The few callers can just use dma_set_max_seg_size ()directly.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
After bfcb79fca1 ("PCI/ERR: Run error recovery callbacks for all affected
devices"), AER errors are always cleared by the PCI core and drivers don't
need to do it themselves.
Remove calls to pci_cleanup_aer_uncorrect_error_status() from device
driver error recovery functions.
Signed-off-by: Oza Pawandeep <poza@codeaurora.org>
[bhelgaas: changelog, remove PCI core changes, remove unused variables]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
*) Add new PHY driver for Socionext PCIe, USB2 and USB3 PHY
*) Add new PHY driver for Rockchip HDMI PHY
*) Add new PHY driver for Cadence display port PHY
*) Add support for UFS PHY in Qualcomm's SDM845 SoC
*) Add correct PHY init sequence for BCM63138 SATA PHY
*) Add support for bringing the uart2 out through the usb dm+dp pin in
Rockchips's rk3188
*) Re-design R-Car Gen3 USB PHY w.r.t support for OTG
*) Cleanup Qualcomm's UFS PHY, QMP PHY (for PCIe and USB3) and QUSB2 PHY
*) A preparation patch to remove the node name pointer from struct device_node
*) Minor cleanups in some of the other PHY drivers.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
-----BEGIN PGP SIGNATURE-----
iQJCBAABCgAsFiEEUXMr/TfP2p4suIY5Dlx4XIBNgtkFAlux7wkOHGtpc2hvbkB0
aS5jb20ACgkQDlx4XIBNgtmNQw/7B1sWFyT8yhD8yTXVpV+3N7ziy2T25ABLaFsV
mmXafs3x8UMVC2I4NLbF5KZ3ysmfJI6J/jP0I1PSWfviZJzcmYxN99uFG3Rsnw3N
UVc9BlkDtOG0PLjULEiVLJdTi220zr6Jg8ZvZZCRM1rWTUugtgeX4Nnom6h58sxW
NFZxaR60V4NPvwBgXuqibbZqWvDVWSdz2OMhTNZiDQSauQU5U4P5qq0Fsz+/x5Uu
xoIT5EJ04kAtLGj1eCsgTRaY4Fpwmn2Skk+TSZt182pshKi/WaD//rE3Rxttrk6P
B4DdZ6UJRfO6+qFExVUrOm8tpnC8D7L1ZQPZ+smk1apNvwFkUAwkLPZ8YBPfMAK/
Qi08XQZtIv7yFW6BWZoWFGGihxR+7OrKUzDHw/64R863xvobSyvDUJ8+6cmnryec
zIm10q3H6aSC/1pDEGYR7EvKFG44qqIWkkR/2Ki9qI2F5kW3ZjJESIPrvu4MYalq
pSFb8YpwGPki57H6YrKLlvHFUVHiaza2C6KUHpmtbhb2+xS3ULmbEi3yCIzt99RZ
8u8/bOcA7qU+K21YUQOVG+vElBBtgBcqvydc91HdNWZQYlbuqH5DErrstD52Tn0L
bmRa1H1A2l9l3vT4ioYmd2kEp/F88wK+Qyx7XVIN/qMGp6KYLqmMKuY2CkWgGyqV
aukQ3TA=
=A4II
-----END PGP SIGNATURE-----
Merge tag 'phy-for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next
Kishon writes:
phy: for 4.20
*) Add new PHY driver for Socionext PCIe, USB2 and USB3 PHY
*) Add new PHY driver for Rockchip HDMI PHY
*) Add new PHY driver for Cadence display port PHY
*) Add support for UFS PHY in Qualcomm's SDM845 SoC
*) Add correct PHY init sequence for BCM63138 SATA PHY
*) Add support for bringing the uart2 out through the usb dm+dp pin in
Rockchips's rk3188
*) Re-design R-Car Gen3 USB PHY w.r.t support for OTG
*) Cleanup Qualcomm's UFS PHY, QMP PHY (for PCIe and USB3) and QUSB2 PHY
*) A preparation patch to remove the node name pointer from struct device_node
*) Minor cleanups in some of the other PHY drivers.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
* tag 'phy-for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy: (41 commits)
phy: renesas: convert to SPDX identifiers
phy: lantiq: Fix compile warning
phy: qcom-ufs: Declare 20nm qcom ufs qmp phy as Broken
scsi/ufs: qcom: Remove ufs_qcom_phy_*() calls from host
phy: qcom-ufs: Remove stale methods that handle ref clk
dt-bindings: phy-qcom-qmp: Add UFS phy compatible string for sdm845
phy: Add QMP phy based UFS phy support for sdm845
phy: General struct and field cleanup
phy: Update PHY power control sequence
phy: rockchip-usb: add usb-uart setup for rk3188
phy: phy-twl4030-usb: fix denied runtime access
phy: renesas: rcar-gen3-usb2: add is_otg_channel to use "role" sysfs
phy: renesas: rcar-gen3-usb2: add conditions for uses_otg_pins == false
phy: renesas: rcar-gen3-usb2: change a condition "dr_mode"
phy: renesas: rcar-gen3-usb2: unify OBINTEN handling
phy: renesas: rcar-gen3-usb2: Check a property to use otg pins
phy: renesas: rcar-gen3-usb2: Rename has_otg_pins to uses_otg_pins
phy: renesas: rcar-gen3-usb2: fix vbus_ctrl for role sysfs
dt-bindings: rcar-gen3-phy-usb2: add no-otg-pins property
phy: brcm-sata: Add BCM63138 (DSL) PHY init sequence
...
-----BEGIN PGP SIGNATURE-----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=dMl4
-----END PGP SIGNATURE-----
Merge tag 'v4.19-rc6' into for-4.20/block
Merge -rc6 in, for two reasons:
1) Resolve a trivial conflict in the blk-mq-tag.c documentation
2) A few important regression fixes went into upstream directly, so
they aren't in the 4.20 branch.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
* tag 'v4.19-rc6': (780 commits)
Linux 4.19-rc6
MAINTAINERS: fix reference to moved drivers/{misc => auxdisplay}/panel.c
cpufreq: qcom-kryo: Fix section annotations
perf/core: Add sanity check to deal with pinned event failure
xen/blkfront: correct purging of persistent grants
Revert "xen/blkfront: When purging persistent grants, keep them in the buffer"
selftests/powerpc: Fix Makefiles for headers_install change
blk-mq: I/O and timer unplugs are inverted in blktrace
dax: Fix deadlock in dax_lock_mapping_entry()
x86/boot: Fix kexec booting failure in the SEV bit detection code
bcache: add separate workqueue for journal_write to avoid deadlock
drm/amd/display: Fix Edid emulation for linux
drm/amd/display: Fix Vega10 lightup on S3 resume
drm/amdgpu: Fix vce work queue was not cancelled when suspend
Revert "drm/panel: Add device_link from panel device to DRM device"
xen/blkfront: When purging persistent grants, keep them in the buffer
clocksource/drivers/timer-atmel-pit: Properly handle error cases
block: fix deadline elevator drain for zoned block devices
ACPI / hotplug / PCI: Don't scan for non-hotplug bridges if slot is not bridge
drm/syncobj: Don't leak fences when WAIT_FOR_SUBMIT is set
...
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When pcmcia_enable_device fails, the lack of error-handling code may
cause unexpected results.
This patch adds error-handling code after calling pcmcia_enable_device
in the qlogic_stub scsi driver.
Signed-off-by: Zhouyang Jia <jiazhouyang09@gmail.com>
Cc: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: linux-scsi@vger.kernel.org
[linux@dominikbrodowski.net: update commit message]
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Use module_pcmcia_driver for drivers whose init and exit functions
only register and unregister, respectively.
A simplified version of the Coccinelle semantic patch that performs
this transformation is as follows:
@a@
identifier f, x;
@@
-static f(...) { return pcmcia_register_driver(&x); }
@b depends on a@
identifier e, a.x;
@@
-static e(...) { pcmcia_unregister_driver(&x); }
@c depends on a && b@
identifier a.f;
declarer name module_init;
@@
-module_init(f);
@d depends on a && b && c@
identifier b.e, a.x;
declarer name module_exit;
declarer name module_pcmcia_driver;
@@
-module_exit(e);
+module_pcmcia_driver(x);
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Cc: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: linux-scsi@vger.kernel.org
[linux@dominikbrodowski.net:
- updated commit message
- drop change to fdomain which got removed in the meantime]
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
This patch fixes commit bcc71cc3cd ("scsi: qla2xxx: Fix for double
free of SRB structure") which placed code in wrong routines.
Also updated the use of WARN_ON() to WARN_ON_ONCE() to prevent
flooding log messages.
Fixes: bcc71cc3cd ("scsi: qla2xxx: Fix for double free of SRB structure")
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update device_add_disk() to take an 'groups' argument so that
individual drivers can register a device with additional sysfs
attributes.
This avoids race condition the driver would otherwise have if these
groups were to be created with sysfs_add_groups().
Signed-off-by: Martin Wilck <martin.wilck@suse.com>
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The SR_RST bit isn't latched. Hence, detecting a bus reset isn't reliable.
When it is detected, the right thing to do is to drop all connected and
disconnected commands. The code for that is already present so refactor it and
call it when SR_RST is set.
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The X3T9.2 specification (draft) says, under "6.1.4.2 RESELECTION time-out
procedure", that a target may assert RST or go to BUS FREE phase if the
initiator does not respond within 200 us. Something like this has been
observed with AztecMonster II target. When it happens, all we can do is wait
for the target to try again.
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The X3T9.2 specification (draft) says, under "6.1.4.1 RESELECTION",
... The reselected initiator shall then assert the BSY signal
within a selection abort time of its most recent detection of being
reselected; this is required for correct operation of the time-out
procedure.
The selection abort time is only 200 us which may be insufficient time for a
printk() call. Move the diagnostics to the error paths.
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When NCR5380_abort() returns FAILED, the driver forgets that the target is
still busy. Hence, further commands may be sent to the target, which may fail
during selection and produce the error message, "reselection after won
arbitration?". Prevent this by leaving the busy flag set when NCR5380_abort()
fails.
