Add basic support for STM32H743 MCU and his eval board.
The STMicrolectornics's STM32H743 MCU is based on Cortex-M7 core
running up to @400MHz with 2MB internal flash and 1MB internal RAM.
For more details see:
Documentation/arm/stm32/stm32h743-overview.txt
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Add pinmux for rx,tx,cts and rts lines of uart0. This will enable uart0
to use hardware flow control.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable support for W25Q64CVSSIG which is a Winbond 64 Mbit SPI NOR.
At boot you will see the following message:
m25p80 spi1.0: found s25fl064k, expected w25q64
This is because the JEDEC ID for this chip is the same as s25fl064k.
However, this should be harmless since both chips are essentially the
same.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
After the ti-cpufreq driver has been added, we can now drop the
operating-points table present in dra7.dtsi for the cpu and add an
operating-points-v2 table with all OPPs available for all silicon
revisions. Also add necessary data for use by ti-cpufreq to selectively
enable the appropriate OPPs at runtime as part of the operating-points
table.
As we now need to define voltage ranges for each OPP, we define the
minimum and maximum voltage to match the ranges possible for AVS class0
voltage as defined by the DRA7/AM57 Data Manual, with the exception of
using a range for OPP_OD based on historical data to ensure that SoCs
from older lots still continue to boot, even though more optimal voltages
are now the standard. Once an AVS Class0 driver is in place it will be
possible for these OPP voltages to be adjusted to any voltage within the
provided range.
Information from SPRS953, Revised December 2015.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
eviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The operatings-points-v2 table for am4372 was merged before any user of
it was present in the kernel and before the binding had been finalized.
The new ti-cpufreq driver and binding expects the platform specific
properties to be part of the operating-points-v2 table rather than the
cpu node so let's move them there as the only user is the ti-cpufreq
driver.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
eviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Although all PG2.0 silicon may not support 1GHz OPP for the MPU, older
Beaglebone Blacks may have PG2.0 silicon populated and these particular
parts are guaranteed to support the OPP, so enable it for PG2.0 on
am335x-boneblack only.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
eviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
After the ti-cpufreq driver has been added, we can now drop the
operating-points table present in am33xx.dtsi for the cpu and add an
operating-points-v2 table with all OPPs available for all silicon
revisions. Also add necessary data for use by ti-cpufreq to selectively
enable the appropriate OPPs at runtime as part of the operating-points
table.
Information from AM335x Data Manual, SPRS717i, Revised December 2015,
Table 5-7.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
eviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the SATA controller node to the dm8168-evm device tree.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This board has an external oscillator supplying the reference clock
signal for SATA. Its rate is fixed at 100Mhz. Add a corresponding
device tree node.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch set HSE_RTC clock frequency to 1 MHz, as the clock supplied to
the RTC must be 1 MHz.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
This patch lists STM32F7's RCC numeric constants.
It will be used by clock and reset drivers, and DT bindings.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
This patch enables clocks for STM32F746 MCU.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Add appropriate properties to devices in the Linksys WRT AC Series for the
mvneta driver to use hardware buffer management.
Also update "soc" ranges property and set the status of bm and bm-bppi
to "okay" (SRAM).
Signed-off-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The Nokia N950 and N9 have a wl1271 (with nokia bootloader) bluetooth
module connected to second UART.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add bcm2048 node and its system clock to the N900 device tree file.
Apart from that a reference to the new clock has been added to
wl1251 (which uses it, too).
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The unit address for the msi controller is not valid as there is no reg
property, so remove it. Also, msi-controller is the preferred node name.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: Jon Mason <jonmason@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Acked-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This adds baud rate, parity & number of data bits. It's required to get
serial working correctly.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
So far every Northstar device we have seen was using the same serial
console params (115200n8). It probably make the most sense to put it in
some proper dtsi files instead of repeating over and over for every
single device. As different boards may use different bootloaders it
seems the safest idea is to use board specific dtsi files.
