- Shorten include paths to machine dependent headers.
- Add support for fifth serial port.
- Remove CONFIG_ETRAXFS_SIM and CONFIG_ETRAX_DEBUG_PORT_NULL, no longer used.
- Remove raw_printk and stupid_debug hack, no longer needed.
- Remove dummy console stuff, no longer needed.
- Correct some register type names.
- Correct some whitespace errors and formatting.
- Add ifdef for ETRAX_AXISFLASHMAP to avoid compiling file unless it is set.
- Use assembler macros for setting up clocks.
- Don't copy image, just jump to it (only works for NOR flash)
- Shorten include paths to machine specific headers.
- Remove fill_inbuf, not defined here.
- Return __dest as value from memcpy.
- Enable serial port hardware transmitter and receiver in serial_setup.
- Correct baudrate divisor calculation, changed from 4800 to 115200.
- Add support for Artpec-3 specific serial port setup.
- Initialize pinmux for the correct serial port.
- Fixes for NAND and NOR flash booting.
- Use assembler macros for common tasks (clocks, general io etc)
- Use (EtraxFS or Artpec-3) machine specific include for dram and hardware init.
- Remove old specific targets, use more generic ones instead.
- Use if_changed to avoid creating new images when no change.
- Use EXTRA_CFLAGS instead of CFLAGS.
- Remove old specific targets, use more generic ones instead.
- Use if_changed to avoid creating new images when no change.
- Use KBUILD_CFLAGS instead of CFLAGS.
- Remove raw_prink hack, use oops_in_progress instead.
- When ETRAX_WATCHDOG_NICE_DOGGY is set, loop in trap after oops dump
instead of rebooting.
- Break long lines to less than 80 chars.
- Fix whitespace errors.
- Remove unnecessary comments.
- Add config to use mtd0 as whole flash device.
- Fix whitespace errors.
- Remove braces around single statement ifs.
- Break long lines.
- Remove unnecessary CVS log.
- Remove old specific targets, use more generic ones instead.
- Use if_changed to avoid creating new images when no change.
Removes a lot of cruft.
- Use EXTRA_CFLAGS instead of CFLAGS.
- Remove old specific targets, use more generic ones instead.
- Use if_changed to avoid creating new images when no change.
- Use EXTRA_CFLAGS instead of CFLAGS.
- Remove old and non-generic targets, use generic ones instead.
- Add sub-arch as mach-fs or mach-a3 for EtraxFS and Artpec-3 respectively.
- Add links to sub-arch directories, and erase before trying to create them.
- Include from sub-arch specific include directory "mach".
- Add files to be cleaned in CLEAN_FILES instead of as archclean target.
- Use default partition table when no partition is found (for initial tests)
- Add config ETRAX_AXISFLASHMAP_MTD0WHOLE to allow whole flash as mtd0.
- Add config for VCS simulator connection.
- Add i2c_write and i2c_read as functions.
- Use spinlocks for critical regions.
- Add config item to set I2C data and clock port.
- Put unneeded testcode inside #if 0.
- Remove CVS id tag.
- Remove CRISv32 common arbiter, dma, io and pinmux files,
they are now defined in machine dependent directories.
- Add cache and cacheflush files for working around cache problems
in CRISv32 chips.
- Collect extern declarations at top of file.
- Change raw_printk to printk, use oops_in_progress instead.
- Fix formatting and whitespace.
- Allow the watchdog to be disabled during oops.
- Only disallow oops if we're in_interrupt context (was in_atomic before)
- Use the generic oops_in_progress instead of the raw_printk hack.
- Fix whitespace/formatting.
- Remove CVS log entries.
- Add partition table struct to be used to parse partition table in flash.
- Add JFFS2 as a type, and add readoly flag.
- Improve some comments.
- Lindent has been run, fixing whitespace and formatting issues.
The header files describe the hardware registers available in both
these chips, note that most of this documentation is automatically
generated from the hardware implementation.
The two chips are somewhat different, and needs different handling.
Adds handing of the dma, dram initialization, hardware settings, io,
memory arbiter and pinmux
Also moves the dma, dram initialization and io from CRIS v32 common files.