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The X3T9.2 specification (draft) says, under "6.1.4.1 RESELECTION", that "the
initiator shall not respond to a RESELECTION phase if other than two SCSI ID
bits are on the DATA BUS." This issue (too many bits set) has been observed in
the wild, so add a check.
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When sense data is valid, call set_driver_byte(cmd, DRIVER_SENSE). Otherwise
some callers of scsi_execute() will ignore sense data. Don't set DID_ERROR or
DID_RESET just because sense data is missing.
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is mostly needed because an AztecMonster II target has been observed
disconnecting REQUEST SENSE commands and then failing to reselect properly.
Suggested-by: Michael Schmitz <schmitzmic@gmail.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The return value is taken to mean "retry" or "don't retry". Change it to bool
to improve readability. Fix related comments. No functional change.
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Replace a 'goto' statement with a simple 'return' where possible. This
improves readability. No functional change.
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When doing a host reset we should be clearing all outstanding commands, not
just the command triggering the reset.
[mkp: adjusted Hannes' SoB address]
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Ondrey Zary <linux@rainbow-software.org>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The check for a non-zero drvr_wait is redundant as the same check is performed
earlier in the outer while loop, the inner check will always be true if we
reached this point inside the while loop. Remove the redundant if check.
Detected by cppcheck:
(warning) Identical inner 'if' condition is always true.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Manish Rangankar <Manish.Rangankar@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is a probability that the SRB structure might have been released by the
time the debug log message dereferences it. This patch moved the log messages
before the command is issued to the firmware to prevent unknown behavior and
kernel crash
Fixes: 726b854870 ("qla2xxx: Add framework for async fabric discovery")
Cc: <stable@vger.kernel.org>
Signed-off-by: Giridhar Malavali <giridhar.malavali@cavium.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch prevents user space mailbox request from doing chip reset if the
mailbox timed out. The chip reset is only reserved for the DPC thread to
ensure all mailbox requests are flushed properly. The DPC thread is
responsible for the flushing all MBs and chip reset.
Fixes: b2000805a9 ("scsi: qla2xxx: Flush mailbox commands on chip reset")
Cc: <stable@ger.kernel.org>
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch fixes multiple call for qla_nvme_unregister_remote_port() as part
of qlt_schedule_session_for_deletion(), Do not call it again during
qla_nvme_delete()
Fixes: e473b30741 ("scsi: qla2xxx: Add FC-NVMe abort processing")
Cc: <stable@vger.kernel.org>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch fixes issue where driver clears NPort ID map instead of marking
handle in use. Once driver clears NPort ID from the database, it can reuse
the same NPort ID resulting in a PLOGI failure.
[mkp: fixed Himanshu's SoB]
Fixes: a084fd68e1 ("scsi: qla2xxx: Fix re-login for Nport Handle in use")
Cc: <stable@vger.kernel.org>
Signed-of-by: Quinn Tran <quinn.tran@cavium.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Himanshu Madhani <hmadhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The response data buffer used in switch scan is reused 4 times. (For example,
for commands GPN_FT, GNN_FT for FCP and FC-NVME) Before driver reuses this
buffer, clear it to prevent duplicate entries in our database.
Fixes: a4239945b8 ("scsi: qla2xxx: Add switch command to simplify fabric discovery"
Cc: <stable@vger.kernel.org>
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch fixes issue when remoteport registers itself as both FCP and
FC-NVMe with the switch, driver will pick FC-NVMe personality as default when
scanning for targets.
Driver was using comaprative operator instead of bitwise operator to check for
fc4_type for both FCP and FC-NVME.
Fixes: 2b5b96473e ("scsi: qla2xxx: Fix FC-NVMe LUN discovery")
Cc: <stable@vger.kernel.org>
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We shouldn't allow negative thresholds. I don't know what it would do
but it can't be good.
Fixes: 8b4673ba3a ("scsi: qla2xxx: Add support for ZIO6 interrupt threshold")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Default value of ql2xasynctmfenable for qla2xxx driver was set to 1 in
commit 043dc1d7e8 ("scsi: qla2xxx: Enable Async TMF processing") but
comment in MODULE_PARAM_DESC was not modified.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The RQF_PREEMPT flag is used for three purposes:
- In the SCSI core, for making sure that power management requests
are executed even if a device is in the "quiesced" state.
- For domain validation by SCSI drivers that use the parallel port.
- In the IDE driver, for IDE preempt requests.
Rename "preempt-only" into "pm-only" because the primary purpose of
this mode is power management. Since the power management core may
but does not have to resume a runtime suspended device before
performing system-wide suspend and since a later patch will set
"pm-only" mode as long as a block device is runtime suspended, make
it possible to set "pm-only" mode from more than one context. Since
with this change scsi_device_quiesce() is no longer idempotent, make
that function return early if it is called for a quiesced queue.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Cc: Jianchao Wang <jianchao.w.wang@oracle.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Move the code for runtime power management from blk-core.c into the
new source file blk-pm.c. Move the corresponding declarations from
<linux/blkdev.h> into <linux/blk-pm.h>. For CONFIG_PM=n, leave out
the declarations of the functions that are not used in that mode.
This patch not only reduces the number of #ifdefs in the block layer
core code but also reduces the size of header file <linux/blkdev.h>
and hence should help to reduce the build time of the Linux kernel
if CONFIG_PM is not defined.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Jianchao Wang <jianchao.w.wang@oracle.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The host makes direct calls into phy using ufs_qcom_phy_*()
APIs. These APIs are only defined for 20nm qcom-ufs-qmp phy
which is not being used by any architecture as yet. Future
architectures too are not going to use 20nm ufs phy.
So remove these ufs_qcom_phy_*() calls from host to let further
change declare the 20nm phy as broken.
Also remove couple of stale enum defines for ufs phy.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
When the lldd is processing the complete sas task in interrupt and set the
task stat as SAS_TASK_STATE_DONE, the smp timeout timer is able to be
triggered at the same time. And smp_task_timedout() will complete the task
wheter the SAS_TASK_STATE_DONE is set or not. Then the sas task may freed
before lldd end the interrupt process. Thus a use-after-free will happen.
Fix this by calling the complete() only when SAS_TASK_STATE_DONE is not
set. And remove the check of the return value of the del_timer(). Once the
LLDD sets DONE, it must call task->done(), which will call
smp_task_done()->complete() and the task will be completed and freed
correctly.
Reported-by: chenxiang <chenxiang66@hisilicon.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
CC: John Garry <john.garry@huawei.com>
CC: Johannes Thumshirn <jthumshirn@suse.de>
CC: Ewan Milne <emilne@redhat.com>
CC: Christoph Hellwig <hch@lst.de>
CC: Tomas Henzl <thenzl@redhat.com>
CC: Dan Williams <dan.j.williams@intel.com>
CC: Hannes Reinecke <hare@suse.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: John Garry <john.garry@huawei.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When ata device IDENTIFY failed, the ata device status is ATA_DEV_UNKNOWN. The
libata reported like:
[113518.620433] ata5.00: qc timeout (cmd 0xec)
[113518.653646] ata5.00: failed to IDENTIFY (I/O error, err_mask=0x4)
But libsas verifies the device status by ata_dev_disabled(), which skipped
ATA_DEV_UNKNOWN. This will make libsas think the ata device probing succeed
the device cannot be actually brought up. And even the new bcast of this
device will be considered as flutter and will not probe this device again.
Change ata_dev_disabled() to !ata_dev_enabled() so that libsas can deal with
this if the ata device probe failed. New bcasts can let us try to probe the
device again and bring it up if it is fine to IDENTIFY.
Tested-by: Zhou Yupeng <zhouyupeng1@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
CC: John Garry <john.garry@huawei.com>
CC: Johannes Thumshirn <jthumshirn@suse.de>
CC: Ewan Milne <emilne@redhat.com>
CC: Christoph Hellwig <hch@lst.de>
CC: Tomas Henzl <thenzl@redhat.com>
CC: Dan Williams <dan.j.williams@intel.com>
CC: Hannes Reinecke <hare@suse.com>
Reviewed-by: John Garry <john.garry@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If we went into sas_rediscover_dev() the attached_sas_addr was already insured
not to be zero. So it's unnecessary to check if the attached_sas_addr is zero.
And although if the sas address is not changed, we always have to unregister
the old device when we are going to register a new one. We cannot just leave
the device there and bring up the new.
Signed-off-by: Jason Yan <yanaijie@huawei.com>
CC: chenxiang <chenxiang66@hisilicon.com>
CC: John Garry <john.garry@huawei.com>
CC: Johannes Thumshirn <jthumshirn@suse.de>
CC: Ewan Milne <emilne@redhat.com>
CC: Christoph Hellwig <hch@lst.de>
CC: Tomas Henzl <thenzl@redhat.com>
CC: Dan Williams <dan.j.williams@intel.com>
CC: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Now LLDDs have to implement lldd_port_deformed method otherwise NULL
dereference will happen. Make it optional and remove the dummy implementation
in hisi_sas.
Signed-off-by: Jason Yan <yanaijie@huawei.com>
CC: John Garry <john.garry@huawei.com>
CC: Johannes Thumshirn <jthumshirn@suse.de>
CC: Ewan Milne <emilne@redhat.com>
CC: Christoph Hellwig <hch@lst.de>
CC: Tomas Henzl <thenzl@redhat.com>
CC: Dan Williams <dan.j.williams@intel.com>
CC: Hannes Reinecke <hare@suse.com>
Acked-by: John Garry <john.garry@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This code is dead and no clue implies that it will be back again.
Signed-off-by: Jason Yan <yanaijie@huawei.com>
CC: John Garry <john.garry@huawei.com>
CC: Johannes Thumshirn <jthumshirn@suse.de>
CC: Ewan Milne <emilne@redhat.com>
CC: Christoph Hellwig <hch@lst.de>
CC: Tomas Henzl <thenzl@redhat.com>
CC: Dan Williams <dan.j.williams@intel.com>
CC: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: John Garry <john.garry@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Trivial fix to spelling mistake in warning message and comments
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Clang warns when multiple pairs of parentheses are used for a single
conditional statement.
