[ Upstream commit 589918df93226a1e5f104306c185b6dcf2bd8051 ]
Similar but not quite the same with what was done in commit b11f0a4c0c81
("net: dsa: sja1105: be stateless when installing FDB entries") for
SJA1105E/T, it is desirable to drop the priv->vlan_aware check and
simply go ahead and install FDB entries in the VLAN that was given by
the bridge.
As opposed to SJA1105E/T, in SJA1105P/Q/R/S and SJA1110, the FDB is a
maskable TCAM, and we are installing VLAN-unaware FDB entries with the
VLAN ID masked off. However, such FDB entries might completely obscure
VLAN-aware entries where the VLAN ID is included in the search mask,
because the switch looks up the FDB from left to right and picks the
first entry which results in a masked match. So it depends on whether
the bridge installs first the VLAN-unaware or the VLAN-aware FDB entries.
Anyway, if we had a VLAN-unaware FDB entry towards one set of DESTPORTS
and a VLAN-aware one towards other set of DESTPORTS, the result is that
the packets in VLAN-aware mode will be forwarded towards the DESTPORTS
specified by the VLAN-unaware entry.
To solve this, simply do not use the masked matching ability of the FDB
for VLAN ID, and always match precisely on it. In VLAN-unaware mode, we
configure the switch for shared VLAN learning, so the VLAN ID will be
ignored anyway during lookup, so it is redundant to mask it off in the
TCAM.
This patch conflicts with net-next commit 0fac6aa098ed ("net: dsa: sja1105:
delete the best_effort_vlan_filtering mode") which changed this line:
if (priv->vlan_state != SJA1105_VLAN_UNAWARE) {
into:
if (priv->vlan_aware) {
When merging with net-next, the lines added by this patch should take
precedence in the conflict resolution (i.e. the "if" condition should be
deleted in both cases).
Fixes: 1da7382134 ("net: dsa: sja1105: Add FDB operations for P/Q/R/S series")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6c5fc159e0927531707895709eee1f8bfa04289f ]
The procedure to add a static FDB entry in sja1105 is concurrent with
dynamic learning performed on all bridge ports and the CPU port.
The switch looks up the FDB from left to right, and also learns
dynamically from left to right, so it is possible that between the
moment when we pick up a free slot to install an FDB entry, another slot
to the left of that one becomes free due to an address ageing out, and
that other slot is then immediately used by the switch to learn
dynamically the same address as we're trying to add statically.
The result is that we succeeded to add our static FDB entry, but it is
being shadowed by a dynamic FDB entry to its left, and the switch will
behave as if our static FDB entry did not exist.
We cannot really prevent this from happening unless we make the entire
process to add a static FDB entry a huge critical section where address
learning is temporarily disabled on _all_ ports, and then re-enabled
according to the configuration done by sja1105_port_set_learning.
However, that is kind of disruptive for the operation of the network.
What we can do alternatively is to simply read back the FDB for dynamic
entries located before our newly added static one, and delete them.
This will guarantee that our static FDB entry is now operational. It
will still not guarantee that there aren't dynamic FDB entries to the
_right_ of that static FDB entry, but at least those entries will age
out by themselves since they aren't hit, and won't bother anyone.
Fixes: 291d1e72b7 ("net: dsa: sja1105: Add support for FDB and MDB management")
Fixes: 1da7382134 ("net: dsa: sja1105: Add FDB operations for P/Q/R/S series")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e11e865bf84e3c6ea91563ff3e858cfe0e184bd2 ]
The SJA1105 switch family leaves it up to software to decide where
within the FDB to install a static entry, and to concatenate destination
ports for already existing entries (the FDB is also used for multicast
entries), it is not as simple as just saying "please add this entry".
This means we first need to search for an existing FDB entry before
adding a new one. The driver currently manages to fool itself into
thinking that if an FDB entry already exists, there is nothing to be
done. But that FDB entry might be dynamically learned, case in which it
should be replaced with a static entry, but instead it is left alone.
This patch checks the LOCKEDS ("locked/static") bit from found FDB
entries, and lets the code "goto skip_finding_an_index;" if the FDB
entry was not static. So we also need to move the place where we set
LOCKEDS = true, to cover the new case where a dynamic FDB entry existed
but was dynamic.
Fixes: 291d1e72b7 ("net: dsa: sja1105: Add support for FDB and MDB management")
Fixes: 1da7382134 ("net: dsa: sja1105: Add FDB operations for P/Q/R/S series")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d51c5907e9809a803b276883d203f45849abd4d6 ]
GSO expects inner transport header offset to be valid when
skb->encapsulation flag is set. GSO uses this value to calculate the length
of an individual segment of a GSO packet in skb_gso_transport_seglen().
