Since the force restore logic will restore the CRTCs state one at a
time, it is possible that the state will be inconsistent until the whole
operation finishes. A call to intel_modeset_check_state() is done once
it's over, so don't check the state multiple times in between. This
regression was introduced in:
commit 7f27126ea3
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Wed Nov 5 14:26:06 2014 -0800
drm/i915: factor out compute_config from __intel_set_mode v3
v2: Rename check parameter to force_restore. (Matt)
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=94431
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Only bit 27 of SCRATCH1 and bit 6 of ROW_CHICKEN3 are allowed to be
set because of security-sensitive bits we don't want userspace to mess
with. On HSW hardware the whitelisted bits control whether atomic
read-modify-write operations are performed on L3 or on GTI, and when
set to L3 (which can be 10x-30x better performing than on GTI,
depending on the application) require great care to avoid a system
hang, so we currently program them to be handled on GTI by default.
Beignet can immediately start taking advantage of this change to
enable L3 atomics. Mesa should eventually switch to L3 atomics too,
but a number of non-trivial changes are still required so it will
continue using GTI atomics for now.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Reviewed-by: Zhigang Gong <zhigang.gong@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
In some cases it might be unnecessary or dangerous to give userspace
the right to write arbitrary values to some register, even though it
might be desirable to give it control of some of its bits. This patch
extends the register whitelist entries to contain a mask/value pair in
addition to the register offset. For registers with non-zero mask,
any LRM writes and LRI writes where the bits of the immediate given by
the mask don't match the specified value will be rejected.
This will be used in my next patch to grant userspace partial write
access to some sensitive registers.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Reviewed-by: Zhigang Gong <zhigang.gong@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Until now the software command checker assumed that commands could
read or write at most a single register per packet. This is not
necessarily the case, MI_LOAD_REGISTER_IMM expects a variable-length
list of offset/value pairs and writes them in sequence. The previous
code would only check whether the first entry was valid, effectively
allowing userspace to write unrestricted registers of the MMIO space
by sending a multi-register write with a legal first register, with
potential security implications on Gen6 and 7 hardware.
Fix it by extending the drm_i915_cmd_descriptor table to represent
multi-register access and making validate_cmd() iterate for all
register offsets present in the command packet.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Reviewed-by: Zhigang Gong <zhigang.gong@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Apparently we can have requests even if though the active list is empty,
so do the request retirement regardless of whether there's anything
on the active list.
The way it happened here is that during suspend intel_ring_idle()
notices the olr hanging around and then proceeds to get rid of it by
adding a request. However since there was nothing on the active lists
i915_gem_retire_requests() didn't clean those up, and so the idle work
never runs, and we leave the GPU "busy" during suspend resulting in a
WARN later.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
04 is the minor version. API version is ver1.
So let's follow same scheme used on published version at 01.org.
If really needed the minor version a follow-up updated will be
done. But for now we need to move fwd and unblock end users.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
We already set this limit for the GGTT.
This is a temporary patch until a full replacement of size_t variables
(inadequate in 32-bit kernel) is in place.
Regression from:
commit a4e0bedca6
Author: Michel Thierry <michel.thierry@intel.com>
Date: Wed Apr 8 12:13:35 2015 +0100
drm/i915: Use complete address space in true PPGTT
v2: Prettify code and explain why this is needed. (Chris)
v3: Don't hide the compilation warning in 32-bit. (Chris)
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With unified modeset and flip paths introduced recently when switching
to fbcon PSR was being disabled on fb_set_par path but re-enabled on
fb_pan_display one, causing missed screen updates and un unusable
console.
Regression introduced with:
commit bb54662350
Author: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Date: Tue Apr 21 17:13:13 2015 +0300
drm/i915: Unify modeset and flip paths of intel_crtc_set_config()
Cc: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Without this frontbuffer flip when enabling planes PSR got compromised
and wasn't being enabled waiting forever on the flush that never
arrived.
Another solution would to create a enable_cursor function and split this
frontbuffer flip among the different plane enable and disable functions.
But if necessary this can be done in a follow up work. For now let's
just fix the regression.