Just in case some vendor decides to use different UART (parameters) this
can be always easily overwritten.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Droid 4 has two modems, mdm6600 and w3glte. Both are on the HCI USB
controller.
Let's add a configuration for the HCI so the modems can be enabled.
Note that the modems still need additional GPIO based configuration.
Cc: devicetree@vger.kernel.org
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Tested-by: Sebastian Reichel <sre@kernel.org>
[tony@atomide.com: left out url]
Signed-off-by: Tony Lindgren <tony@atomide.com>
The LCD panel on droid 4 is a command mode LCD. The binding follows
the standard omapdrm binding and the changes needed for omapdrm command
mode panels are posted separately.
Cc: devicetree@vger.kernel.org
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can get HDMI working as long as the 5V regulator is on. There is
probably an encoder chip there too, but so far no idea what it might be.
Let's keep the 5V HDMI regulator always enabled for now as otherwise we
cannot detect the monitor properly.
Cc: devicetree@vger.kernel.org
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add tmp105 sensor for droid 4. This can be used with modprobe
lm75.ko and running sensors from lm-sensors package. Note that
the lm75.c driver does not yet support alert interrupt but
droid 4 seems to be wired for it.
Cc: devicetree@vger.kernel.org
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Tested-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Droid 4 has a GPIO line that we can use with CONFIG_POWER_RESET_GPIO.
It is probably connected to the CPCAP PMIC, and seems to power down
the whole device taking power consumption to zero based on what
I measured.
Cc: devicetree@vger.kernel.org
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Tested-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The TI LMU driver has not yet been merged, but the device
tree binding for TI LMU drivers has been acked already
earlier by Rob Herring <robh+dt@kernel.org>. So it should
be safe to apply to cut down the number of pending patches.
Cc: devicetree@vger.kernel.org
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Acked-by: Milo Kim <milo.kim@ti.com>
Tested-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This commit enable DMA-based transfers for SD/eMMC card adapters
and reduce number of interrupts produced by SD-card/eMMC-card
adapters.
Sometimes interrupts from SD-card/eMMC-card adapters running in
PIO mode blocks execution of hrtimers and I2S DMA callbacks for
a long periods (100 ms or more).
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
[moved dma properties to rk3xxx.dtsi and added sdio dma]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The binding should state "cortina,gemini-gpio", "faraday,ftgpio010"
stating the full name of the IP part.
Cc: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
According to [0] pointed out by Marc Zyngier in a report about a
similar error message, PPIs 11 and 13 are edge triggered on
Cortex-A9 socs including the rk3066 and rk3188 which currently
mark them as level triggered.
Until some time ago the gic did not care but commit 992345a58e
("irqchip/gic: WARN if setting the interrupt type for a PPI fails")
introduced a warning for that case.
Fix the warning on these socs by describing the interrupts correctly
and also using the binding constants for easier reading in the future.
