Commit Graph

155717 Commits

Author SHA1 Message Date
Michael Buesch
f62ae6cd88 b43: Fix unaligned 32bit SHM-shared access
This fixes unaligned 32bit SHM-shared read/write access.
The low and high 16 bits were swapped.
It also adds a testcase for this to the chipaccess validation.

(Thanks to Albert Herranz for tracking down this bug.)

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-04 16:44:21 -04:00
Andrey Yurovsky
88d89526a6 libertas: check valid bits in SPI bus mode reg
The SPI driver writes to the bus mode register and performs a sanity
check by reading back what we wrote, however only the lower four bits of
that register are defined.  In some cases, the device side seems to set
the higher bits, causing us to fail the sanity check unnecessarily.
Check only the lower four bits instead.

Thanks to John Goyette from Schick Technologies for pointing out the
problem.

Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-04 16:44:21 -04:00
Maxim Levitsky
d1c5091f23 mac80211: Increase timeouts for station polling
Do a probe request every 30 seconds, and wait for probe response,
half a second This should lower the traffic that card sends, thus save
power Wainting longer for response makes probe more robust against
'slow' access points

Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Tested-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-04 16:44:20 -04:00
Maxim Levitsky
a43abf2939 mac80211: Retry probe request few times
Retry 5 times  (chosen arbitary ), before assuming
that station is out of range.

Fixes frequent disassociations while connected to weak,
and sometimes even strong access points.

Signed-off-by: Maxim Levitky <maximlevitsky@gmail.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-04 16:44:20 -04:00
Johannes Berg
75e6c3b72b cfg80211: lower dynamic PS timeout to 100ms
The default of 500ms is pretty high, and leads
to the device being awake at least 50% of the
time under such light traffic conditions as a
simple 1 second interval ping. Reduce to just
100ms -- it should have a similar effect while
providing a better sleep time.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-04 16:44:20 -04:00
Luis R. Rodriguez
97cad51e19 iwlwifi: remove usage of orig_flags
This is a private flag, internal to cfg80211. cfg80211
will set orig_* stuff internally upon wiphy registration,
drivers do not need to muck with it.

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-04 16:44:20 -04:00
Luis R. Rodriguez
8b19e6ca3b cfg80211: enable country IE support to all cfg80211 drivers
Since the bss is always set now once we are connected, if the
bss has its own information element we refer to it and pass that
instead of relying on mac80211's parsing.

Now all cfg80211 drivers get country IE support, automatically and
we reduce the call overhead that we had on mac80211 which called this
upon every beacon and instead now call this only upon a successfull
connection by a STA on cfg80211.

Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-04 16:44:19 -04:00
Luis R. Rodriguez
abc7381bcc cfg80211: decouple regulatory variables from cfg80211_mutex
We change regulatory code to be protected by its own regulatory
mutex and alleviate cfg80211_mutex to only be used to protect
cfg80211_rdev_list, the registered device list.

By doing this we will be able to work on regulatory core components
without having to have hog up the cfg80211_mutex. An example here is
we no longer need to use the cfg80211_mutex during driver specific
wiphy_apply_custom_regulatory(). We also no longer need it for the
the country IE regulatory hint; by doing so we end up curing this
new lockdep warning:

=======================================================
[ INFO: possible circular locking dependency detected ]
2.6.31-rc4-wl #12
-------------------------------------------------------
phy1/1709 is trying to acquire lock:
 (cfg80211_mutex){+.+.+.}, at: [<ffffffffa00af852>] regulatory_hint_11d+0x32/0x3f0 [cfg80211]

but task is already holding lock:
 (&ifmgd->mtx){+.+.+.}, at: [<ffffffffa0144228>] ieee80211_sta_work+0x108/0x10f0 [mac80211]

which lock already depends on the new lock.

the existing dependency chain (in reverse order) is:

