In commit a82055af59 ("netfilter: nft_payload: add VLAN offload
support"), VLAN fields in struct flow_dissector_key_vlan were unionized
with the intention of introducing another field that covered the whole TCI
header. However without a wrapping struct the subfields end up sharing the
same bits. As a result, "tc filter add ... flower vlan_id 14" specifies not
only vlan_id, but also vlan_priority.
Fix by wrapping the individual VLAN fields in a struct.
Fixes: a82055af59 ("netfilter: nft_payload: add VLAN offload support")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous commit added the ability to throttle stations when they queue
too much airtime in the hardware. This commit enables the functionality by
calculating the expected airtime usage of each packet that is dequeued from
the TXQs in mac80211, and accounting that as pending airtime.
The estimated airtime for each skb is stored in the tx_info, so we can
subtract the same amount from the running total when the skb is freed or
recycled. The throttling mechanism relies on this accounting to be
accurate (i.e., that we are not freeing skbs without subtracting any
airtime they were accounted for), so we put the subtraction into
ieee80211_report_used_skb(). As an optimisation, we also subtract the
airtime on regular TX completion, zeroing out the value stored in the
packet afterwards, to avoid having to do an expensive lookup of the station
from the packet data on every packet.
This patch does *not* include any mechanism to wake a throttled TXQ again,
on the assumption that this will happen anyway as a side effect of whatever
freed the skb (most commonly a TX completion).
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20191119060610.76681-5-kyan@google.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order for the Fq_CoDel algorithm integrated in mac80211 layer to operate
effectively to control excessive queueing latency, the CoDel algorithm
requires an accurate measure of how long packets stays in the queue, AKA
sojourn time. The sojourn time measured at the mac80211 layer doesn't
include queueing latency in the lower layer (firmware/hardware) and CoDel
expects lower layer to have a short queue. However, most 802.11ac chipsets
offload tasks such TX aggregation to firmware or hardware, thus have a deep
lower layer queue.
Without a mechanism to control the lower layer queue size, packets only
stay in mac80211 layer transiently before being sent to firmware queue.
As a result, the sojourn time measured by CoDel in the mac80211 layer is
almost always lower than the CoDel latency target, hence CoDel does little
to control the latency, even when the lower layer queue causes excessive
latency.
The Byte Queue Limits (BQL) mechanism is commonly used to address the
similar issue with wired network interface. However, this method cannot be
applied directly to the wireless network interface. "Bytes" is not a
suitable measure of queue depth in the wireless network, as the data rate
can vary dramatically from station to station in the same network, from a
few Mbps to over Gbps.
This patch implements an Airtime-based Queue Limit (AQL) to make CoDel work
effectively with wireless drivers that utilized firmware/hardware
offloading. AQL allows each txq to release just enough packets to the lower
layer to form 1-2 large aggregations to keep hardware fully utilized and
retains the rest of the frames in mac80211 layer to be controlled by the
CoDel algorithm.
Signed-off-by: Kan Yan <kyan@google.com>
[ Toke: Keep API to set pending airtime internal, fix nits in commit msg ]
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20191119060610.76681-4-kyan@google.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Felix recently added code to calculate airtime of packets to the mt76
driver. Import this into mac80211 so we can use it for airtime queue limit
calculations.
The airtime.c file is copied verbatim from the mt76 driver, and adjusted to
be usable in mac80211. This involves:
- Switching to mac80211 data structures.
- Adding support for 160 MHz channels and HE mode.
- Moving the symbol and duration calculations around a bit to avoid
rounding with the higher rates and longer symbol times used for HE rates.
The per-rate TX rate calculation is also split out to its own function so
it can be used directly for the AQL calculations later.
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20191119060610.76681-3-kyan@google.com
[fix HE_GROUP_IDX() to use 3 * bw, since there are 3 _gi values]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is alike the previous change, with some additional ipv4 specific
quirk. Even when using the route hint we still have to do perform
additional per packet checks about source address validity: a new
helper is added to wrap them.
Hints are explicitly disabled if the destination is a local broadcast,
that keeps the code simple and local broadcast are a slower path anyway.
UDP flood performances vs recvmmsg() receiver:
vanilla patched delta
Kpps Kpps %
1683 1871 +11
In the worst case scenario - each packet has a different
destination address - the performance delta is within noise
range.
v3 -> v4:
- re-enable hints for forward
v2 -> v3:
- really fix build (sic) and hint usage check
- use fib4_has_custom_rules() helpers (David A.)
- add ip_extract_route_hint() helper (Edward C.)
- use prev skb as hint instead of copying data (Willem)
v1 -> v2:
- fix build issue with !CONFIG_IP_MULTIPLE_TABLES
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So that we can use it in the next patch.
Additionally constify the helper argument.
Suggested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a per namespace counter, increment it on successful creation
of any route using the source address, decrement it on deletion
of such routes.
This allows us to check easily if the routing decision in the
current namespace depends on the packet source. Will be used
by the next patch.
Suggested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It wraps the namespace field with the same name, to easily
access it regardless of build options.
Suggested-by: David Ahern <dsahern@gmail.com>
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce the following parameters in order to add the possibility to sync
DMA memory for device before putting allocated pages in the page_pool
caches:
- PP_FLAG_DMA_SYNC_DEV: if set in page_pool_params flags, all pages that
the driver gets from page_pool will be DMA-synced-for-device according
to the length provided by the device driver. Please note DMA-sync-for-CPU
is still device driver responsibility
- offset: DMA address offset where the DMA engine starts copying rx data
- max_len: maximum DMA memory size page_pool is allowed to flush. This
is currently used in __page_pool_alloc_pages_slow routine when pages
are allocated from page allocator
These parameters are supposed to be set by device drivers.
This optimization reduces the length of the DMA-sync-for-device.
The optimization is valid because pages are initially
DMA-synced-for-device as defined via max_len. At RX time, the driver
will perform a DMA-sync-for-CPU on the memory for the packet length.
What is important is the memory occupied by packet payload, because
this is the area CPU is allowed to read and modify. As we don't track
cache-lines written into by the CPU, simply use the packet payload length
as dma_sync_size at page_pool recycle time. This also take into account
any tail-extend.
Tested-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add page_pool_update_nid() to be called by page pool consumers when they
detect numa node changes.
It will update the page pool nid value to start allocating from the new
effective numa node.
This is to mitigate page pool allocating pages from a wrong numa node,
where the pool was originally allocated, and holding on to pages that
belong to a different numa node, which causes performance degradation.
For pages that are already being consumed and could be returned to the
pool by the consumer, in next patch we will add a check per page to avoid
recycling them back to the pool and return them to the page allocator.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Match on ethertype and set up protocol dependency. Check for protocol
dependency before accessing the tci field. Allow to match on the
encapsulated ethertype too.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hardware offload support at this stage assumes an ethernet device in
place. The flow dissector provides the intermediate representation to
express this selector, so extend it to allow to store the interface
type. Flower does not uses this, so skb_flow_dissect_meta() is not
extended to match on this new field.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch constifies the pointer to source register data that is passed
as an input parameter.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bring back tls_sw_sendpage_locked. sk_msg redirection into a socket
with TLS_TX takes the following path:
tcp_bpf_sendmsg_redir
tcp_bpf_push_locked
tcp_bpf_push
kernel_sendpage_locked
sock->ops->sendpage_locked
Also update the flags test in tls_sw_sendpage_locked to allow flag
MSG_NO_SHARED_FRAGS. bpf_tcp_sendmsg sets this.
Link: https://lore.kernel.org/netdev/CA+FuTSdaAawmZ2N8nfDDKu3XLpXBbMtcCT0q4FntDD2gn8ASUw@mail.gmail.com/T/#t
Link: https://github.com/wdebruij/kerneltools/commits/icept.2
Fixes: 0608c69c9a ("bpf: sk_msg, sock{map|hash} redirect through ULP")
Fixes: f3de19af0f ("Revert \"net/tls: remove unused function tls_sw_sendpage_locked\"")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When Jonathan change the page_pool to become responsible to its
own shutdown via deferred work queue, then the disconnect_cnt
counter was removed from xdp memory model tracepoint.
This patch change the page_pool_inflight tracepoint name to
page_pool_release, because it reflects the new responsability
better. And it reintroduces a counter that reflect the number of
times page_pool_release have been tried.
The counter is also used by the code, to only empty the alloc
cache once. With a stuck work queue running every second and
counter being 64-bit, it will overrun in approx 584 billion
years. For comparison, Earth lifetime expectancy is 7.5 billion
years, before the Sun will engulf, and destroy, the Earth.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for net-next:
1) Wildcard support for the net,iface set from Kristian Evensen.
2) Offload support for matching on the input interface.
3) Simplify matching on vlan header fields.
4) Add nft_payload_rebuild_vlan_hdr() function to rebuild the vlan
header from the vlan sk_buff metadata.
5) Pass extack to nft_flow_cls_offload_setup().
6) Add C-VLAN matching support.
7) Use time64_t in xt_time to fix y2038 overflow, from Arnd Bergmann.
8) Use time_t in nft_meta to fix y2038 overflow, also from Arnd.
9) Add flow_action_entry_next() helper function to flowtable offload
infrastructure.
10) Add IPv6 support to the flowtable offload infrastructure.
11) Support for input interface matching from postrouting,
from Phil Sutter.
12) Missing check for ndo callback in flowtable offload, from wenxu.
13) Remove conntrack parameter from flow_offload_fill_dir(), from wenxu.
14) Do not pass flow_rule object for rule removal, cookie is sufficient
to achieve this.
15) Release flow_rule object in case of error from the offload commit
path.
16) Undo offload ruleset updates if transaction fails.
17) Check for error when binding flowtable callbacks, from wenxu.
18) Always unbind flowtable callbacks when unregistering hooks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The page pool keeps track of the number of pages in flight, and
it isn't safe to remove the pool until all pages are returned.
Disallow removing the pool until all pages are back, so the pool
is always available for page producers.
Make the page pool responsible for its own delayed destruction
instead of relying on XDP, so the page pool can be used without
the xdp memory model.
When all pages are returned, free the pool and notify xdp if the
pool is registered with the xdp memory system. Have the callback
perform a table walk since some drivers (cpsw) may share the pool
among multiple xdp_rxq_info.
Note that the increment of pages_state_release_cnt may result in
inflight == 0, resulting in the pool being released.
Fixes: d956a048cd ("xdp: force mem allocator removal and periodic warning")
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add nf_flow_rule_route_ipv6() and use it from the IPv6 and the inet
flowtable type definitions. Rename the nf_flow_rule_route() function to
nf_flow_rule_route_ipv4().
Adjust maximum number of actions, which now becomes 16 to leave
sufficient room for the IPv6 address mangling for NAT.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
While it is entirely possible that this tagger format is in fact more
generic than just these 2 switch families, I don't have that knowledge.
The Seville switch in NXP T1040 has a similar frame format, but there
are enough differences (e.g. DEST field starts at bit 57 instead of 56)
that calling this file tag_vitesse.c is a bit of a stretch at the
moment. The frame format has been listed in a comment so that people who
add support for further Vitesse switches can rework this tagger while
keeping compatibility with Felix.
The "ocelot" name was chosen instead of "felix" because even the Ocelot
switch can act as a DSA device when it is used in NPI mode, and the Felix
tagger format is almost identical. Currently it is only used for the
Felix switch embedded in the NXP LS1028A chip.
The ABI for this tagger should be considered "not stable" at the moment.
The DSA tag is always placed before the Ethernet header and therefore,
we are using the long prefix for RX tags to avoid putting the DSA master
port in promiscuous mode. Once there will be an API in DSA for drivers
to request DSA masters to be in promiscuous mode unconditionally, we
will switch to the "no prefix" extraction frame header, which will save
16 padding bytes for each RX frame.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the ism module is unloaded return control from exit routine only,
if all link groups are freed.
If an IB device is thrown away return control from device removal only,
if all link groups belonging to this device are freed.
A counters for the total number of SMCD link groups per ISM device is
introduced. ism module unloading continues only if the total number of
SMCD link groups for all ISM devices is zero. ISM device
removal continues only it the total number of SMCD link groups per ISM
device has decreased to zero.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SMCD link group termination is called when peer signals its shutdown
of its corresponding link group. For regular shutdowns no connections
exist anymore. For abnormal shutdowns connections must be killed and
their DMBs must be unregistered immediately. That means the SMCR method
to delay the link group freeing several seconds does not fit.
This patch adds immediate termination of a link group and its SMCD
connections and makes sure all SMCD link group related cleanup steps
are finished.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds 'module' member in the 'struct vsock_transport'
in order to get/put the transport module. This prevents the
module unloading while sockets are assigned to it.
We increase the module refcnt when a socket is assigned to a
transport, and we decrease the module refcnt when the socket
is destructed.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Jorgen Hansen <jhansen@vmware.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the support of multiple transports in the
VSOCK core.
With the multi-transports support, we can use vsock with nested VMs
(using also different hypervisors) loading both guest->host and
host->guest transports at the same time.
Major changes:
- vsock core module can be loaded regardless of the transports
- vsock_core_init() and vsock_core_exit() are renamed to
vsock_core_register() and vsock_core_unregister()
- vsock_core_register() has a feature parameter (H2G, G2H, DGRAM)
to identify which directions the transport can handle and if it's
support DGRAM (only vmci)
- each stream socket is assigned to a transport when the remote CID
is set (during the connect() or when we receive a connection request
on a listener socket).
The remote CID is used to decide which transport to use:
- remote CID <= VMADDR_CID_HOST will use guest->host transport;
- remote CID == local_cid (guest->host transport) will use guest->host
transport for loopback (host->guest transports don't support loopback);
- remote CID > VMADDR_CID_HOST will use host->guest transport;
- listener sockets are not bound to any transports since no transport
operations are done on it. In this way we can create a listener
socket, also if the transports are not loaded or with VMADDR_CID_ANY
to listen on all transports.
- DGRAM sockets are handled as before, since only the vmci_transport
provides this feature.
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All transports call __vsock_create() with the same parameters,
most of them depending on the parent socket. In order to simplify
the VSOCK core APIs exposed to the transports, this patch adds
the vsock_create_connected() callable from transports to create
a new socket when a connection request is received.
We also unexported the __vsock_create().
Suggested-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Jorgen Hansen <jhansen@vmware.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
virtio_transport and vmci_transport handle the buffer_size
sockopts in a very similar way.
In order to support multiple transports, this patch moves this
handling in the core to allow the user to change the options
also if the socket is not yet assigned to any transport.
This patch also adds the '.notify_buffer_size' callback in the
'struct virtio_transport' in order to inform the transport,
when the buffer_size is changed by the user. It is also useful
to limit the 'buffer_size' requested (e.g. virtio transports).
