Instead of setting err=true and checking this to determine when to free
the raw_packet near the end of the function, simply kfree and return
immediately. The resulting code is a bit cleaner and has one less
variable. This also resolves a subtle bug in the ipv4 case which could
fail to add the first filter and then never free the memory, resulting
in a small memory leak.
Change-ID: I7583aac033481dc794b4acaa14445059c8930ff1
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Avinash Dayanand <avinash.dayanand@intel.com>
Reviewed-by: Alan Brady <alan.brady@intel.com>
Reviewed-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Refactor the exit flow of the i40e_add_fdir_ethtool function. Move the
input_label to the end of the function, removing the dependency on
having a non-zero return value. Add a comment explaining why it is ok
not to free the fdir data structure, because the structure is now stored
in the fdir_filter_list.
Change-Id: I723342181d59cd0c9f3b31140c37961ba37bb242
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The code originally included src_ip and dst_ip with enough space to
support ipv6 filters. However, no actual support for ipv6 filters has
been implemented. Thus, remove the arrays and just use __be32 values.
Should ipv6 support be added in the future, we can replace these with
a union that has sizes for both values.
Change-Id: I1bc04032244a80eb6ebc8a4e6c723a4a665c1dd5
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The firmware expects the port numbers for offloaded UDP tunnels in
Little Endian format. We accidentally sent the value in Big Endian
format which obviously will cause the wrong port number to be put into
the UDP tunnels list. This results in VxLAN and Geneve tunnel Rx
offloads being essentially disabled, unless the port number happens to
be identical after byte swapping. Note that i40e_aq_add_udp_tunnel()
will byteswap the parameter from host order into Little Endian so we
don't need worry about passing strictly a __le16 value to the command.
This patch essentially reverts b3f5c7bc88 ("i40e: Fix for extra byte
swap in tunnel setup", 2016-08-24), but in a way that makes the result
much more clear to the reader.
Fixes: b3f5c7bc88 ("i40e: Fix for extra byte swap in tunnel setup", 2016-08-24)
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Williams, Mitch A <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In the 'commit ebee76f7fa ("ath10k: allow setting coverage class")',
it inherits the design and the address offset from ath9k, but the address
is not applicable to QCA6174, which leads to a random crash while doing the
resume() operation, since the set_coverage_class.ops will be called from
ieee80211_reconfig() when resume() (if the wow is not configured).
Fix the incorrect address offset here to avoid the random crash.
Verified on QCA6174/hw3.0 with firmware WLAN.RM.4.4-00022-QCARMSWPZ-2.
kvalo: this also seems to fix a regression with firmware restart.
Fixes: ebee76f7fa ("ath10k: allow setting coverage class")
Cc: <stable@vger.kernel.org> # v4.10
Signed-off-by: Ryan Hsu <ryanhsu@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There was a typo that I had left in the code comments for the igb and ixgbe
functions that enabled build_skb support.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This reverts commit f9d40f6a99 ("igb: Revert support for build_skb in
igb") and adds a few changes to update it to work with the latest version
of igb. We are now able to revert the removal of this due to the fact
that with the recent changes to the page count and the use of
DMA_ATTR_SKIP_CPU_SYNC we can make the pages writable so we should not be
invalidating the additional data added when we call build_skb.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
At this point we have 2 to 3 paths that can be taken depending on what Rx
modes are enabled. In order to better support that and improve the
maintainability I am breaking out the common bits from those paths and
making them into their own functions.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
With the size of the frame limited we can now write to an offset within the
buffer instead of having to write at the very start of the buffer. The
advantage to this is that it allows us to leave padding room for things
like supporting XDP in the future.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for using 3K buffers in order 1 pages the same way
we were using 2K buffers in 4K pages. We are reserving 1K of room for now
to have space available for future headroom and tailroom when we enable
build_skb support.
One side effect of this patch is that we can end up using a larger buffer
if jumbo frames is enabled. The impact shouldn't be too great, but it
could hurt small packet performance for UDP workloads if jumbo frames is
enabled as the truesize of frames will be larger.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since there are potential drawbacks to the new Rx allocation approach I
thought it best to add a "chicken bit" so that we can turn the feature off
if in the event that a problem is found.
It also provides a means of validating the legacy Rx path in the event that
we are forced to fall back. At some point in the future when we are
convinced we don't need it anymore we might be able to drop the legacy-rx
flag.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Update the handling of page addresses so that we always refer to them using
a void pointer, and try to use the consistent name of va indicating we are
working with a virtual address.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We only need to sync the size of the frame that is read to test. We don't
need to sync the entire Rx buffer. This way the testing is more consistent
with how we handle things in the receive path.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In order to support the use of build_skb going forward it will be necessary
to place a maximum limit on the amount of data we can receive when jumbo
frames is not enabled. In order to do this I am adding a new upper limit
for receive based on the size of a 2K buffer minus padding.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In the case of the Tx rings we need to only clear the Tx buffer_info when
we are resetting the rings. Ideally we do this when we configure the ring
to bring it back up instead of when we are taking it down in order to avoid
dirtying pages we don't need to.
