Currently if the kernel has the intel_iommu=on parameter set, on some
platforms removing the driver causes a system reboot. In initialization
we associate the control queue interrupts with the pf->hw_oicr_idx and
enable the interrupts by setting the CAUSE_ENA bit. The problem comes
on teardown because we are not clearing the CAUSE_ENA bit for the
control queues, but the vector at pf->hw_oicr_idx (miscellaneous
interrupt vector) gets disabled.
Fix this by clearing the CAUSE_ENA bit in the appropriate control queue
registers on when freeing the miscellaneous interrupt vector. Also,
move the call to ice_free_irq_msix_misc() to after ice_deinit_sw() in
ice_remove() because ice_deinit_sw() makes an AQ call, but
ice_free_irq_msix_misc() disables the miscellaneous vector and it's
associated interrupts.
Also, create two small helper functions to enable and disable the
control queue interrupts respectively.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When adding multiple VLANs to the same VSI, the ice_add_vlan code will
share the VSI list, so as not to create multiple unnecessary VSI lists.
Consider the following flow
ice_add_vlan(hw, <VSI 0 VID 7, VSI 0 VID 8, VSI 0 VID 9>)
Where we add three VLAN filters for VIDs 7, 8, and 9, all for VSI 0.
The ice_add_vlan will create a single vsi_list and share it among all
the filters.
Later, if we try to remove a VLAN,
ice_remove_vlan(hw, <VSI 0 VID 7>)
Then the removal code will update the vsi_list and remove VSI 0 from it.
But, since the vsi_list is shared, this breaks the list for the other
users who reference it. We actually even free the VSI list memory, and
may result in segmentation faults.
This is due to the way that VLAN rule share VSI lists with reference
counts, and is caused because we call ice_rem_update_vsi_list even when
the ref_cnt is greater than one.
To fix this, handle the case where ref_cnt is greater than one
separately. In this case, we need to remove the associated rule without
modifying the vsi_list, since it is currently being referenced by
another rule. Instead, we just need to decrement the VSI list ref_cnt.
The case for handling sharing of VSI lists with multiple VSIs is not
currently supported by this code. No such rules will be created today,
and this code will require changes if/when such code is added.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
struct ice_vsi_ctx has gotten large enough that function local declarations
of it on the stack are causing stack hogs. Fix that by allocating the
structs on heap. Cleanup some formatting issues in the code around these
changes and fix incorrect data type uses of returned functions in a couple
places.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
With sizeof(), it is preferable to use the variable of type <type> instead
of sizeof(<type>).
There are multiple places where a temporary variable is used to hold a
'size' value which is then used for a subsequent alloc/memset. Get rid
of the temporary variable by calculating size as part of the alloc/memset
statement.
Also remove unnecessary type-cast.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
VSI supported nodes are calculated in order to add the VSI parent or
intermediate nodes to the scheduler tree. If one of the node in below
layers (from VSI layer) has space to add the new VSI or intermediate node
above that layer then it's not required to continue the calculation further
for below layers.
Signed-off-by: Victor Raj <victor.raj@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently ICE_MAX_MTU subtracts only ETH_HLEN from max frame size and
adds ETH_FCS_LEN and VLAN_HLEN, which is not what was intended.
The ETH_HLEN + ETH_FCS_LEN + VLAN_HLEN expression should be surrounded
with parentheses.
Wrap mentioned expression and take into account VLAN double tagging.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Commit 87b0984ebf ("net: Add extack argument to ndo_fdb_add()") in
net-next added an extended parameter to the .ndo_fdb_add op and changed
ice_fdb_add() accordingly. Update the function header and add the
__always_unused attribute to the new parameter to avoid -Wunused-parameter
warnings.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
No current DSA driver makes use of the phydev parameter passed to the
disable_port call. Remove it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the switch to phy_resolve_aneg_linkmode() we don't read from the
chip any longer what is advertised but use phydev->advertising directly.
For a fixed phy however this bitmap is empty so far, what results in
no common mode being found. This breaks DSA. Fix this by advertising
everything that is supported. For a normal phy this done by phy_probe().
Fixes: 5502b218e0 ("net: phy: use phy_resolve_aneg_linkmode in genphy_read_status")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Auto-neg emulation currently doesn't set bit BMCR_ANENABLE in BMCR,
add this. Users will ignore speed and duplex settings in BMCR because
we're emulating auto-neg, therefore we can remove related code.
See also following discussion [0].
[0] https://marc.info/?t=155041784900002&r=1&w=2
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to hold the register lock while requesting the GPIO
interrupt. By not holding it we can also avoid a false positive
lockdep splat.
Reported-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following false positive lockdep splat has been observed.
======================================================
WARNING: possible circular locking dependency detected
4.20.0+ #302 Not tainted
------------------------------------------------------
systemd-udevd/160 is trying to acquire lock:
edea6080 (&chip->reg_lock){+.+.}, at: __setup_irq+0x640/0x704
but task is already holding lock:
edff0340 (&desc->request_mutex){+.+.}, at: __setup_irq+0xa0/0x704
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (&desc->request_mutex){+.+.}:
mutex_lock_nested+0x1c/0x24
__setup_irq+0xa0/0x704
request_threaded_irq+0xd0/0x150
mv88e6xxx_probe+0x41c/0x694 [mv88e6xxx]
mdio_probe+0x2c/0x54
really_probe+0x200/0x2c4
driver_probe_device+0x5c/0x174
__driver_attach+0xd8/0xdc
bus_for_each_dev+0x58/0x7c
bus_add_driver+0xe4/0x1f0
driver_register+0x7c/0x110
mdio_driver_register+0x24/0x58
do_one_initcall+0x74/0x2e8
do_init_module+0x60/0x1d0
load_module+0x1968/0x1ff4
sys_finit_module+0x8c/0x98
ret_fast_syscall+0x0/0x28
0xbedf2ae8
-> #0 (&chip->reg_lock){+.+.}:
__mutex_lock+0x50/0x8b8
mutex_lock_nested+0x1c/0x24
__setup_irq+0x640/0x704
request_threaded_irq+0xd0/0x150
mv88e6xxx_g2_irq_setup+0xcc/0x1b4 [mv88e6xxx]
mv88e6xxx_probe+0x44c/0x694 [mv88e6xxx]
mdio_probe+0x2c/0x54
really_probe+0x200/0x2c4
driver_probe_device+0x5c/0x174
__driver_attach+0xd8/0xdc
bus_for_each_dev+0x58/0x7c
bus_add_driver+0xe4/0x1f0
driver_register+0x7c/0x110
mdio_driver_register+0x24/0x58
do_one_initcall+0x74/0x2e8
do_init_module+0x60/0x1d0
load_module+0x1968/0x1ff4
sys_finit_module+0x8c/0x98
ret_fast_syscall+0x0/0x28
0xbedf2ae8
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&desc->request_mutex);
lock(&chip->reg_lock);
lock(&desc->request_mutex);
lock(&chip->reg_lock);
&desc->request_mutex refer to two different mutex. #1 is the GPIO for
the chip interrupt. #2 is the chained interrupt between global 1 and
global 2.
Add lockdep classes to the GPIO interrupt to avoid this.
Reported-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves setting of the current state into the loop. Otherwise
the task may end up in a busy wait loop if none of the break conditions
are met.
Signed-off-by: Timur Celik <mail@timurcelik.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
If hns3_client_start() failed in the hns3_client_init(),
register_dev() should be undo in its error handling.
Fixes: a6d818e31d ("net: hns3: Add vport alive state checking support")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Presently the hns reset_type for the roce errors is set
in the hclge_log_and_clear_rocee_ras_error function.
This function is also called to detect and clear roce errors
while enabling the rdma error interrupts. However there is no hns
reset requested for this case. This can cause issue of wrong
reset_type used with subsequent hns reset as the
reset_type set in the above case was not cleared.
This patch moves setting of hns reset_type for the roce errors from
hclge_log_and_clear_rocee_ras_error function
to hclge_handle_rocee_ras_error.
Fixes: 630ba007f4 ("net: hns3: add handling of RDMA RAS errors")
Reported-by: Huazhong Tan <tanhuazhong@huawei.com>
Reported-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: Shiju Jose <shiju.jose@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For revision 0x20, VF shares the same RSS config with PF.
In original codes, it always return 0 when query RSS hash
key for VF. This patch fixes it by return the hash key
got from PF.
Fixes: 374ad29176 ("net: hns3: net: hns3: Add RSS general configuration support for VF")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For revision 0x21, the switch of VF VLAN filter is per function.
It's necessary to enable VF VLAN filter for each VF when initializing.
Otherwise, VF will be able to receive broadcast packets with unknown
VLAN when PF enters promisc mode.
Fixes: 64d114f0a7 ("net: hns3: Add egress/ingress vlan filter for revision 0x21")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support to config depth for tx|rx ring separately
by ethtool command "-G".
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hnae3_get_bit uses hnae3_get_field, and hnae3_get_field
masks the data, which is unnecessary in data path.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hnae3_set_bit and hnae3_set_field masks the data before setting
the field or bit, which is unnecessary because the data is already
zero initialized.
Suggested-by: John Garry <john.garry@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds unlikely hint for error handling in critical data
path.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fill_desc ops has only one implementation, and
get_rxd_bnum has not been used, so this patch removes
them.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch limits some variables' scope as much as possible in
hns3_fill_desc.
Also, only set l3_type and l4_type when necessary.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch uses shift offset to avoid doing mult and div operation.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds xps setting support for hns3 driver based on
the interrupt affinity info.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hit the new tracepoint once the vregion migration ends.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Other mutexes are taking care of proper locking for this, no longer
needed to take RTNL mutex here.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No longer require RTNL lock in this code. Newly introduced mutexes take
care of guarding objagg and bloom filter. There is no need to guard
gen_pool_alloc()/gen_pool_free() as they are fine to be called lockless.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Relax dependency on rtnl mutex during vregion_rehash_intrvl_set(). The
vregion list is protected with newly introduced mutex.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Protect objagg structures by adding a mutex to ERP code and take it
during the structure manipulation.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For MR ACL profile is does not make sense to do periodical rehashes, as
there is only one mask in use during the whole vregion lifetime.
Therefore periodical work is scheduled but the rehash never happens.
So allow to enable/disable rehash for the whole group, which is added
per-profile. Disable rehashing for MR profile.