It was removed by:
commit 87d4300a7d
Author: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Date: Tue Apr 21 17:12:54 2015 +0300
drm/i915: Move intel_(pre_disable/post_enable)_primary to intel_display.c, and use it there.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This commit is the "sink CRC" version of:
commit 8c740dcea2
Author: Paulo Zanoni <paulo.r.zanoni@intel.com>
Date: Fri Oct 17 18:42:03 2014 -0300
drm/i915: disable IPS while getting the pipe CRCs.
For some unknown reason, when IPS gets enabled, the sink CRC changes.
Since hsw_enable_ips() doesn't really guarantee to enable IPS (it
depends on package C-states), we can't really predict if IPS is
enabled or disabled while running our CRC tests, so let's just
completely disable IPS while sink CRCs are being used.
If we find a way to make IPS not change the pipe CRC result, we may
want to fix IPS and then revert this patch (and 8c740dcea too). While
this doesn't happen, let's merge this patch, so the IGT tests relying
on sink CRCs can work properly.
This was discovered while developing a new IGT test, which will
probably be called kms_frontbuffer_tracking.
Testcase: igt/kms_frontbuffer_tracking (not on upstream IGT yet)
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It's totally broken, and since
commit d328c9d78d
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Fri Apr 10 16:22:37 2015 +0200
drm/i915: Select starting pipe bpp irrespective or the primary plane
the kernel will try to use it even for the common rgb888 framebuffers.
Ville has patches to fix it all up properly, but unfortunately they're
stuck in review limbo. And since the 4.2 feature cutoff has passed we
need to somehow handle this regression.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Paulo Zanoni <przanoni@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
chv_enable_pll() doesn't need to hold sb_lock for the entire duration of
the function. Drop the lock as soon as possible.
valleyview_set_cdclk() does a potential lock+unlock+lock+unlock cycle
with sb_lock. Grab the lock a few lines earlier so we can make do
with a single lock+unlock cycle always.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rename dpio_lock to sb_lock to inform the reader that its primary
purpose is to protect the sideband mailbox rather than some DPIO
state.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The primary plane frobbing was removed from the sprite code in
commit ecce87ea3a
Author: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Date: Tue Apr 21 17:12:50 2015 +0300
drm/i915: Remove implicitly disabling primary plane for now
but the intel_flush_primary_plane() calls were left behind. Replace them
with straight forward POSTING_READ() of the sprite surface address
register.
The other user of intel_flush_primary_plane() is g4x_disable_trickle_feed()
where we can just inline the steps directly.
This allows intel_flush_primary_plane() to be killed off.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Expecting CHV power wells to be just an extended versions of the VLV
power wells, a bunch of commented out power wells were added in
anticipation when Punit folks would implement it all. Turns out they
never did, and instead CHV has fewer power wells than VLV. Rip out all
the #if 0'ed junk that's not needed.
v2: Rename the "pipe-a" well to "display" to match VLV
Clarify the pipe A power well relationship to pipes B and C (Deepak)
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Not sure which LDO programming sequence delay should be used for the CHV
PHY, but the spec says that 600ns is "Used by default for initial
bringup", and the BIOS seems to use that, so let's do the same.
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
commit 53292cdb06 ("drm/i915: Workaround
to avoid lite restore with HEAD==TAIL") added a check for req0 != null
which is unnecessary.
The only way req0 could be null is if the list was empty, and this is
already addressed at the beginning of execlists_context_unqueue().
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In commit 1854d5ca0d
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Tue Apr 7 16:20:32 2015 +0100
drm/i915: Deminish contribution of wait-boosting from clients
we removed an atomic timer based check for allowing waitboosting and
moved it below the mutex taken during RPS. However, that mutex can be
held for long periods of time on Vallyview/Cherryview as communication
with the PCU is slow. As clients may frequently wait for results (e.g.
such as tranform feedback) we introduced contention between the client
and the RPS worker. We can take advantage of the RPS worker, by
switching the wait boost decision to use spin locks and defer the
actual reclocking to the worker.
Fixes a regression of up to 45% on Baytrail and Baswell!
v2 (Daniel):
- Use max_freq_softlimit instead of the not-yet-merged boost
frequency.
- Don't inject a fake irq into the boost work, instead treat
client_boost as just another legit waker.
v3: Drop the now unused mask (Chris).