- Remove some unneeded configs and add some new ones.
- Merge common config items to common file instead of duplicating them.
- Pull in standard Kconfig.preempt.
- Remove some unneeded Kconfigs for subsystems not (yet) available on CRIS
(md, scsi, ieee1394, i2o, isdn, telephony, media, pcmcia, pci)
- Rename CRISv32 config items which had different types from CRISv10.
(ETRAX_LED2G, ETRAX_LED2R, ETRAX_LED3G, ETRAX_LED3R, ETRAX_I2C_DATA_PORT,
ETRAX_I2C_CLK_PORT)
* 'for-linus' of git://oss.sgi.com:8090/xfs/xfs-2.6: (62 commits)
[XFS] add __init/__exit mark to specific init/cleanup functions
[XFS] Fix oops in xfs_file_readdir()
[XFS] kill xfs_root
[XFS] keep i_nlink updated and use proper accessors
[XFS] stop updating inode->i_blocks
[XFS] Make xfs_ail_check check less by default
[XFS] Move AIL pushing into it's own thread
[XFS] use generic_permission
[XFS] stop re-checking permissions in xfs_swapext
[XFS] clean up xfs_swapext
[XFS] remove permission check from xfs_change_file_space
[XFS] prevent panic during log recovery due to bogus op_hdr length
[XFS] Cleanup various fid related bits:
[XFS] Fix xfs_lowbit64
[XFS] Remove CFORK macros and use code directly in IFORK and DFORK macros.
[XFS] kill superflous buffer locking (2nd attempt)
[XFS] Use kernel-supplied "roundup_pow_of_two" for simplicity
[XFS] Remove the BPCSHIFT and NB* based macros from XFS.
[XFS] Remove bogus assert
[XFS] optimize XFS_IS_REALTIME_INODE w/o realtime config
...
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Douglas Gilbert <dougg@torque.net>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'slub-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/christoph/vm:
SLUB: fix checkpatch warnings
Use non atomic unlock
SLUB: Support for performance statistics
SLUB: Alternate fast paths using cmpxchg_local
SLUB: Use unique end pointer for each slab page.
SLUB: Deal with annoying gcc warning on kfree()
This patch adds extra information to the mirror status output, so that
it can be determined which device(s) have failed. For each mirror device,
a character is printed indicating the most severe error encountered. The
characters are:
* A => Alive - No failures
* D => Dead - A write failure occurred leaving mirror out-of-sync
* S => Sync - A sychronization failure occurred, mirror out-of-sync
* R => Read - A read failure occurred, mirror data unaffected
This allows userspace to properly reconfigure the mirror set.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch gives the ability to respond-to/record device failures
that happen during read operations. It also adds the ability to
read from mirror devices that are not the primary if they are
in-sync.
There are essentially two read paths in mirroring; the direct path
and the queued path. When a read request is mapped, if the region
is 'in-sync' the direct path is taken; otherwise the queued path
is taken.
If the direct path is taken, we must record bio information so that
if the read fails we can retry it. We then discover the status of
a direct read through mirror_end_io. If the read has failed, we will
mark the device from which the read was attempted as failed (so we
don't try to read from it again), restore the bio and try again.
If the queued path is taken, we discover the results of the read
from 'read_callback'. If the device failed, we will mark the device
as failed and attempt the read again if there is another device
where this region is known to be 'in-sync'.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch adds the ability to requeue write I/O to
core device-mapper when there is a log device failure.
If a write to the log produces and error, the pending writes are
put on the "failures" list. Since the log is marked as failed,
they will stay on the failures list until a suspend happens.
Suspends come in two phases, presuspend and postsuspend. We must
make sure that all the writes on the failures list are requeued
in the presuspend phase (a requirement of dm core). This means
that recovery must be complete (because writes may be delayed
behind it) and the failures list must be requeued before we
return from presuspend.
The mechanisms to ensure recovery is complete (or stopped) was
already in place, but needed to be moved from postsuspend to
presuspend. We rely on 'flush_workqueue' to ensure that the
mirror thread is complete and therefore, has requeued all writes
in the failures list.
