B2260 board is the STMicroelectronics 96Board
based on STiH410 soc :
- 1GB DDR
- On-Board USB combo WiFi/Bluetooth RTL8723BU
with PCB soldered antenna
- Ethernet 1000-BaseT
- Sata
- HDMI
- 2 x USB2 type A
- micro USB2 type AB
- SD card slot
- High speed connector (SD/I2C/USB interfaces)
- Slow speed connector (UART/I2C/GPIO/SPI/PCM interfaces)
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Device tree contents continue to be the largest branches we submit. This
time around, some of the contents worth pointing out is:
- New SoC platforms:
- Freescale i.MX 7Solo
- Broadcom BCM23550
- Cirrus Logic EP7209 and EP7211 (clps711x platforms)_
- Hisilicon HI3519
- Renesas R8A7792
Some of the other delta that is sticking out, line-count wise:
- Exynos moves of IP blocks under an SoC bus, which causes a large delta due
to indentation changes
- A new Tegra K1 board: Apalis
- A bunch of small updates to many Allwinner platforms; new hardware support,
some cleanup, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=C4NU
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Olof Johansson:
"Device tree contents continue to be the largest branches we submit.
This time around, some of the contents worth pointing out is:
New SoC platforms:
- Freescale i.MX 7Solo
- Broadcom BCM23550
- Cirrus Logic EP7209 and EP7211 (clps711x platforms)_
- Hisilicon HI3519
- Renesas R8A7792
Some of the other delta that is sticking out, line-count wise:
- Exynos moves of IP blocks under an SoC bus, which causes a large
delta due to indentation changes
- a new Tegra K1 board: Apalis
- a bunch of small updates to many Allwinner platforms; new hardware
support, some cleanup, etc"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (426 commits)
ARM: dts: sun8i: Add dts file for inet86dz board
ARM: dts: sun8i: Add dts file for Polaroid MID2407PXE03 tablet
ARM: dts: sun8i: Use sun8i-reference-design-tablet for ga10h dts
ARM: dts: sun8i: Use sun8i-reference-design-tablet for polaroid mid2809pxe04
ARM: dts: sun8i: reference-design-tablet: Add drivevbus-supply
ARM: dts: Copy sun8i-q8-common.dtsi sun8i-reference-design-tablet.dtsi
ARM: dts: sun5i: Use sun5i-reference-design-tablet.dtsi for utoo p66 dts
ARM: dts: sun5i: Use sun5i-reference-design-tablet.dtsi for dit4350 dts
ARM: dts: sun5i: reference-design-tablet: Remove mention of q8
ARM: dts: sun5i: reference-design-tablet: Set lradc vref to avcc
ARM: dts: sun5i: Rename sun5i-q8-common.dtsi sun5i-reference-design-tablet.dtsi
ARM: dts: sun5i: Move q8 display bits to sun5i-a13-q8-tablet.dts
ARM: dts: sunxi: Rename sunxi-q8-common.dtsi sunxi-reference-design-tablet.dtsi
ARM: dts: at91: Don't build unnecessary dtbs
ARM: dts: at91: sama5d3x: separate motherboard gmac and emac definitions
ARM: dts: at91: at91sam9g25ek: fix isi endpoint node
ARM: dts: at91: move isi definition to at91sam9g25ek
ARM: dts: at91: fix i2c-gpio node name
ARM: dts: at91: vinco: fix regulator name
ARM: dts: at91: ariag25 : fix onewire node
...
Another set of changes for the 4.8 merge window, among which:
- Reworking of the DT for the tablets based on Allwinner reference design
and q8 designs to avoid duplication as much as possible
- Renaming a DT merged in the first PR for consistency
- Enable a few devices on some boards
- New boards: Polaroid MID2407PXE03, inet86dz
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=QU36
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-4.8-2-bis' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/dt
Merge "Allwinner DT changes for 4.8, take 2" from Maxime Ripard:
Another set of changes for the 4.8 merge window, among which:
- Reworking of the DT for the tablets based on Allwinner reference design
and q8 designs to avoid duplication as much as possible
- Renaming a DT merged in the first PR for consistency
- Enable a few devices on some boards
- New boards: Polaroid MID2407PXE03, inet86dz
* tag 'sunxi-dt-for-4.8-2-bis' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux: (21 commits)
ARM: dts: sun8i: Add dts file for inet86dz board
ARM: dts: sun8i: Add dts file for Polaroid MID2407PXE03 tablet
ARM: dts: sun8i: Use sun8i-reference-design-tablet for ga10h dts
ARM: dts: sun8i: Use sun8i-reference-design-tablet for polaroid mid2809pxe04
ARM: dts: sun8i: reference-design-tablet: Add drivevbus-supply
ARM: dts: Copy sun8i-q8-common.dtsi sun8i-reference-design-tablet.dtsi
ARM: dts: sun5i: Use sun5i-reference-design-tablet.dtsi for utoo p66 dts
ARM: dts: sun5i: Use sun5i-reference-design-tablet.dtsi for dit4350 dts
ARM: dts: sun5i: reference-design-tablet: Remove mention of q8
ARM: dts: sun5i: reference-design-tablet: Set lradc vref to avcc
ARM: dts: sun5i: Rename sun5i-q8-common.dtsi sun5i-reference-design-tablet.dtsi
ARM: dts: sun5i: Move q8 display bits to sun5i-a13-q8-tablet.dts
ARM: dts: sunxi: Rename sunxi-q8-common.dtsi sunxi-reference-design-tablet.dtsi
ARM: dts: sun7i: bananapi-m1-plus: red LED is power LED
ARM: dts: sun7i: bananapi-m1-plus: Unify suffix for board specific labels
ARM: dts: sun7i: bananapi-m1-plus: Reindent whole file using tabs
ARM: dts: sun7i: lamobo-r1: Enable audio codec
ARM: dts: sun7i: lamobo-r1: Fix GPIO flags in reg_ahci_5v
ARM: dts: sun8i-h3: Rename sinovoip-bpi-m2-plus to bananapi-m2-plus
ARM: dts: sun7i: lamobo-r1: Remove usb1 vbus regulator
...
