We need to disable clock gating in this unit to work around
hardware issue causing possible corruption/hang.
v2: name the bit (Ville)
v3: leave the fix enabled for 2227050 and set correct bit (Matthew)
v4: Split out the skl part in separate commit for easier backport
References: HSD#2227156, HSD#2227050
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465309159-30531-20-git-send-email-mika.kuoppala@intel.com
According to bspec this workaround helps to reduce lag and improve
performance on edp.
Documentation suggests this for bdw and all gen9. However evidence
shows that this register is missing on gen9 and causing unclaimed mmio
access if we access it. So apply to bdw only where the reg
exists and can hold its value.
v2: drop skl
References: HSD#2134579
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465309159-30531-11-git-send-email-mika.kuoppala@intel.com
We need this crucial workaround from skl also to all kbl revisions.
Lack of it was causing system hangs on skl enabling so this is
a must have.
v2: Don't add revid checks to gen9 init workarounds (Arun)
References: HSD#2126660
Cc: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465309159-30531-8-git-send-email-mika.kuoppala@intel.com
Past evidence with system hangs and hsds tie
WaForceEnableNonCoherent and WaDisableHDCInvalidation to
WaForceContextSaveRestoreNonCoherent. Documentation
states that WaForceContextSaveRestoreNonCoherent would
not be needed on skl past E0 but evidence proved otherwise. See
commit <510650e8b2ab> ("drm/i915/skl: Fix spurious gpu hang with gt3/gt4
revs"). In this scope consider kbl to be skl with a bigger revision than
E0 so play it safe and bind these two workarounds to the
WaForceContextSaveRestoreNonCoherent, and apply to all gen9.
v2: fix comment (Matthew)
References: HSD#2134449, HSD#2131413
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465309159-30531-7-git-send-email-mika.kuoppala@intel.com
We need to disable clock gating in this unit to work around
hardware issue causing possible corruption/hang.
v2: name the bit (Ville)
v3: leave the fix enabled for 2227050 and set correct bit (Matthew)
References: HSD#2227156, HSD#2227050
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465309159-30531-2-git-send-email-mika.kuoppala@intel.com
The atomic version of intel_pre_plane_update did not check
for HAS_GMCH_DISPLAY before calling intel_set_memory_cxsr().
While this doesn't cause any issues on its own (it will
return without doing anything if the hardware doesn't
have the required feature), the drm_wait_one_vblank() that
is needed if memory self-refresh is disabled introduces
an unnecessary delay in the suspend path.
In cases where i915 is on the critical path it means that
we slow down suspend by 16.8ms on platforms that don't
need to disable memory self-refresh.
Signed-off-by: David Weinehall <david.weinehall@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463662236-18192-1-git-send-email-david.weinehall@linux.intel.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Apparently some CHV boards failed to hook up the port presence straps
for HDMI ports as well (earlier we assumed this problem only affected
eDP ports). So let's check the VBT in addition to the strap, and if
either one claims that the port is present go ahead and register the
relevant connector.
While at it, change port D to register DP before HDMI as we do for ports
B and C since
commit 457c52d87e ("drm/i915: Only ignore eDP ports that are connected")
Also print a debug message when we register a HDMI connector to aid
in diagnosing missing/incorrect ports. We already had such a print for
DP/eDP.
v2: Improve the comment in the code a bit, note the port D change in
the commit message
Cc: Radoslav Duda <radosd@radosd.com>
Tested-by: Radoslav Duda <radosd@radosd.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=96321
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464945463-14364-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Add drm_crtc_enable_color_mgmt(), remove drm_helper_crtc_enable_color_mgmt()
and update drm/i915-driver (the only user of the old function).
The new function is more flexible. It allows driver to enable only the
features it has without forcing to enable all three color management
properties: degamma lut, csc matrix (ctm), and gamma lut.
Suggested-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The recent patch
. fce91f2 drm/i915/guc: add enable_guc_loading parameter
enabled GuC loading and submission by default, but as issues
were found with warnings being issued during suspend-resume
cycles, GuC loading was disabled by default, by patch
. 2335986 drm/i915/guc: Disable automatic GuC firmware loading
Those warnings have been resolved, so this patch re-enables GuC
loading and submission by default.
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465287291-2187-1-git-send-email-david.s.gordon@intel.com
When resetting and reloading the GuC, the GuC submission management code
also needs to destroy and recreate the GuC client(s). Currently this is
done by a separate call from the GuC loader, but really, it's just an
internal detail of the submission code. So here we remove the call from
the loader (which is too late, really, because the GuC has already been
reloaded at this point) and put it into guc_submission_init() instead.
This means that any preexisting client is destroyed *before* the GuC
(re)load and then recreated after, iff the firmware was successfully
loaded. If the GuC reload fails, we don't recreate the client, so
fallback to execlists mode (if active) won't leak the client object
(previously, the now-unusable client would have been left allocated,
and leaked if the driver were unloaded).
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
The last stage of the GuC loader also sanitises the GuC submission
settings, so should be called unconditionally (even on platforms
without a GuC) to ensure consistent settings; in particular, this
prevents any attempt to use GuC submission on GuCless platforms!
Also fix error path handling and clarify DRM_INFO fallback message.
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Fix the failure mode where the display appears split, or shifted about
2/3 of the screen, and the color components are cycled. Turns out we
were missing the crucial BXT_DEFEATURE_DPI_FIFO_CTR bit in the
EOT_DISABLE register.
Per bspec, with the bit set, the "mipi_dpf_vblank_start" signal is
asserted only when the complete frame is transferred in the DPHY line
and also the DPI FIFO is flushed out at the end of each frame.
The problem was mitigated by keeping the panel fitter enabled, but that
only limited the issue to a shift of about 0..10 pixels. With the fix
here, the panel fitter workaround does not seem to be needed at all.
While at it, set BXT_DPHY_DEFEATURE_EN in EOT_DISABLE register which is
also needed per the BXT DSI mode set sequence.
Issue: VIZ-7610
Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ramalingam C <ramalingam.c@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464965825-31035-1-git-send-email-jani.nikula@intel.com
Just fallout from switching from asciidoc to sphinx/rst.
v2: Found more. Also s/\//#/ in the vgpu ascii-art - sphinx treats
those as comments and switch to variable-width, which wreaks the
layout.
v3: Undo some of the hacks, rebasing onto latest version of Jani's
series fixed it.
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
It's kinda pointless to have 2 separate mallocs for these. And when we
add more per-plane state in the future it's even more pointless.
Right now there's no such thing planned, but both Gustavo's per-crtc
fence patches, and some nonblocking commit helpers I'm playing around
with will add more per-crtc stuff. It makes sense to also consolidate
planes, just for consistency.
In the future we can use this to store a pointer to the preceeding
state, making an atomic update entirely free-standing. This will be
needed to be able to queue them up with a depth > 1.
Cc: Gustavo Padovan <gustavo@padovan.org>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464818821-5736-11-git-send-email-daniel.vetter@ffwll.ch
Mostly this is unexpected indents. But really it's just a
demonstration for my patch, all these issues have been found&fixed
using the correct source file and line number support I just added.