[0] http://infocenter.arm.com/help/topic/com.arm.doc.ddi0407f/CCHEIGIC.html
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Cleanup:
* Drop superfluous status update for frequency override on various boards
* Always use status "okay" to enable devices on porger board
* Add INTC-SYS clock to device tree of various SoCs
* Tidyup Audio-DMAC channel for DVC on r8a779[013] SoCs
* Remove unit-address and reg from integrated cache on various SoCs
* Switch from ARCH_SHMOBILE_MULTI to ARCH_RENESAS
* Fix SCIFB0 dmas indentation on r8a774[35] SoCs
Enhancements:
* Add watchdog timer to r7s72100 SoC
* Update sdhi clock bindings on r7s72100 SoC
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2cA1
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt-for-v4.12' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Renesas ARM Based SoC DT Updates for v4.12
Cleanup:
* Drop superfluous status update for frequency override on various boards
* Always use status "okay" to enable devices on porger board
* Add INTC-SYS clock to device tree of various SoCs
* Tidyup Audio-DMAC channel for DVC on r8a779[013] SoCs
* Remove unit-address and reg from integrated cache on various SoCs
* Switch from ARCH_SHMOBILE_MULTI to ARCH_RENESAS
* Fix SCIFB0 dmas indentation on r8a774[35] SoCs
Enhancements:
* Add watchdog timer to r7s72100 SoC
* Update sdhi clock bindings on r7s72100 SoC
* tag 'renesas-dt-for-v4.12' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (31 commits)
ARM: dts: silk: Drop superfluous status update for frequency override
ARM: dts: alt: Drop superfluous status update for frequency override
ARM: dts: gose: Drop superfluous status update for frequency override
ARM: dts: porter: Drop superfluous status update for frequency override
ARM: dts: koelsch: Drop superfluous status updates for frequency overrides
ARM: dts: lager: Drop superfluous status update for frequency override
ARM: dts: marzen: Drop superfluous status update for frequency override
ARM: dts: bockw: Drop superfluous status update for frequency override
ARM: dts: porter: Always use status "okay" to enable devices
ARM: dts: r8a7793: Add INTC-SYS clock to device tree
ARM: dts: r8a7793: Tidyup Audio-DMAC channel for DVC
ARM: dts: r8a7791: Tidyup Audio-DMAC channel for DVC
ARM: dts: r8a7794: Add INTC-SYS clock to device tree
ARM: dts: r8a7792: Add INTC-SYS clock to device tree
ARM: dts: r8a7791: Add INTC-SYS clock to device tree
ARM: dts: r8a7790: Add INTC-SYS clock to device tree
ARM: dts: r8a73a4: Add INTC-SYS clock to device tree
ARM: dts: r7s72100: Add watchdog timer
ARM: dts: r8a7790: Tidyup Audio-DMAC channel for DVC
ARM: dts: r8a7794: Remove unit-address and reg from integrated cache
...
Signed-off-by: Olof Johansson <olof@lixom.net>
The moxart interrupt line flags were not respected in previous
driver: instead of assigning them per-consumer, a fixes mask
was set in the controller.
With the migration to a standard Faraday driver we need to
set up and handle the consumer flags correctly. Also remove
the Moxart-specific flags when switching to using real consumer
flags.
Extend the register window to 0x100 bytes as we may have a few
more registers in there and it doesn't hurt.
Tested-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Allow including of dtsi files in an architecture-independent manner.
Some dtsi files may be shared between architectures and one suggestion
was to have symlinks and let these includes get accessed via a
#include <arm64/foo.dtsi>
So add the necessary symlinks for arm32.
Suggested-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
This adds the Gemini power controller to the SoC DTSI
file.
Cc: Janos Laube <janos.dev@gmail.com>
Cc: Paulius Zaleckas <paulius.zaleckas@gmail.com>
Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Adds crypto hardware (SPU) to Northstar Plus device tree file.
Signed-off-by: Steve Lin <steven.lin1@broadcom.com>
Acked-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Adds mailbox / PDC to NSP device tree. Needs new compatibility string
to differentiate from NS2 version.
Signed-off-by: Steve Lin <steven.lin1@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Adding ethernet aliases. These are used, for example, by bootloaders,
to modify the MAC addresses in the device tree.
Signed-off-by: Steve Lin <steven.lin1@broadcom.com>
Acked-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This is BCM47081A0 based home router with BCM43217 and BCM4352 wireless
chipsets.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The i2c device tree entry should be disabled by default to match the
current convention in other device tree files. Similarily, enable it on
the XMC board, where it is being used.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add the EHCI and OHCI entries to the Northstar Plus device tree files.
Signed-off-by: Yendapally Reddy Dhananjaya Reddy <yendapally.reddy@broadcom.com>
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add I2C support to the bcm5301x Device Tree. Since no driver changes
are needed to enable this hardware, only the device tree changes are
required to make this functional.
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add support for the ARM TWD Watchdog to the bcm5301x device tree. The
ARM TWD timer allocated the register space for the WDT, so this patch
necessitated shrinking that. Also, the GIC masks were added for these.
