Given a function, get_frame_info() analyzes its instructions
to figure out frame size and return address. get_frame_info()
works as follows:
1. analyze up to 128 instructions if the function size is unknown
2. search for 'addiu/daddiu sp,sp,-immed' for frame size
3. search for 'sw ra,offset(sp)' for return address
4. end search when it sees jr/jal/jalr
This leads to an issue when the given function is a sibling
call, example shown as follows.
801ca110 <schedule>:
801ca110: 8f820000 lw v0,0(gp)
801ca114: 8c420000 lw v0,0(v0)
801ca118: 080726f0 j 801c9bc0 <__schedule>
801ca11c: 00000000 nop
801ca120 <io_schedule>:
801ca120: 27bdffe8 addiu sp,sp,-24
801ca124: 3c028022 lui v0,0x8022
801ca128: afbf0014 sw ra,20(sp)
In this case, get_frame_info() cannot properly detect schedule's
frame info, and eventually returns io_schedule's instead.
This patch adds 'j' to the end search condition to workaround
sibling call cases.
Signed-off-by: Tony Wu <tung7970@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5236/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
As reported:
This problem was discovered when doing BGP traffic with the TCP MD5 option
activated, where the following call chain caused a crash:
* tcp_v4_rcv
* tcp_v4_timewait_ack
* tcp_v4_send_ack -> follow stack variable rep.th
* tcp_v4_md5_hash_hdr
* tcp_md5_hash_header
* sg_init_one
* sg_set_buf
* virt_to_page
I noticed that tcp_v4_send_reset uses a similar stack variable and
also calls tcp_v4_md5_hash_hdr, so it has the same problem.
The networking core can indirectly call virt_to_phys() on stack
addresses, if this is done from PID 0, the stack will usually be in
CKSEG0, so virt_to_phys() needs to work there as well
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Cc: Jiang Liu <liuj97@gmail.com>
Cc: eunb.song@samsung.com
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/5220/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch fixes crash_dump.c build error. Build error logs are as follow.
arch/mips/kernel/crash_dump.c: In function 'kdump_buf_page_init':
arch/mips/kernel/crash_dump.c:67: error: implicit declaration of function 'kmalloc'
arch/mips/kernel/crash_dump.c:67: error: assignment makes pointer from integer without a cast
Signed-off-by: EunBong Song <eunb.song@samsung.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/5238/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This reverts commit d532f3d267.
The original commit has several problems:
1) Doesn't work with 64-bit kernels.
2) Calls TLBMISS_HANDLER_SETUP() before the code is generated.
3) Calls TLBMISS_HANDLER_SETUP() twice in per_cpu_trap_init() when
only one call is needed.
[ralf@linux-mips.org: Also revert the bits of the ASID patch which were
hidden in the KVM merge.]
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: "Steven J. Hill" <Steven.Hill@imgtec.com>
Cc: David Daney <david.daney@cavium.com>
Patchwork: https://patchwork.linux-mips.org/patch/5242/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pull stray syscall bits from Al Viro:
"Several syscall-related commits that were missing from the original"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal:
switch compat_sys_sysctl to COMPAT_SYSCALL_DEFINE
unicore32: just use mmap_pgoff()...
unify compat fanotify_mark(2), switch to COMPAT_SYSCALL_DEFINE
x86, vm86: fix VM86 syscalls: use SYSCALL_DEFINEx(...)
Pull MIPS updates from Ralf Baechle:
- More work on DT support for various platforms
- Various fixes that were to late to make it straight into 3.9
- Improved platform support, in particular the Netlogic XLR and
BCM63xx, and the SEAD3 and Malta eval boards.
- Support for several Ralink SOC families.
- Complete support for the microMIPS ASE which basically reencodes the
existing MIPS32/MIPS64 ISA to use non-constant size instructions.
- Some fallout from LTO work which remove old cruft and will generally
make the MIPS kernel easier to maintain and resistant to compiler
optimization, even in absence of LTO.