Addition to the vregion list is done only in case the rehash is enable
on the particular vregion. Also, the addition is moved after delayed
work init to avoid schedule of uninitialized work
from vregion_rehash_intrvl_set(). Symmetrically, deletion from
the list is done before canceling the delayed work so it is
not scheduled by vregion_rehash_intrvl_set() again.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bloom filter is shared within multiple regions. For updates, it needs to
be guarded by a separate mutex. Do that in order to not rely on RTNL
mutex.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to remove dependency on RTNL, introduce a mutex
to guard vregion structure, list of chunks and list of entries in
chunks.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor existing _vchunk_assoc/_vchunk_deassoc() functions into
_vregion_get()/_vregion_put() to make the code simpler and prepared for
vregion locking.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to remove RTNL lock dependency, it is needed to protect
the regions list in a group. Introduce a mutex to do the job.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the existing group structure to contain fields needed for HW region
list manipulations. Move the rest of the fields into new vgroup struct.
This makes layering cleaner as the vgroup struct is on higher level than
low-level group struct. Also, this makes it possible to introduce
fine-grained locking.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Never used, remove it.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add port_cleanup function to reset some device variables when the port is
disabled. Add a mutex to make sure changing those variables is
thread-safe.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unnecessary header include.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get port link status to know whether to read MIB counters when the link
is going down.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add background MIB counter reading support.
Port MIB counters should only be read when there is link. Otherwise it is
a waste of time as hardware never increases those counters. There are
exceptions as some switches keep track of dropped counts no matter what.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prepare PHY for proper advertisement as sometimes the PHY in the switch
has its own problems even though it may share the PHY id from regular PHY
but the fixes in the PHY driver do not apply.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the 88x2110 PHY, which is similar to the
already supported 88x3310 PHY without the SFP interface.
It supports 10/100/1000BASET along with 2.5GBASET, 5GBASET and 10GBASET,
with the same interface modes that are used by the 3310.
This PHY don't have the same issue as the 88x3310 regarding 2.5/5G
abilities, and correctly follows the 802.3bz standard to list the
supported abilities.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Suggested-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PPv2 controller is able to support 2.5G speeds, allowing to use
2.5GBASET in conjunction with PHYs that use 2500BASEX as their MII
interface when using this mode.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
As per 802.3bz, if bit 14 of (1.11) "PMA Extended Abilities" indicates
whether or not we should read register (1.21) "2.52/5G PMA Extended
Abilities", which contains information on the support of 2.5GBASET and
5GBASET.
After testing on several variants of PHYS of this family, it appears
that bit 14 in (1.11) isn't always set when it should be.
PHYs 88X3310 (on MacchiatoBin) and 88E2010 do support 2.5G and 5GBASET,
but don't have 1.11.14 set. Their register 1.21 is filled with the
correct values, indicating 2.5G and 5G support.
PHYs 88E2110 do have their 1.11.14 bit set, as it should.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY ID corresponding to the 88X3310 is also used for other PHYs in
the same family, such as the 88E2010. Use a #define for the PHY id, that
ignores the last nibble.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Marvell Alaska family of PHYs supports 2.5GBaseT and 5GBaseT modes,
as defined in the 802.3bz specification.
Upon establishing a 2.5GBASET link, the PHY will reconfigure it's MII
interface to 2500BASEX.
At 5G, the PHY will reconfigure it's interface to 5GBASE-R, but this
mode isn't supported by any MAC for now.
This was tested with :
- The 88X3310, which is on the MacchiatoBin
- The 88E2010, an Alaska PHY that has no fiber interfaces, and is
limited to 5G maximum speed.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cosmetic patch making use of helpers dedicated to linkmodes handling.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Alaska family of 10G PHYs has more abilities than the ones listed in
PHY_10GBIT_FULL_FEATURES, the exact list depending on the model.
Make use of the newly introduced .get_features call to build this list,
using genphy_c45_pma_read_abilities to build the list of supported
linkmodes, and adding autoneg ability based on what's reported by the AN
MMD.
.config_init is still used to validate the interface_mode.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code reports a link as up if all devices (except a few
blacklisted ones) report the link as up. This breaks Aquantia AQCS109
for lower speeds because on this PHY the PCS link status reflects a
10G link only. For Marvell there's a similar issue, therefore PHYXS
device isn't checked.
There may be more PHYs where depending on the mode the link status
of only selected devices is relevant.
For now it seems to be sufficient to check the link status of the
PMAPMD device only. Leave the loop in the code to be prepared in
case we have to add functionality to check more than one device,
depending on the mode.
Successfully tested on a board with an AQCS109.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is no longer necessary after eca59f6915 ("net: Remove support for bridge bypass ndos from stacked devices")
Suggested-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andy Gospodarek <andy@greyhouse.net>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is no longer necessary after a5084bb71f ("nfp: Implement
ndo_get_port_parent_id()")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
eth_change_mtu() is not needed any more, the networking subsystem will
call it automatically when this callback is not implemented.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the file names of the FW files which this driver handles into
the module description.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ndo_change_proto_down support through dev_change_proto_down_generic
for use by control protocols like VRRPD.
Signed-off-by: Andy Roulin <aroulin@cumulusnetworks.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ndo_change_proto_down support through dev_change_proto_down_generic
for use by control protocols like VRRPD.
Signed-off-by: Andy Roulin <aroulin@cumulusnetworks.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using genphy_c45_read_abilities() as get_features callback we
also have to set the autoneg capability in phydev->supported.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Three conflicts, one of which, for marvell10g.c is non-trivial and
requires some follow-up from Heiner or someone else.
The issue is that Heiner converted the marvell10g driver over to
use the generic c45 code as much as possible.
However, in 'net' a bug fix appeared which makes sure that a new
local mask (MDIO_AN_10GBT_CTRL_ADV_NBT_MASK) with value 0x01e0
is cleared.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"Hopefully the last pull request for this release. Fingers crossed:
1) Only refcount ESP stats on full sockets, from Martin Willi.
2) Missing barriers in AF_UNIX, from Al Viro.
3) RCU protection fixes in ipv6 route code, from Paolo Abeni.
4) Avoid false positives in untrusted GSO validation, from Willem de
Bruijn.
5) Forwarded mesh packets in mac80211 need more tailroom allocated,
from Felix Fietkau.
6) Use operstate consistently for linkup in team driver, from George
Wilkie.
7) ThunderX bug fixes from Vadim Lomovtsev. Mostly races between VF
and PF code paths.
8) Purge ipv6 exceptions during netdevice removal, from Paolo Abeni.
9) nfp eBPF code gen fixes from Jiong Wang.
10) bnxt_en firmware timeout fix from Michael Chan.
11) Use after free in udp/udpv6 error handlers, from Paolo Abeni.
12) Fix a race in x25_bind triggerable by syzbot, from Eric Dumazet"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (65 commits)
net: phy: realtek: Dummy IRQ calls for RTL8366RB
tcp: repaired skbs must init their tso_segs
net/x25: fix a race in x25_bind()
net: dsa: Remove documentation for port_fdb_prepare
Revert "bridge: do not add port to router list when receives query with source 0.0.0.0"
selftests: fib_tests: sleep after changing carrier. again.
net: set static variable an initial value in atl2_probe()
net: phy: marvell10g: Fix Multi-G advertisement to only advertise 10G
bpf, doc: add bpf list as secondary entry to maintainers file
udp: fix possible user after free in error handler
udpv6: fix possible user after free in error handler
fou6: fix proto error handler argument type
udpv6: add the required annotation to mib type
mdio_bus: Fix use-after-free on device_register fails
net: Set rtm_table to RT_TABLE_COMPAT for ipv6 for tables > 255
bnxt_en: Wait longer for the firmware message response to complete.
bnxt_en: Fix typo in firmware message timeout logic.
nfp: bpf: fix ALU32 high bits clearance bug
nfp: bpf: fix code-gen bug on BPF_ALU | BPF_XOR | BPF_K
Documentation: networking: switchdev: Update port parent ID section
...
This fixes a regression introduced by
commit 0d2e778e38
"net: phy: replace PHY_HAS_INTERRUPT with a check for
config_intr and ack_interrupt".
This assumes that a PHY cannot trigger interrupt unless
it has .config_intr() or .ack_interrupt() implemented.
A later patch makes the code assume both need to be
implemented for interrupts to be present.
But this PHY (which is inside a DSA) will happily
fire interrupts without either callback.
Implement dummy callbacks for .config_intr() and
.ack_interrupt() in the phy header to fix this.
Tested on the RTL8366RB on D-Link DIR-685.
Fixes: 0d2e778e38 ("net: phy: replace PHY_HAS_INTERRUPT with a check for config_intr and ack_interrupt")
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use new function genphy_c45_read_status(). 1000BaseT link partner
advertisement needs to be read from vendor registers.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to genphy_read_status() for Clause 22 add a generic read_status
function for Clause 45.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because 1000BaseT isn't covered by Clause 45, the 1000BaseT flags in
phydev->lp_advertising may have been set based on vendor registers
already. genphy_c45_read_lpa() would clear these flags as of today.
Therefore switch to mii_lpa_mod_linkmode_lpa_t.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of the generic c45 code, plus code specific to the Aquantia
phy for 1000BaseT negotiation.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
AQCS109 belongs to a family of PHY's where certain members don't
support 5G or 10G. However for all members of the family the chip
reports 10G and 5G capability. Therefore remove the not supported
modes for AQCS109.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This series adds some misc updates to mlx5 driver,
1) Eli Britstein, Introduces tunnel entropy control from PCMR register
and fixes GRE key by controlling port tunnel entropy calculation.
2) Eran Ben Elisha, provides some mlx5 fixes to the latest tx devlink health
reporting mechanism.
3) Huy Nguyen, Added the support for ndo bridge_setlink to allow
VEPA/VEB E-Switch legacy mode configurations.
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJccGvRAAoJEEg/ir3gV/o+6kIH/1Y23h0OZrKkkfELujtzoOjx
64BIRhW8Tr+WOXZNKlSvdRkPj0g1yG3B0NO7wChXZDl8dgqBp/Jx5Wxcvb5DKkz/
wK07oKB6KqgcMILzUe5G4iOHw/atMldzSA6sNPh8SDKVKKkXjMKz8ocQZZQRsAaX
1im2D77pX8zE/OhG86Fn23Fed1G6Lg++faPC8GEOxv9LkwaAARa5NfJ6g7AnXOGg
ijmM4R2Hhu0V0YaKXS2qJFb6HQaNO9JKYR1C7wF7z9yqnsn14cdxrAWkE4eA2JnP
zKnDt+ThAKAoX9mn5QHzD8uye56Jeksvo8br4dCH4iDZZSSZT+lo456Dfe+tXpc=
=ef79
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2019-02-21' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2019-02-21
This series adds some misc updates to mlx5 driver,
1) Eli Britstein, Introduces tunnel entropy control from PCMR register
and fixes GRE key by controlling port tunnel entropy calculation.
