Describe the GPIO used to reset the Ethernet PHY for EthernetAVB.
This allows the driver to reset the PHY during probe and after system
resume.
On ULCB, the enable pin of the regulator providing PHY power is always
pulled high, but the driver may still need to reset the PHY if this
wasn't done by the bootloader before.
Inspired by patches in the BSP for the individual Salvator-X/XS boards
by Kazuya Mizuguchi.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe the GPIO used to reset the Ethernet PHY for EthernetAVB.
This allows the driver to reset the PHY during probe and after system
resume.
This fixes Ethernet operation after resume from s2ram on Salvator-XS,
where the enable pin of the regulator providing PHY power is connected
to PRESETn, and PSCI powers down the SoC during system suspend.
On Salvator-X, the enable pin is always pulled high, but the driver may
still need to reset the PHY if this wasn't done by the bootloader
before.
Inspired by patches in the BSP for the individual Salvator-X/XS boards
by Kazuya Mizuguchi.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Now that the commit 833bdb47c8 ("dt-bindings: power: add R8A77970 SYSC
power domain definitions") has hit Linus' tree, we can replace the bare
numbers (we had to use to avoid a cross tree dependency) with these macro
definitions...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Now that the commit ecadea00f5 ("dt-bindings: clock: Add R8A77970 CPG
core clock definitions") has hit Linus' tree, we can replace the bare
numbers (we had to use to avoid a cross tree dependency) with these macro
definitions...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the V3M Starter Kit board dependent part of the EtherAVB
device node.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the initial device tree for the V3M Starter Kit board.
The board has 1 debug serial port (SCIF0); include support for it,
so that the serial console can work.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add IPMMU-RT to the Ethernet-AVB device node.
Based on work by Magnus Damm for the r8a7795.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add r8a77995 IPMMU nodes and keep all disabled by default.
Based on work for the r8a7795 and r8a7796 by Magnus Damm
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Enable the r8a77970 device nodes for IPMMU-DS1, IPMMU-RT
and the shared IPMMU-MM device.
Based on work for the r8a7796 by Magnus Damm.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add IPMMU-RT to the Ethernet-AVB device node.
Based on work by Magnus Damm for the r8a7795.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Hook up r8a77970 DMAC nodes to the IPMMU. In particular
SYS-DMAC1 and SYS-DMAC2 get tied to IPMMU-DS1.
Based on work for the r8a7796 by Magnus Damm.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add r8a77970 IPMMU nodes and keep all disabled by default.
Based on work for the r8a7796 by Magnus Damm
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Sort includes used in r8a77970 DTS to improve maintainability
and for consistency with other R-Car DTS files.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch changes the number of GPIO bank 1 ports to 29 because GP-1-28
port pin of R8A7795 ES2.0 SoC support was added.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Fixes: 291e0c4994 ("arm64: dts: r8a7795: Add support for R-Car H3 ES2.0")
[geert: Keep 28 GPIOs on H3 ES1.x after r8a7795.dtsi sharing]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Adds CAN FD controller node for r8a77995.
Based on a patch for r8a7796 by Chris Paterson.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Adds CAN controller nodes for r8a77995.
Based on a patch for r8a7796 by Chris Paterson.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Adds external CAN clock node for r8a77995. This clock can be used as
fCAN clock of CAN and CAN FD controller.
Based on a patch for r8a7796 by Chris Paterson.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Document clearly which SoC this DTS applies to, to distinguish from
Salvator-XS boards equipped with other SoCs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Document clearly which SoC this DTS applies to, to distinguish from
Salvator-X boards equipped with other SoCs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Document clearly which SoC this DTS applies to, to distinguish from
Salvator-X boards equipped with other SoCs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Document clearly which SoC this DTS applies to, to distinguish from
Salvator-X boards equipped with other SoCs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the ROHM BD9571MWV PMIC.