Because we are using flush_workqueue, we must ensure that no
additional 'queue_work' calls will produce additional I/O
that we need to requeue (because once we return from
presuspend, we are unable to do anything about it). 'queue_work'
is called in response to the following functions:
- complete_resync_work = NA, recovery is stopped
- rh_dec (mirror_end_io) = NA, only calls 'queue_work' if it
is ready to recover the region
(recovery is stopped) or it needs
to clear the region in the log*
**this doesn't get called while
suspending**
- rh_recovery_end = NA, recovery is stopped
- rh_recovery_start = NA, recovery is stopped
- write_callback = 1) Writes w/o failures simply call
bio_endio -> mirror_end_io -> rh_dec
(see rh_dec above)
2) Writes with failures are put on
the failures list and queue_work is
called**
** write_callbacks don't happen
during suspend **
- do_failures = NA, 'queue_work' not called if suspending
- add_mirror (initialization) = NA, only done on mirror creation
- queue_bio = NA, 1) delayed I/O scheduled before flush_workqueue
is called. 2) No more I/Os are being issued.
3) Re-attempted READs can still be handled.
(Write completions are handled through rh_dec/
write_callback - mention above - and do not
use queue_bio.)
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch adds the calls to 'fail_mirror' if an error occurs during
mirror recovery (aka resynchronization). 'fail_mirror' is responsible
for recording the type of error by mirror device and ensuring an event
gets raised for the purpose of notifying userspace.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch gives mirror the ability to handle device failures
during normal write operations.
The 'write_callback' function is called when a write completes.
If all the writes failed or succeeded, we report failure or
success respectively. If some of the writes failed, we call
fail_mirror; which increments the error count for the device, notes
the type of error encountered (DM_RAID1_WRITE_ERROR), and
selects a new primary (if necessary). Note that the primary
device can never change while the mirror is not in-sync (IOW,
while recovery is happening.) This means that the scenario
where a failed write changes the primary and gives
recovery_complete a chance to misread the primary never happens.
The fact that the primary can change has necessitated the change
to the default_mirror field. We need to protect against reading
garbage while the primary changes. We then add the bio to a new
list in the mirror set, 'failures'. For every bio in the 'failures'
list, we call a new function, '__bio_mark_nosync', where we mark
the region 'not-in-sync' in the log and properly set the region
state as, RH_NOSYNC. Userspace must also be notified of the
failure. This is done by 'raising an event' (dm_table_event()).
If fail_mirror is called in process context the event can be raised
right away. If in interrupt context, the event is deferred to the
kmirrord thread - which raises the event if 'event_waiting' is set.
Backwards compatibility is maintained by ignoring errors if
the DM_FEATURES_HANDLE_ERRORS flag is not present.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Provided sector_t is 64 bits, reduce the in-memory footprint of the
snapshot exception table by the simple method of using unused bits of
the chunk number to combine consecutive entries.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch adds additional information to the status line. It is added at the
end of the returned text so it will not interfere with existing
implementations using this data. The addition of this information will allow
for a common return interface to match that returned with the dm-raid1.c
status line (with Jonathan Brassow's patches).
Here is a sample of what is returned with a mirror "status" call:
isw_eeaaabgfg_mirror: 0 488390920 mirror 2 8:16 8:32 3727/3727 1 AA 1 core
Here's what's returned with this patch for a stripe "status" call:
isw_dheeijjdej_stripe: 0 976783872 striped 2 8:16 8:32 1 AA
Signed-off-by: Brian Wood <brian.j.wood@intel.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch adds the stripe_end_io function to process errors that might
occur after an IO operation. As part of this there are a number of
enhancements made to record and trigger events:
- New atomic variable in struct stripe to record the number of
errors each stripe volume device has experienced (could be used
later with uevents to report back directly to userspace)
- New workqueue/work struct setup to process the trigger_event function
- New end_io function. It is here that testing for BIO error conditions
take place. It determines the exact stripe that cause the error,
records this in the new atomic variable, and calls the queue_work() function
- New trigger_event function to process failure events. This
calls dm_table_event()
Signed-off-by: Brian Wood <brian.j.wood@intel.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
