This fixes dropping ownership of buffers in the driver's stop_streaming
callback, so buffers on the memory-to-memory video nodes are properly
released, also in case when the driver has a buffer only on one of the
queues (OUTPUT, CAPTURE) before the video node close.
The issue was being reported by videobuf2 with a following warning while
checking q->owned_by_drv_count:
[ 2498.310766] WARNING: CPU: 0 PID: 9358 at drivers/media/v4l2-core/videobuf2-core.c:1818 __vb2_queue_cancel+0xe8/0x14c
[ 2498.320258] Modules linked in:
[ 2498.323212] CPU: 0 PID: 9358 Comm: v4l2_decode Not tainted 4.7.0-rc4-next-20160627 #1210
[ 2498.331284] Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
[ 2498.331327] [<c010d738>] (unwind_backtrace) from [<c010a4b0>] (show_stack+0x10/0x14)
[ 2498.331344] [<c010a4b0>] (show_stack) from [<c031a4ac>] (dump_stack+0x74/0x94)
[ 2498.331358] [<c031a4ac>] (dump_stack) from [<c011a52c>] (__warn+0xd4/0x100)
[ 2498.331369] [<c011a52c>] (__warn) from [<c011a578>] (warn_slowpath_null+0x20/0x28)
[ 2498.331381] [<c011a578>] (warn_slowpath_null) from [<c04ed420>] (__vb2_queue_cancel+0xe8/0x14c)
[ 2498.331395] [<c04ed420>] (__vb2_queue_cancel) from [<c04ee10c>] (vb2_core_queue_release+0x18/0x38)
[ 2498.331406] [<c04ee10c>] (vb2_core_queue_release) from [<c04eab50>] (v4l2_m2m_ctx_release+0x1c/0x28)
[ 2498.331420] [<c04eab50>] (v4l2_m2m_ctx_release) from [<c04fe184>] (fimc_m2m_release+0x24/0x78)
[ 2498.331437] [<c04fe184>] (fimc_m2m_release) from [<c04d76c8>] (v4l2_release+0x34/0x74)
[ 2498.331455] [<c04d76c8>] (v4l2_release) from [<c01dc8d4>] (__fput+0x80/0x1bc)
[ 2498.331469] [<c01dc8d4>] (__fput) from [<c0132edc>] (task_work_run+0xc0/0xe4)
[ 2498.331482] [<c0132edc>] (task_work_run) from [<c011d460>] (do_exit+0x304/0xa24)
[ 2498.331493] [<c011d460>] (do_exit) from [<c011dccc>] (do_group_exit+0x3c/0xbc)
[ 2498.331505] [<c011dccc>] (do_group_exit) from [<c0126cac>] (get_signal+0x200/0x65c)
[ 2498.331517] [<c0126cac>] (get_signal) from [<c010e928>] (do_signal+0x84/0x3c4)
[ 2498.331532] [<c010e928>] (do_signal) from [<c010a0ec>] (do_work_pending+0xa4/0xb4)
[ 2498.331545] [<c010a0ec>] (do_work_pending) from [<c0107954>] (slow_work_pending+0xc/0x20)
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
According to the V4L2 documentation the driver and card fields should be
used to identify the driver and the device but the s5p-mfc driver fills
those field using the platform device name, which in turn is the name of
the device DT node.
So not only the filled information isn't correct but also the same values
are used in all the fields for both the encoder and decoder video devices.
Before this patch:
Driver Info (not using libv4l2):
Driver name : 11000000.codec
Card type : 11000000.codec
Bus info : platform:11000000.codec
Driver version: 4.7.0
Driver Info (not using libv4l2):
Driver name : 11000000.codec
Card type : 11000000.codec
Bus info : platform:11000000.codec
Driver version: 4.7.0
After this patch:
Driver Info (not using libv4l2):
Driver name : s5p-mfc
Card type : s5p-mfc-dec
Bus info : platform:11000000.codec
Driver version: 4.7.0
Driver Info (not using libv4l2):
Driver name : s5p-mfc
Card type : s5p-mfc-enc
Bus info : platform:11000000.codec
Driver version: 4.7.0
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The driver doesn't set the struct v4l2_capability bus_info field so the
v4l2-compliance tool reports the following errors for VIDIOC_QUERYCAP:
Required ioctls:
VIDIOC_QUERYCAP returned 0 (Success)
fail: v4l2-compliance.cpp(304): string empty
fail: v4l2-compliance.cpp(528): check_ustring(vcap.bus_info, sizeof(vcap.bus_info))
test VIDIOC_QUERYCAP: FAIL
This patch fixes by setting the field in VIDIOC_QUERYCAP ioctl handler:
Required ioctls:
VIDIOC_QUERYCAP returned 0 (Success)
test VIDIOC_QUERYCAP: OK
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The streaming field in struct vb2_queue is meant to be private and should
not be used by drivers directly, instead the vb2_is_streaming() function
should be used to check the videobuf2 queue streaming status.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The V4L2 documentation says that applications must call the VIDIOC_REQBUFS
ioctl to determine if a memory mapped, user pointer or DMABUF based I/O is
supported by the driver.
