Commit Graph

9772 Commits

Author SHA1 Message Date
John W Linville
83840e4bd5 i40e: avoid use of uninitialized v_budget in i40e_init_msix
This I40E_FCOE block increments v_budget before it has been initialized,
then v_budget gets overwritten a few lines later.  This patch just
reorders the code hunks in what I believe was the intended sequence.

Coverity: CID 1260099

Signed-off-by: John W Linville <linville@tuxdriver.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-02-08 19:01:06 -08:00
Rickard Strandqvist
cf86da489d i40e: i40e_fcoe.c: Remove unused function
Remove the function i40e_rx_is_fip() that is not used anywhere.

This was partially found by using a static code analysis program
called cppcheck.

Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-02-08 18:45:17 -08:00
Hariprasad Shenai
bad4379263 cxgb4: Add support in debugfs to dump the congestion control table
Dump Transport Processor modules congestion control configuration

Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-02-07 22:52:39 -08:00
Hariprasad Shenai
bf7c781d57 cxgb4: Add support to dump mailbox content in debugfs
Adds support to dump the current contents of mailbox and the driver which owns
it.

Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-02-07 22:52:39 -08:00
Hariprasad Shenai
797ff0f573 cxgb4: Add support for ULP RX logic analyzer output in debugfs
Dump Upper Layer Protocol RX module command trace

Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-02-07 22:52:39 -08:00
Hariprasad Shenai
2d277b3b44 cxgb4: Added support in debugfs to display TP logic analyzer output
Dump Transport Processor event trace.

Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-02-07 22:52:39 -08:00
Hariprasad Shenai
70a5f3bb5f cxgb4: Add support in debugfs to display sensor information
Dump out various chip sensor information. Currently Chip Temperature
and Core Voltage.

Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-02-07 22:52:39 -08:00
Sathya Perla
f986afcbe0 be2net: avoid unncessary swapping of fields in eth_tx_wrb
The 32-bit fields of a tx-wrb are little endian. The driver is currently
using be_dws_le_to_cpu() routine to swap (cpu to le) all the fields of
a tx-wrb. So, the rsvd field is also unnecessarily swapped.

This patch fixes this by individually swapping the required fields.
Also, the type of the fields in eth_tx_wrb{} is now changed to __le32
from u32 to avoid sparse warnings.

Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-02-07 22:50:59 -08:00
Vasundhara Volam
21252377bb be2net: process port misconfig async event
This patch adds support for processing the port misconfigure async
event generated by the FW. This event is generated typically when an
optical module is incorrectly installed or is faulty.

This patch also moves the port_name field to the adapter struct for
logging the event. As the be_cmd_query_port_name() call is now moved
to be_get_config(), it is modified to use the mailbox instead of MCCQ

Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-02-07 22:50:59 -08:00
Sathya Perla
f66b7cfd95 be2net: refactor be_set_rx_mode() and be_vid_config() for readability
This patch re-factors the filter setting (uc-list, mc-list, promisc, vlan)
code in be_set_rx_mode() and be_vid_config() to make it more readable
and reduce code duplication.
This patch adds a separate field to track the state/mode of filtering,
along with moving all the filtering related fields to one place in be
be_adapter structure.

Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-02-07 22:50:59 -08:00
Sathya Perla
ac34b74378 be2net: remove duplicate code in be_cmd_rx_filter()
This patch passes BE_IF_FLAGS_XXX flags to be_cmd_rx_filter() routine
instead of the IFF_XXX flags. Doing this gets rid of the code to convert
the IFF_XXX flags to the BE_IF_FLAGS_XXX used by the FW cmd. The patch
also removes code for setting if_flags_mask that was duplicated for each
filter mode.

Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-02-07 22:50:58 -08:00
Vasundhara Volam
70a7b52570 be2net: use offset based FW flashing for Skyhawk chip
While sending FW update cmds to the FW, the driver specifies the "type"
of each component that needs to be flashed. The FW then picks the offset
in the flash area at which the componnet is to be flashed. This doesn't work
when new components that the current FW doesn't recognize, need to be
flashed. Recent FWs (10.2 and above) support a scheme of FW-update wherein
the "offset" of the component in the flash area can be specified instead
of the "type". This patch uses the "offset" based FW-update mechanism and
only when it fails, it fallsback to the old "type" based update.

Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-02-07 22:50:58 -08:00
Vasundhara Volam
81a9e226ff be2net: avoid flashing SH-B0 UFI image on SH-P2 chip
Skyhawk-B0 FW UFI is not compatible to flash on Skyhawk-P2 ASIC.
But, Skyhawk-P2 FW UFI is compatible with both B0 and P2 chips.

Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-02-07 22:50:58 -08:00
Vasundhara Volam
5d3acd0d16 be2net: refactor code that checks flash file compatibility
This patch re-factors the code that checks for flash file compatibility with
the chip type, for better readability, as follows:
	- be_get_ufi_type() returns the UFI type from the flash file
	- be_check_ufi_compatibility() checks if the UFI type is compatible
	  with the adapter/chip that is being flashed

Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-02-07 22:50:58 -08:00
Vasundhara Volam
83b0611699 be2net: replace (1 << x) with BIT(x)
BIT(x) is the preffered usage.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>

Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-02-07 22:50:57 -08:00
Sathya Perla
f7062ee5e4 be2net: move un-exported routines from be.h to respective src files
Routines that are called only inside one src file must remain in that
file itself. Including them in a header file that is used for exporting
routine/struct definitions, causes unnecessary compilation of other
src files, when such a routine is modified.

Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-02-07 22:50:57 -08:00
Lendacky, Thomas
fd972b736b amd-xgbe: Check per channel DMA interrupt use in main ISR
When using per channel DMA interrupts the transmit interrupt (TI) and the
receive interrupt (RI) are masked off so as to not generate an interrupt
to the main ISR. However, should another interrupt fire for the DMA channel
that is handled by the main ISR the TI/RI bits can still be set. This
will cause the wrong and uninitialized napi structure to be used causing a
panic. Add a check to be sure per channel DMA interrupts are not enabled
before acting on those bit flags.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-02-07 22:44:42 -08:00
Dan Carpenter
37c85c3498 net: sxgbe: fix error handling in init_rx_ring()
There are a couple bugs with the error handling in this function.

1) If we can't allocate "rx_ring->rx_skbuff" then we should call
   dma_free_coherent() but we don't.
2) free_rx_ring() frees "rx_ring->rx_skbuff_dma" and "rx_ring->rx_skbuff"
   so calling it in a loop causes a double free.

Also it was a bit confusing how we sometimes freed things before doing
the goto.  I've cleaned it up so it does error handling in normal kernel
style.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-02-06 12:50:12 -08:00
Don Skidmore
5b7f000ff9 ixgbe: add Tx anti spoofing support
This patch enables the ethertype Anti-Spoofing feature for affected
devices. It is configured such that LLDP packets sent by a VF will
be dropped.

Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-02-05 19:58:46 -08:00
Emil Tantilov
9ac5c5ccdb ixgbevf: combine all of the tasks into a single service task
This change combines the reset and watchdog tasklets into a single task.

The advantage of this is that we can avoid multiple schedules of the reset
task when we have a reset event needed due to either the mailbox going down
or transmit packets being present on a link down.

CC: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-02-05 19:58:45 -08:00
Emil Tantilov
e66c92ad58 ixgbevf: rewrite watchdog task to function similar to igbvf
This patch cleans up the logic dealing with link down/up by breaking down the
link detection and up/down events into separate functions - similar to how these
events are handled in other drivers.

CC: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-02-05 19:58:45 -08:00
Emil Tantilov
e08400b707 ixgbevf: Add code to check for Tx hang
This patch adds code to allow for Tx hang checking.  The idea is to provide
more robust debug info in the event of a transmit unit hang. Similar to the
logic in ixgbe.

CC: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-02-05 19:58:44 -08:00
Emil Tantilov
d9bdb57f9c ixgbevf: Fix ordering of shutdown to correctly disable Rx and Tx
This patch updates the ordering of the shutdown path so that we attempt to
shutdown the rings more gracefully. Basically the big changes are that we
shutdown the main Rx filter in the case of Rx and we set the carrier_off
state in the case of Tx so that packets stop being delivered from outside
the driver.  Then we shut down interrupts and NAPI.  Finally we stop the
rings from performing DMA and clean them.  This is a bit more graceful than
the previous path.