All line numbers have been perfectly accurate.
One issue looked a bit fishy in intel_lrc.c, where I don't quite grok
what sphinx is unhappy about. But since that file looks like it has
never seen a proper kernel-doc parser I figured better to fix in a
separate path.
v2: Use fancy new &drm_device->struct_mutex linking (Jani).
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: linux-doc@vger.kernel.org
Cc: Jonathan Corbet <corbet@lwn.net>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
The VBT has these mysterious H/V image sizes as part of the display
timings. Looking at some dumps those appear to be the physical
dimensions in mm. Which makes sense since the timing descriptor matches
the format used by EDID detailed timing descriptor, which defines these
as "H/V Addressable Video Image Size in mm".
So let's use that information from the panel fixed mode to get the
physical dimensions for LVDS/eDP/DSI displays. And with that we can
fill out the display_info so that userspace can get at it via
GetConnector.
v2: Use (hi<<8)|lo instead of broken (hi<<4)+lo
Handle LVDS and eDP too
Cc: Stephen Just <stephenjust@gmail.com>
Tested-by: Stephen Just <stephenjust@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=96255
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464685714-30507-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
My old 845g complains that the child_device_size inside its VBT,
version 110, is incorrect. Let's fiddle with the version matching such
that it works with this VBT (i.e. treat BIOS v110 as having the same size
as v108).
Fixes [drm:intel_bios_init] *ERROR* Unexpected child device config
size 27 (expected 33 for VBT version 110)
Whether this is correct, no one knows - but it works for this particular
machine.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464800923-6054-1-git-send-email-chris@chris-wilson.co.uk
Git got absolutely destroyed with all our cherry-picking from
drm-intel-next-queued to various branches. It ended up inserting
intel_crtc_page_flip 2x even in intel_display.c.
Backmerge to get back to sanity.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
drm-intel-next-2016-05-22:
- cmd-parser support for direct reg->reg loads (Ken Graunke)
- better handle DP++ smart dongles (Ville)
- bxt guc fw loading support (Nick Hoathe)
- remove a bunch of struct typedefs from dpll code (Ander)
- tons of small work all over to avoid casting between drm_device and the i915
dev struct (Tvrtko&Chris)
- untangle request retiring from other operations, also fixes reset stat corner
cases (Chris)
- skl atomic watermark support from Matt Roper, yay!
- various wm handling bugfixes from Ville
- big pile of cdclck rework for bxt/skl (Ville)
- CABC (Content Adaptive Brigthness Control) for dsi panels (Jani&Deepak M)
- nonblocking atomic commits for plane-only updates (Maarten Lankhorst)
- bunch of PSR fixes&improvements
- untangle our map/pin/sg_iter code a bit (Dave Gordon)
drm-intel-next-2016-05-08:
- refactor stolen quirks to share code between early quirks and i915 (Joonas)
- refactor gem BO/vma funcstion (Tvrtko&Dave)
- backlight over DPCD support (Yetunde Abedisi)
- more dsi panel sequence support (Jani)
- lots of refactoring around handling iomaps, vma, ring access and related
topics culmulating in removing the duplicated request tracking in the execlist
code (Chris & Tvrtko) includes a small patch for core iomapping code
- hw state readout for bxt dsi (Ramalingam C)
- cdclk cleanups (Ville)
- dedupe chv pll code a bit (Ander)
- enable semaphores on gen8+ for legacy submission, to be able to have a direct
comparison against execlist on the same platform (Chris) Not meant to be used
for anything else but performance tuning
- lvds border bit hw state checker fix (Jani)
- rpm vs. shrinker/oom-notifier fixes (Praveen Paneri)
- l3 tuning (Imre)
- revert mst dp audio, it's totally non-functional and crash-y (Lyude)
- first official dmc for kbl (Rodrigo)
- and tons of small things all over as usual
* 'drm-intel-next' of git://anongit.freedesktop.org/drm-intel: (194 commits)
drm/i915: Revert async unpin and nonblocking atomic commit
drm/i915: Update DRIVER_DATE to 20160522
drm/i915: Inline sg_next() for the optimised SGL iterator
drm/i915: Introduce & use new lightweight SGL iterators
drm/i915: optimise i915_gem_object_map() for small objects
drm/i915: refactor i915_gem_object_pin_map()
drm/i915/psr: Implement PSR2 w/a for gen9
drm/i915/psr: Use ->get_aux_send_ctl functions
drm/i915/psr: Order DP aux transactions correctly
drm/i915/psr: Make idle_frames sensible again
drm/i915/psr: Try to program link training times correctly
drm/i915/userptr: Convert to drm_i915_private
drm/i915: Allow nonblocking update of pageflips.
drm/i915: Check for unpin correctness.
Reapply "drm/i915: Avoid stalling on pending flips for legacy cursor updates"
drm/i915: Make unpin async.
drm/i915: Prepare connectors for nonblocking checks.
drm/i915: Pass atomic states to fbc update functions.
drm/i915: Remove reset_counter from intel_crtc.
drm/i915: Remove queue_flip pointer.
...
Frist -misc pull for 4.8, with pretty much just random all over plus a few
more lockless gem BO patches acked/reviewed by driver maintainers.
I'm starting a bit earlier this time around because there's a few invasive
patch series to land (nonblocking atomic prep work, fence prep work,
rst/sphinx kerneldoc finally happening) and I need a baseline with all the
branches merged.
* tag 'topic/drm-misc-2016-06-01' of git://anongit.freedesktop.org/drm-intel: (21 commits)
drm/vc4: Use lockless gem BO free callback
drm/vc4: Use drm_gem_object_unreference_unlocked
drm: Initialize a linear gamma table by default
drm/vgem: Use lockless gem BO free callback
drm/qxl: Don't set a gamma table size
drm/msm: Nuke dummy gamma_set/get functions
drm/cirrus: Drop redundnant gamma size check
drm/fb-helper: Remove dead code in setcolreg
drm/mediatek: Use lockless gem BO free callback
drm/hisilicon: Use lockless gem BO free callback
drm/hlcd: Use lockless gem BO free callback
vga_switcheroo: Support deferred probing of audio clients
vga_switcheroo: Add helper for deferred probing
virtio-gpu: fix output lookup
drm/doc: Unify KMS Locking docs
drm/atomic-helper: Do not call ->mode_fixup for CRTC which will be disabled
Fix annoyingly awkward typo in drm_edid_load.c
drm/doc: Drop vblank_disable_allow wording
drm: use seqlock for vblank time/count
drm/mm: avoid possible null pointer dereference
...
if downscaling is enabled plane data rate increases according to scaling
amount. take scaling amount under consideration while calculating plane
data rate
v2: Address Matt's comments, where data rate was overridden because of
missing else.
v3 (by Matt):
- Add braces to 'else' branch to match kernel coding style
- Adjust final calculation now that skl_plane_downscale_amount()
returns 16.16 fixed point value instead of a decimal fixed point
v4 (by Matt):
- Avoid integer overflow by making sure final multiplication is
treated as 64-bit.
