Seville does not need to depend on PCI or on the ENETC MDIO controller.
There will also be other compile-time differences in the future.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not only does Sevile not have a PTP clock, but with separate modules,
this structure cannot even live in felix.c, due to the .owner =
THIS_MODULE assignment causing this link time error:
drivers/net/dsa/ocelot/felix.o:(.data+0x0): undefined reference to `__this_module'
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While we don't plan on making any changes to this function, currently
this is the only remaining dependency between felix and seville, after
the PCS has been refactored out into pcs-lynx.c.
Duplicate this function in seville to break the dependency completely.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Over the time, some patches have introduced structures aligned with
spaces, near structures aligned with tabs. Fix the inconsistencies.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reindent these definitions to be in line with the rest of the driver.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some definitions were likely copied from
drivers/net/mdio/mdio-mscc-miim.c.
They are not necessary, remove them.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The overall idea (issue soft reset, enable memories, initialize
memories, enable core) is the same, so it would make sense that an
attempt is made to unify the procedures.
It is not immediately obvious that the fields are not part of the same
register targets, though. So add a comment.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As per documentation, proper startup sequence is:
* Enable memories
* Initialize memories
* Enable core
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is another one of these right above the readx_poll_status.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since these helpers for regmap fields are available, use them.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We got slightly different patches removing a double word
in a comment in net/ipv4/raw.c - picked the version from net.
Simple conflict in drivers/net/ethernet/ibm/ibmvnic.c. Use cached
values instead of VNIC login response buffer (following what
commit 507ebe6444 ("ibmvnic: Fix use-after-free of VNIC login
response buffer") did).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use the helper functions introduced by the newly added
Lynx PCS MDIO module in the Felix VSC9959 and Seville VSC9953.
Instead of representing the PCS as a phy_device, a mdio_device structure
will be passed to the Lynx module which is now actually implementing all
the PCS configuration and status reporting.
All code previously used for PCS monitoring and runtime configuration
is removed and replaced will calls to the Lynx PCS operations.
Tested on the following SERDES protocols of LS1028A: 0x7777
(2500Base-X), 0x85bb (QSGMII), 0x9999 (SGMII) and 0x13bb (USXGMII).
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Every iteration of for_each_available_child_of_node() decrements
the reference count of the previous node, however when control
is transferred from the middle of the loop, as in the case of
a return or break or goto, there is no decrement thus ultimately
resulting in a memory leak.
Fix a potential memory leak in felix.c by inserting of_node_put()
before the return statement.
Issue found with Coccinelle.
Signed-off-by: Sumera Priyadarsini <sylphrenadin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Kconfig help text contains the phrase "the the" in the help
text. Fix this.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that there are USXGMII constants available, drop the old definitions
and reuse the generic ones.
Signed-off-by: Michael Walle <michael@walle.cc>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Having the users of MSCC_OCELOT_SWITCH_LIB depend on REGMAP_MMIO was a
bad idea, since that symbol is not user-selectable. So we should have
kept a 'select REGMAP_MMIO'.
When we do that, we run into 2 more problems:
- By depending on GENERIC_PHY, we are causing a recursive dependency.
But it looks like GENERIC_PHY has no other dependencies, and other
drivers select it, so we can select it too:
drivers/of/Kconfig:69:error: recursive dependency detected!