Acked-by: Dexuan Cui <decui@microsoft.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Jorgen Hansen <jhansen@vmware.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since now the 'struct vsock_sock' object contains a pointer to
the transport, this patch adds a parameter to the
vsock_core_get_transport() to return the right transport
assigned to the socket.
This patch modifies also the virtio_transport_get_ops(), that
uses the vsock_core_get_transport(), adding the
'struct vsock_sock *' parameter.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Jorgen Hansen <jhansen@vmware.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a preparation to support multiple transports, this patch adds
the 'transport' member at the 'struct vsock_sock'.
This new field is initialized during the creation in the
__vsock_create() function.
This patch also renames the global 'transport' pointer to
'transport_single', since for now we're only supporting a single
transport registered at run-time.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Jorgen Hansen <jhansen@vmware.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This header file now only includes the "uapi/linux/vm_sockets.h".
We can include directly it when needed.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Jorgen Hansen <jhansen@vmware.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1) New generic devlink param "enable_roce", for downstream devlink
reload support
2) Do vport ACL configuration on per vport basis when
enabling/disabling a vport. This enables to have vports enabled/disabled
outside of eswitch config for future
3) Split the code for legacy vs offloads mode and make it clear
4) Tide up vport locking and workqueue usage
5) Fix metadata enablement for ECPF
6) Make explicit use of VF property to publish IB_DEVICE_VIRTUAL_FUNCTION
7) E-Switch and flow steering core low level support and refactoring for
netfilter flowtables offload
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2019-11-13
1) Remove a unnecessary net_exit function from the xfrm interface.
From Xin Long.
2) Assign xfrm4_udp_encap_rcv to a UDP socket only if xfrm
is configured. From Alexey Dobriyan.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the dataplane hardware offload to the flowtable
infrastructure. Three new flags represent the hardware state of this
flow:
* FLOW_OFFLOAD_HW: This flow entry resides in the hardware.
* FLOW_OFFLOAD_HW_DYING: This flow entry has been scheduled to be remove
from hardware. This might be triggered by either packet path (via TCP
RST/FIN packet) or via aging.
* FLOW_OFFLOAD_HW_DEAD: This flow entry has been already removed from
the hardware, the software garbage collector can remove it from the
software flowtable.
This patch supports for:
* IPv4 only.
* Aging via FLOW_CLS_STATS, no packet and byte counter synchronization
at this stage.
This patch also adds the action callback that specifies how to convert
the flow entry into the flow_rule object that is passed to the driver.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the NFTA_FLOWTABLE_FLAGS attribute that allows users to
specify the NF_FLOWTABLE_HW_OFFLOAD flag. This patch also adds a new
setup interface for the flowtable type to perform the flowtable offload
block callback configuration.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the infrastructure to support for flow entry types.
The initial type is NF_FLOW_OFFLOAD_ROUTE that stores the routing
information into the flow entry to define a fastpath for the classic
forwarding path.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move rcu_head to struct flow_offload, then remove the flow_offload_entry
structure definition.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers do not have access to the flow_offload structure, hence remove
this union from this flow_offload object as well as the original comment
on top of it.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify this code by storing the pointer to conntrack object in the
flow_offload structure.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
after commit 4097e9d250 ("net: sched: don't use tc_action->order during
action dump"), 'act->order' is initialized but then it's no more read, so
we can just remove this member of struct tc_action.
CC: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Devlink supports pair output of name and value. When the value is
binary, it must be presented in an array. If the length of the binary
value exceeds fmsg limitation, break the value into chunks internally.
Signed-off-by: Aya Levin <ayal@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netprio uses cgroup ID to index the priority mapping table. This is
currently okay as cgroup IDs are allocated using idr and packed.
However, cgroup IDs will be changed to use full 64bit range and won't
be packed making this impractical. netprio doesn't care what type of
IDs it uses as long as they can identify the controller instances and
are packed. Let's switch to css IDs instead of cgroup IDs.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Namhyung Kim <namhyung@kernel.org>
New device parameter to enable/disable handling of RoCE traffic in the
device.
Signed-off-by: Michael Guralnik <michaelgur@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
There is a race between driver code that does setup/cleanup of device
and devlink reload operation that in some drivers works with the same
code. Use after free could we easily obtained by running:
while true; do
echo "0000:00:10.0" >/sys/bus/pci/drivers/mlxsw_spectrum2/bind
devlink dev reload pci/0000:00:10.0 &
echo "0000:00:10.0" >/sys/bus/pci/drivers/mlxsw_spectrum2/unbind
done
Fix this by enabling reload only after setup of device is complete and
disabling it at the beginning of the cleanup process.
Reported-by: Ido Schimmel <idosch@mellanox.com>
Fixes: 2d8dc5bbf4 ("devlink: Add support for reload")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One conflict in the BPF samples Makefile, some fixes in 'net' whilst
we were converting over to Makefile.target rules in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a new feature defined in section 5 of rfc7829: "Primary Path
Switchover". By introducing a new tunable parameter:
Primary.Switchover.Max.Retrans (PSMR)
The primary path will be changed to another active path when the path
error counter on the old primary path exceeds PSMR, so that "the SCTP
sender is allowed to continue data transmission on a new working path
even when the old primary destination address becomes active again".
This patch is to add this tunable parameter, 'ps_retrans' per netns,
sock, asoc and transport. It also allows a user to change ps_retrans
per netns by sysctl, and ps_retrans per sock/asoc/transport will be
initialized with it.
The check will be done in sctp_do_8_2_transport_strike() when this
feature is enabled.
Note this feature is disabled by initializing 'ps_retrans' per netns
as 0xffff by default, and its value can't be less than 'pf_retrans'
when changing by sysctl.
v3->v4:
- add define SCTP_PS_RETRANS_MAX 0xffff, and use it on extra2 of
sysctl 'ps_retrans'.
- add a new entry for ps_retrans on ip-sysctl.txt.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As said in rfc7829, section 3, point 12:
The SCTP stack SHOULD expose the PF state of its destination
addresses to the ULP as well as provide the means to notify the
ULP of state transitions of its destination addresses from
active to PF, and vice versa. However, it is recommended that
an SCTP stack implementing SCTP-PF also allows for the ULP to be
kept ignorant of the PF state of its destinations and the
associated state transitions, thus allowing for retention of the
simpler state transition model of [RFC4960] in the ULP.
Not only does it allow to expose the PF state to ULP, but also
allow to ignore sctp-pf to ULP.
So this patch is to add pf_expose per netns, sock and asoc. And in
sctp_assoc_control_transport(), ulp_notify will be set to false if
asoc->expose is not 'enabled' in next patch.
It also allows a user to change pf_expose per netns by sysctl, and
pf_expose per sock and asoc will be initialized with it.
Note that pf_expose also works for SCTP_GET_PEER_ADDR_INFO sockopt,
to not allow a user to query the state of a sctp-pf peer address
when pf_expose is 'disabled', as said in section 7.3.
v1->v2:
- Fix a build warning noticed by Nathan Chancellor.
v2->v3:
- set pf_expose to UNUSED by default to keep compatible with old
applications.
v3->v4:
- add a new entry for pf_expose on ip-sysctl.txt, as Marcelo suggested.
- change this patch to 1/5, and move sctp_assoc_control_transport
change into 2/5, as Marcelo suggested.
- use SCTP_PF_EXPOSE_UNSET instead of SCTP_PF_EXPOSE_UNUSED, and
set SCTP_PF_EXPOSE_UNSET to 0 in enum, as Marcelo suggested.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a race between driver code that does setup/cleanup of device
and devlink reload operation that in some drivers works with the same
code. Use after free could we easily obtained by running:
while true; do
echo 10 > /sys/bus/netdevsim/new_device
devlink dev reload netdevsim/netdevsim10 &
echo 10 > /sys/bus/netdevsim/del_device
done
Fix this by enabling reload only after setup of device is complete and
disabling it at the beginning of the cleanup process.
Reported-by: Ido Schimmel <idosch@mellanox.com>
Fixes: 2d8dc5bbf4 ("devlink: Add support for reload")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* typo fixes in docs
* APIs for station separation using VLAN tags rather
than separate wifi netdevs
* some preparations for upcoming features (802.3 offload
and airtime queue limits (AQL)
* stack reduction in ieee80211_assoc_success()
* use DEFINE_DEBUGFS_ATTRIBUTE in hwsim
-----BEGIN PGP SIGNATURE-----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=gDUI
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2019-11-08' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Some relatively small changes:
* typo fixes in docs
* APIs for station separation using VLAN tags rather
than separate wifi netdevs
* some preparations for upcoming features (802.3 offload
and airtime queue limits (AQL)
* stack reduction in ieee80211_assoc_success()
* use DEFINE_DEBUGFS_ATTRIBUTE in hwsim
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This provides an alternative mechanism for AP VLAN support where a
single netdev is used with VLAN tagged frames instead of separate
netdevs for each VLAN without tagged frames from the WLAN driver.
By setting NL80211_EXT_FEATURE_VLAN_OFFLOAD flag the driver indicates
support for a single netdev with VLAN tagged frames. Separate
VLAN-specific netdevs can be added using RTM_NEWLINK/IFLA_VLAN_ID
similarly to Ethernet. NL80211_CMD_NEW_KEY (for group keys),
NL80211_CMD_NEW_STATION, and NL80211_CMD_SET_STATION will optionally
specify vlan_id using NL80211_ATTR_VLAN_ID.
Signed-off-by: Gurumoorthi Gnanasambandhan <gguru@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Link: https://lore.kernel.org/r/20191031214640.5012-1-jouni@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To implement airtime queue limiting, we need to keep a running account of
the estimated airtime of all skbs queued into the device. Do to this
correctly, we need to store the airtime estimate into the skb so we can
decrease the outstanding balance when the skb is freed. This means that the
time estimate must be stored somewhere that will survive for the lifetime
of the skb.
To get this, decrease the size of the ack_frame_id field to 6 bits, and
lower the size of the ID space accordingly. This leaves 10 bits for use for
tx_time_est, which is enough to store a maximum of 4096 us, if we shift the
values so they become units of 4us.
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/157182474063.150713.16132669599100802716.stgit@toke.dk
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The FQ implementation used by mac80211 allocates memory using kmalloc(),
which can fail; and Johannes reported that this actually happens in
practice.
To avoid this, switch the allocation to kvmalloc() instead; this also
brings fq_impl in line with all the FQ qdiscs.
Fixes: 557fc4a098 ("fq: add fair queuing framework")
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20191105155750.547379-1-toke@redhat.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add layer 3 generic packet exception traps that can report trapped
packets and documentation of the traps.
Unlike drop traps, these exception traps also need to inject the packet
to the kernel's receive path. For example, a packet that was trapped due
to unreachable neighbour need to be injected into the kernel so that it
will trigger an ARP request or a neighbour solicitation message.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add packet traps that can report packets that were dropped during layer
3 forwarding.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_make_synack() already uses tcp_clock_ns(), and can pass
the value to cookie_init_timestamp() to avoid another call
to ktime_get_ns() helper.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
1) Missing register size validation in bitwise and cmp offloads.
2) Fix error code in ip_set_sockfn_get() when copy_to_user() fails,
from Dan Carpenter.
3) Oneliner to copy MAC address in IPv6 hash:ip,mac sets, from
Stefano Brivio.
4) Missing policy validation in ipset with NL_VALIDATE_STRICT,
from Jozsef Kadlecsik.
5) Fix unaligned access to private data area of nf_tables instructions,
from Lukas Wunner.
6) Relax check for object updates, reported as a regression by
Eric Garver, patch from Fernando Fernandez Mancera.
7) Crash on ebtables dnat extension when used from the output path.
From Florian Westphal.
8) Fix bogus EOPNOTSUPP when updating basechain flags.
9) Fix bogus EBUSY when updating a basechain that is already offloaded.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
TLS TX needs to release and re-acquire the socket lock if send buffer
fills up.
TLS SW TX path currently depends on only allowing one thread to enter
the function by the abuse of sk_write_pending. If another writer is
already waiting for memory no new ones are allowed in.
This has two problems:
- writers don't wake other threads up when they leave the kernel;
meaning that this scheme works for single extra thread (second
application thread or delayed work) because memory becoming
available will send a wake up request, but as Mallesham and
Pooja report with larger number of threads it leads to threads
being put to sleep indefinitely;
- the delayed work does not get _scheduled_ but it may _run_ when
other writers are present leading to crashes as writers don't
expect state to change under their feet (same records get pushed
and freed multiple times); it's hard to reliably bail from the
work, however, because the mere presence of a writer does not
guarantee that the writer will push pending records before exiting.
Ensuring wakeups always happen will make the code basically open
code a mutex. Just use a mutex.
The TLS HW TX path does not have any locking (not even the
sk_write_pending hack), yet it uses a per-socket sg_tx_data
array to push records.
Fixes: a42055e8d2 ("net/tls: Add support for async encryption of records for performance")
Reported-by: Mallesham Jatharakonda <mallesh537@gmail.com>
Reported-by: Pooja Trivedi <poojatrivedi@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sk->sk_max_ack_backlog can be read without any lock being held
at least in TCP/DCCP cases.
We need to use READ_ONCE()/WRITE_ONCE() to avoid load/store tearing
and/or potential KCSAN warnings.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sk->sk_ack_backlog can be read without any lock being held.
We need to use READ_ONCE()/WRITE_ONCE() to avoid load/store tearing
and/or potential KCSAN warnings.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are common instances of the following construct :
if (n->confirmed != now)
n->confirmed = now;
A C compiler could legally remove the conditional.
Use READ_ONCE()/WRITE_ONCE() to avoid this problem.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a couple of READ_ONCE() and WRITE_ONCE() to prevent
load-tearing and store-tearing in sock_read_timestamp()
and sock_write_timestamp()
This might prevent another KCSAN report.
Fixes: 3a0ed3e961 ("sock: Make sock->sk_stamp thread-safe")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Deepa Dinamani <deepa.kernel@gmail.com>
Acked-by: Deepa Dinamani <deepa.kernel@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After this change, qdisc packet counter is no longer
a 32bit quantity. We still export 32bit values to user.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
gnet_stats_basic_packed was really meant to be private kernel structure.
If this proves to be a problem, we will have to rename the in-kernel
version.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add wrappers around the devlink resource API, so that DSA drivers can
register and unregister devlink resources.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a new filter is added to cls_api, the function
tcf_chain_tp_insert_unique() looks up the protocol/priority/chain to
determine if the tcf_proto is duplicated in the chain's hashtable. It then
creates a new entry or continues with an existing one. In cls_flower, this
allows the function fl_ht_insert_unque to determine if a filter is a
duplicate and reject appropriately, meaning that the duplicate will not be
passed to drivers via the offload hooks. However, when a tcf_proto is
destroyed it is removed from its chain before a hardware remove hook is
hit. This can lead to a race whereby the driver has not received the
remove message but duplicate flows can be accepted. This, in turn, can
lead to the offload driver receiving incorrect duplicate flows and out of
order add/delete messages.
