These drivers use 9100-byte receive buffers, thus allocating an skb requires
an O(3) memory allocation. Under heavy memory loads and fragmentation, such
a request can fail. Previous versions of the driver have dropped the packet
and reused the old buffer; however, the new version introduced a bug in that
it released the old buffer before trying to allocate a new one. The previous
method is implemented here. The skb is unmapped before any attempt is made to
allocate another.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [v3.18]
Reported-by: Eric Biggers <ebiggers3@gmail.com>
Cc: Eric Biggers <ebiggers3@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The CPSW IP implements pulse-signaled interrupts. Due to
that we must write a correct, pre-defined value to the
CPDMA_MACEOIVECTOR register so the controller generates
a pulse on the correct IRQ line to signal the End Of
Interrupt.
The way the driver is written today, all four IRQ lines
are requested using the same IRQ handler and, because of
that, we could fall into situations where a TX IRQ fires
but we tell the controller that we ended an RX IRQ (or
vice-versa). This situation triggers an IRQ storm on the
reserved IRQ 127 of INTC which will in turn call ack_bad_irq()
which will, then, print a ton of:
unexpected IRQ trap at vector 00
In order to fix the problem, we are moving all calls to
cpdma_ctlr_eoi() inside the IRQ handler and making sure
we *always* write the correct value to the CPDMA_MACEOIVECTOR
register. Note that the algorithm assumes that IRQ numbers and
value-to-be-written-to-EOI are proportional, meaning that a
write of value 0 would trigger an EOI pulse for the RX_THRESHOLD
Interrupt and that's the IRQ number sitting in the 0-th index
of our irqs_table array.
This, however, is safe at least for current implementations of
CPSW so we will refrain from making the check smarter (and, as
a side-effect, slower) until we actually have a platform where
IRQ lines are swapped.
This patch has been tested for several days with AM335x- and
AM437x-based platforms. AM57x was left out because there are
still pending patches to enable ethernet in mainline for that
platform. A read of the TRM confirms the statement on previous
paragraph.
Reported-by: Yegor Yefremov <yegorslists@googlemail.com>
Fixes: 510a1e7 (drivers: net: davinci_cpdma: acknowledge interrupt properly)
Cc: <stable@vger.kernel.org> # v3.9+
Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When allocation of all RQs fail, we do not free previously allocated buffers,
before returning error. This causes memory leak.
This patch fixes this by calling vnic_rq_clean(), which frees all the rq
buffers.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some buggy firmwares export an incorrect MAC address (00:a0:c6:00:00:00). This
makes for example checking devices for random MAC addresses tricky, and you
might end up with multiple network interfaces with the same address.
This patch tries to fix, or at least improve, the situation by setting the MAC
address of devices with this firmware bug to a random address. I tested the
patch with two devices that has this firmware bug (Huawei E398 and E392), and
network traffic worked fine after changing the address.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now, when VLAN acceleration was in use, the bytes of the VLAN header
were not included in port or flow byte counters. They were however
included when VLAN acceleration was not used. This commit corrects the
inconsistency, by always including the VLAN header in byte counters.
Previous discussion at
http://openvswitch.org/pipermail/dev/2014-December/049521.html
Reported-by: Motonori Shindo <mshindo@vmware.com>
Signed-off-by: Ben Pfaff <blp@nicira.com>
Reviewed-by: Flavio Leitner <fbl@sysclose.org>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Jarosch reported IPsec TCP stalls when a PMTU event occurs.
In fact the problem was completely unrelated to IPsec. The bug is
also reproducible if you just disable TSO/GSO.
The problem is that when the MSS goes down, existing queued packet
on the TX queue that have not been transmitted yet all look like
TSO packets and get treated as such.
This then triggers a bug where tcp_mss_split_point tells us to
generate a zero-sized packet on the TX queue. Once that happens
we're screwed because the zero-sized packet can never be removed
by ACKs.
