This patch adds a PHY reset function ixgbe_reset_phy_t_X550em. Which
allows devices that have LASI support in enable their interrupt.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds x550 external PHY interrupt and forced 1G/10G support.
This included enabling and handling LSC and thermal sensor interrupt.
ixgbe_handle_lasi() has been added for handling the interrupts received
over SDP0 from the external 10baseT PHY. ixgbe_enable_lasi_ext_t_x550em
and ixgbe_get_lasi_ext_t_x550em have been added to X550em to enable
mask and check interrupt flags for the external PHY.
Forced 1G/10G link speed is handled via ixgbe_mac_link_t_X550em.
ixgbe_seupt_mac_link_t_X550em sets up the internal PHY and external PHY
to either iXFI (10G) or KX (1G) based on the user selected auto
advertised link speed setting. Then sets up the external PHY auto
advertised link speed.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The I2C mux control relies on the SDP setting in the ESDP register
so it is necessary to restore the value after a MAC reset. Combine
all this functionality in to a support function.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This new method will control the PHY power state. You pass in the
state you wish to change to (ether on or off). For cases where this
method is not used the current PHY power state behavior is maintained.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a define for the new PHY identification as well as it's mapping
to the correct PHY type. Also allow ethtool to identify this type
as well.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
These Device ID could support both WoL and autoneg flow control. In
the case of WoL this is indicated by the eeprom. This patch enables
these devices this support.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Some of the register addresses and format where unfortunately changed
between MAC types. To get around this we add a const u32 *mvals pointer
to the ixgbe_hw struct to point to an array of mac-type-dependent
values. These can include register offsets, masks, whatever can be in
a u32. When the ixgbe_hw struct is initialized, a pointer to the
appropriate array must be set.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix the device tree entries to modify the '_' to '-'.
Also changes the names of the internal delay properties
from -int- to -internal- as the -int- appeared as a keyword.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the AFE_TX_CONFIG value to solve marginal rise/fall issues
observed when the link is operating in 100BaseT. This workaround applies
to GPHY revisions D0, E0 and newer.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RGMII block is currently only powered on when using RGMII or
RGMII_NO_ID, which is not correct when using the GENET interface in MII
or Reverse MII modes. We always need to power on the RGMII interface for
this block to properly work, regardless of the MII mode in which we
operate.
Fixes: aa09677cba ("net: bcmgenet: add MDIO routines")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Link failures have been observed when using the KSZ9031 with HP 1810-8G
and HP 1910-8G network switches. Center the FLP timing at 16ms to help
avoid intermittent link failures.
>From the KSZ9031RNX and KSZ9031MNX data sheets revision 2.2, section
"Auto-Negotiation Timing":
The KSZ9031[RNX or MNX] Fast Link Pulse (FLP) burst-to-burst
transmit timing for Auto-Negotiation defaults to 8ms. IEEE 802.3
Standard specifies this timing to be 16ms +/-8ms. Some PHY link
partners need to receive the FLP with 16ms centered timing;
otherwise, there can be intermittent link failures and long
link-up times.
The PHY data sheet recommends configuring the FLP burst registers after
power-up/reset and immediately thereafter restarting auto-negotiation, so
we center the FLP timing at 16ms and then restart auto-negotiation in the
config_init for KSZ9031.
Signed-off-by: Jaeden Amero <jaeden.amero@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some defines for a few pad skew related extended registers.
Specify for which MMD Address (dev_addr) they are for.
Signed-off-by: Jaeden Amero <jaeden.amero@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a few places in this driver, we weren't using const where we could
have. Use const more.
In addition, change the arrays of strings in ksz9031_config_init() to be
not only const, but also static.
Signed-off-by: Jaeden Amero <jaeden.amero@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
API compliance scanning with coccinelle flagged:
./drivers/net/wan/dscc4.c:1036:1-33:
WARNING: timeout (10) seems HZ dependent
./drivers/net/wan/dscc4.c:554:2-34:
WARNING: timeout (10) seems HZ dependent
./drivers/net/wan/dscc4.c:599:2-34:
WARNING: timeout (10) seems HZ dependent
Numeric constants passed to schedule_timeout_*() make the effective
timeout HZ dependent which does not seem to be the intent here.