The inet86dz board is a board used in 7" tablets from various oems.
These tablets are a23 based 7" tablets featuring a 1024x600 LCD,
512MB RAM, 4G NAND, rtl8188etv usb wifi, gsl1680 touchschreen,
micro-sd slot, 3.5mm headphone jack and a micro-usb otg connector
which doubles as charging port.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Polaroid MID2407PXE03 is an a23 based 7" tablet based on a M86_MB V2.0
PCB, featuring a 800x480 LCD, 512MB RAM, 4G NAND, esp8089 wifi, gsl1680
touchschreen, micro-sd slot, 3.5mm headphone jack and a micro-usb otg
connector which doubles as charging port.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Building both ARMv4 and ARMv5 dtbs when SOC_SAM_V4_V5 is an issue for
kernelci because it will then attempt to boot ARMv4 kernels on at91sam9
which doesn't work.
Use CONFIG_SOC_AT91RM9200 and CONFIG_SOC_AT91SAM9 instead.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Some cleanups to existing device tree sources and add Toradex Apalis TK1
support.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=h8a0
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.8-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt
Merge "ARM: tegra: Device tree changes for v4.8-rc1" from Thierry Reding:
Some cleanups to existing device tree sources and add Toradex Apalis TK1
support.
* tag 'tegra-for-4.8-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: Initial support for Apalis TK1
ARM: tegra: Remove commas from unit addresses on Tegra124
ARM: tegra: Import latest Jetson TK1 spreadsheet
ARM: tegra: Add spaces around = in properties
ARM: tegra: Fix a couple of DTC warnings
This patch adds the device tree to support Toradex Apalis TK1 a
computer on module which can be used on different carrier boards.
The module consists of a Tegra TK1 SoC, a PMIC solution, 2 GB of DDR3L
RAM, a bunch of level shifters, an eMMC, a TMP451 temperature sensor
chip, an I210 gigabit Ethernet controller and a SGTL5000 audio codec.
Furthermore, there is a Kinetis MK20DN512 companion micro controller for
analogue, CAN and resistive touch functionality which is not yet
supported. Anything that is not self contained on the module is disabled
by default.
The device tree for the Evaluation Board includes the module's device
tree and enables the supported peripherals of the carrier board (the
Evaluation Board supports almost all of them).
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Banana Pi series is a well known series of single board computers.
The manufacturer, Sinovoip, is less well known. Moreover, the board
markings do not mention Sinovoip, but only the Banana Pi logo, and
the BPI-M* model name.
Rename the dts file to use the more well known name. Also fix up
some of the model names and labels to match other Banana Pi boards.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
- Lubomir updates all BCM2835 (Raspberry Pi family) Device Tree source files with
their proper information about the on-board USB Ethernet adapter so there is
appropriate binding between this USB device and a device_node (useful for MAC
address fetching and stuff)
- Raveendra adds the ADC controller Device Tree nodes to the Cygnus SoC device
tree include files
- Rafal updates the BCM5301x Device Tree by separating how we specify the NAND
chip-select information in a first change and then fixes the NAND controller
ECC configuration for the D-Link DIR-885L
- Florian adds support for the BCM953012ER reference board, adds the HW random
number generator DT node and adds proper memory node information to the
BCM958625HR reference board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Ie0I
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.8/devicetree-part2' of http://github.com/Broadcom/stblinux into next/dt
Merge "additional Broadcom ARM-based SoC Device Tree changes" from Florian Fainelli:
- Lubomir updates all BCM2835 (Raspberry Pi family) Device Tree source files with
their proper information about the on-board USB Ethernet adapter so there is
appropriate binding between this USB device and a device_node (useful for MAC
address fetching and stuff)
- Raveendra adds the ADC controller Device Tree nodes to the Cygnus SoC device
tree include files
- Rafal updates the BCM5301x Device Tree by separating how we specify the NAND
