Initialize a few missing window context fields from the window attributes
specified by the caller. These fields are currently set to their default
values by the caller (NX-842), but would be good to apply them anyway.
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Take the DSCR value set by firmware as the dscr_default value,
rather than zero.
POWER9 recommends DSCR default to a non-zero value.
Signed-off-by: From: Nicholas Piggin <npiggin@gmail.com>
[mpe: Make record_spr_defaults() __init]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
OPAL boot does not insert secondaries at 0x60 to wait at the secondary
hold spinloop. Instead they are started later, and inserted at
generic_secondary_smp_init(), which is after the secondary hold
spinloop.
Avoid waiting on this spinloop when booting with OPAL firmware. This
wait always times out that case.
This saves 100ms boot time on powernv, and 10s of seconds of real time
when booting on the simulator in SMP.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Unmaps that free page tables always flush the entire PID, which is
sub-optimal. Provide TLB range flushing with an additional PWC flush
that can be use for va range invalidations with PWC flush.
Time to munmap N pages of memory including last level page table
teardown (after mmap, touch), local invalidate:
N 1 2 4 8 16 32 64
vanilla 3.2us 3.3us 3.4us 3.6us 4.1us 5.2us 7.2us
patched 1.4us 1.5us 1.7us 1.9us 2.6us 3.7us 6.2us
Global invalidate:
N 1 2 4 8 16 32 64
vanilla 2.2us 2.3us 2.4us 2.6us 3.2us 4.1us 6.2us
patched 2.1us 2.5us 3.4us 5.2us 8.7us 15.7us 6.2us
Local invalidates get much better across the board. Global ones have
the same issue where multiple tlbies for va flush do get slower than
the single tlbie to invalidate the PID. None of this test captures
the TLB benefits of avoiding killing everything.
Global gets worse, but it is brought in to line with global invalidate
for munmap()s that do not free page tables.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The single page flush ceiling is the cut-off point at which we switch
from invalidating individual pages, to invalidating the entire process
address space in response to a range flush.
Introduce a local variant of this heuristic because local and global
tlbie have significantly different properties:
- Local tlbiel requires 128 instructions to invalidate a PID, global
tlbie only 1 instruction.
- Global tlbie instructions are expensive broadcast operations.
The local ceiling has been made much higher, 2x the number of
instructions required to invalidate the entire PID (i.e., 256 pages).
Time to mprotect N pages of memory (after mmap, touch), local invalidate:
N 32 34 64 128 256 512
vanilla 7.4us 9.0us 14.6us 26.4us 50.2us 98.3us
patched 7.4us 7.8us 13.8us 26.4us 51.9us 98.3us
The behaviour of both is identical at N=32 and N=512. Between there,
the vanilla kernel does a PID invalidate and the patched kernel does
a va range invalidate.
At N=128, these require the same number of tlbiel instructions, so
the patched version can be sen to be cheaper when < 128, and more
expensive when > 128. However this does not well capture the cost
of invalidated TLB.
The additional cost at 256 pages does not seem prohibitive. It may
be the case that increasing the limit further would continue to be
beneficial to avoid invalidating all of the process's TLB entries.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently for radix, flush_tlb_range flushes the entire PID, because
the Linux mm code does not tell us about page size here for THP vs
regular pages. This is quite sub-optimal for small mremap / mprotect
/ change_protection.
So implement va range flushes with two flush passes, one for each
page size (regular and THP). The second flush has an order of matnitude
fewer tlbie instructions than the first, so it is a relatively small
additional cost.
There is still room for improvement here with some changes to generic
APIs, particularly if there are mostly THP pages to be invalidated,
the small page flushes could be reduced.
