- Remove Xilinx AXI-PCIe host bridge arch dependency (Palmer Dabbelt)
* remotes/lorenzo/pci/controller/misc:
PCI/xilinx: Depend on OF instead of the ARCH
Merge L1 Terminal Fault fixes from Thomas Gleixner:
"L1TF, aka L1 Terminal Fault, is yet another speculative hardware
engineering trainwreck. It's a hardware vulnerability which allows
unprivileged speculative access to data which is available in the
Level 1 Data Cache when the page table entry controlling the virtual
address, which is used for the access, has the Present bit cleared or
other reserved bits set.
If an instruction accesses a virtual address for which the relevant
page table entry (PTE) has the Present bit cleared or other reserved
bits set, then speculative execution ignores the invalid PTE and loads
the referenced data if it is present in the Level 1 Data Cache, as if
the page referenced by the address bits in the PTE was still present
and accessible.
While this is a purely speculative mechanism and the instruction will
raise a page fault when it is retired eventually, the pure act of
loading the data and making it available to other speculative
instructions opens up the opportunity for side channel attacks to
unprivileged malicious code, similar to the Meltdown attack.
While Meltdown breaks the user space to kernel space protection, L1TF
allows to attack any physical memory address in the system and the
attack works across all protection domains. It allows an attack of SGX
and also works from inside virtual machines because the speculation
bypasses the extended page table (EPT) protection mechanism.
The assoicated CVEs are: CVE-2018-3615, CVE-2018-3620, CVE-2018-3646
The mitigations provided by this pull request include:
- Host side protection by inverting the upper address bits of a non
present page table entry so the entry points to uncacheable memory.
- Hypervisor protection by flushing L1 Data Cache on VMENTER.
- SMT (HyperThreading) control knobs, which allow to 'turn off' SMT
by offlining the sibling CPU threads. The knobs are available on
the kernel command line and at runtime via sysfs
- Control knobs for the hypervisor mitigation, related to L1D flush
and SMT control. The knobs are available on the kernel command line
and at runtime via sysfs
- Extensive documentation about L1TF including various degrees of
mitigations.
Thanks to all people who have contributed to this in various ways -
patches, review, testing, backporting - and the fruitful, sometimes
heated, but at the end constructive discussions.
There is work in progress to provide other forms of mitigations, which
might be less horrible performance wise for a particular kind of
workloads, but this is not yet ready for consumption due to their
complexity and limitations"
* 'l1tf-final' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (75 commits)
x86/microcode: Allow late microcode loading with SMT disabled
tools headers: Synchronise x86 cpufeatures.h for L1TF additions
x86/mm/kmmio: Make the tracer robust against L1TF
x86/mm/pat: Make set_memory_np() L1TF safe
x86/speculation/l1tf: Make pmd/pud_mknotpresent() invert
x86/speculation/l1tf: Invert all not present mappings
cpu/hotplug: Fix SMT supported evaluation
KVM: VMX: Tell the nested hypervisor to skip L1D flush on vmentry
x86/speculation: Use ARCH_CAPABILITIES to skip L1D flush on vmentry
x86/speculation: Simplify sysfs report of VMX L1TF vulnerability
Documentation/l1tf: Remove Yonah processors from not vulnerable list
x86/KVM/VMX: Don't set l1tf_flush_l1d from vmx_handle_external_intr()
x86/irq: Let interrupt handlers set kvm_cpu_l1tf_flush_l1d
x86: Don't include linux/irq.h from asm/hardirq.h
x86/KVM/VMX: Introduce per-host-cpu analogue of l1tf_flush_l1d
x86/irq: Demote irq_cpustat_t::__softirq_pending to u16
x86/KVM/VMX: Move the l1tf_flush_l1d test to vmx_l1d_flush()
x86/KVM/VMX: Replace 'vmx_l1d_flush_always' with 'vmx_l1d_flush_cond'
x86/KVM/VMX: Don't set l1tf_flush_l1d to true from vmx_l1d_flush()
cpu/hotplug: detect SMT disabled by BIOS
...