However, tcp/udp gro_complete callbacks don't update the
skb->inner_transport_header when processing an encapsulated TCP/UDP
segment. As a result a GRO skb has ->inner_transport_header set to a value
carried over from earlier skb processing.
This can have mild to tragic consequences. From miscalculating the GSO
segment length to triggering a page fault [1], when trying to read TCP/UDP
header at an address past the skb->data page.
The latter scenario leads to an oops report like so:
BUG: unable to handle page fault for address: ffff9fa7ec00d008
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 123f201067 P4D 123f201067 PUD 123f209067 PMD 0
Oops: 0000 [#1] SMP NOPTI
CPU: 44 PID: 0 Comm: swapper/44 Not tainted 5.4.53-cloudflare-2020.7.21 #1
Hardware name: HYVE EDGE-METAL-GEN10/HS-1811DLite1, BIOS V2.15 02/21/2020
RIP: 0010:skb_gso_transport_seglen+0x44/0xa0
Code: c0 41 83 e0 11 f6 87 81 00 00 00 20 74 30 0f b7 87 aa 00 00 00 0f [...]
RSP: 0018:ffffad8640bacbb8 EFLAGS: 00010202
RAX: 000000000000feda RBX: ffff9fcc8d31bc00 RCX: ffff9fa7ec00cffc
RDX: ffff9fa7ebffdec0 RSI: 000000000000feda RDI: 0000000000000122
RBP: 00000000000005c4 R08: 0000000000000001 R09: 0000000000000000
R10: ffff9fe588ae3800 R11: ffff9fe011fc92f0 R12: ffff9fcc8d31bc00
R13: ffff9fe0119d4300 R14: 00000000000005c4 R15: ffff9fba57d70900
FS: 0000000000000000(0000) GS:ffff9fe68df00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffff9fa7ec00d008 CR3: 0000003e99b1c000 CR4: 0000000000340ee0
Call Trace:
<IRQ>
skb_gso_validate_network_len+0x11/0x70
__ip_finish_output+0x109/0x1c0
ip_sublist_rcv_finish+0x57/0x70
ip_sublist_rcv+0x2aa/0x2d0
? ip_rcv_finish_core.constprop.0+0x390/0x390
ip_list_rcv+0x12b/0x14f
__netif_receive_skb_list_core+0x2a9/0x2d0
netif_receive_skb_list_internal+0x1b5/0x2e0
napi_complete_done+0x93/0x140
veth_poll+0xc0/0x19f [veth]
? mlx5e_napi_poll+0x221/0x610 [mlx5_core]
net_rx_action+0x1f8/0x790
__do_softirq+0xe1/0x2bf
irq_exit+0x8e/0xc0
do_IRQ+0x58/0xe0
common_interrupt+0xf/0xf
</IRQ>
The bug can be observed in a simple setup where we send IP/GRE/IP/TCP
packets into a netns over a veth pair. Inside the netns, packets are
forwarded to dummy device:
trafgen -> [veth A]--[veth B] -forward-> [dummy]
For veth B to GRO aggregate packets on receive, it needs to have an XDP
program attached (for example, a trivial XDP_PASS). Additionally, for UDP,
we need to enable GSO_UDP_L4 feature on the device:
ip netns exec A ethtool -K AB rx-udp-gro-forwarding on
The last component is an artificial delay to increase the chances of GRO
batching happening:
ip netns exec A tc qdisc add dev AB root \
netem delay 200us slot 5ms 10ms packets 2 bytes 64k
With such a setup in place, the bug can be observed by tracing the skb
outer and inner offsets when GSO skb is transmitted from the dummy device:
tcp:
FUNC DEV SKB_LEN NH TH ENC INH ITH GSO_SIZE GSO_TYPE
ip_finish_output dumB 2830 270 290 1 294 254 1383 (tcpv4,gre,)
^^^
udp:
FUNC DEV SKB_LEN NH TH ENC INH ITH GSO_SIZE GSO_TYPE
ip_finish_output dumB 2818 270 290 1 294 254 1383 (gre,udp_l4,)
^^^
Fix it by updating the inner transport header offset in tcp/udp
gro_complete callbacks, similar to how {inet,ipv6}_gro_complete callbacks
update the inner network header offset, when skb->encapsulation flag is
set.
[1] https://lore.kernel.org/netdev/CAKxSbF01cLpZem2GFaUaifh0S-5WYViZemTicAg7FCHOnh6kug@mail.gmail.com/
Fixes: bf296b125b ("tcp: Add GRO support")
Fixes: f993bc25e5 ("net: core: handle encapsulation offloads when computing segment lengths")
Fixes: e20cf8d3f1 ("udp: implement GRO for plain UDP sockets.")