drivers/of/Kconfig:69: symbol OF_IRQ depends on IRQ_DOMAIN
kernel/irq/Kconfig:68: symbol IRQ_DOMAIN is selected by REGMAP
drivers/base/regmap/Kconfig:7: symbol REGMAP default is visible depending on REGMAP_MMIO
drivers/base/regmap/Kconfig:39: symbol REGMAP_MMIO is selected by MSCC_OCELOT_SWITCH_LIB
drivers/net/ethernet/mscc/Kconfig:15: symbol MSCC_OCELOT_SWITCH_LIB is selected by MSCC_OCELOT_SWITCH
drivers/net/ethernet/mscc/Kconfig:22: symbol MSCC_OCELOT_SWITCH depends on GENERIC_PHY
drivers/phy/Kconfig:8: symbol GENERIC_PHY is selected by PHY_BCM_NS_USB3
drivers/phy/broadcom/Kconfig:41: symbol PHY_BCM_NS_USB3 depends on MDIO_BUS
drivers/net/phy/Kconfig:13: symbol MDIO_BUS depends on MDIO_DEVICE
drivers/net/phy/Kconfig:6: symbol MDIO_DEVICE is selected by PHYLIB
drivers/net/phy/Kconfig:254: symbol PHYLIB is selected by ARC_EMAC_CORE
drivers/net/ethernet/arc/Kconfig:19: symbol ARC_EMAC_CORE is selected by ARC_EMAC
drivers/net/ethernet/arc/Kconfig:25: symbol ARC_EMAC depends on OF_IRQ
- By depending on PHYLIB, we are causing a recursive dependency. PHYLIB
only has a single dependency, "depends on NETDEVICES", which we are
already depending on, so we can again hack our way into conformance by
turning the PHYLIB dependency into a select.
drivers/of/Kconfig:69:error: recursive dependency detected!
drivers/of/Kconfig:69: symbol OF_IRQ depends on IRQ_DOMAIN
kernel/irq/Kconfig:68: symbol IRQ_DOMAIN is selected by REGMAP
drivers/base/regmap/Kconfig:7: symbol REGMAP default is visible depending on REGMAP_MMIO
drivers/base/regmap/Kconfig:39: symbol REGMAP_MMIO is selected by MSCC_OCELOT_SWITCH_LIB
drivers/net/ethernet/mscc/Kconfig:15: symbol MSCC_OCELOT_SWITCH_LIB is selected by MSCC_OCELOT_SWITCH
drivers/net/ethernet/mscc/Kconfig:22: symbol MSCC_OCELOT_SWITCH depends on PHYLIB
drivers/net/phy/Kconfig:254: symbol PHYLIB is selected by ARC_EMAC_CORE
drivers/net/ethernet/arc/Kconfig:19: symbol ARC_EMAC_CORE is selected by ARC_EMAC
drivers/net/ethernet/arc/Kconfig:25: symbol ARC_EMAC depends on OF_IRQ
Fixes: f4d0323bae ("net: mscc: ocelot: convert MSCC_OCELOT_SWITCH into a library")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This is another switch from Vitesse / Microsemi / Microchip, that has
10 ports (8 external, 2 internal) and is integrated into the Freescale /
NXP T1040 PowerPC SoC. It is very similar to Felix from NXP LS1028A,
except that this is a platform device and Felix is a PCI device, and it
doesn't support IEEE 1588 and TSN.
Like Felix, this driver configures its own PCS on the internal MDIO bus
using a phy_device abstraction for it (yes, it will be refactored to use
a raw mdio_device, like other phylink drivers do, but let's keep it like
that for now). But unlike Felix, the MDIO bus and the PCS are not from
the same vendor. The PCS is the same QorIQ/Layerscape PCS as found in
Felix/ENETC/DPAA*, but the internal MDIO bus that is used to access it
is actually an instantiation of drivers/net/phy/mdio-mscc-miim.c. But it
would be difficult to reuse that driver (it doesn't even use regmap, and
it's less than 200 lines of code), so we hand-roll here some internal
MDIO bus accessors within seville_vsc9953.c, which serves the purpose of
driving the PCS absolutely fine.
Also, same as Felix, the PCS doesn't support dynamic reconfiguration of
SerDes protocol, so we need to do pre-validation of PHY mode from device
tree and not let phylink change it.
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Felix is not actually meant to be a DSA driver only for the switch
inside NXP LS1028A, but an umbrella for all Vitesse / Microsemi /
Microchip switches that are register-compatible with Ocelot and that are
using in DSA mode (with an NPI Ethernet port).
For the dsa_switch_ops exported by the felix driver to be generic enough
to be used by other non-PCI switches, we need to move the PCI-specific
probing to the low-level translation module felix_vsc9959.c. This way,
other switches can have their own probing functions, as platform devices
or otherwise.