-> #3 (&ifmgd->mtx){+.+.+.}:
       [<ffffffff810857b6>] __lock_acquire+0xd76/0x12b0
       [<ffffffff81085dd3>] lock_acquire+0xe3/0x120
       [<ffffffff814eeae4>] mutex_lock_nested+0x44/0x350
       [<ffffffffa0141bb8>] ieee80211_mgd_auth+0x108/0x1f0 [mac80211]
       [<ffffffffa0148563>] ieee80211_auth+0x13/0x20 [mac80211]
       [<ffffffffa00bc3a1>] __cfg80211_mlme_auth+0x1b1/0x2a0 [cfg80211]
       [<ffffffffa00bc516>] cfg80211_mlme_auth+0x86/0xc0 [cfg80211]
       [<ffffffffa00b368d>] nl80211_authenticate+0x21d/0x230 [cfg80211]
       [<ffffffff81416ba6>] genl_rcv_msg+0x1b6/0x1f0
       [<ffffffff81415c39>] netlink_rcv_skb+0x89/0xb0
       [<ffffffff814169d9>] genl_rcv+0x29/0x40
       [<ffffffff8141591d>] netlink_unicast+0x29d/0x2b0
       [<ffffffff81416514>] netlink_sendmsg+0x214/0x300
       [<ffffffff813e4407>] sock_sendmsg+0x107/0x130
       [<ffffffff813e45b9>] sys_sendmsg+0x189/0x320
       [<ffffffff81011f82>] system_call_fastpath+0x16/0x1b
       [<ffffffffffffffff>] 0xffffffffffffffff

-> #2 (&wdev->mtx){+.+.+.}:
       [<ffffffff810857b6>] __lock_acquire+0xd76/0x12b0
       [<ffffffff81085dd3>] lock_acquire+0xe3/0x120
       [<ffffffff814eeae4>] mutex_lock_nested+0x44/0x350
       [<ffffffffa00ab304>] cfg80211_netdev_notifier_call+0x1a4/0x390 [cfg80211]
       [<ffffffff814f3dff>] notifier_call_chain+0x3f/0x80
       [<ffffffff81075a91>] raw_notifier_call_chain+0x11/0x20
       [<ffffffff813f665a>] dev_open+0x10a/0x120
       [<ffffffff813f59bd>] dev_change_flags+0x9d/0x1e0
       [<ffffffff8144eb6e>] devinet_ioctl+0x6fe/0x760
       [<ffffffff81450204>] inet_ioctl+0x94/0xc0
       [<ffffffff813e25fa>] sock_ioctl+0x6a/0x290
       [<ffffffff8111e911>] vfs_ioctl+0x31/0xa0
       [<ffffffff8111ea9a>] do_vfs_ioctl+0x8a/0x5c0
       [<ffffffff8111f069>] sys_ioctl+0x99/0xa0
       [<ffffffff81011f82>] system_call_fastpath+0x16/0x1b
       [<ffffffffffffffff>] 0xffffffffffffffff

-> #1 (&rdev->mtx){+.+.+.}:
       [<ffffffff810857b6>] __lock_acquire+0xd76/0x12b0
       [<ffffffff81085dd3>] lock_acquire+0xe3/0x120
       [<ffffffff814eeae4>] mutex_lock_nested+0x44/0x350
       [<ffffffffa00ac4d0>] cfg80211_get_dev_from_ifindex+0x60/0x90 [cfg80211]
       [<ffffffffa00b21ff>] get_rdev_dev_by_info_ifindex+0x6f/0xa0 [cfg80211]
       [<ffffffffa00b51eb>] nl80211_set_interface+0x3b/0x260 [cfg80211]
       [<ffffffff81416ba6>] genl_rcv_msg+0x1b6/0x1f0
       [<ffffffff81415c39>] netlink_rcv_skb+0x89/0xb0
       [<ffffffff814169d9>] genl_rcv+0x29/0x40
       [<ffffffff8141591d>] netlink_unicast+0x29d/0x2b0
       [<ffffffff81416514>] netlink_sendmsg+0x214/0x300
       [<ffffffff813e4407>] sock_sendmsg+0x107/0x130
       [<ffffffff813e45b9>] sys_sendmsg+0x189/0x320
       [<ffffffff81011f82>] system_call_fastpath+0x16/0x1b
       [<ffffffffffffffff>] 0xffffffffffffffff

other info that might help us debug this:

3 locks held by phy1/1709:
 #0:  ((wiphy_name(local->hw.wiphy))){+.+.+.}, at: [<ffffffff8106b45d>] worker_thread+0x19d/0x340
 #1:  (&ifmgd->work){+.+.+.}, at: [<ffffffff8106b45d>] worker_thread+0x19d/0x340
 #2:  (&ifmgd->mtx){+.+.+.}, at: [<ffffffffa0144228>] ieee80211_sta_work+0x108/0x10f0 [mac80211]

Reported-by: Reinette Chatre <reinette.chatre@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-04 16:44:18 -04:00
Luis R. Rodriguez
4b44c8bc4d cfg80211: do not iterate over rdev list on country IE hint
Simplify the country IE hint code by just bailing out if
a previous country IE has been issued. We currently just trust
the first AP we connect to on any card. The idea was to perform
conflict resolution within this routine but since we can no longer
iterate over the registered device list here we leave conflict
resolution to be dealt with at a later time on the workqueue.

