This patch adds simple-card support to the i.MX SoCs.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
This patch adds support for the Freescale (Motorola) i.MX1 ADS board.
This change is intended to further remove non-DT support for this board.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Add USB support for Freescale Vybrid tower. The USB hosts over-current
protection signal is not connected to the PHY's over- current
protection, hence we need to disable it.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Add USB support for Colibri VF61 modules. The Colibri standard pinout
defines a pin for USB over-current. However, due to lack of pinmux
options, the USB hosts over-current protection signal of the Colibri
standard could not be connected to the PHY's over-current protection.
Hence we need to disable the over-current functionality of the USB
controller.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Add device tree node for usbmisc which controls the non-core USB
registers. This is required to use the property to disable the over-
current detection.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
This adds USB PHY and USB controller nodes. Vybrid SoCs have two
independent USB cores which each supports DR (dual role). However,
real OTG is not supported since the OTG ID pin is not available.
The PHYs are located within the anadig register range, hence we need
to change the length of the anadig registers.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
[ukl: rebase from ancient kernel version]
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The preloaded script addresses on imx25 and imx35 are different, so
imx25 is not compatible with imx35-sdma unless a custom firmware is
loaded.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
This patch adds basic devicetree template for i.MX1 based SoCs.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Everything in the PCI specification assumes devices to be
enumerable on startup. This is only possible if they have
power available.
A future improvement may allow this regulator to be switched
off for D3hot and D3cold power states, but there is a lot
of work to do the pcie host controller side for this to work.
To keep things simple always enable the regulator for now.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The Colibri VF61 is a module which needs a carrier board to actually
run. Different carrier board have different hardware support, hence
we should reflect this in the device tree files. This patch adds the
Colibri Evaluation Board, which supports almost all peripherals
defined in the Colibri standard.
Also align the compatible naming, file splitting and file naming with
the scheme which was choosen for the Tegra based modules.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
This was added by:
Commit 8128c4f36 ("ARM: dts: vf610-twr: Add simple-card support.")
This useless property may cause some confusions for users.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Here's the weekly batch of fixes from arm-soc.
The delta is a largeish negative delta, due to revert of SMP support for Broadcom's
STB SoC -- it was accidentally merged before some issues had been addressed, so they
will make a new attempt for 3.18. I didn't see a need for a full revert of the whole
platform due to this, we're keeping the rest enabled.
The rest is mostly:
* A handful of DT fixes for i.MX (Hummingboard/Cubox-i in particular)
* Some MTD/NAND fixes for OMAP
* Minor DT fixes for shmobile
* Warning fix for UP builds on vexpress/spc
There's also a couple of patches that wires up hwmod on TI's DRA7 SoC
so it can boot. Drivers and the rest had landed for 3.17, and it's small
and isolated so it made sense to pick up now even if it's not a bugfix.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJUA1uwAAoJEIwa5zzehBx3dV8QAJv/6OcFofqWPqSapCdcCTkU
o9o+QxzTY4Fo4GDyTboLwvY2EE7aFKohiekKGoHHT+fXXR4n+/Xe5Dq58DijdZ0q
xUksd1h1ZuqzbWqT+1fyrlgJt3jOmQ1vzbBVpWA4tN1RUKJekU+ZF0oCAAdDwbaf
O925etd77+ij0euJ/l06fR9YUYIY23mufG+SELke5S7xS9T1sVFWcluf/z+y57qc
hxF6Uc5r4LOY4pFKYgjvsu3R7KPD4DANCiSYUvjS5sIWrJ3xenkyHVMxFEyQ5Tz+
TCrT8rXx3Ue7AlNMztY5P1dTmYftwJhWy6p/8J8UqPJ6ip633FWrhTfKHmLIR3lC
VkMYroFeg4Fp/YvFENeBe9QUbg0Xb920oZoDQA4SwkZJkQlWafYsOy4bLKSyMQGQ
nKcnyxeP2q5YaStTZMSNQ4xwT9yo3dwBllYGSbXUiTk0VJ3TX9jEMg6StvRM0YHG
sT8XKufqIAJugNZZsGtGyBLO6f8BbPVgFICvEVetgjMWHl9iGNVDbeqbYvQ6A8NL
TTqJUK7CXkNgQGX2rB7txSgR3XoaWU0rWjSnSXy2Xgtb/pd/jZYLicEY8Wd4Q1qp
Ww2misiX4viMxcD6AWiDUj1mcciSh915h1po5zZbLMTRp4qfuqh1BfSvPY/fh5DD
LKXAwm3PyL9+QrknP3//
=/AD8
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Here's the weekly batch of fixes from arm-soc.