For example GStreamer does this by first calling VIDIOC_REQBUFS with count
zero for all the possible streaming I/O methods and then finally doing the
real VIDIOC_REQBUFS with count N using a known to be supported memory type.
But the driver prints an error on VIDIOC_REQBUFS if the memory type is not
supported which leads to the following errors that can confuse the users:
[ 178.704390] vidioc_reqbufs:575: Only V4L2_MEMORY_MMAP is supported
[ 178.704666] vidioc_reqbufs:575: Only V4L2_MEMORY_MMAP is supported
[ 178.714956] vidioc_reqbufs:575: Only V4L2_MEMORY_MMAP is supported
[ 178.715229] vidioc_reqbufs:575: Only V4L2_MEMORY_MMAP is supported
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The function comment has an obvious typo error, so fix it.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch fixes the error path in the driver probe, so in case of
any failure, the resources are not leaked.
Reported-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix Decoder and encoder video device double release in probe error path.
video_device_release(dev->vfd_dec) get called twice if decoder register
fails. Also, video_device_release(dev->vfd_enc) get called twice if encoder
register fails.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add video encoder node for MT8173
Signed-off-by: Tiffany Lin <tiffany.lin@mediatek.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add a DT binding documentation of Video Encoder for the
MT8173 SoC from Mediatek.
Signed-off-by: Tiffany Lin <tiffany.lin@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The VPU driver for hw video codec embedded in Mediatek's MT8173 SOCs.
It is able to handle video decoding/encoding of in a range of formats.
The driver provides with VPU firmware download, memory management and
the communication interface between CPU and VPU.
For VPU initialization, it will create virtual memory for CPU access and
IOMMU address for vcodec hw device access. When a decode/encode instance
opens a device node, vpu driver will download vpu firmware to the device.
A decode/encode instant will decode/encode a frame using VPU
interface to interrupt vpu to handle decoding/encoding jobs.
Signed-off-by: Andrew-CT Chen <andrew-ct.chen@mediatek.com>
Signed-off-by: Tiffany Lin <tiffany.lin@mediatek.com>
[hans.verkuil@cisco.com: drop unnecessary ARM || ARM64 dependency]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The formats are interleaved with the YUV packed and miscellaneous
formats, making the result confusing especially with the YUV444 format
being packed and not planar like YUV410 or YUV420. Move them to their
own group as the 2 planes or 3 non-contiguous planes formats to clarify
the header.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix rcar_vin_try_fmt's use of an inappropriate pad number when calling
the subdev set_fmt function - for the ADV7612, IDs should be non-zero.
Signed-off-by: William Towle <william.towle@codethink.co.uk>
Reviewed-by: Rob Taylor <rob.taylor@codethink.co.uk>
[ulrich.hecht+renesas@gmail.com: adapted to rcar-vin rewrite]
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add detection of source pad number for drivers aware of the media controller
API, so that rcar-vin can create device nodes to support modern drivers such
as adv7604.c (for HDMI on Lager) and the converted adv7180.c (for composite)
underneath.
Building rcar_vin gains a dependency on CONFIG_MEDIA_CONTROLLER, in
line with requirements for building the drivers associated with it.
Signed-off-by: William Towle <william.towle@codethink.co.uk>
Signed-off-by: Rob Taylor <rob.taylor@codethink.co.uk>
[ulrich.hecht+renesas@gmail.com: adapted to rcar-vin rewrite]
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The comments for the unlocked v4l2_ctrl_s_ctrl* functions were wrong (copy
and pasted from the locked variants). Fix this, since it is confusing.
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Memory allocated for maxiradio device is not deallocated when
the device is removed.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If *nplanes is not zero, it should use the requested size if valid
Signed-off-by: Helen Koike <helen.koike@collabora.co.uk>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The dv_timings_cap() and enum_dv_timings() pad operations take a pad
number as an input argument and return the DV timings capabilities and
list of supported DV timings for that pad.