Time to mprotect 1 page of memory (after mmap, touch):
vanilla 2.9us 1.8us
patched 1.2us 1.6us
Time to mprotect 30 pages of memory (after mmap, touch):
vanilla 8.2us 7.2us
patched 6.9us 17.9us
Time to mprotect 34 pages of memory (after mmap, touch):
vanilla 9.1us 8.0us
patched 9.0us 8.0us
34 pages is the point at which the invalidation switches from va
to entire PID, which tlbie can do in a single instruction. This is
why in the case of 30 pages, the new code runs slower for this test.
This is a deliberate tradeoff already present in the unmap and THP
promotion code, the idea is that the benefit from avoiding flushing
entire TLB for this PID on all threads in the system.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Move the barriers and range iteration down into the _tlbie* level,
which improves readability.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Short range flushes issue a sequences of tlbie(l) instructions for
individual effective addresses. These do not all require individual
barrier sequences, only one covering all tlbie(l) instructions.
Commit f7327e0ba3 ("powerpc/mm/radix: Remove unnecessary ptesync")
made a similar optimization for tlbiel for PID flushing.
For tlbie, the ISA says:
The tlbsync instruction provides an ordering function for the
effects of all tlbie instructions executed by the thread executing
the tlbsync instruction, with respect to the memory barrier
created by a subsequent ptesync instruction executed by the same
thread.
Time to munmap 30 pages of memory (after mmap, touch):
local global
vanilla 10.9us 22.3us
patched 3.4us 14.4us
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We have some dependencies & conflicts between patches in fixes and
things to go in next, both in the radix TLB flush code and the IMC PMU
driver. So merge fixes into next.
Add a self test to check if FP/VEC/VSX registers are sane (restored
correctly) after a FP/VEC/VSX unavailable exception is caught during a
transaction.
This test checks all possibilities in a thread regarding the combination
of MSR.[FP|VEC] states in a thread and for each scenario raises a
FP/VEC/VSX unavailable exception in transactional state, verifying if
vs0 and vs32 registers, which are representatives of FP/VEC/VSX reg
sets, are not corrupted.
Signed-off-by: Gustavo Romero <gromero@linux.vnet.ibm.com>
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
It would be nice to be able to dump page tables in a particular
context.
eg: dumping vmalloc space:
0:mon> dv 0xd00037fffff00000
pgd @ 0xc0000000017c0000
pgdp @ 0xc0000000017c00d8 = 0x00000000f10b1000
pudp @ 0xc0000000f10b13f8 = 0x00000000f10d0000
pmdp @ 0xc0000000f10d1ff8 = 0x00000000f1102000
ptep @ 0xc0000000f1102780 = 0xc0000000f1ba018e
Maps physical address = 0x00000000f1ba0000
Flags = Accessed Dirty Read Write
This patch does not replicate the complex code of dump_pagetable and
has no support for bolted linear mapping, thats why I've it's called
dump virtual page table support. The format of the PTE can be expanded
even further to add more useful information about the flags in the PTE
if required.
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
[mpe: Bike shed the output format, show the pgdir, fix build failures]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In commit e6f81a9201 ("powerpc/mm/hash: Support 68 bit VA") the
masking is folded into ASM_VSID_SCRAMBLE but the comment about masking
is removed only from the firt use of ASM_VSID_SCRAMBLE.
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
DMA windows can only have a size of power of two on IODA2 hardware and
using memory_hotplug_max() to determine the upper limit won't work
correcly if it returns not power of two value.
This removes the check as the platform code does this check in
pnv_pci_ioda2_setup_default_config() anyway; the other client is VFIO
and that thing checks against locked_vm limit which prevents the userspace
from locking too much memory.
It is expected to impact DPDK on machines with non-power-of-two RAM size,
mostly. KVM guests are less likely to be affected as usually guests get
less than half of hosts RAM.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The call to /proc/cpuinfo in turn calls cpufreq_quick_get() which
returns the last frequency requested by the kernel, but may not
reflect the actual frequency the processor is running at. This patch
makes a call to cpufreq_get() instead which returns the current
frequency reported by the hardware.