Reported-by: Alex Forster <aforster@cloudflare.com>
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7199ddede9f0f2f68d41e6928e1c6c4bca9c39c0 ]
Commit dea7a9fbb0 ("dmaengine: imx-dma: remove dma_slave_config
direction usage") changes the method from a "configuration when called"
to an "configuration when used". Due to this, only the cyclic DMA type
gets configured correctly, while the generic DMA type is left
non-configured.
Without this additional call, the struct imxdma_channel::word_size member
is stuck at DMA_SLAVE_BUSWIDTH_UNDEFINED and imxdma_prep_slave_sg() always
returns NULL.
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Fixes: dea7a9fbb0 ("dmaengine: imx-dma: remove dma_slave_config direction usage")
Link: https://lore.kernel.org/r/20210729071821.9857-1-jbe@pengutronix.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 15f68f027ebd961b99a1c420f96ff3838c5e4450 ]
While 7e5f3155dc ("ARM: dts: stm32: Fix LED5 on STM32MP1 DHCOM PDK2")
fixed the LED0 assignment on the PDK2 board, the same commit did not
update the touchscreen IRQ line assignment, which is the same GPIO line,
shared between the LED0 output and touchscreen IRQ input. To make this
more convoluted, the same EXTI input (not the same GPIO line) is shared
between Button B which is Active-Low IRQ, and touchscreen IRQ which is
Edge-Falling IRQ, which cannot be used at the same time. In case the LCD
board with touchscreen is in use, which is the case here, LED0 must be
disabled, Button B must be polled, so the touchscreen interrupt works as
it should.
Update the touchscreen IRQ line assignment, disable LED0 and use polled
GPIO button driver for Button B, since the DT here describes baseboard
with LCD board.
Fixes: 7e5f3155dc ("ARM: dts: stm32: Fix LED5 on STM32MP1 DHCOM PDK2")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 36862c1ebc92a7e6fcc55002965c44b8ad17d4ca ]
The LAN8710 Energy Detect Power Down (EDPD) functionality might cause
unreliable cable detection. There are multiple accounts of this in the
SMSC PHY driver patches which attempted to make EDPD reliable, however
it seems there is always some sort of corner case left. Unfortunatelly,
there is no errata documented which would confirm this to be a silicon
bug on the LAN87xx series of PHYs (LAN8700, LAN8710, LAN8720 at least).
Disable EDPD on the DHCOM SoM, just like multiple other boards already
do as well, to make the cable detection reliable.
Fixes: 34e0c7847d ("ARM: dts: stm32: Add DH Electronics DHCOM STM32MP1 SoM and PDK2 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c592b46907adbeb81243f7eb7a468c36692658b8 ]
If a vb2_queue sets q->min_buffers_needed then when the number of
queued buffers reaches q->min_buffers_needed, vb2_core_qbuf() will call
the start_streaming() callback. If start_streaming() returns an error,
then that error was just returned by vb2_core_qbuf(), but the buffer
was still queued. However, userspace expects that if VIDIOC_QBUF fails,
the buffer is returned dequeued.
So if start_streaming() fails, then remove the buffer from the queue,
thus avoiding this unwanted side-effect.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Fixes: b3379c6201 ("[media] vb2: only call start_streaming if sufficient buffers are queued")
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5c04243a56a7977185b00400e59ca7e108004faf ]
Media event code 3 is defined in the MMC-6 spec as follows:
"MediaRemoval: The media has been removed from the specified slot, and
the Drive is unable to access the media without user intervention. This
applies to media changers only."
This indicated that treating the condition as an EJECT_REQUEST was
appropriate. However, doing so had the unfortunate side-effect of causing
the drive tray to be physically ejected on resume. Instead treat the event
as a MEDIA_CHANGE request.
Fixes: 7dd753ca59d6 ("scsi: sr: Return appropriate error code when disk is ejected")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=213759
Link: https://lore.kernel.org/r/20210726114913.6760-1-limanyi@uniontech.com
Signed-off-by: Li Manyi <limanyi@uniontech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 53ca18acbe645656132fb5a329833db711067e54 ]
The spi_imx->spi_bus_clk may be uninitialized and thus also zero in
mx51_ecspi_prepare_message(), which would lead to division by zero
in kernel. Since bitbang .setup_transfer callback which initializes
the spi_imx->spi_bus_clk is called after bitbang prepare_message
callback, iterate over all the transfers in spi_message, find the
one with lowest bus frequency, and use that bus frequency for the
delay calculation.
Note that it is not possible to move this CONFIGREG delay back into
the .setup_transfer callback, because that is invoked too late, after
the GPIO chipselects were already configured.