chip-select information in a first change and then fixes the NAND controller
ECC configuration for the D-Link DIR-885L
- Florian adds support for the BCM953012ER reference board, adds the HW random
number generator DT node and adds proper memory node information to the
BCM958625HR reference board
* tag 'arm-soc/for-4.8/devicetree-part2' of http://github.com/Broadcom/stblinux:
ARM: dts: NSP: Specify RAM amount for BCM958625HR board
ARM: BCM5301X: Fix NAND ECC parameters for D-Link DIR-885L
ARM: BCM5301X: Specify NAND chip select and ECC in separated files
ARM: dts: Cygnus: Add Broadcom iproc-static-adc DT node
ARM: dts: BCM5301x: Add BCM953012ER board
ARM: dts: BCM5301x: Add RNG Device Tree node
ARM: bcm2835: dt: Add the ethernet to the device trees
- Add device tree bindings for hi3519 sysctrl
- Add dts files for hi3519
- Tidy up DTB makefile entries to keep the list sorted
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=7zT7
-----END PGP SIGNATURE-----
Merge tag 'hisi-armv7-soc-dt-for-4.8-v2' of git://github.com/hisilicon/linux-hisi into next/dt
Merge "ARM: DT: Hisilicon ARMv7 SoC Hi3519 DT updates for 4.8" from Wei Xu:
- Add device tree bindings for hi3519 sysctrl
- Add dts files for hi3519
- Tidy up DTB makefile entries to keep the list sorted
* tag 'hisi-armv7-soc-dt-for-4.8-v2' of git://github.com/hisilicon/linux-hisi:
ARM: dts: add dts files for Hi3519 and tidy up the makefile entries
ARM: dt-bindings: add device tree bindings for Hi3519 sysctrl
The usual amount of DT patches, among which:
- I2S support
- Support for the AXP809 in the relevant boards (A80 based)
- New boards: Banapi M1+, Banapi M2+, Allwinner Parrot (R16 EVB),
- The other patches to enable various controllers on our boards, most
notably USB OTG
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=XPdf
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-4.8' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/dt
Merge "Allwinner DT changes for 4.8" from Maxime Ripard:
The usual amount of DT patches, among which:
- I2S support
- Support for the AXP809 in the relevant boards (A80 based)
- New boards: Banapi M1+, Banapi M2+, Allwinner Parrot (R16 EVB),
- The other patches to enable various controllers on our boards, most
notably USB OTG
* tag 'sunxi-dt-for-4.8' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux: (54 commits)
ARM: dts: sun5i: Enable otg on the auxtex t004
ARM: sun5i: Allow PLL3 2x fixed factor clock to change PLL3 rate
ARM: sun7i: Add DAI nodes
ARM: sun7i: Add mod1 clock nodes
ARM: dts: sun5i: Add mmc1 / sdio-wifi node to mk802
ARM: dts: sun5i: Add axp152 pmic node to mk802
ARM: dts: sun5i: Enable otg on the mk802
ARM: dts: sun7i: Add BCM53125 switch nodes to the lamobo-r1 board
ARM: sun8i: Add Parrot Board DTS
ARM: dts: sun5i: q8-common: Enable USB-based WiFi
ARM: dts: sun7i: Add dts file for Bananapi M1 Plus board
ARM: dts: sun8i-q8-common: Add support for USB wifi controllers
ARM: dts: sun9i: a80-optimus: Order nodes by alphabetical order
ARM: dts: sun9i: cubieboard4: Order nodes by alphabetical order
ARM: dts: sun7i: Add NFC node to Allwinner A20 SoC
ARM: dts: sun4i: Add NFC node to Allwinner A10 SoC
ARM: dts: sun6i: Add pmic / regulator nodes to Mele M9 dts
ARM: dts: sun6i: Add pmic / regulator nodes to Mele A1000G quad dts
ARM: dts: sun6i: The blue led on the Mele M9 is a power led
ARM: dts: sun6i: The blue led on the Mele A1000G quad is a power led
...
as well as i2s and ethernet support on rk3228/rk3229 devices
and a dts file for the rk3229 eval board.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCAAGBQJXdbKVAAoJEPOmecmc0R2B4t8H/3J/l3fXyAskseN12883GkgO
WxEaCe4LeLbxp9Lcd3jmhXM4WZKPbfngYdLvL6kNh/LZeZT3naa2B55ot0FiIOHQ
PVvAC9ce7T0wTeK/aC2iFU6two6ZMbk8jSRfpfpijHIwK9U1NQcXTssuzvHR+S/L
+QP29M2TP3Y9UrPydx8kpCeH0kav2WmdqNmRdpQ9hokCqAiR2jbXi2N4PNtVl9v9
Vy/s+kFa8RSLzWTUICalwrMzS7j/VyeFKq61NPPjVdfS0Q+poCcdaDw5ZPEtZYBu
eerD1hTou+z7MPz6F5SM3J5U9G8NEp0NO4b3C0eWvAuA9cMv0smJFfqVD4erp40=
=wEmr
-----END PGP SIGNATURE-----
Merge tag 'v4.8-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Audio support and spi-flash on rk3288-veyron Chromedevices
as well as i2s and ethernet support on rk3228/rk3229 devices
and a dts file for the rk3229 eval board.