Fixes: fb5153d05a ("powerpc: powernv: Implement ppc_md.get_proc_freq()")
Signed-off-by: Shriya <shriyak@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
DD2.1 does not have to save MMCR0 for all state-loss idle states,
only after deep idle states (like other PMU registers).
Reviewed-by: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
DD2.1 does not have to flush the ERAT after a state-loss idle.
Performance testing was done on a DD2.1 using only the stop0 idle state
(the shallowest state which supports state loss), using context_switch
selftest configured to ping-poing between two threads on the same core
and two different cores.
Performance improvement for same core is 7.0%, different cores is 14.8%.
Reviewed-by: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
After handling a transactional FP, Altivec or VSX unavailable exception.
The return to userspace code will detect that the TIF_RESTORE_TM bit is
set and call restore_tm_state(). restore_tm_state() will call
restore_math() to ensure that the correct facilities are loaded.
This means that all the loadup code in {fp,altivec,vsx}_unavailable_tm()
is doing pointless work and can simply be removed.
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Lazy save and restore of FP/Altivec means that a userspace process can
be sent to userspace with FP or Altivec disabled and loaded only as
required (by way of an FP/Altivec unavailable exception). Transactional
Memory complicates this situation as a transaction could be started
without FP/Altivec being loaded up. This causes the hardware to
checkpoint incorrect registers. Handling FP/Altivec unavailable
exceptions while a thread is transactional requires a reclaim and
recheckpoint to ensure the CPU has correct state for both sets of
registers.
tm_reclaim() has optimisations to not always save the FP/Altivec
registers to the checkpointed save area. This was originally done
because the caller might have information that the checkpointed
registers aren't valid due to lazy save and restore. We've also been a
little vague as to how tm_reclaim() leaves the FP/Altivec state since it
doesn't necessarily always save it to the thread struct. This has lead
to an (incorrect) assumption that it leaves the checkpointed state on
the CPU.
tm_recheckpoint() has similar optimisations in reverse. It may not
always reload the checkpointed FP/Altivec registers from the thread
struct before the trecheckpoint. It is therefore quite unclear where it
expects to get the state from. This didn't help with the assumption
made about tm_reclaim().
These optimisations sit in what is by definition a slow path. If a
process has to go through a reclaim/recheckpoint then its transaction
will be doomed on returning to userspace. This mean that the process
will be unable to complete its transaction and be forced to its failure
handler. This is already an out if line case for userspace. Furthermore,
the cost of copying 64 times 128 bits from registers isn't very long[0]
(at all) on modern processors. As such it appears these optimisations
have only served to increase code complexity and are unlikely to have
had a measurable performance impact.
Our transactional memory handling has been riddled with bugs. A cause
of this has been difficulty in following the code flow, code complexity
has not been our friend here. It makes sense to remove these
optimisations in favour of a (hopefully) more stable implementation.
This patch does mean that some times the assembly will needlessly save
'junk' registers which will subsequently get overwritten with the
correct value by the C code which calls the assembly function. This
small inefficiency is far outweighed by the reduction in complexity for
general TM code, context switching paths, and transactional facility
unavailable exception handler.
0: I tried to measure it once for other work and found that it was
hiding in the noise of everything else I was working with. I find it
exceedingly likely this will be the case here.
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Lazy save and restore of FP/Altivec means that a userspace process can
be sent to userspace with FP or Altivec disabled and loaded only as
required (by way of an FP/Altivec unavailable exception). Transactional
Memory complicates this situation as a transaction could be started
without FP/Altivec being loaded up. This causes the hardware to
checkpoint incorrect registers. Handling FP/Altivec unavailable
exceptions while a thread is transactional requires a reclaim and
recheckpoint to ensure the CPU has correct state for both sets of
registers.
tm_reclaim() has optimisations to not always save the FP/Altivec
registers to the checkpointed save area. This was originally done
because the caller might have information that the checkpointed
registers aren't valid due to lazy save and restore. We've also been a
little vague as to how tm_reclaim() leaves the FP/Altivec state since it
doesn't necessarily always save it to the thread struct. This has lead
to an (incorrect) assumption that it leaves the checkpointed state on
the CPU.
tm_recheckpoint() has similar optimisations in reverse. It may not
always reload the checkpointed FP/Altivec registers from the thread
struct before the trecheckpoint. It is therefore quite unclear where it
expects to get the state from. This didn't help with the assumption
made about tm_reclaim().