Fixed up by converting the constant to jiffies with msecs_to_jiffies(),
passing 100ms (assuming HZ==100 in the original code).
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
API compliance scanning with coccinelle flagged:
./drivers/net/wan/cosa.c:520:2-18: WARNING:
timeout (30) seems HZ dependent
Numeric constants passed to schedule_timeout() make the effective
timeout HZ dependent which makes little sense in a device probe.
Fixed up by converting the constant to jiffies with msecs_to_jiffies()
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix static checker warnings in the flow of system guid query.
Fixes: 707c4602cd ('net/mlx5_core: Add new query HCA vport commands')
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the driver gets unregistered a call to netif_napi_del() was
missing, this all was also missing in the error paths of
b44_init_one().
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
use time_is_before_eq_jiffies macro for time comparison
Signed-off-by: Antonio Murdaca <antonio.murdaca@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are several places in the driver (all in control paths) where
coherent dma memory is being allocated using either dma_alloc_coherent()
or the deprecated pci_alloc_consistent(). All these calls should be
changed to use dma_zalloc_coherent() to avoid uninitialized fields in
data structures backed by this memory.
Reported-by: Joerg Roedel <jroedel@suse.de>
Tested-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current driver adjust freq formula is:
fe * diff = ppb * pc
Note:
fe: ENET ref clock frequency in Hz
diff = inc_corr - inc: difference between default increment and correction increment
ppb: parts per billion adjustment from base
pc: correction period (in number of fe clock cycles)
The correction increment will be used after N cycles of regular increments,
not every N cycles (with N being the correction period). For example, set ENET_ATCOR=4,
INC=8, INC_CORR=9, there will be 4 increments of 8 (ENET_ATINC[INC]) , followed by 1
increment of 9 (ENET_ATINC[INC_CORR]).
So, the correct formula is:
fe * diff = ppb * (pc + 1)
For ENET_ATCOR, a value 0 disables the correction counter and no corrections occur.
So base on the origin formula, set pc = pc > 1 ? pc - 1 : pc.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove sparse warnings:
drivers/net/ethernet/xilinx/ll_temac_main.c:65:16: warning: cast removes
address space of expression
drivers/net/ethernet/xilinx/ll_temac_main.c:70:9: warning: cast removes
address space of expression
drivers/net/ethernet/xilinx/ll_temac_main.c:127:16: warning: cast
removes address space of expression
drivers/net/ethernet/xilinx/ll_temac_main.c:137:9: warning: cast removes
address space of expression
drivers/net/ethernet/xilinx/ll_temac_main.c:409:3: warning: symbol
'temac_options' was not declared. Should it be static?
drivers/net/ethernet/xilinx/ll_temac_main.c:590:6: warning: symbol
'temac_adjust_link' was not declared. Should it be static?
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dump useful ring statistics along with interrupt status, software
maintained pointers and hardware registers to help troubleshoot TX queue
stalls.
When a timeout occurs, disable TX NAPI for the rings, dump their states
while interrupts are disabled, re-enable interrupts, NAPI and queue flow
control to help with the recovery.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ethtool -S on a DSA interface can deadlock for some switches because
the same lock is taken twice. Use the register read function which
expects the lock to be already held.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Fixes: 31888234b7 ("net: dsa: mv88e6xxx: Replace stats mutex with SMI mutex")
Signed-off-by: David S. Miller <davem@davemloft.net>
The debug is printing the struct smt_header * address using
the %x format specifier. Fix it to use %p instead.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the Tx timer function runs in softirq context the driver needs
to call disable_irq_nosync instead of a disable_irq.
Reported-by: Josh Stone <jistone@redhat.com>
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix:
drivers/net/wan/dscc4.c: In function 'dscc4_open':
drivers/net/wan/dscc4.c:1049:25: warning: variable 'ppriv' set but not used
[-Wunused-but-set-variable]
This has been in there unused since 1da177e4c3 (Linux-2.6.12-rc2) simply
remove it.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch e85c9a7abf: ("cxgb4/cxgb4vf: Add code to calculate T5 BAR2
Offsets for SGE Queue Registers") from Dec 3, 2014, leads to the
following static checker warning:
drivers/net/ethernet/chelsio/cxgb4/t4_hw.c:5358
t4_bar2_sge_qregs()
warn: should '(qid >> qpp_shift) << page_shift' be a 64 bit type?