* tag 'v4.8-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: add support rk3229 evb board
ARM: dts: rockchip: add GMAC nodes for RK322x SoCs
ARM: dts: rockchip: add i2s nodes for RK322x SoCs
ARM: dts: rockchip: rename rk3228.dtsi to rk322x.dtsi
clk: rockchip: add clock-ids for rk3228 MAC clocks
clk: rockchip: add clock-ids for rk3228 audio clocks
ARM: dts: rockchip: rename i2s model for Veyron devices
ARM: dts: rockchip: move rk3288 io-domain nodes to the grf
ARM: dts: rockchip: Enable analog audio on rk3288-veyron chromebooks
ARM: dts: rockchip: Add shared file for audio on rk3288-veyron boards
ARM: dts: rockchip: add SPI flash node for rk3288-veyron
Signed-off-by: Olof Johansson <olof@lixom.net>
* Use APMU on R-Car Gen2 and provide SMP for r8a7793 SoC
* Update console parameters to uniformly use chosen/stdout-path,
serial0, not provide kernel unnecessary command line parameters
* Add DU pins to silk board
* Add support for blanche/r8a7792
* Name pfc subnodes after device name
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=gmxg
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt2-for-v4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Second Round of Renesas ARM Based SoC DT Updates for v4.8
* Use APMU on R-Car Gen2 and provide SMP for r8a7793 SoC
* Update console parameters to uniformly use chosen/stdout-path,
serial0, not provide kernel unnecessary command line parameters
* Add DU pins to silk board
* Add support for blanche/r8a7792
* Name pfc subnodes after device name
* tag 'renesas-dt2-for-v4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (41 commits)
ARM: dts: r8a7792: add SMP support
ARM: dts: r8a7793: Add APMU node and second CPU core
ARM: dts: r8a7791: Add APMU node
ARM: dts: r8a7790: Add APMU nodes
devicetree: bindings: Renesas APMU and SMP Enable method
ARM: dts: kzm9g: Update console parameters
ARM: dts: kzm9d: Update console parameters
ARM: dts: marzen: Add serial port config to chosen/stdout-path
ARM: dts: genmai: Update console parameters
ARM: dts: armadillo800eva: Update console parameters
ARM: dts: r8a7792: add JPU support
ARM: dts: r8a7792: add JPU clocks
ARM: dts: silk: add DU pins
ARM: dts: blanche: add Ethernet support
ARM: dts: blanche: initial device tree
ARM: dts: blanche: document Blanche board
ARM: dts: r8a7792: add IRQC support
ARM: dts: r8a7792: add [H]SCIF support
ARM: dts: r8a7792: add SYS-DMAC support
ARM: dts: r8a7792: initial SoC device tree
...
Signed-off-by: Olof Johansson <olof@lixom.net>
This adds the Cirrus Logic EP7209,EP7211 DT templates and support for
EDB7211 Development board.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- add dts files for Hi3519
- shuffle ARCH_HIGHBANK, ARCH_HISI, ARCH_HIX5HD2 and ARCH_HIP0X
around to keep the list sorted
Signed-off-by: Jiancheng Xue <xuejiancheng@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
- Add two i.MX23/STMP3780 based MP3 player device support, Creative
X-Fi3 and SanDisk Sansa Fuze+
- Add the support of Auvidea H100 device which is a SolidRun MicroSOM
baseboard
- Restructure i.MX7Dual DTS files to support i.MX7Solo and add Toradex
Colibri iMX7S/iMX7D boards
- Device additions and enabling for various boards: mmc device for
utilite-pro, IRQ controller and CAN support for TS-4800, display and
touchscreen support for imx7d-sdb, SAI audio and LCD support for
imx6ul-14x14-evk, gpio power off support for imx6q-bx50v3, etc.
- Update the boards from Freescale/NXP to use WDOG_B pin for reset
- PCI reset polarity correction for imx6qdl-sabresd and imx6q-tbs2910
- Update i.MX board dts files to use generic uart-has-rtscts DT
property instead of vendor specific one
- DTC warning fixing for a few boards which are mostly mismatch between
unit-address and reg property
- Remove SION setting from all mux modes on i.MX25
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXcmoVAAoJEFBXWFqHsHzOQfEH/1z78cIe4bBd61boOge5VGUc
BdVGC4U6vcB1cRxceA8sh6U8QVyDtnojB1r5C3W+Zad4VMIdptGwbxAJne268WTt
iSRY8+Mu81KgrvkQ4flosTp7w8J4DfzithMGzDnhq3vTFblaaAT63u9AcDlcSGCq
1p/wPpqUb7COEBYOAxcOfypIPkZXrcvTfHHm3KOAV+cvNEQHZ0n4kLDWfjFxiUgo
oE+RDTku2q7mfXs22QXCUyTLNlwzuczsQ35sPM4JbIc6JBVYyyF/tHQFB162MB7u
ELK79F4LKip4wUS8b52M3xEQWiB0Cb1jtymomHLdGzguk7FtaV18vSUvA918GB8=
=2NUH
-----END PGP SIGNATURE-----
Merge tag 'imx-dt-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
The i.MX device tree update for 4.8:
- Add two i.MX23/STMP3780 based MP3 player device support, Creative
X-Fi3 and SanDisk Sansa Fuze+
- Add the support of Auvidea H100 device which is a SolidRun MicroSOM
baseboard
- Restructure i.MX7Dual DTS files to support i.MX7Solo and add Toradex
Colibri iMX7S/iMX7D boards
- Device additions and enabling for various boards: mmc device for
utilite-pro, IRQ controller and CAN support for TS-4800, display and
touchscreen support for imx7d-sdb, SAI audio and LCD support for
imx6ul-14x14-evk, gpio power off support for imx6q-bx50v3, etc.