This code has no functional changes other than saving us an
interation over the registered device list when a second card
is connected, or you unplug and connect the same one, and a
country IE is received. This would have been done upon every
beacon received.

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-04 16:44:18 -04:00
Luis R. Rodriguez
9828b0170e cfg80211: use goto out on country IE reg hint failure
This has no functional changes.

Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-04 16:44:18 -04:00
Johannes Berg
056508dcb6 mac80211: fix powersave
Some of the recent MLME rework I did broke powersave
because the ps_sdata isn't assigned at the right time,
and the work item wasn't removed from the list before
calling ieee80211_recalc_ps(). To be more specific,
this broke the case where you'd enabled PS before
associating, either automatically or with iwconfig.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-04 16:44:18 -04:00
Jussi Kivilinna
b7cfc5b35e rndis_wlan: rework key handling
Organize key data in private structure better and store WPA keys, so
they can be restored as WEP keys.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-04 16:44:17 -04:00
Jussi Kivilinna
9d40934e5e rndis_wlan: add missing padding to struct rndis_80211_remove_key
OID_802_11_REMOVE_KEY failed with invalid length error, add missing padding to
structure fix this.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-04 16:44:17 -04:00
Jussi Kivilinna
030645aceb rndis_wlan: handle 802.11 indications from device
Add handling for 802.11 specific rndis indications.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-04 16:44:17 -04:00
Jussi Kivilinna
2a4901bcbe rndis_host: allow rndis_wlan to see all indications
Allow rndis_wlan to see all indications. Currently rndis_host lets rndis_wlan to
know about link state changes only, but there is whole set of other
802.11-specific indications that rndis_wlan should handle properly. So rename
link_change() to indication() and convert rndis_wlan to use it.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-04 16:44:17 -04:00
Jussi Kivilinna
27b7b5c131 rndis_wlan: add rndis_set/query_oid debugging
Add better debugging for failed OID queries.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-04 16:44:16 -04:00
Jussi Kivilinna
e5a11a822e rndis_wlan: set current packet filter to zero on stop
Set current packet filter to zero to block receiving data packets from
device.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-04 16:44:16 -04:00
Jussi Kivilinna
7eaab7086c rndis_wlan: reset device and restore multicast list on rndis_wlan_reset()
Reset device properly with RNDIS_MSG_RESET in rndis_wlan_reset() and restore
multicast list afterwards.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-04 16:44:16 -04:00
Jussi Kivilinna
005ba2f17e rndis_wlan: clear cfg80211 scan on rndis_wlan_stop()
Scanning gets stuck if device is stopped when scan is active. Fix by
clearing/aborting cfg80211 scan on rndis_wlan_stop().

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-04 16:44:16 -04:00
Jussi Kivilinna
110736de93 rndis_wlan: stop workers on rndis_wlan_stop() and restore on rndis_wlan_reset()
Driver doesn't need to poll statistics/link status when stopped.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-04 16:44:15 -04:00
Jussi Kivilinna
1487cd5e76 usbnet: allow "minidriver" to prevent urb unlinking on usbnet_stop
rndis_wlan devices freeze after running usbnet_stop several times. It appears
that firmware freezes in state where it does not respond to any RNDIS commands
and device have to be physically unplugged/replugged. This patch lets
minidrivers to disable unlink_urbs on usbnet_stop through new info flag.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-04 16:44:15 -04:00
Johannes Berg
e40cbdac06 cfg80211: fix NETDEV_UNREGISTER notifier
It's possible to get the NETDEV_UNREGISTER callback multiple
times (see net/core/dev.c:netdev_wait_allrefs) and this will
completely mess up our cleanup code. To avoid that, clean up
only when the interface is still on the wiphy interface list
from which it's removed on the first NETDEV_UNREGISTER call.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-04 16:44:15 -04:00
Johannes Berg
e46ab7f088 iwlwifi: don't export symbols not needed in other modules
Even with the split into iwlcore/agn/3945 not all symbols
that cross file boundaries are needed in other modules, a
few are only used within iwlcore, for example.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-04 16:44:15 -04:00
Luis R. Rodriguez
42935ecaf4 mac80211: redefine usage of the mac80211 workqueue
The mac80211 workqueue exists to enable mac80211 and drivers
to queue their own work on a single threaded workqueue. mac80211
takes care to flush the workqueue during suspend but we never
really had requirements on drivers for how they should use
the workqueue in consideration for suspend.