Cc: matthew.d.roper@intel.com
Signed-off-by: Kumar, Mahesh <mahesh1.kumar@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Kumar Mahesh <mahesh1.kumar@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463695381-21368-1-git-send-email-matthew.d.roper@intel.com
Don't use pipe pixel rate for plane pixel rate. Calculate plane pixel according
to formula
adjusted plane_pixel_rate = adjusted pipe_pixel_rate * downscale ammount
downscale amount = max[1, src_h/dst_h] * max[1, src_w/dst_w]
if 90/270 rotation use rotated width & height
v2: use intel_plane_state->visible instead of (fb == NULL) as per Matt's
comment.
v3 (by Matt):
- Keep downscale amount in 16.16 fixed point rather than converting to
decimal fixed point.
- Store adjusted plane pixel rate in plane state instead of the plane
parameters structure that we no longer use.
v4 (by Matt):
- Significant rebasing onto latest atomic watermark work
- Don't bother storing plane pixel rate in state; just calculate it
right before the calls that make use of it.
- Fix downscale calculations to actually use width values when
computing downscale_w rather than copy/pasted height values.
Cc: matthew.d.roper@intel.com
Signed-off-by: Kumar, Mahesh <mahesh1.kumar@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Kumar Mahesh <mahesh1.kumar@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463439121-28974-4-git-send-email-matthew.d.roper@intel.com
don't always use 8 ddb as minimum, instead calculate using proper
algorithm.
v2: optimizations as per Matt's comments.
v3 (by Matt):
- Fix boolean logic for !fb test in skl_ddb_min_alloc()
- Adjust negative tiling format comparisons in skl_ddb_min_alloc() to
improve readability.
v4 (by Matt):
- Rebase onto recent atomic watermark changes
- Slight tweaks to code flow to make the logic more closely match the
description in the bspec.
v5 (by Matt):
- Handle minimum scanline calculation properly for 4 & 8 bpp formats.
8bpp isn't actually possible right now, but it's listed in the bspec
so I've included it here for forward compatibility (similar to how
we have logic for NV12).
v6 (by Matt):
- Calculate plane_bpp correctly for non-NV12 formats. (Mahesh)
Cc: matthew.d.roper@intel.com
Signed-off-by: Kumar, Mahesh <mahesh1.kumar@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Kumar Mahesh <mahesh1.kumar@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464713939-10440-1-git-send-email-matthew.d.roper@intel.com
We don't actually read out full plane state during driver startup (only
whether the primary plane is enabled/disabled), so all of the src/dest
rectangles are invalid at this point. However this calculation was
needless anyway since we re-calculate them from scratch on the very
first atomic transaction after boot anyway.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Kumar Mahesh <mahesh1.kumar@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463439121-28974-2-git-send-email-matthew.d.roper@intel.com
If the VBT says that a certain port should be eDP (and hence fused off
from HDMI), but in reality it isn't, we need to try and acquire the HDMI
connection instead. So only trust the VBT edp setting if we can connect
to an eDP device on that port.
Fixes: d2182a6608 (drm/i915: Don't register HDMI connectors for eDP ports on VLV/CHV)
References: https://bugs.freedesktop.org/show_bug.cgi?id=96288
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Phidias Chiang <phidias.chiang@canonical.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464766070-31623-1-git-send-email-chris@chris-wilson.co.uk
This reverts the following patches:
d55dbd06bb drm/i915: Allow nonblocking update of pageflips.
15c86bdb76 drm/i915: Check for unpin correctness.
95c2ccdc82 Reapply "drm/i915: Avoid stalling on pending flips for legacy cursor updates"
a6747b7304 drm/i915: Make unpin async.
03f476e1fc drm/i915: Prepare connectors for nonblocking checks.
2099deffef drm/i915: Pass atomic states to fbc update functions.
ee7171af72 drm/i915: Remove reset_counter from intel_crtc.
2ee004f7c5 drm/i915: Remove queue_flip pointer.
b8d2afae55 drm/i915: Remove use_mmio_flip kernel parameter.
8dd634d922 drm/i915: Remove cs based page flip support.
143f73b3bf drm/i915: Rework intel_crtc_page_flip to be almost atomic, v3.
84fc494b64 drm/i915: Add the exclusive fence to plane_state.
6885843ae1 drm/i915: Convert flip_work to a list.
aa420ddd8e drm/i915: Allow mmio updates on all platforms, v2.
afee4d8707 Revert "drm/i915: Avoid stalling on pending flips for legacy cursor updates"
"drm/i915: Allow nonblocking update of pageflips" should have been
split up, misses a proper commit message and seems to cause issues in
the legacy page_flip path as demonstrated by kms_flip.
"drm/i915: Make unpin async" doesn't handle the unthrottled cursor
updates correctly, leading to an apparent pin count leak. This is
caught by the WARN_ON in i915_gem_object_do_pin which screams if we
have more than DRM_I915_GEM_OBJECT_MAX_PIN_COUNT pins.
Unfortuantely we can't just revert these two because this patch series
came with a built-in bisect breakage in the form of temporarily
removing the unthrottled cursor update hack for legacy cursor ioctl.
Therefore there's no other option than to revert the entire pile :(
There's one tiny conflict in intel_drv.h due to other patches, nothing
serious.
Normally I'd wait a bit longer with doing a maintainer revert, but
since the minimal set of patches we need to revert (due to the bisect
breakage) is so big, time is running out fast. And very soon
(especially after a few attempts at fixing issues) it'll be really
hard to revert things cleanly.
Lessons learned:
- Not a good idea to rush the review (done by someone fairly new to
the area) and not make sure domain experts had a chance to read it.
- Patches should be properly split up. I only looked at the two
patches that should be reverted in detail, but both look like the
mix up different things in one patch.
- Patches really should have proper commit messages. Especially when
doing more than one thing, and especially when touching critical and
tricky core code.
- Building a patch series and r-b stamping it when it has a built-in
bisect breakage is not a good idea.
- I also think we need to stop building up technical debt by
postponing atomic igt testcases even longer. I think it's clear that
there's enough corner cases in this beast that we really need to
have the testcases _before_ the next step lands.
(cherry picked from commit 5a21b6650a
from drm-intel-next-queeud)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Cc: John Harrison <John.C.Harrison@Intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Dave Airlie <airlied@redhat.com>
Acked-by: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
On Loading, GuC sets PM interrupts routing (bit 31) and clears ARAT
expired interrupt (bit 9). Host turbo also updates this register
in RPS flows. This patch ensures bit 31 and bit 9 setup by GuC persists.
ARAT timer interrupt is needed in GuC for various features. It also
facilitates halting GuC and hence achieving RC6. PM interrupt routing
will not impact RPS interrupt reception by host as GuC will redirect
them.