In file included from drivers/scsi/BusLogic.c:57:
drivers/scsi/FlashPoint.c:2947:34: warning: equality comparison with extraneous parentheses [-Wparentheses-equality]
if ((currSCCB->Sccb_scsistat == SELECT_SN_ST)) {
~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~
drivers/scsi/FlashPoint.c:2947:34: note: remove extraneous parentheses around the comparison to silence this warning
if ((currSCCB->Sccb_scsistat == SELECT_SN_ST)) {
~ ^ ~
drivers/scsi/FlashPoint.c:2947:34: note: use '=' to turn this equality comparison into an assignment
if ((currSCCB->Sccb_scsistat == SELECT_SN_ST)) {
^~
=
drivers/scsi/FlashPoint.c:2956:39: warning: equality comparison with extraneous parentheses [-Wparentheses-equality]
else if ((currSCCB->Sccb_scsistat ==
~~~~~~~~~~~~~~~~~~~~~~~~^~
drivers/scsi/FlashPoint.c:2956:39: note: remove extraneous parentheses around the comparison to silence this warning
else if ((currSCCB->Sccb_scsistat ==
~ ^
drivers/scsi/FlashPoint.c:2956:39: note: use '=' to turn this equality comparison into an assignment
else if ((currSCCB->Sccb_scsistat ==
^~
=
2 warnings generated.
Link: https://github.com/ClangBuiltLinux/linux/issues/156
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Khalid Aziz <khalid@gonehiking.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
vmemdup_user is better than duplicating its implementation, So just replace
the open code.
The issue is detected with the help of Coccinelle.
Tested-by: Don Brace <don.brace@microsemi.com>
Acked-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Version bump conflict in batman-adv, take what's in net-next.
iavf conflict, adjustment of netdev_ops in net-next conflicting
with poll controller method removal in net.
Signed-off-by: David S. Miller <davem@davemloft.net>
When sd_init_command() get's a command with a unknown req_op() it crashes the
system via BUG().
This makes debugging the actual reason for the broken request cmd_flags pretty
hard as the system is down before it's able to write out debugging data on the
serial console or the trace buffer.
Change the BUG() to a WARN_ON() and return BLKPREP_KILL to fail gracefully and
return an I/O error to the producer of the request.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: Christoph Hellwig <hch@lst.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While dlpar adding primary ipr adapter back, driver goes through adapter
initialization then schedule ipr_worker_thread to start te disk scan by
dropping the host lock, calling scsi_add_device. Then get the adapter reset
request again, so driver does scsi_block_requests, this will cause the
scsi_add_device get hung until we unblock. But we can't run ipr_worker_thread
to do the unblock because its stuck in scsi_add_device.
This patch fixes the issue.
[mkp: typo and whitespace fixes]
Signed-off-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Clang warns when multiple pairs of parentheses are used for a single
conditional statement.
drivers/scsi/advansys.c:6451:20: warning: equality comparison with
extraneous parentheses [-Wparentheses-equality]
if ((sdtr_data == 0xFF)) {
~~~~~~~~~~^~~~~~~
drivers/scsi/advansys.c:6451:20: note: remove extraneous parentheses
around the comparison to silence this warning
if ((sdtr_data == 0xFF)) {
~ ^ ~
drivers/scsi/advansys.c:6451:20: note: use '=' to turn this equality
comparison into an assignment
if ((sdtr_data == 0xFF)) {
^~
=
1 warning generated.
Link: https://github.com/ClangBuiltLinux/linux/issues/155
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver currently uses the ndlp to get the local rport which is then used
to get the nvme transport remoteport pointer. There can be cases where a stale
remoteport pointer is obtained as synchronization isn't done through the
different dereferences.
Correct by using locks to synchronize the dereferences.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
blk-mq does not support runtime pm, so disable blk-mq support for now.
Fixes: d5038a13ec ("scsi: core: switch to scsi-mq by default")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/qla2xxx/qla_iocb.c: In function 'qla24xx_els_dcmd2_iocb':
drivers/scsi/qla2xxx/qla_iocb.c:2644:13: warning:
variable 'ptr_dma' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/lpfc/lpfc_nvme.c: In function 'lpfc_new_nvme_buf':
drivers/scsi/lpfc/lpfc_nvme.c:2238:24: warning:
variable 'sgl_size' set but not used [-Wunused-but-set-variable]
int bcnt, num_posted, sgl_size;
^
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently a scsi device won't contribute to kernel randomness when it uses
blk-mq. Since we commonly use scsi on rotational device with blk-mq, it make
sense to keep contributing to kernel randomness in these cases. This is
especially important for virtual machines.
commit b5b6e8c8d3 ("scsi: virtio_scsi: fix IO hang caused by automatic irq
vector affinity") made all virtio-scsi device to use blk-mq, which does not
contribute to randomness today. So for a virtual machine only having
virtio-scsi disk (which is common), it will simple stop getting randomness
from its disks in today's implementation.
With this patch, if the above VM has rotational virtio-scsi device, then it
can still benefit from the entropy generated from the disk.
Reported-by: Xuewei Zhang <xueweiz@google.com>
Signed-off-by: Xuewei Zhang <xueweiz@google.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Maciej Żenczykowski <maze@google.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/bnx2fc/bnx2fc_fcoe.c: In function 'bnx2fc_rcv':
drivers/scsi/bnx2fc/bnx2fc_fcoe.c:435:17: warning:
variable 'oxid' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While reviewing another part of the code, Kees noticed that the strncpy of the
partition name might not always be NUL terminated. Switch to using strscpy
which does this safely.
Reported-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Laura Abbott <labbott@redhat.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There's currently a warning about string overflow with strncat:
drivers/scsi/ibmvscsi_tgt/ibmvscsi_tgt.c: In function 'ibmvscsis_probe':
drivers/scsi/ibmvscsi_tgt/ibmvscsi_tgt.c:3479:2: error: 'strncat' specified
bound 64 equals destination size [-Werror=stringop-overflow=]
strncat(vscsi->eye, vdev->name, MAX_EYE);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Switch to a single snprintf instead of a strcpy + strcat to handle this
cleanly.
Signed-off-by: Laura Abbott <labbott@redhat.com>
Suggested-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
BUG_ON() already contains an unlikely(), there is no need for another one.
Signed-off-by: Igor Stoppa <igor.stoppa@huawei.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: "James E.J. Bottomley" <jejb@linux.vnet.ibm.com>
Cc: linux-scsi@vger.kernel.org
CC: linux-kernel@vger.kernel.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/aic7xxx/aic79xx_pci.c: In function 'ahd_pci_config':
drivers/scsi/aic7xxx/aic79xx_pci.c:291:19: warning:
variable 'shared_scb_data' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/pm8001/pm80xx_hwi.c: In function 'pm8001_set_phy_profile':
drivers/scsi/pm8001/pm80xx_hwi.c:4679:6: warning:
variable 'page_code' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/pm8001/pm8001_sas.c: In function 'pm8001_I_T_nexus_event_handler':
drivers/scsi/pm8001/pm8001_sas.c:1052:6: warning:
variable 'device_id' set but not used [-Wunused-but-set-variable]
drivers/scsi/pm8001/pm8001_sas.c: In function 'pm8001_abort_task':
drivers/scsi/pm8001/pm8001_sas.c:1191:6: warning:
variable 'device_id' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Error paths in ufshcd_init() ufshcd_hba_exit() killed clk_scaling workqueue
when the workqueue is actually created quite late in ufshcd_init(). So, we
end up getting NULL pointer dereference in such error paths. Fix this by
moving clk_scaling initialization and kill codes to two separate methods, and
call them at required places.
Fixes: 401f1e4490 ("scsi: ufs: don't suspend clock scaling during clock
gating")
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Subhash Jadavani <subhashj@codeaurora.org>
Cc: Matthias Kaehlcke <mka@chromium.org>
Cc: Evan Green <evgreen@chromium.org>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The fib6_info reference in rt6_info is rcu protected. Add a helper
to extract prefsrc from and update cxgbi_check_route6 to use it.
Fixes: 0153167aeb ("net/ipv6: Remove rt6i_prefsrc")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Updated the driver version from 0.1.38 to 0.1.39.
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When the firmware is not responding, execution of kexec boot causes a system
hang. When firmware assertion happened, driver get notified with interrupt
vector updated in MPI configuration table. Then, the driver will read
scratchpad register and set controller_fatal_error flag to true.
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For the function dma_unmap_sg(), the <nents> parameter should be number of
elements in the scatter list prior to the mapping, not after the mapping.
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Added proper mask for phy id in mpi_phy_stop_resp().
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Trivial fix to typo in debug message text.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We should first do the le16_to_cpu endian conversion and then apply the
FCP_CMD_LENGTH_MASK mask.
Fixes: 5f35509db1 ("qla2xxx: Terminate exchange if corrupted")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Quinn Tran <Quinn.Tran@cavium.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Variable num_chip_names is defined but not used, hence it is redundant and can
be removed.
Cleans up clang warning:
'num_chip_names' defined but not used [-Wunused-const-variable=]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/libfc/fc_fcp.c: In function 'fc_queuecommand':
drivers/scsi/libfc/fc_fcp.c:1875:30: warning:
variable 'rpriv' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
sym_int_sir() in sym_hipd.c does not check the command pointer for NULL before
using it in debug message prints.
Suggested-by: Matthew Wilcox <matthew.wilcox@oracle.com>
Signed-off-by: George Kennedy <george.kennedy@oracle.com>
Reviewed-by: Mark Kanda <mark.kanda@oracle.com>
Acked-by: Matthew Wilcox <matthew.wilcox@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update the driver version to 12.0.0.7
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds the ability to read firmware logs from the adapter. The driver
registers a buffer with the adapter that is then written to by the adapter.
The adapter posts CQEs to indicate content updates in the buffer. While the
adapter is writing to the buffer in a circular fashion, an application will
poll the driver to read the next amount of log data from the buffer.