2) Eran Ben Elisha, provides some mlx5 fixes to the latest tx devlink health
reporting mechanism.
3) Huy Nguyen, Added the support for ndo bridge_setlink to allow
VEPA/VEB E-Switch legacy mode configurations.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Spectrum-2 ASIC support for the following new port types and speeds:
* 50Gbps 1-lane
* 100Gbps 2-lanes
* 200Gbps 4-lanes
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Spectrum-2 ASIC port type-speed operations.
Since multiple ethtool link modes are represented using a single bit in the
ASIC, the driver forces the user to configure all types per a specific
speed. For example, if the user wants to advertise 100Gbps 4-lanes speed,
he should advertise all the types of 100Gbps 4-lanes speed that are
supported by the ASIC as shown below:
Supported ethtool bits for 100Gbps 4-lanes:
0x1000000000 100000baseKR4 Full
0x2000000000 100000baseSR4 Full
0x4000000000 100000baseCR4 Full
0x8000000000 100000baseLR4_ER4 Full
Command for advertising 100Gbps 4-lanes:
ethtool -s enp3s0np1 advertise 0xF000000000
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PTYS register introduces a new layout for port type-speed fields. These
fields extend the existing ones in order to handle more types and speeds.
For example, the new 200Gbps speed.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename p_eth_proto_adm to p_eth_proto_admin in mlxsw_reg_ptys_eth_unpack
function.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add port type-speed operations in order to have different operations for
different ASICs. For now, both ASICs use the same pointer.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename port speed-type functions to be Spectrum-1 ASIC specific.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of deriving the port connector type from port admin state, query it
from firmware.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove eth_proto_lp_advertise field in PTYS register since it is not
supported by the firmware.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove duplicate port link mode entry from mlxsw_sp_port_link_mode.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
cards_found is a static variable, but when it enters atl2_probe(),
cards_found is set to zero, the value is not consistent with last probe,
so next behavior is not our expect.
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide a precision hint to snprintf() in order to eliminate a
-Wformat-truncation warning provided below. A maximum of 11 characters
is allowed to reach a maximum of 32 - 1 characters given a possible
maximum value of queues using up to UINT_MAX which occupies 10
characters. Incidentally 11 is the number of characters for
"xdp_packets" which is the largest string we append.
drivers/net/veth.c: In function 'veth_get_strings':
drivers/net/veth.c:118:47: warning: '%s' directive output may be
truncated writing up to 31 bytes into a region of size between 12 and 21
[-Wformat-truncation=]
snprintf(p, ETH_GSTRING_LEN, "rx_queue_%u_%s",
^~
drivers/net/veth.c:118:5: note: 'snprintf' output between 12 and 52
bytes into a destination of size 32
snprintf(p, ETH_GSTRING_LEN, "rx_queue_%u_%s",
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
i, veth_rq_stats_desc[j].desc);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide precision hints to snprintf() since we know the destination
buffer size of the RX/TX ring names are IFNAMSIZ + 5 - 1. This fixes the
following warnings:
drivers/net/ethernet/intel/e1000e/netdev.c: In function
'e1000_request_msix':
drivers/net/ethernet/intel/e1000e/netdev.c:2109:13: warning: 'snprintf'
output may be truncated before the last format character
[-Wformat-truncation=]
"%s-rx-0", netdev->name);
^
drivers/net/ethernet/intel/e1000e/netdev.c:2107:3: note: 'snprintf'
output between 6 and 21 bytes into a destination of size 20
snprintf(adapter->rx_ring->name,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
sizeof(adapter->rx_ring->name) - 1,
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
"%s-rx-0", netdev->name);
~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/intel/e1000e/netdev.c:2125:13: warning: 'snprintf'
output may be truncated before the last format character
[-Wformat-truncation=]
"%s-tx-0", netdev->name);
^
drivers/net/ethernet/intel/e1000e/netdev.c:2123:3: note: 'snprintf'
output between 6 and 21 bytes into a destination of size 20
snprintf(adapter->tx_ring->name,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
sizeof(adapter->tx_ring->name) - 1,
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
"%s-tx-0", netdev->name);
~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are not specifying an explicit format argument but instead passing a
string litteral which causes these two warnings to show up:
drivers/net/dsa/mv88e6xxx/chip.c: In function
'mv88e6xxx_irq_poll_setup':
drivers/net/dsa/mv88e6xxx/chip.c:483:2: warning: format not a string
literal and no format arguments [-Wformat-security]
chip->kworker = kthread_create_worker(0, dev_name(chip->dev));
^~~~
drivers/net/dsa/mv88e6xxx/ptp.c: In function 'mv88e6xxx_ptp_setup':
drivers/net/dsa/mv88e6xxx/ptp.c:403:4: warning: format not a string
literal and no format arguments [-Wformat-security]
dev_name(chip->dev));
^~~~~~~~
LD [M] drivers/net/dsa/mv88e6xxx/mv88e6xxx.o
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Give precision identifiers to the two snprintf() formatting the priority
and TC strings to avoid producing these two warnings:
drivers/net/ethernet/mellanox/mlxsw/spectrum.c: In function
'mlxsw_sp_port_get_prio_strings':
drivers/net/ethernet/mellanox/mlxsw/spectrum.c:2132:37: warning: '%d'
directive output may be truncated writing between 1 and 3 bytes into a
region of size between 0 and 31 [-Wformat-truncation=]
snprintf(*p, ETH_GSTRING_LEN, "%s_%d",
^~
drivers/net/ethernet/mellanox/mlxsw/spectrum.c:2132:3: note: 'snprintf'
output between 3 and 36 bytes into a destination of size 32
snprintf(*p, ETH_GSTRING_LEN, "%s_%d",
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
mlxsw_sp_port_hw_prio_stats[i].str, prio);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/mellanox/mlxsw/spectrum.c: In function
'mlxsw_sp_port_get_tc_strings':
drivers/net/ethernet/mellanox/mlxsw/spectrum.c:2143:37: warning: '%d'
directive output may be truncated writing between 1 and 11 bytes into a
region of size between 0 and 31 [-Wformat-truncation=]
snprintf(*p, ETH_GSTRING_LEN, "%s_%d",
^~
drivers/net/ethernet/mellanox/mlxsw/spectrum.c:2143:3: note: 'snprintf'
output between 3 and 44 bytes into a destination of size 32
snprintf(*p, ETH_GSTRING_LEN, "%s_%d",
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
mlxsw_sp_port_hw_tc_stats[i].str, tc);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some Marvell Alaska PHYs support 2.5G, 5G and 10G BaseT links. Their
default behaviour is to advertise all of these modes, but at the moment,
only 10GBaseT is supported. To prevent link partners from establishing
link at that speed, clear these modes upon configuring aneg parameters.
Fixes: 20b2af32ff ("net: phy: add Marvell Alaska X 88X3310 10Gigabit PHY support")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reported-by: Russell King <linux@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf 2019-02-23
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix a bug in BPF's LPM deletion logic to match correct prefix
length, from Alban.
2) Fix AF_XDP teardown by not destroying umem prematurely as it
is still needed till all outstanding skbs are freed, from Björn.
3) Fix unkillable BPF_PROG_TEST_RUN under preempt kernel by checking
signal_pending() outside need_resched() condition which is never
triggered there, from Stanislav.
4) Fix two nfp JIT bugs, one in code emission for K-based xor, and
another one to explicitly clear upper bits in alu32, from Jiong.
5) Add bpf list address to maintainers file, from Daniel.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Per "Documentation/devicetree/bindings/net/ethernet.txt" RGMII mode
should not have delay in PHY whereas RGMII_ID and RGMII_RXID/RGMII_TXID
can have delay in PHY.
So disable the delay only for RGMII mode and enable for other modes.
Also treat the default case as disabled delays.
Fixes: cd28d1d6e5: ("net: phy: at803x: Disable phy delay for RGMII mode")
Reported-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Niklas Cassel <niklas.cassel@linaro.org>
Tested-by: Peter Ujfalusi <peter.ujflausi@ti.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some helpers were declared with the "inline" function specifier.
It is preferable to let the compiler pick the right optimizations,
so drop the specifier for at803x_disable_rx_delay() and
at803x_disable_tx_delay()
Reviewed-by: Niklas Cassel <niklas.cassel@linaro.org>
Tested-by: Peter Ujfalusi <peter.ujflausi@ti.com>
Reviewed-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code waits up to 20 usec for the firmware response to complete
once we've seen the valid response header in the buffer. It turns
out that in some scenarios, this wait time is not long enough.
Extend it to 150 usec and use usleep_range() instead of udelay().
Fixes: 9751e8e714 ("bnxt_en: reduce timeout on initial HWRM calls")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The logic that polls for the firmware message response uses a shorter
sleep interval for the first few passes. But there was a typo so it
was using the wrong counter (larger counter) for these short sleep
passes. The result is a slightly shorter timeout period for these
firmware messages than intended. Fix it by using the proper counter.
Fixes: 9751e8e714 ("bnxt_en: reduce timeout on initial HWRM calls")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NFP BPF JIT compiler is doing a couple of small optimizations when jitting
ALU imm instructions, some of these optimizations could save code-gen, for
example:
A & -1 = A
A | 0 = A
A ^ 0 = A
However, for ALU32, high 32-bit of the 64-bit register should still be
cleared according to ISA semantics.
Fixes: cd7df56ed3 ("nfp: add BPF to NFP code translator")
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
The intended optimization should be A ^ 0 = A, not A ^ -1 = A.
Fixes: cd7df56ed3 ("nfp: add BPF to NFP code translator")
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Allow enabling VEPA mode on the HCA's port in legacy devlink mode.
Example:
bridge link set dev ens1f0 hwmode vepa
will turn on VEPA mode on the netdev ens1f0.
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In Virtual Ethernet Port Aggregator (VEPA) mode, the packet skips
the system internal virtual switch and forwards to external network
switch. In Mellanox HCA case, the virtual switch is the HCA's Eswitch.
To support this, an new FDB flow table are created with level 0 and
linked to the existing FDB flow table in legacy mode. By default,
VEPA is turned off and this FDB flow table is empty. When VEPA is
turned on, two rules are created. One rule to forward on uplink vport
traffic to the legacy FDB. The other rule forward all other traffic
to uplink vport.