This comment has been there since the driver was introduced, but seems
to be a leftover from previous iterations of the driver. Indeed, we do
not lookup in a list to find the register ranges that matches the
given port/lane, as the "reg" property is in each sub-node
representing a PCI port. There is no lookup involved at all.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Rather than using the ARM-specific pci_common_init_dev() API, use the
pci_host_bridge logic directly.
Unfortunately, we can't use devm_of_pci_get_host_bridge_resources(),
because the DT binding for describing PCIe apertures for this PCI
controller is a bit special, and we cannot retrieve them from the
'ranges' property. Therefore, we still have some special code to
handle this.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Instead of hardcoding the remapping of IO_SPACE_LIMIT - SZ_64K, use
resource_size().
However, we cannot use just IO_SPACE_LIMIT, because pci_ioremap_io() has
a bug and doesn't allow remapping the last 64 KB before IO_SPACE_LIMIT,
so we ensure that we do not exceed this limit. When the pci_ioremap_io()
issue is fixed, this work around can be dropped.
Note that this workaround already existed, since we were mapping only
up to IO_SPACE_LIMIT - SZ_64K.
Suggested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
[lorenzo.pieralisi@arm.com: tweaked the commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
If there is no PCI I/O aperture configured in the Device Tree, it does
not make sense to create the virtual mapping for the PCI I/O space,
since we will anyway not create the MBus window that will allow to
access it. Therefore, do the pci_ioremap_io() only if necessary.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
pcie->realio.end should be the address of last byte of the area,
therefore using resource_size() of another resource is not correct, we
must substract 1 to get the address of the last byte.
Fixes: 11be65472a ("PCI: mvebu: Adapt to the new device tree layout")
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
This is already done earlier in mvebu_pcie_probe().
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
There isn't a hard dependency of the Xilinx AXI-PCIe host bridge on any
architecture. For example: at SiFive we map RISC-V cores to Xilinx FPGAs
and connect the Xilinx IP via a TileLink adapter, so the RISC-V Linux
port will need to be able to enable PCIE_XILINX in order to have PCIe
support.
This patch decouples the PCIE_XILINX support from ARCH. Instead it just
depends on OF, which is the only true dependency.
Signed-off-by: Palmer Dabbelt <palmer@dabbelt.com>
[hch: switch to OF instead of OF_PCI now that the latter is gone]
Signed-off-by: Christoph Hellwig <hch@lst.de>
[lorenzo.pieralisi@arm.com: trimmed the commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
The next patch in this series will have to make the definition of
irq_cpustat_t available to entering_irq().
Inclusion of asm/hardirq.h into asm/apic.h would cause circular header
dependencies like
asm/smp.h
asm/apic.h
asm/hardirq.h
linux/irq.h
linux/topology.h
linux/smp.h
asm/smp.h
or
linux/gfp.h
linux/mmzone.h
asm/mmzone.h
asm/mmzone_64.h
asm/smp.h
asm/apic.h
asm/hardirq.h
linux/irq.h
linux/irqdesc.h
linux/kobject.h
linux/sysfs.h
linux/kernfs.h
linux/idr.h
linux/gfp.h
and others.
This causes compilation errors because of the header guards becoming
effective in the second inclusion: symbols/macros that had been defined
before wouldn't be available to intermediate headers in the #include chain
anymore.
A possible workaround would be to move the definition of irq_cpustat_t
into its own header and include that from both, asm/hardirq.h and
asm/apic.h.
However, this wouldn't solve the real problem, namely asm/harirq.h
unnecessarily pulling in all the linux/irq.h cruft: nothing in
asm/hardirq.h itself requires it. Also, note that there are some other
archs, like e.g. arm64, which don't have that #include in their
asm/hardirq.h.
Remove the linux/irq.h #include from x86' asm/hardirq.h.
Fix resulting compilation errors by adding appropriate #includes to *.c
files as needed.
Note that some of these *.c files could be cleaned up a bit wrt. to their
set of #includes, but that should better be done from separate patches, if
at all.