CC: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-02-05 19:58:44 -08:00
Emil Tantilov
39f35a370b ixgbevf: set vlan_features in a single write instead of several ORs
Clean up the setting of vlan_features by enabling all features at once.

Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-02-05 19:58:42 -08:00
Don Skidmore
3f207800a9 ixgbe: add VXLAN offload support for X550 devices
Add support VXLAN receive checksum offload in X550 hardware.

Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-02-05 19:57:49 -08:00
Don Skidmore
4dedadcbae ixgbe: Cleanup probe to remove redundant attempt to ID PHY
We always identify the PHY in our reset_hw path anyway so there is
no need to do it in get_invariants().  The reason I even noticed this
is that for new hardware (X550em) we don't assign some methods until
later in probe and calling phy.ops.read_reg could lead to a panic.

Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-02-05 19:57:48 -08:00
Don Skidmore
f9c9e488ce ixgbe: cleanup redundant default method set_rxpba
My original patch 6a14ee0cfb "ixgbe: Add X550 support function pointers"
accidental set a default value for this structure member twice.

Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-02-05 19:57:48 -08:00
Emil Tantilov
42ce2c8ef6 ixgbe: fix setting port VLAN
This patch fixes couple of issues introduced by
commit 2b509c0cd2 ("ixgbe: cleanup ixgbe_ndo_set_vf_vlan")

- fix setting of the VLAN inside ixgbe_enable_port_vlan()
- disable the "hide VLAN" bit in PFQDE when port VLAN is disabled

Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-02-05 19:57:47 -08:00
Emil Tantilov
9295edb472 ixgbevf: add RSS support for X550
X550 provides RSS registers for configuring RSS per VF.

This patch introduces ixgbevf_setup_vfmrqc() which uses the VFRETA,
VFRSSRK and VFMRQC registers to configure RSS on X550.

Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-02-05 19:57:47 -08:00
Emil Tantilov
2dc571aa61 ixgbevf: enable multiple queue support
This patch enables multiple queues and RSS support for the VF.
Maximum of 2 queues are supported due to available vectors.

Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-02-05 19:57:46 -08:00
Emil Tantilov
dec2e395fd ixgbe: allow multiple queues in SRIOV mode
ixgbe_set_sriov_queues() has the logic to allow multiple queues, this patch
just removes the limitation.

Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-02-05 19:57:46 -08:00
Don Skidmore
7ddbde3f74 ixgbe: cleanup sparse errors in new ixgbe_x550.c file
This patch cleans up prototypes that should have been defined
as static.

Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-02-05 19:41:51 -08:00
Matthew Vick
f4a80f1ef7 fm10k: Resolve compile warnings with W=1
Fix two cases where variables are being set but not used.

Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Krishneil Singh<Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-02-05 19:41:51 -08:00
Matthew Vick
33a44c2873 fm10k: Validate VLAN ID in fm10k_update_xc_addr_pf
Currently, fm10k_update_xc_addr_pf has an issue where it does not
properly drop the upper-most four bits of the VLAN ID due to type
promotion. Resolve the issue not by masking off the bits, but by
throwing an error if the VLAN ID is out-of-bounds.

Reported-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-02-05 19:41:50 -08:00
Lad, Prabhakar
2ca292d968 vxge: fix sparse warning
this patch fixes following sparse warning:

vxge-config.c:4640:30: warning: Using plain integer as NULL pointer

Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-02-05 16:07:06 -08:00
Lad, Prabhakar
8093b1c313 net/macb: fix sparse warning
this patch fixes following sparse warning:

macb.c:2038:26: warning: symbol 'gem_ethtool_ops' was not declared. Should it be static?

Alongside drops exporting of gem_ethtool_ops as there is no need.

Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-02-05 16:03:28 -08:00
Lad, Prabhakar
1444c301a4 net: bnx2x: fix sparse warnings
this patch fixes following sparse warnings:

bnx2x_main.c:9172:6: warning: symbol 'bnx2x_stop_ptp' was not declared. Should it be static?
bnx2x_main.c:13321:6: warning: symbol 'bnx2x_register_phc' was not declared. Should it be static?
bnx2x_main.c:14638:5: warning: symbol 'bnx2x_enable_ptp_packets' was not declared. Should it be static?

Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-02-05 16:03:28 -08:00
Lad, Prabhakar
57ae84a009 enic: enic_main: fix sparse warnings
this patch fixes following sparse warnings:

enic_main.c:92:28: warning: symbol 'mod_table' was not declared. Should it be static?
enic_main.c:109:28: warning: symbol 'mod_range' was not declared. Should it be static?
enic_main.c:1306:5: warning: symbol 'enic_busy_poll' was not declared. Should it be static?

Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-02-05 16:03:27 -08:00
Lad, Prabhakar
a20667bf7d enic: enic_ethtool: fix sparse warning
this patch fixes following sparse warning:

enic_ethtool.c:95:6: warning: symbol 'enic_intr_coal_set_rx' was not declared. Should it be static?

Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-02-05 16:03:27 -08:00
Lad, Prabhakar
bc0ee16373 be2net: fix sparse warning
this patch fixes following sparse warning:

be_cmds.c:2750:5: warning: symbol 'be_cmd_set_qos' was not declared. Should it be static?

Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-02-05 16:03:27 -08:00
Lad, Prabhakar
4a95b6d0a7 chelsio: cxgb4: fix sparse warning
this patch fixes following sparse warning:

cxgb4_dcb.c:25:6: warning: symbol 'dcb_ver_array' was not declared. Should it be static?

Alongside making it const.

Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-02-05 16:03:27 -08:00
David S. Miller
6e03f896b5 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Conflicts:
	drivers/net/vxlan.c
	drivers/vhost/net.c
	include/linux/if_vlan.h
	net/core/dev.c

The net/core/dev.c conflict was the overlap of one commit marking an
existing function static whilst another was adding a new function.

In the include/linux/if_vlan.h case, the type used for a local
variable was changed in 'net', whereas the function got rewritten
to fix a stacked vlan bug in 'net-next'.

In drivers/vhost/net.c, Al Viro's iov_iter conversions in 'net-next'
overlapped with an endainness fix for VHOST 1.0 in 'net'.

In drivers/net/vxlan.c, vxlan_find_vni() added a 'flags' parameter
in 'net-next' whereas in 'net' there was a bug fix to pass in the
correct network namespace pointer in calls to this function.

Signed-off-by: David S. Miller <davem@davemloft.net>
2015-02-05 14:33:28 -08:00
Markus Elfring
7af348be47 net: ep93xx_eth: Delete unnecessary checks before the function call "kfree"
The kfree() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.

This issue was detected by using the Coccinelle software.

Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-02-05 00:35:00 -08:00
Markus Elfring
7061b2bdd6 qlogic: Deletion of unnecessary checks before two function calls
The functions kfree() and vfree() perform also input parameter validation.
Thus the test around their calls is not needed.

This issue was detected by using the Coccinelle software.

Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-02-05 00:30:12 -08:00
Lad, Prabhakar
f86b4ae6ac net: ethernet: ti/cpsw-common.c: fix sparse warning
this patch fixes following sparse warning:

cpsw-common.c:23:5: warning: symbol 'cpsw_am33xx_cm_get_macid' was not declared. Should it be static?

Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-02-05 00:27:49 -08:00
Markus Elfring
de7017625e netxen: Delete an unnecessary check before the function call "kfree"
The kfree() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.

This issue was detected by using the Coccinelle software.

Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-02-05 00:26:23 -08:00
Markus Elfring
1b4b32c6b8 net: fec: Delete unnecessary checks before the function call "kfree"
The kfree() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.

This issue was detected by using the Coccinelle software.

Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-02-05 00:26:04 -08:00
Markus Elfring
2d4ad4f690 myri10ge: Delete an unnecessary check before the function call "kfree"
The kfree() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.

This issue was detected by using the Coccinelle software.

Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-02-05 00:25:10 -08:00
Shahed Shaikh
f31ec95fa1 qlcnic: Fix NAPI poll routine for Tx completion
After d75b1ade56 ("net: less interrupt masking in NAPI")
driver's NAPI poll routine is expected to return
exact budget value if it wants to be re-called.

Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Fixes: d75b1ade56 ("net: less interrupt masking in NAPI")
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-02-05 00:24:08 -08:00
Markus Elfring
0b5b6beea1 cxgb4: Delete an unnecessary check before the function call "release_firmware"
The release_firmware() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.

This issue was detected by using the Coccinelle software.

Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-02-05 00:06:47 -08:00
Hariprasad Shenai
3a336cb171 cxgb4: Add low latency socket busy_poll support
cxgb_busy_poll, corresponding to ndo_busy_poll, gets called by the socket
waiting for data.

With busy_poll enabled, improvement is seen in latency numbers as observed by
collecting netperf TCP_RR numbers.
Below are latency number, with and without busy-poll, in a switched environment
for a particular msg size:
netperf command: netperf -4 -H <ip> -l 30 -t TCP_RR -- -r1,1
Latency without busy-poll: ~16.25 us
Latency with busy-poll   : ~08.79 us

Based on original work by Kumar Sanghvi <kumaras@chelsio.com>

Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-02-04 23:55:58 -08:00
Lendacky, Thomas
cf180b8acf amd-xgbe: Set RSS enablement based on hardware features
The RSS support requires enablement based on the features reported by
the hardware. The setting of this flag is missing. Add support to
set the RSS enablement flag based on the reported hardware features.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-02-04 20:31:51 -08:00
Markus Elfring
9b55669c14 NetCP: Deletion of unnecessary checks before two function calls
The functions cpsw_ale_destroy() and of_dev_put() test whether their argument
is NULL and then return immediately. Thus the test around the call
is not needed.

This issue was detected by using the Coccinelle software.

Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-02-04 20:29:47 -08:00
Markus Elfring
f339664c0b IBM-EMAC: Delete an unnecessary check before the function call "of_dev_put"
The of_dev_put() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.

This issue was detected by using the Coccinelle software.

Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-02-04 20:29:47 -08:00
Lendacky, Thomas
211fcf6d21 amd-xgbe: Adjust for zero-based traffic class count
The number of traffic classes reported by the hardware is zero-based
so increment the value returned to get an actual count.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-02-04 20:28:14 -08:00
Ido Shamay
cfb53f36a5 net/mlx4_en: Notify TX Vlan offload change
Notify users when TX vlan offload feature changed with ethtool.
Relevant command - ethtool -K <eth> txvlan on/off.

Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-02-04 16:17:46 -08:00
Ido Shamay
e8e7f018f1 net/mlx4_en: Adjust RX frag strides to frag sizes
This patch improves memory utilization and therefore the packets rate
for special MTU's. Instead of setting the frag_stride to the maximal
hard coded frag_size, use the actual frag_size that is set according to
the MTU, when setting the stride of the last frag.
So, for example, for MTU 1600, where the frag_size of the 2nd frag is
86, the frag_size is set to 128 instead of 4096. See below:

Before:
 frag:0 - size:1536 prefix:0 stride:1536
 frag:1 - size:86 prefix:1536 stride:4096

 frag 0 allocator: - size:32768 frags:21
 frag 1 allocator: - size:32768 frags:8

After:
 frag:0 - size:1536 prefix:0 stride:1536
 frag:1 - size:86 prefix:1536 stride:128

 frag 0 allocator: - size:32768 frags:21
 frag 1 allocator: - size:32768 frags:256

Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-02-04 16:17:45 -08:00
Ido Shamay
b110d2ce49 net/mlx4_en: Print page allocator information
After Initialization of page_alloc, print actual allocated page
size and number of frags it contains. prints is done only when drv
message level is set on the interface.

Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-02-04 16:17:45 -08:00
Or Gerlitz
1c755cc5be net/mlx5_core: Move to use hex PCI device IDs
Align the IDs in the code with the modinfo, lspci -n, etc tools outputs.

Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-02-04 16:17:45 -08:00
Or Gerlitz
0fab541ac2 net/mlx4_core: Fix misleading debug print on CQE stride support
We do support cache line sizes of 32 and 64 bytes without activating the
CQE stride feature. Fix a misleading print saying that these cache line
sizes aren't supported.

Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-02-04 16:17:45 -08:00
Maor Gottlieb
6af0a52f65 net/mlx4: mlx4_config_dev_retrieval() - Initialize struct config_dev before using
Add Initialization to struct config_dev before filling and using it.
Fix to warning:

warning: config_dev.rx_checksum_val may be used uninitialized in this function

Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-02-04 16:17:45 -08:00
Maor Gottlieb
b332068ce4 net/mlx4_core: Fix mpt_entry initialization in mlx4_mr_rereg_mem_write()
a) Previously, mlx4_mr_rereg_write filled the MPT's start
   and length with the old MPT's values.
   Fixing the initialization to take the new start and length.

b) In addition access flags in mpt_status were initialized instead of
   status due to bad boolean operation. Fixing the operation.

c) Initialization of pd_slave caused a protection error.
   Fix - removing this initialization.

d) In resource_tracker.c: Fixing vf encoding to be one-based.

Fixes: e630664c ('mlx4_core: Add helper functions to support MR re-registration')
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-02-04 16:17:45 -08:00
Moni Shoua
5da0354726 net/mlx4_en: Port aggregation configuration
Capture NETDEV events generated by the bonding driver and based on that
make decisions of how to configure port aggregation in the mlx4 core driver.

This includes setting the V2P port table and re-creating the interested
interfaces in bonded/non-bonded mode.

Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-02-04 16:14:25 -08:00
Moni Shoua
53f33ae295 net/mlx4_core: Port aggregation upper layer interface
Supply interface functions to bond and unbond ports of a mlx4 internal
interfaces. Example for such an interface is the one registered by the
mlx4 IB driver under RoCE.

There are

1. Functions to go in/out to/from bonded mode
2. Function to remap virtual ports to physical ports

The bond_mutex prevents simultaneous access to data that keep status of
the device in bonded mode.

The upper mlx4 interface marks to the mlx4 core module that they
want to be subject for such bonding by setting the MLX4_INTFF_BONDING
flag. Interface which goes to/from bonded mode is re-created.

The mlx4 Ethernet driver does not set this flag when registering the
interface, the IB driver does.

Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-02-04 16:14:24 -08:00
Moni Shoua
59e14e3250 net/mlx4_core: Port aggregation low level interface
Implement the hardware interface required for port aggregation.

1. Disable RX port check on receive - don't perform a validity check
that matches to QP's port and the port where the packet is received.

2. Virtual to physical port remap - configure virtual to physical port
mapping. Port remap capability for virtual functions.

Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-02-04 16:14:24 -08:00
Nicholas Mc Guire
b5057dd79c tlan: msecs_to_jiffies convrsion
This is only an API consolidation and should make things more readable
it replaces var * HZ / 1000 by msecs_to_jiffies(var).

As there is a discrepancy between the code and the comments this is in
a separate patch.

Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-02-04 13:58:29 -08:00
Nicholas Mc Guire
51fd947149 tlan: use msecs_to_jiffies for conversion
This is only an API consolidation and should make things more readable
it replaces var * HZ / 1000 by msecs_to_jiffies(var).

Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-02-04 13:58:29 -08:00
Sanjeev Sharma
75300ad2d9 gianfar: correct the bad expression while writing bit-pattern
This patch correct the bad expression while writing the
bit-pattern from software's buffer to hardware registers.

Signed-off-by: Sanjeev Sharma <Sanjeev_Sharma@mentor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-02-04 13:55:24 -08:00
LEROY Christophe
4fc9b87bae net: fs_enet: Implement NETIF_F_SG feature
Freescale ethernet controllers have the capability to re-assemble fragmented
data into a single ethernet frame. This patch uses this capability and
implements NETIP_F_SG feature into the fs_enet ethernet driver.