Other design alternatives were not chosen as explained below:
1. Create a forward rule in ACL flow table (most efficient design).
This approach is the not chosen because firmware does not support
forward rule to uplink vport (0xffff) for ACL flow table.
2. Add additional source port criteria in all the FDB rules to make the
FDB rules to be received rules only. This approach is not chosen because
it is not efficient as there can many rules in the FDB and VEPA mode
cannot be controlled per vport.
3. Add a highest prioirty flow group in the existing legacy FDB Flow
Table instead of a new flow table. This approoach does not work because the
new flow group has the same match criteria as the promiscuous flow group
and mlx5_add_flow_rules does not allow specifying flow group.
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
If reporter is ERR_PTR or NULL, error code shall be returned. At all other
cases it shall return success. Fix that.
Fixes: de8650a820 ("net/mlx5e: Add tx reporter support")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In case of lost interrupt recover, we shall return success. Fix that.
Fixes: 7d91126b1a ("net/mlx5e: Add tx timeout support for mlx5e tx reporter")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reported-by: Maria Pasechnik <mariap@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When TX reporter was introduced, it took ownership over TX timeout error
handling. this introduced a regression in case TX reporter is not valid
(NET_DEVLINK is not set, or devlink_health_reporter_create failure).
Fix mlx5e_tx_reporter_timeout function so it can be called at all times.
In addition, remove a warning print that indicates that a TX timeout won't
be handled in case of no valid TX reporter.
Fixes: 7d91126b1a ("net/mlx5e: Add tx timeout support for mlx5e tx reporter")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Print warning message in case of TX reporter creation failure, only if the
return value is ERR_PTR type. NULL pointer return indicates that
NET_DEVLINK is not set, and the warning print can be skipped.
Fixes: de8650a820 ("net/mlx5e: Add tx reporter support")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Flow entropy is calculated on the inner packet headers and used for
flow distribution in processing, routing etc. For GRE-type
encapsulations the entropy value is placed in the eight LSB of the key
field in the GRE header as defined in NVGRE RFC 7637. For UDP based
encapsulations the entropy value is placed in the source port of the
UDP header.
The hardware may support entropy calculation specifically for GRE and
for all tunneling protocols. With commit df2ef3bff1 ("net/mlx5e: Add
GRE protocol offloading") GRE is offloaded, but the hardware is
configured by default to calculate flow entropy so packets transmitted
on the wire have a wrong key. To support UDP based tunnels (i.e VXLAN),
GRE (i.e. no flow entropy) and NVGRE (i.e. with flow entropy) the
hardware behaviour must be controlled by the driver.
Ensure port entropy calculation is enabled for offloaded VXLAN tunnels
and disable port entropy calculation in the presence of offloaded GRE
tunnels by monitoring the presence of entropy enabling tunnels (i.e
VXLAN) and entropy disabing tunnels (i.e GRE).
Fixes: df2ef3bff1 ("net/mlx5e: Add GRE protocol offloading")
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently changing a PCMR field is done by setting the field in a
zeroed buffer, zeroing other unrelated fields.
Fix this behaviour by modifying only the required field after first
reading the current register values, as a pre-step towards using more
fields in PCMR register.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Most likely the last set of patches for 5.1. WPA3 support to ath10k
and qtnfmac. FTM support to iwlwifi and ath10k. And of course other
new features and bugfixes.
wireless-drivers was merged due to dependency in mt76.
Major changes:
iwlwifi
* HE radiotap
* FTM (Fine Timing Measurement) initiator and responder implementation
* bump supported firmware API to 46
* VHT extended NSS support
* new PCI IDs for 9260 and 22000 series
ath10k
* change QMI interface to support the new (and backwards incompatible)
interface from HL3.1 and used in recent HL2.0 branch firmware
releases
* support WPA3 with WCN3990
* support for mac80211 airtime fairness based on transmit rate
estimation, the firmware needs to support WMI_SERVICE_PEER_STATS to
enable this
* report transmit airtime to mac80211 with firmwares having
WMI_SERVICE_REPORT_AIRTIME feature, this to have more accurate
airtime fairness based on real transmit time (instead of just
estimated from transmit rate)
* support Fine Timing Measurement (FTM) responder role
* add dynamic VLAN support with firmware having WMI_SERVICE_PER_PACKET_SW_ENCRYPT
* switch to use SPDX license identifiers
ath
* add new country codes for US
brcmfmac
* support monitor frames with the hardware/ucode header
qtnfmac
* enable WPA3 SAE and OWE support
mt76
* beacon support for USB devices (mesh+ad-hoc only)
rtlwifi
* convert to use SPDX license identifiers
libertas_tf
* get the MAC address before registering the device
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJccAnlAAoJEG4XJFUm622bxxMH/2cz2GEuDQXOwfYLnCUwFES8
vqTdMWnlfqGQvsTyvtSp91KqsL3hE2FB1Cu3n6/vzND3C7afT0V2/QlU7Pmgr8sR
1gnJnu0NJT5SZfzcTsqwt8rFw9lQZ3HcvEcfNo6T5KUyyY7FGCNGR5H27nvoKOP3
ea1h7U80loPV40sGTI8jj963wa9LNHUrjHTK4wY+KMWECgZuD/fHeE9YPB9MTdff
lJ5bWCoQmuJddvTtC+X0tOAsCkxgdbbw6ieKqzep8H4gtUjerZD+V8uUdbtpr7IL
sWPoaqrrADMv9cZtDVj+pEtNIJ3mpfuHYFKSON9jy/uxygeFTfVzLu43RFreDp8=
=D15/
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2019-02-22' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 5.1
Most likely the last set of patches for 5.1. WPA3 support to ath10k
and qtnfmac. FTM support to iwlwifi and ath10k. And of course other
new features and bugfixes.
wireless-drivers was merged due to dependency in mt76.
Major changes:
iwlwifi
* HE radiotap
* FTM (Fine Timing Measurement) initiator and responder implementation
* bump supported firmware API to 46
* VHT extended NSS support
* new PCI IDs for 9260 and 22000 series
ath10k
* change QMI interface to support the new (and backwards incompatible)
interface from HL3.1 and used in recent HL2.0 branch firmware
releases
* support WPA3 with WCN3990
* support for mac80211 airtime fairness based on transmit rate
estimation, the firmware needs to support WMI_SERVICE_PEER_STATS to
enable this
* report transmit airtime to mac80211 with firmwares having
WMI_SERVICE_REPORT_AIRTIME feature, this to have more accurate
airtime fairness based on real transmit time (instead of just
estimated from transmit rate)
* support Fine Timing Measurement (FTM) responder role
* add dynamic VLAN support with firmware having WMI_SERVICE_PER_PACKET_SW_ENCRYPT
* switch to use SPDX license identifiers
ath
* add new country codes for US
brcmfmac
* support monitor frames with the hardware/ucode header
qtnfmac
* enable WPA3 SAE and OWE support
mt76
* beacon support for USB devices (mesh+ad-hoc only)
rtlwifi
* convert to use SPDX license identifiers
libertas_tf
* get the MAC address before registering the device
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
After AF_PACKET is fixed to calculate the transport header offset
correctly, trust the value set by the kernel. If the offset wasn't set,
it means there is no transport header in the packet.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_transport_offset() == 0 is not a special value. The only special
value is when skb->transport_header is ~0U, and it's checked by
skb_transport_header_was_set().
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the socket was created with socket(AF_PACKET, SOCK_RAW, 0),
skb->protocol will be unset, __skb_flow_dissect() will fail, and
skb_probe_transport_header() will fall back to the offset_hint, making
the resulting skb_transport_offset incorrect.
If, however, there is no transport header in the packet,
transport_header shouldn't be set to an arbitrary value.
Fix it by leaving the transport offset unset if it couldn't be found, to
be explicit rather than to fill it with some wrong value. It changes the
behavior, but if some code relied on the old behavior, it would be
broken anyway, as the old one is incorrect.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* the massive patch series for multi-BSSID support, I ended up
applying that through a side branch to record some details
* CSA improvements
* HE (802.11ax) updates to Draft 3.3
* strongly typed element iteration/etc. to make such code more
readable - this came up in particular in multi-BSSID
* rhashtable conversion patches from Herbert
Along, as usual, with various fixes and improvements.
-----BEGIN PGP SIGNATURE-----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=SM9w
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2019-02-22' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
This time we have, of note:
* the massive patch series for multi-BSSID support, I ended up
applying that through a side branch to record some details
* CSA improvements
* HE (802.11ax) updates to Draft 3.3
* strongly typed element iteration/etc. to make such code more
readable - this came up in particular in multi-BSSID
* rhashtable conversion patches from Herbert
Along, as usual, with various fixes and improvements.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
* mac80211 mesh code wasn't allocating SKB tailroom properly
in some cases
* tx_sk_pacing_shift should be 7 for better performance
* mac80211_hwsim wasn't propagating genlmsg_reply() errors
-----BEGIN PGP SIGNATURE-----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=JEqH
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2019-02-22' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Three more fixes:
* mac80211 mesh code wasn't allocating SKB tailroom properly
in some cases
* tx_sk_pacing_shift should be 7 for better performance
* mac80211_hwsim wasn't propagating genlmsg_reply() errors
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Since link change polling routine was moved to nicvf side,
we don't need anymore polling function at nicpf side along
with link status info for all enabled Vfs as at VF side
this info is already tracked.
This commit is to remove unnecessary code & fields from
nicpf structure.
Signed-off-by: Vadim Lomovtsev <vlomovtsev@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the link change polling task to VF side in order to
prevent races between VF and PF while sending link change
message(s). This commit is to implement link change request
to be initiated by VF.
Signed-off-by: Vadim Lomovtsev <vlomovtsev@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some cases it could happen that nicvf_send_msg_to_pf() could be called
concurrently for the same NIC VF, and thus re-writing mailbox contents and
breaking messaging sequence with PF by re-writing NICVF data.
This commit is to implement mutex for NICVF to protect mailbox registers
and NICVF messaging control data from concurrent access.
Signed-off-by: Vadim Lomovtsev <vlomovtsev@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To communicate to PF each of ThunderX NIC VF uses mailbox which is
pair of 64 bit registers available to both VFn and PF.
This commit is to change the xcast message structure in order to
fit it into 64 bit.