Signed-off-by: Nicolai Stange <nstange@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
commit 9af6bcb11e ("PCI: mobiveil: Add Mobiveil PCIe Host Bridge IP
driver") did not add the configuration and build infrastructure to
configure and build the mobiveil controller driver, so at present the
driver code is in the kernel but cannot be compiled.
Add the mobiveil controller driver Kconfig/Makefile infrastructure.
Fixes: 9af6bcb11e ("PCI: mobiveil: Add Mobiveil PCIe Host Bridge IP
driver")
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Subrahmanya Lingappa <l.subrahmanya@mobiveil.co.in>
PCI mobiveil host controller driver currently fails to compile
with the following error:
drivers/pci/controller/pcie-mobiveil.c: In function
'mobiveil_pcie_probe':
drivers/pci/controller/pcie-mobiveil.c:788:8: error: implicit
declaration of function 'devm_of_pci_get_host_bridge_resources'; did you
mean 'pci_get_host_bridge_device'?
[-Werror=implicit-function-declaration]
ret = devm_of_pci_get_host_bridge_resources(dev, 0, 0xff,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
pci_get_host_bridge_device
Add the missing include file to pull in the required function declaration.
Fixes: 9af6bcb11e ("PCI: mobiveil: Add Mobiveil PCIe Host Bridge IP
driver")
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Subrahmanya Lingappa <l.subrahmanya@mobiveil.co.in>
The field pcie_reg_base in struct mobiveil_pcie represents a physical
address so it should be of phys_addr_t type rather than void __iomem*;
this results in the following compilation warnings:
drivers/pci/controller/pcie-mobiveil.c: In function
'mobiveil_pcie_parse_dt':
drivers/pci/controller/pcie-mobiveil.c:326:22: warning: assignment makes
pointer from integer without a cast [-Wint-conversion]
pcie->pcie_reg_base = res->start;
^
drivers/pci/controller/pcie-mobiveil.c: In function
'mobiveil_pcie_enable_msi':
drivers/pci/controller/pcie-mobiveil.c:485:25: warning: initialization
makes integer from pointer without a cast [-Wint-conversion]
phys_addr_t msg_addr = pcie->pcie_reg_base;
^~~~
drivers/pci/controller/pcie-mobiveil.c: In function
'mobiveil_compose_msi_msg':
drivers/pci/controller/pcie-mobiveil.c:640:21: warning: initialization
makes integer from pointer without a cast [-Wint-conversion]
phys_addr_t addr = pcie->pcie_reg_base + (data->hwirq * sizeof(int));
Fix the type and with it the compilation warnings.
Fixes: 9af6bcb11e ("PCI: mobiveil: Add Mobiveil PCIe Host Bridge IP
driver")
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Subrahmanya Lingappa <l.subrahmanya@mobiveil.co.in>
IB_WIN_SIZE is larger than INT_MAX so we need to cast it to u64.
Fixes: 9af6bcb11e ("PCI: mobiveil: Add Mobiveil PCIe Host Bridge IP driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
IB_WIN_SIZE is larger than INT_MAX so we need to cast it to u64.
Fixes: 9af6bcb11e ("PCI: mobiveil: Add Mobiveil PCIe Host Bridge IP driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Add MSI-X support and update driver documentation accordingly.
Signed-off-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Currently DesignWare IP does not handle legacy interrupts.
Add a legacy interrupt callback handler.
Signed-off-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Remove duplicate defines located on pcie-designware.h file already
available on /include/uapi/linux/pci-regs.h file.
Signed-off-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Add PCIe config space capability search function.
Add sysfs set/get interface to allow the change of EP MSI-X maximum number.
Add EP MSI-X callback for triggering interruptions.
Signed-off-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Change {cdns, dra7xx, artpec6, dw, rockchip}_pcie_ep_raise_irq() and
pci_epc_raise_irq() signature, namely the interrupt_num variable type
from u8 to u16 to accommodate 2048 maximum MSI-X interrupts.
Signed-off-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Alan Douglas <adouglas@cadence.com>
Acked-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Joao Pinto <jpinto@synopsys.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Move specific features settings from EP shared code
(pcie-designware-ep.c) to the driver (pcie-designware-plat.c).