Fixes: 135cbd378eab ("spi: imx: mx51-ecspi: Reinstate low-speed CONFIGREG delay")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210726100102.5188-1-marex@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 135cbd378eab336da15de9c84bbb22bf743b38a5 ]
Since 00b80ac935 ("spi: imx: mx51-ecspi: Move some initialisation to
prepare_message hook."), the MX51_ECSPI_CONFIG write no longer happens
in prepare_transfer hook, but rather in prepare_message hook, however
the MX51_ECSPI_CONFIG delay is still left in prepare_transfer hook and
thus has no effect. This leads to low bus frequency operation problems
described in 6fd8b8503a ("spi: spi-imx: Fix out-of-order CS/SCLK
operation at low speeds") again.
Move the MX51_ECSPI_CONFIG write delay into the prepare_message hook
as well, thus reinstating the low bus frequency fix.
Fixes: 00b80ac935 ("spi: imx: mx51-ecspi: Move some initialisation to prepare_message hook.")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210703022300.296114-1-marex@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit baa16371c9525f24d508508e4d296c031e1de29c ]
pm_runtime_get_sync will increment pm usage counter
even it failed. Forgetting to putting operation will
result in reference leak here. We fix it by replacing
it with pm_runtime_resume_and_get to keep usage counter
balanced.
Fixes: 4f3ceca254 ("dmaengine: stm32-dmamux: Add PM Runtime support")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20210607064640.121394-3-zhangqilong3@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d54db74ad6e0dea8c253fb68c689b836657ab914 ]
pm_runtime_get_sync will increment pm usage counter
even it failed. Forgetting to putting operation will
result in reference leak here. We fix it by replacing
it with pm_runtime_resume_and_get to keep usage counter
balanced.
Fixes: 48bc73ba14 ("dmaengine: stm32-dma: Add PM Runtime support")
Fixes: 05f8740a0e ("dmaengine: stm32-dma: add suspend/resume power management support")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20210607064640.121394-2-zhangqilong3@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 55f24c27b6c1a840b62fe297616f1f9ea3576cb7 ]
The function uniphier_xdmac_chan_stop() is only called in atomic state.
Should use readl_poll_timeout_atomic() there instead of
readl_poll_timeout().
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 667b925144 ("dmaengine: uniphier-xdmac: Add UniPhier external DMA controller driver")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/1627364852-28432-1-git-send-email-hayashi.kunihiko@socionext.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c68ef4ad180e09805fa46965d15e1dfadf09ffa5 ]
This device tree include file describes a fixed-regulator
connecting smps7_reg output (1.8V) to some 1.8V rail and
consumers (vdds_1v8_main).
This regulator does not physically exist.
I assume it was introduced as a wrapper around smps7_reg
to provide a speaking signal name "vdds_1v8_main" as label.
This fixed-regulator without real function was not an issue
in driver code until
Commit 98e48cd9283d ("regulator: core: resolve supply for boot-on/always-on regulators")
introduced a new check for regulator initialization which
makes Palmas regulator registration fail:
[ 5.407712] ldo1: supplied by vsys_cobra
[ 5.412748] ldo2: supplied by vsys_cobra
[ 5.417603] palmas-pmic 48070000.i2c:palmas@48:palmas_pmic: failed to register 48070000.i2c:palmas@48:palmas_pmic regulator
The reason is that the supply-chain of regulators is too
long and goes from ldo3 through the virtual vdds_1v8_main
regulator and then back to smps7. This adds a cross-dependency
of probing Palmas regulators and the fixed-regulator which
leads to probe deferral by the new check and is no longer
resolved.
Since we do not control what device tree files including this
one reference (either &vdds_1v8_main or &smps7_reg or both)
we keep both labels for smps7 for compatibility.
Fixes: 98e48cd9283d ("regulator: core: resolve supply for boot-on/always-on regulators")
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 24b5b1978cd5a80db58e2a19db2f9c36fe8d4f7a ]
Enabling the framebuffer leads to a system hang. Running, as a debug
hack, the store_pan() function in drivers/video/fbdev/core/fbsysfs.c
without taking the console_lock, allows to see the crash backtrace on
the serial line.