This patch fixes igt test pm_rc6_residency that was failing with guc
load/submission enabled. Tested with SKL GuC v6.1 and BXT GuC v5.1 and v8.7.
v2: i915_irq/i915_pm decoupling from intel_guc. (ChrisW)
v3: restructuring the mask update and rebase w.r.t Ville's patch. (ChrisW)
v4: Updating the pm_intr_keep during direct_interrupts_to_guc. (Sagar)
Cc: Chris Harris <chris.harris@intel.com>
Cc: Zhe Wang <zhe1.wang@intel.com>
Cc: Deepak S <deepak.s@intel.com>
Cc: Satyanantha, Rama Gopal M <rama.gopal.m.satyanantha@intel.com>
Cc: Akash Goel <akash.goel@intel.com>
Testcase: igt/pm_rc6_residency
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Tested-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464683307-19475-1-git-send-email-sagar.a.kamble@intel.com
So far we've got one condition when DRM drivers need to defer probing
on a dual GPU system and it's coded separately into each of the relevant
drivers. As suggested by Daniel Vetter, deduplicate that code in the
drivers and move it to a new vga_switcheroo helper. This yields better
encapsulation of concepts and lets us add further checks in a central
place. (The existing check pertains to pre-retina MacBook Pros and an
additional check is expected to be needed for retinas.)
One might be tempted to check deferred probing conditions in
vga_switcheroo_register_client(), but this is usually called fairly late
during driver load. The GPU is fully brought up and ready for switching
at that point. On boot the ->probe hook is potentially called dozens of
times until it finally succeeds, and each time we'd repeat bringup and
teardown of the GPU, lengthening boot time considerably and cluttering
logfiles. A separate helper is therefore needed which can be called
right at the beginning of the ->probe hook.
Note that amdgpu currently does not call this helper as the AMD GPUs
built into MacBook Pros are only supported by radeon so far.
v2: This helper could eventually be used by audio clients as well,
so rephrase kerneldoc to refer to "client" instead of "GPU"
and move the single existing check in an if block specific
to PCI_CLASS_DISPLAY_VGA devices. Move documentation on
that check from kerneldoc to a comment. (Daniel Vetter)
v3: Mandate in kerneldoc that registration of client shall only
happen after calling this helper. (Daniel Vetter)
v4: Rebase on 412c8f7de0 ("drm/radeon: Return -EPROBE_DEFER when
amdkfd not loaded")
v5: Some Optimus GPUs use PCI_CLASS_DISPLAY_3D, make sure those are
matched as well. (Emil Velikov)
v6: The if-condition referring to PCI_BASE_CLASS_DISPLAY may be
considered a functional change. Move to a separate commit to
keep this a pure refactoring change. (Emil Velikov, Jani Nikula)
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/575885fd440c2b13c3f19ddf44360cfbbff35f50.1464685538.git.lukas@wunner.de
Rather than let the core generate usless encoder names, let's pass in
something that actually identifies the piece of hardware we're dealing
with.
v2: Use 'DSI %c' instead of 'MIPI %c' for DSI encoders (Jani)
v3: Use port_name() in DSI code since we have it
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464371966-15190-7-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Let's name our planes in a way that makes sense wrt. the spec:
- skl+ -> "plane 1A", "plane 2A", "plane 1C", "cursor A" etc.
- g4x+ -> "primary A", "primary B", "sprite A", "cursor C" etc.
- pre-g4x -> "plane A", "cursor B" etc.
v2: Rebase on top of the fixed/cleaned error paths
Use a local 'name' variable to make things easier
v3: Pass the name as a function argument to drm_universal_plane_init() (Jani)
v3: Pass the printf style string to drm_universal_plane_init()
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464371966-15190-6-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Call intel_plane_destroy() instead of drm_plane_cleanup() so that we
also free the plane struct itself when bailing out of the crtc init.
And make intel_plane_destroy() NULL tolerant to avoid having to check
for it in the caller.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464371966-15190-5-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
v2: Fix intel_crtc leak on failure to allocate the name
Use a local 'name' variable to make things easier
v3: Pass the name as a function arguemnt to drm_crtc_init_with_planes() (Jani)
v4: Pass the printf style format string to drm_crtc_init_with_planes()
v5: Drop spurious code changes
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464371966-15190-4-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Pull drm fixes from Dave Airlie:
- one IMX built-in regression fix
- a set of amdgpu fixes, mostly powerplay and polaris GPU stuff
- a set of i915 fixes all over, many cc'ed to stable.
The i915 batch contain support for DP++ dongle detection, which is
used to fix some regressions in the HDMI color depth area
* tag 'drm-fixes-v4.7-rc1' of git://people.freedesktop.org/~airlied/linux: (44 commits)
drm/amd: add Kconfig dependency for ACP on DRM_AMDGPU
drm/amdgpu: Fix hdmi deep color support.
drm/amdgpu: fix bug in fence driver fini
drm/i915: Stop automatically retiring requests after a GPU hang
drm/i915: Unify intel_ring_begin()
drm/i915: Ignore stale wm register values on resume on ilk-bdw (v2)
drm/i915/psr: Try to program link training times correctly
drm/imx: Match imx-ipuv3-crtc components using device node in platform data
drm/i915/bxt: Adjusting the error in horizontal timings retrieval
drm/i915: Don't leave old junk in ilk active watermarks on readout
drm/i915: s/DPPL/DPLL/ for SKL DPLLs
drm/i915: Fix gen8 semaphores id for legacy mode
drm/i915: Set crtc_state->lane_count for HDMI
drm/i915/BXT: Retrieving the horizontal timing for DSI
drm/i915: Protect gen7 irq_seqno_barrier with uncore lock
drm/i915: Re-enable GGTT earlier during resume on pre-gen6 platforms
drm/i915: Determine DP++ type 1 DVI adaptor presence based on VBT
drm/i915: Enable/disable TMDS output buffers in DP++ adaptor as needed
drm/i915: Respect DP++ adaptor TMDS clock limit
drm: Add helper for DP++ adaptors
...
Reject the modeset if the requested dotclock exceeds the maximum allowed
by the hardware. So far we've only checked this on gen2/3 while also
handling the double wide vs. single wide pipe selection. Extend the
check to all platforms since we have the max dotclock correctly
populated now across the board.
Testcase: igt/kms_invalid_dotclock
Cc: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464114859-15610-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
I see the main drm pull got merged, here's the first batch of fixes for
4.7 already. Fixes all around, a large portion cc: stable stuff.
[airlied: the DP++ stuff is a regression fix].
* tag 'drm-intel-next-fixes-2016-05-25' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Stop automatically retiring requests after a GPU hang
drm/i915: Unify intel_ring_begin()
drm/i915: Ignore stale wm register values on resume on ilk-bdw (v2)
drm/i915/psr: Try to program link training times correctly
drm/i915/bxt: Adjusting the error in horizontal timings retrieval
drm/i915: Don't leave old junk in ilk active watermarks on readout
drm/i915: s/DPPL/DPLL/ for SKL DPLLs
drm/i915: Fix gen8 semaphores id for legacy mode
drm/i915: Set crtc_state->lane_count for HDMI
drm/i915/BXT: Retrieving the horizontal timing for DSI
drm/i915: Protect gen7 irq_seqno_barrier with uncore lock
drm/i915: Re-enable GGTT earlier during resume on pre-gen6 platforms
drm/i915: Determine DP++ type 1 DVI adaptor presence based on VBT
drm/i915: Enable/disable TMDS output buffers in DP++ adaptor as needed
drm/i915: Respect DP++ adaptor TMDS clock limit
drm: Add helper for DP++ adaptors
Thanks to Ville Syrjälä for pointing me towards the cause of this issue.