In addition we don't need to clear the Tx descriptor ring since we will
fully repopulate it when we begin transmitting frames and next_to_watch can
be cleared to prevent the ring from being cleaned beyond that point instead
of needing to touch anything in the Tx descriptor ring.
Finally with these changes we can avoid having to reset the skb member of
the Tx buffer_info structure in the cleanup path since the skb will always
be associated with the first buffer which has next_to_watch set.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that instead of going through the entire ring on Rx
cleanup we only go through the region that was designated to be cleaned up
and stop when we reach the region where new allocations should start.
In addition we can avoid having to perform a memset on the Rx buffer_info
structures until we are about to start using the ring again. By deferring
this we can avoid dirtying the cache any more than we have to which can
help to improve the time needed to bring the interface down and then back
up again in a reset or suspend/resume cycle.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that we use the length of the packet instead of the
DD status bit to determine if a new descriptor is ready to be processed.
The obvious advantage is that it cuts down on reads as we don't really even
need the DD bit if going from a 0 to a non-zero value on size is enough to
inform us that the packet has been completed.
In addition I have updated the code so that we only reset the Rx descriptor
length for descriptor zero when resetting a ring instead of having to do a
memset with 0 over the entire ring. By doing this we can save some time on
initialization.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since we are already using DMA attributes in igb for Rx there is no reason
why we can't also apply DMA_ATTR_WEAK_ORDERING which is needed on some
platforms to improve performance.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Information reported to ethtool about link modes is wrong for 25G NIC. Fix
it by checking for presence of 25G NIC, checking the link speed reported by
NIC firmware, and then assigning proper values to the
ethtool_link_ksettings struct.
Signed-off-by: Manish Awasthi <manish.awasthi@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add some short description of how callback's and NAPI interoperate.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the argument to channel callback from the channel pointer
to the internal data structure containing per-channel info.
This avoids any possible races when callback happens during
initialization and makes IRQ code simpler.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When device is being setup on boot, there is a small race where
network device callback is registered, but the netvsc_device pointer
is not set yet. This can cause a NULL ptr dereference if packet
arrives during this window.
Fixes: 46b4f7f5d1 ("netvsc: eliminate per-device outstanding send counter")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pointer array for the tx/rx sub crqs should be free'ed when
releasing the tx/rx sub crqs.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sunvnet netdev is connected to the controlling ldom's vswitch
for network bridging. However, for higher performance between ldoms,
there also is a channel between each client ldom. These connections are
represented in the sunvnet driver by a queue for each ldom. The driver
uses select_queue to tell the stack which queue to use by tracking the mac
addresses on the other end of each port. When a connected ldom shuts down,
the driver receives an LDC_EVENT_RESET and the port is removed from the
driver, thus a queue with no ldom on the other end will never be selected
for Tx.
The driver was trying to reinforce the "don't use this queue" notion with
netif_tx_stop_queue() and netif_tx_wake_queue(), which really should only
be used to signal a Tx queue is full (aka XOFF). This misuse of queue
state resulted in NETDEV WATCHDOG messages and lots of unnecessary calls
into the driver's tx_timeout handler. Simply removing these takes care
of the problem.
Orabug: 25190537
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure multicast packets get counted in the device.
Orabug: 25190537
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Track our used and unused queue indexies correctly. Otherwise, as ports
dropped out and returned, they all eventually ended up with the same
queue index.
Orabug: 25190537
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In this driver, there is a "port" created for the connection to each of
the other ldoms; a netdev queue is mapped to each port, and they are
collected under a single netdev. The generic netdev statistics show
us all the traffic in and out of our network device, but don't show
individual queue/port stats. This patch breaks out the traffic counts
for the individual ports and gives us a little view into the state of
those connections.
Orabug: 25190537
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an ldom VM is bound, the network vswitch infrastructure is set up for
it, but was being forced 'UP' by the userland switch configuration script.
When 'UP' but not actually connected to a running VM, the ipv6 neighbor
probes fail (not a horrible thing) and start cluttering up the kernel logs.
Funny thing: these are debug messages that never actually show up, but
we do see the net_ratelimited messages that say N callbacks were
suppressed.
This patch defers the netif_carrier_on() until an actual link has been
established with the VM, as indicated by receiving an LDC_EVENT_UP from
the underlying LDC protocol. Similarly, we take the link down when we
see the LDC_EVENT_RESET. Now when we see the ndo_open(), we reset the
link to get things talking again.
Orabug: 25525312
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cut-n-paste enablement of 802.3ad bonding on 25G NICs, which currently
report 0 as their bandwidth.
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: netdev@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the aquantia device mtu is changed the net_device structure is not
updated. As a result the ip command does not properly reflect the mtu change.
Commit 5513e16421 incorrectly assumed that __dev_set_mtu() was making the
assignment ndev->mtu = new_mtu; This is not true in the case where the driver
has a ndo_change_mtu routine.