~ # echo 0 0 > /sys/class/graphics/fb0/pan
[ 9.719414] Unhandled exception: IPSR = 00000005 LR = fffffff1
[ 9.726937] CPU: 0 PID: 49 Comm: sh Not tainted 5.13.0-rc5 #9
[ 9.733008] Hardware name: STM32 (Device Tree Support)
[ 9.738296] PC is at clk_gate_is_enabled+0x0/0x28
[ 9.743426] LR is at stm32f4_pll_div_set_rate+0xf/0x38
[ 9.748857] pc : [<0011e4be>] lr : [<0011f9e3>] psr: 0100000b
[ 9.755373] sp : 00bc7be0 ip : 00000000 fp : 001f3ac4
[ 9.760812] r10: 002610d0 r9 : 01efe920 r8 : 00540560
[ 9.766269] r7 : 02e7ddb0 r6 : 0173eed8 r5 : 00000000 r4 : 004027c0
[ 9.773081] r3 : 0011e4bf r2 : 02e7ddb0 r1 : 0173eed8 r0 : 1d3267b8
[ 9.779911] xPSR: 0100000b
[ 9.782719] CPU: 0 PID: 49 Comm: sh Not tainted 5.13.0-rc5 #9
[ 9.788791] Hardware name: STM32 (Device Tree Support)
[ 9.794120] [<0000afa1>] (unwind_backtrace) from [<0000a33f>] (show_stack+0xb/0xc)
[ 9.802421] [<0000a33f>] (show_stack) from [<0000a8df>] (__invalid_entry+0x4b/0x4c)
The `pll_num' field in the post_div_data configuration contained a wrong
value which also referenced an uninitialized hardware clock when
clk_register_pll_div() was called.
Fixes: 517633ef63 ("clk: stm32f4: Add post divisor for I2S & SAI PLLs")
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Link: https://lore.kernel.org/r/20210725160725.10788-1-dariobin@libero.it
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4511781f95da0a3b2bad34f3f5e3967e80cd2d18 ]
The following scenario describes an echo test for
Samsung USBC Headset (AKG) with VID/PID (0x04e8/0xa051).
We first start a capture stream(USB IN transfer) in 96Khz/24bit/1ch mode.
In clock find source function, we get value 0x2 for clock selector
and 0x1 for clock source.
Kernel-4.14 behavior
Since clock source is valid so clock selector was not set again.
We pass through this function and start a playback stream(USB OUT transfer)
in 48Khz/32bit/2ch mode. This time we get value 0x1 for clock selector
and 0x1 for clock source. Finally clock id with this setting is 0x9.
Kernel-5.10 behavior
Clock selector was always set one more time even it is valid.
When we start a playback stream, we will get 0x2 for clock selector
and 0x1 for clock source. In this case clock id becomes 0xA.
This is an incorrect clock source setting and results in severe noises.
We see wrong data rate in USB IN transfer.
(From 288 bytes/ms becomes 144 bytes/ms) It should keep in 288 bytes/ms.
This earphone works fine on older kernel version load because
this is a newly-added behavior.
Fixes: d2e8f641257d ("ALSA: usb-audio: Explicitly set up the clock selector")
Signed-off-by: chihhao.chen <chihhao.chen@mediatek.com>
Link: https://lore.kernel.org/r/1627100621-19225-1-git-send-email-chihhao.chen@mediatek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ee7ab3f263f8131722cff3871b9618b1e7478f07 ]
Some SFP modules are not detected when i2c-fast-mode is enabled even when
clock-frequency is already set to 100000. The I2C bus violates the timing
specifications when run in fast mode. So disable fast mode on Turris Mox.
Same change was already applied for uDPU (also Armada 3720 board with SFP)
in commit fe3ec631a7 ("arm64: dts: uDPU: remove i2c-fast-mode").
Fixes: 7109d817db ("arm64: dts: marvell: add DTS for Turris Mox")
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <kabel@kernel.org>
Acked-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 923f98929182dfd04e9149be839160b63a3db145 ]
Since drivers/mmc/host/sdhci-xenon.c declares the PROBE_PREFER_ASYNCHRONOUS
probe type, it is not guaranteed whether /dev/mmcblk0 will belong to
sdhci0 or sdhci1. In turn, this will break booting by:
root=/dev/mmcblk0p1
Fix the issue by adding aliases so that the old MMC controller indices
are preserved.
Fixes: 7320915c88 ("mmc: Set PROBE_PREFER_ASYNCHRONOUS for drivers that existed in v4.14")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3d9e30a52047f2d464efdfd1d561ae1f707a0286 ]
The pinctrl_power_button/pinctrl_power_out each define single GPIO
pinmux, except it is exactly the other one than the matching gpio-keys
and gpio-poweroff DT nodes use for that functionality. Swap the two
GPIOs to correct this error.
Fixes: 50d29fdb76 ("ARM: dts: imx53: Add power GPIOs on M53Menlo")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 20fb73911fec01f06592de1cdbca00b66602ebd7 ]
The function imx_mmdc_perf_init recently had a 3rd argument added to
it but the equivalent macro was not updated and is still the older
2 argument version. Fix this by adding in the missing 3rd argumement
mmdc_ipg_clk.
Fixes: f07ec8536580 ("ARM: imx: add missing clk_disable_unprepare()")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 29f6a20c21b5bdc7eb623a712bbf7b99612ee746 ]
The PHY configuration for the variant 2 is still missing the flag for
in-band signalling between PHY and MAC. Both sides - MAC and PHY - have
to match the setting. For now, Linux only supports setting the MAC side
and thus it has to match the setting the bootloader is configuring.