This patch is a minimal fix for ease of backporting. A more correct fix
which removes the msr parameter to tm_reclaim() and tm_recheckpoint()
altogether has been upstreamed to apply on top of this patch.
Fixes: dc3106690b ("powerpc: tm: Always use fp_state and vr_state to
store live registers")
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Lazy save and restore of FP/Altivec means that a userspace process can
be sent to userspace with FP or Altivec disabled and loaded only as
required (by way of an FP/Altivec unavailable exception). Transactional
Memory complicates this situation as a transaction could be started
without FP/Altivec being loaded up. This causes the hardware to
checkpoint incorrect registers. Handling FP/Altivec unavailable
exceptions while a thread is transactional requires a reclaim and
recheckpoint to ensure the CPU has correct state for both sets of
registers.
Lazy save and restore of FP/Altivec cannot be done if a process is
transactional. If a facility was enabled it must remain enabled whenever
a thread is transactional.
Commit dc16b553c9 ("powerpc: Always restore FPU/VEC/VSX if hardware
transactional memory in use") ensures that the facilities are always
enabled if a thread is transactional. A bug in the introduced code may
cause it to inadvertently enable a facility that was (and should remain)
disabled. The problem with this extraneous enablement is that the
registers for the erroneously enabled facility have not been correctly
recheckpointed - the recheckpointing code assumed the facility would
remain disabled.
Further compounding the issue, the transactional {fp,altivec,vsx}
unavailable code has been incorrectly using the MSR to enable
facilities. The presence of the {FP,VEC,VSX} bit in the regs->msr simply
means if the registers are live on the CPU, not if the kernel should
load them before returning to userspace. This has worked due to the bug
mentioned above.
This causes transactional threads which return to their failure handler
to observe incorrect checkpointed registers. Perhaps an example will
help illustrate the problem:
A userspace process is running and uses both FP and Altivec registers.
This process then continues to run for some time without touching
either sets of registers. The kernel subsequently disables the
facilities as part of lazy save and restore. The userspace process then
performs a tbegin and the CPU checkpoints 'junk' FP and Altivec
registers. The process then performs a floating point instruction
triggering a fp unavailable exception in the kernel.
The kernel then loads the FP registers - and only the FP registers.
Since the thread is transactional it must perform a reclaim and
recheckpoint to ensure both the checkpointed registers and the
transactional registers are correct. It then (correctly) enables
MSR[FP] for the process. Later (on exception exist) the kernel also
(inadvertently) enables MSR[VEC]. The process is then returned to
userspace.
Since the act of loading the FP registers doomed the transaction we know
CPU will fail the transaction, restore its checkpointed registers, and
return the process to its failure handler. The problem is that we're
now running with Altivec enabled and the 'junk' checkpointed registers
are restored. The kernel had only recheckpointed FP.
This patch solves this by only activating FP/Altivec if userspace was
using them when it entered the kernel and not simply if the process is
transactional.
Fixes: dc16b553c9 ("powerpc: Always restore FPU/VEC/VSX if hardware
transactional memory in use")
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The OPAL calls performed in this driver shouldn't be using
opal_async_wait_response() as this performs a wait_event() which, on
long running OPAL calls could result in hung task warnings. wait_event()
prevents timely signal delivery which is also undesirable.
This patch also attempts to quieten down the use of dev_err() when
errors haven't actually occurred and also to return better information up
the stack rather than always -EIO.
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Also export opal_error_code() so that it can be used in modules
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch adds an _interruptible version of opal_async_wait_response().