Fixes: 1485348d24 ("tcp: Apply device TSO segment limit earlier")
Reported-by: Thomas Jarosch <thomas.jarosch@intra2net.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Cheers,
Signed-off-by: David S. Miller <davem@davemloft.net>
Altera network device doesn't come up after
ifconfig eth0 down
ifconfig eth0 up
The reason behind is clearing priv->phydev during tse_shutdown().
The phydev is not restored back at tse_open().
Resubmiting as to follow Tobias Klauser suggestion.
phy_start/phy_stop are called on each ifup/ifdown and
phy_disconnect is called once during the module removal.
Signed-off-by: Kostya Belezko <bkostya@hotmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz says:
====================
mlx4 driver fixes for 3.19-rc2
Please push Maor's patch to -stable >= 3.17
Jack's fixes error-flow issues introduced in 3.19-rc1, no need for -stable.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We shouldn't call UNMAP_FA here, this is done in mlx4_load_one.
If mlx4_query_func fails, we need to invoke CLOSE_HCA for both
native and master.
Fixes: a0eacca948 ('net/mlx4_core: Refactor mlx4_load_one')
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, mlx4_mt_rereg_write filled the MPT's entity_size with the
old MTT's page shift, which could result in using an incorrect offset.
Fix the initialization to be after we calculate the new MTT offset.
In addition, assign mtt order to -1 after calling mlx4_mtt_cleanup. This
is necessary in order to mark the MTT as invalid and avoid freeing it later.
Fixes: e630664 ('mlx4_core: Add helper functions to support MR re-registration')
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the check of adapter fails and goes into the 'else' branch, the
return value 'err' should not still be zero.
Signed-off-by: Yongjian Xu <xuyongjiande@gmail.com>
Acked-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return a negative error code on failure.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret; expression e1,e2;
@@
(
if (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return a negative error code on failure.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret; expression e1,e2;
@@
(
if (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return a negative error code on failure.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret; expression e1,e2;
@@
(
if (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
The patch also modifies the test of mgp->cmd to satisfy checkpatch.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return a negative error code on failure.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret; expression e1,e2;
@@
(
if (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2014-12-31
This series contains updates to fixes for e100, igb and i40e.
John Linville fixes a typo in e100 that has been around for some time,
where an attempted revert actually inverted the test for eeprom_mdix_enabled.
Todd fixes up a code comment that should have been removed back in 2007.
Joe Perches fixes a possible memory leak in i40e which was reported by
Dan Carpenter using smatch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
I didn't notice that return in the code, fix it by
adding a goto out instead to free the memory.
Fixes:
> New smatch warnings:
> drivers/net/ethernet/intel/i40e/i40e_debugfs.c:832 i40e_dbg_dump_desc() warn: possible memory leak of 'ring'
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove a FIXME comment that was missed in a commit on 1/2007.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Reported-by: nick <xerofoify@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Although it doesn't explicitly say so, commit 60ffa47875 ("e100:
Fix MDIO/MDIO-X") appears to be intended to revert the earlier commit
648951451e ("e100: fixed e100 MDI/MDI-X issues"). However,
careful examination reveals that the attempted revert actually
_inverted_ the test for eeprom_mdix_enabled. That is bound to program
a few PHYs incorrectly...
https://bugzilla.redhat.com/show_bug.cgi?id=1156417
Signed-off-by: "John W. Linville" <linville@tuxdriver.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Pull networking fixes from David Miller:
1) Fix double SKB free in bluetooth 6lowpan layer, from Jukka Rissanen.
2) Fix receive checksum handling in enic driver, from Govindarajulu
Varadarajan.
3) Fix NAPI poll list corruption in virtio_net and caif_virtio, from
Herbert Xu. Also, add code to detect drivers that have this mistake
in the future.
4) Fix doorbell endianness handling in mlx4 driver, from Amir Vadai.
5) Don't clobber IP6CB() before xfrm6_policy_check() is called in TCP
input path,f rom Nicolas Dichtel.
6) Fix MPLS action validation in openvswitch, from Pravin B Shelar.