This patch also removes the "Felix instance table", which did not stand
the test of time and is unnecessary at this point.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ocelot_wm_encode function deals with setting thresholds for pause
frame start and stop. In Ocelot and Felix the register layout is the
same, but for Seville, it isn't. The easiest way to accommodate Seville
hardware configuration is to introduce a function pointer for setting
this up.
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Seville has a different bitwise layout than Ocelot and Felix.
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this patch we try to kill 2 birds with 1 stone.
First of all, some switches that use tag_ocelot.c don't have the exact
same bitfield layout for the DSA tags. The destination ports field is
different for Seville VSC9953 for example. So the choices are to either
duplicate tag_ocelot.c into a new tag_seville.c (sub-optimal) or somehow
take into account a supposed ocelot->dest_ports_offset when packing this
field into the DSA injection header (again not ideal).
Secondly, tag_ocelot.c already needs to memset a 128-bit area to zero
and call some packing() functions of dubious performance in the
fastpath. And most of the values it needs to pack are pretty much
constant (BYPASS=1, SRC_PORT=CPU, DEST=port index). So it would be good
if we could improve that.
The proposed solution is to allocate a memory area per port at probe
time, initialize that with the statically defined bits as per chip
hardware revision, and just perform a simpler memcpy in the fastpath.
Other alternatives have been analyzed, such as:
- Create a separate tag_seville.c: too much code duplication for just 1
bit field difference.
- Create a separate DSA_TAG_PROTO_SEVILLE under tag_ocelot.c, just like
tag_brcm.c, which would have a separate .xmit function. Again, too
much code duplication for just 1 bit field difference.
- Allocate the template from the init function of the tag_ocelot.c
module, instead of from the driver: couldn't figure out a method of
accessing the correct port template corresponding to the correct
tagger in the .xmit function.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently Felix and Ocelot share the same bit layout in these per-port
registers, but Seville does not. So we need reg_fields for that.
Actually since these are per-port registers, we need to also specify the
number of ports, and register size per port, and use the regmap API for
multiple ports.
There's a more subtle point to be made about the other 2 register
fields:
- QSYS_SWITCH_PORT_MODE_SCH_NEXT_CFG
- QSYS_SWITCH_PORT_MODE_INGRESS_DROP_MODE
which we are not writing any longer, for 2 reasons:
- Using the previous API (ocelot_write_rix), we were only writing 1 for
Felix and Ocelot, which was their hardware-default value, and which
there wasn't any intention in changing.
- In the case of SCH_NEXT_CFG, in fact Seville does not have this
register field at all, and therefore, if we want to have common code
we would be required to not write to it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the register definitions for the MSCC MIIM MDIO controller in
preparation for seville_vsc9959.c to create its accessors for the
internal MDIO bus.
Since we've introduced elements to ocelot_regfields that are not
instantiated by felix and ocelot, we need to define the size of the
regfields arrays explicitly, otherwise ocelot_regfields_init, which
iterates up to REGFIELD_MAX, will fault on the undefined regfield
entries (if we're lucky).
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At the moment, there are some minimal register differences between
VSC7514 Ocelot and VSC9959 Felix. To be precise, the PCS1G registers are
missing from Felix because it was integrated with an NXP PCS.
But with VSC9953 Seville (not yet introduced), the register differences
are more pronounced. The MAC registers are located at different offsets
within the DEV_GMII target. So we need to refactor the driver to keep a
regmap even for per-port registers. The callers of the ocelot_port_readl
and ocelot_port_writel were kept unchanged, only the implementation is
now more generic.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Phylink now requires that parameters established through
auto-negotiation be written into the MAC at the time of the
mac_link_up() callback. In the case of felix, that means taking the port
out of reset, setting the correct timers for PAUSE frames, and
enabling/disabling TX flow control.
This patch also splits the inband and noinband configuration of the
vsc9959 PCS (currently found in a function called "init") into 2
different functions, which have a nomenclature closer to phylink:
"config", for inband setup, and "link_up", for noinband (forced) setup.