This is useful when a long running OPAL call is performed on behalf of
a userspace thread, for example, the opal_flash_{read,write,erase}
functions performed by the powernv-flash MTD driver.
It is foreseeable that these functions would take upwards of two
minutes causing the wait_event() to block long enough to cause hung
task warnings. Furthermore, wait_event_interruptible() is preferable
as otherwise there is no way for signals to stop the process which is
going to be confusing in userspace.
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Parallel sensor reads could run out of async tokens due to
opal_get_sensor_data grabbing tokens but then doing the sensor
read behind a mutex, essentially serializing the (possibly
asynchronous and relatively slow) sensor read.
It turns out that the mutex isn't needed at all, not only
should the OPAL interface allow concurrent reads, the implementation
is certainly safe for that, and if any sensor we were reading
from somewhere isn't, doing the mutual exclusion in the kernel
is the wrong place to do it, OPAL should be doing it for the kernel.
So, remove the mutex.
Additionally, we shouldn't be printing out an error when we don't
get a token as the only way this should happen is if we've been
interrupted in down_interruptible() on the semaphore.
Reported-by: Robert Lippert <rlippert@google.com>
Signed-off-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Future work will add an opal_async_wait_response_interruptible()
which will call wait_event_interruptible(). This work requires extra
token state to be tracked as wait_event_interruptible() can return and
the caller could release the token before OPAL responds.
Currently token state is tracked with two bitfields which are 64 bits
big but may not need to be as OPAL informs Linux how many async tokens
there are. It also uses an array indexed by token to store response
messages for each token.
The bitfields make it difficult to add more state and also provide a
hard maximum as to how many tokens there can be - it is possible that
OPAL will inform Linux that there are more than 64 tokens.
Rather than add a bitfield to track the extra state, rework the
internals slightly.
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
[mpe: Fix __opal_async_get_token() when no tokens are free]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There are no callers of both __opal_async_get_token() and
__opal_async_release_token().
This patch also removes the possibility of "emergency through
synchronous call to __opal_async_get_token()" as such it makes more
sense to initialise opal_sync_sem for the maximum number of async
tokens.
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Because the MTD core might split up a read() or write() from userspace
into several calls to the driver, we may fail to get a token but already
have done some work, best to return -EINTR back to userspace and have
them decide what to do.
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powernv_flash_probe() has pointless goto statements which jump to the
end of the function to simply return a variable. Rather than checking
for error and going to the label, just return the error as soon as it is
detected.
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
While this driver expects to interact asynchronously, OPAL is well
within its rights to return OPAL_SUCCESS to indicate that the operation
completed without the need for a callback. We shouldn't treat
OPAL_SUCCESS as an error rather we should wrap up and return promptly to
the caller.
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
BUG_ON() should be reserved in situations where we can not longer
guarantee the integrity of the system. In the case where
powernv_flash_async_op() receives an impossible op, we can still
guarantee the integrity of the system.
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The current code checks the completion map to look for the first token
that is complete. In some cases, a completion can come in but the
token can still be on lease to the caller processing the completion.
If this completed but unreleased token is the first token found in the
bitmap by another tasks trying to acquire a token, then the
__test_and_set_bit call will fail since the token will still be on
lease. The acquisition will then fail with an EBUSY.
This patch reorganizes the acquisition code to look at the
opal_async_token_map for an unleased token. If the token has no lease
it must have no outstanding completions so we should never see an
EBUSY, unless we have leased out too many tokens. Since
opal_async_get_token_inrerruptible is protected by a semaphore, we
will practically never see EBUSY anymore.