Driver log buffer size is configurable via the ras_fwlog_buffsize sysfs
attribute. Verbosity to be used by firmware when logging to host memory is
controlled through the ras_fwlog_level attribute. The ras_fwlog_func
attribute enables or disables loggy by firmware.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, on each io completion, the stats update routine indiscriminately
holds a lock. While holding the adapter-wide lock, checks are made to check
whether status are being tracked. When disabled (the default), the locking
wasted a lot of cycles.
Check for stats enablement before taking the lock.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Message 6408 is displayed for each entry in an array, but the cpu and queue
numbers were incorrect for the entry. Message 6001 includes an extraneous
character.
Resolve both issues
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During attachment, the driver writes the EQ doorbell to disable potential
interrupts from an EQ. The current EQ doorbell format used for clearing the
interrupt is incorrect and uses an if_type=2 format, making the operation act
on the wrong EQ.
Correct the code to use the proper if_type=6 EQ doorbell format.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When taking the board offline while performing i/o, unsafe locking errors
occurred and irq level isn't properly managed.
In lpfc_sli_hba_down, spin_lock_irqsave(&phba->hbalock, flags) does not
disable softirqs raised from timer expiry. It is possible that a softirq is
raised from the lpfc_els_retry_delay routine and recursively requests the same
phba->hbalock spinlock causing deadlock.
Address the deadlocks by creating a new port_list lock. The softirq behavior
can then be managed a level deeper into the calling sequences.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When running an mds diagnostic that passes frames with the switch, soft
lockups are detected. The driver is in a CQE processing loop and has
sufficient amount of traffic that it never exits the ring processing routine,
thus the "lockup".
Cap the number of elements in the work processing routine to 64 elements. This
ensures that the cpu will be given up and the handler reschedule to process
additional items.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On io completion, the driver is taking an adapter wide lock and nulling the
scsi command back pointer. The nulling of the back pointer is to signify the
io was completed and the scsi_done() routine was called. However, the routine
makes no check to see if the abort routine had done the same thing and
possibly nulled the pointer. Thus it may doubly-complete the io.
Make the following mods:
- Check to make sure forward progress (call scsi_done()) only happens if the
command pointer was non-null.
- As the taking of the lock, which is adapter wide, is very costly on a system
under load, null the pointer using an xchg operation rather than under lock.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When nvme is enabled, change the default for two parameters:
sg_seg_cnt - raise the per-io sg list size so that 1MB ios are
supported (based on a 4k buffer per element).
iocb_cnt - raise the number of buffers used for things like
NVME LS request/responses to allow more concurrent requests
to for larger nvme configs.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver allocates a sg list per io struture based on a fixed maximum
size. When it registers with the protocol transports and indicates the max sg
list size it supports, the driver manipulates the fixed value to report a
lesser amount so that it has reserved space for sg elements that are used for
DIF.
The driver initialization path sets the cfg_sg_seg_cnt field to the
manipulated value for scsi. NVME initialization ran afterward and capped it's
maximum by the manipulated value for SCSI. This erroneously made NVME report
the SCSI-reduce-for-DIF value that reduced the max io size for nvme and wasted
sg elements.
Rework the driver so that cfg_sg_seg_cnt becomes the overall maximum size and
allow the max size to be tunable. A separate (new) scsi sg count is then
setup with the scsi-modified reduced value. NVME then initializes based off
the overall maximum.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver only sends NVME PRLI to a device that also supports FCP. This resuls
in remote ports that don't have fc_remote_ports created for them. The driver
is clearing the nlp_fc4_type for a ndlp at the wrong time.
Fix by moving the nlp_fc4_type clearing to the discovery engine in the
DEVICE_RECOVERY state. Also ensure that rport registration is done for all
nlp_fc4_types.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch fixes issue when switch command fails, current code increments
retry count twice. This results in a smaller number of retries.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Current code relies on switch to provide a unique combination of WWPN +
NPORTID to tract an FC port. This patch tries to detect a case where switch
data base can get corrupted where multiple WWPNs can have the same Nport ID.
The 1st Nport ID on the list will be kept while the duplicate Nport ID will be
discarded.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When qla2xxx and Target Core gets out of sync during command cleanup, qla2xxx
will not free command until it is out of firmware's hand and Target Core has
called the release on the command.
This patch adds synchronization using cmd_lock and release flag. If the
release flag is set, then qla2xxx will free up the command using
qlt_free_cmd() otherwise transport_generic_free_cmd() will be responsible for
relase of the command.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If chip unable to fully initialize, use full shutdown sequence to clear out
any stale FW state.
Fixes: e315cd28b9 ("[SCSI] qla2xxx: Code changes for qla data structure refactoring")
Cc: stable@vger.kernel.org #4.10
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On PLOGI complete + RSCN received, driver tries to handle RSCN but failed to
reset the session back to the beginning to restart the login process. Instead
the session was left in the Plogi complete without moving forward. This patch
will push the session state back to the delete state and restart the
connection.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Task abort can take 2 paths: 1) serial/synchronous abort where the calling
thread will put to sleep, wait for completion and free cmd resource. 2) async
abort where the cmd free will be free by the completion thread. For path 2,
driver is freeing the SRB too early.
Fixes: f6145e86d2 ("scsi: qla2xxx: Fix race between switch cmd completion and timeout")
Cc: stable@vger.kernel.org # 4.19
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add ability to allow each physical port to control operating mode. Current
code forces all ports to behave in one mode (i.e. initiator, target or
dual). This patch allows user to select the operating mode for each port.
- Driver must be loaded in dual mode to allow resource allocation
modprobe qla2xxx qlini_mode=dual
- In addition user can make adjustment to exchange resources using following
command
echo 1024 > /sys/class/scsi_host/host<x>/ql2xiniexchg
echo 1024 > /sys/class/scsi_host/host<x>/ql2xexchoffld
- trigger mode change and new setting of ql2xexchoffld|ql2xiniexchg
echo [<value>] > /sys/class/scsi_host/host<x>/qlini_mode
where, value can be one of following
- enabled
- disabled
- dual
- exclusive
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For Loop topology + Initiator, FW is in control of PLOGI/PRLI. When link is
reset, driver will try to cleanup the session by doing an Implicit Logout.
Instead, the code is doing an Explicit Logout. The explicit logout interferes
with FW state machine in trying to reconnect. The implicit logout was meant
for FW to flush commands. In loop, it is not needed because FW will auto
flush.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When FW rejects a command due to "entry_status" error (malform IOCB), the srb
resource needs to be returned back for cleanup. The filter to catch this is
in the wrong location.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Clear port speed value on chip reset.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During adapter shutdown process check for register disconnect before
proceeding to call PCI functions.
Signed-off-by: Sawan Chandak <sawan.chandak@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Abort IOCB request can take up to 40s or 2 ABTS timeout. We will wait for
ABTS response for 20s. On a timeout, second ABTS can go out with another 20s
timeout. On 2nd ABTS timeout FW will automatically do Logout.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch allows FC-NVMe under-run to be handled by transport
Signed-off-by: Darren Trapp <darren.trapp@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Current abort code defaults to legacy single queue where hardware_lock is used
to protect command search. This patch moves this code behind the QPair where
the qp_lock_ptr will reference the appropriate lock for either legacy/single
queue or MQ.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Using GPNFT/GNNFT command will be able to cover switch database with less
number of scans. This patch removes Get NportID with provided WWPN/GIDPN
switch command. By making this change, in large fabric with lots of remote
port or NPIV ports with noisy SAN, the number of GIDPN commands issued by a
port when it detects large number of remote ports going away or coming back,
can overwhelmn the switch and it can becomde unresponsive. In a case where the
fabric has not change, GIDPN is not required.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- Reduce sess_lock holding to prevent CPU Lock up. sess_lock was held across
fc_port registration and deletion. These calls can be blocked by upper
layer. Sess_lock is also being accessed by interrupt thread.
- Reduce number of loops in processing work_list to prevent kernel complaint
of CPU lockup or holding sess_lock.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, qla2x00_[get_sp|rel_sp] routines does {get|release} of srb
resource/srb_mempool directly from qla_hw_data. qla2x00_start_sp() is used to
issue management commands through the default Request Q 0 & Response Q 0 or
base_qpair. This patch moves access of these resources through
base_qpair. Instead of having knowledge of specific Q number and lock to
rsp/req queue, this change will key off the qpair that is assigned to the srb
resource. This lays the ground work for other routines to see this resource
through the qpair.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add sysfs support to control zio6 interrupt threshold. Using this sysfs hook
user can set when to generate interrupts. This value will be used to tell
firmware to generate interrupt at a certain interval. If the number of
exchanges/commands fall below defined setting, then the interrupt will be
generated immediately by the firmware.
By default ZIO6 will coalesce interrupts to a specified interval
regardless of low traffic or high traffic.
[mkp: fixed several typos]
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Following changes are added by this patch
- Prevent ABTS Response from getting in front of Termination of exchange.
Firmware requires driver to cleanup exchanges before ABTS response can be
sent. This reduces ABTS response error which triggers extra command
re-termination and re-sending of ABTS response.
- Add bits in driver and tracks CTIO/ATIO attribute bits for proper command
Termination. A copy of the ATTR bits will be kept in the ABTS task
management command as a back up copy, if an ABTS response encounters an
error.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
ABTS error completion can trigger an exchange cleanup from the driver and
another ABTS response will be generated. This retry of ABTS response can
cause loop between driver trying to send ABTS and firmware returning error.
This patch fixes this issue by adding logic to check for unresolved exchanges
and clean up before ABTS is retried. This patch also addes the fix to use the
same qpair as the ABTS completion for the terminatation of exchange as well as
retry of ABTS response.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When driver detect CTIO_INVALID_RX_ID status for CTIO, print message with
correct information to help with debugging.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Move ATIO queue processing out of hardware_lock to prevent deadlock.