This is necessary as a preparation step for giving up control of the PCS
to phylink, which will be done in further patch series.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Phylink uses the .mac_an_restart method to offer the user an
implementation of the "ethtool -r" behavior, when the media-side auto
negotiation can be restarted by the local MAC PCS. This is the case for
fiber modes 1000Base-X and 2500Base-X (IEEE clause 37) that don't have
an Ethernet PHY connected locally, and the media is connected to the MAC
PCS directly.
On the other hand, the Cisco SGMII and USXGMII standards also have an
auto negotiation mechanism based on IEEE 802.3 clause 37 (their
respective specs require a MAC PCS and a PHY PCS to implement the same
state machine, which is described in IEEE 802.3 "Auto-Negotiation Figure
37-6"), so the ability to restart auto-negotiation is intrinsically
symmetrical (the MAC PCS can do it too).
However, it appears that not all SGMII/USXGMII PHYs have logic to
restart the MDI-side auto-negotiation process when they detect a
transition of the SGMII link from data mode to configuration mode.
Some do (VSC8234) and some don't (AR8033, MV88E1111). IEEE and/or Cisco
specification wordings to not help to prove whether propagating the "AN
restart" event from MII side ("mr_restart_an") to MDI side
("mr_restart_negotiation") is required behavior - neither of them
specifies any mandatory interaction between the clause 37 AN state
machine from Figure 37-6 and the clause 28 AN state machine from Figure
28-18.
Therefore, even if a certain behavior could be proven as being required,
real-life SGMII/USXGMII PHYs are inconsistent enough that a clause 37 AN
restart cannot be used by phylink to reliably trigger a media-side
renegotiation, when the user requests it via ethtool.
The only remaining use that the .mac_an_restart callback might possibly
have, given what we know now, is to implement some silicon quirks, but
so far that has proven to not be necessary.
So remove this code for now, since it never gets called and we don't
foresee any circumstance in which it might be, either.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
state->speed holds a value of 10, 100, 1000 or 2500, but
SYS_MAC_FC_CFG_FC_LINK_SPEED expects a value in the range 0, 1, 2 or 3.
So set the correct speed encoding into this register.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In VSC9959, the PCS is the one who performs rate adaptation (symbol
duplication) to the speed negotiated by the PHY. The MAC is unaware of
that and must remain configured for gigabit. If it is configured at
OCELOT_SPEED_10 or OCELOT_SPEED_100, it'll start transmitting PAUSE
frames out of control and never recover, _even if_ we then reconfigure
it at OCELOT_SPEED_1000 afterwards.
This patch fixes a bug that luckily did not have any functional impact.
We were writing 10, 100, 1000 etc into this 2-bit field in
DEV_CLOCK_CFG, but the hardware expects values in the range 0, 1, 2, 3.
So all speed values were getting truncated to 0, which is
OCELOT_SPEED_2500, and which also appears to be fine.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ping tested:
[ 11.808455] mscc_felix 0000:00:00.5 swp0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 11.816497] IPv6: ADDRCONF(NETDEV_CHANGE): swp0: link becomes ready
[root@LS1028ARDB ~] # ethtool -s swp0 advertise 0x4
[ 18.844591] mscc_felix 0000:00:00.5 swp0: Link is Down
[ 22.048337] mscc_felix 0000:00:00.5 swp0: Link is Up - 100Mbps/Half - flow control off
[root@LS1028ARDB ~] # ip addr add 192.168.1.1/24 dev swp0
[root@LS1028ARDB ~] # ping 192.168.1.2
PING 192.168.1.2 (192.168.1.2): 56 data bytes
(...)
^C--- 192.168.1.2 ping statistics ---
3 packets transmitted, 3 packets received, 0% packet loss
round-trip min/avg/max = 0.383/0.611/1.051 ms
[root@LS1028ARDB ~] # ethtool -s swp0 advertise 0x10
[ 355.637747] mscc_felix 0000:00:00.5 swp0: Link is Down
[ 358.788034] mscc_felix 0000:00:00.5 swp0: Link is Up - 1Gbps/Half - flow control off
[root@LS1028ARDB ~] # ping 192.168.1.2
PING 192.168.1.2 (192.168.1.2): 56 data bytes
(...)