Prevent duplicates by utilising an approach suggested by Vlad Buslov. A
hash table per block stores each unique chain/protocol/prio being
destroyed. This entry is only removed when the full destroy (and hardware
offload) has completed. If a new flow is being added with the same
identiers as a tc_proto being detroyed, then the add request is replayed
until the destroy is complete.
Fixes: 8b64678e0a ("net: sched: refactor tp insert/delete for concurrent execution")
Signed-off-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reported-by: Louis Peens <louis.peens@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since de77ecd4ef ("bonding: improve link-status update in
mii-monitoring"), the bonding driver has utilized two separate variables
to indicate the next link state a particular slave should transition to.
Each is used to communicate to a different portion of the link state
change commit logic; one to the bond_miimon_commit function itself, and
another to the state transition logic.
Unfortunately, the two variables can become unsynchronized,
resulting in incorrect link state transitions within bonding. This can
cause slaves to become stuck in an incorrect link state until a
subsequent carrier state transition.
The issue occurs when a special case in bond_slave_netdev_event
sets slave->link directly to BOND_LINK_FAIL. On the next pass through
bond_miimon_inspect after the slave goes carrier up, the BOND_LINK_FAIL
case will set the proposed next state (link_new_state) to BOND_LINK_UP,
but the new_link to BOND_LINK_DOWN. The setting of the final link state
from new_link comes after that from link_new_state, and so the slave
will end up incorrectly in _DOWN state.
Resolve this by combining the two variables into one.
Reported-by: Aleksei Zakharov <zakharov.a.g@yandex.ru>
Reported-by: Sha Zhang <zhangsha.zhang@huawei.com>
Cc: Mahesh Bandewar <maheshb@google.com>
Fixes: de77ecd4ef ("bonding: improve link-status update in mii-monitoring")
Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Invoking the following commands on a 32-bit architecture with strict
alignment requirements (such as an ARMv7-based Raspberry Pi) results
in an alignment exception:
# nft add table ip test-ip4
# nft add chain ip test-ip4 output { type filter hook output priority 0; }
# nft add rule ip test-ip4 output quota 1025 bytes
Alignment trap: not handling instruction e1b26f9f at [<7f4473f8>]
Unhandled fault: alignment exception (0x001) at 0xb832e824
Internal error: : 1 [#1] PREEMPT SMP ARM
Hardware name: BCM2835
[<7f4473fc>] (nft_quota_do_init [nft_quota])
[<7f447448>] (nft_quota_init [nft_quota])
[<7f4260d0>] (nf_tables_newrule [nf_tables])
[<7f4168dc>] (nfnetlink_rcv_batch [nfnetlink])
[<7f416bd0>] (nfnetlink_rcv [nfnetlink])
[<8078b334>] (netlink_unicast)
[<8078b664>] (netlink_sendmsg)
[<8071b47c>] (sock_sendmsg)
[<8071bd18>] (___sys_sendmsg)
[<8071ce3c>] (__sys_sendmsg)
[<8071ce94>] (sys_sendmsg)
The reason is that nft_quota_do_init() calls atomic64_set() on an
atomic64_t which is only aligned to 32-bit, not 64-bit, because it
succeeds struct nft_expr in memory which only contains a 32-bit pointer.
Fix by aligning the nft_expr private data to 64-bit.
Fixes: 96518518cc ("netfilter: add nftables")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v3.13+
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2019-11-02
The following pull-request contains BPF updates for your *net-next* tree.
We've added 30 non-merge commits during the last 7 day(s) which contain
a total of 41 files changed, 1864 insertions(+), 474 deletions(-).
The main changes are:
1) Fix long standing user vs kernel access issue by introducing
bpf_probe_read_user() and bpf_probe_read_kernel() helpers, from Daniel.
2) Accelerated xskmap lookup, from Björn and Maciej.
3) Support for automatic map pinning in libbpf, from Toke.
4) Cleanup of BTF-enabled raw tracepoints, from Alexei.
5) Various fixes to libbpf and selftests.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The only slightly tricky merge conflict was the netdevsim because the
mutex locking fix overlapped a lot of driver reload reorganization.
The rest were (relatively) trivial in nature.
Signed-off-by: David S. Miller <davem@davemloft.net>
In this commit the XSKMAP entry lookup function used by the XDP
redirect code is moved from the xskmap.c file to the xdp_sock.h
header, so the lookup can be inlined from, e.g., the
bpf_xdp_redirect_map() function.
Further the __xsk_map_redirect() and __xsk_map_flush() is moved to the
xsk.c, which lets the compiler inline the xsk_rcv() and xsk_flush()
functions.
Finally, all the XDP socket functions were moved from linux/bpf.h to
net/xdp_sock.h, where most of the XDP sockets functions are anyway.
This yields a ~2% performance boost for the xdpsock "rx_drop"
scenario.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20191101110346.15004-4-bjorn.topel@gmail.com
Now that the DSA ports are listed in the switch fabric, there is
no need to store the dsa_switch structures from the drivers in the
fabric anymore. So get rid of the dst->ds static array.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers do not use the ds->rtable static arrays anymore, get rid of it.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement a new list of DSA links in the switch fabric itself, to
provide an alterative to the ds->rtable static arrays.
At the same time, provide a new dsa_routing_port() helper to abstract
the usage of ds->rtable in drivers. If there's no port to reach a
given device, return the first invalid port, ds->num_ports. This avoids
potential signedness errors or the need to define special values.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend struct tc_action with new "tcfa_flags" field. Set the field in
tcf_idr_create() function and provide new helper
tcf_idr_create_from_flags() that derives 'cpustats' boolean from flags
value. Update individual hardware-offloaded actions init() to pass their
"flags" argument to new helper in order to skip percpu stats allocation
when user requested it through flags.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend TCA_ACT space with nla_bitfield32 flags. Add
TCA_ACT_FLAGS_NO_PERCPU_STATS as the only allowed flag. Parse the flags in
tcf_action_init_1() and pass resulting value as additional argument to
a_o->init().
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify stats update helper functions introduced in previous patches in this
series to fallback to regular tc_action->tcfa_{b|q}stats if cpu stats are
not allocated for the action argument. If regular non-percpu allocated
counters are in use, then obtain action tcfa_lock while modifying them.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previous commit introduced helper function for updating qstats and
refactored set of actions to use the helpers, instead of modifying qstats
directly. However, one of the affected action exposes its qstats to
skb_tc_reinsert(), which then modifies it.
Refactor skb_tc_reinsert() to return integer error code and don't increment
overlimit qstats in case of error, and use the returned error code in
tcf_mirred_act() to manually increment the overlimit counter with new
helper function.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extract common code that increments cpu_qstats counters into standalone act
API functions. Change hardware offloaded actions that use percpu counter
allocation to use the new functions instead of accessing cpu_qstats
directly.
This commit doesn't change functionality.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extract common code that increments cpu_bstats counter into standalone act
API function. Change hardware offloaded actions that use percpu counter
allocation to use the new function instead of incrementing cpu_bstats
directly.
This commit doesn't change functionality.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, all implementations of tc_action_ops->stats_update() callback
have almost exactly the same implementation of counters update
code (besides gact which also updates drop counter). In order to simplify
support for using both percpu-allocated and regular action counters
depending on run-time flag in following patches, extract action counters
update code into standalone function in act API.
This commit doesn't change functionality.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ICMP flow dissector currently parses only the Type and Code fields.
Some ICMP packets (echo, timestamp) have a 16 bit Identifier field which
is used to correlate packets.
Add such field in flow_dissector_key_icmp and replace skb_flow_get_be16()
with a more complex function which populate this field.
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Documents two piece of code which can't be understood at a glance.
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only smc-related reference in net/sock.h is struct smc_hashinfo.
But just its address is refered to. Thus there is no need for the
include of net/smc.h. Remove it.
Suggested-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return directly from within the loop as soon as the port is found,
otherwise we won't return NULL if the end of the list is reached.
Fixes: b96ddf254b ("net: dsa: use ports list in dsa_to_port")
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add plumbing to allow DSA drivers to register parameters with devlink.
To keep with the abstraction, the DSA drivers pass the ds structure to
these helpers, and the DSA core then translates that to the devlink
structure associated to the device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
sk_page_frag() optimizes skb_frag allocations by using per-task
skb_frag cache when it knows it's the only user. The condition is
determined by seeing whether the socket allocation mask allows
blocking - if the allocation may block, it obviously owns the task's
context and ergo exclusively owns current->task_frag.
Unfortunately, this misses recursion through memory reclaim path.
Please take a look at the following backtrace.
[2] RIP: 0010:tcp_sendmsg_locked+0xccf/0xe10
...
tcp_sendmsg+0x27/0x40
sock_sendmsg+0x30/0x40
sock_xmit.isra.24+0xa1/0x170 [nbd]
nbd_send_cmd+0x1d2/0x690 [nbd]
nbd_queue_rq+0x1b5/0x3b0 [nbd]
__blk_mq_try_issue_directly+0x108/0x1b0
blk_mq_request_issue_directly+0xbd/0xe0
blk_mq_try_issue_list_directly+0x41/0xb0
blk_mq_sched_insert_requests+0xa2/0xe0
blk_mq_flush_plug_list+0x205/0x2a0
blk_flush_plug_list+0xc3/0xf0
[1] blk_finish_plug+0x21/0x2e
_xfs_buf_ioapply+0x313/0x460
__xfs_buf_submit+0x67/0x220
xfs_buf_read_map+0x113/0x1a0
xfs_trans_read_buf_map+0xbf/0x330
xfs_btree_read_buf_block.constprop.42+0x95/0xd0
xfs_btree_lookup_get_block+0x95/0x170
xfs_btree_lookup+0xcc/0x470
xfs_bmap_del_extent_real+0x254/0x9a0
__xfs_bunmapi+0x45c/0xab0
xfs_bunmapi+0x15/0x30
xfs_itruncate_extents_flags+0xca/0x250
xfs_free_eofblocks+0x181/0x1e0
xfs_fs_destroy_inode+0xa8/0x1b0
destroy_inode+0x38/0x70
dispose_list+0x35/0x50
prune_icache_sb+0x52/0x70
super_cache_scan+0x120/0x1a0
do_shrink_slab+0x120/0x290
shrink_slab+0x216/0x2b0
shrink_node+0x1b6/0x4a0
do_try_to_free_pages+0xc6/0x370
try_to_free_mem_cgroup_pages+0xe3/0x1e0
try_charge+0x29e/0x790
mem_cgroup_charge_skmem+0x6a/0x100
__sk_mem_raise_allocated+0x18e/0x390
__sk_mem_schedule+0x2a/0x40
[0] tcp_sendmsg_locked+0x8eb/0xe10
tcp_sendmsg+0x27/0x40
sock_sendmsg+0x30/0x40
___sys_sendmsg+0x26d/0x2b0
__sys_sendmsg+0x57/0xa0
do_syscall_64+0x42/0x100
entry_SYSCALL_64_after_hwframe+0x44/0xa9
In [0], tcp_send_msg_locked() was using current->page_frag when it
called sk_wmem_schedule(). It already calculated how many bytes can
be fit into current->page_frag. Due to memory pressure,
sk_wmem_schedule() called into memory reclaim path which called into
xfs and then IO issue path. Because the filesystem in question is
backed by nbd, the control goes back into the tcp layer - back into
tcp_sendmsg_locked().
nbd sets sk_allocation to (GFP_NOIO | __GFP_MEMALLOC) which makes
sense - it's in the process of freeing memory and wants to be able to,
e.g., drop clean pages to make forward progress. However, this
confused sk_page_frag() called from [2]. Because it only tests
whether the allocation allows blocking which it does, it now thinks
current->page_frag can be used again although it already was being
used in [0].
After [2] used current->page_frag, the offset would be increased by
the used amount. When the control returns to [0],
current->page_frag's offset is increased and the previously calculated
number of bytes now may overrun the end of allocated memory leading to
silent memory corruptions.
Fix it by adding gfpflags_normal_context() which tests sleepable &&
!reclaim and use it to determine whether to use current->task_frag.
v2: Eric didn't like gfp flags being tested twice. Introduce a new
helper gfpflags_normal_context() and combine the two tests.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Josef Bacik <josef@toxicpanda.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix misspellings of "disconnect", "disconnecting", "connections", and
"disconnected".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS fixes for net
The following patchset contains Netfilter/IPVS fixes for net:
1) Fix crash on flowtable due to race between garbage collection
and insertion.
2) Restore callback unbinding in netfilter offloads.
3) Fix races on IPVS module removal, from Davide Caratti.
4) Make old_secure_tcp per-netns to fix sysbot report,
from Eric Dumazet.
5) Validate matching length in netfilter offloads, from wenxu.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter/IPVS updates for net-next,
more specifically:
* Updates for ipset:
1) Coding style fix for ipset comment extension, from Jeremy Sowden.
2) De-inline many functions in ipset, from Jeremy Sowden.
3) Move ipset function definition from header to source file.
4) Move ip_set_put_flags() to source, export it as a symbol, remove
inline.
5) Move range_to_mask() to the source file where this is used.
6) Move ip_set_get_ip_port() to the source file where this is used.
* IPVS selftests and netns improvements:
7) Two patches to speedup ipvs netns dismantle, from Haishuang Yan.
8) Three patches to add selftest script for ipvs, also from
Haishuang Yan.
* Conntrack updates and new nf_hook_slow_list() function:
9) Document ct ecache extension, from Florian Westphal.
10) Skip ct extensions from ctnetlink dump, from Florian.
11) Free ct extension immediately, from Florian.
12) Skip access to ecache extension from nf_ct_deliver_cached_events()
this is not correct as reported by Syzbot.
13) Add and use nf_hook_slow_list(), from Florian.
* Flowtable infrastructure updates:
14) Move priority to nf_flowtable definition.
15) Dynamic allocation of per-device hooks in flowtables.
16) Allow to include netdevice only once in flowtable definitions.
17) Rise maximum number of devices per flowtable.
* Netfilter hardware offload infrastructure updates:
18) Add nft_flow_block_chain() helper function.
19) Pass callback list to nft_setup_cb_call().
20) Add nft_flow_cls_offload_setup() helper function.
21) Remove rules for the unregistered device via netdevice event.
22) Support for multiple devices in a basechain definition at the
ingress hook.
22) Add nft_chain_offload_cmd() helper function.
23) Add nft_flow_block_offload_init() helper function.