Fixes: 3bb67df5b5 ("qla2xxx: Check for online flag instead of active reset when transmitting responses")
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For driver MBX submission, use mbox_busy to serialize request. For Userspace
MBX submission, use optrom mutex to serialize request.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When driver receive PLOGI/PRLI from FW, the WWPN value will be provided. If
it is not, then driver will terminate it. The WWPN allows driver to locate
the session or create a new session.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For target mode, any chip reset triggered before target mode is enabled will
be held off until user is ready to enable. This prevents the chip from
starting or running before it is intended.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When switch responds with error for Get Port Speed Command (GPSC), driver
should not proceed with telling FW about the speed of the remote port.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When all fabric scan retries fail, remove all RPorts, DMA resources for the
command. Otherwise we have stale Rports.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Turn ON logout_on_delete flag to make sure firmware resource for fcport is
cleaned up on ADISC error.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Turn off IOCB timeout timer on IOCB completion instead of turning it off in a
deferred task. This prevent false alarm if the deferred task is stalled out.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Decrement login retry count only for plogi instead of number of attempts made
for login.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, the rport registration is being called from a single work element
that is used to process QLA internal "work_list". This work_list is meant for
quick and simple task (ie no sleep). The Rport registration process sometime
can be delayed by upper layer. This causes back pressure with the internal
queue where other jobs are unable to move forward.
This patch will schedule the registration process with a new work element
(fc_port.reg_work). While the RPort is being registered, the current state of
the fcport will not move forward until the registration is done. If the state
of the fabric has changed, a new field/next_disc_state will record the next
action on whether to 'DELETE' or 'Reverify the session/ADISC'.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove redundant check for fcport is deleted or being delete. The same check
is already in the deletion routine.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Rename rscn_rcvd field to scan_needed to be more meaningful.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On Abort of initiator scsi command, the abort needs to follow the same qpair
as the the scsi command to prevent out of order processing.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch improves performance for 16G and above adapter by removing
additional call to process_response_queue().
[mkp: typo]
Cc: <stable@vger.kernel.org>
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After the conversion to fib6_info, rt6i_prefsrc has a single user that
reads the value and otherwise it is only set. The one reader can be
converted to use rt->from so rt6i_prefsrc can be removed, reducing
rt6_info by another 20 bytes.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bare-metal toolchains don't define __linux__, so aic7xxx build with
bare-metal toolchain is broken. This driver codebase used to be partially
shared with FreeBSD, but these days there is no point in keeping the
compatibility around. So let's just drop FreeBSD related code and get rid
of __linux__ checking in order to fix the build using bare-metal
toolchains.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
kmem_cache_destroy() can handle NULL pointer correctly, so there is no
need to check NULL pointer before calling kmem_cache_destroy()
Signed-off-by: Chengguang Xu <cgxu519@gmx.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Smatch complains about this code:
drivers/scsi/lpfc/lpfc_scsi.c:1053 lpfc_get_scsi_buf_s4()
warn: variable dereferenced before check 'lpfc_cmd' (see line 1039)
Fortunately the NULL check isn't required so I have removed it.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
'NEGOTIATION' was misspelled as 'NEGOTATION'. Fixed it. It is a coding
style change which should have no impact on runtime execution of code.
Signed-off-by: Faisal Mehmood <f.m3hm00d@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Variable dmsg is not being used and is redundant and hence can be
removed.
Cleans up clang warning:
warning: variable 'dmsg' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Variables dev and cpu are not being used and are redundant and hence can
be removed.
Cleans up clang warnings:
warning: variable 'dev' set but not used [-Wunused-but-set-variable]
warning: variable 'cpu' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
I ran into a new warning on randconfig kernels:
drivers/scsi/raid_class.c: In function 'raid_match':
drivers/scsi/raid_class.c:64:24: error: unused variable 'i' [-Werror=unused-variable]
This looks like a very old problem that for some reason was very hard to
run into, but it is very easy to fix, by replacing the incorrect #ifdef
with a simpler IS_ENABLED() check.
Fixes: fac829fdca ("[SCSI] raid_attrs: fix dependency problems")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The QED driver commit, 1ac4329a1c ("qed: Add configuration information
to register dump and debug data"), removes the CRC length validation
causing nvm_get_image failure while loading qedi driver:
[qed_mcp_get_nvm_image:2700(host_10-0)]Image [0] is too big - 00006008 bytes
where only 00006004 are available
[qedi_get_boot_info:2253]:10: Could not get NVM image. ret = -12
Hence add and adjust the CRC size to iSCSI NVM image to read boot info at
qedi load time.
Signed-off-by: Nilesh Javali <nilesh.javali@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The problem is that ->reset_state is a u8 but it can be set to -1 or -2 in
aac_tmf_callback() and the error handling in aac_eh_target_reset() relies
on it to be signed.
[mkp: fixed typo]
Fixes: 0d643ff3c3 ("scsi: aacraid: use aac_tmf_callback for reset fib")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This reverts commit 328728630d.
There is fundamental issue in commit 328728630d (scsi: core: avoid
host-wide host_busy counter for scsi_mq) because SCSI's host busy counter
may not be same with counter of blk-mq's inflight tags, especially in case
of none io scheduler.
We may switch to other approach for addressing this scsi_mq's performance
issue, such as percpu counter or kind of ways, so revert this commit first
for fixing this kind of issue in EH path, as reported by Jens.
Cc: Omar Sandoval <osandov@fb.com>,
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>,
Cc: James Bottomley <james.bottomley@hansenpartnership.com>,
Cc: Christoph Hellwig <hch@lst.de>,
Cc: Don Brace <don.brace@microsemi.com>
Cc: Kashyap Desai <kashyap.desai@broadcom.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Laurence Oberman <loberman@redhat.com>
Cc: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Jens Axboe <axboe@kernel.dk>
Reported-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This reverts commit 265d59aacb.
There is fundamental issue in commit 328728630d (scsi: core: avoid
host-wide host_busy counter for scsi_mq) because SCSI's host busy counter
may not be same with counter of blk-mq's inflight tags, especially in case
of none io scheduler.
So revert this commit first.
Cc: Omar Sandoval <osandov@fb.com>,
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>,
Cc: James Bottomley <james.bottomley@hansenpartnership.com>,
Cc: Christoph Hellwig <hch@lst.de>,
Cc: Don Brace <don.brace@microsemi.com>
Cc: Kashyap Desai <kashyap.desai@broadcom.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Laurence Oberman <loberman@redhat.com>
Cc: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Jens Axboe <axboe@kernel.dk>
Reported-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
e2c7b43 was supposed to limit transfer length to 1MB, but got the unit of
max_sectors wrong.
Fixes: e2c7b433f7 ("scsi: hpsa: limit transfer length to 1MB")
Signed-off-by: Martin Wilck <mwilck@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A recent change added some MDS processing in the lpfc_drain_txq routine
that relies on the fcp_wq being allocated. For nvmet operation the fcp_wq
is not allocated because it can only be an nvme-target. When the original
MDS support was added LS_MDS_LOOPBACK was defined wrong, (0x16) it should
have been 0x10 (decimal value used for hex setting). This incorrect value
allowed MDS_LOOPBACK to be set simultaneously with LS_NPIV_FAB_SUPPORTED,
causing the driver to crash when it accesses the non-existent fcp_wq.
Correct the bad value setting for LS_MDS_LOOPBACK.
Fixes: ae9e28f36a ("lpfc: Add MDS Diagnostic support.")
Cc: <stable@vger.kernel.org> # v4.12+
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Tested-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Change default behavior for fdmi registration to on.
[mkp: patch was mangled]
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- use be32_to_cpu() instead of ntohs() for 32 bit port capabilities.
- add a new function fwcaps32_to_caps16() to convert 32 bit port
capabilities to 16 bit port capabilities.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The default was changed, but the help text was not updated.
Fix grammar (s/the option/this option/) while at it.
[mkp: drop "new" as suggested by John Garry]
Fixes: d5038a13ec ("scsi: core: switch to scsi-mq by default")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pull IDA updates from Matthew Wilcox:
"A better IDA API:
id = ida_alloc(ida, GFP_xxx);
ida_free(ida, id);
rather than the cumbersome ida_simple_get(), ida_simple_remove().
The new IDA API is similar to ida_simple_get() but better named. The
internal restructuring of the IDA code removes the bitmap
preallocation nonsense.
I hope the net -200 lines of code is convincing"
* 'ida-4.19' of git://git.infradead.org/users/willy/linux-dax: (29 commits)
ida: Change ida_get_new_above to return the id
ida: Remove old API
test_ida: check_ida_destroy and check_ida_alloc
test_ida: Convert check_ida_conv to new API
test_ida: Move ida_check_max
test_ida: Move ida_check_leaf
idr-test: Convert ida_check_nomem to new API
ida: Start new test_ida module
target/iscsi: Allocate session IDs from an IDA
iscsi target: fix session creation failure handling
drm/vmwgfx: Convert to new IDA API
dmaengine: Convert to new IDA API
ppc: Convert vas ID allocation to new IDA API
media: Convert entity ID allocation to new IDA API
ppc: Convert mmu context allocation to new IDA API
Convert net_namespace to new IDA API
cb710: Convert to new IDA API
rsxx: Convert to new IDA API
osd: Convert to new IDA API
sd: Convert to new IDA API
...
Here is the bit set of char/misc drivers for 4.19-rc1
There is a lot here, much more than normal, seems like everyone is
writing new driver subsystems these days... Anyway, major things here
are:
- new FSI driver subsystem, yet-another-powerpc low-level
hardware bus
- gnss, finally an in-kernel GPS subsystem to try to tame all of
the crazy out-of-tree drivers that have been floating around
for years, combined with some really hacky userspace
implementations. This is only for GNSS receivers, but you
have to start somewhere, and this is great to see.
Other than that, there are new slimbus drivers, new coresight drivers,
new fpga drivers, and loads of DT bindings for all of these and existing
drivers.
Full details of everything is in the shortlog.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCW3g7ew8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykfBgCeOG0RkSI92XVZe0hs/QYFW9kk8JYAnRBf3Qpm
cvW7a+McOoKz/MGmEKsi
=TNfn
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the bit set of char/misc drivers for 4.19-rc1
There is a lot here, much more than normal, seems like everyone is
writing new driver subsystems these days... Anyway, major things here
are:
- new FSI driver subsystem, yet-another-powerpc low-level hardware
bus
- gnss, finally an in-kernel GPS subsystem to try to tame all of the
crazy out-of-tree drivers that have been floating around for years,
combined with some really hacky userspace implementations. This is
only for GNSS receivers, but you have to start somewhere, and this
is great to see.