Signed-off-by: Vadim Lomovtsev <vlomovtsev@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rx_set_mode invokes number of messages to be send to PF for receive
mode configuration. In case if there any issues we need to stop sending
messages and release allocated memory.
This commit is to implement check of nicvf_msg_send_to_pf() result.
Signed-off-by: Vadim Lomovtsev <vlomovtsev@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At the end of NIC VF initialization VF sends CFG_DONE message to PF without
using nicvf_msg_send_to_pf routine. This potentially could re-write data in
mailbox. This commit is to implement common way of sending CFG_DONE message
by the same way with other configuration messages by using
nicvf_send_msg_to_pf() routine.
Signed-off-by: Vadim Lomovtsev <vlomovtsev@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Having one work queue for receive mode configuration ndo_set_rx_mode()
call for all VFs results in making each of them wait till the
set_rx_mode() call completes for another VF if any of close, set
receive mode and change flags calls being already invoked. Potentially
this could cause device state change before appropriate call of receive
mode configuration completes, so the call itself became meaningless,
corrupt data or break configuration sequence.
We don't need any delays in NIC VF configuration sequence so having delayed
work call with 0 delay has no sense.
This commit is to implement one work queue for each NIC VF for set_rx_mode
task and to let them work independently and replacing delayed_work
with work_struct.
Signed-off-by: Vadim Lomovtsev <vlomovtsev@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Correct STREERING to STEERING at macro name for BGX steering register.
Signed-off-by: Vadim Lomovtsev <vlomovtsev@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a port is added to a team, its initial state is derived
from netif_carrier_ok rather than netif_oper_up.
If it is carrier up but operationally down at the time of being
added, the port state.linkup will be set prematurely.
port state.linkup should be set consistently using
netif_oper_up rather than netif_carrier_ok.
Fixes: f1d22a1e05 ("team: account for oper state")
Signed-off-by: George Wilkie <gwilkie@vyatta.att-mail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new PHY driver call to get the PHYs supported features.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
[hkallweit1@gmail.com: removed new config_init callback from patch]
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RTL8153-BD is used in Dell DA300 type-C dongle.
Added RTL8153-BD support to activate MAC address pass through on DA300.
Apply correction on previously submitted patch in net.git tree.
Signed-off-by: David Chen <david.chen7@dell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When running Docker with userns isolation e.g. --userns-remap="default"
and spawning up some containers with CAP_NET_ADMIN under this realm, I
noticed that link changes on ipvlan slave device inside that container
can affect all devices from this ipvlan group which are in other net
namespaces where the container should have no permission to make changes
to, such as the init netns, for example.
This effectively allows to undo ipvlan private mode and switch globally to
bridge mode where slaves can communicate directly without going through
hostns, or it allows to switch between global operation mode (l2/l3/l3s)
for everyone bound to the given ipvlan master device. libnetwork plugin
here is creating an ipvlan master and ipvlan slave in hostns and a slave
each that is moved into the container's netns upon creation event.
* In hostns:
# ip -d a
[...]
8: cilium_host@bond0: <BROADCAST,MULTICAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default qlen 1000
link/ether 0c:c4:7a:e1:3d:cc brd ff:ff:ff:ff:ff:ff promiscuity 0 minmtu 68 maxmtu 65535
ipvlan mode l3 bridge numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535
inet 10.41.0.1/32 scope link cilium_host
valid_lft forever preferred_lft forever
[...]
* Spawn container & change ipvlan mode setting inside of it:
# docker run -dt --cap-add=NET_ADMIN --network cilium-net --name client -l app=test cilium/netperf
9fff485d69dcb5ce37c9e33ca20a11ccafc236d690105aadbfb77e4f4170879c
# docker exec -ti client ip -d a
[...]
10: cilium0@if4: <BROADCAST,MULTICAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default qlen 1000
link/ether 0c:c4:7a:e1:3d:cc brd ff:ff:ff:ff:ff:ff promiscuity 0 minmtu 68 maxmtu 65535
ipvlan mode l3 bridge numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535
inet 10.41.197.43/32 brd 10.41.197.43 scope global cilium0
valid_lft forever preferred_lft forever
# docker exec -ti client ip link change link cilium0 name cilium0 type ipvlan mode l2
# docker exec -ti client ip -d a
[...]
10: cilium0@if4: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default qlen 1000
link/ether 0c:c4:7a:e1:3d:cc brd ff:ff:ff:ff:ff:ff promiscuity 0 minmtu 68 maxmtu 65535
ipvlan mode l2 bridge numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535
inet 10.41.197.43/32 brd 10.41.197.43 scope global cilium0
valid_lft forever preferred_lft forever
* In hostns (mode switched to l2):
# ip -d a
[...]
8: cilium_host@bond0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default qlen 1000
link/ether 0c:c4:7a:e1:3d:cc brd ff:ff:ff:ff:ff:ff promiscuity 0 minmtu 68 maxmtu 65535
ipvlan mode l2 bridge numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535
inet 10.41.0.1/32 scope link cilium_host
valid_lft forever preferred_lft forever
[...]
Same l3 -> l2 switch would also happen by creating another slave inside
the container's network namespace when specifying the existing cilium0
link to derive the actual (bond0) master:
# docker exec -ti client ip link add link cilium0 name cilium1 type ipvlan mode l2
# docker exec -ti client ip -d a
[...]
2: cilium1@if4: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000
link/ether 0c:c4:7a:e1:3d:cc brd ff:ff:ff:ff:ff:ff promiscuity 0 minmtu 68 maxmtu 65535
ipvlan mode l2 bridge numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535
10: cilium0@if4: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default qlen 1000
link/ether 0c:c4:7a:e1:3d:cc brd ff:ff:ff:ff:ff:ff promiscuity 0 minmtu 68 maxmtu 65535
ipvlan mode l2 bridge numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535
inet 10.41.197.43/32 brd 10.41.197.43 scope global cilium0
valid_lft forever preferred_lft forever
* In hostns:
# ip -d a
[...]
8: cilium_host@bond0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default qlen 1000
link/ether 0c:c4:7a:e1:3d:cc brd ff:ff:ff:ff:ff:ff promiscuity 0 minmtu 68 maxmtu 65535
ipvlan mode l2 bridge numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535
inet 10.41.0.1/32 scope link cilium_host
valid_lft forever preferred_lft forever
[...]
One way to mitigate it is to check CAP_NET_ADMIN permissions of
the ipvlan master device's ns, and only then allow to change
mode or flags for all devices bound to it. Above two cases are
then disallowed after the patch.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Three smallish patches fixing regressions in v5.0:
- Fix cxgb4 to work again with non-4k page sizes
- NULL pointer oops in SRP during sg_reset
-----BEGIN PGP SIGNATURE-----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=JFU9
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma fixes from Jason Gunthorpe:
"Small set of three regression fixing patches, things are looking
pretty good here.
- Fix cxgb4 to work again with non-4k page sizes
- NULL pointer oops in SRP during sg_reset"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
iw_cxgb4: cq/qp mask depends on bar2 pages in a host page
cxgb4: Export sge_host_page_size to ulds
RDMA/srp: Rework SCSI device reset handling
Merge net-next to resolve a conflict and to get the mac80211
rhashtable fixes so further patches can be applied on top.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Update element names and new fields according to D3.3 of
the HE spec.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
genlmsg_reply can fail, so propagate its return code
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A missing break keyword should have been added after adding support for
PRE_BRIDGE_FLAGS.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Fixes: 93700458ff ("rocker: Check Handle PORT_PRE_BRIDGE_FLAGS")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the hardware's description, the driver should clear
the command queue's registers when uloading VF driver. Otherwise,
these existing value may lead the IMP get into a wrong state.
Fixes: fedd0c15d2 ("net: hns3: Add HNS3 VF IMP(Integrated Management Proc) cmd interface")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the hardware's description, the driver should clear
the command queue's registers when uloading driver. Otherwise,
these existing value may lead the IMP get into a wrong state.
Also this patch adds hclge_cmd_uninit() to do the command queue
uninitialization which includes clearing registers and freeing
memory.
Fixes: 68c0a5c706 ("net: hns3: Add HNS3 IMP(Integrated Mgmt Proc) Cmd Interface Support")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Record the vlan tables that the VF sends to the chip.
After the VF exception, the PF actively clears the VF to chip config.
Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Record the unicast and multicast tables that the VF sends to the chip.
After the VF exception, the PF actively clears the VF to chip config.
Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch modify print message of 6th bit of ppp mpf abnormal errors,
there is a extra letter e in it.
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These bits are enabled now and have been test.
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 3rd and 4th of PPU(RCB) PF Abnormal is RAS errors instead of MSI-X
like other bits. This patch adds process of handling and logging this
two bits. Otherwise, this patch modifies print message of 28th and 29th
bit of PPU MPF Abnormal errors, which keep same with other errors now.
Fixes: f69b10b317 ("net: hns3: handle hw errors of PPU(RCB)")
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add information of specific bit in log to be consistent
with other type of errors, so that we can know which memory of ssu
has occurred a ecc ras errors.
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In original codes, for copper port which doesn't connect to phy,
it always returns -EOPNOTSUPP when query port information. This
patch fixes it by return the port information of MAC.
Fixes: 5f373b1585 ("net: hns3: Fix speed/duplex information loss problem when executing ethtool ethx cmd of VF")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The link mode with bits has been up to more than 31 for some MAC
and phy. Convert to using a linkmode bitmap, which can support all
link modes.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In hnae3_register_ae_dev(), ae_algo->ops is assigned to ae_dev->ops
before check that ae_algo->ops is valid.
And in hnae3_register_ae_algo(), missing check for ae_algo->ops.
This patch fixes them.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These functions are exported, add pointer checking at the beginning
can make them more safe.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
cap_max_headroom_size holds maximum headroom size supported.
Overstepping that limit might under certain conditions lead to ASIC
freeze.
Query and store the value, and add mlxsw_sp_sb_max_headroom_cells() for
obtaining the stored value. In __mlxsw_sp_port_headroom_set(), reject
requests where the total port buffer is larger than the advertised
maximum.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recommendation for headroom size for 100Gbps port and 100m cable is
101.6KB, reduced accordingly for split ports. The closest higher number
evenly divisible by cell size for both Spectrum-1 and Spectrum-2, and
such that the number of cells can be further divided by maximum split
factor of 4, is 102528 bytes, or 25632 bytes per lane.