The delta is a largeish negative delta, due to revert of SMP support
for Broadcom's STB SoC -- it was accidentally merged before some
issues had been addressed, so they will make a new attempt for 3.18.
I didn't see a need for a full revert of the whole platform due to
this, we're keeping the rest enabled.
The rest is mostly:
- a handful of DT fixes for i.MX (Hummingboard/Cubox-i in particular)
- some MTD/NAND fixes for OMAP
- minor DT fixes for shmobile
- warning fix for UP builds on vexpress/spc
There's also a couple of patches that wires up hwmod on TI's DRA7 SoC
so it can boot. Drivers and the rest had landed for 3.17, and it's
small and isolated so it made sense to pick up now even if it's not a
bugfix"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (23 commits)
vexpress/spc: fix a build warning on array bounds
ARM: DRA7: hwmod: Add dra74x and dra72x specific ocp interface lists
ARM: DRA7: Add support for soc_is_dra74x() and soc_is_dra72x() variants
MAINTAINERS: catch special Rockchip code locations
ARM: dts: microsom-ar8035: MDIO pad must be set open drain
ARM: dts: omap54xx-clocks: Fix the l3 and l4 clock rates
ARM: brcmstb: revert SMP support
ARM: OMAP2+: hwmod: Rearm wake-up interrupts for DT when MUSB is idled
ARM: dts: Enable UART wake-up events for beagleboard
ARM: dts: Remove twl6030 clk32g "regulator"
ARM: OMAP2+: omap_device: remove warning that clk alias already exists
ARM: OMAP: fix %d confusingly prefixed with 0x in format string
ARM: dts: DRA7: fix interrupt-cells for GPIO
mtd: nand: omap: Fix 1-bit Hamming code scheme, omap_calculate_ecc()
ARM: dts: omap3430-sdp: Revert to using software ECC for NAND
ARM: OMAP2+: GPMC: Support Software ECC scheme via DT
mtd: nand: omap: Revert to using software ECC by default
ARM: dts: hummingboard/cubox-i: change SPDIF output to be more descriptive
ARM: dts: hummingboard/cubox-i: add USB OC pinctrl configuration
ARM: shmobile: r8a7791: add missing 0x0100 for SDCKCR
...
This patch series updates the device tree vendor prefix for
Dialog Semiconductor.
Various methods are currently used throughout the kernel: 'diasemi',
'dialog' and 'dlg'. Others have also been suggested.
This patch set aims to consolidate the usage of the vendor prefix to
use a common standard. The prefix 'dlg' is used.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
(and a sneaky document addition that slipped from the previous pull-request)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=DaB2
-----END PGP SIGNATURE-----
Merge tag 'mfd-fixes-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull mfd fixes from Lee Jones:
"Couple of simple fixes due for the 3.17 rcs
(and a sneaky document addition that slipped from the previous
pull-request)"
* tag 'mfd-fixes-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd:
mfd: twl4030-power: Fix PM idle pin configuration to not conflict with regulators
mfd: tc3589x: Add device tree bindings
mfd: ab8500-core: Use 'ifdef' for config options
mfd: htc-i2cpld: Fix %d confusingly prefixed with 0x in format string
mfd: omap-usb-host: Fix %d confusingly prefixed with 0x in format string
Commit 43fef47f94 (mfd: twl4030-power: Add a configuration to turn
off oscillator during off-idle) added support for configuring the PMIC
to cut off resources during deeper idle states to save power.
This however caused regression for n900 display power that needed the
PMIC configuration to be disabled with commit d937678ab6 (ARM: dts:
Revert enabling of twl configuration for n900).