Other than that, there are new slimbus drivers, new coresight drivers,
new fpga drivers, and loads of DT bindings for all of these and
existing drivers.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (255 commits)
android: binder: Rate-limit debug and userspace triggered err msgs
fsi: sbefifo: Bump max command length
fsi: scom: Fix NULL dereference
misc: mic: SCIF Fix scif_get_new_port() error handling
misc: cxl: changed asterisk position
genwqe: card_base: Use true and false for boolean values
misc: eeprom: assignment outside the if statement
uio: potential double frees if __uio_register_device() fails
eeprom: idt_89hpesx: clean up an error pointer vs NULL inconsistency
misc: ti-st: Fix memory leak in the error path of probe()
android: binder: Show extra_buffers_size in trace
firmware: vpd: Fix section enabled flag on vpd_section_destroy
platform: goldfish: Retire pdev_bus
goldfish: Use dedicated macros instead of manual bit shifting
goldfish: Add missing includes to goldfish.h
mux: adgs1408: new driver for Analog Devices ADGS1408/1409 mux
dt-bindings: mux: add adi,adgs1408
Drivers: hv: vmbus: Cleanup synic memory free path
Drivers: hv: vmbus: Remove use of slow_virt_to_phys()
Drivers: hv: vmbus: Reset the channel callback in vmbus_onoffer_rescind()
...
This is mostly updates to the usual drivers: mpt3sas, lpfc, qla2xxx,
hisi_sas, smartpqi, megaraid_sas, arcmsr. In addition, with the
continuing absence of Nic we have target updates for tcmu and target
core (all with reviews and acks). The biggest observable change is
going to be that we're (again) trying to switch to mulitqueue as the
default (a user can still override the setting on the kernel command
line). Other major core stuff is the removal of the remaining
Microchannel drivers, an update of the internal timers and some
reworks of completion and result handling.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCW3R3niYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishauRAP4yfBKK
dbxF81c/Bxi/Stk16FWkOOrjs4CizwmnMcpM5wD/UmM9o6ebDzaYpZgA8wIl7X/N
o/JckEZZpIp+5NySZNc=
=ggLB
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly updates to the usual drivers: mpt3sas, lpfc, qla2xxx,
hisi_sas, smartpqi, megaraid_sas, arcmsr.
In addition, with the continuing absence of Nic we have target updates
for tcmu and target core (all with reviews and acks).
The biggest observable change is going to be that we're (again) trying
to switch to mulitqueue as the default (a user can still override the
setting on the kernel command line).
Other major core stuff is the removal of the remaining Microchannel
drivers, an update of the internal timers and some reworks of
completion and result handling"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (203 commits)
scsi: core: use blk_mq_run_hw_queues in scsi_kick_queue
scsi: ufs: remove unnecessary query(DM) UPIU trace
scsi: qla2xxx: Fix issue reported by static checker for qla2x00_els_dcmd2_sp_done()
scsi: aacraid: Spelling fix in comment
scsi: mpt3sas: Fix calltrace observed while running IO & reset
scsi: aic94xx: fix an error code in aic94xx_init()
scsi: st: remove redundant pointer STbuffer
scsi: qla2xxx: Update driver version to 10.00.00.08-k
scsi: qla2xxx: Migrate NVME N2N handling into state machine
scsi: qla2xxx: Save frame payload size from ICB
scsi: qla2xxx: Fix stalled relogin
scsi: qla2xxx: Fix race between switch cmd completion and timeout
scsi: qla2xxx: Fix Management Server NPort handle reservation logic
scsi: qla2xxx: Flush mailbox commands on chip reset
scsi: qla2xxx: Fix unintended Logout
scsi: qla2xxx: Fix session state stuck in Get Port DB
scsi: qla2xxx: Fix redundant fc_rport registration
scsi: qla2xxx: Silent erroneous message
scsi: qla2xxx: Prevent sysfs access when chip is down
scsi: qla2xxx: Add longer window for chip reset
...
Nobody commented on this patch back in July. So now it gets merged.
* SCSI_IOCTL_SEND_COMMAND cleanup:
scsi sg: remove incorrect scsi command checking logic
-----BEGIN PGP SIGNATURE-----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=b9ib
-----END PGP SIGNATURE-----
Merge tag 'for-4.19/block-20180812' of git://git.kernel.dk/linux-block
Pull block updates from Jens Axboe:
"First pull request for this merge window, there will also be a
followup request with some stragglers.
This pull request contains:
- Fix for a thundering heard issue in the wbt block code (Anchal
Agarwal)
- A few NVMe pull requests:
* Improved tracepoints (Keith)
* Larger inline data support for RDMA (Steve Wise)
* RDMA setup/teardown fixes (Sagi)
* Effects log suppor for NVMe target (Chaitanya Kulkarni)
* Buffered IO suppor for NVMe target (Chaitanya Kulkarni)
* TP4004 (ANA) support (Christoph)
* Various NVMe fixes
- Block io-latency controller support. Much needed support for
properly containing block devices. (Josef)
- Series improving how we handle sense information on the stack
(Kees)
- Lightnvm fixes and updates/improvements (Mathias/Javier et al)
- Zoned device support for null_blk (Matias)
- AIX partition fixes (Mauricio Faria de Oliveira)
- DIF checksum code made generic (Max Gurtovoy)
- Add support for discard in iostats (Michael Callahan / Tejun)
- Set of updates for BFQ (Paolo)
- Removal of async write support for bsg (Christoph)
- Bio page dirtying and clone fixups (Christoph)
- Set of bcache fix/changes (via Coly)
- Series improving blk-mq queue setup/teardown speed (Ming)
- Series improving merging performance on blk-mq (Ming)
- Lots of other fixes and cleanups from a slew of folks"
* tag 'for-4.19/block-20180812' of git://git.kernel.dk/linux-block: (190 commits)
blkcg: Make blkg_root_lookup() work for queues in bypass mode
bcache: fix error setting writeback_rate through sysfs interface
null_blk: add lock drop/acquire annotation
Blk-throttle: reduce tail io latency when iops limit is enforced
block: paride: pd: mark expected switch fall-throughs
block: Ensure that a request queue is dissociated from the cgroup controller
block: Introduce blk_exit_queue()
blkcg: Introduce blkg_root_lookup()
block: Remove two superfluous #include directives
blk-mq: count the hctx as active before allocating tag
block: bvec_nr_vecs() returns value for wrong slab
bcache: trivial - remove tailing backslash in macro BTREE_FLAG
bcache: make the pr_err statement used for ENOENT only in sysfs_attatch section
bcache: set max writeback rate when I/O request is idle
bcache: add code comments for bset.c
bcache: fix mistaken comments in request.c
bcache: fix mistaken code comments in bcache.h
bcache: add a comment in super.c
bcache: avoid unncessary cache prefetch bch_btree_node_get()
bcache: display rate debug parameters to 0 when writeback is not running
...
Pull vfs open-related updates from Al Viro:
- "do we need fput() or put_filp()" rules are gone - it's always fput()
now. We keep track of that state where it belongs - in ->f_mode.
- int *opened mess killed - in finish_open(), in ->atomic_open()
instances and in fs/namei.c code around do_last()/lookup_open()/atomic_open().
- alloc_file() wrappers with saner calling conventions are introduced
(alloc_file_clone() and alloc_file_pseudo()); callers converted, with
much simplification.
- while we are at it, saner calling conventions for path_init() and
link_path_walk(), simplifying things inside fs/namei.c (both on
open-related paths and elsewhere).
* 'work.open3' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (40 commits)
few more cleanups of link_path_walk() callers
allow link_path_walk() to take ERR_PTR()
make path_init() unconditionally paired with terminate_walk()
document alloc_file() changes
make alloc_file() static
do_shmat(): grab shp->shm_file earlier, switch to alloc_file_clone()
new helper: alloc_file_clone()
create_pipe_files(): switch the first allocation to alloc_file_pseudo()
anon_inode_getfile(): switch to alloc_file_pseudo()
hugetlb_file_setup(): switch to alloc_file_pseudo()
ocxlflash_getfile(): switch to alloc_file_pseudo()
cxl_getfile(): switch to alloc_file_pseudo()
... and switch shmem_file_setup() to alloc_file_pseudo()
__shmem_file_setup(): reorder allocations
new wrapper: alloc_file_pseudo()
kill FILE_{CREATED,OPENED}
switch atomic_open() and lookup_open() to returning 0 in all success cases
document ->atomic_open() changes
->atomic_open(): return 0 in all success cases
get rid of 'opened' in path_openat() and the helpers downstream
...
Eight fixes. The most important one is the mpt3sas fix which makes
the driver work again on big endian systems. The rest are mostly
minor error path or checker issues and the vmw_scsi one fixes a
performance problem.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCW28FqCYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishRC9AP9sRmgl
MunaMCjubXaN2jkmyoga43ZckSVXz0wQUALI9gD+PE0At8vCbWx0tFTQLN5/QEtC
HsVMiAdHSZ87wF7ZQtw=
=ehub
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Eight fixes.
The most important one is the mpt3sas fix which makes the driver work
again on big endian systems. The rest are mostly minor error path or
checker issues and the vmw_scsi one fixes a performance problem"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: vmw_pvscsi: Return DID_RESET for status SAM_STAT_COMMAND_TERMINATED
scsi: sr: Avoid that opening a CD-ROM hangs with runtime power management enabled
scsi: mpt3sas: Swap I/O memory read value back to cpu endianness
scsi: fcoe: clear FC_RP_STARTED flags when receiving a LOGO
scsi: fcoe: drop frames in ELS LOGO error path
scsi: fcoe: fix use-after-free in fcoe_ctlr_els_send
scsi: qedi: Fix a potential buffer overflow
scsi: qla2xxx: Fix memory leak for allocating abort IOCB
We don't use blk-mq start/stop hw queue any more, so no reason to use
blk_mq_start_hw_queues which does clear_bit, replace it with
blk_mq_run_hw_queues.
