Now that DMA1 is defined, use it to distribute channel usage among the two
controllers.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The sama5d2 SoC has a second DMA controller and can be used just like DMA0.
By default both DMA controllers are configured as "Secure" in
MATRIX_SPSELR so we can use whichever we want in a "single Secure World"
configuration.
Surprisingly the DMA1 has a lower address than DMA0. To avoid confusion
place it after DMA0 node anyway.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Enable UART1 and use DMA configuration with it.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Some peripherals are "Programmable Secure" but left as "Secure" by default.
If tried to be connected to Non-Secure DMA controller, the possibility to
leak secure data is prevented so using these peripherals with DMA1 is not
possible with this default configuration (MATRIX_SPSELR registers setup by
bootloader).
Move them to DMA0 which is an "Always-Secure" DMA controller.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The new size (0x100) also matches the size given in sama5d3.dtsi
Documentation reference: section 43.6 "Universal Asynchronous
Receiver Transmitter (UART) User Interface", table 43-4 "Register
Mapping" in [1].
[1] Atmel-11121F-ATARM-SAMA5D3-Series-Datasheet_02-Feb-16
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
I am getting the following warning when I build kernel 4.9-git on my
PowerBook G4 with a 32-bit PPC processor:
AS arch/powerpc/kernel/misc_32.o
arch/powerpc/kernel/misc_32.S:299:7: warning: "CONFIG_FSL_BOOKE" is not defined [-Wundef]
This problem is evident after commit 989cea5c14 ("kbuild: prevent
lib-ksyms.o rebuilds"); however, this change in kbuild only exposes an
error that has been in the code since 2005 when this source file was
created. That was with commit 9994a33865 ("powerpc: Introduce
entry_{32,64}.S, misc_{32,64}.S, systbl.S").
The offending line does not make a lot of sense. This error does not
seem to cause any errors in the executable, thus I am not recommending
that it be applied to any stable versions.
Thanks to Nicholas Piggin for suggesting this solution.
Fixes: 9994a33865 ("powerpc: Introduce entry_{32,64}.S, misc_{32,64}.S, systbl.S")
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The timer type simplifications caused a new gcc warning:
drivers/base/power/domain.c: In function ‘genpd_runtime_suspend’:
drivers/base/power/domain.c:562:14: warning: ‘time_start’ may be used uninitialized in this function [-Wmaybe-uninitialized]
elapsed_ns = ktime_to_ns(ktime_sub(ktime_get(), time_start));
despite the actual use of "time_start" not having changed in any way.
It appears that simply changing the type of ktime_t from a union to a
plain scalar type made gcc check the use.
The variable wasn't actually used uninitialized, but gcc apparently
failed to notice that the conditional around the use was exactly the
same as the conditional around the initialization of that variable.
Add an unnecessary initialization just to shut up the compiler.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull timer type cleanups from Thomas Gleixner:
"This series does a tree wide cleanup of types related to
timers/timekeeping.
- Get rid of cycles_t and use a plain u64. The type is not really
helpful and caused more confusion than clarity
- Get rid of the ktime union. The union has become useless as we use
the scalar nanoseconds storage unconditionally now. The 32bit
timespec alike storage got removed due to the Y2038 limitations
some time ago.
That leaves the odd union access around for no reason. Clean it up.
Both changes have been done with coccinelle and a small amount of
manual mopping up"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
ktime: Get rid of ktime_equal()
ktime: Cleanup ktime_set() usage
ktime: Get rid of the union
clocksource: Use a plain u64 instead of cycle_t
Pull SMP hotplug notifier removal from Thomas Gleixner:
"This is the final cleanup of the hotplug notifier infrastructure. The
series has been reintgrated in the last two days because there came a
new driver using the old infrastructure via the SCSI tree.