7) Fix double SKB free in vxlan driver, also from Pravin.
8) When we scrub a packet, which happens when we are switching the
context of the packet (namespace, etc.), we should reset the
secmark. From Thomas Graf.
9) ->ndo_gso_check() needs to do more than return true/false, it also
has to allow the driver to clear netdev feature bits in order for
the caller to be able to proceed properly. From Jesse Gross.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (62 commits)
genetlink: A genl_bind() to an out-of-range multicast group should not WARN().
netlink/genetlink: pass network namespace to bind/unbind
ne2k-pci: Add pci_disable_device in error handling
bonding: change error message to debug message in __bond_release_one()
genetlink: pass multicast bind/unbind to families
netlink: call unbind when releasing socket
netlink: update listeners directly when removing socket
genetlink: pass only network namespace to genl_has_listeners()
netlink: rename netlink_unbind() to netlink_undo_bind()
net: Generalize ndo_gso_check to ndo_features_check
net: incorrect use of init_completion fixup
neigh: remove next ptr from struct neigh_table
net: xilinx: Remove unnecessary temac_property in the driver
net: phy: micrel: use generic config_init for KSZ8021/KSZ8031
net/core: Handle csum for CHECKSUM_COMPLETE VXLAN forwarding
openvswitch: fix odd_ptr_err.cocci warnings
Bluetooth: Fix accepting connections when not using mgmt
Bluetooth: Fix controller configuration with HCI_QUIRK_INVALID_BDADDR
brcmfmac: Do not crash if platform data is not populated
ipw2200: select CFG80211_WEXT
...
Pull CIFS fixes from Steve French:
"A set of three minor cifs fixes"
* 'for-linus' of git://git.samba.org/sfrench/cifs-2.6:
cifs: make new inode cache when file type is different
Fix signed/unsigned pointer warning
Convert MessageID in smb2_hdr to LE
Pull UDF & isofs fixes from Jan Kara:
"A couple of UDF fixes of handling of corrupted media and one iso9660
fix of the same"
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
udf: Reduce repeated dereferences
udf: Check component length before reading it
udf: Check path length when reading symlink
udf: Verify symlink size before loading it
udf: Verify i_size when loading inode
isofs: Fix unchecked printing of ER records
- Fix for a potential NULL pointer dereference in the cpufreq
core due to an initialization race condition (Ethan Zhao).
- Fixes for abuse of the OPP (Operating Performance Points) API
related to RCU and other minor issues in the OPP library and
the cpufreq-dt driver (Dmitry Torokhov).
- cpuidle governors cleanup making them measure idle duration in
a better way without using the CPUIDLE_FLAG_TIME_INVALID flag
which allows that flag to be dropped from the ACPI cpuidle driver
and from the core too (Len Brown).
- New ACPI backlight blacklist entries for Samsung machines
without a working native backlight interface that need to
use the ACPI backlight instead (Aaron Lu).
- New CPU IDs of future Intel Xeon CPUs for the Intel RAPL power
capping driver (Jacob Pan).
- Generic power domains framework modification to export the
of_genpd_get_from_provider() function to modular drivers that
will allow future driver modifications to be based on the mainline
(Amit Daniel Kachhap).
- Two fixes for the cpupower tool (Michal Privoznik, Prarit Bhargava).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=CYBE
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.19-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI material from Rafael J Wysocki:
"These are fixes (operating performance points library, cpufreq-dt
driver, cpufreq core, ACPI backlight, cpupower tool), cleanups
(cpuidle), new processor IDs for the RAPL (Running Average Power
Limit) power capping driver, and a modification of the generic power
domains framework allowing modular drivers to call one of its helper
functions.
Specifics:
- Fix for a potential NULL pointer dereference in the cpufreq core
due to an initialization race condition (Ethan Zhao).
- Fixes for abuse of the OPP (Operating Performance Points) API
related to RCU and other minor issues in the OPP library and the
cpufreq-dt driver (Dmitry Torokhov).