Turns out the root cause of the problem is that we must use
TWL4030_RESCONFIG_UNDEF instead of DEV_GRP_NULL to avoid disabling
regulators that may have been enabled before the init function
for twl4030-power.c runs. With TWL4030_RESCONFIG_UNDEF we let the
regulator framework control the regulators like it should. Here we
need to only configure the sys_clken and sys_off_mode triggers for
the regulators that cannot be done by the regulator framework as
it's not running at that point.
This allows us to enable the PMIC configuration for n900.
Fixes: 43fef47f94 (mfd: twl4030-power: Add a configuration to turn off oscillator during off-idle)
Cc: stable@vger.kernel.org # v3.16
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
- Fixes suspend/resume issue on imx53-qsrb due to PMIC IRQ pin
configuration missing
- A couple small SolidRun board fixes/correction from Rabeeh
and Russell
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJT/XBJAAoJEFBXWFqHsHzOuqgH/3XqY4n0kL7lZQGRl8sBA/1m
bLtlKYaGjtn5ITXYONuWyxk9MrkCUaVUEEkcM3Gty6kHbCZ9F8nqSa5NiYs4MyGR
FiBX1GANmz96t61i90jlNNxHdPfnmgj3ZXEDTEj9g2brwGceUgQZv4/D59qSy41H
VlyIIOREQbrIoFlln1cEaKf2UXOpmSpB835QHROwy9K4aK0kZKAR4v5eqM2aQaIl
9VpvR5Xfsmr5vH/srlkY+Vc2ODVF1nQZsa3ikleAh2rzFQ4thwSKqpSxF7HL6EAo
zafJuI67ctyzIFk1PlsUuqCM2NimzACnpgrNG6Vn2KDq/JavNIsuyna0KgzzXqE=
=jOFz
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-3.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
Merge "ARM: imx: fixes for 3.17, 2nd take" from Shawn Guo:
i.MX fixes for 3.17, 2nd take:
- Fixes suspend/resume issue on imx53-qsrb due to PMIC IRQ pin
configuration missing
- A couple small SolidRun board fixes/correction from Rabeeh
and Russell
* tag 'imx-fixes-3.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: microsom-ar8035: MDIO pad must be set open drain
ARM: dts: hummingboard/cubox-i: change SPDIF output to be more descriptive
ARM: dts: hummingboard/cubox-i: add USB OC pinctrl configuration
ARM: dts: imx53-qsrb: Fix suspend/resume
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch is important for the MicroSOM implementation due to the
following details -
1. VIH of the Atheros phy is 1.7V.
2. NVCC_ENET which is the power domain of the MDIO pad is driven by the
PHY's LDO (i.e. either 1.8v or 2.5v).
3. The MicroSOM implements an onbouard 1.6kohm pull up to 3.3v (R3000).
In the case the PHY's LDO was 1.8v then there would be only a 100mV
margin for the signal to be acknowledged as high (1.8v-1.7v).
Due to that setting the pad as an open drain will let the 1.6kohm pull
that signal high to 3.3 that assures enough margins to the PHY to be
acked as '1' logic.
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Similarly to DRA7, OMAP5 has l3 and l4 clock rates incorrectly calculated.
Fixed by using proper divider clock types for the clock nodes.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reported-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For device tree based booting, we need to use wake-up
interrupts like we already do for some omaps. This fixes
a PM regression on beagleboard compared to legacy booting.
Tested-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The kernel has never supported clk32g as a regulator since it is a clock
and not a regulator. Fortunately nothing actually references this node so
we can just remove it.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
GPIO modules are also interrupt sources. However, they require both the
GPIO number and IRQ type to function properly.
By declaring that GPIO uses interrupt-cells=<1>, we essentially do not
allow users of the nodes to use the interrupt property appropritely.
With this change, the following now works:
interrupt-parent = <&gpio6>;
interrupts = <5 IRQ_TYPE_LEVEL_LOW>;
Fixes: 6e58b8f1da ('ARM: dts: DRA7: Add the dts files for dra7 SoC and dra7-evm board')
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For v3.14 and prior, 1-bit Hamming code ECC via software was used
for NAND on this board.