Previous implementation disables the EP link notification
by default for all SoCs that uses EP DesignWare IP, which affects
directly the dra7xx and artpec6 SoCs.
Signed-off-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Variable mmc is being assigned but is never used hence it is redundant
and can be removed.
Cleans up clang warning:
warning: variable 'mmc' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
[lorenzo.pieralisi@arm.com: reworked commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Alan Douglas <adouglas@cadence.com>
Function dw_pcie_host_init() already initializes the root_bus_nr field
of 'struct pcie_port', so the -1 assignment prior to calling
dw_pcie_host_init() in platform specific driver is not really needed.
Drop it.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Pratyush Anand <pratyush.anand@gmail.com>
Function dw_pcie_host_init() already initializes the root_bus_nr field
of 'struct pcie_port', so the -1 assignment prior to calling
dw_pcie_host_init() in platform specific driver is not really needed.
Drop it.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Function dw_pcie_host_init() already initializes the root_bus_nr field
of 'struct pcie_port', so the -1 assignment prior to calling
dw_pcie_host_init() in platform specific driver is not really needed.
Drop it.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jianguo Sun <sunjianguo1@huawei.com>
Function dw_pcie_host_init() already initializes the root_bus_nr field
of 'struct pcie_port', so the -1 assignment prior to calling
dw_pcie_host_init() in platform specific driver is not really needed.
Drop it.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Joao Pinto <Joao.Pinto@synopsys.com>
Function dw_pcie_host_init() already initializes the root_bus_nr field
of 'struct pcie_port', so the -1 assignment prior to calling
dw_pcie_host_init() in platform specific driver is not really needed.
Drop it.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Function dw_pcie_host_init() already initializes the root_bus_nr field
of 'struct pcie_port', so the -1 assignment prior to calling
dw_pcie_host_init() in platform specific driver is not really needed.
Drop it.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Function dw_pcie_host_init() already initializes the root_bus_nr field
of 'struct pcie_port', so the -1 assignment prior to calling
dw_pcie_host_init() in platform specific driver is not really needed.
Drop it.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Function dw_pcie_host_init() already initializes the root_bus_nr field
of 'struct pcie_port', so the -1 assignment prior to calling
dw_pcie_host_init() in platform specific driver is not really needed.
Drop it.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Function dw_pcie_host_init() already initializes the root_bus_nr field
of 'struct pcie_port', so the -1 assignment prior to calling
dw_pcie_host_init() in platform specific driver is not really needed.
Drop it.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Reduce inbound/outbound mapping print level from dev_info() to
dev_dbg(). This reduces the console logs during Linux boot process.
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Oza Pawandeep <poza@codeaurora.org>
PAXC is an emulated PCIe root complex internally in various Broadcom
based SoCs. PAXC internally connects to the embedded network processor
within these SoCs, with the embedeed network processor exposed as an
endpoint device.
The number of physical functions from the embedded network processor
that can be accessed depends on the firmware configuration.
Unfortunately, due to an ASIC bug, unconfigured physical functions cannot
be properly hidden from the root complex during enumerattion. As a
result, config write access to these unconfigured physical functions
during enumeration will cause a bus lock up on the embedded network
processor.
Fortunately, these unconfigured physical functions contain a very
specific, staled PCIe device ID 0x168e. By making use of this device ID,
one is able to terminate the enumeration early in the vendor/device ID
config read.
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Oza Pawandeep <poza@codeaurora.org>
The internal MSI parsing logic in certain revisions of PAXC root
complexes does not work properly and can cause corruptions on the
writes transactions so they need to be disabled.
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Oza Pawandeep <poza@codeaurora.org>
On certain versions of Broadcom PAXC based root complexes, certain
regions of the configuration space are corrupted. As a result, it
prevents the Linux PCIe stack from traversing the linked list of the
capability registers completely and therefore the root complex is
not advertised as "PCIe capable". This prevents the correct PCIe RID
from being parsed in the kernel PCIe stack. A correct RID is required
for mapping to a stream ID from the SMMU or the device ID from the
GICv3 ITS.
This patch fixes up the issue by manually populating the related
PCIe capabilities.
Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Oza Pawandeep <poza@codeaurora.org>
Add shutdown callback to host driver which will disable PHY and
PM runtime.
Signed-off-by: Alan Douglas <adouglas@cadence.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
These PM ops will enable/disable the optional PHYs if present. The
AXI link-down register in the host driver is now cleared in
cdns_pci_map_bus() since the link-down bit will be set if the PHY has
been disabled. It is not cleared when enabling the PHY, since the
link will not yet be up (e.g. when an EP controller is connected
back-to-back to the host controller and its PHY is still disabled).
Link: http://lkml.kernel.org/r/1529915453-4633-5-git-send-email-adouglas@cadence.com
Signed-off-by: Alan Douglas <adouglas@cadence.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Add support for MSI to the kirin host controller driver, based
on the generic dwc infrastructure.
Signed-off-by: Xiaowei Song <songxiaowei@hisilicon.com>
Signed-off-by: Yao Chen <chenyao11@huawei.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
If PHYs are present, initialize and enable them at driver probe.
Signed-off-by: Alan Douglas <adouglas@cadence.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
cdns_pcie_writel() writes a long value; change the value parameter type
from u16 to u32 to rectify the function signature and related behaviour.
Signed-off-by: Alan Douglas <adouglas@cadence.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Commit de0aa7b2f9 ("PCI: hv: Fix 2 hang issues in hv_compose_msi_msg()")
uses local_bh_disable()/enable(), because hv_pci_onchannelcallback() can
also run in tasklet context as the channel event callback, so bottom halves
should be disabled to prevent a race condition.
With CONFIG_PROVE_LOCKING=y in the recent mainline, or old kernels that
don't have commit f71b74bca6 ("irq/softirqs: Use lockdep to assert IRQs
are disabled/enabled"), when the upper layer IRQ code calls
hv_compose_msi_msg() with local IRQs disabled, we'll see a warning at the
beginning of __local_bh_enable_ip():
IRQs not enabled as expected
WARNING: CPU: 0 PID: 408 at kernel/softirq.c:162 __local_bh_enable_ip
The warning exposes an issue in de0aa7b2f9: local_bh_enable() can
potentially call do_softirq(), which is not supposed to run when local IRQs
are disabled. Let's fix this by using local_irq_save()/restore() instead.
Note: hv_pci_onchannelcallback() is not a hot path because it's only called
when the PCI device is hot added and removed, which is infrequent.
Fixes: de0aa7b2f9 ("PCI: hv: Fix 2 hang issues in hv_compose_msi_msg()")
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Cc: stable@vger.kernel.org
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: K. Y. Srinivasan <kys@microsoft.com>
Part of advk_pcie_probe() is exactly an open-coded version of
pci_host_probe(). So instead of duplicating this code, use
pci_host_probe() directly.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
The PCIE I/O and MEM resource allocation mechanism is that root bus
goes through the following steps:
1. Check PCI bridges' range and computes I/O and Mem base/limits.
2. Sort all subordinate devices I/O and MEM resource requirements and
allocate the resources and writes/updates subordinate devices'
requirements to PCI bridges I/O and Mem MEM/limits registers.
Currently, PCI Aardvark driver only handles the second step and lacks
the first step, so there is an I/O and MEM resource allocation failure
when using a PCI switch. This commit fixes that by sizing bridges
before doing the resource allocation.
Fixes: 8c39d71036 ("PCI: aardvark: Add Aardvark PCI host controller
driver")
Signed-off-by: Zachary Zhang <zhangzg@marvell.com>
[Thomas: edit commit log.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: <stable@vger.kernel.org>
The call to of_get_next_child() returns a node pointer with refcount
incremented thus it must be explicitly decremented here in the error
path and after the last usage.
Fixes: d3c68e0a7e ("PCI: faraday: Add Faraday Technology FTPCI100 PCI Host Bridge driver")
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
The call to of_get_next_child() returns a node pointer with
refcount incremented thus it must be explicitly decremented
here after the last usage.