^C
--- 192.168.1.2 ping statistics ---
16 packets transmitted, 16 packets received, 0% packet loss
round-trip min/avg/max = 0.301/0.384/1.138 ms
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver appears to write to BMCR_SPEED and BMCR_DUPLEX, fields which
are read-only, since they are actually configured through the
vendor-specific IF_MODE (0x14) register.
But the reason we're writing back the read-only values of MII_BMCR is to
alter these writable fields:
BMCR_RESET
BMCR_LOOPBACK
BMCR_ANENABLE
BMCR_PDOWN
BMCR_ISOLATE
BMCR_ANRESTART
In particular, the only field which is really relevant to this driver is
BMCR_ANENABLE. Clarify that intention by spelling it out, using
phy_set_bits and phy_clear_bits.
The driver also made a few writes to BMCR_RESET and BMCR_ANRESTART which
are unnecessary and may temporarily disrupt the link to the PHY. Remove
them.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since 'tcfp_burst' with TICK factor, driver side always need to recover
it to the original value, this patch moves the generic calculation and
recover to the 'burst' original value before offloading to device driver.
Signed-off-by: Po Liu <po.liu@nxp.com>
Acked-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the mdb hooks in felix and exports the mdb functions from
ocelot.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hide the CONFIG_MSCC_OCELOT_SWITCH option from users. It is meant to be
only a hardware library which is selected by the drivers that use it
(ocelot, felix).
Since it is "selected" from Kconfig, all its dependencies are manually
transferred to the driver that selects it. This is because "select" in
Kconfig language is a bit of a mess, and doesn't handle dependencies of
selected options quite right.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
xdp_umem.c had overlapping changes between the 64-bit math fix
for the calculation of npgs and the removal of the zerocopy
memory type which got rid of the chunk_size_nohdr member.
The mlx5 Kconfig conflict is a case where we just take the
net-next copy of the Kconfig entry dependency as it takes on
the ESWITCH dependency by one level of indirection which is
what the 'net' conflicting change is trying to ensure.
Signed-off-by: David S. Miller <davem@davemloft.net>
As explained in other commits before (b9cd75e668 and 87b0f983f6),
ocelot switches have a single egress-untagged VLAN per port, and the
driver would deny adding a second one while an egress-untagged VLAN
already exists.
But on the CPU port (where the VLAN configuration is implicit, because
there is no net device for the bridge to control), the DSA core attempts
to add a VLAN using the same flags as were used for the front-panel
port. This would make adding any untagged VLAN fail due to the CPU port
rejecting the configuration:
bridge vlan add dev swp0 vid 100 pvid untagged
[ 1865.854253] mscc_felix 0000:00:00.5: Port already has a native VLAN: 1
[ 1865.860824] mscc_felix 0000:00:00.5: Failed to add VLAN 100 to port 5: -16
(note that port 5 is the CPU port and not the front-panel swp0).
So this hardware will send all VLANs as tagged towards the CPU.
Fixes: 5605194877 ("net: dsa: ocelot: add driver for Felix switch family")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ocelot core library is written with the idea in mind that the VLAN
table is populated by the bridge. Otherwise, not even a sane default
pvid is provided: in standalone mode, the default pvid is 0, and the
core expects the bridge layer to change it to 1.