This was based on the example in the DT binding documentation, but using
IRQ0 instead of a GPIO interrupt, as that matches the schematics, and
because INTC-EX is a simpler block.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable the r8a7795 device nodes for IPMMU-VI0, IPMMU-VP1, IPMMU-DS0,
IPMMU-DS1 and the shared IPMMU-MM device.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Enable the r8a7795 ES1.x device node for IPMMU-MP1.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add IPMMU-HC to the SATA device node.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add IPMMU-DS0 to the Ethernet-AVB device node.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Hook up the FCPVI devices to allow use of VSPI with IPMMU-VP.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Hook up the FCPVI devices to allow use of VSPI with
IPMMU-VP0 and IPMMU-VP1.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Hook up the FCPVB devices to allow use of VSPBC/VSPBD with
IPMMU-VP0 and IPMMU-VP1.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Hook up the FCPF devices to allow use of FDP1 with IPMMU-VP0.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Hook up the FCPF devices to allow use of FDP1 with IPMMU-VP.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Hook up the FCPVD devices to allow use of the VSP and DU
together with IPMMU-VI0.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Hook up the FCPVD devices to allow use of the VSP and DU
together with IPMMU-VI1 and IPMMU-VI1.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Hook up r8a7795 ES2.0 Audio-DMAC nodes to the IPMMU-MP0.
Hook up r8a7795 ES1.x Audio-DMAC nodes to the IPMMU-MP1.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Hook up r8a7795 SYS-DMAC nodes to the IPMMUs. In particular SYS-DMAC0 gets
tied to IPMMU-DS0, and SYS-DMAC1 and SYS-DMAC2 get tied to IPMMU-DS1.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add r8a7795 ES1.x IPMMU nodes and keep all disabled by default.
This is a follow-up to a patch that adds IPMMU device nodes that
are common to r8a7795 ES1.x and ES2.0
Power domains are omitted as they appear to be undocumented.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add r8a7795 IPMMU nodes and keep all disabled by default.
This includes all IPMMU devices for r8a7795 ES2.0. Those
not present in r8a7795 ES1.x are removed from the DT for those
SoCs using delete-node. A follow-up patch will add IPMMU devices
to ES1.x which are not also present in ES2.0.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
R-Car D3 has only one SDHI controller.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Differs from other Gen3 SoCs in that each controller only supports eight
channels.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
ULCB-KF has a USB2.0 dual-role channel (CN13).
This adds dr_mode property for USB2.0 channel 0 (EHCI/OHCI and HS-USB)
as "otg".
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This supports USB2 PHY channel #0 on ULCB Kingfisher board
The dedicated USB0_PWEN pin is used to control CN13 VBUS source from U43
power supply.
MAX3355 can also provide VBUS, hence it should be disabled via OTG_OFFVBUSn
node coming from gpio expander TCA9539.
Set MAX3355 enabled using OTG_EXTLPn node to be able to read OTG ID of
CN13.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable the r8a7795 device nodes for IPMMU-DS0, IPMMU-DS1, IPMMU-MP,
IPMMU-VI0, IPMMU-VC0 and the shared IPMMU-MM device.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add IPMMU-DS0 to the Ethernet-AVB device node.
Based on work by Magnus Damm for the r8a7795.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Hook up the FCPVI devices to allow use of VSPI with IPMMU-VC0.
Based on work for the r8a7795 by Magnus Damm.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Hook up the FCPF devices to allow use of FDP1 with IPMMU-VI0.
Based on work by Magnus Damm for the r8a7795.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Hook up r8a7796 Audio-DMAC nodes to the IPMMU-MP.
Based on work for the r8a7795 by Magnus Damm.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Hook up r8a7796 DMAC nodes to the IPMMUs. In particular SYS-DMAC0
gets tied to IPMMU-DS0, and SYS-DMAC1 and SYS-DMAC2 get tied to IPMMU-DS1.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add r8a7796 IPMMU nodes and keep all disabled by default.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