Fixes: ab597d35ef ("PCI: xilinx-nwl: Add support for Xilinx NWL PCIe Host Controller")
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The call to of_get_next_child() returns a node pointer with refcount
incremented thus it must be explicitly decremented here after the last
usage.
Fixes: 8961def568 ("PCI: xilinx: Add Xilinx AXI PCIe Host Bridge IP driver")
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
[lorenzo.pieralisi@arm.com: reworked commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
PCIE_DW_PLAT_HOST does not have any platform dependency, so it should
not default to yes.
Fixes: 1d906b2207 ("PCI: dwc: Add support for EP mode")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
If the Gen3 PHY fails to power up, the code does not undo the
initialization caused by phy_init(). Add the missing failure
handling to the rcar_pcie_phy_init_gen3() function.
Fixes: 517ca93a71 ("PCI: rcar: Add R-Car gen3 PHY support")
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Phil Edworthy <phil.edworthy@renesas.com>
Cc: Wolfram Sang <wsa@the-dreams.de>
If anything fails past phy_init_fn() and the system is a Gen3 with
a PHY, the PHY will be left on and inited. This is caused by the
phy_init_fn, which is in fact a pointer to rcar_pcie_phy_init_gen3()
function, which starts the PHY, yet has no counterpart in the failpath.
Add that counterpart.
Fixes: 517ca93a71 ("PCI: rcar: Add R-Car gen3 PHY support")
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Phil Edworthy <phil.edworthy@renesas.com>
Cc: Wolfram Sang <wsa@the-dreams.de>
new_pcichild_device() is not called in atomic context.
The call chain ending up at new_pcichild_device() is:
[1] new_pcichild_device() <- pci_devices_present_work()
pci_devices_present_work() is only set in INIT_WORK().
Despite never getting called from atomic context,
new_pcichild_device() calls kzalloc with GFP_ATOMIC,
which waits busily for allocation.
GFP_ATOMIC is not necessary and can be replaced with GFP_KERNEL
to avoid busy waiting.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
[lorenzo.pieralisi@arm.com: reworked commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Devices with slow interrupt handlers are significantly harming
performance when their interrupt vector is shared with a fast device.
Create a class code white list for devices with known fast interrupt
handlers and let all other devices share a single vector so that they
don't interfere with performance.
At the moment, only the NVM Express class code is on the list, but more
may be added if VMD users desire to use other low-latency devices in
these domains.
Signed-off-by: Keith Busch <keith.busch@intel.com>
[lorenzo.pieralisi@arm.com: changelog]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Jon Derrick: <jonathan.derrick@intel.com>
Outbound window is used to translate CPU space addresses to PCIe space
addresses when the CPU initiates PCIe transactions.
According to the suggestion of the HW designers, the recommended
solution is to use the default outbound parameters, even though the
current outbound window setting does not cause any known functional
issue.
This patch doesn't address any known functional issue, but aligns to
HW design guidelines, and removes code that isn't needed.
Signed-off-by: Evan Wang <xswang@marvell.com>
[Thomas: tweak commit log.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
[lorenzo.pieralisi@arm.com: handled host->controller dir move]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Victor Gu <xigu@marvell.com>
Reviewed-by: Nadav Haklai <nadavh@marvell.com>
In other to mimic other PCIe host controller drivers, introduce an
advk_pcie_valid_device() helper, used in the configuration read/write
functions.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
[lorenzo.pieralisi@arm.com: updated host->controller dir move]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Commit 51bc085d64 ("PCI: Improve host drivers compile test coverage")
added configuration options to allow PCI host controller drivers to be
compile tested on all architectures.
Some host controller drivers (eg PCIE_ALTERA) config entries select the
PCI_DOMAINS config option to enable PCI domains management in the kernel.
Now that host controller drivers can be compiled on all architectures, this
triggers build regressions on arches that do not implement the PCI_DOMAINS
required API (ie pci_domain_nr()):
drivers/ata/pata_ali.c: In function 'ali_init_chipset':
drivers/ata/pata_ali.c:469:38: error: implicit declaration of function 'pci_domain_nr'; did you mean 'pci_iomap_wc'?