- KVM support. While MIPS has announced hardware virtualization
extensions this KVM extension uses trap and emulate mode for
virtualization of MIPS32. More KVM work to add support for VZ
hardware virtualizaiton extensions and MIPS64 will probably already
be merged for 3.11.
Most of this has been sitting in -next for a long time. All defconfigs
have been build or run time tested except three for which fixes are being
sent by other maintainers.
Semantic conflict with kvm updates done as per Ralf
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (118 commits)
MIPS: Add new GIC clockevent driver.
MIPS: Formatting clean-ups for clocksources.
MIPS: Refactor GIC clocksource code.
MIPS: Move 'gic_frequency' to common location.
MIPS: Move 'gic_present' to common location.
MIPS: MIPS16e: Add unaligned access support.
MIPS: MIPS16e: Support handling of delay slots.
MIPS: MIPS16e: Add instruction formats.
MIPS: microMIPS: Optimise 'strnlen' core library function.
MIPS: microMIPS: Optimise 'strlen' core library function.
MIPS: microMIPS: Optimise 'strncpy' core library function.
MIPS: microMIPS: Optimise 'memset' core library function.
MIPS: microMIPS: Add configuration option for microMIPS kernel.
MIPS: microMIPS: Disable LL/SC and fix linker bug.
MIPS: microMIPS: Add vdso support.
MIPS: microMIPS: Add unaligned access support.
MIPS: microMIPS: Support handling of delay slots.
MIPS: microMIPS: Add support for exception handling.
MIPS: microMIPS: Floating point support.
MIPS: microMIPS: Fix macro naming in micro-assembler.
...
GENERIC_GPIO now synonymous with GPIOLIB. There are no longer any valid
cases for enableing GENERIC_GPIO without GPIOLIB, even though it is
possible to do so which has been causing confusion and breakage. This
branch does the work to completely eliminate GENERIC_GPIO.
However, it is not trivial to just create a branch to remove it. Over
the course of the v3.9 cycle more code referencing GENERIC_GPIO has been
added to linux-next that conflicts with this branch. The following must
be done to resolve the conflicts when merging this branch into mainline:
* "git grep CONFIG_GENERIC_GPIO" should return 0 hits. Matches should be
replaced with CONFIG_GPIOLIB
* "git grep '\bGENERIC_GPIO\b'" should return 1 hit in the Chinese
documentation.
* Selectors of GENERIC_GPIO should be turned into selectors of GPIOLIB
* definitions of the option in architecture Kconfig code should be deleted.
Stephen has 3 merge fixup patches[1] that do the above. They are currently
applicable on mainline as of May 2nd.
[1] http://www.mail-archive.com/linux-kernel@vger.kernel.org/msg428056.html
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJRifUnAAoJEEFnBt12D9kBs2YP/0U6+ia+xYvkVaJc28PDVIzn
OReZNcJOYU8D5voxz0voaRD0EdcPwjbMu9Kp9aXMHlk4VxevF+8jCc/us0bIjtO1
VcB5VmSCIhMhxdnBlum11Mk7Vr5MCweyl9NBsypnPt8cl4obMBZHf2yzoodFktNb
wtyYlOb6FALtc6iDbOO6dG3w9F7FAOLvskUFzdv89m8mupTsBu9jw9NqFDbJHOex
rxq0Sdd+kWF/nkJVcV5Y6jIdletRlhpipefMJ9diexreHvwqh+c4kJEYZaXgB5+m
ha95cPbReK1d+RqzM3A8d4irzSVSmq4k7ijI6QkFOr48+AH7XsgKv5so885LKzMN
IIXg2Phm9i0H8+ecEvhcc4oIYBHJiEKK54Y0qUD9dqbFoDGPTCSqMHdSSMbpAY+J
bIIXlVzj1En3PPNUJLPt8q8Qz6WxCT9mDST3QSGYnD4o90HT+1R9j92RxGL6McOq
rUOyJDwmzFvpBvKK4raGdOU435M+ps2NPKKNIRaIGQPPY9rM1kN4YqvhXukEsC9L
3a3+3cQLh7iKxBHncxeQsJfethP1CPkJnzvF9r+ZZLf2rcPH4pbQIE2uO0XnX/nd
5/DKi0nGgAJ//GMMzdo3RiOA5zGFjIZ/KMvfhQldpP6qFJRhqdGi6FPlAcwr1z1n
YnCByPwwlvfC4LTXFOGL
=xodc
-----END PGP SIGNATURE-----
Merge tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux
Pull removal of GENERIC_GPIO from Grant Likely:
"GENERIC_GPIO now synonymous with GPIOLIB. There are no longer any
valid cases for enableing GENERIC_GPIO without GPIOLIB, even though it
is possible to do so which has been causing confusion and breakage.