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
GIC_PPI flags were misconfigured for the timers, resulting in errors
like:
[ 0.000000] GIC: PPI11 is secure or misconfigured
Changing them to being edge triggered corrects the issue
Suggested-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Fixes: d27509f1 ("ARM: BCM5301X: add dts files for BCM4708 SoC")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add OneNAND node for IGEP and leave it disabled by default. It is up
to bootloader to enable proper node. Timing just works, but values are
copied over from N900 as I was unable to find chip datasheet.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the dmas and dma-names properties to support HDMI audio.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Add the Altera Arria10 System Resource Reset Controller to the MFD
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
---
v2 change commit header to ARM: dts: socfpga.
dw-mmc got its reset-properties specified, so add the softresets
for it in rk3228/rk3229.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviwed-by: Shawn Lin <shawn.lin@rock-chips.com>
dw-mmc got its reset-properties specified, so add the softresets
for it in rk3066/rk3188.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviwed-by: Shawn Lin <shawn.lin@rock-chips.com>
dw-mmc got its reset-properties specified, so add the softresets
for it in rk3036.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviwed-by: Shawn Lin <shawn.lin@rock-chips.com>
dw-mmc got its reset-properties specified, so add the softresets
for it in rk3288.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviwed-by: Shawn Lin <shawn.lin@rock-chips.com>
The scif_clk device node is already enabled in r8a7794.dtsi, so there is
no need to update its status again.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The scif_clk device node is already enabled in r8a7794.dtsi, so there is
no need to update its status again.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The scif_clk device node is already enabled in r8a7793.dtsi, so there is
no need to update its status again.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The pcie_bus_clk device node is already enabled in r8a7791.dtsi, so
there is no need to update its status again.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The scif_clk and pcie_bus_clk device nodes are already enabled in
r8a7791.dtsi, so there is no need to update their statuses again.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The scif_clk device node is already enabled in r8a7790.dtsi, so there is
no need to update its status again.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The scif_clk device node is already enabled in r8a7779.dtsi, so there is
no need to update its status again.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The scif_clk device node is already enabled in r8a7778.dtsi, so there is
no need to update its status again.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
While status "ok" does work, the canonical form is "okay", so update the
few places that used the former.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Link the ARM GIC to the INTC-SYS module clock, and add it to the "always
on" PM Domain, so it can be power managed using that clock.
Note that currently the GIC-400 driver doesn't support module clocks nor
Runtime PM, so this must be handled as a critical clock.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This devicetree is simply based on the board file in
arch/arm/mach-gemini/board-wbd222.c and contain the
equivalent platform data, mainly just moving the GPIOs
from the global numberspace to explicitly reference their
parent GPIO.
Cc: Janos Laube <janos.dev@gmail.com>
Cc: Paulius Zaleckas <paulius.zaleckas@gmail.com>
Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This devicetree is simply based on the board file in
arch/arm/mach-gemini/board-wbd111.c and contain the
equivalent platform data, mainly just moving the GPIOs
from the global numberspace to explicitly reference their
parent GPIO.
Cc: Janos Laube <janos.dev@gmail.com>
Cc: Paulius Zaleckas <paulius.zaleckas@gmail.com>
Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This devicetree is simply based on the board file in
arch/arm/mach-gemini/board-rut1xx.c and contain the
equivalent platform data, mainly just moving the GPIOs
from the global numberspace to explicitly reference their
parent GPIO.
Cc: Janos Laube <janos.dev@gmail.com>
Cc: Paulius Zaleckas <paulius.zaleckas@gmail.com>
Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This devicetree is simply based on the board file in
arch/arm/mach-gemini/board-nas4220b.c and contain the
equivalent platform data, mainly just moving the GPIOs
from the global numberspace to explicitly reference &gpio1.
Cc: Janos Laube <janos.dev@gmail.com>
Cc: Paulius Zaleckas <paulius.zaleckas@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds a device tree for the Gemini SoC and the ITian
Square One SQ201 board that has been my testing target
for Gemini device tree support.