Signed-off-by: Jianchao Wang <jianchao.w.wang@oracle.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch removes redundant trace that occurs when sending Device
Management(DM) request (fix behavior in commit 6667e6d91c ("scsi:
ufs: add trace event for ufs upiu").
Since the function send_command is called also for DM request, UPIU
trace for DM request is called twice- one identified as query_* the
other as send/complete.
Signed-off-by: Ohad Sharabi <ohad.sharabi@wdc.com>
Fixes: 6667e6d91c ("scsi: ufs: add trace event for ufs upiu")
Reviewed-by: Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch fixes following Smatch complaint:
drivers/scsi/qla2xxx/qla_iocb.c:2647 qla2x00_els_dcmd2_sp_done()
error: we previously assumed 'e' could be null (see line 2631)
Fixes: 8777e4314d ("scsi: qla2xxx: Migrate NVME N2N handling into state machine")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We accidentally return success instead of -ENOMEM on this error path.
Fixes: 2908d778ab ("[SCSI] aic94xx: new driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pointer STbuffer is being assigned but is never used hence it is redundant
and can be removed.
Cleans up clang warning:
warning: variable 'STbuffer' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Kai Mäkisara <kai.makisara@kolumbus.fi>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAltU8z0eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG5X8H/2fJr7m3k242+t76
sitwvx1eoPqTgryW59dRKm9IuXAGA+AjauvHzaz1QxomeQa50JghGWefD0eiJfkA
1AphQ/24EOiAbbVk084dAI/C2p122dE4D5Fy7CrfLnuouyrbFaZI5STbnrRct7sR
9deeYW0GDHO1Uenp4WDCj0baaqJqaevZ+7GG09DnWpya2nQtSkGBjqn6GpYmrfOU
mqFuxAX8mEOW6cwK16y/vYtnVjuuMAiZ63/OJ8AQ6d6ArGLwAsdn7f8Fn4I4tEr2
L0d3CRLUyegms4++Dmlu05k64buQu46WlPhjCZc5/Ts4kjrNxBuHejj2/jeSnUSt
vJJlibI=
=42a5
-----END PGP SIGNATURE-----
Merge tag 'v4.18-rc6' into for-4.19/block2
Pull in 4.18-rc6 to get the NVMe core AEN change to avoid a
merge conflict down the line.
Signed-of-by: Jens Axboe <axboe@kernel.dk>
Commands that are reset are returned with status
SAM_STAT_COMMAND_TERMINATED. PVSCSI currently returns DID_OK |
SAM_STAT_COMMAND_TERMINATED which fails the command. Instead, set hostbyte
to DID_RESET to allow upper layers to retry.
Tested by copying a large file between two pvscsi disks on same adapter
while performing a bus reset at 1-second intervals. Before fix, commands
sometimes fail with DID_OK. After fix, commands observed to fail with
DID_RESET.
Signed-off-by: Jim Gill <jgill@vmware.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Surround scsi_execute() calls with scsi_autopm_get_device() and
scsi_autopm_put_device(). Note: removing sr_mutex protection from the
scsi_cd_get() and scsi_cd_put() calls is safe because the purpose of
sr_mutex is to serialize cdrom_*() calls.
This patch avoids that complaints similar to the following appear in the
kernel log if runtime power management is enabled:
INFO: task systemd-udevd:650 blocked for more than 120 seconds.
Not tainted 4.18.0-rc7-dbg+ #1
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
systemd-udevd D28176 650 513 0x00000104
Call Trace:
__schedule+0x444/0xfe0
schedule+0x4e/0xe0
schedule_preempt_disabled+0x18/0x30
__mutex_lock+0x41c/0xc70
mutex_lock_nested+0x1b/0x20
__blkdev_get+0x106/0x970
blkdev_get+0x22c/0x5a0
blkdev_open+0xe9/0x100
do_dentry_open.isra.19+0x33e/0x570
vfs_open+0x7c/0xd0
path_openat+0x6e3/0x1120
do_filp_open+0x11c/0x1c0
do_sys_open+0x208/0x2d0
__x64_sys_openat+0x59/0x70
do_syscall_64+0x77/0x230
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Maurizio Lombardi <mlombard@redhat.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: <stable@vger.kernel.org>
Tested-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Swap the I/O memory read value back to cpu endianness before storing it in
a data structures which are defined in the MPI headers where u8 components
are not defined in the endianness order.
In this area from day one mpt3sas driver is using le32_to_cpu() &
cpu_to_le32() APIs. But in commit cf6bf9710c
(mpt3sas: Bug fix for big endian systems) we have removed these APIs
before reading I/O memory which we should haven't done it. So
in this patch I am correcting it by adding these APIs back
before accessing I/O memory.
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
To avoid introducing problems like those fixed in commit f7068114d4
("sr: pass down correctly sized SCSI sense buffer"), this creates a macro
wrapper for scsi_execute() that verifies the size of the sense buffer
similar to what was done for command string sizes in commit 3756f6401c
("exec: avoid gcc-8 warning for get_task_comm").
Another solution could be to add a length argument to scsi_execute(),
but this function already takes a lot of arguments and Jens was not fond
of that approach.
Additionally, this moves the SCSI_SENSE_BUFFERSIZE definition into
scsi_device.h, and removes a redundant include for scsi_device.h from
scsi_cmnd.h.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
There is a lot of needless struct request_sense usage in the CDROM
code. These can all be struct scsi_sense_hdr instead, to avoid any
confusion over their respective structure sizes. This patch is a lot
of noise changing "sense" to "sshdr", but the final code is more
readable to distinguish between "sense" meaning "struct request_sense"
and "sshdr" meaning "struct scsi_sense_hdr".
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Split scsi_common.o out of SCSI so that non-SCSI users can pull it in
easily for future sense buffer helper usage.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This removes the unused sense buffer in read_cap16() and write_same16().
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This patch fixes regression introduced for the N2N support for FC-NVMe. For
FC-NVMe with N2N connection, instead of FW initiating the Login, Driver
starts Login process. This patch migrates that new process from a
standalone path into existing session management state machine. With this
state change now driver will not wait for pull NPort ID from FW.
Fixes: edd05de197 ("scsi: qla2xxx: Changes to support N2N logins")
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Save frame payload size from init control block. This field/data is used
to register with switch database. This allows the init control block temp
buf to be reused.
[mkp: remove unused variable]
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch sets and clears FCF_ASYNC_{SENT|ACTIVE} flags to prevent
stalling of relogin attempt. Once flag are correctly set/cleared, relogin
timer can retry relogin attempt for driver to continue login.
Fixes: fa83e65885 ("scsi: qla2xxx: ensure async flags are reset correctly")
Cc: stable@vger.kernel.org #4.17
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix race condition between switch cmd completion and timeout timer. Timer
has popped triggers command free. On IOCB completion, stale sp point was
reused. Instead, an abort will be sent to FW to nudge the command out of FW
where the normal completion will take place.
RIP: 0010:qla2x00_chk_ms_status+0xf3/0x1b0 [qla2xxx]
Call Trace:
<IRQ>
qla24xx_els_ct_entry.isra.15+0x1d4/0x2b0 [qla2xxx]
qla24xx_msix_rsp_q+0x39/0xf0 [qla2xxx]
qla24xx_process_response_queue+0xbc/0x2b0 [qla2xxx]
qla24xx_msix_rsp_q+0x8a/0xf0 [qla2xxx]
__handle_irq_event_percpu+0xa0/0x1f0
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After selecting the NPort handle/loop_id, set a bit in the loop_id_map to
prevent others from selecting the same NPort handle.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Flush pending mailbox commands on chip reset. Wake up command that's
waiting for an interrupt and wait for mailbox counters to go to zero.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During normal IO, FW can return IO with 'port unavailble' status. Driver
would send a LOGO to remote port for session resync. On an off chance, a
PLOGI could arrive before sending the LOGO. This patch will skip sendiing
LOGO if a PLOGI just came in.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch sets discovery state back to GNL (Get Name List) when session is
stuck at GPDB (Get Port DataBase). This will allow state machine to retry
login and move session state ahead in discovery.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Prevent multiple registrations with transport layer for the same remote
port.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver uses shadow pointer instead of Mirror pointer for firmware dump
collection. Skip those entries for Mirror pointers for Request/Response
queue from firmware dump template reading.
Following messages are printed in log messages:
qla27xx_fwdt_entry_t268: unknown buffer 4
qla27xx_fwdt_entry_t268: unknown buffer 5
This patch fixes these error messages by adding skip_entry() to not read
them from template.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Prevent user from sending commands through sysfs while firmware is not
running or reset is in progress.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
qla2x00_reset_active only covers the window of turning the chip off. Add
check to cover turning chip on.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Login retry count was not properly decrementing which lead to endless
retry.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In case of N2N connect, sg_reset for bus/device/host was causing driver and
firmware state to go out of sync. This patch fixes this link instablity
when reconnect is attempted after link flap.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Variables scriptb0 and dp_sgmin are being assigned but are never used
hence they are redundant and can be removed.
Cleans up clang warnings:
warning: variable 'scriptb0' set but not used [-Wunused-but-set-variable]
warning: variable 'dp_sgmin' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- Updates csio_get_flash_params() to take care of ISSI, Macronix and
Winbond FLASH parts.
- Assume flash part size to be 4MB if it cannot be identified
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A long time ago the unfortunate decision was taken to add a self-deletion
attribute to the sysfs SCSI device directory. That decision was unfortunate
because self-deletion is really tricky. We can't drop that attribute
because widely used user space software depends on it, namely the
rescan-scsi-bus.sh script. Hence this patch that avoids that writing into
that attribute triggers a deadlock. See also commit 7973cbd9fbd9 ("[PATCH]
add sysfs attributes to scan and delete scsi_devices").