This branch does the work to completely eliminate GENERIC_GPIO."
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux:
gpio: update gpio Chinese documentation
Remove GENERIC_GPIO config option
Convert selectors of GENERIC_GPIO to GPIOLIB
blackfin: force use of gpiolib
m68k: coldfire: use gpiolib
mips: pnx833x: remove requirement for GENERIC_GPIO
openrisc: default GENERIC_GPIO to false
avr32: default GENERIC_GPIO to false
xtensa: remove explicit selection of GENERIC_GPIO
sh: replace CONFIG_GENERIC_GPIO by CONFIG_GPIOLIB
powerpc: remove redundant GENERIC_GPIO selection
unicore32: default GENERIC_GPIO to false
unicore32: remove unneeded select GENERIC_GPIO
arm: plat-orion: use GPIO driver on CONFIG_GPIOLIB
arm: remove redundant GENERIC_GPIO selection
mips: alchemy: require gpiolib
mips: txx9: change GENERIC_GPIO to GPIOLIB
mips: loongson: use GPIO driver on CONFIG_GPIOLIB
mips: remove redundant GENERIC_GPIO select
Add new clockevent driver that uses the counter present on the MIPS
Global Interrupt Controller.
Signed-off-by: Raghu Gandham <Raghu.Gandham@imgtec.com>
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Reorganize some of the GIC clocksource driver code. Below is a list of
the various changes.
* No longer select CSRC_GIC by default for Malta platform.
* Limit choice for either the GIC or R4K clocksource, not both.
* Change location in Makefile.
* Created new 'gic_read_count' function in common 'irq-gic.c' file.
* Change 'git_hpt_read' function in 'csrc-gic.c' to use new function.
* Surround GIC specific code in Malta platform code with #ifdef's.
* Only initialize the GIC clocksource if it was selected. Original
code called it unconditionally if a GIC was found.
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Move the global variable 'gic_frequency' to be defined in the file
'arch/mips/kernel/irq-gic.c' instead of defining it individually
for each platform making use of the GIC. Also change the type to
be an unsigned integer instead of signed.
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Move the global variable 'gic_present' to be defined in the file
'arch/mips/kernel/irq-gic.c' instead of defining it individually
for each platform making use of the GIC. Also change the type to
be an unsigned integer instead of signed.
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Add logic needed to handle unaligned accesses in MIPS16e mode.
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Add structures for all the MIPS16e instructions. Also add the
enumerations for all the bit fields for opcodes, functions, etc.
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Optimise 'strnlen' to use microMIPS instructions and/or optimisations
for binary size reduction. When the microMIPS ISA is not being used,
the library function compiles to the original binary code.
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Optimise 'strlen' to use microMIPS instructions and/or optimisations
for binary size reduction. When the microMIPS ISA is not being used,
the library function compiles to the original binary code.
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Optimise 'strncpy' to use microMIPS instructions and/or optimisations
for binary size reduction. When the microMIPS ISA is not being used,
the library function compiles to the original binary code.