24) Rewind in case of failing to bind multiple devices to hook.
25) Typo in IPv6 tproxy module description, from Norman Rasmussen.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In rtnl_net_notifyid(), we certainly can't pass a null GFP flag to
rtnl_notify(). A GFP_KERNEL flag would be fine in most circumstances,
but there are a few paths calling rtnl_net_notifyid() from atomic
context or from RCU critical sections. The later also precludes the use
of gfp_any() as it wouldn't detect the RCU case. Also, the nlmsg_new()
call is wrong too, as it uses GFP_KERNEL unconditionally.
Therefore, we need to pass the GFP flags as parameter and propagate it
through function calls until the proper flags can be determined.
In most cases, GFP_KERNEL is fine. The exceptions are:
* openvswitch: ovs_vport_cmd_get() and ovs_vport_cmd_dump()
indirectly call rtnl_net_notifyid() from RCU critical section,
* rtnetlink: rtmsg_ifinfo_build_skb() already receives GFP flags as
parameter.
Also, in ovs_vport_cmd_build_info(), let's change the GFP flags used
by nlmsg_new(). The function is allowed to sleep, so better make the
flags consistent with the ones used in the following
ovs_vport_cmd_fill_info() call.
Found by code inspection.
Fixes: 9a9634545c ("netns: notify netns id events")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If CONFIG_NET_HWBM is not set, then these stub functions in
<net/hwbm.h> should be declared static to avoid trying to
export them from any driver that includes this.
Fixes the following sparse warnings:
./include/net/hwbm.h:24:6: warning: symbol 'hwbm_buf_free' was not declared. Should it be static?
./include/net/hwbm.h:25:5: warning: symbol 'hwbm_pool_refill' was not declared. Should it be static?
./include/net/hwbm.h:26:5: warning: symbol 'hwbm_pool_add' was not declared. Should it be static?
Signed-off-by: Ben Dooks (Codethink) <ben.dooks@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes variables and callback these are related to the nested
device structure.
devices that can be nested have their own nest_level variable that
represents the depth of nested devices.
In the previous patch, new {lower/upper}_level variables are added and
they replace old private nest_level variable.
So, this patch removes all 'nest_level' variables.
In order to avoid lockdep warning, ->ndo_get_lock_subclass() was added
to get lockdep subclass value, which is actually lower nested depth value.
But now, they use the dynamic lockdep key to avoid lockdep warning instead
of the subclass.
So, this patch removes ->ndo_get_lock_subclass() callback.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All bonding device has same lockdep key and subclass is initialized with
nest_level.
But actual nest_level value can be changed when a lower device is attached.
And at this moment, the subclass should be updated but it seems to be
unsafe.
So this patch makes bonding use dynamic lockdep key instead of the
subclass.
Test commands:
ip link add bond0 type bond
for i in {1..5}
do
let A=$i-1
ip link add bond$i type bond
ip link set bond$i master bond$A
done
ip link set bond5 master bond0
Splat looks like:
[ 307.992912] WARNING: possible recursive locking detected
[ 307.993656] 5.4.0-rc3+ #96 Tainted: G W
[ 307.994367] --------------------------------------------
[ 307.995092] ip/761 is trying to acquire lock:
[ 307.995710] ffff8880513aac60 (&(&bond->stats_lock)->rlock#2/2){+.+.}, at: bond_get_stats+0xb8/0x500 [bonding]
[ 307.997045]
but task is already holding lock:
[ 307.997923] ffff88805fcbac60 (&(&bond->stats_lock)->rlock#2/2){+.+.}, at: bond_get_stats+0xb8/0x500 [bonding]
[ 307.999215]
other info that might help us debug this:
[ 308.000251] Possible unsafe locking scenario:
[ 308.001137] CPU0
[ 308.001533] ----
[ 308.001915] lock(&(&bond->stats_lock)->rlock#2/2);
[ 308.002609] lock(&(&bond->stats_lock)->rlock#2/2);
[ 308.003302]
*** DEADLOCK ***
[ 308.004310] May be due to missing lock nesting notation
[ 308.005319] 3 locks held by ip/761:
[ 308.005830] #0: ffffffff9fcc42b0 (rtnl_mutex){+.+.}, at: rtnetlink_rcv_msg+0x466/0x8a0
[ 308.006894] #1: ffff88805fcbac60 (&(&bond->stats_lock)->rlock#2/2){+.+.}, at: bond_get_stats+0xb8/0x500 [bonding]
[ 308.008243] #2: ffffffff9f9219c0 (rcu_read_lock){....}, at: bond_get_stats+0x9f/0x500 [bonding]
[ 308.009422]
stack backtrace:
[ 308.010124] CPU: 0 PID: 761 Comm: ip Tainted: G W 5.4.0-rc3+ #96
[ 308.011097] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[ 308.012179] Call Trace:
[ 308.012601] dump_stack+0x7c/0xbb
[ 308.013089] __lock_acquire+0x269d/0x3de0
[ 308.013669] ? register_lock_class+0x14d0/0x14d0
[ 308.014318] lock_acquire+0x164/0x3b0
[ 308.014858] ? bond_get_stats+0xb8/0x500 [bonding]
[ 308.015520] _raw_spin_lock_nested+0x2e/0x60
[ 308.016129] ? bond_get_stats+0xb8/0x500 [bonding]
[ 308.017215] bond_get_stats+0xb8/0x500 [bonding]
[ 308.018454] ? bond_arp_rcv+0xf10/0xf10 [bonding]
[ 308.019710] ? rcu_read_lock_held+0x90/0xa0
[ 308.020605] ? rcu_read_lock_sched_held+0xc0/0xc0
[ 308.021286] ? bond_get_stats+0x9f/0x500 [bonding]
[ 308.021953] dev_get_stats+0x1ec/0x270
[ 308.022508] bond_get_stats+0x1d1/0x500 [bonding]
Fixes: d3fff6c443 ("net: add netdev_lockdep_set_classes() helper")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
syzbot reported the following issue :
BUG: KCSAN: data-race in update_defense_level / update_defense_level
read to 0xffffffff861a6260 of 4 bytes by task 3006 on cpu 1:
update_defense_level+0x621/0xb30 net/netfilter/ipvs/ip_vs_ctl.c:177
defense_work_handler+0x3d/0xd0 net/netfilter/ipvs/ip_vs_ctl.c:225
process_one_work+0x3d4/0x890 kernel/workqueue.c:2269
worker_thread+0xa0/0x800 kernel/workqueue.c:2415
kthread+0x1d4/0x200 drivers/block/aoe/aoecmd.c:1253
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:352
write to 0xffffffff861a6260 of 4 bytes by task 7333 on cpu 0:
update_defense_level+0xa62/0xb30 net/netfilter/ipvs/ip_vs_ctl.c:205
defense_work_handler+0x3d/0xd0 net/netfilter/ipvs/ip_vs_ctl.c:225
process_one_work+0x3d4/0x890 kernel/workqueue.c:2269
worker_thread+0xa0/0x800 kernel/workqueue.c:2415
kthread+0x1d4/0x200 drivers/block/aoe/aoecmd.c:1253
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:352
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 7333 Comm: kworker/0:5 Not tainted 5.4.0-rc3+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: events defense_work_handler
Indeed, old_secure_tcp is currently a static variable, while it
needs to be a per netns variable.
Fixes: a0840e2e16 ("IPVS: netns, ip_vs_ctl local vars moved to ipvs struct.")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
UDP IPv6 packets auto flowlabels are using a 32bit secret
(static u32 hashrnd in net/core/flow_dissector.c) and
apply jhash() over fields known by the receivers.
Attackers can easily infer the 32bit secret and use this information
to identify a device and/or user, since this 32bit secret is only
set at boot time.
Really, using jhash() to generate cookies sent on the wire
is a serious security concern.
Trying to change the rol32(hash, 16) in ip6_make_flowlabel() would be
a dead end. Trying to periodically change the secret (like in sch_sfq.c)
could change paths taken in the network for long lived flows.
Let's switch to siphash, as we did in commit df453700e8
("inet: switch IP ID generator to siphash")
Using a cryptographically strong pseudo random function will solve this
privacy issue and more generally remove other weak points in the stack.
Packet schedulers using skb_get_hash_perturb() benefit from this change.
Fixes: b56774163f ("ipv6: Enable auto flow labels by default")
Fixes: 42240901f7 ("ipv6: Implement different admin modes for automatic flow labels")
Fixes: 67800f9b1f ("ipv6: Call skb_get_hash_flowi6 to get skb->hash in ip6_make_flowlabel")
Fixes: cb1ce2ef38 ("ipv6: Implement automatic flow label generation on transmit")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Jonathan Berger <jonathann1@walla.com>
Reported-by: Amit Klein <aksecurity@gmail.com>
Reported-by: Benny Pinkas <benny@pinkas.net>
Cc: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows you to register one netdev basechain to multiple
devices. This adds a new NFTA_HOOK_DEVS netlink attribute to specify
the list of netdevices. Basechains store a list of hooks.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Rise the maximum limit of devices per flowtable up to 256. Rename
NFT_FLOWTABLE_DEVICE_MAX to NFT_NETDEVICE_MAX in preparation to reuse
the netdev hook parser for ingress basechain.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Hardware offload needs access to the priority field, store this field in
the nf_flowtable object.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Now that ports are dynamically listed in the fabric, there is no need
to provide a special helper to allocate the dsa_switch structure. This
will give more flexibility to drivers to embed this structure as they
wish in their private structure.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Allocate the struct dsa_port the first time it is accessed with
dsa_port_touch, and remove the static dsa_port array from the
dsa_switch structure.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Use the new ports list instead of iterating over switches and their
ports when setting up the default CPU port. Unassign it on teardown.
Now that we can iterate over multiple CPU ports, remove dst->cpu_dp.
At the same time, provide a better error message for CPU-less tree.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Use the new ports list instead of iterating over switches and their
ports when setting up the switches and their ports.
At the same time, provide setup states and messages for ports and
switches as it is done for the trees.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Use the new ports list instead of accessing the dsa_switch array
of ports in the dsa_to_port helper.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Add a list of switch ports within the switch fabric. This will help the
lookup of a port inside the whole fabric, and it is the first step
towards supporting multiple CPU ports, before deprecating the usage of
the unique dst->cpu_dp pointer.
In preparation for a future allocation of the dsa_port structures,
return -ENOMEM in case no structure is returned, even though this
error cannot be reached yet.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Do not let the drivers access the ds->ports static array directly
while there is a dsa_to_port helper for this purpose.
At the same time, un-const this helper since the SJA1105 driver
assigns the priv member of the returned dsa_port structure.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
This patch removes the iph field from the state structure, which is not
properly initialized. Instead, add a new field to make the "do we want
to set DF" be the state bit and move the code to set the DF flag from
ip_frag_next().
Joint work with Pablo and Linus.
Fixes: 19c3401a91 ("net: ipv4: place control buffer handling away from fragmentation iterators")
Reported-by: Patrick Schönthaler <patrick@notvads.ovh>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Intel test robot reported a ~7% regression on TCP_CRR tests
that they bisected to the cited commit.
Indeed, every time a new TCP socket is created or deleted,
the atomic counter net->count is touched (via get_net(net)
and put_net(net) calls)
So cpus might have to reload a contended cache line in
net_hash_mix(net) calls.
We need to reorder 'struct net' fields to move @hash_mix
in a read mostly cache line.
We move in the first cache line fields that can be
dirtied often.
We probably will have to address in a followup patch
the __randomize_layout that was added in linux-4.13,
since this might break our placement choices.
Fixes: 355b985537 ("netns: provide pure entropy for net_hash_mix()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: kernel test robot <oliver.sang@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of waiting for rcu grace period just free it directly.
This is safe because conntrack lookup doesn't consider extensions.
Other accesses happen while ct->ext can't be free'd, either because
a ct refcount was taken or because the conntrack hash bucket lock or
the dying list spinlock have been taken.
This allows to remove __krealloc in a followup patch, netfilter was the
only user.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
* minstrel improvements from Felix
* a TX aggregation simplification
* some additional capabilities for hwsim
* minor cleanups & docs updates
-----BEGIN PGP SIGNATURE-----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=IJ7D
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2019-10-11' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
A few more small things, nothing really stands out:
* minstrel improvements from Felix
* a TX aggregation simplification
* some additional capabilities for hwsim
* minor cleanups & docs updates
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
For the sake of tcp_poll(), there are few places where we fetch
sk->sk_wmem_queued while this field can change from IRQ or other cpu.
We need to add READ_ONCE() annotations, and also make sure write
sides use corresponding WRITE_ONCE() to avoid store-tearing.
sk_wmem_queued_add() helper is added so that we can in
the future convert to ADD_ONCE() or equivalent if/when
available.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the sake of tcp_poll(), there are few places where we fetch
sk->sk_sndbuf while this field can change from IRQ or other cpu.
We need to add READ_ONCE() annotations, and also make sure write
sides use corresponding WRITE_ONCE() to avoid store-tearing.
Note that other transports probably need similar fixes.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the sake of tcp_poll(), there are few places where we fetch
sk->sk_rcvbuf while this field can change from IRQ or other cpu.
We need to add READ_ONCE() annotations, and also make sure write
sides use corresponding WRITE_ONCE() to avoid store-tearing.
Note that other transports probably need similar fixes.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are few places where we fetch tp->snd_nxt while
this field can change from IRQ or other cpu.
We need to add READ_ONCE() annotations, and also make
sure write sides use corresponding WRITE_ONCE() to avoid
store-tearing.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are few places where we fetch tp->write_seq while
this field can change from IRQ or other cpu.
We need to add READ_ONCE() annotations, and also make
sure write sides use corresponding WRITE_ONCE() to avoid
store-tearing.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During health reporter operations, driver might want to fill-up
the extack message, so propagate extack down to the health reporter ops.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sk->sk_backlog.len can be written by BH handlers, and read
from process contexts in a lockless way.
Note the write side should also use WRITE_ONCE() or a variant.