Enable in-band signalling to make ethernet work.
Fixes: ab43f03074 ("arm64: dts: ls1028a: sl28: add support for variant 2")
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fd8e83884fdd7b5fc411f201a58d8d01890198a2 ]
The AR803x PHY used on this modules seems to require the reset line to
be asserted for around 10ms in order to avoid rare cases where the PHY
gets stuck in an incoherent state that prevents it to function
correctly.
The previous value of 2ms was found to be problematic on some setups,
causing intermittent issues where the PHY would be unresponsive
every once in a while on some sytems, with a low occurrence (it typically
took around 30 consecutive reboots to encounter the issue).
Bumping the delay to the 10ms makes the issue dissapear, with more than
2500 consecutive reboots performed without the issue showing-up.
Fixes: 208d7baf80 ("ARM: imx: initial SolidRun HummingBoard support")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Hervé Codina <herve.codina@bootlin.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f07ec85365807b3939f32d0094a6dd5ce065d1b9 ]
clock source is prepared and enabled by clk_prepare_enable()
in probe function, but no disable or unprepare in remove and
error path.
Fixes: 9454a0caff ("ARM: imx: add mmdc ipg clock operation for mmdc")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f9613aa07f16d6042e74208d1b40a6104d72964a ]
Commit e76bdfd740 ("ARM: imx: Added perf functionality to mmdc driver")
introduced imx_mmdc_remove(), the mmdc_base need be unmapped in it if
config PERF_EVENTS is enabled.
If imx_mmdc_perf_init() fails, the mmdc_base also need be unmapped.
Fixes: e76bdfd740 ("ARM: imx: Added perf functionality to mmdc driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7e71b85473f863a29eb1c69265ef025389b4091d ]
U-Boot attempts to fix up the "clock-frequency" property of the "/sysclk" node:
https://elixir.bootlin.com/u-boot/v2021.04/source/arch/arm/cpu/armv8/fsl-layerscape/fdt.c#L512
but fails to do so:
## Booting kernel from Legacy Image at a1000000 ...
Image Name:
Created: 2021-06-08 10:31:38 UTC
Image Type: AArch64 Linux Kernel Image (gzip compressed)
Data Size: 15431370 Bytes = 14.7 MiB
Load Address: 80080000
Entry Point: 80080000
Verifying Checksum ... OK
## Flattened Device Tree blob at a0000000
Booting using the fdt blob at 0xa0000000
Uncompressing Kernel Image
Loading Device Tree to 00000000fbb19000, end 00000000fbb22717 ... OK
Unable to update property /sysclk:clock-frequency, err=FDT_ERR_NOTFOUND
Starting kernel ...
All Layerscape SoCs except LS1028A use "sysclk" as the node name, and
not "clock-sysclk". So change the node name of LS1028A accordingly.
Fixes: 8897f3255c ("arm64: dts: Add support for NXP LS1028A SoC")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7c1a80e80cde008f271bae630d28cf684351e807 ]
Syzbot reported memory leak in xfrm_user_rcv_msg(). The
problem was is non-freed skb's frag_list.
In skb_release_all() skb_release_data() will be called only
in case of skb->head != NULL, but netlink_skb_destructor()
sets head to NULL. So, allocated frag_list skb should be
freed manualy, since consume_skb() won't take care of it
Fixes: 5106f4a8ac ("xfrm/compat: Add 32=>64-bit messages translator")
Reported-and-tested-by: syzbot+fb347cf82c73a90efcca@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ff340e24c9dd5cff9fc07d67914c5adf67f80d6 ]
Jarkko Nikula <jarkko.nikula@bitmer.com> reported that Beagleboard
revision c2 stopped booting. Jarkko bisected the issue down to
commit 6cfcd5563b ("clocksource/drivers/timer-ti-dm: Fix suspend
and resume for am3 and am4").
Let's fix the issue by tagging system timers as reserved rather than
ignoring them. And let's not probe any interconnect target module child
devices for reserved modules.
This allows PM runtime to keep track of clocks and clockdomains for
the interconnect target module, and prevent the system timer from idling
as we already have SYSC_QUIRK_NO_IDLE and SYSC_QUIRK_NO_IDLE_ON_INIT
flags set for system timers.
Fixes: 6cfcd5563b ("clocksource/drivers/timer-ti-dm: Fix suspend and resume for am3 and am4")
Reported-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Tested-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 97367c97226aab8b298ada954ce12659ee3ad2a4 upstream.
It turned out that the current implementation of the port subscription
is racy. The subscription contains two linked lists, and we have to
add to or delete from both lists. Since both connection and
disconnection procedures perform the same order for those two lists
(i.e. src list, then dest list), when a deletion happens during a
connection procedure, the src list may be deleted before the dest list
addition completes, and this may lead to a use-after-free or an Oops,
even though the access to both lists are protected via mutex.