Update mlxsw_sp_port_pb_init() to compute the headroom taking into
account this recommended per-lane value and number of lanes actually
dedicated to a given port.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Customize the tables related to shared buffer configuration to match the
current recommendation for Spectrum-2 systems.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SBMM register configures the shared buffer quota for MC packets
according to Switch-Priority. The default configuration depends on the
chip type. Therefore keep the table and length in struct
mlxsw_sp_sb_vals. Redirect the references from the global definitions to
the fields.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SBCM register configures shared buffer quota according to
port-priority resp. port-TC. The default configuration depends on the
chip type. Therefore keep the tables and their lengths in struct
mlxsw_sp_sb_vals. Redirect the references from the global definitions to
the fields.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SBPR register configures shared buffer pools. The default
configuration depends on the chip type. Therefore keep it in struct
mlxsw_sp_sb_vals. Redirect the one reference from the global array to
the field.
Because the pool descriptor ID is implicit in the ordering of array
members, both this array and the pool descriptor array have the same
length. Therefore reuse mlxsw_sp_sb.pool_dess_len for the purpose of
determining the length of SBPR array.
Drop the now useless MLXSW_SP_SB_PRS_LEN.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SBPM register can be used to configure quotas for packets ingressing
from a certain pool to a certain port, and egressing from a certain pool
to a certain port. The default configuration depends on the chip type.
Therefore keep it in struct mlxsw_sp_sb_vals. Redirect the one reference
from the global array to the field.
Because the pool descriptor ID is implicit in the ordering of array
members, both this array and the pool descriptor array have the same
length. Therefore reuse mlxsw_sp_sb.pool_dess_len for the purpose of
determining the length of SBPM array.
Drop the now useless MLXSW_SP_SB_PMS_LEN.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Keep the table of pool descriptors and its length in struct
mlxsw_sp_sb_vals so that it can be specialized per chip type. Redirect
all users from the global definitions to the mlxsw_sp_sb fields.
Give mlxsw_sp_pool_count() an extra mlxsw_sp parameter so that it can
access the descriptor table.
Drop the now unnecessary MLXSW_SP_SB_POOL_DESS_LEN.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spectrum-2 will be configured with a different set of pools than
Spectrum-1. The size of prs and pms buffers will therefore depend on the
chip type of the device.
Therefore, instead of reserving an array directly in a structure
definition, allocate the buffer in mlxsw_sp_sb_port{,s}_init().
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spectrum-2 will be configured with a different shared buffer
configuration than Spectrum-1. Therefore introduce a structure for
keeping the chip-specific default and immutable configuration.
Configuration mutable in runtime will still be kept in struct
mlxsw_sp_sb.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TBU interrupt is a normal interrupt and can be used to trigger the
cleaning of TX path. Lets check if it's active in DMA interrupt handler.
While at it, refactor a little bit the function:
- Don't check if RI is enabled because at function exit we will
only clear the interrupts that are enabled so, no event will
be missed.
In my tests withe XGMAC2 this increased performance.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TBU interrupt is a normal interrupt and can be used to trigger the
cleaning of TX path. Lets check if it's active in DMA interrupt handler.
While at it, refactor a little bit the function:
- Don't check if RI is enabled because at function exit we will
only clear the interrupts that are enabled so, no event will be
missed.
In my tests with GMAC5 this increased performance.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 8fce333170 introduced the concept of NAPI per-channel and
independent cleaning of TX path.
This is currently breaking performance in some cases. The scenario
happens when all packets are being received in Queue 0 but the TX is
performed in Queue != 0.
Fix this by using different NAPI instances per each TX and RX queue, as
suggested by Florian.
Changes from v2:
- Only force restart transmission if there are pending packets
Changes from v1:
- Pass entire ring size to TX clean path (Florian)
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the bridge no longer calling switchdev_port_attr_get() to obtain
the supported bridge port flags from a driver but instead trying to set
the bridge port flags directly and relying on driver to reject
unsupported configurations, we can effectively get rid of
switchdev_port_attr_get() entirely since this was the only place where
it was called.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have converted the bridge code and the drivers to check for
bridge port(s) flags at the time we try to set them, there is no need
for a get() -> set() sequence anymore and
SWITCHDEV_ATTR_ID_PORT_BRIDGE_FLAGS_SUPPORT therefore becomes unused.
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for getting rid of switchdev_port_attr_get(), have rocker
check for the bridge flags being set through switchdev_port_attr_set()
with the SWITCHDEV_ATTR_ID_PORT_PRE_BRIDGE_FLAGS attribute identifier.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for getting rid of switchdev_port_attr_get(), have mlxsw
check for the bridge flags being set through switchdev_port_attr_set()
when the SWITCHDEV_ATTR_ID_PORT_PRE_BRIDGE_FLAGS attribute identifier is
used.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the bridge flags to Marvell 88e6xxx bridges, allowing
the multicast and unicast flood properties to be controlled. These
can be controlled on a per-port basis via commands such as:
bridge link set dev lan1 flood on|off
bridge link set dev lan1 mcast_flood on|off
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a subtle PACKET_ORIGDEV regression which was a side
effect of fixes introduced by:
6a9e461f6f bonding: pass link-local packets to bonding master also.
... to:
b89f04c61e bonding: deliver link-local packets with skb->dev set to link that packets arrived on
While 6a9e461f6f restored pre-b89f04c61efe presence of link-local
packets on bonding masters (which is required e.g. by linux bridges
participating in spanning tree or needed for lab-like setups created
with group_fwd_mask) it also caused the originating device
information to be lost due to cloning.
Maciej Żenczykowski proposed another solution that doesn't require
packet cloning and retains original device information - instead of
returning RX_HANDLER_PASS for all link-local packets it's now limited
only to packets from inactive slaves.
At the same time, packets passed to bonding masters retain correct
information about the originating device and PACKET_ORIGDEV can be used
to determine it.
This elegantly solves all issues so far:
- link-local packets that were removed from bonding masters
- LLDP daemons being forced to explicitly bind to slave interfaces
- PACKET_ORIGDEV having no effect on bond interfaces
Fixes: 6a9e461f6f (bonding: pass link-local packets to bonding master also.)
Reported-by: Vincent Bernat <vincent@bernat.ch>
Signed-off-by: Michal Soltys <soltys@ziu.info>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similiar to commit e94cd8113c ("net: remove MTU limits for dummy and
ifb device"), MTU is irrelevant for VRF device. We init it as 64K while
limit it to [68, 1500] may make users feel confused.
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use new function genphy_c45_check_and_restart_aneg() to reduce
boilerplate code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function will be used by config_aneg callback implementations of
PHY drivers and allows to reduce boilerplate code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like in genphy_config_aneg() for clause 22 PHY's, we should keep modes
from being advertised that are known to be broken with EEE.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We want to use this function in phy-c45.c too, therefore export it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If link partner and we can't agree on any mode, then it doesn't make
sense to pretend we would have agreed on 10/half. Therefore set a
proper default.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After recent changes to genphy_read_status() this orphaned register
read remained as leftover. So remove it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An issue has been found while testing zero-copy XDP that
causes a reset to be triggered. As it takes some time to
turn the carrier on after setting zc, and we already
start trying to transmit some packets, watchdog considers
this as an erroneous state and triggers a reset.
Don't do any work if netif carrier is not OK.
Fixes: 8221c5eba8 (ixgbe: add AF_XDP zero-copy Tx support)
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the driver clears the XDP xmit ring due to re-configuration or
teardown, in-progress ndo_xdp_xmit must be taken into consideration.
The ndo_xdp_xmit function is typically called from a NAPI context that
the driver does not control. Therefore, we must be careful not to
clear the XDP ring, while the call is on-going. This patch adds a
synchronize_rcu() to wait for napi(s) (preempt-disable regions and
softirqs), prior clearing the queue. Further, the __I40E_CONFIG_BUSY
flag is checked in the ndo_xdp_xmit implementation to avoid touching
the XDP xmit queue during re-configuration.
Fixes: d9314c474d ("i40e: add support for XDP_REDIRECT")
Fixes: 123cecd427 ("i40e: added queue pair disable/enable functions")
Reported-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the RX rings are created they are also populated with buffers so
that packets can be received. Usually these are kernel buffers, but
for AF_XDP in zero-copy mode, these are user-space buffers and in this
case the application might not have sent down any buffers to the
driver at this point. And if no buffers are allocated at ring creation
time, no packets can be received and no interrupts will be generated so
the NAPI poll function that allocates buffers to the rings will never
get executed.
To rectify this, we kick the NAPI context of any queue with an
attached AF_XDP zero-copy socket in two places in the code. Once after
an XDP program has loaded and once after the umem is registered. This
take care of both cases: XDP program gets loaded first then AF_XDP
socket is created, and the reverse, AF_XDP socket is created first,
then XDP program is loaded.
Fixes: d0bcacd0a1 ("ixgbe: add AF_XDP zero-copy Rx support")
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the RX rings are created they are also populated with buffers
so that packets can be received. Usually these are kernel buffers,
but for AF_XDP in zero-copy mode, these are user-space buffers and
in this case the application might not have sent down any buffers
to the driver at this point. And if no buffers are allocated at ring
creation time, no packets can be received and no interrupts will be
generated so the NAPI poll function that allocates buffers to the
rings will never get executed.
To rectify this, we kick the NAPI context of any queue with an
attached AF_XDP zero-copy socket in two places in the code. Once
after an XDP program has loaded and once after the umem is registered.
This take care of both cases: XDP program gets loaded first then AF_XDP
socket is created, and the reverse, AF_XDP socket is created first,
then XDP program is loaded.
Fixes: 0a714186d3 ("i40e: add AF_XDP zero-copy Rx support")
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Read port count from the shared memory instead of driver deriving this
value. This change simplifies the driver implementation and also avoids
any dependencies for finding the port-count.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Michal Kalderon <mkalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The enabling L3/L4 filtering for transmit switched packets for all
devices caused unforeseen issue on older devices when trying to send UDP
traffic in an ordered sequence. This bit was originally intended for X550
devices, which supported this feature, so limit the scope of this bit to
only X550 devices.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
There are rare cases where a PL_INT_CAUSE bit may end up getting
set when the corresponding PL_INT_ENABLE bit isn't set.
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that genphy_c45_pma_setup_forced() makes sure the "aneg enabled"
bit is cleared, the call to genphy_c45_an_disable_aneg() isn't needed
any longer. And the code pattern is now the same as in
genphy_config_aneg().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When genphy_c45_pma_setup_forced() is called the "aneg enabled" bit may
still be set, therefore clear it. This is also in line with what
genphy_setup_forced() does for Clause 22.
v2:
- fix typo
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This series includes misc updates to mlx5 drivers and one ethtool update.