We need some agreement about the best way to do this.
syzbot reported :
BUG: KCSAN: data-race in tcp_add_backlog / tcp_grow_window.isra.0
write to 0xffff88812665f32c of 4 bytes by interrupt on cpu 1:
sk_add_backlog include/net/sock.h:934 [inline]
tcp_add_backlog+0x4a0/0xcc0 net/ipv4/tcp_ipv4.c:1737
tcp_v4_rcv+0x1aba/0x1bf0 net/ipv4/tcp_ipv4.c:1925
ip_protocol_deliver_rcu+0x51/0x470 net/ipv4/ip_input.c:204
ip_local_deliver_finish+0x110/0x140 net/ipv4/ip_input.c:231
NF_HOOK include/linux/netfilter.h:305 [inline]
NF_HOOK include/linux/netfilter.h:299 [inline]
ip_local_deliver+0x133/0x210 net/ipv4/ip_input.c:252
dst_input include/net/dst.h:442 [inline]
ip_rcv_finish+0x121/0x160 net/ipv4/ip_input.c:413
NF_HOOK include/linux/netfilter.h:305 [inline]
NF_HOOK include/linux/netfilter.h:299 [inline]
ip_rcv+0x18f/0x1a0 net/ipv4/ip_input.c:523
__netif_receive_skb_one_core+0xa7/0xe0 net/core/dev.c:5004
__netif_receive_skb+0x37/0xf0 net/core/dev.c:5118
netif_receive_skb_internal+0x59/0x190 net/core/dev.c:5208
napi_skb_finish net/core/dev.c:5671 [inline]
napi_gro_receive+0x28f/0x330 net/core/dev.c:5704
receive_buf+0x284/0x30b0 drivers/net/virtio_net.c:1061
virtnet_receive drivers/net/virtio_net.c:1323 [inline]
virtnet_poll+0x436/0x7d0 drivers/net/virtio_net.c:1428
napi_poll net/core/dev.c:6352 [inline]
net_rx_action+0x3ae/0xa50 net/core/dev.c:6418
read to 0xffff88812665f32c of 4 bytes by task 7292 on cpu 0:
tcp_space include/net/tcp.h:1373 [inline]
tcp_grow_window.isra.0+0x6b/0x480 net/ipv4/tcp_input.c:413
tcp_event_data_recv+0x68f/0x990 net/ipv4/tcp_input.c:717
tcp_rcv_established+0xbfe/0xf50 net/ipv4/tcp_input.c:5618
tcp_v4_do_rcv+0x381/0x4e0 net/ipv4/tcp_ipv4.c:1542
sk_backlog_rcv include/net/sock.h:945 [inline]
__release_sock+0x135/0x1e0 net/core/sock.c:2427
release_sock+0x61/0x160 net/core/sock.c:2943
tcp_recvmsg+0x63b/0x1a30 net/ipv4/tcp.c:2181
inet_recvmsg+0xbb/0x250 net/ipv4/af_inet.c:838
sock_recvmsg_nosec net/socket.c:871 [inline]
sock_recvmsg net/socket.c:889 [inline]
sock_recvmsg+0x92/0xb0 net/socket.c:885
sock_read_iter+0x15f/0x1e0 net/socket.c:967
call_read_iter include/linux/fs.h:1864 [inline]
new_sync_read+0x389/0x4f0 fs/read_write.c:414
__vfs_read+0xb1/0xc0 fs/read_write.c:427
vfs_read fs/read_write.c:461 [inline]
vfs_read+0x143/0x2c0 fs/read_write.c:446
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 7292 Comm: syz-fuzzer Not tainted 5.3.0+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
sock_rcvlowat() or int_sk_rcvlowat() might be called without the socket
lock for example from tcp_poll().
Use READ_ONCE() to document the fact that other cpus might change
sk->sk_rcvlowat under us and avoid KCSAN splats.
Use WRITE_ONCE() on write sides too.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
tcp_memory_pressure is read without holding any lock,
and its value could be changed on other cpus.
Use READ_ONCE() to annotate these lockless reads.
The write side is already using atomic ops.
Fixes: b8da51ebb1 ("tcp: introduce tcp_under_memory_pressure()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
reqsk_queue_empty() is called from inet_csk_listen_poll() while
other cpus might write ->rskq_accept_head value.
Use {READ|WRITE}_ONCE() to avoid compiler tricks
and potential KCSAN splats.
Fixes: fff1f3001c ("tcp: add a spinlock to protect struct request_sock_queue")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Add a "going_away" indication to ISM devices and IB ports and
avoid creation of new connections on such disappearing devices.
And do not handle ISM events if ISM device is disappearing.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
This patch introduces separate locks for the split SMCD and SMCR
link group lists.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Currently SMCD and SMCR link groups are maintained in one list.
To facilitate abnormal termination handling they are split into
a separate list for SMCR link groups and separate lists for SMCD
link groups per SMCD device.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
This patch is to add a new event SCTP_SEND_FAILED_EVENT described in
rfc6458#section-6.1.11. It's a update of SCTP_SEND_FAILED event:
struct sctp_sndrcvinfo ssf_info is replaced with
struct sctp_sndinfo ssfe_info in struct sctp_send_failed_event.
SCTP_SEND_FAILED is being deprecated, but we don't remove it in this
patch. Both are being processed in sctp_datamsg_destroy() when the
corresp event flag is set.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
A helper sctp_ulpevent_nofity_peer_addr_change() will be extracted
to make peer_addr_change event and enqueue it, and the helper will
be called in sctp_assoc_add_peer() to send SCTP_ADDR_ADDED event.
This event is described in rfc6458#section-6.1.2:
SCTP_ADDR_ADDED: The address is now part of the association.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
This patch is to fix a NULL-ptr deref in selinux_socket_connect_helper:
[...] kasan: GPF could be caused by NULL-ptr deref or user memory access
[...] RIP: 0010:selinux_socket_connect_helper+0x94/0x460
[...] Call Trace:
[...] selinux_sctp_bind_connect+0x16a/0x1d0
[...] security_sctp_bind_connect+0x58/0x90
[...] sctp_process_asconf+0xa52/0xfd0 [sctp]
[...] sctp_sf_do_asconf+0x785/0x980 [sctp]
[...] sctp_do_sm+0x175/0x5a0 [sctp]
[...] sctp_assoc_bh_rcv+0x285/0x5b0 [sctp]
[...] sctp_backlog_rcv+0x482/0x910 [sctp]
[...] __release_sock+0x11e/0x310
[...] release_sock+0x4f/0x180
[...] sctp_accept+0x3f9/0x5a0 [sctp]
[...] inet_accept+0xe7/0x720
It was caused by that the 'newsk' sk_socket was not set before going to
security sctp hook when processing asconf chunk with SCTP_PARAM_ADD_IP
or SCTP_PARAM_SET_PRIMARY:
inet_accept()->
sctp_accept():
lock_sock():
lock listening 'sk'
do_softirq():
sctp_rcv(): <-- [1]
asconf chunk arrives and
enqueued in 'sk' backlog
sctp_sock_migrate():
set asoc's sk to 'newsk'
release_sock():
sctp_backlog_rcv():
lock 'newsk'
sctp_process_asconf() <-- [2]
unlock 'newsk'
sock_graft():
set sk_socket <-- [3]
As it shows, at [1] the asconf chunk would be put into the listening 'sk'
backlog, as accept() was holding its sock lock. Then at [2] asconf would
get processed with 'newsk' as asoc's sk had been set to 'newsk'. However,
'newsk' sk_socket is not set until [3], while selinux_sctp_bind_connect()
would deref it, then kernel crashed.
Here to fix it by adding the chunk to sk_backlog until newsk sk_socket is
set when .accept() is done.
Note that sk->sk_socket can be NULL when the sock is closed, so SOCK_DEAD
flag is also needed to check in sctp_newsk_ready().
Thanks to Ondrej for reviewing the code.
Fixes: d452930fd3 ("selinux: Add SCTP support")
Reported-by: Ying Xu <yinxu@redhat.com>
Suggested-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
If IPsec is not configured, there is no reason to delay the inevitable.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
* allow scanning when operating on radar channels in
ETSI regdomains
* accept deauth frames in IBSS - we have code to parse
and handle them, but were dropping them early
* fix an allocation failure path in hwsim
* fix a failure path memory leak in nl80211 FTM code
* fix RCU handling & locking in multi-BSSID parsing
* reject malformed SSID in mac80211 (this shouldn't
really be able to happen, but defense in depth)
* avoid userspace buffer overrun in ancient wext code
if SSID was too long
-----BEGIN PGP SIGNATURE-----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=k685
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2019-10-08' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
A number of fixes:
* allow scanning when operating on radar channels in
ETSI regdomains
* accept deauth frames in IBSS - we have code to parse
and handle them, but were dropping them early
* fix an allocation failure path in hwsim
* fix a failure path memory leak in nl80211 FTM code
* fix RCU handling & locking in multi-BSSID parsing
* reject malformed SSID in mac80211 (this shouldn't
really be able to happen, but defense in depth)
* avoid userspace buffer overrun in ancient wext code
if SSID was too long
====================
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
In non-ETSI regulatory domains scan is blocked when operating channel
is a DFS channel. For ETSI, however, once DFS channel is marked as
available after the CAC, this channel will remain available (for some
time) even after leaving this channel.
Therefore a scan can be done without any impact on the availability
of the DFS channel as no new CAC is required after the scan.
Enable scan in mac80211 in these cases.
Signed-off-by: Aaron Komisar <aaron.komisar@tandemg.com>
Link: https://lore.kernel.org/r/1570024728-17284-1-git-send-email-aaron.komisar@tandemg.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use a single bit instead of boolean to remember if packet
was already decrypted.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Store async_capable on a single bit instead of a full integer
to save space.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid unnecessary pointer chasing and calculations, callers already
have most of the state tls_device_decrypted() needs.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
genl_family_attrbuf() function is no longer used by anyone, so remove it.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the dumpit info struct for attrs. Instead of existing attribute
validation do parse them and save in the info struct. Caller can benefit
from this and does not have to do parse itself. In order to properly
free attrs, genl_family pointer needs to be added to dumpit info struct
as well.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the cb->data is taken by ops during non-parallel dumping.
Introduce a new structure genl_dumpit_info and store the ops there.
Distribute the info to both non-parallel and parallel dumping. Also add
a helper genl_dumpit_info() to easily get the info structure in the
dumpit callback from cb.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For newly allocated devlink instance allow drivers to set net struct
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a skeleton structure for adding TLS statistics.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add tracing of device-related interaction to aid performance
analysis, especially around resync:
tls:tls_device_offload_set
tls:tls_device_rx_resync_send
tls:tls_device_rx_resync_nh_schedule
tls:tls_device_rx_resync_nh_delay
tls:tls_device_tx_resync_req
tls:tls_device_tx_resync_send
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tls_hw_* functions are quite confusingly named, since they
are related to the TOE-offload, not TLS_HW offload which doesn't
require TOE. Rename them.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move tls_hw_* functions to a new, separate source file
to avoid confusion with normal, non-TOE offload.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename struct tls_device to struct tls_toe_device to avoid
confusion with normal, non-TOE offload.
No functional changes.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move tls_device structure and register/unregister functions
to a new header to avoid confusion with normal, non-TOE offload.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All devlink instances are created in init_net and stay there for a
lifetime. Allow user to be able to move devlink instances into
namespaces during devlink reload operation. That ensures proper
re-instantiation of driver objects, including netdevices.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow drivers to get net struct for devlink instance.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since errors are propagated all the way up to the caller, propagate
possible extack of the caller all the way down to the notifier block
callback.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike events for registered notifier, during the registration, the
errors that happened for the block being registered are not propagated
up to the caller. Make sure the error is propagated for FIB rules and
entries.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently all users of FIB notifier only cares about events in init_net.
Later in this patchset, users get interested in other namespaces too.
However, for every registered block user is interested only about one
namespace. Make the FIB notifier registration per-netns and avoid
unnecessary calls of notifier block for other namespaces.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There really is no need to make drivers call the
ieee80211_start_tx_ba_cb_irqsafe() function and then
schedule the worker if all we want is to set a bit.
Add a new return value (that was previously considered
invalid) to indicate that the driver is immediately
ready for the session, and make drivers use it. The
only drivers that remain different are the Intel ones
as they need to negotiate more with the firmware.
Link: https://lore.kernel.org/r/1570007543-I152912660131cbab2e5d80b4218238c20f8a06e5@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The struct __dsa_skb_cb is supposed to span the entire 48-byte skb
control block, while the struct dsa_skb_cb only the portion of it which
is used by the DSA core (the rest is available as private data to
drivers).
The DSA_SKB_CB and __DSA_SKB_CB helpers are supposed to help retrieve
this pointer based on a skb, but it turns out there is nobody directly
interested in the struct __dsa_skb_cb in the kernel. So remove it.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Often the code for example in drivers is interested in getting notifier
call only from certain network namespace. In addition to the existing
global netdevice notifier chain introduce per-netns chains and allow
users to register to that. Eventually this would eliminate unnecessary
overhead in case there are many netdevices in many network namespaces.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Push iterations over net namespaces and netdevices from
register_netdevice_notifier() and unregister_netdevice_notifier()
into helper functions. Along with that introduce continue_reverse macros
to make the code a bit nicer allowing to get rid of "last" marks.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_twsk_unique() has a hard coded assumption about ipv4 loopback
being 127/8
Lets instead use the standard ipv4_is_loopback() method,
in a new ipv6_addr_v4mapped_loopback() helper.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
1) Add NFT_CHAIN_POLICY_UNSET to replace hardcoded -1 to
specify that the chain policy is unset. The chain policy
field is actually defined as an 8-bit unsigned integer.
2) Remove always true condition reported by smatch in
chain policy check.
3) Fix element lookup on dynamic sets, from Florian Westphal.
4) Use __u8 in ebtables uapi header, from Masahiro Yamada.
5) Bogus EBUSY when removing flowtable after chain flush,
from Laura Garcia Liebana.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
ctl packets sent on behalf of TIME_WAIT sockets currently
have a zero skb->priority, which can cause various problems.
In this patch we :
- add a tw_priority field in struct inet_timewait_sock.
- populate it from sk->sk_priority when a TIME_WAIT is created.
- For IPv4, change ip_send_unicast_reply() and its two
callers to propagate tw_priority correctly.
ip_send_unicast_reply() no longer changes sk->sk_priority.
- For IPv6, make sure TIME_WAIT sockets pass their tw_priority
field to tcp_v6_send_response() and tcp_v6_send_ack().
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, ip6_xmit() sets skb->priority based on sk->sk_priority
This is not desirable for TCP since TCP shares the same ctl socket
for a given netns. We want to be able to send RST or ACK packets
with a non zero skb->priority.
This patch has no functional change.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The deletion of a flowtable after a flush in the same transaction
results in EBUSY. This patch adds an activation and deactivation of
flowtables in order to update the _use_ counter.
Signed-off-by: Laura Garcia Liebana <nevola@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Julian noted that rt_uses_gateway has a more subtle use than 'is gateway
set':
https://lore.kernel.org/netdev/alpine.LFD.2.21.1909151104060.2546@ja.home.ssi.bg/
Revert that part of the commit referenced in the Fixes tag.
Currently, there are no u8 holes in 'struct rtable'. There is a 4-byte hole
in the second cacheline which contains the gateway declaration. So move
rt_gw_family down to the gateway declarations since they are always used
together, and then re-use that u8 for rt_uses_gateway. End result is that
rtable size is unchanged.