- Update the boards from Freescale/NXP to use WDOG_B pin for reset
- PCI reset polarity correction for imx6qdl-sabresd and imx6q-tbs2910
- Update i.MX board dts files to use generic uart-has-rtscts DT
property instead of vendor specific one
- DTC warning fixing for a few boards which are mostly mismatch between
unit-address and reg property
- Remove SION setting from all mux modes on i.MX25
* tag 'imx-dt-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (47 commits)
ARM: dts: imx7: add Toradex Colibri iMX7S/iMX7D support
ARM: dts: imx7d: move input header into base device tree
ARM: dts: imx7d: recreate imx7d.dtsi with i.MX 7Dual specifics
ARM: dts: imx7d: use imx7s.dtsi as base device tree
ARM: dts: imx7d-sdb: Add support for touchscreen
ARM: dts: imx7d-sdb: Add display support
ARM: dts: imx7d: Add SPI support
ARM: dts: imx6q-bx50v3: Add gpio power off support
ARM: dts: imx6ul-pico-hobbit: Fix Ethernet PHY reset GPIO
ARM: dts: imx6q-tbs2910: fix pcie reset polarity
ARM: dts: imx6sx-sdb: Use WDOG_B pin reset
ARM: dts: imx6ul-evk: Use WDOG_B pin reset
ARM: dts: imx7d-sdb: Use WDOG_B pin reset
ARM: dts: imx6qdl-sabresd: Use WDOG_B pin reset
ARM: dts: utilite-pro: add mmc card slot support
ARM: dts: imx6q-cm-fx6: fix the operation points
ARM: dts: imx6qdl.dtsi: add "arm,shared-override" for pl310
ARM: imx25-pinfunc: remove SION from all modes
ARM: imx25-pinfunc: document SION being important for MX25_PAD_SD1_CMD__SD1_CMD
ARM: dts: ls1021a: Add dis_rxdet_inp3_quirk property to USB3 node
...
Signed-off-by: Olof Johansson <olof@lixom.net>
- New board: at91sam9260ek
- Fixes for the sam9_l9260
- Sama5d2 Xplained PMIC fix
- Addition of the PMU node for the sama5d2
-----BEGIN PGP SIGNATURE-----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=F38N
-----END PGP SIGNATURE-----
Merge tag 'at91-ab-4.8-dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux into next/dt
DT Changes for 4.8 #2:
- New board: at91sam9260ek
- Fixes for the sam9_l9260
- Sama5d2 Xplained PMIC fix
- Addition of the PMU node for the sama5d2
* tag 'at91-ab-4.8-dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
ARM: dts: at91: sama5d2_xplained: Update the pmic node
ARM: dts: at91: sama5d2: add PMU node
ARM: dts: at91: sam9_l9260: Modify information in LED nodes.
ARM: dts: at91: sam9_l9260: Add pinctrl information to ethernet node.
ARM: dts: at91: add at91sam9260ek board DT
Signed-off-by: Olof Johansson <olof@lixom.net>
The Parrot Board is an evaluation board with an Allwinner R16 (assumed
to be close to an Allwinner A33), 4GB of eMMC, 512MB of RAM, USB host
and OTG, a WiFi/Bluetooth combo chip, a micro SD Card reader, 2
controllable buttons, an LVDS port with separated backlight and
capacitive touch panel ports, an audio/microphone jack, a camera CSI
port, 2 sets of 22 GPIOs and an accelerometer.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add support for the Bananapi M1 Plus A20 development board from
sinovoip.com.cn . This board is nearly a clone of the Lemaker's
Bananapro, but differ with the wlan chipset connection and i2s pinout.
And I also enable the integrated audio codec on default.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The BPI-M2+ is an H3 development board. It is a smaller form factor than
the original BPI-M2, with the new H3 SoC.
It has 1GB DRAM, 8GB eMMC, a micro SD card slot, HDMI output, 2 USB
host connector and 1 USB OTG connector, an IR receiver, WiFi+BT based
on Ampak AP6212.
The board also has a 3 pin header for (debug) UART, a 40 pin GPIO header
based on the Raspberry Pi B+, but the peripheral signals are not the
same, and an FPC connector for connecting BPI's camera.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add Device Tree source file for at91sam9260ek board. This official Atmel
Evaluation Kit is designed around a SoC based on a ARM 926 core the
at91sam9260.
The board is also added to the dts Makefile.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add support for the Broadcom BCM953012 Enterprise Router reference
board, enable the following peripherals:
- UART0 (UART1 is not populated)
- WPS and restart GPIO buttons
- Ethernet switch w/ only two facing ports
- NAND flash
- SPI-NOR flash
Acked-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add support for the Computer on Module Colibri iMX7S/iMX7D along
with the development/evaluation carrier board device trees. Follow
the usual hierarchic include model, maintaining shared configuration
in imx7-colibri.dtsi and imx7-colibri-eval-v3.dtsi respectively.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This is the first Dragonboard based on APQ8060 and PM8058. It
was produced in 2011 in cooperation between Qualcomm and
BSQUARE.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This board has been renamed recently and announced at
https://eragon.einfochips.com/products/sd-600eval.html
So rename this board files so that it reflects actual product in market.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Initial release for rk3229 evb board, and turn the GMAC on.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
- Chris provides documentation and DTS fixes for the bcm11351 CPU enable-method in preparation
for adding support for the BCM23550 SoC and its corresponding documentation, SoC dtsi
and the Sparrow board DTS file
- Jon adds MSI support to the PCI nodes, updates the secondary cores boot address for the B0
production revision of the Northstar Plus SoC, adds a DTS for the BCM958625HR board, another
one for the BCM958525XMC board, and finally adds the PL330 DMA controller to the NSP DTS
- Rafal enables the SPI NOR flash on dual flash systems (NAND + SPI) on the BCM5301x SoCs
