[why]
there are some scaling capabilities such as fp16 which are known to be unsupported
on a given ASIC. exposing these static capabilities allows much simpler implementation
for OS interfaces which require to report such static capabilities to reduce the
number of dynamic validation calls
[how]
refactor the existing plane caps to be more extensible, and add fp16 and scaling
capabilities
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet Lakha@amd.com>
Acked-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The current dc_caps doesn't provide the information needed to
determine the count and type of each plane to be exposed to userspace.
There are three types of DRM planes that are exposed to userspace:
1. Primary planes (can be used for modesetting)
2. Overlay planes (can be blended below or above a primary plane)
3. Cursor planes (blended topmost)
We need to know the number and type of each in amdgpu_dm to expose
to userspace.
Hardware supports blending planes below, above or both ways depending
on the ASIC. Alpha support is also ASIC dependent. Some hardware has
dedicated pipes for overlays and other hardware combines the pipes.
All of this should be exposed in a way that DM can query and use.
[How]
Introduce the dc_plane_cap structure that describes the capabilities
for the hw planes.
It describes:
- the type of the plane
- whether the plane can blend with planes below it
- whether the plane can blend with planes above it
- whether the plane supports per pixel alpha blending
- supported formats on the plane (partial list for now)
Pre DCN ASICs don't have their full capabilities described for now.
They can be updated as needed in the future.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For fastboot, Bios will light up eDP before SW driver is loaded. SW
driver will check if eDP is lit by bios through reading the
BIOS_SCRATCH_3 register. If lit, SW driver will not power down eDP
power and phy to save time.
Definition of BIOS_SCRATCH_3 are missing for pre-raven asic. This
causes eDP fast boot to not work property. For some eDP panels, even
if dp tx sends NoVideoStream_flag =1 and dpcd 0x600=2, eDP rx may not
handle properly. This may cause a short flash on screen.
[How] Add definition of BIOS_SCRATCH_3 for all asic
Signed-off-by: hersen wu <hersenxs.wu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Yongqiang Sun <yongqiang.sun@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The aux_engine struct is needlessly complex and
is defined multiple times. It contains function pointers
that each have only one version and are called only from
inside dce_aux.
[How]
Replace aux_engine with a new struct called dce_aux.
Remove all function pointers and call functions directly.
Remove unused functions
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When XGMI is enabled, we need to adjust the dprefclk according to the
WAFL link's spread spectrum info. This is for VG20 (DCE121) only.
[How]
dce_clk_mgr already stores SS info, currently being used by audio clock.
Therefore, patch the clk_mgr's SS info with the xGMI SS info, if xGMI
is enabled. For display clock, adjust it during dce12_update_clocks()
before calling set_clock().
Since we rely on a mmhub register to reliably determine if xGMI is
enabled, the patching step needs to happen after resource_construct()
has initialized the hardware sequencer.
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In preparation for adding the actual dccg block since the
current implementation of dccg is mor eof a clock manager
than a hw block
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Need separate feature flag for DP 4:2:0 support, since existing
flag is used for HDMI
[How]
Added dp_ycbcr420_supported to struct encoder_feature_support
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently dccg contains code related to every dcn revision in
a single file.
This change splits out the dcn parts of code into correct folders
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This is done to clear up the clock programming sequence
since the only time we need to notify pplib is after
clock update.
This also renames the clk block to dccg, at the moment
this block contains both clock management and dccg
functionality.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
ddc engines were recently changed to be independently tracked
from pipe count. the change was reflected in resource constructor
but not in destructor. this manifests as a memory leak when
pipe harvesting is enabled, since not all constructed ddc engines
are freed
[how]
make destructor symmetric with constructor for all dcX_resource
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
All ASICS we support has YCbCr support, so
the check is unnecessary, the currently logic
in validate output also returns true all
the time, so the unneccessary logic is removed
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
-----BEGIN PGP SIGNATURE-----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=dMl4
-----END PGP SIGNATURE-----
BackMerge v4.19-rc6 into drm-next
I have some pulls based on rc6, and I prefer to have an explicit backmerge.
Signed-off-by: Dave Airlie <airlied@redhat.com>
[Why]
There have been a few reports of Vega10 display remaining blank
after S3 resume. The regression is caused by workaround for mode
change on Vega10 - skip set_bandwidth if stream count is 0.
As a result we skipped dispclk reset on suspend, thus on resume
we may skip the clock update assuming it hasn't been changed.
On some systems it causes display blank or 'out of range'.
[How]
Revert "drm/amd/display: Fix Vega10 black screen after mode change"
Verified that it hadn't cause mode change regression.
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Clock sources currently have support for asic specific
function pointers. But actual separation into functions
was never performed, leaving us with giant functions that
rely on switch.