1) From Aya Levin:
- ethtool: Define 50Gbps per lane link modes
- add support for 50Gbps per lane link modes in mlx5 driver
2) From Tariq Toukan,
- Add a helper function to unify mlx5 resource reloading
3) From Vlad Buslov,
- Remove wrong and superfluous tc pedit header type check
4) From Tonghao Zhang,
- Some refactoring in en_tc.c to simplify the mlx5e_tc_add_fdb_flow
5) From Leon Romanovsky & Saeed,
- Compilation warning fixes
6) From Bodong wang,
- E-Switch fixes that are related to the SmarNIC series
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJcbH/oAAoJEEg/ir3gV/o+bJQIAKIbILkQsAIn3B3U1Y7WgE8l
4pXdcYe6A3Mr9ZOi+U2ovJqVEHKPc7ASNfBfK5zsRayxhDQmoNhaloZSlwkgxenN
+guf86OBqTmXq9vzk3AFfPbiceQ+ENkM8ZHsv0yc9q8ZgZX5KR3ghG0j7wONDdgv
UOGuHNbO2QPA2d38V+xdwGkr/M8eep2xjYwDqT8+s7F+7BZeRThF2s9NBhE4rgob
KlPXwYTqkx5fiODtlFE9igryi/aSr9iaVIVCOs9ZBwQrETc/WLttWbfMgrMWFW5z
r4sa/84oVe0GVwZ+KPJKjUpXR4x1C3O+vSIAREsZfBDfjADHvGgXyRCYw+xrnq4=
=9kOH
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2019-02-19' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2019-02-19
This series includes misc updates to mlx5 drivers and one ethtool update.
1) From Aya Levin:
- ethtool: Define 50Gbps per lane link modes
- add support for 50Gbps per lane link modes in mlx5 driver
2) From Tariq Toukan,
- Add a helper function to unify mlx5 resource reloading
3) From Vlad Buslov,
- Remove wrong and superfluous tc pedit header type check
4) From Tonghao Zhang,
- Some refactoring in en_tc.c to simplify the mlx5e_tc_add_fdb_flow
5) From Leon Romanovsky & Saeed,
- Compilation warning fixes
6) From Bodong wang,
- E-Switch fixes that are related to the SmarNIC series
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Booting 4.20 on SolidRun Clearfog issues this warning with DMA API
debug enabled:
WARNING: CPU: 0 PID: 555 at kernel/dma/debug.c:1230 check_sync+0x514/0x5bc
mvneta f1070000.ethernet: DMA-API: device driver tries to sync DMA memory it has not allocated [device address=0x000000002dd7dc00] [size=240 bytes]
Modules linked in: ahci mv88e6xxx dsa_core xhci_plat_hcd xhci_hcd devlink armada_thermal marvell_cesa des_generic ehci_orion phy_armada38x_comphy mcp3021 spi_orion evbug sfp mdio_i2c ip_tables x_tables
CPU: 0 PID: 555 Comm: bridge-network- Not tainted 4.20.0+ #291
Hardware name: Marvell Armada 380/385 (Device Tree)
[<c0019638>] (unwind_backtrace) from [<c0014888>] (show_stack+0x10/0x14)
[<c0014888>] (show_stack) from [<c07f54e0>] (dump_stack+0x9c/0xd4)
[<c07f54e0>] (dump_stack) from [<c00312bc>] (__warn+0xf8/0x124)
[<c00312bc>] (__warn) from [<c00313b0>] (warn_slowpath_fmt+0x38/0x48)
[<c00313b0>] (warn_slowpath_fmt) from [<c00b0370>] (check_sync+0x514/0x5bc)
[<c00b0370>] (check_sync) from [<c00b04f8>] (debug_dma_sync_single_range_for_cpu+0x6c/0x74)
[<c00b04f8>] (debug_dma_sync_single_range_for_cpu) from [<c051bd14>] (mvneta_poll+0x298/0xf58)
[<c051bd14>] (mvneta_poll) from [<c0656194>] (net_rx_action+0x128/0x424)
[<c0656194>] (net_rx_action) from [<c000a230>] (__do_softirq+0xf0/0x540)
[<c000a230>] (__do_softirq) from [<c00386e0>] (irq_exit+0x124/0x144)
[<c00386e0>] (irq_exit) from [<c009b5e0>] (__handle_domain_irq+0x58/0xb0)
[<c009b5e0>] (__handle_domain_irq) from [<c03a63c4>] (gic_handle_irq+0x48/0x98)
[<c03a63c4>] (gic_handle_irq) from [<c0009a10>] (__irq_svc+0x70/0x98)
...
This appears to be caused by mvneta_rx_hwbm() calling
dma_sync_single_range_for_cpu() with the wrong struct device pointer,
as the buffer manager device pointer is used to map and unmap the
buffer. Fix this.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a few PCI ID'S for 22000 and killer series in addition to
chainging the marketing name.
Signed-off-by: Ihab Zhaika <ihab.zhaika@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Implement Rx fifos dump in the new dump mechanism.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Implement Tx fifos dump in the new dump mechanism.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add iwl_fw_ini_region_cfg region struct to fill_header handler of
iwl_dump_ini_mem_ops. it is needed for future support in fifos dumping.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Make fill_range handler of iwl_dump_ini_mem_ops accept a generic range
pointer. It is needed for future support in fifos dumping.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Make the get size handler of iwl_dump_ini_mem_ops include the total
size of the region. It is needed for fifos dumping.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add informative print in case the range is not available.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The driver sets ignore_consec to -1 which is 0xffffffff in u32
so when iwl_fw_ini_trigger_on is called, it will always return false
and each trigger could be used only once.
Solve this by removing the assignment to -1.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Fixes: fe1b7d6c28 ("iwlwifi: add support for triggering ini triggers")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
After the FW image was loaded for the first time,
fwrt->smem_cfg.num_lmacs value will no longer be zero since we don't
clean it when we stop the device. So if we load the image once and then
we fail on a consecutive attempt, the driver will abort any dumping.
Solve this by removing the condition. It is safe to remove since
when we do the actual dumping in iwl_fw_dbg_collect_sync we check
that STATUS_DEVICE_ENABLED bit is still active.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For non-offloaded rate control, implement VHT extended NSS
support by just ignoring 160 MHz on transmit if the peer
doesn't support the full NSS (2). This is pretty unlikely
and gets us 160 MHz RX as well as TX in most cases, since
the typical case for this workaround is 4x4 AP only doing
2x2 on 160 MHz.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When hostapd sends a probe response, it does not request an
acknowledgment on the probe response. This setting is propagated
to the driver and FW from mac80211, and as a result probe responses
are transmitted only once without retries. In congested
environments, this reduces the likelihood for finding the AP.
To overcome this, enable acknowledgment and retries for probe
responses, even in case no acknowledgment is requested. In such
a case the retry limit is set to 3.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's no point in this, we already do everything in a nested
fashion, and if we didn't we'd already crash in iwl_mvm_leds_exit()
etc. Just remove the bit.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Previously the protection flag wasn't set on multicast frames even if
the RA is unicast. Fix this by checking addr1 instead.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add an option to not send beacons and probe responses. This is
used for testing multiple-bssid.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Return the AID currently set when reading this debugfs entry.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Verify we do not accept new beacon templates while beacon
injection is active.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Intel Linux Wireless <linuxwifi@intel.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Intel Linux Wireless <linuxwifi@intel.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Intel Linux Wireless <linuxwifi@intel.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We support this, so we should advertise it. In fact, if we don't,
mac80211 will do it for us (as we advertise SUPPORTS_VHT_EXT_NSS_BW
to it), but that requires a memory reallocation which is wasteful:
ieee80211 phy0: copying sband (band 1) due to VHT EXT NSS BW flag
Set the flag here to avoid that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The IWL_MVM_INIT_STATUS_REG_HW_INIT_COMPLETE bit shouldn't be set,
and realistically we should complete all setup before we call the
ieee80211_register_hw() function. Fix this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
One of the more common cases of allocation size calculations is finding the
size of a structure that has a zero-sized array at the end, along with memory
for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = kzalloc(sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can now
use the new struct_size() helper:
instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL);
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
One of the more common cases of allocation size calculations is finding the
size of a structure that has a zero-sized array at the end, along with memory
for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = kzalloc(sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can now
use the new struct_size() helper:
instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL);
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
With CONFIG_NO_AUTO_INLINE, we run into a silly warning when
gcc fails to remember that n_profiles is constant across
the function call to iwl_mvm_sar_set_profile:
drivers/net/wireless/intel/iwlwifi/mvm/fw.c: In function 'iwl_mvm_sar_get_ewrd_table':
drivers/net/wireless/intel/iwlwifi/mvm/fw.c:746:9: error: 'ret' may be used uninitialized in this function [-Werror=maybe-uninitialized]
Marking that function 'inline' avoids the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In case mac80211 was requested to perform an HW restart, but the HW
restart has not started yet, there is no need to request another one.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
AX210 devices assume that the (DRAM) addresses of the rb_stts's for
the different queues are continuous.
So allocate the rb_stts's for all the Rx queues in one place.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
ath.git patches for 5.1. Major changes:
ath10k
* support WPA3 with WCN3990
* support for mac80211 airtime fairness based on transmit rate
estimation, the firmware needs to support WMI_SERVICE_PEER_STATS to
enable this
* report transmit airtime to mac80211 with firmwares having
WMI_SERVICE_REPORT_AIRTIME feature, this to have more accurate
airtime fairness based on real transmit time (instead of just
estimated from transmit rate)
* support Fine Timing Measurement (FTM) responder role
* add dynamic VLAN support with firmware having
WMI_SERVICE_PER_PACKET_SW_ENCRYPT
* switch to use SPDX license identifiers
The start() callback is too late for this: NetworkManager would already
have seen the hardware, thinking 00:00:00:00:00:00 is its permanent
address.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-by: Steve deRosier <derosier@cal-sierra.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In order to be able to get a MAC address before we register the device
with ieee80211 we'll need to load the firmware way earlier.
There seems to be one problem with this: the device seems to start
with radio enabled and starts sending in frames right after the firmware
load finishes. Disable the radio as soon as possible.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-by: Steve deRosier <derosier@cal-sierra.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We'll need to talk to the firmware to get a hardware address before
device is registered with ieee80211 subsystem at the end of
lbtf_add_card(). Hooking the callbacks after that is too late.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
While experimenting with firmware loading I ended up in a state of
firmware reporting shared RAM address 0x04000001. It was causing:
[ 94.448015] Unable to handle kernel paging request at virtual address cd680001
due to reading out of the mapped memory.