We extend mac80211 to document how the mac80211 workqueue should
be used, how it should not be used and finally move raw access to
the workqueue to mac80211 only. Drivers and mac80211 use helpers
to queue work onto the mac80211 workqueue:

  * ieee80211_queue_work()
  * ieee80211_queue_delayed_work()

These helpers will now warn if mac80211 already completed its
suspend cycle and someone is trying to queue work. mac80211
flushes the mac80211 workqueue prior to suspend a few times,
but we haven't taken the care to ensure drivers won't add more
work after suspend. To help with this we add a warning when
someone tries to add work and mac80211 already completed the
suspend cycle.

Drivers should ensure they cancel any work or delayed work
in the mac80211 stop() callback.

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-04 16:44:14 -04:00
Luis R. Rodriguez
64344d7822 at76c50x-usb: remove unneeded flush_workqueue() at usb disconnect
This driver only uses the mac80211 workqueue and mac80211 requires us to
cancel all work at driver stop. Since we now have the cancels in the right
places at stop() we really don't need to flush the mac80211 workqueue so
remove it.

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-04 16:43:27 -04:00
Bob Copeland
8784d2ee92 ath5k: fix CAB queue operation
We need to process tx descriptors for all queues (currently main tx
queue and cabq) which may have triggered the TX completion interrupt.
Otherwise, the queues can get stuck after sending a few frames.

Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-04 16:43:27 -04:00
Holger Schurig
7e2ce646fc orinoco: enable cfg80211 "set_channel" operation
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-04 16:43:26 -04:00
Luis R. Rodriguez
91b092d734 ar9170: remove EXPERIMENTAL marker
Cc: Christian Lamparter <chunkeey@web.de>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-04 16:43:26 -04:00
Larry Finger
18c6951091 b43: Work around mac80211 race condition
As shown in http://thread.gmane.org/gmane.linux.kernel.wireless.general/36497,
mac80211 has a bug that allows a call to the TX routine after the queues have
been stopped. This situation will only occur under extreme stress. Although
b43 does not crash when this condition occurs, it does generate a WARN_ON and
also logs a queue overrun message. This patch recognizes b43 is not at fault
and logs a message only when the most verbose debugging mode is enabled. In
the unlikely event that the queue is not stopped when the DMA queue becomes
full, then a warning is issued.

During testing of this patch with one output stream running repeated tcpperf
writes and a second running a flood ping, this routine was entered with
the DMA ring stopped about once per hour. The condition where the DMA queue is
full but the ring has not been stopped has never been seen by me.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-04 16:43:26 -04:00
Bob Copeland
ae6f53f25f ath5k: update PCU opmode whenever a new interface is added
Previously, we would store the operating mode at interface up time,
but only update the PCU registers when the next reset happened.
The result is that if beacon configuration (ops->bss_info_changed)
happens before ops->config, we will program the wrong things into
the timer registers.  Consequently, beacons won't work in AP mode
until after a reset (channel change, scan etc.).

This is fragile anyway so just program the opmode as soon as
mac80211 gives it to us.

Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-04 16:43:25 -04:00
Johannes Berg
57c9fff3d0 mac80211: fix sparse warnings/errors
sparse complains about a shadowed variable, which
we can just rename, and lots of stuff if the API
tracer is enabled, so kick out the tracer code in
a sparse run -- the macros just confuse it.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-04 16:43:25 -04:00
Vasanthakumar Thiagarajan
0b3acfa71a ath9k: Remove unused ath9k_hw_intrget()
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-04 16:43:24 -04:00
Vasanthakumar Thiagarajan
3fc0fbf407 ath9k: Maintain monotonicity of PER while going across different phy
Monotonicity of packet error rate should be kept when moving
from one phy to another (legacy to ht, ht single stream to dual,
etc). Current code skips updating per for other phys.

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-04 16:43:24 -04:00
Vasanthakumar Thiagarajan
42e8856092 ath9k: Update rate control for 11NA HT40 mode
Now the lowest rate in 11na ht40 mode is 13.5Mbps this shortens the
range when compared to 11na ht20 mode where the lowest rate is 6.5Mbps.
To improve the range, make 6.5Mbps as the lowest rate in 11na ht40 mode,
this improves the range by approximately 2dB. 11ng ht40 does not have
this issue as it also has basic rates (1, 2, 5.5 and 11).