Fixes: 1550c17193 ("ipv4: Prepare rtable for IPv6 gateway")
Reported-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Default policy is defined as a unsigned 8-bit field, do not use a
negative value to leave it unset, use this new NFT_CHAIN_POLICY_UNSET
instead.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Pull networking updates from David Miller:
1) Support IPV6 RA Captive Portal Identifier, from Maciej Żenczykowski.
2) Use bio_vec in the networking instead of custom skb_frag_t, from
Matthew Wilcox.
3) Make use of xmit_more in r8169 driver, from Heiner Kallweit.
4) Add devmap_hash to xdp, from Toke Høiland-Jørgensen.
5) Support all variants of 5750X bnxt_en chips, from Michael Chan.
6) More RTNL avoidance work in the core and mlx5 driver, from Vlad
Buslov.
7) Add TCP syn cookies bpf helper, from Petar Penkov.
8) Add 'nettest' to selftests and use it, from David Ahern.
9) Add extack support to drop_monitor, add packet alert mode and
support for HW drops, from Ido Schimmel.
10) Add VLAN offload to stmmac, from Jose Abreu.
11) Lots of devm_platform_ioremap_resource() conversions, from
YueHaibing.
12) Add IONIC driver, from Shannon Nelson.
13) Several kTLS cleanups, from Jakub Kicinski.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1930 commits)
mlxsw: spectrum_buffers: Add the ability to query the CPU port's shared buffer
mlxsw: spectrum: Register CPU port with devlink
mlxsw: spectrum_buffers: Prevent changing CPU port's configuration
net: ena: fix incorrect update of intr_delay_resolution
net: ena: fix retrieval of nonadaptive interrupt moderation intervals
net: ena: fix update of interrupt moderation register
net: ena: remove all old adaptive rx interrupt moderation code from ena_com
net: ena: remove ena_restore_ethtool_params() and relevant fields
net: ena: remove old adaptive interrupt moderation code from ena_netdev
net: ena: remove code duplication in ena_com_update_nonadaptive_moderation_interval _*()
net: ena: enable the interrupt_moderation in driver_supported_features
net: ena: reimplement set/get_coalesce()
net: ena: switch to dim algorithm for rx adaptive interrupt moderation
net: ena: add intr_moder_rx_interval to struct ena_com_dev and use it
net: phy: adin: implement Energy Detect Powerdown mode via phy-tunable
ethtool: implement Energy Detect Powerdown support via phy-tunable
xen-netfront: do not assume sk_buff_head list is empty in error handling
s390/ctcm: Delete unnecessary checks before the macro call “dev_kfree_skb”
net: ena: don't wake up tx queue when down
drop_monitor: Better sanitize notified packets
...
Pull crypto updates from Herbert Xu:
"API:
- Add the ability to abort a skcipher walk.
Algorithms:
- Fix XTS to actually do the stealing.
- Add library helpers for AES and DES for single-block users.
- Add library helpers for SHA256.
- Add new DES key verification helper.
- Add surrounding bits for ESSIV generator.
- Add accelerations for aegis128.
- Add test vectors for lzo-rle.
Drivers:
- Add i.MX8MQ support to caam.
- Add gcm/ccm/cfb/ofb aes support in inside-secure.
- Add ofb/cfb aes support in media-tek.
- Add HiSilicon ZIP accelerator support.
Others:
- Fix potential race condition in padata.
- Use unbound workqueues in padata"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (311 commits)
crypto: caam - Cast to long first before pointer conversion
crypto: ccree - enable CTS support in AES-XTS
crypto: inside-secure - Probe transform record cache RAM sizes
crypto: inside-secure - Base RD fetchcount on actual RD FIFO size
crypto: inside-secure - Base CD fetchcount on actual CD FIFO size
crypto: inside-secure - Enable extended algorithms on newer HW
crypto: inside-secure: Corrected configuration of EIP96_TOKEN_CTRL
crypto: inside-secure - Add EIP97/EIP197 and endianness detection
padata: remove cpu_index from the parallel_queue
padata: unbind parallel jobs from specific CPUs
padata: use separate workqueues for parallel and serial work
padata, pcrypt: take CPU hotplug lock internally in padata_alloc_possible
crypto: pcrypt - remove padata cpumask notifier
padata: make padata_do_parallel find alternate callback CPU
workqueue: require CPU hotplug read exclusion for apply_workqueue_attrs
workqueue: unconfine alloc/apply/free_workqueue_attrs()
padata: allocate workqueue internally
arm64: dts: imx8mq: Add CAAM node
random: Use wait_event_freezable() in add_hwgenerator_randomness()
crypto: ux500 - Fix COMPILE_TEST warnings
...
DSA currently handles shared block filters (for the classifier-action
qdisc) in the core due to what I believe are simply pragmatic reasons -
hiding the complexity from drivers and offerring a simple API for port
mirroring.
Extend the dsa_slave_setup_tc function by passing all other qdisc
offloads to the driver layer, where the driver may choose what it
implements and how. DSA is simply a pass-through in this case.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows taprio to offload the schedule enforcement to capable
network cards, resulting in more precise windows and less CPU usage.
The gate mask acts on traffic classes (groups of queues of same
priority), as specified in IEEE 802.1Q-2018, and following the existing
taprio and mqprio semantics.
It is up to the driver to perform conversion between tc and individual
netdev queues if for some reason it needs to make that distinction.
Full offload is requested from the network interface by specifying
"flags 2" in the tc qdisc creation command, which in turn corresponds to
the TCA_TAPRIO_ATTR_FLAG_FULL_OFFLOAD bit.
The important detail here is the clockid which is implicitly /dev/ptpN
for full offload, and hence not configurable.
A reference counting API is added to support the use case where Ethernet
drivers need to keep the taprio offload structure locally (i.e. they are
a multi-port switch driver, and configuring a port depends on the
settings of other ports as well). The refcount_t variable is kept in a
private structure (__tc_taprio_qopt_offload) and not exposed to drivers.
In the future, the private structure might also be expanded with a
backpointer to taprio_sched *q, to implement the notification system
described in the patch (of when admin became oper, or an error occurred,
etc, so the offload can be monitored with 'tc qdisc show').
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When filling in hardware intermediate representation tc_setup_flow_action()
directly obtains, checks and takes reference to dev used by mirred action,
instead of using act->ops->get_dev() API created specifically for this
purpose. In order to remove code duplication, refactor flow_action infra to
use action API when obtaining mirred action target dev. Extend get_dev()
with additional argument that is used to provide dev destructor to the
user.
Fixes: 5a6ff4b13d ("net: sched: take reference to action dev before calling offloads")
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With recent patch set that removed rtnl lock dependency from cls hardware
offload API rtnl lock is only taken when reading action data and can be
released after action-specific data is parsed into intermediate
representation. However, sample action psample group is passed by pointer
without obtaining reference to it first, which makes it possible to
concurrently overwrite the action and deallocate object pointed by
psample_group pointer after rtnl lock is released but before driver
finished using the pointer.
To prevent such race condition, obtain reference to psample group while it
is used by flow_action infra. Extend psample API with function
psample_group_take() that increments psample group reference counter.
Extend struct tc_action_ops with new get_psample_group() API. Implement the
API for action sample using psample_group_take() and already existing
psample_group_put() as a destructor. Use it in tc_setup_flow_action() to
take reference to psample group pointed to by entry->sample.psample_group
and release it in tc_cleanup_flow_action().
Disable bh when taking psample_groups_lock. The lock is now taken while
holding action tcf_lock that is used by data path and requires bh to be
disabled, so doing the same for psample_groups_lock is necessary to
preserve SOFTIRQ-irq-safety.
Fixes: 918190f50e ("net: sched: flower: don't take rtnl lock for cls hw offloads API")
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Generalize flow_action_entry cleanup by extending the structure with
pointer to destructor function. Set the destructor in
tc_setup_flow_action(). Refactor tc_cleanup_flow_action() to call
entry->destructor() instead of using switch that dispatches by entry->id
and manually executes cleanup.
This refactoring is necessary for following patches in this series that
require destructor to use tc_action->ops callbacks that can't be easily
obtained in tc_cleanup_flow_action().
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
UDP reuseport groups can hold a mix unconnected and connected sockets.
Ensure that connections only receive all traffic to their 4-tuple.
Fast reuseport returns on the first reuseport match on the assumption
that all matches are equal. Only if connections are present, return to
the previous behavior of scoring all sockets.
Record if connections are present and if so (1) treat such connected
sockets as an independent match from the group, (2) only return
2-tuple matches from reuseport and (3) do not return on the first
2-tuple reuseport match to allow for a higher scoring match later.
New field has_conns is set without locks. No other fields in the
bitmap are modified at runtime and the field is only ever set
unconditionally, so an RMW cannot miss a change.
Fixes: e32ea7e747 ("soreuseport: fast reuseport UDP socket selection")
Link: http://lkml.kernel.org/r/CA+FuTSfRP09aJNYRt04SS6qj22ViiOEWaWmLAwX0psk8-PGNxw@mail.gmail.com
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Craig Gallek <kraig@google.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The test implemented by some_qdisc_is_busy() is somewhat loosy for
NOLOCK qdisc, as we may hit the following scenario:
CPU1 CPU2
// in net_tx_action()
clear_bit(__QDISC_STATE_SCHED...);
// in some_qdisc_is_busy()
val = (qdisc_is_running(q) ||
test_bit(__QDISC_STATE_SCHED,
&q->state));
// here val is 0 but...
qdisc_run(q)
// ... CPU1 is going to run the qdisc next
As a conseguence qdisc_run() in net_tx_action() can race with qdisc_reset()
in dev_qdisc_reset(). Such race is not possible for !NOLOCK qdisc as
both the above bit operations are under the root qdisc lock().
After commit 021a17ed79 ("pfifo_fast: drop unneeded additional lock on dequeue")
the race can cause use after free and/or null ptr dereference, but the root
cause is likely older.
This patch addresses the issue explicitly checking for deactivation under
the seqlock for NOLOCK qdisc, so that the qdisc_run() in the critical
scenario becomes a no-op.
Note that the enqueue() op can still execute concurrently with dev_qdisc_reset(),
but that is safe due to the skb_array() locking, and we can't avoid that
for NOLOCK qdiscs.
Fixes: 021a17ed79 ("pfifo_fast: drop unneeded additional lock on dequeue")
Reported-by: Li Shuang <shuali@redhat.com>
Reported-and-tested-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the fact that devlink reload failed is stored in drivers.
Move this flag into devlink core. Also, expose it to the user.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to properly implement failure indication during reload,
split the reload op into two ops, one for down phase and one for
up phase.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable setting skb->mark for UDP and RAW sockets using cmsg.
This is analogous to existing support for TOS, TTL, txtime, etc.
Packet sockets already support this as of commit c7d39e3263
("packet: support per-packet fwmark for af_packet sendmsg").
Similar to other fields, implement by
1. initialize the sockcm_cookie.mark from socket option sk_mark
2. optionally overwrite this in ip_cmsg_send/ip6_datagram_send_ctl
3. initialize inet_cork.mark from sockcm_cookie.mark
4. initialize each (usually just one) skb->mark from inet_cork.mark
Step 1 is handled in one location for most protocols by ipcm_init_sk
as of commit 351782067b ("ipv4: ipcm_cookie initializers").
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for net-next:
1) Fix error path of nf_tables_updobj(), from Dan Carpenter.
2) Move large structure away from stack in the nf_tables offload
infrastructure, from Arnd Bergmann.
3) Move indirect flow_block logic to nf_tables_offload.
4) Support for synproxy objects, from Fernando Fernandez Mancera.
5) Support for fwd and dup offload.
6) Add __nft_offload_get_chain() helper, this implicitly fixes missing
mutex and check for offload flags in the indirect block support,
patch from wenxu.
7) Remove rules on device unregistration, from wenxu. This includes
two preparation patches to reuse nft_flow_offload_chain() and
nft_flow_offload_rule().
Large batch from Jeremy Sowden to make a second pass to the
CONFIG_HEADER_TEST support and a bit of housekeeping:
8) Missing include guard in conntrack label header, from Jeremy Sowden.
9) A few coding style errors: trailing whitespace, incorrect indent in
Kconfig, and semicolons at the end of function definitions.
10) Remove unused ipt_init() and ip6t_init() declarations.
11) Inline xt_hashlimit, ebt_802_3 and xt_physdev headers. They are
only used once.
12) Update include directive in several netfilter files.
13) Remove unused include/net/netfilter/ipv6/nf_conntrack_icmpv6.h.
14) Move nf_ip6_ext_hdr() to include/linux/netfilter_ipv6.h
15) Move several synproxy structure definitions to nf_synproxy.h
16) Move nf_bridge_frag_data structure to include/linux/netfilter_bridge.h
17) Clean up static inline definitions in nf_conntrack_ecache.h.
18) Replace defined(CONFIG...) || defined(CONFIG...MODULE) with IS_ENABLED(CONFIG...).
19) Missing inline function conditional definitions based on Kconfig
preferences in synproxy and nf_conntrack_timeout.
20) Update br_nf_pre_routing_ipv6() definition.
21) Move conntrack code in linux/skbuff.h to nf_conntrack headers.
22) Several patches to remove superfluous CONFIG_NETFILTER and
CONFIG_NF_CONNTRACK checks in headers, coming from the initial batch
support for CONFIG_HEADER_TEST for netfilter.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Two inline functions defined in nf_conntrack_timestamp.h,
`nf_ct_tstamp_enabled` and `nf_ct_set_tstamp`, are not called anywhere.
Remove them.
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
nf_conntrack_zones.h was wrapped in a CONFIG_NF_CONNTRACK check in order
to fix compilation failures:
37ee3d5b3e ("netfilter: nf_defrag_ipv4: fix compilation error with NF_CONNTRACK=n")
Subsequent changes mean that these failures will no longer occur and the
check is unnecessary. Remove it.
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
`struct nf_hook_ops`, `struct nf_hook_state` and the `nf_hookfn`
function typedef appear in function and struct declarations and
definitions in a number of netfilter headers. The structs and typedef
themselves are defined by linux/netfilter.h but only when
CONFIG_NETFILTER is enabled. Define them unconditionally and add
forward declarations in order to remove CONFIG_NETFILTER conditionals
from the other headers.
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
There is a superfluous `#if IS_ENABLED(CONFIG_NF_CONNTRACK)` check
wrapping some function declarations. Remove it.
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Move some `struct nf_conntrack` code from linux/skbuff.h to
linux/nf_conntrack_common.h. Together with a couple of helpers for
getting and setting skb->_nfct, it allows us to remove
CONFIG_NF_CONNTRACK checks from net/netfilter/nf_conntrack.h.
