The change setup the peripheral clock (PERIPH_CLK) as the default
parent clock for PWM1 & PWM2.
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
The change adds a new device node with description of generic SRAM
on-chip memory found on NXP LPC32xx SoC series and connected to AHB
matrix slave port 3.
Note that NXP LPC3220 SoC has 128KiB of SRAM memory, the other
LPC3230, LPC3240 and LPC3250 SoCs all have 256KiB SRAM space,
in the shared DTSI file this change specifies 128KiB SRAM size.
Also it's worth to mention that the SRAM area contains of 64KiB banks,
2 banks on LPC3220 and 4 banks on the other SoCs from the series, and
all SRAM banks but the first one have independent power controls,
the description of this feature will be added with the introduction of
power domains for the SoC series.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Sylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The change adds separate device nodes for SIC1 and SIC2 interrupt
controllers and reparents all defined SIC1 and SIC2 interrupt
producers to the correspondent interrupt controller, this is needed to
perform switching to a new LPC32xx MIC/SIC interrupt controller driver.
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
The SSP0/SPI1 and SSP1/SPI2 shared pinout and should be disable by
default.
Board specific dts should enable them, as needed.
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
The change adds clock properties to spi peripheral devices,
clock ids are taken from dt-bindings/clock/lpc32xx-clock.h
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Probably most of NXP LPC32xx boards have 13MHz main oscillator and
therefore for HCLK PLL and ARM core clock rate default hardware
setting is 16 * 13MHz = 208MHz, however a user may vary HCLK PLL/ARM
core rate from 156MHz to about 266MHz for 13MHz clock source.
The change explicitly defines HCLK PLL output rate to default 208MHz
to overwrite any settings done by a bootloader, if needed it can be
redefined in a board DTS file.
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
LPC32xx interrupt controller has two cells, instead of zero
specify proper irq types for all consumers.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
If clock-frequency property is given, then it substitutes calculation
of supplying clock frequency from parent clock, this may break UART,
if parent clock is given and managed by common clock framework.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
The change adds device node of LPC32xx USB clock controller and adds
clock properties to USB OHCI, USB device and I2C controller to USB phy
device nodes.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
The change adds clock properties to all described peripheral devices,
clock ids are taken from dt-bindings/clock/lpc32xx-clock.h
Some existing drivers expect to get clock names, in those cases
clock-names are added as well.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
NXP LPC32xx SoC has a clocking and power control unit (CPC) as a part
of system control block (SCB). CPC is supplied by two external
oscillators and it manages core and most of peripheral clocks, the
change adds SCB and CPC descriptions to shared LPC32xx dtsi file.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
NXP LPC32xx SoC has two external oscillators - one is mandatory and
always on 32768 Hz oscillator and one optional 10-20MHz oscillator,
which is practically always present on LPC32xx boards, because its
presence is needed to supply USB controller clock and by default it
supplies ARM and most of the peripheral clocks, LPC32xx User's Manual
references it as a main oscillator.
The change adds device nodes for both oscillators, frequency of
the main oscillator is selected to be 13MHz by default, this variant
is found on all LPC32xx reference boards.
The device nodes for external oscillators are needed to describe input
clocks of LPC32xx clock controller.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
NXP LPC32xx SoC has one USB OTG controller, which is supposed to work
with an external phy (default is NXP ISP1301).
Practically the USB controller contains 5 subdevices:
- host controller 0x3102 0000 -- 0x3102 00FF
- OTG controller 0x3102 0100 -- 0x3102 01FF
- device controller 0x3102 0200 -- 0x3102 02FF
- I2C controller 0x3102 0300 -- 0x3102 03FF
- clock controller 0x3102 0F00 -- 0x3102 0FFF
The USB controller can be considered as a "bus", because the
subdevices above are relatively independent, for example I2C
controller is the same as other two general purpose I2C controllers
found on SoC.
The change is not intended to modify any logic, but it rearranges
existing device nodes, in future it is planned to add a USB clock
controller device node into the same group.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
The change adds a description of ARM PrimeCell PL175 memory
controller, which is found on NXP LPC32xx SoCs.
The controller supports up to 4 static memory devices mapped to
0xE000 0000 - 0xE3FF FFFF physical memory area.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
LPC32xx SoCs have two independent PWM controllers, they have different
clock parents, clock gates and even slightly different controls,
each of these two PWM controllers has one output channel. Due to
almost similar controls arranged in a row it is incorrectly assumed
that there is one PWM controller with two channels, fix this problem
in lpc32xx.dtsi, which at the moment prevents separate configuration
of different clock parents and gates for both PWM controllers.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
According to device tree bindings for ARM cpus cpu node must contain a
reg property for enumeration scheme.
The change adds reg = <0x0> indicating that the processor does not
have CPU identification register and updates cell settings.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
To simplify writing of dts files for all lpc32xx.dtsi users who adjust
device node properties, add labels to all defined peripheral device
nodes in lpc32xx.dtsi.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
The change replaces /include/ to #include in lpc32xx.dtsi and
derivatives, it is required, if C preprocessor is intended to be used
over dtsi/dts files, otherwise errors like one below are generated:
Error: ea3250.dts:15.1-9 syntax error
FATAL ERROR: Unable to parse input tree
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
This patch updates the in-kernel dts files according to the latest cpus
and cpu bindings updates for ARM.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
This patches fixes some status = "disable" strings to "disabled", the correct
way of disabling nodes in the devicetree.
Signed-off-by: Roland Stigge <stigge@antcom.de>
This patch fixes the DTS files for the High Speed UARTs 1, 2 and 7 of the
LPC32xx SoC, adjusting the compatible strings, adding interrupts and status
configuration. On the PHY3250 reference board, UART2 is enabled.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
This patch switches from static serial driver initialization to devicetree
configuration. This way, the Standard UARTs of the LPC32xx SoC can be enabled
individually via DT.
E.g., instead of Kconfig configuration, the phy3250.dts activates
UARTs 3 and 5.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Tested-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
This patch connects the lpc32xx-key driver to the LPC32xx platform (via
lpc32xx.dtsi), and more specifically to the reference board via its dts file.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
This patch takes into account that the MTD NAND MLC controller needs more
registers, located actually before the previously allocated memory range,
already starting at 200a8000 instead of 200b0000.
Further, the interrupt for the controller is configured.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Tested-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
The GPIO devicetree binding in 3.5 doesn't register the various LPC32xx GPIO
banks via DT subnodes but always all at once, and changes the gpio referencing
to 3 cells (bank, gpio, flags). This patch adjusts the DTS files to this
binding that was just accepted to the gpio subsystem.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch adds the dts files for the reference machine of LPC32xx:
* arch/arm/boot/dts/lpc32xx.dtsi: Include for devices based on LPC32xx
* arch/arm/boot/dts/phy3250.dts: Board support for PHYTEC phyCORE-LPC3250
Signed-off-by: Roland Stigge <stigge@antcom.de>