This patch fixes it
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TP_PIO_{ADDR,DATA} registers are are in conflict with the firmware's
use of these registers. Added a routine to access it through FW LDST
cmd.
Access all TP_PIO_{ADDR,DATA} register access through new routine if FW
is alive. If firmware is dead, than fall back to indirect access.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Grab the Adapter MAC Address out of the VPD and use it for the "debug"
network interface when either we can't contact the firmware
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
t4_link_start() was completely misnamed. It does _not_ start up the
link. It merely does the L1 Configuration for the link. The Link Up
process is started automatically by the firmware when the number of
enabled Virtual Interfaces on a port goes from 0 to 1. So renaming
this routine to t4_link_l1cfg() for better documentation.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add function to flush the sge ec context cache, and utilize
this new function in the driver
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Free VI interfaces in remove routine. If we don't do this then the
firmware will never drop the physical link to the peer.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If SRIOV is enabled we need to be in VEB mode not VEPA mode at probe.
This fixes an NPAR bug when SRIOV is enabled in the BIOS.
Change-ID: Ibf006abafd9a0ca3698ec24848cd771cf345cbbc
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The patch fixes a bug in the default configuration which
prevented a software bridge loaded on the PF interface from
working correctly because broadcast packets are incorrectly
looped back.
Fix the general case, by loading the driver in VEPA mode Until a
VF or VMDq VSI is added. This way loopback on the Main VSI is
turned off until needed and can resolve the issue of unnecessary
reflection for users that do not have VF or VMDq VSIs setup.
The driver must now coordinate the loopback setting for the Flow
Director (FDIR) VSI to make sure it is in sync with the current
VEB or VEPA mode setting.
The user can still switch bridge modes from the bridge commands and
choose to be in VEPA mode with VF VSIs. Because of hardware
requirements, the call to switch to VEB mode when no VF/VMDqs are
present will be rejected.
NOTE: This patch uses BIT_ULL as that is preferred going forward,
a followup patch in the lower priority queue to net-next will fix
up the remaining 1 << usages.
Change-ID: Ib121ddb18fe4b3c4f52e9deda6fcbeb9105683d1
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Ethernet functionality is only available when working in ISSI > 0 mode.
Previously, the IB driver wasn't ready to work on that mode, and hence
building both the IB driver and the Ethernet functionality in the core
driver were disallowed by Kconfigs.
Now, once we have all the pre-steps in place, we can remove this limitation.
The last steps in the IB driver for getting that setup to work are:
create dummy SRQ for the driver's use (until now we could use XRC_SRQ
as SRQ and XRC_SRQ, after moving to ISSI > 0, we separate XRC SRQs from
basic SRQs) and adapt the create QP function to be compatible with ISSI > 0.
Signed-off-by: Haggai Abramovsky <hagaya@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the following helpers:
1. mlx5_query_port_proto_oper -- queries the port speed port mask
2. mlx5_query_port_link_width_oper - queries the port link with bitmask
3. mlx5_query_port_vl_hw_cap - queries the Virtual Lanes supported on this port
These helpers will be used from the IB driver when working in ISSI > 0 mode.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now, mlx5_query_port_ptys always queried port number one.
Added new argument in the function's prototype so we can also query
the second port. This will be needed when thr helper will be invoked
from the IB driver on non FPP (Function-Per-Port) devices.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the function prototypes for max and operational mtu to take the
local port number. In the Ethernet driver is this hard coded to one,
since ConnectX4 Ethernet devices are always function-per-port.
The IB driver also serves older devices (ConnectIB) which isn't such,
and hence the part can vary.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add two wrapper functions to the query adapter command:
1. mlx5_query_board_id -- replaces the old mlx5_cmd_query_adapter.
2. mlx5_core_query_vendor_id -- retrieves the vendor_id from the
query_adapter command.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added the implementation for the following commands:
1. QUERY_HCA_VPORT_GID
2. QUERY_HCA_VPORT_PKEY
3. QUERY_HCA_VPORT_CONTEXT
They will be needed when we move to work with ISSI > 0 in the IB driver too.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the vport header file to be under include/linux/mlx5, such that
the mlx5 IB can use it as well.