Commit bd3e275f3e ("[media] media: i2c: adv7604: Use v4l2-dv-timings
helpers") broke this as it started ignoring the pad number, always
returning the information associated with the currently selected input.
Fix it.
Fixes: bd3e275f3e ("[media] media: i2c: adv7604: Use v4l2-dv-timings helpers")
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch adds V4L2 controls for Auto Exposure Control and Auto Gain
Control settings. These settings include low pass filter, update
frequency of these settings and the update interval for those units.
[Avoid forward declarations]
[Fix 80 columns limit violation]
[Rename controls to avoid underscores in names]
[Fix the AEC maximum shutter width on MT9V032]
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The power_on function of the driver resets the chip and sets the
CHIP_CONTROL register to 0. This switches the operating mode to slave.
The s_stream function sets the correct mode. But this caused problems on
a board where the camera chip is operated as master. The camera started
after a random amount of time streaming an image, I observed between 10
and 300 seconds.
The STRFM_OUT and STLN_OUT pins are not connected on this board which
may cause some issues in slave mode. I could not find any documentation
about this.
Keeping the chip in master mode after the reset helped to fix this
issue for me.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Since commit b42261078a ("regmap: i2c: fallback to SMBus if the adapter
does not support standard I2C"), regmap-i2c will check the
I2C_FUNC_SMBUS_[BYTE|WORD]_DATA functionality based on the regmap_config
setting if the adapter does not support standard I2C.
So remove the I2C_FUNC_SMBUS_WORD_DATA functionality check in the driver code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If the driver fails to reset the camera or to set up control handlers, it
has to power the camera back off.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This v4l2_subdev_internal_ops structure is never modified. All other
v4l2_subdev_internal_ops structures are declared as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The value is not used after the assignment.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Users won't know what to put in this module option if it isn't
described.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Audio hw params are shared across all DMA channels,
so if the user changes any of these while any DMA channel is
enabled, it will impact the enabled channels, potentially causing
serious instability issues.
This commit avoids such situation, by preventing any hw param
change (on any DMA channel) if any other DMA audio channel is capturing.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Currently, the driver has a fixed period size of 4096 bytes
(2048 frames). Since this hardware can configure the audio
capture size, this commit allows a period size range of [512-4096].
This is very useful to reduce the audio latency.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Now that we've introduced the dma_mode parameter to pick the
DMA operation, let's use it to also select the audio DMA
operation.
When dma_mode != memcpy, the driver will avoid using memcpy
in the audio capture path, and the DMA hardware operation
will act directly on the ALSA buffers.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Now that the driver has the infrastructure to support more
DMA modes, let's add the DMA scatter-gather mode.
In this mode, the device delivers sequential top-bottom
frames. The scatter-gather logic is based on staging's
tw686x-kh driver (by Krzysztof Ha?asa).
Tested-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Now that the driver has the infrastructure to support more
DMA modes, let's add the DMA contiguous interlaced frame mode.
In this mode, the DMA P and B buffers are programmed with
the user-provided buffers. When a P (or B) frame is ready,
a new buffer is dequeued into P (or B).
In addition to interlaced fields, the device can also be
programmed to deliver alternate fields. Only interlaced
mode is supported for now.
Tested-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Let's set the corner stone to support all the DMA modes
available on this device.
For stability reasons, the driver is currently setting DMA frame
mode, and using single DMA buffers to get the P and B buffers.
Each frame is then memcpy'ed into the user buffer.
However, other platforms might be interested in avoiding this
memcpy, or in taking advantage of the chip's DMA scatter-gather
capabilities.
To achieve this, this commit introduces a "dma_mode" module parameter,
and a tw686x_dma_ops struct. This will allow to define functions to
alloc/free DMA buffers, and to return the frames to userspace.
The memcpy-based method described above is named as dma_mode="memcpy".
Current alloc/free functions are renamed as tw686x_memcpy_xxx,
and are now used through a memcpy_dma_ops.
Tested-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Those structs are used only at bdisp-hw, so they shouldn't be
there in a header file that it is used elsewhere.
