTS
ARM: dts: iwg20d-q7-common: Sound PIO support
ARM: dts: iwg20d-q7-common: Enable SGTL5000 audio codec
ARM: dts: r8a7792: move timer node out of bus
...
Signed-off-by: Olof Johansson <olof@lixom.net>
* Add usb3_phy node to r8a7795 (R-Car H3) and r8a7796 (R-Car M3-W) SoCs, and
enable usb3_peri0 on salvator boards
* Allow DTBs of boards of r8a7795 (R-Car H3) and r8a7796 SoCs to build
without any warnings when compiled with W=1 using gcc-linaro-5.4.1-2017.05
- Move nodes which have no reg property out of bus, they don't belong there
- Add reg properties to dummy pciec[01] nodes
- Also sort sub-nodes of root node to allow for easier maintenance
* Add Add EthernetAVB PHY reset to r8a7795 (R-Car H3) and r8a7796 SoCs boards.
Geert Uytterhoeven says "... add properties to describe the EthernetAVB
PHY reset topology to the common Salvator-X/XS and ULCB DTS files, which
solves two issues:
1. On Salvator-XS, the enable pin of the regulator providing PHY power
is connected to PRESETn, and PSCI powers down the SoC during system
suspend. Hence a PHY reset is needed to restore network
functionality after system resume.
2. Linux should not rely on the boot loader having reset the PHY, but
should reset the PHY during driver probe."
-----BEGIN PGP SIGNATURE-----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=L57U
-----END PGP SIGNATURE-----
Merge tag 'renesas-arm64-dt2-for-v4.16' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Second Round of Renesas ARM64 Based SoC DT Updates for v4.16
* Add usb3_phy node to r8a7795 (R-Car H3) and r8a7796 (R-Car M3-W) SoCs, and
enable usb3_peri0 on salvator boards
* Allow DTBs of boards of r8a7795 (R-Car H3) and r8a7796 SoCs to build
without any warnings when compiled with W=1 using gcc-linaro-5.4.1-2017.05
- Move nodes which have no reg property out of bus, they don't belong there
- Add reg properties to dummy pciec[01] nodes
- Also sort sub-nodes of root node to allow for easier maintenance
* Add Add EthernetAVB PHY reset to r8a7795 (R-Car H3) and r8a7796 SoCs boards.
Geert Uytterhoeven says "... add properties to describe the EthernetAVB
PHY reset topology to the common Salvator-X/XS and ULCB DTS files, which
solves two issues:
1. On Salvator-XS, the enable pin of the regulator providing PHY power
is connected to PRESETn, and PSCI powers down the SoC during system
suspend. Hence a PHY reset is needed to restore network
functionality after system resume.
2. Linux should not rely on the boot loader having reset the PHY, but
should reset the PHY during driver probe."
* tag 'renesas-arm64-dt2-for-v4.16' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
arm64: dts: renesas: salvator-common: enable usb3_peri0
arm64: dts: renesas: salvator-common: enable usb3_phy0 node
arm64: dts: renesas: r8a7796: add usb3_phy node
arm64: dts: renesas: r8a7795: add usb3_phy node
arm64: dts: renesas: r8a7796: add reg properties to pciec[01] nodes
arm64: dts: renesas: r8a7796: move nodes which have no reg property out of bus
arm64: dts: renesas: r8a7796: sort subnodes of root node alphabetically
arm64: dts: renesas: r8a7795: sort subnodes of root node alphabetically
arm64: dts: renesas: ulcb: Add EthernetAVB PHY reset
arm64: dts: renesas: salvator-common: Add EthernetAVB PHY reset
arm64: dts: renesas: r8a7795: Move nodes which have no reg property out of bus
Signed-off-by: Olof Johansson <olof@lixom.net>