On a MPC885, I get 53% performance improvement on a ftp transfer of a 15Mb file:
  * Without the patch : 2,8 Mbps
  * With the patch : 4,3 Mbps

Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-02-04 13:13:04 -08:00
Jack Morgenstein
5a2e87b168 net/mlx4_core: Fix kernel Oops (mem corruption) when working with more than 80 VFs
Commit de966c5928 (net/mlx4_core: Support more than 64 VFs) was meant to
allow up to 126 VFs.  However, due to leaving MLX4_MFUNC_MAX too low, using
more than 80 VFs resulted in memory corruptions (and Oopses) when more than
80 VFs were requested. In addition, the number of slaves was left too high.

This commit fixes these issues.

Fixes: de966c5928 ("net/mlx4_core: Support more than 64 VFs")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-02-02 19:38:04 -08:00
Anish Bhatt
ba0c39cb98 cxgb4 : Improve IEEE DCBx support, other minor open-lldp fixes
* Add support for IEEE ets & pfc api.
* Fix bug that resulted in incorrect bandwidth percentage being returned for
  CEE peers
* Convert pfc enabled info from firmware format to what dcbnl expects before
  returning

Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-02-02 18:54:35 -08:00
Arnd Bergmann
98830dd0fe net/tulip: don't warn about unknown ARM architecture
ARM has 32-byte cache lines, which according to the comment in
the init registers function seems to work best with the default
value of 0x4800 that is also used on sparc and parisc.

This adds ARM to the same list, to use that default but no
longer warn about it.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-02-02 18:53:34 -08:00
Arnd Bergmann
4c0c46be90 net: hip04: add missing MODULE_LICENSE
The hip04 ethernet driver causes a new compile-time warning
when built as a loadable module:

WARNING: modpost: missing MODULE_LICENSE() in drivers/net/ethernet/hisilicon/hip04_eth.o
see include/linux/module.h for more information

This adds the license as "GPL", which matches the header of the file.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-02-02 18:51:03 -08:00
David L Stevens
44ba582bea sunvnet: set queue mapping when doing packet copies
This patch fixes a bug where vnet_skb_shape() didn't set the already-selected
queue mapping when a packet copy was required. This results in using the
wrong queue index for stops/starts, hung tx queues and watchdog timeouts
under heavy load.

Signed-off-by: David L Stevens <david.stevens@oracle.com>
Acked-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-02-02 18:20:35 -08:00
Marcelo Leitner
61132bf7fb qlge: Fix qlge_update_hw_vlan_features to handle if interface is down
Currently qlge_update_hw_vlan_features() will always first put the
interface down, then update features and then bring it up again. But it
is possible to hit this code while the adapter is down and this causes a
non-paired call to napi_disable(), which will get stuck.

This patch fixes it by skipping these down/up actions if the interface
is already down.

Fixes: a45adbe8d3 ("qlge: Enhance nested VLAN (Q-in-Q) handling.")
Cc: Harish Patil <harish.patil@qlogic.com>
Signed-off-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-02-02 17:51:14 -08:00
David Ahern
9766e97af1 net: rocker: Add support for retrieving port level statistics
Add support for retrieving port level statistics from device.
Hook is added for ethtool's stats functionality. For example,

$ ethtool -S eth3
NIC statistics:
     rx_packets: 12
     rx_bytes: 2790
     rx_dropped: 0
     rx_errors: 0
     tx_packets: 8
     tx_bytes: 728
     tx_dropped: 0
     tx_errors: 0

Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-02-01 23:17:39 -08:00
Roopa Prabhu
eb0ac4207f rocker: set feature NETIF_F_HW_SWITCH_OFFLOAD
This patch sets the NETIF_F_HW_SWITCH_OFFLOAD feature flag on rocker ports

Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-02-01 23:16:34 -08:00
Roopa Prabhu
add511b382 bridge: add flags argument to ndo_bridge_setlink and ndo_bridge_dellink
bridge flags are needed inside ndo_bridge_setlink/dellink handlers to
avoid another call to parse IFLA_AF_SPEC inside these handlers

This is used later in this series

Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-02-01 23:16:33 -08:00
Sonic Zhang
b2dec116fb stmmac: DMA threshold mode or SF mode can be different among multiple device instance
- In tx_hard_error_bump_tc interrupt, tc should be bumped only when current
device instance is in DMA threshold mode. Check per device xstats.threshold
other than global tc.

- Set per device xstats.threshold to SF_DMA_MODE when current device
instance is set to SF mode.

v2-changes:
- fix ident style

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-02-01 23:14:24 -08:00
Hariprasad Shenai
3051fa617a cxgb4: Remove preprocessor check for CONFIG_CXGB4_DCB
In commit dc9daab226 ("cxgb4: Added support in debugfs to dump
sge_qinfo") a preprocessor check for CONFIG_CXGB4_DCB got added, which should
have been CONFIG_CHELSIO_T4_DCB. After adding the right preprocessor, build
fails due to missing function ethqset2pinfo. Fixing that as well.

V2: Updated description since the patch also fixes build failure

Reported-by: Paul Bolle <pebolle@tiscal.nl>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-02-01 22:38:00 -08:00
Karicheri, Muralidharan
58c11b5fae drivers: net: cpsw: make cpsw_ale.c a module to allow re-use on Keystone
NetCP on Keystone has cpsw ale function similar to other TI SoCs
and this driver is re-used. To allow both ti cpsw and keystone netcp
to re-use the driver, convert the cpsw ale to a module and configure
it through Kconfig option CONFIG_TI_CPSW_ALE. Currently it is statically
linked to both TI CPSW and NetCP and this causes issues when the above
drivers are built as dynamic modules. This patch addresses this issue

While at it, fix the Makefile and code to build both netcp_core and
netcp_ethss as dynamic modules. This is needed to support arm allmodconfig.
This also requires exporting of API calls provided by netcp_core so that
both the above can be dynamic modules.

Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-31 17:33:07 -08:00
Iyappan Subramanian
ecf6ba83d7 drivers: net: xgene: fix: Out of order descriptor bytes read
This patch fixes the following kernel crash,

	WARNING: CPU: 2 PID: 0 at net/ipv4/tcp_input.c:3079 tcp_clean_rtx_queue+0x658/0x80c()
	Call trace:
	[<fffffe0000096b7c>] dump_backtrace+0x0/0x184
	[<fffffe0000096d10>] show_stack+0x10/0x1c
	[<fffffe0000685ea0>] dump_stack+0x74/0x98
	[<fffffe00000b44e0>] warn_slowpath_common+0x88/0xb0
	[<fffffe00000b461c>] warn_slowpath_null+0x14/0x20
	[<fffffe00005b5c1c>] tcp_clean_rtx_queue+0x654/0x80c
	[<fffffe00005b6228>] tcp_ack+0x454/0x688
	[<fffffe00005b6ca8>] tcp_rcv_established+0x4a4/0x62c
	[<fffffe00005bf4b4>] tcp_v4_do_rcv+0x16c/0x350
	[<fffffe00005c225c>] tcp_v4_rcv+0x8e8/0x904
	[<fffffe000059d470>] ip_local_deliver_finish+0x100/0x26c
	[<fffffe000059dad8>] ip_local_deliver+0xac/0xc4
	[<fffffe000059d6c4>] ip_rcv_finish+0xe8/0x328
	[<fffffe000059dd3c>] ip_rcv+0x24c/0x38c
	[<fffffe0000563950>] __netif_receive_skb_core+0x29c/0x7c8
	[<fffffe0000563ea4>] __netif_receive_skb+0x28/0x7c
	[<fffffe0000563f54>] netif_receive_skb_internal+0x5c/0xe0
	[<fffffe0000564810>] napi_gro_receive+0xb4/0x110
	[<fffffe0000482a2c>] xgene_enet_process_ring+0x144/0x338
	[<fffffe0000482d18>] xgene_enet_napi+0x1c/0x50
	[<fffffe0000565454>] net_rx_action+0x154/0x228
	[<fffffe00000b804c>] __do_softirq+0x110/0x28c
	[<fffffe00000b8424>] irq_exit+0x8c/0xc0
	[<fffffe0000093898>] handle_IRQ+0x44/0xa8
	[<fffffe000009032c>] gic_handle_irq+0x38/0x7c
	[...]