Unfortunately one of the sideaffects of having the refclk for a DPLL set
to SSC is that as long as it's set to SSC, the GPU will prevent us from
powering down any of the pipes or transcoders using it. A couple of
BIOSes enable SSC in both PCH_DREF_CONTROL and in the DPLL
configurations. This causes issues on the first modeset, since we don't
expect SSC to be left on and as a result, can't successfully power down
the pipes or the transcoders using it. Here's an example from this Dell
OptiPlex 990:
[drm:intel_modeset_init] SSC enabled by BIOS, overriding VBT which says disabled
[drm:intel_modeset_init] 2 display pipes available.
[drm:intel_update_cdclk] Current CD clock rate: 400000 kHz
[drm:intel_update_max_cdclk] Max CD clock rate: 400000 kHz
[drm:intel_update_max_cdclk] Max dotclock rate: 360000 kHz
vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[drm:intel_crt_reset] crt adpa set to 0xf40000
[drm:intel_dp_init_connector] Adding DP connector on port C
[drm:intel_dp_aux_init] registering DPDDC-C bus for card0-DP-1
[drm:ironlake_init_pch_refclk] has_panel 0 has_lvds 0 has_ck505 0
[drm:ironlake_init_pch_refclk] Disabling SSC entirely
… later we try committing the first modeset …
[drm:intel_dump_pipe_config] [CRTC:26][modeset] config ffff88041b02e800 for pipe A
[drm:intel_dump_pipe_config] cpu_transcoder: A
…
[drm:intel_dump_pipe_config] dpll_hw_state: dpll: 0xc4016001, dpll_md: 0x0, fp0: 0x20e08, fp1: 0x30d07
[drm:intel_dump_pipe_config] planes on this crtc
[drm:intel_dump_pipe_config] STANDARD PLANE:23 plane: 0.0 idx: 0 enabled
[drm:intel_dump_pipe_config] FB:42, fb = 800x600 format = 0x34325258
[drm:intel_dump_pipe_config] scaler:0 src (0, 0) 800x600 dst (0, 0) 800x600
[drm:intel_dump_pipe_config] CURSOR PLANE:25 plane: 0.1 idx: 1 disabled, scaler_id = 0
[drm:intel_dump_pipe_config] STANDARD PLANE:27 plane: 0.1 idx: 2 disabled, scaler_id = 0
[drm:intel_get_shared_dpll] CRTC:26 allocated PCH DPLL A
[drm:intel_get_shared_dpll] using PCH DPLL A for pipe A
[drm:ilk_audio_codec_disable] Disable audio codec on port C, pipe A
[drm:intel_disable_pipe] disabling pipe A
------------[ cut here ]------------
WARNING: CPU: 1 PID: 130 at drivers/gpu/drm/i915/intel_display.c:1146 intel_disable_pipe+0x297/0x2d0 [i915]
pipe_off wait timed out
…
---[ end trace 94fc8aa03ae139e8 ]---
[drm:intel_dp_link_down]
[drm:ironlake_crtc_disable [i915]] *ERROR* failed to disable transcoder A
Later modesets succeed since they reset the DPLL's configuration anyway,
but this is enough to get stuck with a big fat warning in dmesg.
A better solution would be to add refcounts for the SSC source, but for
now leaving the source clock on should suffice.
Changes since v3:
- Move temp variable into loop
- Move checks for using_ssc_source to after we've figured out has_ck505
- Add using_ssc_source to debug output
Changes since v2:
- Fix debug output for when we disable the CPU source
Changes since v1:
- Leave the SSC source clock on instead of just shutting it off on all
of the DPLL configurations.
Cc: stable@vger.kernel.org
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Lyude <cpaul@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1464199863-9397-1-git-send-email-cpaul@redhat.com
This set of changes introduces an atomic API to the PWM subsystem. This
is influenced by the DRM atomic API that was introduced a while back,
though it is obviously a lot simpler. The fundamental idea remains the
same, though: drivers provide a single callback to implement the atomic
configuration of a PWM channel.
As a side-effect the PWM subsystem gains the ability for initial state
retrieval, so that the logical state mirrors that of the hardware. Many
use-cases don't care about this, but for others it is essential.
These new features require changes in all users, which these patches
take care of. The core is transitioned to use the atomic callback if
available and provides a fallback mechanism for other drivers.
Changes to transition users and drivers to the atomic API are postponed
to v4.8.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=sxT9
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"This set of changes introduces an atomic API to the PWM subsystem.
This is influenced by the DRM atomic API that was introduced a while
back, though it is obviously a lot simpler. The fundamental idea
remains the same, though: drivers provide a single callback to
implement the atomic configuration of a PWM channel.
As a side-effect the PWM subsystem gains the ability for initial state
retrieval, so that the logical state mirrors that of the hardware.
Many use-cases don't care about this, but for others it is essential.
These new features require changes in all users, which these patches
take care of. The core is transitioned to use the atomic callback if
available and provides a fallback mechanism for other drivers.
Changes to transition users and drivers to the atomic API are
postponed to v4.8"
* tag 'pwm/for-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (30 commits)
pwm: Add information about polarity, duty cycle and period to debugfs
pwm: Switch to the atomic API
pwm: Update documentation
pwm: Add core infrastructure to allow atomic updates
pwm: Add hardware readout infrastructure
pwm: Move the enabled/disabled info into pwm_state
pwm: Introduce the pwm_state concept
pwm: Keep PWM state in sync with hardware state
ARM: Explicitly apply PWM config extracted from pwm_args
drm: i915: Explicitly apply PWM config extracted from pwm_args
input: misc: pwm-beeper: Explicitly apply PWM config extracted from pwm_args
input: misc: max8997: Explicitly apply PWM config extracted from pwm_args
backlight: lm3630a: explicitly apply PWM config extracted from pwm_args
backlight: lp855x: Explicitly apply PWM config extracted from pwm_args
backlight: lp8788: Explicitly apply PWM config extracted from pwm_args
backlight: pwm_bl: Use pwm_get_args() where appropriate
fbdev: ssd1307fb: Use pwm_get_args() where appropriate
regulator: pwm: Use pwm_get_args() where appropriate
leds: pwm: Use pwm_get_args() where appropriate
input: misc: max77693: Use pwm_get_args() where appropriate
...
I noticed that during S4 resume BIOS incorrectly sets bits 18, 19 which
are reserved/MBZ and sets the decimal frequency fields to all 0xff in
the CDCLK register. The result is a hard lockup as display register
accesses are attempted later. Work around this by sanitizing the CDCLK
PLL/dividers the same way it's done on SKL.
While this is clearly a BIOS bug which should be fixed separately, it
doesn't hurt to check/sanitize this regardless.
v2:
- Use the same condition for VCO and CDCLK in broxton_init_cdclk as is
used in skl_init_cdclk for the same purpose.
CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464093513-16258-2-git-send-email-imre.deak@intel.com
If the CDCLK PLL isn't locked or incorrectly configured we can just
assume that it's off resulting in fully re-initializing both CDCLK PLL
and CDCLK dividers. This way the CDCLK PLL sanitization added in the
following patch can be done on BXT the same way as it's done on SKL.
v2: (Ville)
- Remove the remaining PLL specific checks from skl_sanitize_cdclk() and
depend instead on the corresponding check in skl_dpll0_update().
- Use vco == 0 instead of the corresponding boolean check in
skl_sanitize_cdclk().
CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464093513-16258-1-git-send-email-imre.deak@intel.com
This reverts the following patches:
d55dbd06bb drm/i915: Allow nonblocking update of pageflips.
15c86bdb76 drm/i915: Check for unpin correctness.
95c2ccdc82 Reapply "drm/i915: Avoid stalling on pending flips for legacy cursor updates"
a6747b7304 drm/i915: Make unpin async.
03f476e1fc drm/i915: Prepare connectors for nonblocking checks.
2099deffef drm/i915: Pass atomic states to fbc update functions.
ee7171af72 drm/i915: Remove reset_counter from intel_crtc.
2ee004f7c5 drm/i915: Remove queue_flip pointer.
b8d2afae55 drm/i915: Remove use_mmio_flip kernel parameter.
8dd634d922 drm/i915: Remove cs based page flip support.
143f73b3bf drm/i915: Rework intel_crtc_page_flip to be almost atomic, v3.
84fc494b64 drm/i915: Add the exclusive fence to plane_state.
6885843ae1 drm/i915: Convert flip_work to a list.
aa420ddd8e drm/i915: Allow mmio updates on all platforms, v2.
afee4d8707 Revert "drm/i915: Avoid stalling on pending flips for legacy cursor updates"
"drm/i915: Allow nonblocking update of pageflips" should have been
split up, misses a proper commit message and seems to cause issues in
the legacy page_flip path as demonstrated by kms_flip.
"drm/i915: Make unpin async" doesn't handle the unthrottled cursor
updates correctly, leading to an apparent pin count leak. This is
caught by the WARN_ON in i915_gem_object_do_pin which screams if we
have more than DRM_I915_GEM_OBJECT_MAX_PIN_COUNT pins.
Unfortuantely we can't just revert these two because this patch series
came with a built-in bisect breakage in the form of temporarily
removing the unthrottled cursor update hack for legacy cursor ioctl.
Therefore there's no other option than to revert the entire pile :(
There's one tiny conflict in intel_drv.h due to other patches, nothing
serious.
Normally I'd wait a bit longer with doing a maintainer revert, but
since the minimal set of patches we need to revert (due to the bisect
breakage) is so big, time is running out fast. And very soon
(especially after a few attempts at fixing issues) it'll be really
hard to revert things cleanly.
Lessons learned:
- Not a good idea to rush the review (done by someone fairly new to
the area) and not make sure domain experts had a chance to read it.
- Patches should be properly split up. I only looked at the two
patches that should be reverted in detail, but both look like the
mix up different things in one patch.
- Patches really should have proper commit messages. Especially when
doing more than one thing, and especially when touching critical and
tricky core code.
- Building a patch series and r-b stamping it when it has a built-in
bisect breakage is not a good idea.
- I also think we need to stop building up technical debt by
postponing atomic igt testcases even longer. I think it's clear that
there's enough corner cases in this beast that we really need to
have the testcases _before_ the next step lands.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Cc: John Harrison <John.C.Harrison@Intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Dave Airlie <airlied@redhat.com>
Acked-by: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
One of the uses for i915_gem_objects is pin-pointing leaks. For this, we
can compare the number of allocated objects and who owns them, a
discrepancy here often indicates a kernel bug. One allocator of unreported
objects is for backing context objects, so include those in the listing.
v2: Take filelist_mutex which requires a little dance with struct_mutex
to avoid nesting filelist_mutex inside struct_mutex.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464098023-3294-10-git-send-email-chris@chris-wilson.co.uk
struct intel_context contains two substructs, one for the legacy RCS and
one for every execlists engine. Since legacy RCS is a subset of the
execlists engine support, just combine the two substructs.
v2: Only pin the default context for legacy mode (the object only exists
for legacy, but adding i915.enable_execlists provides symmetry with the
cleanup functions).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464098023-3294-8-git-send-email-chris@chris-wilson.co.uk
Just move the kernel_context member of drm_i915_private next to the
engines it is associated with.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464098023-3294-7-git-send-email-chris@chris-wilson.co.uk
Print the context's owner (via the pid under file_priv) under debugfs.
In doing so, we must be careful that the filp is not accessed after it
is freed (notified via i915_gem_context_close).
v2: Mark the file_priv as closed.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464098023-3294-6-git-send-email-chris@chris-wilson.co.uk
Rather than have every context ask "am I owned by the kernel? pin!",
move that logic into the creator of the kernel context, in order to
improve code comprehension.
v2: Throw away the user_handle on failure to allocate the ppgtt.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464098023-3294-5-git-send-email-chris@chris-wilson.co.uk
We want to give a name to the currently anonymous per-engine struct
inside the context, so that we can assign it to a local variable and
save clumsy typing. The name we have chosen is intel_context as it
reflects the HW facing portion of the context state (the logical context
state, the registers, the ringbuffer etc).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Dave Gordon <david.s.gordon@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464098023-3294-4-git-send-email-chris@chris-wilson.co.uk
i915_gem_context_get() is a very simple wrapper around idr_find(), so
simple that it would be smaller to do the lookup inline. Also we use the
verb 'lookup' to return a pointer from a handle, freeing 'get' to imply
obtaining a reference to the context.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464098023-3294-3-git-send-email-chris@chris-wilson.co.uk
Our goal is to rename the anonymous per-engine struct beneath the
current intel_context. However, after a lively debate resolving around
the confusion between intel_context_engine and intel_engine_context, the
realisation is that the two structs target different users. The outer
struct is API / user facing, and so carries the higher level GEM
information. The inner struct is hw facing. Thus we want to name the
inner struct intel_context and the outer one i915_gem_context. As the
first step, we need to rename the current struct:
s/struct intel_context/struct i915_gem_context/
which fits much better with its constructors already conveying the
i915_gem_context prefix!
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Dave Gordon <david.s.gordon@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464098023-3294-1-git-send-email-chris@chris-wilson.co.uk
New GuC code is logging errors at runtime suspend and resume which
causes CI testing to log "orange" status. Default to not trying to
load the firmware until this is resolved.
Example of the log:
[drm] RC6 on
[drm:intel_runtime_suspend] Suspending device
[drm:host2guc_action [i915]] *ERROR* GUC: host2guc action 0x501 failed. ret=-110 status=0x00000501 response=0x40000000
...
[drm:intel_runtime_resume] Resuming device
[drm:host2guc_action [i915]] *ERROR* GUC: host2guc action 0x502 failed. ret=-110 status=0x00000502 response=0x40000000
[drm:intel_runtime_resume] Device resumed
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Dave Gordon <david.s.gordon@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Harris <chris.harris@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1464017675-12257-1-git-send-email-tvrtko.ursulin@linux.intel.com
Merge yet more updates from Andrew Morton:
- Oleg's "wait/ptrace: assume __WALL if the child is traced". It's a
kernel-based workaround for existing userspace issues.