- cpuidle governors cleanup making them measure idle duration in a
better way without using the CPUIDLE_FLAG_TIME_INVALID flag which
allows that flag to be dropped from the ACPI cpuidle driver and
from the core too (Len Brown).
- New ACPI backlight blacklist entries for Samsung machines without a
working native backlight interface that need to use the ACPI
backlight instead (Aaron Lu).
- New CPU IDs of future Intel Xeon CPUs for the Intel RAPL power
capping driver (Jacob Pan).
- Generic power domains framework modification to export the
of_genpd_get_from_provider() function to modular drivers that will
allow future driver modifications to be based on the mainline (Amit
Daniel Kachhap).
- Two fixes for the cpupower tool (Michal Privoznik, Prarit
Bhargava)"
* tag 'pm+acpi-3.19-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / video: Add some Samsung models to disable_native_backlight list
tools / cpupower: Fix no idle state information return value
tools / cpupower: Correctly detect if running as root
cpufreq: fix a NULL pointer dereference in __cpufreq_governor()
cpufreq-dt: defer probing if OPP table is not ready
PM / OPP: take RCU lock in dev_pm_opp_get_opp_count
PM / OPP: fix warning in of_free_opp_table()
PM / OPP: add some lockdep annotations
powercap / RAPL: add IDs for future Xeon CPUs
PM / Domains: Export of_genpd_get_from_provider function
cpuidle / ACPI: remove unused CPUIDLE_FLAG_TIME_INVALID
cpuidle: ladder: Better idle duration measurement without using CPUIDLE_FLAG_TIME_INVALID
cpuidle: menu: Better idle duration measurement without using CPUIDLE_FLAG_TIME_INVALID
Users can request to bind to arbitrary multicast groups, so warning
when the requested group number is out of range is not appropriate.
And with the warning removed, and the 'err' variable properly given
an initial value, we can remove 'found' altogether.
Reported-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A few driver specific fixes here, the DMA burst size increase in the
spfi driver is a fix to make the hardware happier in some situations.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUoX+AAAoJECTWi3JdVIfQnCUH+wezEX6JeLIW86WiCjHB5hE2
oEhkp7MS/0qSasgguEQ/kDaov1p8hn3nnpY6t5H695L/MWN8sALBkOymbOhUyNGB
hWOxpIJ31vdy4hauo/GvEQe9nsR8/AHeM3+e85qQWQKrUZgkDsmZckDy19WlFbdN
sUuqmfzyAB2xImTmtkAhe2nia3XOoHsvwfZcKXQEyEl4HOQkazD/iC4JNOkP9l98
NA3U9bFvL1PLD9r0E3A3Ly0LHW90f+DB+Ssuxxdh1CcCTLSxQc0VMnBbCslM0A13
aiwINf+wFDnh/kx4aAlbmVnOq4JECOwURWmfxqldNmvbc8zuDx8xLdUhQ40CPlk=
=xJxL
-----END PGP SIGNATURE-----
Merge tag 'spi-v3.19-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A few driver specific fixes here, the DMA burst size increase in the
spfi driver is a fix to make the hardware happier in some situations"
* tag 'spi-v3.19-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: img-spfi: Increase DMA burst size
spi: img-spfi: Enable controller before starting TX DMA
spi: sh-msiof: Add runtime PM lock in initializing
One fix here, a fix for the voltage mapping on one of the s2mps11
regulators which broke systems using it including apparently the Gear 2
smartwatches.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUoX7vAAoJECTWi3JdVIfQtcEH/junzpSCOwIrI8NG9/ZF0xt5
rLB1SlDxtiSPv6eFA+KXYYmO8VNjZ1g+NN1PoeSNgAK08YzG9IUHIqI1L1iDe2qG
2vpPY++Rg5eWPY79Sa9oy/+2zmFmUh3t+Shv7p3WC1Q8GES4bD6dm/QVxykh16nW
nDGYZN981THIHS9xPKsmvCbHMp6PknDZkqO9Umzflt7cYgzgFP8xTaTlb4vkwTza
3ZjGnEMIe1ldkLGFEJmdsSMro07hKzVYk8e3auOK+gAMpO+QjpY8WxuarmpQBPLx
GddKhfkox5HNUxm9jRp0jivgi8YXD4a1lXzwXpxSihax1Q/Q/v00yoJ6selRQXg=