and devices
- Florian adds support for the BCM5301x built-in Ethernet switch by adding nodes for the
Gigabit MAC controllers and the Switch Register Access block, and finally updates the
SmartRG SR-400AC board with its switch port layout
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=0GWx
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.8/devicetree' of http://github.com/Broadcom/stblinux into next/dt
This pull request contains Device Tree changes for Broadcom ARM-based SoCs:
- Chris provides documentation and DTS fixes for the bcm11351 CPU enable-method in preparation
for adding support for the BCM23550 SoC and its corresponding documentation, SoC dtsi
and the Sparrow board DTS file
- Jon adds MSI support to the PCI nodes, updates the secondary cores boot address for the B0
production revision of the Northstar Plus SoC, adds a DTS for the BCM958625HR board, another
one for the BCM958525XMC board, and finally adds the PL330 DMA controller to the NSP DTS
- Rafal enables the SPI NOR flash on dual flash systems (NAND + SPI) on the BCM5301x SoCs
and devices
- Florian adds support for the BCM5301x built-in Ethernet switch by adding nodes for the
Gigabit MAC controllers and the Switch Register Access block, and finally updates the
SmartRG SR-400AC board with its switch port layout
* tag 'arm-soc/for-4.8/devicetree' of http://github.com/Broadcom/stblinux:
ARM: dts: BCM5310x: Enable switch ports on SmartRG SR400AC
ARM: dts: BCM5301X: Add SRAB interrupts
ARM: dts: Enable SRAB switch and GMACs on 5301x DTS
ARM: dts: NSP: Add PL330 support
ARM: dts: NSP: Add XMC board support
ARM: dts: bcm23550: Add device tree files
Documentation: devicetree: Document BCM23550 bindings
ARM: BCM5301X: Enable SPI-NOR on dual flash devices
ARM: dts: NSP: Add new DT file for bcm958625hr
ARM: dts: NSP: modify second CPU address
ARM: dts: NSP: Add MSI support on PCI
ARM: BCM: modify Broadcom CPU enable method
ARM: dts: fix use of bcm11351 enable method
Documentation: Binding docs for bcm11351 enable method
Signed-off-by: Olof Johansson <olof@lixom.net>
Add the initial device tree for the R8A7792 SoC based Blanche board.
The board has 2 debug serial ports: SCIF0 and SCIF3; include support for
them, so that the serial console can work.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The CompuLab Utilite Pro is a miniature fanless desktop pc based on
the i.MX6 Quad powered cm-fx6 module. It features two serial ports,
USB OTG, 4x USB, analog audio and S/PDIF, 2x Gb Ethernet, HDMI and
DVI ports, an on-board 32GB SSD, a mmc slot, and on-board wifi/bt.
Add initial support for it including USB, Ethernet (both ports), sata
and HDMI support.
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Auvidea H100 is a baseboard for the SolidRun MicroSOM.
Its primary feature is a Toshiba TC358743 HDMI to CSI decoder,
allowing the board to work as HDMI passthrough and framegrabber.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The BCM958525XMC board is a smaller form factor typically used as
controller boards for switches. This smaller board has less devices
pinned out, so only a few need be populated in the device tree.
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add support for this small MP3 player based on STMP3780 (rev.3).
Currently supported are both external microSD and internal SD-NAND
bridge, PWM and USB gadget.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for this small MP3 player based on STMP3780 (rev.4).
Currently supported is both external microSD and internal SD-NAND
bridge, PWM and USB gadget.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
sam9-l9260 is a low cost board designed by Olimex.
More information is available at:
https://www.olimex.com/Products/ARM/Atmel/SAM9-L9260/
Signed-off-by: Raashid Muhammed <raashidmuhammed@zilogic.com>
Reviewed-by: Vijay Kumar B. <vijaykumar@bravegnu.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add device tree files for the Broadcom BCM23550 SoC and the
Broadcom Sparrow board.
Signed-off-by: Chris Brand <chris.brand@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
commit 27dd9af6bc ("ARM: dts: sunxi: Add a olinuxino-lime2-emmc")
added the new emmc equipped lime2 but forgot its Makefile.
This patch adds an entry to the Makefile.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Create a new device tree file for the Broadcom Northstar Plus HR SVK.
This SVK is a smaller form factor, and thus only has 2 PCI slots and 1
UART. Also, it has the ability to reboot via GPIO (instead of the
processor reset).
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The Hardkernel's Odroid XU board was first design with big.LITTLE SoC
from Samsung: the Exynos5410. Details:
1. Exynos5410 octa-core (A15+A7, however as of now only one cluster is
enabled),
2. 2 GB DDR3 RAM,
3. PowerVR SGX544MP3 GPU (not enabled in DTS),
4. USB 3.0 Host x 1, USB 3.0 OTG x 1, USB 2.0 Host x 4,
5. HDMI 1.4a, MIPI DSI and Display Port (Display Port not on all of
revisions though),
6. eMMC 4.5 and microSD slots.
Comparing this board to Odroid XU3 (more popular), the differences are:
1. Exynos5410 instead of 5422,
2. MIPI DSI LCD connector,
3. Main PMIC: Maxim 77802 instead of S2MPS11,
4. USB3503+LAN9730 instead of integrated LAN9514,
5. eMMC 4.5 instead of eMMC 5.0,
This patch adds initial support for the XU board with working basic
functions, eMMC/SD and USB (including attached ethernet adapter).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Link: http://www.hardkernel.com/main/products/prdt_info.php?g_code=G137510300620
This is a collection of a few late fixes and other misc. stuff that
had dependencies on things being merged from other trees.