Fixes: 8d72482322 ("powerpc/powernv: Infrastructure to support OPAL async completion")
Signed-off-by: William A. Kennington III <wak@google.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This interface is inefficient and deprecated because of the y2038
overflow.
ktime_get_seconds() is an appropriate replacement here, since it
has sufficient granularity but is more efficient and uses monotonic
time.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Presently the PSL9 specific cxl_stop_trace_psl9() only stops the RX0
traces on the CXL adapter when a PSL error irq is triggered. The patch
updates the function to stop all the traces arrays and move them to
the FIN state. The implementation issues the mmio to TRACECFG register
to stop the trace array iff it already not in FIN state. This prevents
the issue of trace data being reset in case of multiple stop mmio
issued for a single trace array.
Also the patch does some refactoring of existing cxl_stop_trace_psl9()
and cxl_stop_trace_psl8() functions by moving them to 'pci.c' from
'debugfs.c' file and marking them as static.
Signed-off-by: Vaibhav Jain <vaibhav@linux.vnet.ibm.com>
Acked-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Take advantage of stack_depth tracking, originally introduced for
x64, in powerpc JIT as well. Round up allocated stack by 16 bytes
to make sure it stays aligned for functions called from JITed bpf
program.
Signed-off-by: Sandipan Das <sandipan@linux.vnet.ibm.com>
Reviewed-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently when we take a TM Bad Thing program check exception, we
search the bug table to see if the program check was generated by a
WARN/WARN_ON etc.
That makes no sense, the WARN macros use trap instructions, which
should never generate a TM Bad Thing exception. If they ever did that
would be a bug and we should oops.
We do have some hand-coded bugs in tm.S, using EMIT_BUG_ENTRY, but
those are all BUGs not WARNs, and they all use trap instructions
anyway. Almost certainly this check was incorrectly copied from the
REASON_TRAP handling in the same function.
Remove it.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-By: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently if the hardware supports the radix MMU we will use
it, *unless* "disable_radix" is passed on the kernel command line.
However some users would like the reverse semantics. ie. The kernel
uses the hash MMU by default, unless radix is explicitly requested on
the command line.
So add a CONFIG option to choose whether we use radix by default or
not, and expand the disable_radix command line option to allow
"disable_radix=no" which *enables* radix.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
CONFIG_PPC_STD_MMU_64 indicates support for the "standard" powerpc MMU
on 64-bit CPUs. The "standard" MMU refers to the hash page table MMU
found in "server" processors, from IBM mainly.
Currently CONFIG_PPC_STD_MMU_64 is == CONFIG_PPC_BOOK3S_64. While it's
annoying to have two symbols that always have the same value, it's not
quite annoying enough to bother removing one.
However with the arrival of Power9, we now have the situation where
CONFIG_PPC_STD_MMU_64 is enabled, but the kernel is running using the
Radix MMU - *not* the "standard" MMU. So it is now actively confusing
to use it, because it implies that code is disabled or inactive when
the Radix MMU is in use, however that is not necessarily true.
So s/CONFIG_PPC_STD_MMU_64/CONFIG_PPC_BOOK3S_64/, and do some minor
formatting updates of some of the affected lines.
This will be a pain for backports, but c'est la vie.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The last user of CPU_FTR_ICSWX was removed in commit
6ff4d3e966 ("powerpc: Remove old unused icswx based coprocessor
support"), so free the bit up for future use.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
IPIC Status is provided by register IPIC_SERSR and not by IPIC_SERMR
which is the mask register.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In order to make generic IOV code work, the physical function IOV BAR
should start from offset of the first VF. Since M64 segments share
PE number space across PHB, and some PEs may be in use at the time
when IOV is enabled, the existing code shifts the IOV BAR to the index
of the first PE/VF. This creates a hole in IOMEM space which can be
potentially taken by some other device.
This reserves a temporary hole on a parent and releases it when IOV is
disabled; the temporary resources are stored in pci_dn to avoid
kmalloc/free.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When a vdevice is DLPAR removed from the system the vio subsystem
doesn't bother unmapping the virq from the irq_domain. As a result we
have a virq mapped to a hardware irq that is no longer valid for the
irq_domain. A side effect is that we are left with /proc/irq/<irq#>
affinity entries, and attempts to modify the smp_affinity of the irq
will fail.