=/mpj
-----END PGP SIGNATURE-----
Merge tag 'regulator-v3.19-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull one regulator fix from Mark Brown:
"One fix here, a fix for the voltage mapping on one of the s2mps11
regulators which broke systems using it including apparently the
Gear 2 smartwatches"
* tag 'regulator-v3.19-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: s2mps11: Fix dw_mmc failure on Gear 2
- Fix selection of buswidth for mmc hosts supporting 1-bit only.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ncvX
-----END PGP SIGNATURE-----
Merge tag 'mmc-v3.19-2' of git://git.linaro.org/people/ulf.hansson/mmc
Pull one MMC fix from Ulf Hansson:
"MMC core:
- Fix selection of buswidth for mmc hosts supporting 1-bit only"
* tag 'mmc-v3.19-2' of git://git.linaro.org/people/ulf.hansson/mmc:
mmc: core: stop trying to switch width when only one bit is supported
Pull thermal management updates from Zhang Rui:
"First of all, the most important change is the thermal cpu cooling
fixes. The major fix here is to have proper sequencing between
cpufreq layer and thermal cpu cooling registration. A take away of
this fix is an improvement in the thermal drivers code. Thermal
drivers that require cpu cooling do not need to check for cpufreq
layer. The requirement now is to propagate the error code, if any,
while registering cpu cooling device. Thanks to Viresh for
implementing the required CPUfreq changes.
Second, a new driver is introduced for int340x processor thermal
device. Given that int340x thermal is disabled by default, and this
processor thermal device is only available on limited platforms, plus
the driver does nothing but exposes some thermal limitation
information for user space to use, thus I think it is safe to include
it in this pull request after missing 3.19-rc2.
Specifics:
- Thermal cpu cooling fixes and cleanups.
- introduce INT340X processor thermal reporting device driver.
- several small fixes and cleanups for int340x thermal drivers"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (43 commits)
Thermal/int340x/int3403: Free acpi notification handler
Thermal/int340x/processor_thermal: Fix memory leak
Thermal/int340x/int3403: Fix memory leak
thermal: int340x: Introduce processor reporting device
thermal: int340x_thermal: drop owner assignment from platform_drivers
thermal: drop owner assignment from platform_drivers
thermal: cpu_cooling: document node in struct cpufreq_cooling_device
thermal/powerclamp: add ids for future xeon cpus
Thermal/int340x: Handle properly the case when _trt or _art acpi entry is missing
thermal: cpu_cooling: return ERR_PTR() for !CPU_THERMAL or !THERMAL_OF
thermal: cpu_cooling: small memory leak on error
thermal: ti-soc-thermal: Do not print error message in the EPROBE_DEFER case
thermal: db8500: Do not print error message in the EPROBE_DEFER case
thermal: imx: Do not print error message in the EPROBE_DEFER case
thermal: Fix cdev registration with THERMAL_NO_LIMIT on 64bit
drivers: thermal: Remove ARCH_HAS_BANDGAP dependency for samsung
thermal:core:fix: Check return code of the ->get_max_state() callback
thermal: cpu_cooling: update copyright tags
thermal: cpu_cooling: Use cpufreq_dev->freq_table for finding level/freq
thermal: cpu_cooling: Store frequencies in descending order
...
Commit 2457aec637 ("mm: non-atomically mark page accessed during page
cache allocation where possible") has added a separate parameter for
specifying gfp mask for radix tree allocations.