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90112
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It was reported that this comment was confusing, and indeed it is.
v2: (one year later!) Add the range for the DRM_I915_* iotcl defines
(Daniel)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This reverts commit 118182e9d7.
It's causing too much trouble when compile-testing for non-i915 folks.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
As Daniel commented on
commit b7ffe1362c5f468b853223acc9268804aa92afc8
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Mon Apr 27 13:41:24 2015 +0100
drm/i915: Free RPS boosts for all laggards
it is better to be explicit when sharing hardcoded values such as
throttle/boost timeouts. Make it so!
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
After allocating from the slab cache, we then need to free the request
back into the slab cache upon error (and not call kfree as that leads
to eventual memory corruption).
Fixes regression from
commit efab6d8dd1
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Tue Apr 7 16:20:57 2015 +0100
drm/i915: Use a separate slab for requests
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There is a mplayer video failure reported with xv.
This is because there is a request to do both plane scaling
and colorkey. Because skl hw doesn't support plane scaling
and colorkey at the same time, request is failed which is expected
behavior.
To make xv operate, this patch allows colorkey continue to work
without using scaler. Then behavior would be similar to platforms
without plane scaler support.
Signed-off-by: Chandra Konduru <chandra.konduru@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90449
[danvet: change can_scale to bool as requested by Ville.]
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
GTT caching was disabled by default on gen8 due to not working with
big pages. Some information suggests that it got fixed, but still
GTT caching has been left disabled by default. Or could be it just
meant that the default was changed to off, and hence the problem
got solved.
Enable GTT caching in the hopes of some performance increase.
Whether or not the big pages issue has been fixed is irrelevant
at this stage since we don't use big pages.
This gives me a 1-2% improvement in xonotic on my BSW. Haven't tried
BDW, but supposedly it has larger TLBs so might not benefit as much.
On HSW GTT caching is enabled by default.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
GEN8_L3SQCREG1 isn't saved in the context (verified by going through
a context dump), and so we shouldn't be using the ring w/a code to
initialize it. Also Bspec explicitly talks about MMIO and writing it
with the CPU.
Additionally there's another w/a WaTempDisableDOPClkGating:bdw which
tells us to disable DOP clock gating around the GEN8_L3SQCREG1 write
to make sure everyone notices the change. So let's do that as well.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We're not using ilk_init_lp_watermarks() on BDW for some reason.
Probably due to the BDW patches and the relevant WM patches landing
roughlly at the same time. Fix it up.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Bspec says we should disable the FDI RX/TX before disabling the PCH
ports. Do so.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Follow the BSpec sequence for the CRT port as well on PCH platforms,
ie. disable the pipe before the port.
Didn't bother looking at DDI in detail yet, so leave that one be even
though the CRT is a PCH port there.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
While at it also remove the redundant/unneeded w/a like done for hdmi
already.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Mention that this also removes the unneeded w/a, as suggested
by Jesse.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
BSpec says we should disable all ports after the pipe on PCH
platforms. Do so. Fixes a pipe off timeout on ILK now caused by
the transcoder B workaround.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently the IBX transcoder B workarounds are not working correctly.
Well, the HDMI one seems to be working somewhat, but the DP one is
definitely busted.
After a bit of experimentation it looks like the best way to make this
work is first disable the port on transcoder B, and then re-enable it
transcoder A, and immediately disable it again.