Cc: Janos Laube <janos.dev@gmail.com>
Cc: Paulius Zaleckas <paulius.zaleckas@gmail.com>
Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The eMMC devices on UniPhier boards are generally used in the 8-bit
mode. So, DAT4-7 pins should be controlled.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
These UniPhier DT files are fine as long as they are compiled in the
Linux build system. It is true that Linux is the biggest user of
DT, but DT is project neutral from its concept. DT files are often
re-used for other projects. Especially for the UniPhier platform,
these DT files are re-used for U-Boot as well.
If I feed these DT files to the FDTGREP tool in U-Boot, it complains
about the node order.
FDTGREP spl/u-boot-spl.dtb
Error at 'fdt_find_regions': FDT_ERR_BADLAYOUT
/aliases node must come before all other nodes
Given that DT is not very sensitive to the order of nodes, this is a
problem of FDTGREP. I filed a bug report a year ago, but it has not
been fixed yet.
Differentiating DT is painful. So, I am up-streaming the requirement
from the down-stream project.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Current Audio-DMAC is assigned "rx" as Audio-DMAC0, "tx" as Audio-DMAC1.
Thus, DVC "tx" should be assigned as Audio-DMAC1, instead of Audio-DMAC0.
Because of this, current platform board (using SRC/DVC/SSI)
Playback/Capture both will use same Audio-DMAC0
(but it depends on audio data path).
First note is that this "rx" and "tx" are from each IP point,
it doesn't mean Playback/Capture.
Second note is that Audio DMAC assigned on DT is only for
Audio-DMAC, Audio-DMAC-peri-peri has no entry.
=> Audio-DMAC
-> Audio-DMAC-peri-peri
-- HW connection
Playback case
[Mem] => [SRC]--[DVC] -> [SSI]--[Codec]
rx ~~~~~~~~~~~~
Capture
[Mem] <= [DVC]--[SRC] <- [SSI]--[Codec]
tx ~~~~~~~~~~~~
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Current Audio-DMAC is assigned "rx" as Audio-DMAC0, "tx" as Audio-DMAC1.
Thus, DVC "tx" should be assigned as Audio-DMAC1, instead of Audio-DMAC0.
Because of this, current platform board (using SRC/DVC/SSI)
Playback/Capture both will use same Audio-DMAC0
(but it depends on audio data path).
First note is that this "rx" and "tx" are from each IP point,
it doesn't mean Playback/Capture.
Second note is that Audio DMAC assigned on DT is only for
Audio-DMAC, Audio-DMAC-peri-peri has no entry.
=> Audio-DMAC
-> Audio-DMAC-peri-peri
-- HW connection
Playback case
[Mem] => [SRC]--[DVC] -> [SSI]--[Codec]
rx ~~~~~~~~~~~~
Capture
[Mem] <= [DVC]--[SRC] <- [SSI]--[Codec]
tx ~~~~~~~~~~~~
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Link the ARM GIC to the INTC-SYS module clock, and add it to the "always
on" PM Domain, so it can be power managed using that clock.
Note that currently the GIC-400 driver doesn't support module clocks nor
Runtime PM, so this must be handled as a critical clock.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Link the ARM GIC to the INTC-SYS module clock, and add it to the "always
on" PM Domain, so it can be power managed using that clock.
Note that currently the GIC-400 driver doesn't support module clocks nor
Runtime PM, so this must be handled as a critical clock.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Link the ARM GIC to the INTC-SYS module clock, and add it to the "always
on" PM Domain, so it can be power managed using that clock.
Note that currently the GIC-400 driver doesn't support module clocks nor
Runtime PM, so this must be handled as a critical clock.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Link the ARM GIC to the INTC-SYS module clock, and add it to the "always
on" PM Domain, so it can be power managed using that clock.
Note that currently the GIC-400 driver doesn't support module clocks nor
Runtime PM, so this must be handled as a critical clock.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Link the ARM GIC to the INTC-SYS module clock and the C4 power domain,
so it can be power managed using that clock in the future.