- A few hotfixes
- befs cleanups
- nilfs2 updates
- sys_wait() changes
- kexec updates
- kdump
- scripts/gdb updates
- the last of the MM queue
- a few other misc things
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (84 commits)
kgdb: depends on VT
drm/amdgpu: make amdgpu_mn_get wait for mmap_sem killable
drm/radeon: make radeon_mn_get wait for mmap_sem killable
drm/i915: make i915_gem_mmap_ioctl wait for mmap_sem killable
uprobes: wait for mmap_sem for write killable
prctl: make PR_SET_THP_DISABLE wait for mmap_sem killable
exec: make exec path waiting for mmap_sem killable
aio: make aio_setup_ring killable
coredump: make coredump_wait wait for mmap_sem for write killable
vdso: make arch_setup_additional_pages wait for mmap_sem for write killable
ipc, shm: make shmem attach/detach wait for mmap_sem killable
mm, fork: make dup_mmap wait for mmap_sem for write killable
mm, proc: make clear_refs killable
mm: make vm_brk killable
mm, elf: handle vm_brk error
mm, aout: handle vm_brk failures
mm: make vm_munmap killable
mm: make vm_mmap killable
mm: make mmap_sem for write waits killable for mm syscalls
MAINTAINERS: add co-maintainer for scripts/gdb
...
i915_gem_mmap_ioctl relies on mmap_sem for write. If the waiting task
gets killed by the oom killer it would block oom_reaper from
asynchronous address space reclaim and reduce the chances of timely OOM
resolving. Wait for the lock in the killable mode and return with EINTR
if the task got killed while waiting.
Signed-off-by: Michal Hocko <mhocko@suse.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: David Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull drm updates from Dave Airlie:
"Here's the main drm pull request for 4.7, it's been a busy one, and
I've been a bit more distracted in real life this merge window. Lots
more ARM drivers, not sure if it'll ever end. I think I've at least
one more coming the next merge window.
But changes are all over the place, support for AMD Polaris GPUs is in
here, some missing GM108 support for nouveau (found in some Lenovos),
a bunch of MST and skylake fixes.
I've also noticed a few fixes from Arnd in my inbox, that I'll try and
get in asap, but I didn't think they should hold this up.
New drivers:
- Hisilicon kirin display driver
- Mediatek MT8173 display driver
- ARC PGU - bitstreamer on Synopsys ARC SDP boards
- Allwinner A13 initial RGB output driver
- Analogix driver for DisplayPort IP found in exynos and rockchip
DRM Core:
- UAPI headers fixes and C++ safety
- DRM connector reference counting
- DisplayID mode parsing for Dell 5K monitors
- Removal of struct_mutex from drivers
- Connector registration cleanups
- MST robustness fixes
- MAINTAINERS updates
- Lockless GEM object freeing
- Generic fbdev deferred IO support
panel:
- Support for a bunch of new panels
i915:
- VBT refactoring
- PLL computation cleanups
- DSI support for BXT
- Color manager support
- More atomic patches
- GEM improvements
- GuC fw loading fixes
- DP detection fixes
- SKL GPU hang fixes
- Lots of BXT fixes
radeon/amdgpu:
- Initial Polaris support
- GPUVM/Scheduler/Clock/Power improvements
- ASYNC pageflip support
- New mesa feature support
nouveau:
- GM108 support
- Power sensor support improvements
- GR init + ucode fixes.
- Use GPU provided topology information
vmwgfx:
- Add host messaging support
gma500:
- Some cleanups and fixes
atmel:
- Bridge support
- Async atomic commit support
fsl-dcu:
- Timing controller for LCD support
- Pixel clock polarity support
rcar-du:
- Misc fixes
exynos:
- Pipeline clock support
- Exynoss4533 SoC support
- HW trigger mode support
- export HDMI_PHY clock
- DECON5433 fixes
- Use generic prime functions
- use DMA mapping APIs
rockchip:
- Lots of little fixes
vc4:
- Render node support
- Gamma ramp support
- DPI output support
msm:
- Mostly cleanups and fixes
- Conversion to generic struct fence
etnaviv:
- Fix for prime buffer handling
- Allow hangcheck to be coalesced with other wakeups
tegra:
- Gamme table size fix"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (1050 commits)
drm/edid: add displayid detailed 1 timings to the modelist. (v1.1)
drm/edid: move displayid validation to it's own function.
drm/displayid: Iterate over all DisplayID blocks
drm/edid: move displayid tiled block parsing into separate function.
drm: Nuke ->vblank_disable_allowed
drm/vmwgfx: Report vmwgfx version to vmware.log
drm/vmwgfx: Add VMWare host messaging capability
drm/vmwgfx: Kill some lockdep warnings
drm/nouveau/gr/gf100-: fix race condition in fecs/gpccs ucode
drm/nouveau/core: recognise GM108 chipsets
drm/nouveau/gr/gm107-: fix touching non-existent ppcs in attrib cb setup
drm/nouveau/gr/gk104-: share implementation of ppc exception init
drm/nouveau/gr/gk104-: move rop_active_fbps init to nonctx
drm/nouveau/bios/pll: check BIT table version before trying to parse it
drm/nouveau/bios/pll: prevent oops when limits table can't be parsed
drm/nouveau/volt/gk104: round up in gk104_volt_set
drm/nouveau/fb/gm200: setup mmu debug buffer registers at init()
drm/nouveau/fb/gk20a,gm20b: setup mmu debug buffer registers at init()
drm/nouveau/fb/gf100-: allocate mmu debug buffers
drm/nouveau/fb: allow chipset-specific actions for oneinit()
...
Like with cdclk, the DMC is supposed to manage dbuf enabling/disabling.
Let's make sure it has correctly restored the dbuf state to enabled
when we disable the DC states.
v2: s/skl/gen9/ in function name (Imre)
Cc: Imre Deak <imre.deak@intel.com>
Suggested-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463407180-28993-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
In case the driver is initialized without active displays, we should
just drop the cdclk to the minimum frequency right off the bat. There
might not be a modeset to drop it to the minimum late rafter all.
With DMC supposedly we should always have the cdclk up and running.
The DMC will shut the DE PLL down when appropriate, so let's nuke
the related FIXMEs as well. Trying to do anything different would
go against the expectations of the DMC firmware, and we all know
how fragile the DMC firmware is.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463172100-24715-22-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Rather than having a BXT specific function to make sure the DE PLL is
enabled after disabling DC6, let's just make sure the current cdclk
is the same as what we last programmed.
Having another check in bxt_display_core_init() almost immediately after
the cdclk init seems redundant, so let's just kill that one.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463172100-24715-21-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Make bxt_set_cdclk() more readable by looking at current vs. target
DE PLL vco to determine if the DE PLL needs disabling and/or enabling.
We can also calculate the CD2X divider simply as (vco/cdclk) instead of
depending on magic numbers.