Not only this is less than optimal from the API point of view because it
is error prone, it is also buggy currently because
grab_cache_page_write_begin is using GFP_KERNEL for radix tree and if
fgp_flags doesn't contain FGP_NOFS (mostly controlled by fs by
AOP_FLAG_NOFS flag) but the mapping_gfp_mask has __GFP_FS cleared then
the radix tree allocation wouldn't obey the restriction and might
recurse into filesystem and cause deadlocks. This is the case for most
filesystems unfortunately because only ext4 and gfs2 are using
AOP_FLAG_NOFS.
Let's simply remove radix_gfp_mask parameter because the allocation
context is same for both page cache and for the radix tree. Just make
sure that the radix tree gets only the sane subset of the mask (e.g. do
not pass __GFP_WRITE).
Long term it is more preferable to convert remaining users of
AOP_FLAG_NOFS to use mapping_gfp_mask instead and simplify this
interface even further.
Reported-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* pm-domains:
PM / Domains: Export of_genpd_get_from_provider function
* powercap:
powercap / RAPL: add IDs for future Xeon CPUs
* pm-tools:
tools / cpupower: Fix no idle state information return value
tools / cpupower: Correctly detect if running as root
* pm-cpufreq:
cpufreq: fix a NULL pointer dereference in __cpufreq_governor()
cpufreq-dt: defer probing if OPP table is not ready
* pm-cpuidle:
cpuidle / ACPI: remove unused CPUIDLE_FLAG_TIME_INVALID
cpuidle: ladder: Better idle duration measurement without using CPUIDLE_FLAG_TIME_INVALID
cpuidle: menu: Better idle duration measurement without using CPUIDLE_FLAG_TIME_INVALID
mmc_select_bus_width() will try to switch to MMC_BUS_WIDTH_4 even if
MMC_CAP_4_BIT_DATA and MMC_CAP_8_BIT_DATA are not set in host->caps.
Return as soon as possible when those flags are not set
Fixes: 577fb13199 (mmc: rework selection of bus speed mode)
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: <stable@vger.kernel.org> # 3.17
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On top of this, add a couple of WARN_ONs and stop spamming dmesg on
pretty much every boot of a virtual machine.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJUn8hXAAoJEL/70l94x66Dme4H/R/HA+Aswgzse8nx3pNiqStv
e0BBeUHVJtxlOfnOlJGCWc1ef7uzKdvVWuqCmJwMDJDoLd/I8kF84E3AQS+zTJ/u
Dlb+yjwjoFPbQwr8xfclcvYXZxJgleKQJcyBWKBxgMTnFdjgRfX7U0MzXZJ/gFzH
mdHhLlNBU/On0l3A+dsKVgjtiuHZIQD0FraYs4qa2QajRGgDoHypzTmwh20XBmdx
3l/zFnSFSbaCTckbKb0xYv22pZTMd/5qrxer05sl98nzrrrXIDhVSo0hbrNVqorv
pDr+908XGvTOgVR1cvgkFn74INudiYjNyICGsue/ksmUPh9jz6hWic7sNeqYfcI=
=ehkB
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"The important fixes are for two bugs introduced by the merge window.
On top of this, add a couple of WARN_ONs and stop spamming dmesg on
pretty much every boot of a virtual machine"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
kvm: warn on more invariant breakage
kvm: fix sorting of memslots with base_gfn == 0
kvm: x86: drop severity of "generation wraparound" message
kvm: x86: vmx: reorder some msr writing
Pull vfs fix from Al Viro:
"An embarrassing bug in lustre patches from this cycle ;-/"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
[regression] braino in "lustre: use is_root_inode()"
Modifying a non-existent slot is not allowed. Also check that the
first loop doesn't move a deleted slot beyond the used part of
the mslots array.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Before commit 0e60b0799f (kvm: change memslot sorting rule from size
to GFN, 2014-12-01), the memslots' sorting key was npages, meaning
that a valid memslot couldn't have its sorting key equal to zero.
On the other hand, a valid memslot can have base_gfn == 0, and invalid
memslots are identified by base_gfn == npages == 0.
Because of this, commit 0e60b0799f broke the invariant that invalid
memslots are at the end of the mslots array. When a memslot with
base_gfn == 0 was created, any invalid memslot before it were left
in place.