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The real br_nf_pre_routing_ipv6 function, defined when CONFIG_IPV6 is
enabled, expects `void *priv`, not `const struct nf_hook_ops *ops`.
Update the stub br_nf_pre_routing_ipv6, defined when CONFIG_IPV6 is
disabled, to match.
Fixes: 06198b34a3 ("netfilter: Pass priv instead of nf_hook_ops to netfilter hooks")
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
nf_conntrack_synproxy.h contains three inline functions. The contents
of two of them are wrapped in CONFIG_NETFILTER_SYNPROXY checks and just
return NULL if it is not enabled. The third does nothing if they return
NULL, so wrap its contents as well.
nf_ct_timeout_data is only called if CONFIG_NETFILTER_TIMEOUT is
enabled. Wrap its contents in a CONFIG_NETFILTER_TIMEOUT check like the
other inline functions in nf_conntrack_timeout.h.
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
A few headers contain instances of:
#if defined(CONFIG_XXX) or defined(CONFIG_XXX_MODULE)
Replace them with:
#if IS_ENABLED(CONFIG_XXX)
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The header contains some inline functions defined as:
static inline f (...)
{
#ifdef CONFIG_NF_CONNTRACK_EVENTS
...
#else
...
#endif
}
and a few others as:
#ifdef CONFIG_NF_CONNTRACK_EVENTS
static inline f (...)
{
...
}
#else
static inline f (...)
{
...
}
#endif
Prefer the former style, which is more numerous.
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
There is a struct definition function in nf_conntrack_bridge.h which is
not specific to conntrack and is used elswhere in netfilter. Move it
into netfilter_bridge.h.
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
There is some non-conntrack code in the nf_conntrack_synproxy.h header.
Move it to the nf_synproxy.h header.
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
nf_conntrack_icmpv6.h contains two object macros which duplicate macros
in linux/icmpv6.h. The latter definitions are also visible wherever it
is included, so remove it.
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Include some headers in files which require them, and remove others
which are not required.
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Several header-files, Kconfig files and Makefiles have trailing
white-space. Remove it.
In netfilter/Kconfig, indent the type of CONFIG_NETFILTER_NETLINK_ACCT
correctly.
There are semicolons at the end of two function definitions in
include/net/netfilter/nf_conntrack_acct.h and
include/net/netfilter/nf_conntrack_ecache.h. Remove them.
Fix indentation in nf_conntrack_l4proto.h.
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
nf_conntrack_labels.h has no include guard. Add it.
The comment following the #endif in the nf_flow_table.h include guard
referred to the wrong macro. Fix it.
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
If the net_device unregisters, clean up the offload rules before the
chain is destroy.
Signed-off-by: wenxu <wenxu@ucloud.cn>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
* a fix in the new 6 GHz channel support
* a fix for recent minstrel (rate control) updates
for an infinite loop
* handle interface type changes better wrt. management frame
registrations (for management frames sent to userspace)
* add in-BSS RX time to survey information
* handle HW rfkill properly if !CONFIG_RFKILL
* send deauth on IBSS station expiry, to avoid state mismatches
* handle deferred crypto tailroom updates in mac80211 better
when device restart happens
* fix a spectre-v1 - really a continuation of a previous patch
* advertise NL80211_CMD_UPDATE_FT_IES as supported if so
* add some missing parsing in VHT extended NSS support
* support HE in mac80211_hwsim
* let mac80211 drivers determine the max MTU themselves
along with the usual cleanups etc.
-----BEGIN PGP SIGNATURE-----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=HAuT
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2019-09-11' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
We have a number of changes, but things are settling down:
* a fix in the new 6 GHz channel support
* a fix for recent minstrel (rate control) updates
for an infinite loop
* handle interface type changes better wrt. management frame
registrations (for management frames sent to userspace)
* add in-BSS RX time to survey information
* handle HW rfkill properly if !CONFIG_RFKILL
* send deauth on IBSS station expiry, to avoid state mismatches
* handle deferred crypto tailroom updates in mac80211 better
when device restart happens
* fix a spectre-v1 - really a continuation of a previous patch
* advertise NL80211_CMD_UPDATE_FT_IES as supported if so
* add some missing parsing in VHT extended NSS support
* support HE in mac80211_hwsim
* let mac80211 drivers determine the max MTU themselves
along with the usual cleanups etc.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Make it possibly for drivers to adjust the default max_mtu
by storing it in the hardware struct and using that value
for all interfaces.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Link: https://lore.kernel.org/r/1567738137-31748-1-git-send-email-wgong@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds support for packet mirroring and redirection. The
nft_fwd_dup_netdev_offload() function configures the flow_action object
for the fwd and the dup actions.
Extend nft_flow_rule_destroy() to release the net_device object when the
flow_rule object is released, since nft_fwd_dup_netdev_offload() bumps
the net_device reference counter.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: wenxu <wenxu@ucloud.cn>
Add the 'reset_dev_on_drv_probe' devlink parameter, controlling the
device reset policy on driver probe.
This parameter is useful in conjunction with the existing
'fw_load_policy' parameter.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add nft_offload_init() and nft_offload_exit() function to deal with the
init and the exit path of the offload infrastructure.
Rename nft_indr_block_get_and_ing_cmd() to nft_indr_block_cb().
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Johan Hedberg says:
====================
pull request: bluetooth-next 2019-09-06
Here's the main bluetooth-next pull request for the 5.4 kernel.
- Cleanups & fixes to btrtl driver
- Fixes for Realtek devices in btusb, e.g. for suspend handling
- Firmware loading support for BCM4345C5
- hidp_send_message() return value handling fixes
- Added support for utilizing Fast Advertising Interval
- Various other minor cleanups & fixes
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
No need for fib_notifier_ops to be in struct net. It is used only by
fib_notifier as a private data. Use net_generic to introduce per-net
fib_notifier struct and move fib_notifier_ops there.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for net-next:
1) Add nft_reg_store64() and nft_reg_load64() helpers, from Ander Juaristi.
2) Time matching support, also from Ander Juaristi.
3) VLAN support for nfnetlink_log, from Michael Braun.
4) Support for set element deletions from the packet path, also from Ander.
5) Remove __read_mostly from conntrack spinlock, from Li RongQing.
6) Support for updating stateful objects, this also includes the initial
client for this infrastructure: the quota extension. A follow up fix
for the control plane also comes in this batch. Patches from
Fernando Fernandez Mancera.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Add the ability to use unaligned chunks in the AF_XDP umem. By
relaxing where the chunks can be placed, it allows to use an
arbitrary buffer size and place whenever there is a free
address in the umem. Helps more seamless DPDK AF_XDP driver
integration. Support for i40e, ixgbe and mlx5e, from Kevin and
Maxim.
2) Addition of a wakeup flag for AF_XDP tx and fill rings so the
application can wake up the kernel for rx/tx processing which
avoids busy-spinning of the latter, useful when app and driver
is located on the same core. Support for i40e, ixgbe and mlx5e,
from Magnus and Maxim.
3) bpftool fixes for printf()-like functions so compiler can actually
enforce checks, bpftool build system improvements for custom output
directories, and addition of 'bpftool map freeze' command, from Quentin.
4) Support attaching/detaching XDP programs from 'bpftool net' command,
from Daniel.
5) Automatic xskmap cleanup when AF_XDP socket is released, and several
barrier/{read,write}_once fixes in AF_XDP code, from Björn.
6) Relicense of bpf_helpers.h/bpf_endian.h for future libbpf
inclusion as well as libbpf versioning improvements, from Andrii.
7) Several new BPF kselftests for verifier precision tracking, from Alexei.
8) Several BPF kselftest fixes wrt endianess to run on s390x, from Ilya.
9) And more BPF kselftest improvements all over the place, from Stanislav.
10) Add simple BPF map op cache for nfp driver to batch dumps, from Jakub.
11) AF_XDP socket umem mapping improvements for 32bit archs, from Ivan.
12) Add BPF-to-BPF call and BTF line info support for s390x JIT, from Yauheni.
13) Small optimization in arm64 JIT to spare 1 insns for BPF_MOD, from Jerin.
14) Fix an error check in bpf_tcp_gen_syncookie() helper, from Petar.
15) Various minor fixes and cleanups, from Nathan, Masahiro, Masanari,
Peter, Wei, Yue.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net): ipsec 2019-09-05
1) Several xfrm interface fixes from Nicolas Dichtel:
- Avoid an interface ID corruption on changelink.
- Fix wrong intterface names in the logs.
- Fix a list corruption when changing network namespaces.
- Fix unregistation of the underying phydev.
2) Fix a potential warning when merging xfrm_plocy nodes.
From Florian Westphal.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Changes made to add support for fast advertising interval
as per core 4.1 specification, section 9.3.11.2.
A peripheral device entering any of the following GAP modes and
sending either non-connectable advertising events or scannable
undirected advertising events should use adv_fast_interval2
(100ms - 150ms) for adv_fast_period(30s).
- Non-Discoverable Mode
- Non-Connectable Mode
- Limited Discoverable Mode
- General Discoverable Mode
Signed-off-by: Spoorthi Ravishankar Koppad <spoorthix.k@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When creating a v4 route that uses a v6 nexthop from a nexthop group.
Allow the kernel to properly send the nexthop as v6 via the RTA_VIA
attribute.
Broken behavior:
$ ip nexthop add via fe80::9 dev eth0
$ ip nexthop show
id 1 via fe80::9 dev eth0 scope link
$ ip route add 4.5.6.7/32 nhid 1
$ ip route show
default via 10.0.2.2 dev eth0
4.5.6.7 nhid 1 via 254.128.0.0 dev eth0
10.0.2.0/24 dev eth0 proto kernel scope link src 10.0.2.15
$
Fixed behavior:
$ ip nexthop add via fe80::9 dev eth0
$ ip nexthop show
id 1 via fe80::9 dev eth0 scope link
$ ip route add 4.5.6.7/32 nhid 1
$ ip route show
default via 10.0.2.2 dev eth0
4.5.6.7 nhid 1 via inet6 fe80::9 dev eth0
10.0.2.0/24 dev eth0 proto kernel scope link src 10.0.2.15
$
v2, v3: Addresses code review comments from David Ahern
Fixes: dcb1ecb50e (“ipv4: Prepare for fib6_nh from a nexthop object”)
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEmvEkXzgOfc881GuFWsYho5HknSAFAl1vrJITHG1rbEBwZW5n
dXRyb25peC5kZQAKCRBaxiGjkeSdIC8BB/98XcWiaInD+SM6UjD2dVd1r0zhPKJS
WBK58G81+op3YP4DY8Iy+C24uZBlSlutVGoD/PIrZF39xXsnOtJuMVHC4LvtdADC
30uI/61JQNEjuX2AiTFudqDvYjZZKZ28HLqEnO2pWk3dMVL3+fkS3i7VQR7KJ/Gr
BYM6EzCdkbuWW/zsAVbKLJ8NswVmcdjP7eSK+exKppoWMtgCglZw1X6iP5YXDnbK
h3dGs687u8RfUra7j7vgnJzyQU4draMPsabaLDT5qw1PgYQ3k8MTVMBlULR0+HHO
qkBqumRwfOxay0z0XOgRuWrICKTH/b0SRLp3H53ZyfDo6+4TC9KGHRgX
=gwfZ
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-5.4-20190904' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2019-09-04 j1939
this is a pull request for net-next/master consisting of 21 patches.
the first 12 patches are by me and target the CAN core infrastructure.
They clean up the names of variables , structs and struct members,
convert can_rx_register() to use max() instead of open coding it and
remove unneeded code from the can_pernet_exit() callback.
The next three patches are also by me and they introduce and make use of
the CAN midlayer private structure. It is used to hold protocol specific
per device data structures.
The next patch is by Oleksij Rempel, switches the
&net->can.rcvlists_lock from a spin_lock() to a spin_lock_bh(), so that
it can be used from NAPI (soft IRQ) context.
The next 4 patches are by Kurt Van Dijck, he first updates his email
address via mailmap and then extends sockaddr_can to include j1939
members.
The final patch is the collective effort of many entities (The j1939
authors: Oliver Hartkopp, Bastian Stender, Elenita Hinds, kbuild test
robot, Kurt Van Dijck, Maxime Jayat, Robin van der Gracht, Oleksij
Rempel, Marc Kleine-Budde). It adds support of SAE J1939 protocol to the
CAN networking stack.
SAE J1939 is the vehicle bus recommended practice used for communication
and diagnostics among vehicle components. Originating in the car and
heavy-duty truck industry in the United States, it is now widely used in
other parts of the world.
P.S.: This pull request doesn't invalidate my last pull request:
"pull-request: can-next 2019-09-03".
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
TLS code has a number of #ifdefs which make the code a little
harder to follow. Recent fixes removed the ifdef around the
TLS_HW define, so we can switch to the often used pattern
of defining tls_device functions as empty static inlines
in the header when CONFIG_TLS_DEVICE=n.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we already have the pointer to the full original sk_proto
stored use that instead of storing all individual callback
pointers as well.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IN_MULTICAST's primary intent is as a uapi macro.
Elsewhere in the kernel we use ipv4_is_multicast consistently.
This patch unifies linux's multicast checks to use that function
rather than this macro.
Signed-off-by: Dave Taht <dave.taht@gmail.com>
Reviewed-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current tag set is still rather small and needs a couple
more tags to help with ASIC identification and to have a
more generic FW version.
Cc: Jiri Pirko <jiri@resnulli.us>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch improves the code reability by removing the redundant "can_"
prefix from the members of struct netns_can (as the struct netns_can itself
is the member "can" of the struct net.)
The conversion is done with:
sed -i \
-e "s/struct can_dev_rcv_lists \*can_rx_alldev_list;/struct can_dev_rcv_lists *rx_alldev_list;/" \
-e "s/spinlock_t can_rcvlists_lock;/spinlock_t rcvlists_lock;/" \
-e "s/struct timer_list can_stattimer;/struct timer_list stattimer; /" \
-e "s/can\.can_rx_alldev_list/can.rx_alldev_list/g" \
-e "s/can\.can_rcvlists_lock/can.rcvlists_lock/g" \
-e "s/can\.can_stattimer/can.stattimer/g" \
include/net/netns/can.h \
net/can/*.[ch]
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch gives the members of the struct netns_can that are holding
the statistics a sensible name, by renaming struct netns_can::can_stats
into struct netns_can::pkg_stats and struct netns_can::can_pstats into
struct netns_can::rcv_lists_stats.