This patch adds some basic validation to avoid kernel crashes due to the
unexpected firmware behavior.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is an uppercase 'N' that should be a lowercase 'n', fix this.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This recently added macro provides more meaningful error messages thanks
to identifying a specific wiphy. It's especially important on systems
with few cards supported by the same (brcmfmac) driver.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use SPDX identifiers everywhere in ath10k.
Makefile was incorrectly marked in commit b24413180f ("License cleanup: add
SPDX GPL-2.0 license identifier to files with no license"), fix that as well.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Another platform requires even longer delay to make the device work
correctly after S3.
So increase the delay to 300ms.
BugLink: https://bugs.launchpad.net/bugs/1798921
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Passing the struct ptp_clock_info caps by parameter is passing over 130 bytes
of data by value on the stack. Optimize this by passing it by reference instead.
Also shinks the object code size:
Before:
text data bss dec hex filename
12596 2160 64 14820 39e4 drivers/ptp/ptp_qoriq.o
After:
text data bss dec hex filename
12567 2160 64 14791 39c7 drivers/ptp/ptp_qoriq.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When disabling vport, relevant vport configurations will be cleaned
up. These cleanups should be done to the vports which had these configs
applied at vport enablement. As esw manager vport didn't have such
vport config applied, cleanup should not touch it.
Fixes: de9e6a8136c5 ("net/mlx5: E-Switch, Properly refer to host PF vport as other vport")
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reported-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When eswitch gets vport data structure, the index should not be out
of the range of the vport array. Driver mistakenly used vport number
to check the range.
Fixes: 22b8ddc86bf4 ("net/mlx5: E-Switch, Assign a different position for uplink rep and vport")
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
fpga_qpn was assigned but never used and compilation with W=1
produced the following warning:
drivers/net/ethernet/mellanox/mlx5/core/fpga/core.c: In function _mlx5_fpga_event_:
drivers/net/ethernet/mellanox/mlx5/core/fpga/core.c:320:6: warning:
variable _fpga_qpn_ set but not used [-Wunused-but-set-variable]
u32 fpga_qpn;
^~~~~~~~
Fixes: 98db16bab5 ("net/mlx5: FPGA, Handle QP error event")
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Compilation with W=1 produces following warning:
drivers/net/ethernet/mellanox/mlx5/core/en/monitor_stats.c:69:6:
warning: no previous prototype for _mlx5e_monitor_counter_start_ [-Wmissing-prototypes]
void mlx5e_monitor_counter_start(struct mlx5e_priv *priv)
^~~~~~~~~~~~~~~~~~~~~~~~~~~
Avoid it by declaring mlx5e_monitor_counter_start() as a static function.
Fixes: 5c7e8bbb02 ("net/mlx5e: Use monitor counters for update stats")
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This patch is a little improvement. Simplify the mlx5e_tc_add_fdb_flow().
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
With recent introduction of flow_rule infrastructure drivers no longer
directly include action headers, so it is no longer possible to use
constants defined in them. Instead, one of flow_rule patches substituted
pedit action header constant with hardcoded value '2' in mlx5
set_pedit_val() function conditional which verifies that header type is in
range of values allowed by pedit action. That conditional is now both
wrong (hardcoded value is '2' but __PEDIT_HDR_TYPE_MAX is 6 in current
version) and superfluous (pedit action already verifies that header type is
in allowed range during init). Remove the described check from mlx5 code.
Fixes: 7386788175 ("drivers: net: use flow action infrastructure")
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Dmytro Linkin <dmitrolin@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Take into a function the common code structure of opening
a side set of channels followed by a call to apply them.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In previous patch, driver added new speed modes: 50Gbps per lane support
for 50G/100G/200G. This patch modifies mlx5e_get_link_ksettings and
mlx5e_set_link_ksettings to set and get these link modes via ethtool.
In order to do so, added mapping of new HW bits to ethtool bitmap and
enforce mutual exclusion between extended link modes and previously
defined link modes.
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This patch is to do code cleanup for ns83820_probe_phy().
It deletes unused variable 'first', commented out code,
and the pointless 'for' loop.
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
RGMII_ID specifies that we should have internal delay, so resurrect the
delay addition routine but under the RGMII_ID mode.
Fixes: 40269aa9f40a ("net: dsa: qca8k: disable delay for RGMII mode")
Tested-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver returns -ENOSPC when tc_can_offload() check fails. Since that
routine checks for flow parameters that are not supported by the driver,
we should return the more appropriate -EOPNOTSUPP.
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for SIOCGMIIREG and SIOCSMIIREG ioctls to
mdio read/write to external PHY.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer firmware understands the concept of a trusted VF, so propagate the
trusted VF attribute set by the PF admin. to the firmware. Also, check
the firmware trusted setting when considering the VF MAC address change
and reporting the trusted setting to the user.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for BCM957504 with device ID 1751
Signed-off-by: Erik Burrows <erik.burrows@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware error recover is the major change in this spec.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We do not need separate lines for calculating register values.
Also add comment that value is different than in vendor driver.
Suggested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The TX_PIN_CFG_RFRX_EN bit was not set on other devices than MT7620,
restore old behavaviour since setting this bit maight not be
correct for older devices.
Fixes: 41977e86c9 ("rt2x00: add support for MT7620")
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Do not enable TX_PIN_CFG_LNA_PE_A* bits for 2.4GHz band and
vice versa TX_PIN_CFG_LNA_PE_G* bits for 5GHz.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Register 66 was causing issues on RT6352 if set to the same value as
in MTK driver. With 1c reg value device was working fine in both HT20
and HT40 modes.
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remove band check from rf53xx channel config routine since all chips
using it are single band.
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The parameter order for clamp is supposed to be clamp(value, low, high).
When we write it in this order it's equivalent to
min(head->plcp[3] & 0x7f, 75) which works in this context where the min
is zero. But it's not a correct use of the API.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/realtek/rtl818x/rtl8180/dev.c: In function 'rtl8180_probe':
drivers/net/wireless/realtek/rtl818x/rtl8180/dev.c:1727:15: warning:
variable 'io_addr' set but not used [-Wunused-but-set-variable]
drivers/net/wireless/realtek/rtl818x/rtl8180/dev.c:1726:16: warning:
variable 'mem_addr' set but not used [-Wunused-but-set-variable]
They're never used since introduction.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Replace hard coded function name with __func__, to
improve robustness and to conform to the Linux kernel coding
style. Issue found using checkpatch.
Signed-off-by: Keyur Patel <iamkeyur96@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As it is, doing something like
# iw phy phy0 interface add foobar type ibss
on a firmware that doesn't have ad-hoc support just yields failures of
HostCmd_CMD_SET_BSS_MODE, which happened to return a '-1' error code
(-EPERM? not really right...) and sometimes may even crash the firmware
along the way.
Let's parse the firmware capability flag while registering the wiphy, so
we don't allow attempting IBSS at all, and we get a proper -EOPNOTSUPP
from nl80211 instead.
Fixes: e267e71e68 ("mwifiex: Disable adhoc feature based on firmware capability")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
NL80211_TX_POWER_LIMITED was treated as NL80211_TX_POWER_AUTOMATIC,
which is the opposite of what should happen and can cause nasty
regulatory problems.
if/else converted to a switch without default to make gcc warn
on unhandled enum values.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/marvell/libertas_tf/main.c: In function 'lbtf_rx':
drivers/net/wireless/marvell/libertas_tf/main.c:554:15: warning:
variable 'flags' set but not used [-Wunused-but-set-variable]
It never used and can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Steve deRosier <derosier@cal-sierra.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Instead of exposing the signal-to-noise ration, calculate the actual signal
level taking the noise floor into account.
Also, flip the SIGNAL_DBM bit on, so that mac80211 exposes the signal
level along with the station info in scan results. This fills
NetworkManager's "nmcli d wifi output" output with colors, bars and joy.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-by: Steve deRosier <derosier@cal-sierra.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Also, turn it to a dev_info() to make checkpatch.pl happy.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-by: Steve deRosier <derosier@cal-sierra.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It doesn't make sense and the USB core warns on each submit of such
URB, easily flooding the message buffer with tracebacks.
Analogous issue was fixed in regular libertas driver in commit 6528d88047
("libertas: don't set URB_ZERO_PACKET on IN USB transfer").
Cc: stable@vger.kernel.org
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-by: Steve deRosier <derosier@cal-sierra.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Logging each and every command response is way too much for INFO level.
Silence this, unless CONFIG_LIBERTAS_THINFIRM_DEBUG has been enabled.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-by: Steve deRosier <derosier@cal-sierra.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/rsi/rsi_91x_main.c: In function 'rsi_prepare_skb':
drivers/net/wireless/rsi/rsi_91x_main.c:127:24: warning:
variable 'vif' set but not used [-Wunused-but-set-variable]
drivers/net/wireless/rsi/rsi_91x_main.c:124:28: warning:
variable 'info' set but not used [-Wunused-but-set-variable]
They're not used any more since 160ee2a11c ("rsi: fill rx_params only once.")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Trivial fixes to spelling mistakes in various files in rsi folder.
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is a \b (backspace) character in the message that wasn't intended.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/usb.c: In function 'brcmf_usb_state_change':
drivers/net/wireless/broadcom/brcm80211/brcmfmac/usb.c:578:6: warning:
variable 'old_state' set but not used [-Wunused-but-set-variable]
It's never used and can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This macro will be used in more places not just the cfg80211.c. It makes
sense to pass some common struct to it as "struct wiphy" is mostly
referenced in cfg80211 code only.
A very common one (used above the bus abstraction layer) is struct
brcmf_pub. Many functions already keep reference to it which will make
using bphy_err() simpler. It should also allow extending that macro's
logic if it's ever needed.
This improves code recently added in the commit 3ef005b82e ("brcmfmac:
add bphy_err() and use it in the cfg80211.c").
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
So far 160 MHz channels were treated as 20 MHz ones which was breaking
support for 40/80 MHz due to the brcmf_construct_chaninfo() logic and
its assumptions.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
1) Use switch to simplify/improve the code & avoid some duplication
2) Add warning for unsupported values
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware is capable of reporting ring status. It's used e.g. to signal
some problem with a specific ring setup. This patch adds support for
printing ring & error number which may be useful for debugging setup
issues.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