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-04 16:43:24 -04:00
Johannes Berg
df7fc0f973 cfg80211: keep track of current_bss for userspace SME
When a userspace SME is active, we're currently not
keeping track of the BSS properly for reporting the
current link and for internal use. Additionally, it
looks like there is a possible BSS leak in that the
BSS never gets removed from auth_bsses[]. To fix it,
pass the BSS struct to __cfg80211_connect_result in
this case.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-04 16:43:24 -04:00
Bob Copeland
97af743207 mac80211: disable beacons before removing the associated interface
When downing interfaces, it's a good idea to tell the driver to
stop sending beacons; that way the driver doesn't need special
code in ops->remove_interface() when it should already handle the
case in bss_info_changed().

This fixes a potential crash with at least ath5k since the vif
pointer will be nullified while beacon interrupts are still active.

Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-04 16:43:23 -04:00
Ivo van Doorn
ad2f34b41f rt2x00: Fix build error when crypto support is disabled
When only rt2400pci or rt2500pci is compiled without any of the other
rt2x00 modules, then CONFIG_RT2X00_LIB_CRYPTO will not be enabled.

However rt2x00mac_set_tim() implemented within #ifdef CONFIG_RT2X00_LIB_CRYPTO
statements while the declaration is placed outside the definition. This results in linking
errors as reporte by Ken.

rt2x00_set_tim() has nothing to do with crypto, and thus should be moved outside
of the #ifdef statements.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-04 16:43:22 -04:00
Luis R. Rodriguez
33172899a9 rt2x00: move experimental on kconfig only to rt2800usb
These drivers have been around for a while, if there are issues
they should be reported. rt2800usb is still a bit flaky though.

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-04 16:43:22 -04:00
Luis R. Rodriguez
3e6404528c wireless: use menuconfig for WLAN_PRE80211 and WLAN_80211
This should make it very clear which are pre-802.11 or not

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-04 16:43:21 -04:00
Luis R. Rodriguez
75323fa3de ath5k: remove EXPERIMENTAL marker
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-04 16:43:21 -04:00
Luis R. Rodriguez
44b7dd6dde ath: use menuconfig to put ath stuff in its own page
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-04 16:43:21 -04:00
Luis R. Rodriguez
b820b3bcb0 ath: simplify kconfig dependency and add documentation
Make atheros wireless drivers visible when you select
"Atheros wirless drivers". Adds links to ath.ko page,
and Atheros drivers page on the wiki.

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-04 16:43:21 -04:00
Luis R. Rodriguez
d17734aee6 ath: depend on cfg80211
The ath.ko module itself depends on cfg80211

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-04 16:43:20 -04:00
Luis R. Rodriguez
dd21dcdc65 wext: remove extra return on wireless_nlevent_init()
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-04 16:43:20 -04:00
Luis R. Rodriguez
e351cfbf4e ar9170: remove unneeded flush_workqueue()
cancel_delayed_work_sync() and cancel_work_sync() are already being
used therefore already waiting for all pending work by the driver
to have been completed, no need to flush the mac80211 workqueue.

Cc: Christian Lamparter <chunkeey@web.de>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-04 16:43:20 -04:00
Luis R. Rodriguez
9ed21d3901 at76c50x-usb: cancel scan work at stop callback
This should fix suspend as mac80211 expects all work queued
to the mac80211 workqueue to be canceled at driver stop().

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-04 16:43:19 -04:00
Luis R. Rodriguez
ebc8ab17d6 ar76c50x-usb: cancel promisc work during mac80211 stop
We weren't ever cancelling this.

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-04 16:43:19 -04:00
Luis R. Rodriguez
c94dbff799 ath9k: move workqueue cancels to stop callback
We should be cancelling our work at the stop callback since
we are borrowing the mac80211 workqueue for our work. As it
stands mac80211 expects this for suspend purposes.

The ath9k specific virtual wiphy stuff need only be
cancelled only when the we have no secondary virtual wiphys.

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-04 16:43:19 -04:00
Luis R. Rodriguez
35c95ab9b5 ath9k: move cancel_delayed_work_sync() out of ath_deinit_leds()
We do this as we'll be moving the cancel elsewhere later.

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-04 16:43:18 -04:00
Luis R. Rodriguez
9851bad7a3 ath9k: re-order cancelling of work on mac80211 workqueue
ath9k uses the mac80211 workqueue for 4 different types of work:

 * Led blink work
 * TX hang monitoring work
 * internal wiphy schedular work
 * channel change work done for internal wiphy schedular

Since the internal wiphy schedular can end up kicking off some
channel channel change work we should first cancel the wiphy
schedular work and then the channel change work.

The TX hang work can be cancelled second since we're going down
anyway.

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-04 16:43:18 -04:00