Furthemore, some software configurations (ie Jailhouse) require a
PCI_DOMAINS enabled kernel to configure multiple host controllers without
having an explicit dependency on the ARM platform on which they run.
Make PCI_DOMAINS a visible configuration option on ARM so that software
configurations that need it can manually select it and move the PCI_DOMAINS
selection from PCI controllers configuration file to ARM sub-arch config
entries that currently require it, fixing the issue.
Fixes: 51bc085d64 ("PCI: Improve host drivers compile test coverage")
Link: https://lkml.kernel.org/r/20180612170229.GA10141@roeck-us.net
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Acked-by: Jan Kiszka <jan.kiszka@siemens.com>
Acked-by: Ley Foon Tan <ley.foon.tan@intel.com>
Acked-by: Rob Herring <robh@kernel.org>
Cc: Scott Branden <scott.branden@broadcom.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Guenter Roeck <linux@roeck-us.net>
- Additional struct_size() conversions (Matthew, Kees)
- Explicitly reported overflow fixes (Silvio, Kees)
- Add missing kvcalloc() function (Kees)
- Treewide conversions of allocators to use either 2-factor argument
variant when available, or array_size() and array3_size() as needed (Kees)
-----BEGIN PGP SIGNATURE-----
Comment: Kees Cook <kees@outflux.net>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=zUUp
-----END PGP SIGNATURE-----
Merge tag 'overflow-v4.18-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull more overflow updates from Kees Cook:
"The rest of the overflow changes for v4.18-rc1.
This includes the explicit overflow fixes from Silvio, further
struct_size() conversions from Matthew, and a bug fix from Dan.
But the bulk of it is the treewide conversions to use either the
2-factor argument allocators (e.g. kmalloc(a * b, ...) into
kmalloc_array(a, b, ...) or the array_size() macros (e.g. vmalloc(a *
b) into vmalloc(array_size(a, b)).
Coccinelle was fighting me on several fronts, so I've done a bunch of
manual whitespace updates in the patches as well.
Summary:
- Error path bug fix for overflow tests (Dan)
- Additional struct_size() conversions (Matthew, Kees)
- Explicitly reported overflow fixes (Silvio, Kees)
- Add missing kvcalloc() function (Kees)
- Treewide conversions of allocators to use either 2-factor argument
variant when available, or array_size() and array3_size() as needed
(Kees)"
* tag 'overflow-v4.18-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: (26 commits)
treewide: Use array_size in f2fs_kvzalloc()
treewide: Use array_size() in f2fs_kzalloc()
treewide: Use array_size() in f2fs_kmalloc()
treewide: Use array_size() in sock_kmalloc()
treewide: Use array_size() in kvzalloc_node()
treewide: Use array_size() in vzalloc_node()
treewide: Use array_size() in vzalloc()
treewide: Use array_size() in vmalloc()
treewide: devm_kzalloc() -> devm_kcalloc()
treewide: devm_kmalloc() -> devm_kmalloc_array()
treewide: kvzalloc() -> kvcalloc()
treewide: kvmalloc() -> kvmalloc_array()
treewide: kzalloc_node() -> kcalloc_node()
treewide: kzalloc() -> kcalloc()
treewide: kmalloc() -> kmalloc_array()
mm: Introduce kvcalloc()
video: uvesafb: Fix integer overflow in allocation
UBIFS: Fix potential integer overflow in allocation
leds: Use struct_size() in allocation
Convert intel uncore to struct_size
...
Native PCI drivers for root complex devices were originally all in
drivers/pci/host/. Some of these devices can also be operated in endpoint
mode. Drivers for endpoint mode didn't seem to fit in the "host"
directory, so we put both the root complex and endpoint drivers in
per-device directories, e.g., drivers/pci/dwc/, drivers/pci/cadence/, etc.
These per-device directories contain trivial Kconfig and Makefiles and
clutter drivers/pci/. Make a new drivers/pci/controllers/ directory and
collect all the device-specific drivers there.
No functional change intended.
Link: https://lkml.kernel.org/r/1520304202-232891-1-git-send-email-shawn.lin@rock-chips.com
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