We can also clean up the code by noting that we can't be called without
a valid crtc. And also note that port A on ILK does not need the
workaround, so let's check for that one too.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On IBX the SDVO/HDMI register write may be masked when enabling the
port, so it may need to written twice. The HDMI code does this, but
the SDVO code does not. Add the workaround to the SDVO code as well.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently we're always enabling enhanced framing on CPT even if the sink
doesn't support it. Fix this up by actaully looking at what the sink
tells us.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Define a TRANS_DP_PIPE_TO_PORT() to make the CPT DP .get_hw_state()
pipe readout neater.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
intel_dp.c is a mess with all the checks for different
platform/PCH variants and ports. Try to clean it up by recognizing
the following facts:
- IVB port A, and CPT port B/C/D are always the special cases
- VLV/CHV don't have port A
- Using the same kind of logic everywhere makes things much easier to
parse
So let's move the IVB port A and PCH port B/C/D checks to be done first,
and let the other cases fall through, and always check for these things
using the same logic.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
IBX can have problems with the first write to the port register getting
masked when enabling the port. We are trying to apply the workaround
also when disabling the port where it's not needed, and we also try
to apply it for CPT/PPT as well which don't need it. Just kill it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Resolve conflict with the remove CHV if block.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The IBX 12bpc port enable toggle is only relevant when enabling
the port, not when disabling it. Also this code doesn't actually
toggle anything, and essentially just writes the port register
one extra time. Furthermore CPT/PPT don't need such workarounds
and yet we include them. Just kill it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need to re-init the display hardware when going out of suspend. This
includes:
- Hooking the PCH to the reset logic
- Restoring CDCDLK
- Enabling the DDB power
Among those, only the CDCDLK one is a bit tricky. There's some
complexity in that:
- DPLL0 (which is the source for CDCLK) has two VCOs, each with a set
of supported frequencies. As eDP also uses DPLL0 for its link rate,
once DPLL0 is on, we restrict the possible eDP link rates the chosen
VCO.
- CDCLK also limits the bandwidth available to push pixels.
So, as a first step, this commit restore what the BIOS set, until I can
do more testing.
In case that's of interest for the reviewer, I've unit tested the
function that derives the decimal frequency field:
#include <stdio.h>
#include <stdint.h>
#include <assert.h>
#define ARRAY_SIZE(x) (sizeof(x) / sizeof(*(x)))
static const struct dpll_freq {
unsigned int freq;
unsigned int decimal;
} freqs[] = {
{ .freq = 308570, .decimal = 0b01001100111},
{ .freq = 337500, .decimal = 0b01010100001},
{ .freq = 432000, .decimal = 0b01101011110},
{ .freq = 450000, .decimal = 0b01110000010},
{ .freq = 540000, .decimal = 0b10000110110},
{ .freq = 617140, .decimal = 0b10011010000},
{ .freq = 675000, .decimal = 0b10101000100},
};
static void intbits(unsigned int v)
{
int i;
for(i = 10; i >= 0; i--)
putchar('0' + ((v >> i) & 1));
}
static unsigned int freq_decimal(unsigned int freq /* in kHz */)
{
return (freq - 1000) / 500;
}
static void test_freq(const struct dpll_freq *entry)
{
unsigned int decimal = freq_decimal(entry->freq);
printf("freq: %d, expected: ", entry->freq);
intbits(entry->decimal);
printf(", got: ");
intbits(decimal);
putchar('\n');
assert(decimal == entry->decimal);
}
int main(int argc, char **argv)
{
int i;
for (i = 0; i < ARRAY_SIZE(freqs); i++)
test_freq(&freqs[i]);
return 0;
}
v2:
- Rebase on top of -nightly
- Use (freq - 1000) / 500 for the decimal frequency (Ville)
- Fix setting the enable bit of HSW_NDE_RSTWRN_OPT (Ville)
- Rename skl_display_{resume,suspend} to skl_{init,uninit}_cdclk to
be consistent with the BXT code (Ville)
- Store boot CDCLK in ddi_pll_init (Ville)
- Merge dev_priv's skl_boot_cdclk into cdclk_freq
- Use LCPLL_PLL_LOCK instead of (1 << 30) (Ville)
- Replace various '0' by SKL_DPLL0 to be a bit more explicit that
we're programming DPLL0
- Busy poll the PCU before doing the frequency change. It takes about
3/4 cycles, each separated by 10us, to get the ACK from the CPU
(Ville)
v3:
- Restore dev_priv->skl_boot_cdclk, leaving unification with
dev_priv->cdclk_freq for a later patch (Daniel, Ville)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If the client stalls on a congested request, chosen to be 20ms old to
match throttling, allow the client a free RPS boost.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: s/rq/req/]
[danvet: s/0/NULL/ reported by 0-day build]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we have clients stalled waiting for requests, ignore the GPU if it
signals that it should downclock due to low load. This helps prevent
the automatic timeout from causing extremely long running batches from
taking even longer.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that we have internal clients, rather than faking a whole
drm_i915_file_private just for tracking RPS boosts, create a new struct
intel_rps_client and pass it along when waiting.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: s/rq/req/]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since we will often pageflip to an active surface, we will often have to
wait for the surface to be written before issuing the flip. Also we are
likely to wait on that surface in plenty of time before the vblank.