The conversion is done with:
sed -i \
-e "s:\(struct[^*]*\*\)can_stats;.*:\1pkg_stats;:" \
-e "s:\(struct[^*]*\*\)can_pstats;.*:\1rcv_lists_stats;:" \
-e "s/can\.can_stats/can.pkg_stats/g" \
-e "s/can\.can_pstats/can.rcv_lists_stats/g" \
net/can/*.[ch] \
include/net/netns/can.h
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch renames both "struct s_stats" and "struct s_pstats", to
"struct can_pkg_stats" and "struct can_rcv_lists_stats" to better
reflect their meaning and improve code readability.
The conversion is done with:
sed -i \
-e "s/struct s_stats/struct can_pkg_stats/g" \
-e "s/struct s_pstats/struct can_rcv_lists_stats/g" \
net/can/*.[ch] \
include/net/netns/can.h
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds the infrastructure needed for the stateful object update
support.
Signed-off-by: Fernando Fernandez Mancera <ffmancera@riseup.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Devlink port index attribute is returned to users as u32 through
netlink response.
Change index data type from 'unsigned' to 'unsigned int' to avoid
below checkpatch.pl warning.
WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
81: FILE: include/net/devlink.h:81:
+ unsigned index;
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an application configures kernel TLS on top of a TCP socket, it's
now possible for inet_diag_handler() to collect information regarding the
protocol version, the cipher type and TX / RX configuration, in case
INET_DIAG_INFO is requested.
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
currently, only getsockopt(TCP_ULP) can be invoked to know if a ULP is on
top of a TCP socket. Extend idiag_get_aux() and idiag_get_aux_size(),
introduced by commit b37e88407c ("inet_diag: allow protocols to provide
additional data"), to report the ULP name and other information that can
be made available by the ULP through optional functions.
Users having CAP_NET_ADMIN privileges will then be able to retrieve this
information through inet_diag_handler, if they specify INET_DIAG_INFO in
the request.
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to make sure context does not get freed while diag
code is interrogating it. Free struct tls_context with
kfree_rcu().
We add the __rcu annotation directly in icsk, and cast it
away in the datapath accessor. Presumably all ULPs will
do a similar thing.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"unlikely(IS_ERR_OR_NULL(x))" is excessive. IS_ERR_OR_NULL() already uses
unlikely() internally.
Signed-off-by: Denis Efremov <efremov@linux.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Joe Perches <joe@perches.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, addresses are chunk size aligned. This means, we are very
restricted in terms of where we can place chunk within the umem. For
example, if we have a chunk size of 2k, then our chunks can only be placed
at 0,2k,4k,6k,8k... and so on (ie. every 2k starting from 0).
This patch introduces the ability to use unaligned chunks. With these
changes, we are no longer bound to having to place chunks at a 2k (or
whatever your chunk size is) interval. Since we are no longer dealing with
aligned chunks, they can now cross page boundaries. Checks for page
contiguity have been added in order to keep track of which pages are
followed by a physically contiguous page.
Signed-off-by: Kevin Laatz <kevin.laatz@intel.com>
Signed-off-by: Ciara Loftus <ciara.loftus@intel.com>
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
This is useful for checking how much airtime is being used up by other
transmissions on the channel, e.g. by calculating (time_rx - time_bss_rx)
or (time_busy - time_bss_rx - time_tx)
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20190828102042.58016-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Action sample doesn't properly handle psample_group pointer in overwrite
case. Following issues need to be fixed:
- In tcf_sample_init() function RCU_INIT_POINTER() is used to set
s->psample_group, even though we neither setting the pointer to NULL, nor
preventing concurrent readers from accessing the pointer in some way.
Use rcu_swap_protected() instead to safely reset the pointer.
- Old value of s->psample_group is not released or deallocated in any way,
which results resource leak. Use psample_group_put() on non-NULL value
obtained with rcu_swap_protected().
- The function psample_group_put() that released reference to struct
psample_group pointed by rcu-pointer s->psample_group doesn't respect rcu
grace period when deallocating it. Extend struct psample_group with rcu
head and use kfree_rcu when freeing it.
Fixes: 5c5670fae4 ("net/sched: Introduce sample tc action")
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove two holes on 64bit arches, to bring the size
to one cache line exactly.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to add ecn flag for both netns_sctp and sctp_endpoint,
net->sctp.ecn_enable is set 1 by default, and ep->ecn_enable will
be initialized with net->sctp.ecn_enable.
asoc->peer.ecn_capable will be set during negotiation only when
ep->ecn_enable is set on both sides.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bitmap operations were introduced to simplify the switch drivers
in the future, since most of them could implement the common VLAN and
MDB operations (add, del, dump) with simple functions taking all target
ports at once, and thus limiting the number of hardware accesses.
Programming an MDB or VLAN this way in a single operation would clearly
simplify the drivers a lot but would require a new get-set interface
in DSA. The usage of such bitmap from the stack also raised concerned
in the past, leading to the dynamic allocation of a new ds->_bitmap
member in the dsa_switch structure. So let's get rid of them for now.
This commit nicely wraps the ds->ops->port_{mdb,vlan}_{prepare,add}
switch operations into new dsa_switch_{mdb,vlan}_{prepare,add}
variants not using any bitmap argument anymore.
New dsa_switch_{mdb,vlan}_match helpers have been introduced to make
clear which local port of a switch must be programmed with the target
object. While the targeted user port is an obvious candidate, the
DSA links must also be programmed, as well as the CPU port for VLANs.
While at it, also remove local variables that are only used once.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The net pointer in struct xt_tgdtor_param is not explicitly
initialized therefore is still NULL when dereferencing it.
So we have to find a way to pass the correct net pointer to
ipt_destroy_target().
The best way I find is just saving the net pointer inside the per
netns struct tcf_idrinfo, which could make this patch smaller.
Fixes: 0c66dc1ea3 ("netfilter: conntrack: register hooks in netns when needed by ruleset")
Reported-and-tested-by: itugrok@yahoo.com
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements the delete operation from the ruleset.
It implements a new delete() function in nft_set_rhash. It is simpler
to use than the already existing remove(), because it only takes the set
and the key as arguments, whereas remove() expects a full
nft_set_elem structure.
Signed-off-by: Ander Juaristi <a@juaristi.eus>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
In order to remove dependency on rtnl lock, modify tc_setup_flow_action()
to copy tunnel info, instead of just saving pointer to tunnel_key action
tunnel info. This is necessary to prevent concurrent action overwrite from
releasing tunnel info while it is being used by rtnl-unlocked driver.
Implement helper tcf_tunnel_info_copy() that is used to copy tunnel info
with all its options to dynamically allocated memory block. Modify
tc_cleanup_flow_action() to free dynamically allocated tunnel info.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to remove dependency on rtnl lock when calling hardware offload
API, take reference to action mirred dev when initializing flow_action
structure in tc_setup_flow_action(). Implement function
tc_cleanup_flow_action(), use it to release the device after hardware
offload API is done using it.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to allow using new flow_action infrastructure from unlocked
classifiers, modify tc_setup_flow_action() to accept new 'rtnl_held'
argument. Take rtnl lock before accessing tc_action data. This is necessary
to protect from concurrent action replace.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend struct flow_block_offload with "unlocked_driver_cb" flag to allow
registering and unregistering block hardware offload callbacks that do not
require caller to hold rtnl lock. Extend tcf_block with additional
lockeddevcnt counter that is incremented for each non-unlocked driver
callback attached to device. This counter is necessary to conditionally
obtain rtnl lock before calling hardware callbacks in following patches.
Register mlx5 tc block offload callbacks as "unlocked".
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To remove dependency on rtnl lock, extend classifier ops with new
ops->hw_add() and ops->hw_del() callbacks. Call them from cls API while
holding cb_lock every time filter if successfully added to or deleted from
hardware.
Implement the new API in flower classifier. Use it to manage hw_filters
list under cb_lock protection, instead of relying on rtnl lock to
synchronize with concurrent fl_reoffload() call.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without rtnl lock protection filters can no longer safely manage block
offloads counter themselves. Refactor cls API to protect block offloadcnt
with tcf_block->cb_lock that is already used to protect driver callback
list and nooffloaddevcnt counter. The counter can be modified by concurrent
tasks by new functions that execute block callbacks (which is safe with
previous patch that changed its type to atomic_t), however, block
bind/unbind code that checks the counter value takes cb_lock in write mode
to exclude any concurrent modifications. This approach prevents race
conditions between bind/unbind and callback execution code but allows for
concurrency for tc rule update path.
Move block offload counter, filter in hardware counter and filter flags
management from classifiers into cls hardware offloads API. Make functions
tcf_block_offload_{inc|dec}() and tc_cls_offload_cnt_update() to be cls API
private. Implement following new cls API to be used instead:
tc_setup_cb_add() - non-destructive filter add. If filter that wasn't
already in hardware is successfully offloaded, increment block offloads
counter, set filter in hardware counter and flag. On failure, previously
offloaded filter is considered to be intact and offloads counter is not
decremented.
tc_setup_cb_replace() - destructive filter replace. Release existing
filter block offload counter and reset its in hardware counter and flag.
Set new filter in hardware counter and flag. On failure, previously
offloaded filter is considered to be destroyed and offload counter is
decremented.
tc_setup_cb_destroy() - filter destroy. Unconditionally decrement block
offloads counter.
tc_setup_cb_reoffload() - reoffload filter to single cb. Execute cb() and
call tc_cls_offload_cnt_update() if cb() didn't return an error.
Refactor all offload-capable classifiers to atomically offload filters to
hardware, change block offload counter, and set filter in hardware counter
and flag by means of the new cls API functions.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a preparation for running proto ops functions without rtnl lock, change
offload counter type to atomic. This is necessary to allow updating the
counter by multiple concurrent users when offloading filters to hardware
from unlocked classifiers.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to remove dependency on rtnl lock, extend tcf_block with 'cb_lock'
rwsem and use it to protect flow_block->cb_list and related counters from
concurrent modification. The lock is taken in read mode for read-only
traversal of cb_list in tc_setup_cb_call() and write mode in all other
cases. This approach ensures that:
- cb_list is not changed concurrently while filters is being offloaded on
block.
- block->nooffloaddevcnt is checked while holding the lock in read mode,
but is only changed by bind/unbind code when holding the cb_lock in write
mode to prevent concurrent modification.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce new helper functions to load/store 64-bit values onto/from
registers:
- nft_reg_store64
- nft_reg_load64
This commit also re-orders all these helpers from smallest to largest
target bit size.
Signed-off-by: Ander Juaristi <a@juaristi.eus>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Donald reported this sequence:
ip next add id 1 blackhole
ip next add id 2 blackhole
ip ro add 1.1.1.1/32 nhid 1
ip ro add 1.1.1.2/32 nhid 2
would cause a crash. Backtrace is:
[ 151.302790] general protection fault: 0000 [#1] SMP DEBUG_PAGEALLOC KASAN PTI
[ 151.304043] CPU: 1 PID: 277 Comm: ip Not tainted 5.3.0-rc5+ #37
[ 151.305078] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.11.1-1 04/01/2014
[ 151.306526] RIP: 0010:fib_add_nexthop+0x8b/0x2aa
[ 151.307343] Code: 35 f7 81 48 8d 14 01 c7 02 f1 f1 f1 f1 c7 42 04 01 f4 f4 f4 48 89 f2 48 c1 ea 03 65 48 8b 0c 25 28 00 00 00 48 89 4d d0 31 c9 <80> 3c 02 00 74 08 48 89 f7 e8 1a e8 53 ff be 08 00 00 00 4c 89 e7
[ 151.310549] RSP: 0018:ffff888116c27340 EFLAGS: 00010246
[ 151.311469] RAX: dffffc0000000000 RBX: ffff8881154ece00 RCX: 0000000000000000
[ 151.312713] RDX: 0000000000000004 RSI: 0000000000000020 RDI: ffff888115649b40
[ 151.313968] RBP: ffff888116c273d8 R08: ffffed10221e3757 R09: ffff888110f1bab8
[ 151.315212] R10: 0000000000000001 R11: ffff888110f1bab3 R12: ffff888115649b40
[ 151.316456] R13: 0000000000000020 R14: ffff888116c273b0 R15: ffff888115649b40
[ 151.317707] FS: 00007f60b4d8d800(0000) GS:ffff88811ac00000(0000) knlGS:0000000000000000
[ 151.319113] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 151.320119] CR2: 0000555671ffdc00 CR3: 00000001136ba005 CR4: 0000000000020ee0
[ 151.321367] Call Trace:
[ 151.321820] ? fib_nexthop_info+0x635/0x635
[ 151.322572] fib_dump_info+0xaa4/0xde0
[ 151.323247] ? fib_create_info+0x2431/0x2431
[ 151.324008] ? napi_alloc_frag+0x2a/0x2a
[ 151.324711] rtmsg_fib+0x2c4/0x3be
[ 151.325339] fib_table_insert+0xe2f/0xeee
...
fib_dump_info incorrectly has nhs = 0 for blackhole nexthops, so it
believes the nexthop object is a multipath group (nhs != 1) and ends
up down the nexthop_mpath_fill_node() path which is wrong for a
blackhole.
The blackhole check in nexthop_num_path is leftover from early days
of the blackhole implementation which did not initialize the device.
In the end the design was simpler (fewer special case checks) to set
the device to loopback in nh_info, so the check in nexthop_num_path
should have been removed.
Fixes: 430a049190 ("nexthop: Add support for nexthop groups")
Reported-by: Donald Sharp <sharpd@cumulusnetworks.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An excerpt from netlink(7) man page,
In multipart messages (multiple nlmsghdr headers with associated payload
in one byte stream) the first and all following headers have the
NLM_F_MULTI flag set, except for the last header which has the type
NLMSG_DONE.
but, after (ee28906) there is a missing NLM_F_MULTI flag in the middle of a
FIB dump. The result is user space applications following above man page
excerpt may get confused and may stop parsing msg believing something went
wrong.
In the golang netlink lib [0] the library logic stops parsing believing the
message is not a multipart message. Found this running Cilium[1] against
net-next while adding a feature to auto-detect routes. I noticed with
multiple route tables we no longer could detect the default routes on net
tree kernels because the library logic was not returning them.
Fix this by handling the fib_dump_info_fnhe() case the same way the
fib_dump_info() handles it by passing the flags argument through the
call chain and adding a flags argument to rt_fill_info().
Tested with Cilium stack and auto-detection of routes works again. Also
annotated libs to dump netlink msgs and inspected NLM_F_MULTI and
NLMSG_DONE flags look correct after this.
Note: In inet_rtm_getroute() pass rt_fill_info() '0' for flags the same
as is done for fib_dump_info() so this looks correct to me.
[0] https://github.com/vishvananda/netlink/
[1] https://github.com/cilium/
Fixes: ee28906fd7 ("ipv4: Dump route exceptions if requested")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