Note that currently the GIC-400 driver doesn't support module clocks nor
Runtime PM, so this must be handled as a critical clock.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add watchdog timer support for RZ/A1.
For the RZ/A1, the only way to do a reset is to overflow the WDT, so this
is useful even if you don't need the watchdog functionality.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Such a trigger doesn't exist in Linux and is not needed as LED is being
turned off by default. This could cause errors in LEDs core code when
trying to set default trigger.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Such a trigger doesn't exist in Linux and is not needed as LED is being
turned off by default. This could cause errors in LEDs core code when
trying to set default trigger.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The Marvell 98dx3236 SoC only has a single PCIe x1 interface. The "Port
0.1 MEM" range was errantly kept when creating a specific dts for the
SoC.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Previously the coreclk binding for the 98dx3236 SoC was inherited from
the armada-370/xp. This block is present in as much as it is possible to
read from the register location without causing any harm. However the
actual sampled at reset values are reflected in the DFX block.
Moving the binding to the DFX block enables support for different clock
strapping options in hardware.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The Marvell datasheets refer to the integrated CPU as "Armada-XP". In
reality there are a number of differences to the actual Armada-XP so
rather than including armada-xp.dtsi and disabling many of the IP
blocks. Include armada-370-xp.dtsi and add the required nodes.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Rather than having a separate node for the dfx server add a reg property
to the parent node. This give some compatibility with the Marvell
supplied SDK.
As no upstream driver currently exists for this block and support for
this SoC is still quite fresh in the kernel it should not be necessary
to retain a backwards compatible binding.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
In others board we have the sata led set to function
with the sata led trigger by default.
This patch makes the same for these board that have sata
led but get disabled by not associating it to any trigger.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The mbus binding had been extended more than two years ago, but the
device tree files for Armada 38x didn't change.
Adding this third entry will allow the mbus going to suspend which was
the last thing preventing the SoC going to standby mode
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The Linksys WRT1900ACS (Shelby) is another Armada 385 based router in
the Linksys WRT AC Series which got released in October 2015.
The file armada-385-linksys-shelby.dts is taken from OpenWrt as-is and
originally authored by Imre Kaloz.
URL: 8466384db1/target/linux/mvebu/files/arch/arm/boot/dts/armada-385-linksys-shelby.dts
CC: Imre Kaloz <kaloz@openwrt.org>
Signed-off-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This commit adds the device tree description for the Synology DS116 NAS.
It is a one-bay NAS powered by a Marvell Armada 385 at 1.866 GHz. The
device features the following items :
- 1 GB DDR3 RAM
- a 8MB SPI flash
- 2 USB3 ports, power-controlled via a GPIO for each
- 1 gigabit ethernet interface connected over SGMII to a 88e1514 phy
- a single SATA port, power-controlled via a GPIO
- a battery-powered RTC
- one UART connected to the serial console (2mm connector on board)
- the Tx line of the second UART connected to a PIC microcontroller
dealing with beep, reset, power-off and LED blinking (9600 Bps)
- some of the front-panel LEDs are connected to GPIOs, one is directly
connected to the SATA link to report disk activity.
- a GPIO-controlled fan (3 bits for 7 speeds and OFF)
With this DTS, my NAS is 100% functional starting with kernel 4.9.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
As was done with Armada XP, add node labels to Armada 38x common and SoC
specific nodes to make them easier to reference in board device trees.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Extend the vpif node with an output port with a single channel.
NOTE: this is still mostly just hardware description - the actual
driver is registered using pdata-quirks. We need the node however
for correct pin control function selection.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
We need the expander to be probed to allow the VPIF controller to
receive interrupts from the video decoder.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Add a new pinctrl sub-node for vpif display pins. Move VP_CLKIN3 and
VP_CLKIN2 to the display node where they actually belong (vide section
36.2.2 of the OMAP-L138 technical reference manual).
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The da850-evm dts file contains whitespace errors in the vpif node.
This patch fixes them.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