Summary:
- convert the last leftover drivers utilizing notifiers
- fixup for a completely broken hotplug user
- prevent setup of already used states
- removal of the notifiers
- treewide cleanup of hotplug state names
- consolidation of state space
There is a sphinx based documentation pending, but that needs review
from the documentation folks"
* 'smp-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/armada-xp: Consolidate hotplug state space
irqchip/gic: Consolidate hotplug state space
coresight/etm3/4x: Consolidate hotplug state space
cpu/hotplug: Cleanup state names
cpu/hotplug: Remove obsolete cpu hotplug register/unregister functions
staging/lustre/libcfs: Convert to hotplug state machine
scsi/bnx2i: Convert to hotplug state machine
scsi/bnx2fc: Convert to hotplug state machine
cpu/hotplug: Prevent overwriting of callbacks
x86/msr: Remove bogus cleanup from the error path
bus: arm-ccn: Prevent hotplug callback leak
perf/x86/intel/cstate: Prevent hotplug callback leak
ARM/imx/mmcd: Fix broken cpu hotplug handling
scsi: qedi: Convert to hotplug state machine
Pull turbostat updates from Len Brown.
* 'turbostat' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
tools/power turbostat: remove obsolete -M, -m, -C, -c options
tools/power turbostat: Make extensible via the --add parameter
tools/power turbostat: Denverton uses a 25 MHz crystal, not 19.2 MHz
tools/power turbostat: line up headers when -M is used
tools/power turbostat: fix SKX PKG_CSTATE_LIMIT decoding
tools/power turbostat: Support Knights Mill (KNM)
tools/power turbostat: Display HWP OOB status
tools/power turbostat: fix Denverton BCLK
tools/power turbostat: use intel-family.h model strings
tools/power/turbostat: Add Denverton RAPL support
tools/power/turbostat: Add Denverton support
tools/power/turbostat: split core MSR support into status + limit
tools/power turbostat: fix error case overflow read of slm_freq_table[]
tools/power turbostat: Allocate correct amount of fd and irq entries
tools/power turbostat: switch to tab delimited output
tools/power turbostat: Gracefully handle ACPI S3
tools/power turbostat: tidy up output on Joule counter overflow
Add a new page flag, PageWaiters, to indicate the page waitqueue has
tasks waiting. This can be tested rather than testing waitqueue_active
which requires another cacheline load.
This bit is always set when the page has tasks on page_waitqueue(page),
and is set and cleared under the waitqueue lock. It may be set when
there are no tasks on the waitqueue, which will cause a harmless extra
wakeup check that will clears the bit.
The generic bit-waitqueue infrastructure is no longer used for pages.
Instead, waitqueues are used directly with a custom key type. The
generic code was not flexible enough to have PageWaiters manipulation
under the waitqueue lock (which simplifies concurrency).
This improves the performance of page lock intensive microbenchmarks by
2-3%.
Putting two bits in the same word opens the opportunity to remove the
memory barrier between clearing the lock bit and testing the waiters
bit, after some work on the arch primitives (e.g., ensuring memory
operand widths match and cover both bits).
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Bob Peterson <rpeterso@redhat.com>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Andrew Lutomirski <luto@kernel.org>
Cc: Andreas Gruenbacher <agruenba@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A page is not added to the swap cache without being swap backed,
so PageSwapBacked mappings can use PG_owner_priv_1 for PageSwapCache.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Acked-by: Hugh Dickins <hughd@google.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Bob Peterson <rpeterso@redhat.com>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Andrew Lutomirski <luto@kernel.org>
Cc: Andreas Gruenbacher <agruenba@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
No point in going through loops and hoops instead of just comparing the
values.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
ktime_set(S,N) was required for the timespec storage type and is still
useful for situations where a Seconds and Nanoseconds part of a time value
needs to be converted. For anything where the Seconds argument is 0, this
is pointless and can be replaced with a simple assignment.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
ktime is a union because the initial implementation stored the time in
scalar nanoseconds on 64 bit machine and in a endianess optimized timespec
variant for 32bit machines. The Y2038 cleanup removed the timespec variant
and switched everything to scalar nanoseconds. The union remained, but
become completely pointless.