Commit c06c527016 in v3.15 changed the behaviour
to use 1-bit Hamming code via Hardware using a different ECC layout
i.e. (ROM code layout) than what is used by software ECC.
This ECC layout change causes NAND filesystems created in v3.14
and prior to be unusable in v3.15 and later. So revert back to
using software ECC scheme.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Hummingboard has no over current hardware, so disable the over current
detection for both ports.
Cubox-i has over current hardware, so appropriately configure this.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
On r8a7791, i2c6 (aka iic3) doesn't need pinmux, but the koelsch dts
refers to non-existent pinmux configuration data:
pinmux core: sh-pfc does not support function i2c6
sh-pfc e6060000.pfc: invalid function i2c6 in map table
Remove it to fix this.
Fixes: commit 1d41f36a68 ("ARM: shmobile:
koelsch dts: Add VDD MPU regulator for DVFS")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Olof Johansson <olof@lixom.net>
Working on Gigabit/PCIe support in U-Boot for Apalis T30 I realised
that the current device tree source includes for our modules only
happen to work due to referencing the on-carrier 5v0 supply from USB
which is not at all available on-module. The modules actually contain
TPS60150 charge pumps to generate the PMIC required 5 volts from the
one and only 3.3 volt module supply. This patch fixes this.
(Note: When back-porting this to v3.16 stable releases, simply drop the
change to tegra30-apalis.dtsi; that file was added in v3.17)
Cc: <stable@vger.kernel.org> #v3.16+
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
dts files and addition of the new Rockchip list to MAINTAINERS.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCAAGBQJT+hwkAAoJEPOmecmc0R2Bda4IAJ7rxypWxi8RtfxULHu1oGxZ
cdmAsaedAkjTn6tye/99lv1WkLzUD+Q3AxLX6Glu8PgTkocbwtkVTP+gMbv7zwfN
Z9bA6kazPL4Rskr6Am8BFKkGhXHCXChGP1J3z9Gyh07Vu2+3zsvRzyM7hySt3TqZ
EA2dL/uODlukw6EPzFaqGWZLn1OuJmkHXDfnZ3lBI/GFZD9qt5DnYswMBlDlIwr6
D08jmcleRA3wpnY1HXYR2cN1sJmcEP6xVE8ApXd71X0MtumEy49ZTR+4T5/Sh/XN
OPheoH3UUVtXVrAa5fsoUE2xsKs3PZgnIHk1kQklpbw+HArbN+aW0Jh6CySb65Q=
=aNJj
-----END PGP SIGNATURE-----
Merge tag 'v3.17-rockchip-fixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into fixes
Merge "ARM: rockchip: fix for 3.17" from Heiko Stubner:
Pinctrl that got accidentially dropped when reorganizing the
dts files and addition of the new Rockchip list to MAINTAINERS.
* tag 'v3.17-rockchip-fixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
MAINTAINERS: add new Rockchip SoC list
ARM: dts: rockchip: readd missing mmc0 pinctrl settings
Signed-off-by: Olof Johansson <olof@lixom.net>
During the restructuring of the Rockchip Cortex-A9 dtsi files it seems
like the pinctrl settings vanished at some point from the mmc0 support.
This of course renders them unusable, so readd the necessary pinctrl
properties.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Only a single patch in here that fixes a DTC warning.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=PL45
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-3.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into fixes
Merge "Allwinner DT changes, take 2" from Maxime Ripard:
Only a single patch in here that fixes a DTC warning.
* tag 'sunxi-dt-for-3.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
ARM: dt: sun6i: Add #address-cells and #size-cells to i2c controller nodes
Signed-off-by: Olof Johansson <olof@lixom.net>
Increase max i2c bus frequency beyond the default for faster
data transfers. According to the manual, these faster speeds are
only available when the board is wired up the right way. In this case,
the vendor kernel has run at this speed for a long time.
sda-delay is needed for talking to RTC on PMIC, otherwise the i2c
controller never sees an ACK. Strangely the other PMIC i2c slave (the
main one) works fine even without this delay. I Chose value 100 to
match the vendor kernel.