The simple workaround for this race is to change the access order for
the disconnection, namely, dest list, then src list. This assures
that the connection has been established when disconnecting, and also
the concurrent deletion can be avoided.
Reported-and-tested-by: folkert <folkert@vanheusden.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210801182754.GP890690@belle.intranet.vanheusden.com
Link: https://lore.kernel.org/r/20210803114312.2536-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6511a8b5b7a65037340cd8ee91a377811effbc83 upstream.
Revert commit c27bac0314131 ("ACPICA: Fix memory leak caused by _CID
repair function") which is reported to cause a boot issue on Acer
Swift 3 (SF314-51).
Reported-by: Adrien Precigout <dev@asdrip.fr>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0d5c3954b35eddff0da0436c31e8d721eceb7dc2 upstream.
Commit 3a70dd2d0503 ("spi: mediatek: fix fifo rx mode") claims that
fifo RX mode was never handled, and adds the presumably missing code
to the FIFO transfer function. However, the claim that receive data
was not handled is incorrect. It was handled as part of interrupt
handling after the transfer was complete. The code added with the above
mentioned commit reads data from the receive FIFO before the transfer
is started, which is wrong. This results in an actual transfer error
on a Hayato Chromebook.
Remove the code trying to handle receive data before the transfer is
started to fix the problem.
Fixes: 3a70dd2d0503 ("spi: mediatek: fix fifo rx mode")
Cc: Peter Hess <peter.hess@ph-home.de>
Cc: Frank Wunderlich <frank-w@public-files.de>
Cc: Tzung-Bi Shih <tzungbi@google.com>
Cc: Hsin-Yi Wang <hsinyi@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Hsin-Yi Wang <hsinyi@google.com>
Tested-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20210802030023.1748777-1-linux@roeck-us.net
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7a22930c4179b51352f2ec9feb35167cbe79afd9 upstream
Add tests for the new functionality - reading and writing to the stack
through a variable-offset pointer.
Signed-off-by: Andrei Matei <andreimatei1@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20210207011027.676572-4-andreimatei1@gmail.com
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 973377ffe8148180b2651825b92ae91988141b05 upstream
In almost all cases from test_verifier that have been changed in here, we've
had an unreachable path with a load from a register which has an invalid
address on purpose. This was basically to make sure that we never walk this
path and to have the verifier complain if it would otherwise. Change it to
match on the right error for unprivileged given we now test these paths
under speculative execution.
There's one case where we match on exact # of insns_processed. Due to the
extra path, this will of course mismatch on unprivileged. Thus, restrict the
test->insn_processed check to privileged-only.
In one other case, we result in a 'pointer comparison prohibited' error. This
is similarly due to verifying an 'invalid' branch where we end up with a value
pointer on one side of the comparison.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d7a5091351756d0ae8e63134313c455624e36a13 upstream
Update various selftest error messages:
* The 'Rx tried to sub from different maps, paths, or prohibited types'
is reworked into more specific/differentiated error messages for better
guidance.
* The change into 'value -4294967168 makes map_value pointer be out of
bounds' is due to moving the mixed bounds check into the speculation
handling and thus occuring slightly later than above mentioned sanity
check.
* The change into 'math between map_value pointer and register with
unbounded min value' is similarly due to register sanity check coming
before the mixed bounds check.
* The case of 'map access: known scalar += value_ptr from different maps'
now loads fine given masks are the same from the different paths (despite
max map value size being different).
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1bad6fd52be4ce12d207e2820ceb0f29ab31fc53 upstream
Given we don't need to simulate the speculative domain for registers with
immediates anymore since the verifier uses direct imm-based rewrites instead
of having to mask, we can also lift a few cases that were previously rejected.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a680cb3d8e3f4f84205720b90c926579d04eedb6 upstream
The verifier errors around stack accesses have changed slightly in the
previous commit (generally for the better).
Signed-off-by: Andrei Matei <andreimatei1@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20210207011027.676572-3-andreimatei1@gmail.com
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b4b638c36b7e7acd847b9c4b9c80f268e45ea30c upstream
Change bpf_iter_task.c such that pointer to map_value may appear
on the stack for bpf_seq_printf() to access. Without previous
verifier patch, the bpf_iter test will fail.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20201210013350.943985-1-yhs@fb.com
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 39ed17de8c which is
commit cb011044e34c293e139570ce5c01aed66a34345c upstream.
It is reported to cause problems with systems and probably should not
have been backported in the first place :(
Link: https://lore.kernel.org/r/20210803165108.4154cd52@endymion
Reported-by: Jean Delvare <jdelvare@suse.de>
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Wim Van Sebroeck <wim@linux-watchdog.org>
Cc: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f1748b1ee1fa0fd1a074504045b530b62f949188 upstream.