This patch avoids that self-removal triggers the following deadlock:
======================================================
WARNING: possible circular locking dependency detected
4.18.0-rc2-dbg+ #5 Not tainted
------------------------------------------------------
modprobe/6539 is trying to acquire lock:
000000008323c4cd (kn->count#202){++++}, at: kernfs_remove_by_name_ns+0x45/0x90
but task is already holding lock:
00000000a6ec2c69 (&shost->scan_mutex){+.+.}, at: scsi_remove_host+0x21/0x150 [scsi_mod]
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (&shost->scan_mutex){+.+.}:
__mutex_lock+0xfe/0xc70
mutex_lock_nested+0x1b/0x20
scsi_remove_device+0x26/0x40 [scsi_mod]
sdev_store_delete+0x27/0x30 [scsi_mod]
dev_attr_store+0x3e/0x50
sysfs_kf_write+0x87/0xa0
kernfs_fop_write+0x190/0x230
__vfs_write+0xd2/0x3b0
vfs_write+0x101/0x270
ksys_write+0xab/0x120
__x64_sys_write+0x43/0x50
do_syscall_64+0x77/0x230
entry_SYSCALL_64_after_hwframe+0x49/0xbe
-> #0 (kn->count#202){++++}:
lock_acquire+0xd2/0x260
__kernfs_remove+0x424/0x4a0
kernfs_remove_by_name_ns+0x45/0x90
remove_files.isra.1+0x3a/0x90
sysfs_remove_group+0x5c/0xc0
sysfs_remove_groups+0x39/0x60
device_remove_attrs+0x82/0xb0
device_del+0x251/0x580
__scsi_remove_device+0x19f/0x1d0 [scsi_mod]
scsi_forget_host+0x37/0xb0 [scsi_mod]
scsi_remove_host+0x9b/0x150 [scsi_mod]
sdebug_driver_remove+0x4b/0x150 [scsi_debug]
device_release_driver_internal+0x241/0x360
device_release_driver+0x12/0x20
bus_remove_device+0x1bc/0x290
device_del+0x259/0x580
device_unregister+0x1a/0x70
sdebug_remove_adapter+0x8b/0xf0 [scsi_debug]
scsi_debug_exit+0x76/0xe8 [scsi_debug]
__x64_sys_delete_module+0x1c1/0x280
do_syscall_64+0x77/0x230
entry_SYSCALL_64_after_hwframe+0x49/0xbe
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&shost->scan_mutex);
lock(kn->count#202);
lock(&shost->scan_mutex);
lock(kn->count#202);
*** DEADLOCK ***
2 locks held by modprobe/6539:
#0: 00000000efaf9298 (&dev->mutex){....}, at: device_release_driver_internal+0x68/0x360
#1: 00000000a6ec2c69 (&shost->scan_mutex){+.+.}, at: scsi_remove_host+0x21/0x150 [scsi_mod]
stack backtrace:
CPU: 10 PID: 6539 Comm: modprobe Not tainted 4.18.0-rc2-dbg+ #5
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.0.0-prebuilt.qemu-project.org 04/01/2014
Call Trace:
dump_stack+0xa4/0xf5
print_circular_bug.isra.34+0x213/0x221
__lock_acquire+0x1a7e/0x1b50
lock_acquire+0xd2/0x260
__kernfs_remove+0x424/0x4a0
kernfs_remove_by_name_ns+0x45/0x90
remove_files.isra.1+0x3a/0x90
sysfs_remove_group+0x5c/0xc0
sysfs_remove_groups+0x39/0x60
device_remove_attrs+0x82/0xb0
device_del+0x251/0x580
__scsi_remove_device+0x19f/0x1d0 [scsi_mod]
scsi_forget_host+0x37/0xb0 [scsi_mod]
scsi_remove_host+0x9b/0x150 [scsi_mod]
sdebug_driver_remove+0x4b/0x150 [scsi_debug]
device_release_driver_internal+0x241/0x360
device_release_driver+0x12/0x20
bus_remove_device+0x1bc/0x290
device_del+0x259/0x580
device_unregister+0x1a/0x70
sdebug_remove_adapter+0x8b/0xf0 [scsi_debug]
scsi_debug_exit+0x76/0xe8 [scsi_debug]
__x64_sys_delete_module+0x1c1/0x280
do_syscall_64+0x77/0x230
entry_SYSCALL_64_after_hwframe+0x49/0xbe
See also https://www.mail-archive.com/linux-scsi@vger.kernel.org/msg54525.html.
Fixes: ac0ece9174 ("scsi: use device_remove_file_self() instead of device_schedule_callback()")
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update the driver version to 12.0.0.6
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Enablement of the PBDE optimization brought out some incompatible behaviors
under error scenarios.
Best to disable and remove the PBDE optimization.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After memory allocation for the LCB response frame, the memory wasn't zero
initialized, and not all fields are set. Thus garbage shows up in the
payload.
Fix by zeroing the memory at allocation. Also properly set the Capability
field based on duration support.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Performance is affected when target queue depth is tracked. An atomic
counter is incremented on the submission path which competes with it being
decremented on the completion path. In addition, multiple CPUs can
simultaniously be manipulating this counter for the same ndlp.
Reduce the overhead by only performing the target increment/decrement when
the target queue depth is less than the overall adapter depth, thus is
actually meaningful.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During remote port loss fault testing, the driver crashed with the
following trace:
general protection fault: 0000 [#1] SMP
RIP: ... lpfc_nvme_register_port+0x250/0x480 [lpfc]
Call Trace:
lpfc_nlp_state_cleanup+0x1b3/0x7a0 [lpfc]
lpfc_nlp_set_state+0xa6/0x1d0 [lpfc]
lpfc_cmpl_prli_prli_issue+0x213/0x440
lpfc_disc_state_machine+0x7e/0x1e0 [lpfc]
lpfc_cmpl_els_prli+0x18a/0x200 [lpfc]
lpfc_sli_sp_handle_rspiocb+0x3b5/0x6f0 [lpfc]
lpfc_sli_handle_slow_ring_event_s4+0x161/0x240 [lpfc]
lpfc_work_done+0x948/0x14c0 [lpfc]
lpfc_do_work+0x16f/0x180 [lpfc]
kthread+0xc9/0xe0
ret_from_fork+0x55/0x80
After registering a new remoteport, the driver is pulling an ndlp pointer
from the lpfc rport associated with the private area of a newly registered
remoteport. The private area is uninitialized, so it's garbage.
Correct by pulling the the lpfc rport pointer from the entering ndlp point,
then ndlp value from at rport. Note the entering ndlp may be replacing by
the rport->ndlp due to an address change swap.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Enabling list_debug showed the drivers txcmplq was suffering list
corruption. The systems will eventually crash because the iocb free list
gets crossed linked with the prings txcmplq. Most systems will run for a
while after the corruption, but will eventually crash when a scsi eh reset
occurs and the txcmplq is attempted to be flushed. The flush gets stuck in
an endless loop.
The problem is the abort handler does not hold the sli4 ring lock while
validating the IO so the IO could complete while the driver is still
preping the abort. The erroneously generated abort, when it completes, has
pointers to the original IO that has already completed, and the IO
manipulation (for the second time) corrupts the list.
Correct by taking the ring lock early in the abort handler so the erroneous
abort won't be sent if the io has/is completing.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
CNA ports were showing speed as "unknown" even if the link is up.
Add speed decoding for FCOE-based adapters.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For ABORT_XRI_CN command, firmware identifies XRI to abort by IOTAG and RPI
combination. For ELS aborts, driver specifies IOTAG correctly but RPI is
not specified.
Fix by setting RPI in WQE.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When receiving a LOGO request we forget to clear the FC_RP_STARTED flag
before starting the rport delete routine.
As the started flag was not cleared, we're not deleting the rport but
waiting for a restart and thus are keeping the reference count of the rdata
object at 1.
This leads to the following kmemleak report:
unreferenced object 0xffff88006542aa00 (size 512):
comm "kworker/0:2", pid 24, jiffies 4294899222 (age 226.880s)
hex dump (first 32 bytes):
68 96 fe 65 00 88 ff ff 00 00 00 00 00 00 00 00 h..e............
01 00 00 00 08 00 00 00 02 c5 45 24 ac b8 00 10 ..........E$....
backtrace:
[<(____ptrval____)>] fcoe_ctlr_vn_add.isra.5+0x7f/0x770 [libfcoe]
[<(____ptrval____)>] fcoe_ctlr_vn_recv+0x12af/0x27f0 [libfcoe]
[<(____ptrval____)>] fcoe_ctlr_recv_work+0xd01/0x32f0 [libfcoe]
[<(____ptrval____)>] process_one_work+0x7ff/0x1420
[<(____ptrval____)>] worker_thread+0x87/0xef0
[<(____ptrval____)>] kthread+0x2db/0x390
[<(____ptrval____)>] ret_from_fork+0x35/0x40
[<(____ptrval____)>] 0xffffffffffffffff
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reported-by: ard <ard@kwaak.net>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
KASAN reports a use-after-free in fcoe_ctlr_els_send() when we're sending a
LOGO and have FIP debugging enabled. This is because we're first freeing
the skb and then printing the frame's DID. But the DID is a member of the
FC frame header which in turn is the skb's payload.
Exchange the debug print and kfree_skb() calls so we're not touching the
freed data.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This converts the drivers that called transport_deregister_session_configfs
and then immediately called transport_deregister_session to use
target_remove_session.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Chris Boot <bootc@bootc.net>
Cc: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Cc: Michael Cyr <mikecyr@linux.vnet.ibm.com>
Cc: <qla2xxx-upstream@qlogic.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Rename target_alloc_session to target_setup_session to avoid confusion with
the other transport session allocation function that only allocates the
session and because the target_alloc_session does so much more. It
allocates the session, sets up the nacl and registers the session.
The next patch will then add a remove function to match the setup in this
one, so it should make sense for all drivers, except iscsi, to just call
those 2 functions to setup and remove a session.
iscsi will continue to be the odd driver.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Chris Boot <bootc@bootc.net>
Cc: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Cc: Michael Cyr <mikecyr@linux.vnet.ibm.com>
Cc: <qla2xxx-upstream@qlogic.com>
Cc: Johannes Thumshirn <jth@kernel.org>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