Get rid of the union and just keep ktime_t as simple typedef of type s64.
The conversion was done with coccinelle and some manual mopping up.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
There is no point in having an extra type for extra confusion. u64 is
unambiguous.
Conversion was done with the following coccinelle script:
@rem@
@@
-typedef u64 cycle_t;
@fix@
typedef cycle_t;
@@
-cycle_t
+u64
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: John Stultz <john.stultz@linaro.org>
The mpic is either the main interrupt controller or is cascaded behind a
GIC. The mpic is single instance and the modes are mutually exclusive, so
there is no reason to have seperate cpu hotplug states.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Link: http://lkml.kernel.org/r/20161221192112.333161745@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Even if both drivers are compiled in only one instance can run on a given
system depending on the available GIC version.
So having seperate hotplug states for them is pointless.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Link: http://lkml.kernel.org/r/20161221192112.252416267@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Even if both drivers are compiled in only one instance can run on a given
system depending on the available tracer cell.
So having seperate hotplug states for them is pointless.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: http://lkml.kernel.org/r/20161221192112.162765484@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When the state names got added a script was used to add the extra argument
to the calls. The script basically converted the state constant to a
string, but the cleanup to convert these strings into meaningful ones did
not happen.
Replace all the useless strings with 'subsys/xxx/yyy:state' strings which
are used in all the other places already.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Link: http://lkml.kernel.org/r/20161221192112.085444152@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
hotcpu_notifier(), cpu_notifier(), __hotcpu_notifier(), __cpu_notifier(),
register_hotcpu_notifier(), register_cpu_notifier(),
__register_hotcpu_notifier(), __register_cpu_notifier(),
unregister_hotcpu_notifier(), unregister_cpu_notifier(),
__unregister_hotcpu_notifier(), __unregister_cpu_notifier()
are unused now. Remove them and all related code.
Remove also the now pointless cpu notifier error injection mechanism. The
states can be executed step by step and error rollback is the same as cpu
down, so any state transition can be tested w/o requiring the notifier
error injection.
Some CPU hotplug states are kept as they are (ab)used for hotplug state
tracking.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20161221192112.005642358@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Install the callbacks via the state machine. No functional change.
This is the minimal fixup so we can remove the hotplug notifier mess
completely.
The real rework of this driver to use work queues is still stuck in
review/testing on the SCSI mailing list.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: "James E.J. Bottomley" <jejb@linux.vnet.ibm.com>
Cc: linux-scsi@vger.kernel.org
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Chad Dupuis <chad.dupuis@qlogic.com>
Cc: QLogic-Storage-Upstream@qlogic.com
Cc: Johannes Thumshirn <jth@kernel.org>
Cc: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/20161221192111.836895753@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Install the callbacks via the state machine. No functional change.
This is the minimal fixup so we can remove the hotplug notifier mess
completely.
The real rework of this driver to use work queues is still stuck in
review/testing on the SCSI mailing list.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: "James E.J. Bottomley" <jejb@linux.vnet.ibm.com>
Cc: linux-scsi@vger.kernel.org
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Chad Dupuis <chad.dupuis@qlogic.com>
Cc: QLogic-Storage-Upstream@qlogic.com
Cc: Johannes Thumshirn <jth@kernel.org>
Cc: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/20161221192111.757309869@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Developers manage to overwrite states blindly without thought. That's fatal
and hard to debug. Add sanity checks to make it fail.
This requries to restructure the code so that the dynamic state allocation
happens in the same lock protected section as the actual store. Otherwise
the previous assignment of 'Reserved' to the name field would trigger the
overwrite check.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Link: http://lkml.kernel.org/r/20161221192111.675234535@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The error cleanup which is invoked when the hotplug state setup failed
tries to remove the failed state, which is broken.