So without this patch, the VLAN table is completely empty at the end of
the commands below, and traffic is broken as a result:
ip link add dev br0 type bridge vlan_filtering 0 && ip link set dev br0 up
for eth in $(ls /sys/bus/pci/devices/0000\:00\:00.5/net/); do
ip link set dev $eth master br0
ip link set dev $eth up
done
ip link set dev br0 type bridge vlan_filtering 1
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MSCC bug fix in 'net' had to be slightly adjusted because the
register accesses are done slightly differently in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
The caller of devm_ioremap_resource(), either accidentally
or by wrong assumption, is writing back derived resource data
to global static resource initialization tables that should
have been constant. Meaning that after it computes the final
physical start address it saves the address for no reason
in the static tables. This doesn't affect the first driver
probing after reboot, but it breaks consecutive driver reloads
(i.e. driver unbind & bind) because the initialization tables
no longer have the correct initial values. So the next probe()
will map the device registers to wrong physical addresses,
causing ARM SError async exceptions.
This patch fixes all of the above.
Fixes: 5605194877 ("net: dsa: ocelot: add driver for Felix switch family")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently burst is clamping on rate and not burst, the assignment
of burst from the clamping discards the previous assignment of burst.
This looks like a cut-n-paste error from the previous clamping
calculation on ramp. Fix this by replacing ramp with burst.
Addresses-Coverity: ("Unused value")
Fixes: 0fbabf875d ("net: dsa: felix: add support Credit Based Shaper(CBS) for hardware offload")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VSC9959 hardware support the Credit Based Shaper(CBS) which part
of the IEEE-802.1Qav. This patch support sch_cbs set for VSC9959.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ocelot VSC9959 switch supports time-based egress shaping in hardware
according to IEEE 802.1Qbv. This patch add support for TAS configuration
on egress port of VSC9959 switch.
Felix driver is an instance of Ocelot family, with a DSA front-end. The
patch uses tc taprio hardware offload to setup TAS set function on felix
driver.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the default QoS Classification based on PCP and DEI of vlan tag,
after that, frames can be Classified to different Qos based on PCP tag.
If there is no vlan tag or vlan ignored, use port default Qos.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When running 'bridge fdb dump' on Felix, sometimes learnt and static MAC
addresses would appear, sometimes they wouldn't.
Turns out, the MAC table has 4096 entries on VSC7514 (Ocelot) and 8192
entries on VSC9959 (Felix), so the existing code from the Ocelot common
library only dumped half of Felix's MAC table. They are both organized
as a 4-way set-associative TCAM, so we just need a single variable
indicating the correct number of rows.
Fixes: 5605194877 ("net: dsa: ocelot: add driver for Felix switch family")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If there is no specific configuration of the felix switch in the device
tree, but only the default configuration (ie. given by the SoCs dtsi
file), the probe fails because no CPU port has been set. On the other
hand you cannot set a default CPU port because that depends on the
actual board using the switch.
[ 2.701300] DSA: tree 0 has no CPU port
[ 2.705167] mscc_felix 0000:00:00.5: Failed to register DSA switch: -22
[ 2.711844] mscc_felix: probe of 0000:00:00.5 failed with error -22
Thus let the device tree disable this device entirely, like it is also
done with the enetc driver of the same SoC.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Right now it can be seen that the VSC9959 (Felix) switch will not flood
frames if they have a VLAN tag with a PCP of 1-7 (nonzero).
It turns out that Felix is quite different from its cousin, Ocelot, in
that frame flooding can be allowed/denied per traffic class. Where
Ocelot has 1 instance of the ANA_FLOODING register, Felix has 8.
The approach that this driver is going to take is "thanks, but no
thanks". We have no use case of limiting the flooding domain based on
traffic class, so we just want to allow packets to be flooded, no matter
what traffic class they have.
So we copy the line of code from ocelot.c which does the one-shot
initialization of the flooding PGIDs, and we add it to felix.c as well -
except replicated 8 times.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add wave programming registers definitions for Ocelot platforms.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Ocelot PTP clock driver had been embedded into ocelot.c driver.
It had supported basic gettime64/settime64/adjtime/adjfine functions
by now which were used by both Ocelot switch and Felix switch.
This patch is to move current ptp clock code out of ocelot.c driver
maintaining as a single ocelot_ptp.c.
For futher new features implementation, the common code could be put
in ocelot_ptp.c and the switch specific code should be in specific
switch driver. The interrupt implementation in SoC is different
between Ocelot and Felix.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