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Optimise 'memset' to use microMIPS instructions and/or optimisations
for binary size reduction. When the microMIPS ISA is not being used,
the library function compiles to the original binary code.
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
This adds the option to build the Linux kernel using only the
microMIPS ISA. The resulting kernel binary is, at a minimum,
20% smaller than using the MIPS32R2 ISA.
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Partially revert commit e0c14a260d66ba35935600d6435940a566fe806b
and turn off LL/SC when building a pure microMIPS kernel. This is
a temporary fix until the cmpxchg assembly macro functions are
re-written to not use the HI/LO registers in address calculations.
Also add .insn in selected user access functions which would
otherwise produce ISA mode jump incompatibilities. This is also a
temporary fix.
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Add logic needed to handle unaligned accesses in microMIPS mode.
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Add logic needed to properly calculate exceptions for delay slots
when in microMIPS mode.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
All exceptions must be taken in microMIPS mode, never in classic
MIPS mode or the kernel falls apart. A few NOP instructions are
used to maintain the correct alignment of microMIPS versions of
the exception vectors.
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Add logic needed to do floating point emulation in microMIPS mode.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Steven J. Hill <Steven. Hill@imgtec.com>
The macros did not properly take into account the ISA that
the kernel was being compiled with. A classic MIPS kernel
will have the standard 'uasm_i_##op' macro functions with
'MM_uasm_i_##op' macro functions for the microMIPS version.
A pure microMIPS kernel will have the standard macros with
'CL_uasm_i_##op' macro functions for the classic version.
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Jump or branch target addresses have the first bit set. The
original mask did not take this into account and will cause
a field overflow warning for the target address when a jump
immediate instruction is built.
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Currently, the following instructions are translated:
- CACHE (indexed)
- CACHE (va based): translated to a SYNCI, overkill on D-CACHE operations,
but still much faster than a trap.
- mfc0/mtc0: the virtual COP0 registers for the guest are implemented as
2-D array.
[COP#][SEL] and this is mapped into the guest kernel address space @ VA 0x0.
mfc0/mtc0 operations are transformed to load/stores.
Signed-off-by: Sanjay Lal <sanjayl@kymasys.com>
Cc: kvm@vger.kernel.org
Cc: linux-mips@linux-mips.org
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Changes for pure microMIPS cores to dynamically determine the ASID
size at boot time.
Includes bug fix https://patchwork.linux-mips.org/patch/5230/
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Original patch by Ralf Baechle and removed by Harold Koerfgen
with commit f67e4ffc79905482c3b9b8c8dd65197bac7eb508. This
allows for more generic kernels since the size of the ASID
and corresponding masks can be determined at run-time. This
patch is also required for the new Aptiv cores and has been
tested on Malta and Malta Aptiv platforms.
[ralf@linux-mips.org: Added relevant part of fix
https://patchwork.linux-mips.org/patch/5213/]
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove 'arch/mips/include/asm/mips-boards/prom.h' and get rid of
all inclusions of it by Malta and SEAD-3 platforms.
[ralf@linux-mips.org: Fold in John Crispin <blogic@openwrt.org>'s "MIPS:
ar7 powertv build"].
[ralf@linux-mips.org: Fold in John Crispin <blogic@openwrt.org>'s "MIPS:
unbreak powertv build"].
[ralf@linux-mips.org: Test. Build. Your. Fscking. Code. Or...]
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Add parsing of the environment and command line variables passed to
the kernel to the firmware library.
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Add declaration of 'mips_scroll_message' and 'mips_display_message'
to the common generic header file for the MIPS Technologies Inc.
development boards.
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Setting the LED_CORE_SUSPENDRESUME flag causes the LED driver core to call
led_classdev_suspend/led_classdev_resume during suspend/resume. Since this is
exactly what the driver's custom suspend/resume callbacks do we can replace them
by setting the LED_CORE_SUSPENDRESUME flag.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