This fixes the following Gcc 6.1 warnings:
In file included from drivers/media/platform/sti/bdisp/bdisp-debug.c:11:0:
drivers/media/platform/sti/bdisp/bdisp-filter.h:207:65: warning: ‘bdisp_v_spec’ defined but not used [-Wunused-const-variable=]
static const struct __maybe_unused bdisp_filter_v_spec bdisp_v_spec[] = {
^~~~~~~~~
In file included from drivers/media/platform/sti/bdisp/bdisp-debug.c:11:0:
drivers/media/platform/sti/bdisp/bdisp-filter.h:23:65: warning: ‘bdisp_h_spec’ defined but not used [-Wunused-const-variable=]
static const struct __maybe_unused bdisp_filter_h_spec bdisp_h_spec[] = {
^~~~~~~~~
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Gcc 6.1 warns about an unused table:
drivers/media/i2c/adv7842.c:2400:27: warning: 'prim_mode_txt' defined but not used [-Wunused-const-variable=]
static const char * const prim_mode_txt[] = {
^~~~~~~~~~~~~
That seems to be useful for debug, and likely were used before.
While we could simply remove, let's comment it out, for now.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Gcc 6.1 warns about an unused table:
drivers/media/usb/em28xx/em28xx-dvb.c:907:38: warning: 'pctv_461e_m88ds3103_config' defined but not used [-Wunused-const-variable=]
static const struct m88ds3103_config pctv_461e_m88ds3103_config = {
^~~~~~~~~~~~~~~~~~~~~~~~~~
That's a left over of patch 76b91be3d3 ('em28xx: PCTV 461e use I2C
client for demod and SEC').
Remove the dead code.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Gcc 6.1 warns about some unused vars. Remove them:
drivers/media/platform/vivid/vivid-vid-cap.c:40:2: warning: 'tpf_default' defined but not used [-Wunused-const-variable=]
tpf_default = {.numerator = 1, .denominator = 30};
^~~~~~~~~~~
drivers/media/platform/vivid/vivid-sdr-cap.c:54:27: warning: 'NUM_FORMATS' defined but not used [-Wunused-const-variable=]
static const unsigned int NUM_FORMATS = ARRAY_SIZE(formats);
^~~~~~~~~~~
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Gcc 6.1 warns about some unused tables:
drivers/media/pci/zoran/zr36016.c:251:18: warning: 'zr016_yoff' defined but not used [-Wunused-const-variable=]
static const int zr016_yoff[] = { 8, 9, 7 };
^~~~~~~~~~
drivers/media/pci/zoran/zr36016.c:250:18: warning: 'zr016_xoff' defined but not used [-Wunused-const-variable=]
static const int zr016_xoff[] = { 20, 20, 20 };
^~~~~~~~~~
Those tables aren't used anywere. So, remove them.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As Gcc6.1 warned, those tables are currently unused:
drivers/media/tuners/r820t.c:349:18: warning: 'r820t_mixer_gain_steps' defined but not used [-Wunused-const-variable=]
static const int r820t_mixer_gain_steps[] = {
^~~~~~~~~~~~~~~~~~~~~~
drivers/media/tuners/r820t.c:345:18: warning: 'r820t_lna_gain_steps' defined but not used [-Wunused-const-variable=]
static const int r820t_lna_gain_steps[] = {
^~~~~~~~~~~~~~~~~~~~
They're actually used only by a routine that it is currently
commented out. So, move those tables to be together with such
code and comment them out.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Those tables are currently unused, so comment them out:
drivers/media/dvb-frontends/dib0090.c:852:18: warning: 'rf_ramp_pwm_sband' defined but not used [-Wunused-const-variable=]
static const u16 rf_ramp_pwm_sband[] = {
^~~~~~~~~~~~~~~~~
drivers/media/dvb-frontends/dib0090.c:800:18: warning: 'bb_ramp_pwm_boost' defined but not used [-Wunused-const-variable=]
static const u16 bb_ramp_pwm_boost[] = {
^~~~~~~~~~~~~~~~~
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Avoid this warning:
drivers/media/dvb-frontends/drx39xyj/drxj.c:1243:18: warning: 'nicam_presc_table_val' defined but not used [-Wunused-const-variable=]
static const u16 nicam_presc_table_val[43] = {
^~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The PCI device ID table is only used if compiled with modules
support. When compiled with modules disabled, this is now
producing this bogus warning:
drivers/media/pci/cx25821/cx25821-alsa.c:696:35: warning: 'cx25821_audio_pci_tbl' defined but not used [-Wunused-const-variable=]
static const struct pci_device_id cx25821_audio_pci_tbl[] = {
^~~~~~~~~~~~~~~~~~~~~
Fix it by annotating that the function may not be used.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