The magic numbers are still needed though, but only to map the supported
cdclk frequencies to corresponding DE PLL frequencies.
Note that w'll now program CDCLK_CTL correctly even for the bypass case.
Actually the CD2X divider should not matter in that case since the
hardware will bypass it too, but the "decimal" part should matter (if we
want to do gmbus/aux with the bypass enabled).
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463172100-24715-20-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
We'll want to store the cdclk PLL (whatever PLL that is in reality) vco
frequency somewhere on other platforms too, so let's rename the
skl_vco_freq to cdclk_pll.vco, and let's store it in kHz instead of MHz
to match most of the other clocks.
v2: Drop the spurious > vs != change (Imre)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463172100-24715-14-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
The SKL 308.57 MHz cdclk is probably 8640/28 = ~308.571 Mhz.
Similartly the 617.14 MHz cdclk is probably 8640/14 = ~617.143 MHz.
Let's use the slightly more accurate numbers. Potentially we might
change to computing all of these based on dividers, but let's
stick to the current theme for now..
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463172100-24715-13-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
SKL and BXT have the same snippets of code for enabling disabling the
DBUF. Extract those into helpers and move the calls from
init/unit_cdclk() to the display core init/init since this stuff isn't
really about cdclk. Also doing the enable twice shouldn't hurt since
you're just setting the request bit again when it was already set.
We can also toss in a few WARNs about the register values into
skl_get_dpll0_vco() now that we know that things should always be
sane there.
Flatten skl_init_cdclk() while at it.
v2: s/skl/gen9/ in function names (Imre)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463172100-24715-12-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Currently we initialize cdclk on SKL from two different places,
depending on whether it's during driver init or resume. Let's
unify it to happen from the same place always, and that place will be
the display core init function.
To do this we first run through the cdclk sanitation code, which will
first verify that the PLL is programmed correctly, after which we can
read out the current cdclk frequency, and once the cdclk is known we
verify that the cdclk "decimal" frequency is programmed correctly. If
any of these fail we will force a cdclk change, and to be safe we also
force the PLL to be turned off and on again. If the sanitation step
didn't notice anything amiss, we'll skip the cdclk programming which
will prevent cdclk reprogramming when the displays might be active.
We can also toss in a few WARNs about the register values into
skl_update_dpll0() since we now know that the PLL state should
always be sane when that function is called.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463172100-24715-11-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Now that skl_vco_freq tracks the actual DPLL0 vco frequency, we'll need
something that keeps track of which vco frequency we want to use in case
the current vco is 0. This would be important across supend/resume since
we'll disable DPLL0 around those parts.
We'll also update our idea of max cdclk/dotclock when the preferred
vco changes. That could happen if out initial guess was wrong, and
later eDP would force us to change it. One issue here could be that
changing the max dotclock could cause our mode list to change during
next time the displays get probed. But I don't see a good way to avoid
that, except perhaps by allowing either vco frequency to be used as
needed. But the docs suggest that such usage wasn't really inteded.
Also need to make sure we don't update our max_cdclk value before we
have a preferred vco value, which means moving that to happen after
the cdclk sanitation.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463172100-24715-9-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
In case we originally guessed wrong which lcpll vco frequency to use,
we will need to shut down the pll and restart it when reprogamming the
cdclk.
This also allows us to track the actual vco frequency in dev_priv
instead of just a guess.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463172100-24715-8-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Currently we're trying to guess which lcpll vco frequency is used
use based on the cdclk. That doesn't work for cdclk==540 since
both vco frequencies can generate a 540 Mhz output. Let's stop
guessing and just read the actual vco frequency from the
hardware.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463172100-24715-6-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Shared plls won't get assigned until the .compute_clocks() hook gets
called, which happens from the crtc .atomic_check hook. That's too late
as the cdclk computation has already happened. So let's move the DPLL0
VCO computation into intel_dp_compute_config() so that it's done when
the cdclk computation happens. Also only do it for eDP since we only
pick DPLL0 for eDP.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463172100-24715-4-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
WARNING: Using ChromeOS with an eDP panel and a 4K@60 DP monitor connected
to DDI1 the system will hard hang during a cold boot. Occurs when DDI1
is enabled when the cdclk is less then required. DP connected to DDI2
and HPD on either port works correctly.
Set cdclk based on the max required pixel clock based on VCO
selected. Track boot vco instead of boot cdclk.
The vco is now tracked at the atomic level and all CRTCs updated if
the required vco is changed. Not tested with eDP v1.4 panels that
require 8640 vco due to availability.
V1: initial version
V2: add vco tracking in intel_dp_compute_config(), rename
skl_boot_cdclk.
V3: rebase, V2 feedback not possible as encoders are not aware of
atomic.
V4: track target vco is atomic state. modeset all CRTCs if vco changes
V5: rename atomic variable, cleaner if/else logic, use existing vco if
encoder does not return a new vco value. check_patch.pl cleanup
V6: simplify logic in intel_modeset_checks.
V7: reorder an IF for readability and whitespace fix.
V8: use dev_cdclk for tracking new cdclk during atomic
V9: correctly handle vco 8640 when crtcs==0
V10: Clean up if else in crtcs==0
V11: Rebase for new intel_dpll_mgr.c
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Clint Taylor <clinton.a.taylor@intel.com>
[vsyrjala: rebased due to churn]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463172100-24715-3-git-send-email-ville.syrjala@linux.intel.com
commit 4e5ca60fd3 ("drm/i915: Use ilk_max_pixel_rate() for BXT cdclk calculation")
tried to change BXT to use ilk_max_pixel_rate() to compute the
pipe pixel rate. I failed to notice that there was another place
in the state readout code that needs the same treatment. So let's
change that one too.
Should probably just change things to always compuyte the pipe pixel
rates, instead of just doing on platforms that can change cdclk
dynamically. But for now let's just move BXT fully over to the
side that uses ilk_pipe_pixel_rate().
Cc: Jani Nikula <jani.nikula@intel.com>
Fixes: 4e5ca60fd3 ("drm/i915: Use ilk_max_pixel_rate() for BXT cdclk calculation")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463172100-24715-2-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Current intel_opregion_init is called during the driver registration
phase and intel_opregion_fini from the unregistration phase. Rename the
functions so that this is clear from their names. The phases tell us
what we expect the existing hw state to be, e.g. whether interrupts are
still enabled etc.
It should be noted that the opregion init/fini routines are asymmetric
and this is carried across into their new names. Indeed, their new names
make it even clearer that perhaps all is not well in the opregion
suspend/resume sequence (as well in the module unload).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464012490-30961-2-git-send-email-chris@chris-wilson.co.uk
Reviewed-by: Jani Nikula <jani.nikula@linux.intel.com>
Prefer passing struct drm_i915_private to internal interfaces as this
saves us having to dance between drm_device and our native struct. The
savings hare are small (only 70 bytes of unrequired dancing), but
progressive!
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464012490-30961-1-git-send-email-chris@chris-wilson.co.uk
Reviewed-by: Jani Nikula <jani.nikula@linux.intel.com>