In the following observed example the kernel log is spammed by
ics_rtas_set_affinity errors after the removal of a VSCSI adapter.
This is a result of irqbalance trying to adjust the affinity every 10
seconds.
rpadlpar_io: slot U8408.E8E.10A7ACV-V5-C25 removed
ics_rtas_set_affinity: ibm,set-xive irq=655385 returns -3
ics_rtas_set_affinity: ibm,set-xive irq=655385 returns -3
This patch fixes the issue by calling irq_dispose_mapping() on the
virq of the viodev on unregister.
Fixes: f2ab621996 ("powerpc/pseries: Add PFO support to the VIO bus")
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
According to the architecture, the process table entry cache must be
flushed with tlbie RIC=2.
Currently the process table entry is set to invalid right before the
PID is returned to the allocator, with no invalidation. This works on
existing implementations that are known to not cache the process table
entry for any except the current PIDR.
It is architecturally correct and cleaner to invalidate with RIC=2
after clearing the process table entry and before the PID is returned
to the allocator. This can be done in arch_exit_mmap that runs before
the final flush, and to ensure the final flush (fullmm) is always a
RIC=2 variant.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Preempt should be consistently disabled for mm_is_thread_local tests,
so bring the rest of these under preempt_disable().
Preempt does not need to be disabled for the mm->context.id tests,
which allows simplification and removal of gotos.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Close the recoverability gap for OPAL calls by using FIXUP_ENDIAN_HV
in the return path.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add an HV variant of FIXUP_ENDIAN which uses HSRR[01] and does not
clear MSR[RI], which improves recoverability.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When returning from an exception to a soft-enabled context, pending
IRQs are replayed but IRQ tracing is not reset, so a number of them
can get chained together into the same IRQ-disabled trace.
Fix this by having __check_irq_replay re-set IRQ trace. This is
conceptually where we respond to the next interrupt, so it fits the
semantics of the IRQ tracer.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
If the host takes a system reset interrupt while a guest is running,
the CPU must exit the guest before processing the host exception
handler.
After this patch, taking a sysrq+x with a CPU running in a guest
gives a trace like this:
cpu 0x27: Vector: 100 (System Reset) at [c000000fdf5776f0]
pc: c008000010158b80: kvmppc_run_core+0x16b8/0x1ad0 [kvm_hv]
lr: c008000010158b80: kvmppc_run_core+0x16b8/0x1ad0 [kvm_hv]
sp: c000000fdf577850
msr: 9000000002803033
current = 0xc000000fdf4b1e00
paca = 0xc00000000fd4d680 softe: 3 irq_happened: 0x01
pid = 6608, comm = qemu-system-ppc
Linux version 4.14.0-rc7-01489-g47e1893a404a-dirty #26 SMP
[c000000fdf577a00] c008000010159dd4 kvmppc_vcpu_run_hv+0x3dc/0x12d0 [kvm_hv]
[c000000fdf577b30] c0080000100a537c kvmppc_vcpu_run+0x44/0x60 [kvm]
[c000000fdf577b60] c0080000100a1ae0 kvm_arch_vcpu_ioctl_run+0x118/0x310 [kvm]
[c000000fdf577c00] c008000010093e98 kvm_vcpu_ioctl+0x530/0x7c0 [kvm]
[c000000fdf577d50] c000000000357bf8 do_vfs_ioctl+0xd8/0x8c0
[c000000fdf577df0] c000000000358448 SyS_ioctl+0x68/0x100
[c000000fdf577e30] c00000000000b220 system_call+0x58/0x6c
--- Exception: c01 (System Call) at 00007fff76868df0
SP (7fff7069baf0) is in userspace
Fixes: e36d0a2ed5 ("powerpc/powernv: Implement NMI IPI with OPAL_SIGNAL_SYSTEM_RESET")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>