This can be fixed by changing the insertion to use a ">=" comparison
instead of "<=", but some care is needed to avoid breaking the case
of deleting a memslot; see the comment in update_memslots.
Thanks to Tiejun Chen for posting an initial patch for this bug.
Reported-by: Jamie Heilman <jamie@audible.transient.net>
Reported-by: Andy Lutomirski <luto@amacapital.net>
Tested-by: Jamie Heilman <jamie@audible.transient.net>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Just a couple of fixes for the new Intel Skylake HD-audio support.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=EYsC
-----END PGP SIGNATURE-----
Merge tag 'sound-3.19-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Just a couple of fixes for the new Intel Skylake HD-audio support"
* tag 'sound-3.19-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda_intel: apply the Seperate stream_tag for Skylake
ALSA: hda_controller: Separate stream_tag for input and output streams.
Since most virtual machines raise this message once, it is a bit annoying.
Make it KERN_DEBUG severity.
Cc: stable@vger.kernel.org
Fixes: 7a2e8aaf0f
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The commit 34a1cd60d1, "x86: vmx: move some vmx setting from
vmx_init() to hardware_setup()", tried to refactor some codes
specific to vmx hardware setting into hardware_setup(), but some
msr writing should depend on our previous setting condition like
enable_apicv, enable_ept and so on.
Reported-by: Jamie Heilman <jamie@audible.transient.net>
Tested-by: Jamie Heilman <jamie@audible.transient.net>
Signed-off-by: Tiejun Chen <tiejun.chen@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Netlink families can exist in multiple namespaces, and for the most
part multicast subscriptions are per network namespace. Thus it only
makes sense to have bind/unbind notifications per network namespace.
To achieve this, pass the network namespace of a given client socket
to the bind/unbind functions.
Also do this in generic netlink, and there also make sure that any
bind for multicast groups that only exist in init_net is rejected.
This isn't really a problem if it is accepted since a client in a
different namespace will never receive any notifications from such
a group, but it can confuse the family if not rejected (it's also
possible to silently (without telling the family) accept it, but it
would also have to be ignored on unbind so families that take any
kind of action on bind/unbind won't do unnecessary work for invalid
clients like that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For linux-3.18.0
The driver lacks pci_disable_device in error handling code of
ne2k_pci_init_one, so the device enabled by pci_enable_device is not
disabled when errors occur.
This patch fixes this problem.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In __bond_release_one(), when the interface is not a slave or not a slave of
"this" master, it log error message.
The message actually should be a debug message matching what bond_enslave()
does.
Signed-off-by: Wengang Wang <wen.gang.wang@oracle.com>
Acked-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg says:
====================
netlink/genetlink cleanups & multicast improvements
I'm looking at using the multicast group functionality in a way that would
benefit from knowing when there are subscribers to avoid collecting the
required data when there aren't any. During this I noticed that the unbind
for multicast groups doesn't actually work - it's never called when sockets
are closed. Luckily, nobody actually uses the functionality.
While looking at the code trying to find why it's not called and where the
multicast listeners are actually removed, I found the potential cleanup in
patch 3. Patch 2 also has a cleanup for a generic netlink API in this area.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to make the newly fixed multicast bind/unbind
functionality in generic netlink, pass them down to the
appropriate family.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, netlink_unbind() is only called when the socket
explicitly unbinds, which limits its usefulness (luckily
there are no users of it yet anyway.)
Call netlink_unbind() also when a socket is released, so it
becomes possible to track listeners with this callback and
without also implementing a netlink notifier (and checking
netlink_has_listeners() in there.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code is now confusing to read - first in one function down
(netlink_remove) any group subscriptions are implicitly removed
by calling __sk_del_bind_node(), but the subscriber database is
only updated far later by calling netlink_update_listeners().
Move the latter call to just after removal from the list so it
is easier to follow the code.
This also enables moving the locking inside the kernel-socket
conditional, which improves the normal socket destruction path.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