Fixes: 8fba38c937 ("x86/msr: Convert to hotplug state machine")
Reported-by: kernel test robot <fengguang.wu@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
In case the driver registration fails, the hotplug callback is leaked.
Not fatal, because it's never invoked as there are no instances registered,
but wrong nevertheless.
Fixes: fdc15a36d8 ("bus/arm-ccn: Convert to hotplug statemachine")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Will Deacon <will.deacon@arm.com>
If the pmu registration fails the registered hotplug callbacks are not
removed. Wrong in any case, but fatal in case of a modular driver.
Replace the nonsensical state names with proper ones while at it.
Fixes: 77c34ef1c3 ("perf/x86/intel/cstate: Convert Intel CSTATE to hotplug state machine")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: stable@vger.kernel.org
The cpu hotplug support of this perf driver is broken in several ways:
1) It adds a instance before setting up the state.
2) The state for the instance is different from the state of the
callback. It's just a randomly chosen state.
3) The instance registration is not error checked so nobody noticed that
the call can never succeed.
4) The state for the multi install callbacks is chosen randomly and
overwrites existing state. This is now prevented by the core code so the
call is guaranteed to fail.
5) The error exit path in the init function leaves the instance registered
and then frees the memory which contains the enqueued hlist node.
6) The remove function is removing the state and not the instance.
Fix it by:
- Setting up the state before adding instances. Use a dynamically allocated
state for it.
- Installing instances after the state has been set up
- Removing the instance in the error path before freeing memory
- Removing the instance not the state in the driver remove callback
While at is use raw_cpu_processor_id(), because cpu_processor_id() cannot
be used in preemptible context, and set the driver data after successful
registration of the pmu.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Frank Li <frank.li@nxp.com>
Cc: Zhengyu Shen <zhengyu.shen@nxp.com>
Link: http://lkml.kernel.org/r/20161221192111.596204211@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The CPU hotplug code is a trainwreck. It leaks a notifier in case of driver
registration error and the per cpu loop is racy against cpu hotplug. Aside
of that the driver should have been written and merged with the new state
machine interfaces in the first place.
Mop up the mess and Convert it to the hotplug state machine.
Signed-off-by: Thomas Grumpy Gleixner <tglx@linutronix.de>
Cc: Nilesh Javali <nilesh.javali@cavium.com>
Cc: Adheer Chandravanshi <adheer.chandravanshi@qlogic.com>
Cc: Chad Dupuis <chad.dupuis@cavium.com>
Cc: Saurav Kashyap <saurav.kashyap@cavium.com>
Cc: Arun Easi <arun.easi@cavium.com>
Cc: Manish Rangankar <manish.rangankar@cavium.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
The new --add option has replaced the -M, -m, -C, -c options
Eg.
-M 0x10 is now --add msr0x10,raw
-m 0x10 is now --add msr0x10,raw,u32
-C 0x10 is now --add msr0x10,delta
-c 0x10 is now --add msr0x10,delta,u32
The --add option can be repeated to add any number of counters,
while the previous options were limited to adding one of each type.
In addition, the --add option can accept a column label,
and can also display a counter as a percentage of elapsed cycles.
Eg. --add msr0x3fe,core,percent,MY_CC3
Signed-off-by: Len Brown <len.brown@intel.com>
Create the "--add" parameter. This can be used to teach an existing
turbostat binary about any number of any type of counter.
turbostat(8) details the syntax for --add.
Signed-off-by: Len Brown <len.brown@intel.com>
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull cifs fixes from Steve French:
"This ncludes various cifs/smb3 bug fixes, mostly for stable as well.