Also add nic_ prefix to the vport NIC commands to differeniate between
HCA vport commands and NIC vport commands.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The determination of the supported ISSI versions should be conditioned
on the returned mask, and not only on the return status of the query
ISSI command, fix that.
Signed-off-by: Haggai Abramovsky <hagaya@mellanox.com>
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When working in ISSI > 0 mode, the model exposed by the device for
XRCs and SRQs is different. XRCs use XRC SRQs and plain SRQs are based
on RPM (Receive Memory Pool).
Add helper functions to create, modify, query, and arm XRC SRQs and RMPs.
Signed-off-by: Haggai Abramovsky <hagaya@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some core helper functions were named with mlx5_ only prefix, fix that to
mlx5_core_ so we're aligned with the overall scheme used for core services.
Signed-off-by: Haggai Abramovsky <hagaya@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch afb736e933: "net/mlx5: Ethernet resource handling files"
from May 28, 2015, leads to the following static checker warning:
drivers/net/ethernet/mellanox/mlx5/core/en_flow_table.c:726 mlx5e_create_main_flow_table()
error: potential null dereference 'g'. (kcalloc returns null)
Fixes: afb736e933 ("net/mlx5: Ethernet resource handling files")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds full IPv6 addresses into flow_keys and uses them as
input to the flow hash function. The implementation supports either
IPv4 or IPv6 addresses in a union, and selector is used to determine
how may words to input to jhash2.
We also add flow_get_u32_dst and flow_get_u32_src functions which are
used to get a u32 representation of the source and destination
addresses. For IPv6, ipv6_addr_hash is called. These functions retain
getting the legacy values of src and dst in flow_keys.
With this patch, Ethertype and IP protocol are now included in the
flow hash input.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ath10k:
* qca6174 power consumption improvements, enable ASPM etc (Michal)
wil6210:
* support Wi-Fi Simple Configuration in STA mode
iwlwifi:
* a few fixes (re-enablement of interrupts for certain new
platforms that have special power states)
* Rework completely the RBD allocation model towards new
multi RX hardware.
* cleanups
* scan reworks continuation (Luca)
mwifiex:
* improve firmware debug functionality
rtlwifi:
* update regulatory database
brcmfmac:
* cleanup and new feature support in PCIe code
* alternative nvram loading for router support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJVb1cPAAoJEG4XJFUm622bP0oIAKhUBlC3rtrOJd+9kREAGUJQ
Dk2xZr/p6hdb4dSHHKKroBr5mfryHknSs+AI5akJMph36DoBMD+Mwb4HlcL9cI5J
RXIjIvQEADsK+6ME7cqnw2htWlYsX8aJI96/2Eusveo/zHyAG3+eBC3wkyqWBlBK
EGV5ziClSe5pE5yGWj5tyr9me+qRQiO+dFJK1AoRE3Zq4pjj+5VDZoVQN0GNZGP7
lgeNOzvPxWt+ZseslP8IeCedN5c+NpacD889NnQJyMXaouSp7LmMod000bjnKK8o
9sRHsKxI5qHgC4mUa3Tk3cEnFqVYAo8KKOVaBVtKsMc4XoO/Qov6Z0AtXig5Xnk=
=CM/T
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2015-06-03' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
new driver mt7601u for MediaTek Wi-Fi devices MT7601U
ath10k:
* qca6174 power consumption improvements, enable ASPM etc (Michal)
wil6210:
* support Wi-Fi Simple Configuration in STA mode
iwlwifi:
* a few fixes (re-enablement of interrupts for certain new
platforms that have special power states)
* Rework completely the RBD allocation model towards new
multi RX hardware.
* cleanups
* scan reworks continuation (Luca)
mwifiex:
* improve firmware debug functionality
rtlwifi:
* update regulatory database
brcmfmac:
* cleanup and new feature support in PCIe code
* alternative nvram loading for router support
====================
Conflicts:
drivers/net/wireless/iwlwifi/Kconfig
Trivial conflict in iwlwifi Kconfig, two commits adding
the same two chip numbers to the help text, but order
transposed.
Signed-off-by: David S. Miller <davem@davemloft.net>