Software writes poison data into the descriptor bytes[15:8] and upon
receiving the interrupt, if those bytes are overwritten by the hardware with
the valid data, software also reads bytes[7:0] and executes receive/tx
completion logic.

If the CPU executes the above two reads in out of order fashion, then the
bytes[7:0] will have older data and causing the kernel panic.  We have to
force the order of the reads and thus this patch introduces read memory
barrier between these reads.

Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Keyur Chudgar <kchudgar@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-30 18:17:31 -08:00
Toshiaki Makita
10e4fb333c ixgbevf: Fix checksum error when using stacked vlan
When a skb has multiple vlans and it is CHECKSUM_PARTIAL,
ixgbevf_tx_csum() fails to get the network protocol and checksum related
descriptor fields are not configured correctly because skb->protocol
doesn't show the L3 protocol in this case.

Use first->protocol instead of skb->protocol to get the proper network
protocol.

Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-30 18:03:47 -08:00
Toshiaki Makita
0213668f06 ixgbe: Fix checksum error when using stacked vlan
When a skb has multiple vlans and it is CHECKSUM_PARTIAL,
ixgbe_tx_csum() fails to get the network protocol and checksum related
descriptor fields are not configured correctly because skb->protocol
doesn't show the L3 protocol in this case.

Use vlan_get_protocol() to get the proper network protocol.

Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-30 18:03:47 -08:00
Toshiaki Makita
72b1405964 igbvf: Fix checksum error when using stacked vlan
When a skb has multiple vlans and it is CHECKSUM_PARTIAL,
igbvf_tx_csum() fails to get the network protocol and checksum related
descriptor fields are not configured correctly because skb->protocol
doesn't show the L3 protocol in this case.

Use vlan_get_protocol() to get the proper network protocol.

Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-30 18:03:47 -08:00
Tony Lindgren
f276c0ce5d net: davinci_emac: Get device MAC on 3517
Looks like on 3517 davinci_emac MAC address registers have a
different layout compared to dm816x and am33xx.

Let's add a function to get the 3517 MAC address.

Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-30 17:42:01 -08:00
Tony Lindgren
9120bd6e9f net: davinci_emac: Get device dm816x MAC address using the cpsw code
At least on dm81xx, we can get the davinci_emac MAC address the same
way as on am33xx cpsw.

Let's also use ether_addr_copy() for davinci_emac while at it.

Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-30 17:42:01 -08:00
Tony Lindgren
e5a49c1e3b net: cpsw: Add a minimal cpsw-common module for shared code
Looks like davinci_emac and cpsw can share some code although the
device registers have a different layout.

At least the code for getting the MAC address using syscon can
be shared by passing the register offset. Let's start with that
and set up a minimal shared cpsw-shared.c.

Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-30 17:42:01 -08:00
Arnd Bergmann
96a30175f9 net: am2150: fix nmclan_cs.c shared interrupt handling
A recent patch tried to work around a valid warning for the use of a
deprecated interface by blindly changing from the old
pcmcia_request_exclusive_irq() interface to pcmcia_request_irq().

This driver has an interrupt handler that is not currently aware
of shared interrupts, but can be easily converted to be.
At the moment, the driver reads the interrupt status register
repeatedly until it contains only zeroes in the interesting bits,
and handles each bit individually.

This patch adds the missing part of returning IRQ_NONE in case none
of the bits are set to start with, so we can move on to the next
interrupt source.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 5f5316fcd0 ("am2150: Update nmclan_cs.c to use update PCMCIA API")
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-29 15:08:21 -08:00
Arnd Bergmann
e9b106b8fb net: lance,ni64: don't build for ARM
The ni65 and lance ethernet drivers manually program the ISA DMA
controller that is only available on x86 PCs and a few compatible
systems. Trying to build it on ARM results in this error:

ni65.c: In function 'ni65_probe1':
ni65.c:496:62: error: 'DMA1_STAT_REG' undeclared (first use in this function)
     ((inb(DMA1_STAT_REG) >> 4) & 0x0f)
                                                              ^
ni65.c:496:62: note: each undeclared identifier is reported only once for each function it appears in
ni65.c:497:63: error: 'DMA2_STAT_REG' undeclared (first use in this function)
     | (inb(DMA2_STAT_REG) & 0xf0);

The DMA1_STAT_REG and DMA2_STAT_REG registers are only defined for
alpha, mips, parisc, powerpc and x86, although it is not clear
which subarchitectures actually have them at the correct location.

This patch for now just disables it for ARM, to avoid randconfig
build errors. We could also decide to limit it to the set of
architectures on which it does compile, but that might look more
deliberate than guessing based on where the drivers build.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-29 15:08:21 -08:00
Arnd Bergmann
fc9a570783 net: cs89x0: always build platform code if !HAS_IOPORT_MAP
The cs89x0 driver can either be built as an ISA driver or a platform
driver, the choice is controlled by the CS89x0_PLATFORM Kconfig
symbol. Building the ISA driver on a system that does not have
a way to map I/O ports fails with this error:

drivers/built-in.o: In function `cs89x0_ioport_probe.constprop.1':
:(.init.text+0x4794): undefined reference to `ioport_map'
:(.init.text+0x4830): undefined reference to `ioport_unmap'

This changes the Kconfig logic to take that option away and
always force building the platform variant of this driver if
CONFIG_HAS_IOPORT_MAP is not set. This is the only correct
choice in this case, and it avoids the build error.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-29 15:08:20 -08:00
Kevin Hao
4b222ca68a net: gianfar: remove the unneeded check of disabled device
Since commit cd1e65044d ("of/device: Don't register disabled
devices"), the disabled device will not be registered at all. So we
don't need to do the check again in the platform device driver.

Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-29 14:51:11 -08:00
Dan Carpenter
a154e6f6ef hisilicon: add some missing curly braces
The if block was supposed to have curly braces.  In the current code we
complain about dropped rx packets when we shouldn't.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-28 23:06:24 -08:00
Kweh, Hock Leong
d2a029bde3 stmmac: pci: add MSI support for Intel Quark X1000
In Intel Quark SoC X1000, both of the Ethernet controllers support
MSI interrupt handling. This patch enables them to use MSI interrupt
servicing in stmmac_pci for Intel Quark X1000.

Signed-off-by: Kweh, Hock Leong <hock.leong.kweh@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-27 21:08:08 -08:00
Andy Shevchenko
0763d955b4 stmmac: pci: introduce Intel Quark X1000 runtime detection
This patch introduces run-time board detection through DMI and MAC-PHY
configuration function used by quark_default_data() during initialization. It
fills up the phy_addr for Galileo and Galileo Gen2 boards to indicate that the
Ethernet MAC controller is or is not connected to any PHY.

The implementation takes into consideration for future expansion in Quark
series boards that may have different PHY address that is linked to its MAC
controllers.

This piece of work is derived from Bryan O'Donoghue's initial work for Quark
X1000 enabling.

Signed-off-by: Kweh, Hock Leong <hock.leong.kweh@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-27 21:08:08 -08:00
Kweh, Hock Leong
5b99a6b6cc stmmac: pci: add support for Intel Quark X1000
The Intel Quark SoC X1000 provides two 10/100 Mbps Ethernet MAC
controllers which may or may not be connected to PHY on board.
This MAC controller only supports RMII PHY. This patch add Quark
PCI ID as well as Quark default platform data info to this driver.

Signed-off-by: Kweh, Hock Leong <hock.leong.kweh@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-27 21:08:08 -08:00
Karicheri, Muralidharan
488327c6ef net: netcp: remove unused kconfig option and code
Currently CPTS is built into the netcp driver even though there is no
call out to the CPTS driver. This patch removes the dependency in Kconfig
and remove cpts.o from the Makefile for NetCP.

Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-27 17:19:18 -08:00
Hariprasad Shenai
cd6c2f12ec cxgb4: Move firmware version MACRO to t4fw_version.h
Move firmware version MACRO to a new t4fw_version.h file so that csiostor driver
can also use it.

Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-27 17:18:24 -08:00
Majd Dibbiny
6d6e996c20 net/mlx4_core: Update the HCA core clock frequency after INIT_PORT
The firmware might change the hca core clock frequency after the driver
issues the INIT_PORT command. Therefore we need to query the new
value again and save in to the cached dev caps.

Fixes: ddd8a6c1 ('net/mlx4_core: Read HCA frequency and map internal clock')
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-27 17:12:58 -08:00
Or Gerlitz
cb2147a925 net/mlx4_core: Fix device capabilities dumping
We are dumping device capabilities which are supported both by the
firmware and the driver. Align the array that holds the capability
strings with this practice.

Reported-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-27 17:12:58 -08:00
Matan Barak
19ab574f62 net/mlx4: Fix memory corruption in mlx4_MAD_IFC_wrapper
Fix a memory corruption at mlx4_MAD_IFC_wrapper.

A table of size dev->caps.pkey_table_len[port]*sizeof(*table)
was allocated, but get_full_pkey_table() assumes that the number
of entries in the table is a multiplication of 32 (which isn't always
correct).

Fixes: 0a9a018 ('mlx4: MAD_IFC paravirtualization')
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-27 17:12:58 -08:00
Saeed Mahameed
5a228c03d8 net/mlx4_en: Use ethtool cmd->autoneg as a hint for ethtool set settings
Use cmd->autoneg as a user hint to decide what to set in ethtool set settings callback.
When cmd->autoneg == AUTONEG_ENABLE set according to ethtool->advertise otherwise,
set according to ethtool->speed.

Usage:
	- ethtool -s eth<x> speed 56000 autoneg off
	- ethtool -s eth<x> advertise 0x800000 autoneg on

While we're here:
	- Move proto_admin masking outcome check to be adjacent to the operation.
	- Move en_warn("port reset..") print to "port reset" block.

Fixes: 312df74 ("net/mlx4_en: mlx4_en_set_settings() always fails when autoneg is set")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-27 17:12:58 -08:00
Jack Morgenstein
ef0223e693 net/mlx4_core: Remove duplicate code line from procedure mlx4_bf_alloc
mlx4_bf_alloc had an unnecessary/duplicate code line. Did no harm,
but not good practice.

Reported by the Mellanox Beijing team.

Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-27 17:12:57 -08:00
Jack Morgenstein
dc7d500451 net/mlx4_core: Fix struct mlx4_vhcr_cmd to make implicit padding explicit
Struct mlx4_vhcr was implicitly padded by the gcc compiler on 64-bit
architectures.

This commit makes that padding explicit, to prevent issues with
changing compilers and with incompatibilities between 32-bit architecture
implicit padding and 64-bit architecture implicit padding.

This structure is used in virtualization for communication between
the Host and its Guests. The explicit padding allows 64-bit Hosts
(old and new) to continue to interoperate with 64-bit Guests (old and new).

However, without this fix, 64-bit Hosts could not interoperate with 32-bit
Guests (since these did not insert the padding dword). With this fix,
32-bit Guests will be able to interoperate with 64-bit Hosts (since
the structure offsets will be identical on both).

Reported-by: Alexander Schmidt <alexs@linux.vnet.ibm.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-27 17:12:57 -08:00
Jack Morgenstein
30a5da5b33 net/mlx4_core: Fix HW2SW_EQ to conform to the firmware spec
The driver incorrectly assigned an out-mailbox to this command,
and used an opcode modifier = 0, which is a reserved value (it
should use opcode modifier = 1).

Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-27 17:12:57 -08:00
Jack Morgenstein
5a03108689 net/mlx4_core: Adjust command timeouts to conform to the firmware spec
The firmware spec states that the timeout for all commands should be 60 seconds.

In the past, the spec indicated that there were several classes of timeout
(short, medium, and long).  The driver has these different timeout classes.
We leave the class differentiation in the driver as-is (to protect against any
future spec changes), but set the timeout for all classes to be 60 seconds.

In addition, we fix a few commands which had hard-coded numeric timeouts specified.

Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-27 17:12:57 -08:00
Jack Morgenstein
772103e6b1 net/mlx4_core: Fix mem leak in SRIOV mlx4_init_one error flow
Structs allocated for the resource tracker must be freed in
the error flow.

Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-27 17:12:57 -08:00
Jack Morgenstein
f0ce061508 net/mlx4_core: Add reserved lkey for VFs to QUERY_FUNC_CAP
The reserved lKey is different for each VF.
A base lkey value is returned in QUERY_DEV_CAP at offset 0x98.

The reserved L_key value for a VF is:
    VF_lkey = base_lkey + (VF_number << 8).

This VF L_key value should be returned in QUERY_FUNC_CAP
(opcode-modifier = 0) at offset 0x48.

To indicate that the lkey value at offset 0x48 is valid, the Hypervisor
sets a flag bit in dword 0x0, offset 27 in the QUERY_FUNC_CAP wrapper
function.

When the VF calls QUERY_FUNC_CAP, it should check if this flag bit is set.
If it is set, the VF should take the reserved lkey value at offset 0x48.
If the bit is not set, the VF should not use a reserved lkey
(i.e., should set its reserved lkey value to 0).

Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-27 17:12:57 -08:00
Jack Morgenstein
be6a6b43b5 net/mlx4_core: Add bad-cable event support
If the firmware can detect a bad cable, allow it to generate an
event, and print the problem in the log.

Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-27 17:12:57 -08:00
David S. Miller
95f873f2ff Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Conflicts:
	arch/arm/boot/dts/imx6sx-sdb.dts
	net/sched/cls_bpf.c

Two simple sets of overlapping changes.

Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-27 16:59:56 -08:00
Andy Shevchenko
9afec6efc6 stmmac: prevent probe drivers to crash kernel
In the case when alloc_netdev fails we return NULL to a caller. But there is no
check for NULL in the probe drivers. This patch changes NULL to an error
pointer. The function description is amended to reflect what we may get
returned.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-27 12:24:30 -08:00
Rafał Miłecki
f65d539c6f r8169: use PCI define for Max_Read_Request_Size
Replace a magic number with a PCI #define symbol.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: David S. Miller <davem@davemloft.net>
2015-01-27 08:14:26 -06:00
Govindarajulu Varadarajan
24e579c889 bnx2x: fix napi poll return value for repoll
With the commit d75b1ade56 ("net: less interrupt masking in NAPI") napi
repoll is done only when work_done == budget. When in busy_poll is we return 0
in napi_poll. We should return budget.

Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-27 00:29:29 -08:00
David L Stevens
8e2b60cd18 sunvnet: improve error handling when a remote crashes
If a remote machine crashes while there are pending transmit buffers, the
sunvnet driver reallocates the ring descriptors giving us enries that have
state VIO_DESC_FREE but also an allocated skb. This results in a BUG_ON()
call when the remote reboots and we reach that point in the ring.

This patch:

1) clears pending tx packets in the ring on port reset
2) changes a BUG_ON() to a pr_warn() when a remote host has given us an invalid
	descriptor state
3) collapses multiple active buffer frees in a ring to a single message per
	ring and adds the device name and remote MAC address

This fixes the particular problem of not cleaning up pending buffers on a
reset, but also prevents us from crashing if the remote handles descriptors
out of order or sets an unexpected state for a descriptor.

Signed-off-by: David L Stevens <david.stevens@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-27 00:25:21 -08:00
David L Stevens
07ac3e7099 sunvnet: free pending tx buffers before clearing ring data
This patch moves the clearing of ring data in vnet_port_free_tx_bufs to after
 the freeing of pending buffers in the ring. Otherwise, this can result in
 dereferencing a NULL pointer.

Reported-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David L Stevens <david.stevens@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-27 00:25:21 -08:00
Ben Hutchings
52b9fa3696 sh_eth: Fix DMA-API usage for RX buffers
- Use the return value of dma_map_single(), rather than calling
  virt_to_page() separately
- Check for mapping failue
- Call dma_unmap_single() rather than dma_sync_single_for_cpu()

Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-27 00:18:54 -08:00
Ben Hutchings
aa3933b873 sh_eth: Check for DMA mapping errors on transmit
dma_map_single() may fail if an IOMMU or swiotlb is in use, so
we need to check for this.

Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-27 00:18:53 -08:00
Ben Hutchings
740c7f31c0 sh_eth: Ensure DMA engines are stopped before freeing buffers
Currently we try to clear EDRRR and EDTRR and immediately continue to
free buffers.  This is unsafe because:

- In general, register writes are not serialised with DMA, so we still
  have to wait for DMA to complete somehow
- The R8A7790 (R-Car H2) manual states that the TX running flag cannot
  be cleared by writing to EDTRR
- The same manual states that clearing the RX running flag only stops
  RX DMA at the next packet boundary

I applied this patch to the driver to detect DMA writes to freed
buffers:

> --- a/drivers/net/ethernet/renesas/sh_eth.c
> +++ b/drivers/net/ethernet/renesas/sh_eth.c
> @@ -1098,7 +1098,14 @@ static void sh_eth_ring_free(struct net_device *ndev)
>  	/* Free Rx skb ringbuffer */
>  	if (mdp->rx_skbuff) {
>  		for (i = 0; i < mdp->num_rx_ring; i++)
> +			memcpy(mdp->rx_skbuff[i]->data,
> +			       "Hello, world", 12);
> +		msleep(100);
> +		for (i = 0; i < mdp->num_rx_ring; i++) {
> +			WARN_ON(memcmp(mdp->rx_skbuff[i]->data,
> +				       "Hello, world", 12));
>  			dev_kfree_skb(mdp->rx_skbuff[i]);
> +		}
>  	}
>  	kfree(mdp->rx_skbuff);
>  	mdp->rx_skbuff = NULL;

then ran the loop:

    while ethtool -G eth0 rx 128 ; ethtool -G eth0 rx 64; do echo -n .; done

and 'ping -f' toward the sh_eth port from another machine.  The
warning fired several times a minute.

To fix these issues:

- Deactivate all TX descriptors rather than writing to EDTRR
- As there seems to be no way of telling when RX DMA is stopped,
  perform a soft reset to ensure that both DMA enginess are stopped
- To reduce the possibility of the reset truncating a transmitted
  frame, disable egress and wait a reasonable time to reach a
  packet boundary before resetting
- Update statistics before resetting

(The 'reasonable time' does not allow for CS/CD in half-duplex
mode, but half-duplex no longer seems reasonable!)

Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-27 00:18:53 -08:00
Ben Hutchings
dc1d0e6d55 sh_eth: Remove RX overflow log messages
If RX traffic is overflowing the FIFO or DMA ring, logging every time
this happens just makes things worse.  These errors are visible in the
statistics anyway.

Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-27 00:18:53 -08:00
Hariprasad Shenai
b58b667687 cxgb4: Added support in debugfs to dump different timer and clock values of the adapter
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-27 00:15:02 -08:00
Hariprasad Shenai
b3bbe36a26 cxgb4: Added support in debugfs to dump PM module stats
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-27 00:15:02 -08:00
Hariprasad Shenai
c778af7d18 cxgb4: Addded support in debugfs to dump CIM outbound queue content
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-27 00:15:01 -08:00
Hariprasad Shenai
e5f0e43bee cxgb4: Added support in debugfs to dump cim ingress bound queue contents
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-27 00:15:01 -08:00
Hariprasad Shenai
dc9daab226 cxgb4: Added support in debugfs to dump sge_qinfo
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-27 00:15:01 -08:00
Michal Simek
d23823dd61 net: macb: Remove CONFIG_PM ifdef because of compilation warning
Fix compilation warning:
drivers/net/ethernet/cadence/macb.c:2415:12: warning: 'macb_suspend'
defined but not used [-Wunused-function]
 static int macb_suspend(struct device *dev)
drivers/net/ethernet/cadence/macb.c:2432:12: warning: 'macb_resume'
defined but not used [-Wunused-function]
 static int macb_resume(struct device *dev)

when CONFIG_PM=y, CONFIG_PM_SLEEP=n are used.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-26 17:26:03 -08:00
Nicolae Rosia
9e86d7667c net: macb: allow deffered probe of the driver
The driver is trying to acquire clocks which maybe
are not available yet. Allow the driver to request
deffered probe by providing a probe function and
registering it with module_platform_driver. [1]
This patch is based on 3.19-rc5.

[1] https://lkml.org/lkml/2013/9/23/118

Signed-off-by: Nicolae Rosia <nicolae.rosia@certsign.ro>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-26 17:08:33 -08:00
Ezequiel Garcia
9e911414af net: mv643xx_eth: Fix highmem support in non-TSO egress path
Commit 69ad0dd7af
Author: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Date:   Mon May 19 13:59:59 2014 -0300

    net: mv643xx_eth: Use dma_map_single() to map the skb fragments

caused a nasty regression by removing the support for highmem skb
fragments. By using page_address() to get the address of a fragment's
page, we are assuming a lowmem page. However, such assumption is incorrect,
as fragments can be in highmem pages, resulting in very nasty issues.

This commit fixes this by using the skb_frag_dma_map() helper,
which takes care of mapping the skb fragment properly. Additionally,
the type of mapping is now tracked, so it can be unmapped using
dma_unmap_page or dma_unmap_single when appropriate.

This commit also fixes the error path in txq_init() to release the
resources properly.

Fixes: 69ad0dd7af ("net: mv643xx_eth: Use dma_map_single() to map the skb fragments")
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-26 16:14:40 -08:00
Ben Hutchings
283e38db65 sh_eth: Fix serialisation of interrupt disable with interrupt & NAPI handlers
In order to stop the RX path accessing the RX ring while it's being
stopped or resized, we clear the interrupt mask (EESIPR) and then call
free_irq() or synchronise_irq().  This is insufficient because the
interrupt handler or NAPI poller may set EESIPR again after we clear
it.  Also, in sh_eth_set_ringparam() we currently don't disable NAPI
polling at all.

I could easily trigger a crash by running the loop:

   while ethtool -G eth0 rx 128 && ethtool -G eth0 rx 64; do echo -n .; done

and 'ping -f' toward the sh_eth port from another machine.

To fix this:
- Add a software flag (irq_enabled) to signal whether interrupts
  should be enabled
- In the interrupt handler, if the flag is clear then clear EESIPR
  and return
- In the NAPI poller, if the flag is clear then don't set EESIPR
- Set the flag before enabling interrupts in sh_eth_dev_init() and
  sh_eth_set_ringparam()
- Clear the flag and serialise with the interrupt and NAPI
  handlers before clearing EESIPR in sh_eth_close() and
  sh_eth_set_ringparam()

After this, I could run the loop for 100,000 iterations successfully.

Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-26 16:13:15 -08:00
Ben Hutchings
084236d8c5 sh_eth: Fix crash or memory leak when resizing rings on device that is down
If the device is down then no packet buffers should be allocated.
We also must not touch its registers as it may be powered off.

Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-26 16:13:15 -08:00
Ben Hutchings
bd8889163a sh_eth: Detach net device when stopping queue to resize DMA rings
We must only ever stop TX queues when they are full or the net device
is not 'ready' so far as the net core, and specifically the watchdog,
is concerned.  Otherwise, the watchdog may fire *immediately* if no
packets have been added to the queue in the last 5 seconds.

What's more, sh_eth_tx_timeout() will likely crash if called while
we're resizing the TX ring.

I could easily trigger this by running the loop:

   while ethtool -G eth0 rx 128 && ethtool -G eth0 rx 64; do echo -n .; done

Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-26 16:13:15 -08:00
Ben Hutchings
eebfb643c0 sh_eth: Fix padding of short frames on TX
If an skb to be transmitted is shorter than the minimum Ethernet frame
length, we currently set the DMA descriptor length to the minimum but
do not add zero-padding.  This could result in leaking sensitive
data.  We also pass different lengths to dma_map_single() and
dma_unmap_single().

Use skb_padto() to pad properly, before calling dma_map_single().

Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-26 16:13:15 -08:00
Mugunthan V N
02a54164c5 drivers: net: cpsw: discard dual emac default vlan configuration
In Dual EMAC, the default VLANs are used to segregate Rx packets between
the ports, so adding the same default VLAN to the switch will affect the
normal packet transfers. So returning error on addition of dual EMAC
default VLANs.

Even if EMAC 0 default port VLAN is added to EMAC 1, it will lead to
break dual EMAC port separations.

Fixes: d9ba8f9e62 (driver: net: ethernet: cpsw: dual emac interface implementation)
Cc: <stable@vger.kernel.org> # v3.9+
Reported-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-26 16:05:50 -08:00
Sonic Zhang
fa067467d8 stmmac: Add an optional device tree property "snps,burst_len"
This property define the AXI bug lenth.

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-26 15:48:01 -08:00
Sonic Zhang
dec2165ff3 stmmac: hardware TX COE doesn't work when force_thresh_dma_mode is set
Clear the TX COE bit when force_thresh_dma_mode is set even hardware
dma capability says support.

Tested on BF609.

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-26 15:48:01 -08:00
Sonic Zhang
c405abe2e0 stmmac: if force_thresh_dma_mode is set, pass tc to both txmode and rxmode in tx_hard_error_bump_tc interrupt
Dont' pass SF_DMA_MODE to rxmode in this case.

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-26 15:48:01 -08:00
Mikhail Ulyanov
b71af04676 sh_eth: add more PM methods
Add sh_eth_{suspend|resume}() implementing {suspend|resume|freeze|thaw|poweroff|
restore}() PM methods to make it possible to restore from hibernation not only
in Linux  but also in e.g. U-Boot and  to have more determined state on resume/
restore.

Signed-off-by: Mikhail Ulyanov <mikhail.ulyanov@cogentembedded.com>
[Sergei: moved sh_eth_{suspend|resume}() before sh_eth_runtime_nop(), enclosed
them with #ifdef CONFIG_PM_SLEEP, reordered the local variables, got rid of
*goto* and label, reordered macro invocations, renamed, modified the changelog.]
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-26 15:26:41 -08:00
Mikhail Ulyanov
e7d7e89846 sh_eth: use SET_RUNTIME_PM_OPS()
Use SET_RUNTIME_PM_OPS() macro to initialize the runtime PM method pointers in
the 'struct dev_pm_ops'.

Signed-off-by: Mikhail Ulyanov <mikhail.ulyanov@cogentembedded.com>
[Sergei: renamed, added the changelog.]
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-26 15:26:41 -08:00
Beniamino Galvani
3897957494 net: stmmac: add BQL support
Add support for Byte Queue Limits to the STMicro MAC driver.

Tested on a Amlogic S802 quad Cortex-A9 board, where the use of BQL
decreases the latency of a high priority ping from ~12ms to ~1ms when
the 100Mbit link is saturated by 20 TCP streams.

Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-26 15:22:15 -08:00
Hariprasad Shenai
1793c798c3 cxgb4: Fixes cxgb4_inet6addr_notifier unregister call
commit b5a02f503c ("cxgb4 : Update ipv6 address handling api") introduced
a regression where unregister cxgb4_inet6addr_notifier wasn't getting called
during module_exit.

Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-26 14:45:46 -08:00
Shaohui Xie
22f6bba77f net/fsl: Replace spin_event_timeout() with arch independent in xgmac_mdio
spin_event_timeout() is PPC dependent, use an arch independent
equivalent instead.

Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-25 23:36:06 -08:00
Shaohui Xie
ca43e58ca2 net/fsl: drop in_be32() & out_be32() in xgmac_mdio
Use ioread32be() & iowrite32be() instead.

Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-25 23:36:05 -08:00
Al Viro
92fc41c3a6 mode_t whack-a-mole: chelsio
it's umode_t, damnit...

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
2015-01-25 23:16:28 -05:00
Yishai Hadas
0cd9302734 net/mlx4_core: Reset flow activation upon SRIOV fatal command cases
When SRIOV commands are executed over the comm-channel and get
a fatal error (e.g. timeout, closing command failure) the VF enters
into error state and reset flow is activated.

To be able to recognize whether the failure was on a closing command, the
operational code for the given VHCR command is used. Once the device entered
into an error state we prevent redundant error messages from being printed.

Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-25 14:43:15 -08:00
Yishai Hadas
55ad359225 net/mlx4_core: Enable device recovery flow with SRIOV
In SRIOV, both the PF and the VF may attempt device recovery whenever they
assume that the device is not functioning.  When the PF driver resets the
device, the VF should detect this and attempt to reinitialize itself.

The VF must be able to reset itself under all circumstances, even
if the PF is not responsive.

The VF shall reset itself in the following cases:

1. Commands are not processed within reasonable time over the communication channel.
This is done considering device state and the correct return code based on
the command as was done in the native mode, done in the next patch.

2. The VF driver receives an internal error event reported by the PF on the
communication channel. This occurs when the PF driver resets the device or
when VF is out of sync with the PF.

Add 'VF reset' capability, which allows the VF to reinitialize itself even when the
PF is not responsive.

As PF and VF may run their reset flow simulantanisly, there are several cases
that are handled:
- Prevent freeing VF resources upon FLR, when PF is in its unloading stage.
- Prevent PF getting VF commands before it has finished initializing its resources.
- Upon VF startup, check that comm-channel is online before sending
  commands to the PF and getting timed-out.

Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-25 14:43:14 -08:00
Yishai Hadas
2ba5fbd62b net/mlx4_core: Handle AER flow properly
Fix AER callbacks to work properly, it includes:
- Refractoring AER to be aligned with Reset flow support.
- Sync with concurrent catas flow.

In addition, fix the shutdown PCI callback to sync with
concurrent catas flow.

Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-25 14:43:14 -08:00
Yishai Hadas
c69453e294 net/mlx4_core: Manage interface state for Reset flow cases
We need to manage interface state to sync between reset flow and some other
relative cases such as remove_one. This has to be done to prevent certain
races. For example in case software stack is down as a result of unload call,
the remove_one should skip the unload phase.

Implement the remove_one case, handling AER and other cases comes next.

The interface can be up/down, upon remove_one, the state will include an extra
bit indicating that the device is cleaned-up, forcing other tasks to finish
before the final cleanup.

Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-25 14:43:14 -08:00
Yishai Hadas
f5aef5aa35 net/mlx4_core: Activate reset flow upon fatal command cases
We activate reset flow upon command fatal errors, when the device enters an
erroneous state, and must be reset.

The cases below are assumed to be fatal: FW command timed-out, an error from FW
on closing commands, pci is offline when posting/pending a command.

In those cases we place the device into an error state: chip is reset, pending
commands are awakened and completed immediately. Subsequent commands will
return immediately.

The return code in the above cases will depend on the command. Commands which
free and close resources will return success (because the chip was reset, so
callers may safely free their kernel resources). Other commands will return -EIO.

Since the device's state was marked as error, the catas poller will
detect this and restart the device's software stack (as is done when a FW
internal error is directly detected). The device state is protected by a
persistent mutex lives on its mlx4_dev, as such no need any more for the
hcr_mutex which is removed.

Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-25 14:43:14 -08:00
Yishai Hadas
f6bc11e426 net/mlx4_core: Enhance the catas flow to support device reset
This includes:

- resetting the chip when a fatal error is detected (the current code
  does not do this).

- exposing the ability to enter error state from outside the catas code
  by calling its functionality. (E.g. FW Command timeout, AER error).

- managing a persistent device state. This is needed to sync between
  reset flow cases.

Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-25 14:43:14 -08:00
Yishai Hadas
ad9a0bf08f net/mlx4_core: Refactor the catas flow to work per device
Using a WQ per device instead of a single global WQ, this allows
independent reset handling per device even when SRIOV is used.

This comes as a pre-patch for supporting chip reset
for both native and SRIOV.

Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-25 14:43:14 -08:00
Yishai Hadas
dd0eefe3ab net/mlx4_core: Set device configuration data to be persistent across reset
When an HCA enters an internal error state, this is detected by the driver.
The driver then should reset the HCA and restart the software stack.

Keep ports information and some SRIOV configuration in a persistent area
to have it valid across reset.

Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-25 14:43:13 -08:00