Since we have a mechanism for boosting when a flip misses the expected
vblank, curtain the number of times we RPS boost when simply waiting for
mmioflip.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: s/rq/req/]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ring switches can occur many times per frame, and are often out of
control, causing frequent RPS boosting for no practical benefit. Treat
the sw semaphore synchronisation as a separate client and only allow it
to boost once per busy/idle cycle.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: s/rq/req/]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This trims a little overhead from the common case of not needing to
synchronize between rings.
v2: execlists is special and likes to duplicate code.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently, we only track the last request globally across all engines.
This prevents us from issuing concurrent read requests on e.g. the RCS
and BCS engines (or more likely the render and media engines). Without
semaphores, we incur costly stalls as we synchronise between rings -
greatly impacting the current performance of Broadwell versus Haswell in
certain workloads (like video decode). With the introduction of
reference counted requests, it is much easier to track the last request
per ring, as well as the last global write request so that we can
optimise inter-engine read read requests (as well as better optimise
certain CPU waits).
v2: Fix inverted readonly condition for nonblocking waits.
v3: Handle non-continguous engine array after waits
v4: Rebase, tidy, rewrite ring list debugging
v5: Use obj->active as a bitfield, it looks cool
v6: Micro-optimise, mostly involving moving code around
v7: Fix retire-requests-upto for execlists (and multiple rq->ringbuf)
v8: Rebase
v9: Refactor i915_gem_object_sync() to allow the compiler to better
optimise it.
Benchmark: igt/gem_read_read_speed
hsw:gt3e (with semaphores):
Before: Time to read-read 1024k: 275.794µs
After: Time to read-read 1024k: 123.260µs
hsw:gt3e (w/o semaphores):
Before: Time to read-read 1024k: 230.433µs
After: Time to read-read 1024k: 124.593µs
bdw-u (w/o semaphores): Before After
Time to read-read 1x1: 26.274µs 10.350µs
Time to read-read 128x128: 40.097µs 21.366µs
Time to read-read 256x256: 77.087µs 42.608µs
Time to read-read 512x512: 281.999µs 181.155µs
Time to read-read 1024x1024: 1196.141µs 1118.223µs
Time to read-read 2048x2048: 5639.072µs 5225.837µs
Time to read-read 4096x4096: 22401.662µs 21137.067µs
Time to read-read 8192x8192: 89617.735µs 85637.681µs
Testcase: igt/gem_concurrent_blit (read-read and friends)
Cc: Lionel Landwerlin <lionel.g.landwerlin@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> [v8]
[danvet: s/\<rq\>/req/g]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The merged seqno->request conversion from John called request
variables req, but some (not all) of Chris' recent patches changed
those to just rq. We've had a lenghty (and inconclusive) discussion on
irc which is the more meaningful name with maybe at most a slight bias
towards req.
Given that the "don't change names without good reason to avoid
conflicts" rule applies, so lets go back to a req everywhere for
consistency. I'll sed any patches for which this will cause conflicts
before applying.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: John Harrison <John.C.Harrison@Intel.com>
[danvet: s/origina/merged/ as pointed out by Chris - the first
mass-conversion patch was from Chris, the merged one from John.]
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
v2:
- set the override disable flag too on stepping F0 (mika)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On B0 and C0 steppings the workaround enable bit would be overriden by
default, so the overriding must be disabled.
The WA was added in
commit 83a24979c4
Author: Nick Hoath <nicholas.hoath@intel.com>
Date: Fri Apr 10 13:12:26 2015 +0100
drm/i915/bxt: Add WaForceContextSaveRestoreNonCoherent
Spotted-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Our driver compiles clean (nowadays thanks to 0day) but for me, at least,
it would be beneficial if the compiler threw an error rather than a
warning when it found a piece of suspect code. (I use this to
compile-check patch series and want to break on the first compiler error
in order to fix the patch.)
v2: Kick off a new "Debugging" submenu for i915.ko
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Jani Nikula <jani.nikula@intel.com>
[danvet: Add "DRM i915" to the menu name as requested by Chris.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