A successfully received delayed response could anyway report a failure at
the protocol layer in the message status field.
Add a check also for this error condition.
Link: https://lore.kernel.org/r/20210608103056.3388-1-cristian.marussi@arm.com
Fixes: 58ecdf03db ("firmware: arm_scmi: Add support for asynchronous commands and delayed response")
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5e469dac326555d2038d199a6329458cc82a34e5 upstream.
The bus probe callback calls the driver callback without further
checking. Better be safe than sorry and refuse registration of a driver
without a probe function to prevent a NULL pointer exception.
Link: https://lore.kernel.org/r/20210624095059.4010157-2-sudeep.holla@arm.com
Fixes: 933c504424 ("firmware: arm_scmi: add scmi protocol bus to enumerate protocol devices")
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested-by: Cristian Marussi <cristian.marussi@arm.com>
Reviewed-by: Cristian Marussi <cristian.marussi@arm.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fc68f42aa737dc15e7665a4101d4168aadb8e4c4 ]
Commit 71f642833284 ("ACPI: utils: Fix reference counting in
for_each_acpi_dev_match()") started doing "acpi_dev_put()" on a pointer
that was possibly NULL. That fails miserably, because that helper
inline function is not set up to handle that case.
Just make acpi_dev_put() silently accept a NULL pointer, rather than
calling down to put_device() with an invalid offset off that NULL
pointer.
Link: https://lore.kernel.org/lkml/a607c149-6bf6-0fd0-0e31-100378504da2@kernel.dk/
Reported-and-tested-by: Jens Axboe <axboe@kernel.dk>
Tested-by: Daniel Scally <djrscally@gmail.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d7940911fc0754d99b208f0e3098762d39f403a0 ]
[Why]
Vertical and horizontal borders in timings are treated as increasing the
active area - vblank and hblank actually shrink.
Our input into DML does not include these borders so it incorrectly
assumes it has more time than available for vstartup and tmdl
calculations for some modes with borders.
An example of such a timing would be 640x480@72Hz:
h_total: 832
h_border_left: 8
h_addressable: 640
h_border_right: 8
h_front_porch: 16
h_sync_width: 40
v_total: 520
v_border_top: 8
v_addressable: 480
v_border_bottom: 8
v_front_porch: 1
v_sync_width: 3
pix_clk_100hz: 315000
[How]
Include borders as part of destination vactive/hactive.
This change DCN20+ so it has wide impact, but the destination vactive
and hactive are only really used for vstartup calculation anyway.
Most modes do not have vertical or horizontal borders.
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ec3102dc6b36c692104c4a0546d4119de59a3bc1 ]
[why]
A comparison error made it possible to not iterate through all the
specified prefetch modes.
[how]
Correct "<" to "<="
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Yongqiang Sun <Yongqiang.Sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Victor Lu <victorchengchi.lu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 234211b8dd161fa25f192c78d5a8d2dd6bf920a0 ]
The metadata address is set after the trace event, so the trace is not
capturing anything useful. Rather than logging the memory address, it's
useful to know if the command carries a metadata payload, so change the
trace event to log that true/false state instead.
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 47e1e233e9d822dfda068383fb9a616451bda703 ]
One of the SUSE QA tests triggered:
localhost kernel: efi: Failed to lookup EFI memory descriptor for 0x000000003dcf8000
which comes from x86's version of efi_arch_mem_reserve() trying to
reserve a memory region. Usually, that function expects
EFI_BOOT_SERVICES_DATA memory descriptors but the above case is for the
MOKvar table which is allocated in the EFI shim as runtime services.
That lead to a fix changing the allocation of that table to boot services.
However, that fix broke booting SEV guests with that shim leading to
this kernel fix
8d651ee9c71b ("x86/ioremap: Map EFI-reserved memory as encrypted for SEV")
which extended the ioremap hint to map reserved EFI boot services as
decrypted too.
However, all that wasn't needed, IMO, because that error message in
efi_arch_mem_reserve() was innocuous in this case - if the MOKvar table
is not in boot services, then it doesn't need to be reserved in the
first place because it is, well, in runtime services which *should* be
reserved anyway.
So do that reservation for the MOKvar table only if it is allocated
in boot services data. I couldn't find any requirement about where
that table should be allocated in, unlike the ESRT which allocation is
mandated to be done in boot services data by the UEFI spec.
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 82d28b67f780910f816fe1cfb0f676fc38c4cbb3 ]
During probe the parent_clk_id is set to -1 which should not be used to
array index within hsdiv_rates[].
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Link: https://lore.kernel.org/r/20210717122820.1467-3-peter.ujfalusi@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