Signed-off-by: Daniel Drake <drake@endlessm.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Tested-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The ODROID kernel shows that the PMIC interrupt line is hooked up
to pin GPX3-2.
This is needed for the max77686-irq driver to create the PMIC IRQ
domain, which is needed by max77686-rtc.
Signed-off-by: Daniel Drake <drake@endlessm.com>
Tested-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The current pinfunc define all uart CTS_B IO port for DCE uart 'CTS_B'
IP port. Since uart IP port 'CTS_B' is output, and it don't need to
set 'SELECT_INPUT' bit.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Previous version had an extra 'fsl' which made the pins not match
any entry. The console message,
vf610-pinctrl 40048000.iomuxc: no fsl,pins property in node \
/soc/aips-bus@40000000/iomuxc@40048000/vf610-twr/esdhc1grp
is displayed without the fix. The prior version would generally
work as u-boot sets the pins properly for sdhc. This change allows
Linux sdhc use even if u-boot is built without sdhc support.
Signed-off-by: Bill Pringlemeir <bpringlemeir@nbsps.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Fixes: 0517fe6aa8 ("ARM: dts: vf610-twr: Add support for sdhc1")
Cc: <stable@vger.kernel.org>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
window:
Group changes to the device tree. In preparation for adding device tree
overlay support, OF_DYNAMIC is reworked so that a set of device tree
changes can be prepared and applied to the tree all at once. OF_RECONFIG
notifiers see the most significant change here so that users always get
a consistent view of the tree. Notifiers generation is moved from before
a change to after it, and notifiers for a group of changes are emitted
after the entire block of changes have been applied
Automatic console selection from DT. Console drivers can now use
of_console_check() to see if the device node is specified as a console
device. If so then it gets added as a preferred console. UART devices
get this support automatically when uart_add_one_port() is called.
DT unit tests no longer depend on pre-loaded data in the device tree.
Data is loaded dynamically at the start of unit tests, and then unloaded
again when the tests have completed.
Also contains a few bugfixes for reserved regions and early memory setup.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8IFz
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux
Pull device tree updates from Grant Likely:
"The branch contains the following device tree changes the v3.17 merge
window:
Group changes to the device tree. In preparation for adding device
tree overlay support, OF_DYNAMIC is reworked so that a set of device
tree changes can be prepared and applied to the tree all at once.
OF_RECONFIG notifiers see the most significant change here so that
users always get a consistent view of the tree. Notifiers generation
is moved from before a change to after it, and notifiers for a group
of changes are emitted after the entire block of changes have been
applied
Automatic console selection from DT. Console drivers can now use
of_console_check() to see if the device node is specified as a console
device. If so then it gets added as a preferred console. UART
devices get this support automatically when uart_add_one_port() is
called.
DT unit tests no longer depend on pre-loaded data in the device tree.
Data is loaded dynamically at the start of unit tests, and then
unloaded again when the tests have completed.
Also contains a few bugfixes for reserved regions and early memory
setup"
* tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux: (21 commits)
of: Fixing OF Selftest build error
drivers: of: add automated assignment of reserved regions to client devices
of: Use proper types for checking memory overflow
of: typo fix in __of_prop_dup()
Adding selftest testdata dynamically into live tree
of: Add todo tasklist for Devicetree
of: Transactional DT support.
of: Reorder device tree changes and notifiers
of: Move dynamic node fixups out of powerpc and into common code
of: Make sure attached nodes don't carry along extra children
of: Make devicetree sysfs update functions consistent.
of: Create unlocked versions of node and property add/remove functions
OF: Utility helper functions for dynamic nodes
of: Move CONFIG_OF_DYNAMIC code into a separate file
of: rename of_aliases_mutex to just of_mutex
of/platform: Fix of_platform_device_destroy iteration of devices
of: Migrate of_find_node_by_name() users to for_each_node_by_name()
tty: Update hypervisor tty drivers to use core stdout parsing code.
arm/versatile: Add the uart as the stdout device.
of: Enable console on serial ports specified by /chosen/stdout-path
...