The Renesas R-Car power domain handling, and the Nvidia Tegra USB
support both hand notable changes that required changing the DT binding
in a way that only provides compatibility with old DT blobs on new
kernels but not vice versa. As a consequence, the DT changes
are based on top of the driver changes and are now in this branch.
For NXP i.MX and Samsung Exynos, the changes in here depend on
other changes that got merged through the clk maintainer tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=I0Be
-----END PGP SIGNATURE-----
Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late DT updates from Arnd Bergmann:
"This is a collection of a few late fixes and other misc stuff that had
dependencies on things being merged from other trees.
The Renesas R-Car power domain handling, and the Nvidia Tegra USB
support both hand notable changes that required changing the DT
binding in a way that only provides compatibility with old DT blobs on
new kernels but not vice versa. As a consequence, the DT changes are
based on top of the driver changes and are now in this branch.
For NXP i.MX and Samsung Exynos, the changes in here depend on other
changes that got merged through the clk maintainer tree"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (35 commits)
ARM: dts: exynos: Add support of Bus frequency using VDD_INT for exynos5422-odroidxu3
ARM: dts: exynos: Add bus nodes using VDD_INT for Exynos542x SoC
ARM: dts: exynos: Add NoC Probe dt node for Exynos542x SoC
ARM: dts: exynos: Add support of bus frequency for exynos4412-trats/odroidu3
ARM: dts: exynos: Expand the voltage range of buck1/3 regulator for exynos4412-odroidu3
ARM: dts: exynos: Add support of bus frequency using VDD_INT for exynos3250-rinato
ARM: dts: exynos: Add exynos4412-ppmu-common dtsi to delete duplicate PPMU nodes
ARM: dts: exynos: Add bus nodes using VDD_MIF for Exynos4210
ARM: dts: exynos: Add bus nodes using VDD_INT for Exynos4x12
ARM: dts: exynos: Add bus nodes using VDD_MIF for Exynos4x12
ARM: dts: exynos: Add bus nodes using VDD_INT for Exynos3250
ARM: dts: exynos: Add DMC bus frequency for exynos3250-rinato/monk
ARM: dts: exynos: Add DMC bus node for Exynos3250
ARM: tegra: Enable XUSB on Nyan
ARM: tegra: Enable XUSB on Jetson TK1
ARM: tegra: Enable XUSB on Venice2
ARM: tegra: Add Tegra124 XUSB controller
ARM: tegra: Move Tegra124 to the new XUSB pad controller binding
ARM: dts: r8a7794: Use SYSC "always-on" PM Domain
ARM: dts: r8a7793: Use SYSC "always-on" PM Domain
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ED1J
-----END PGP SIGNATURE-----
Merge tag 'aspeed-for-4.7-dts' of https://github.com/shenki/linux into next/dt
Merge "aspeed devicetree for 4.7" from Joel Stanley:
This device trees for a pair of Aspeed BMC SoCs and the boards that
they sit in.
* tag 'aspeed-for-4.7-dts' of https://github.com/shenki/linux:
arm/dst: Add Aspeed ast2500 device tree
arm/dts: Add Aspeed ast2400 device tree
doc/devicetree: Add Aspeed and Tyan to vendor-prefixes
- Update display clock configuration for imx6q-b850v3 board
- Use watchdog external reset for imx6q-ba16 board
- Update operating points settings for i.MX6UL/SX/DL
- New board support: imx6ul-pico-hobbit and imx6q-marsboard
- Add SAI audio support for imx6ul-14x14-evk board
- Enable USB OTG support for M53EVK board
- A couple of fixes on DTC warnings
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXKMJoAAoJEFBXWFqHsHzOcpsH/0bFP/P36+1O8HstQ9+a/BGk
r3BMzTeC9glqVO2XXl5VDRp0v/kRHfNETZy7ML7Ghd0oE0VTBfw3j+b/0aQQUxbY
GdyGSWjrKFlzuFmBjHP/ZJg4iZfZREUAXAql6iYrXapvx8XM+Si0Ear/urK5yX9l
laVu4tszpc0ip5YwzSVOYulwt2lNhialCN/AavQ57bvb1t3pGyv5qtIQ9NNbrxJt
0ZEj/dq5P4GKwHweKUo9jIPPkgygILLq5N9nNnyCkmVbcK5jLFa/Gr42h/hGNyCX
gjOeo9jNX5zdcUie38NJbRfcEmqUFTUXXIJKjYPCi/mkpj4xUMEnrWlzcOqY46I=
=q9tG
-----END PGP SIGNATURE-----
Merge tag 'imx-dt-4.7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
Merge "i.MX device tree updates for 4.7, take 2: from Shawn Guo:
The i.MX device tree updates for 4.7, take 2:
- Update display clock configuration for imx6q-b850v3 board
- Use watchdog external reset for imx6q-ba16 board
- Update operating points settings for i.MX6UL/SX/DL
- New board support: imx6ul-pico-hobbit and imx6q-marsboard
- Add SAI audio support for imx6ul-14x14-evk board
- Enable USB OTG support for M53EVK board
- A couple of fixes on DTC warnings
* tag 'imx-dt-4.7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: mx5: dts: Enable USB OTG on M53EVK
ARM: dts: imx6ul-14x14-evk: Add audio support
ARM: dts: imx6qdl: Remove unneeded unit-addresses