In the next week I expect that Germano will have some reconnection
fixes, and also I expect to have the remaining pieces of the snapshot
enablement and SMB3 ACLs, but wanted to get this set of bug fixes in"
* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
cifs_get_root shouldn't use path with tree name
Fix default behaviour for empty domains and add domainauto option
cifs: use %16phN for formatting md5 sum
cifs: Fix smbencrypt() to stop pointing a scatterlist at the stack
CIFS: Fix a possible double locking of mutex during reconnect
CIFS: Fix a possible memory corruption during reconnect
CIFS: Fix a possible memory corruption in push locks
CIFS: Fix missing nls unload in smb2_reconnect()
CIFS: Decrease verbosity of ioctl call
SMB3: parsing for new snapshot timestamp mount parm
New driver for Add Loongson1 SoC.
Minor cleanup and fixes in various drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=iGOO
-----END PGP SIGNATURE-----
Merge tag 'watchdog-for-linus-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull watchdog updates from Wim Van Sebroeck and Guenter Roeck:
- new driver for Add Loongson1 SoC
- minor cleanup and fixes in various drivers
* tag 'watchdog-for-linus-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
watchdog: it87_wdt: add IT8620E ID
watchdog: mpc8xxx: Remove unneeded linux/miscdevice.h include
watchdog: octeon: Remove unneeded linux/miscdevice.h include
watchdog: bcm2835_wdt: set WDOG_HW_RUNNING bit when appropriate
watchdog: loongson1: Add Loongson1 SoC watchdog driver
watchdog: cpwd: remove memory allocate failure message
watchdog: da9062/61: watchdog driver
intel-mid_wdt: Error code is just an integer
intel-mid_wdt: make sure watchdog is not running at startup
watchdog: mei_wdt: request stop on reboot to prevent false positive event
watchdog: hpwdt: changed maintainer information
watchdog: jz4740: Fix modular build
watchdog: qcom: fix kernel panic due to external abort on non-linefetch
watchdog: davinci: add support for deferred probing
watchdog: meson: Remove unneeded platform MODULE_ALIAS
watchdog: Standardize leading tabs and spaces in Kconfig file
watchdog: max77620_wdt: fix module autoload
watchdog: bcm7038_wdt: fix module autoload
and correcting a free_irq inconsistency. It adds Intel SKX support.
Finally, it changes the AMD NTB maintainer, and fixes some bugs present
there.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=F0Rd
-----END PGP SIGNATURE-----
Merge tag 'ntb-4.10' of git://github.com/jonmason/ntb
Pull NTB update from Jon Mason:
- NTB bug fixes for removing an unnecessary call to ntb_peer_spad_read,
and correcting a free_irq inconsistency
- add Intel SKX support
- change the AMD NTB maintainer, and fix some bugs present there
* tag 'ntb-4.10' of git://github.com/jonmason/ntb:
ntb_transport: Remove unnecessary call to ntb_peer_spad_read
NTB: Fix 'request_irq()' and 'free_irq()' inconsistancy
ntb: fix SKX NTB config space size register offsets
NTB: correct ntb_peer_spad_read for case when callback is not supplied.
MAINTAINERS: Change in maintainer for AMD NTB
ntb_transport: Limit memory windows based on available, scratchpads
NTB: Register and offset values fix for memory window
NTB: add support for hotplug feature
ntb: Adding Skylake Xeon NTB support
Pull x86 fixes from Ingo Molnar:
"There's a number of fixes:
- a round of fixes for CPUID-less legacy CPUs
- a number of microcode loader fixes
- i8042 detection robustization fixes
- stack dump/unwinder fixes
- x86 SoC platform driver fixes
- a GCC 7 warning fix
- virtualization related fixes"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
Revert "x86/unwind: Detect bad stack return address"
x86/paravirt: Mark unused patch_default label
x86/microcode/AMD: Reload proper initrd start address
x86/platform/intel/quark: Add printf attribute to imr_self_test_result()
x86/platform/intel-mid: Switch MPU3050 driver to IIO
x86/alternatives: Do not use sync_core() to serialize I$
x86/topology: Document cpu_llc_id
x86/hyperv: Handle unknown NMIs on one CPU when unknown_nmi_panic
x86/asm: Rewrite sync_core() to use IRET-to-self
x86/microcode/intel: Replace sync_core() with native_cpuid()
Revert "x86/boot: Fail the boot if !M486 and CPUID is missing"
x86/asm/32: Make sync_core() handle missing CPUID on all 32-bit kernels
x86/cpu: Probe CPUID leaf 6 even when cpuid_level == 6
x86/tools: Fix gcc-7 warning in relocs.c
x86/unwind: Dump stack data on warnings
x86/unwind: Adjust last frame check for aligned function stacks
x86/init: Fix a couple of comment typos
x86/init: Remove i8042_detect() from platform ops
Input: i8042 - Trust firmware a bit more when probing on X86
x86/init: Add i8042 state to the platform data
...