This change creates separate functions, removing switch use.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
AMD Stoney reference board, there are only 2 pipes (not include
underlay), and 3 connectors. resource creation, only
2 I2C/AUX engines are created. Within dc_link_aux_transfer, when
pin_data_en =2, refer to enengines[ddc_pin->pin_data->en] = NULL.
NULL point is referred later causing system crash.
[how]
each asic design has fixed number of ddc engines at hw side.
for each ddc engine, create its i2x/aux engine at sw side.
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
I2C code did not match dc resource model and was generally
unpleasant
[How]
Move code into new svelte dce_i2c files, replacing various i2c
objects with two structs: dce_i2c_sw and dce_i2c_hw. Fully split
sw and hw code paths. Remove all redundant declarations. Use
address lists to distinguish between versions. Change dce80 code
to newer register access macros.
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DOUBLE_BUFFER_EN bit is getting cleared before enable blanking.
That leads to CRTC_BLANK_DATA_EN is getting updated immediately.
[How]
Get DOUBLE_BUFFER_EN bit set, the same as DCE110.
Signed-off-by: Jerry (Fangzhi) Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
for vega, dp set_panel_mode is
handled by psp firmware. dal should not program the
register again.
[how]
dal does not program panel mode.
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The sequence is slightly changed when bring .set_bandwidth out
from the end of programming backend to the end of programming
surface. Vega10 doesn't like to get clocks updated if
stream_count is zero in the current context (Atomic Reset).
[How]
Do not update clocks if no stream is showing up in the context.
Fixes 1b2b130192 "dc: Remove 300Mhz minimum disp clk limit."
Signed-off-by: Jerry (Fangzhi) Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
engine and aux_engine are unnecessary layers we want to remove this
layer.
[How]
flatten engine and aux engine structs into one struct called
aux_engine and remove all references to the engine struct.
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
confusing as to which part of debug is informational, and which part causes behavioral change
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Aux engine is created from i2caux layer. We want to remove this layer
and use the engine directly.
[How]
Decouple aux engine from i2caux. Move aux engine related code to dce folder and use
dc resource pool to manage the engine. And use the engine functions directly
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Leftover from bringup. No need to keep it around for
upstream.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Retrieve fuses to determine the availability of pipes, and
eliminate pipes that cannot be used.
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Jerry (Fangzhi) Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Override the memory input functions for dce120 not to program
new registers on dce112.
This will fix warnings thrown on Polaris asics.
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use tg count in resource pool for further reference.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Our APUs (Carrizo, Stoney, Raven) don't support it.
v2: Don't use is_apu as other ASICs might also not support it
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJaNy81AAoJEHm+PkMAQRiGq2YH/1C1so18qErhPosdfeLIXLbA
iC9XcIvkPuMfjDw4EfSWOzhKnzgqGuc8q/Vzz0ulDreNVUb52nBeRy69QgNoZBTB
NkLdrUKBnlArvRhBXToQGW/s1eI/gobuHBJb7/fbpvsUtPYcDE2nUXAEsMlagn5L
BMHNzE3TByaWj0SqJtZAZvaQN2MdWV8ArHBPaC+MtR2C1VJIyl0mT9CdCu2NpTES
+FncKJ6/qplSBNSUJSfYmFLfEKVcQxvHMi1kp9jOGlVjPM3cOPKRpv8x69x/IPoB
3l82AikL+Ju0738oJ0Fp/IhfGUqpXz+FwUz1JmCdrcOby75RHomJuJCUBTtjXA4=
=lYkx
-----END PGP SIGNATURE-----
BackMerge tag 'v4.15-rc4' into drm-next
Linux 4.15-rc4
Daniel requested it to fix some messy conflicts.
Remove asic_reg/vega10 folder.
Signed-off-by: Feifei Xu <Feifei.Xu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cleanup asic_reg/vega10/NBIO folder.
Signed-off-by: Feifei Xu <Feifei.Xu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Was missing license text.
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Felix Kuehling <Felix.Kuehling@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This fixes all the current smatch:
warn: inconsistent indenting
Reviewed-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Now that the registers exist, assign them to the resource_straps struct.
v2: Fix indentation
v3: Fix trailing whitespace and checkpatch warnings.
bug: https://bugs.freedesktop.org/show_bug.cgi?id=103404
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Leo (Sunpeng) Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This isn't used or required.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This removes any remaining pointless return codepaths from the
DCE code.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This never returns anything but true.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This doesn't return anything except true.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This only ever returned true.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The checks weren't useful here really.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Until now new context would start as empty, then populated
with exsisting pipes + new. Now we start with duplication
of existing context and then add/delete from the context
pipes as needed.
This allows to do a per stream resource
population, start discarding dc_validation_set
and by this brings DC closer to to DRM.
v2: Add some fixes and rebase.
Signed-off-by: Andrey Grodzovsky <Andrey.Grodzovsky@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
-Flattening core_dc to dc
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