ARM: dts: imx6: apalis: parallel lcd display support on ixora
ARM: dts: imx6sx-sdb: Add 198MHz operational point
ARM: dts: imx28-m28: Remove unneeded partition nodes
ARM: dts: imx6ul-pico-hobbit: Add initial support
ARM: dts: imx6: Do not hardcode the CLKO clock
ARM: dts: imx6: Add dts for Embest MarS Board
ARM: dts: imx6: fix dtc warnings for ipu endpoints
ARM: dts: imx6dl: Fix the VDD_ARM_CAP voltage for 396MHz operation
ARM: dts: imx6sx: Add 198MHz operating point
ARM: dts: imx6ul: Fix operating points
ARM: dts: imx6q-ba16: use wdog external reset
ARM: dts: imx: b450/b650v3: Move ldb_di clk assignment
ARM: dts: imx6q-b850v3: Update display clock source
ARM: dts: imx6q-b850v3: Remove ldb panel
The usual bunch of changes, mostly:
* Addition of the SPDIF support
* Addition of the pre-requisites for the display support
* New boards: Difrence DIT4350, colorfly e708 q1, Dserve DSRV9703C,
Polaroid MID2809PXE4, Orange Pi PC, Orange Pi 2
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tEwH
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-4.7' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/dt
Merge "Allwinner DT additions for 4.7" from Maxime Ripard:
The usual bunch of changes, mostly:
* Addition of the SPDIF support
* Addition of the pre-requisites for the display support
* New boards: Difrence DIT4350, colorfly e708 q1, Dserve DSRV9703C,
Polaroid MID2809PXE4, Orange Pi PC, Orange Pi 2
* tag 'sunxi-dt-for-4.7' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux: (38 commits)
ARM: dts: sun7i: Enable S/PDIF on the Cubietruck
ARM: sun5i: Add DRAM gates
ARM: sun5i: Add TV encoder gate to the DTSI
ARM: sun5i: dt: Add pll3 and pll7 clocks
ARM: dts: sun8i: Add dts file for the Orange Pi One SBC
ARM: sun7i: dt: Enable dram gate 5 (tve0 clock) for simplefb TV output
ARM: sun4i: dt: Enable dram gate 5 (tve0 clock) for simplefb TV output
ARM: dts: sun5i-a13-olinuxino-micro: enable USB DRC
ARM: dts: sun8i: Base Orange Pi Plus dts on the Orange Pi 2 dts
ARM: dts: sun8i: Orangepi plus gpio keys fixes and improvements
ARM: dts: sun8i: Add dts for Orange Pi 2 SBC
ARM: dts: sun8i: Add Orange Pi PC support
ARM: dts: sun8i: Fix pio nodes Orangepi Plus dts
ARM: dts: sun7i: Add SPDIF to the Itead Ibox
ARM: dts: sun4i: Add SPDIF to the Mele A1000
ARM: dts: sun7i: Add the SPDIF block to the A20
ARM: dts: sun4i: Add the SPDIF block to the A10
ARM: dts: sun7i: Add the SPDIF clk to the A20
ARM: dts: sun4i: Add the SPDIF clk to the A10
ARM: dts: sun7i: Add SPDIF TX pin to the A20
...
to the binding-change that made it into 4.6, adds rk3288 i2c controller
nodes and moves the rk3288 thermal data into the soc dtsi, as there
really is no need to have that separate file.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCAAGBQJXIoqfAAoJEPOmecmc0R2BBX0H/iBNCd50u66X9sAgpoi9HgPs
QghFjG9wxXUAtSGfMWirgmjMVNwCfNBTPUMHgZpIn61Yxgm5vh1dNTiBIGYoNVwv
XLLgSRmc4tHKdRQmdw2bik9Do4AKR0NfWN4UG1YtaJnPWVGiBPnlvGqr8sdJHZkS
VEPeh5sUgLi8nI5fR2UQxTlv5Epptal72k5kWrPWtLuFN3diPOPZ5tblSESt5OIE
EfNARkNVLMRtt+nEZyWF8hFtdIF+gJ+9CKwIt83w9c2Mudbrcpha+HYzOWVMUIY/
g0itfsoW48PyI81UpoBaNmKQXj5S0k8HuDrZ65HMgYWm9pJ5dNsJdlcyQolRmKM=
=rD4T
-----END PGP SIGNATURE-----
Merge tag 'v4.7-rockchip-dts32-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Merge "Rockchip dts32 updates for v4.7 - part2" from Heiko Stübner:
This adds the rk3288-miqi as new board, adapts the edp-phy settings
to the binding-change that made it into 4.6, adds rk3288 i2c controller
nodes and moves the rk3288 thermal data into the soc dtsi, as there
really is no need to have that separate file.
* tag 'v4.7-rockchip-dts32-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: move the rk3288 thermal data into rk3288.dtsi
ARM: dts: rockchip: add MiQi board from mqmaker
dt-bindings: add vendor-prefix for mqmaker
ARM: dts: rockchip: move rk3288 edp phy under the GRF
ARM: dts: rockchip: make rk3288-grf a simple-mfd
ARM: dts: rockchip: add i2c nodes for RK3228 SoCs
This adds a common device tree for all fifth generation Aspeed systems,
and a board specific device tree for the ast2500 evaluation board.
Signed-off-by: Joel Stanley <joel@jms.id.au>
A common device tree for all forth gen/ast2400 systems and a board
specific dts for the Palmetto OpenPower developemnt machine which was
used for testing.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add initial support for imx6ul pico hobbit board.
For information about this board, please visit:
http://www.wandboard.org/images/hobbit/hobbitboard-imx6ul-reva1.pdf
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