Pull perf fixes from Ingo Molnar:
"On the kernel side there's two x86 PMU driver fixes and a uprobes fix,
plus on the tooling side there's a number of fixes and some late
updates"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (36 commits)
perf sched timehist: Fix invalid period calculation
perf sched timehist: Remove hardcoded 'comm_width' check at print_summary
perf sched timehist: Enlarge default 'comm_width'
perf sched timehist: Honour 'comm_width' when aligning the headers
perf/x86: Fix overlap counter scheduling bug
perf/x86/pebs: Fix handling of PEBS buffer overflows
samples/bpf: Move open_raw_sock to separate header
samples/bpf: Remove perf_event_open() declaration
samples/bpf: Be consistent with bpf_load_program bpf_insn parameter
tools lib bpf: Add bpf_prog_{attach,detach}
samples/bpf: Switch over to libbpf
perf diff: Do not overwrite valid build id
perf annotate: Don't throw error for zero length symbols
perf bench futex: Fix lock-pi help string
perf trace: Check if MAP_32BIT is defined (again)
samples/bpf: Make perf_event_read() static
uprobes: Fix uprobes on MIPS, allow for a cache flush after ixol breakpoint creation
samples/bpf: Make samples more libbpf-centric
tools lib bpf: Add flags to bpf_create_map()
tools lib bpf: use __u32 from linux/types.h
...
Pull irq fix from Ingo Molnar:
"A build warning fix with certain .config's"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/st: Mark st_irq_syscfg_resume() __maybe_unused
The results were previously ignored, anyway.
Signed-off-by: Steve Wahl <Steve.Wahl@dell.com>
Fixes: e26a5843f7
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
'request_irq()' and 'free_irq()' should have the same 'dev_id'.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
The offsets for the SZ registers are wrong. Updated.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Reported-by: Sandeep Mann <sandeep@purestorage.com>
Tested-by: Zachary Ross <zacharyx.ross@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Correct ntb_peer_spad_read for case when callback is not supplied
Signed-off-by: Steve Wahl <Steve.Wahl@dell.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
I would like to take maintainership for AMD NTB
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Xiangliang Yu <Xiangliang.Yu@amd.com>
Acked-by: Xiangliang Yu <Xiangliang.Yu@amd.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
When the underlying NTB H/W driver advertises more memory windows
than the number of scratchpads available to setup MW's, it is likely
that we may end up filling the remaining memory windows with garbage.
So to avoid that, lets limit the memory windows that transport driver
can setup based on the available scratchpads.
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Due to incorrect limit and translation register values, NTB link was
going down when the memory window was setup. Made appropriate changes
as per spec.
Fix limit register values for BAR1, which was overlapping
with the BAR23 address.
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
AMD NTB support hotplug under B2B mode. NTB will trigger link
up/down interrupt event when doing plug add/remove, this patch
implements the two interrupt event to support B2B hotplug function.
Signed-off-by: Xiangliang Yu <Xiangliang.Yu@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
The Skylake Xeon NTB hardware has made some changes to the register name,
offset, and the way doorbells work. Adding driver support for the new
hardware.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