Fixes: 5513e16421 ("net: ethernet: aquantia: Fixes for aq_ndev_change_mtu")
Cc: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: David Arcari <darcari@redhat.com>
Tested-by: Pavel Belous <pavel.belous@aquantia.com>
Reviewed-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All IRQs owned by the PF and VF drivers share the same nondescript name
"octeon"; this makes it difficult to setup interrupt affinity.
Change the IRQ names to reflect their specific purpose:
LiquidIO<id>-<func>-<type>-<queue pair num>
Examples:
LiquidIO0-pf0-rxtx-3
LiquidIO1-vf1-rxtx-0
LiquidIO0-pf0-aux
We cannot use netdev->name for naming the IRQs because:
1. Early during init, the PF and VF drivers require interrupts to
send/receive control data from the NIC firmware; so the PF and VF
must request IRQs long before the netdev struct is registered.
2. The IRQ name can only be specified at the time it is requested.
It cannot be changed after that.
Signed-off-by: Rick Farrington <ricardo.farrington@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: Satanand Burla <satananda.burla@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove invalid call to dma_sync_single_for_cpu() because previous DMA
allocation was coherent--not streaming. Remove code that references fields
in struct list_head; replace it with calls to list_empty() and
list_first_entry(). Also, add comment to clarify complicated if statement.
Signed-off-by: Rick Farrington <ricardo.farrington@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: Derek Chickles <derek.chickles@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some Hypervisors detach VFs from VMs by instantly causing an FLR event
to be generated for a VF.
In the mlx4 case, this will cause that VF's comm channel to be disabled
before the VM has an opportunity to invoke the VF device's "shutdown"
method.
For such Hypervisors, there is a race condition between the VF's
shutdown method and its internal-error detection/reset thread.
The internal-error detection/reset thread (which runs every 5 seconds) also
detects a disabled comm channel. If the internal-error detection/reset
flow wins the race, we still get delays (while that flow tries repeatedly
to detect comm-channel recovery).
The cited commit fixed the command timeout problem when the
internal-error detection/reset flow loses the race.
This commit avoids the unneeded delays when the internal-error
detection/reset flow wins.
Fixes: d585df1c5c ("net/mlx4_core: Avoid command timeouts during VF driver device shutdown")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Reported-by: Simon Xiao <sixiao@microsoft.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allows the BCMA version of the bgmac driver to obtain MAC address
from the device tree. If no MAC address is specified there, then
the previous behavior (obtaining MAC address from SPROM) is
used.
Signed-off-by: Steve Lin <steven.lin1@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CONFIG_8xx is being deprecated. Since the includes dependent on
CONFIG_8xx are useless, just drop them.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add basic support for handling suspend and resume.
Signed-off-by: Jane Li <jiel@marvell.com>
Reviewed-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that port netdevs can be enslaved to a VRF master we need to make
sure the device's routing tables won't be flushed upon the insertion of
a l3mdev rule.
Note that we assume the notified l3mdev rule is a simple rule as used by
the VRF master. We don't check for the presence of other selectors such
as 'iif' and 'oif'.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a similar fashion to the previous patch, allow bridges and VLAN
devices on top of bridges to be enslaved to a VRF master device.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow port netdevs, LAG and VLAN devices stacked on top of these to be
enslaved to a VRF master device.
Upon enslavement, create a router interface (RIF) for the enslaved
netdev and associate it with a virtual router (VR) based on the VRF's
table ID.
If a RIF already exists for the netdev (f.e., due to the existence of an
IP address), then it's deleted and a new one is created with the
appropriate VR binding.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We usually destroy the netdev's router interface (RIF) when the last IP
address is removed from it.
However, we shouldn't do that if it's enslaved to an L3 master device.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a router interface (RIF) is created due to a netdev being enslaved
to a VRF master, then it should be associated with the appropriate
virtual router (VR) and not the default one.
If netdev is a VRF slave, lookup the VR based on the VRF's table ID.
Otherwise default to the MAIN table.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow listeners of the subsequent CHANGEUPPER notification to retrieve
the VRF's table ID by calling l3mdev_fib_table() with the slave netdev.
Without this change, the netdev won't be considered an L3 slave and the
function would return 0.
This is consistent with other master device such as bridge and bond that
set the slave's private flag before linking. It also makes
do_vrf_{add,del}_slave() symmetric.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit c3852ef7f2 ("ipv4: fib: Replay events when registering FIB
notifier") we dumped the FIB tables and replayed the events to the
passed notification block.
However, we merely sent a RULE_ADD notification in case custom rules
were in use. As explained in previous patches, this approach won't work
anymore. Instead, we should notify the caller about all the FIB rules
and let it act accordingly.
Upon registration to the FIB notification chain, replay a RULE_ADD
notification for each programmed FIB rule, custom or not. The integrity
of the dump is ensured by the mechanism introduced in the above
mentioned commit.
Prevent regressions by making sure current listeners correctly sanitize
the notified rules.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace &tp->napi with napi and tp->netdev with netdev.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We manually init wakeup info, but we don't detach it on device removal.
This means that if we (for example) rmmod + modprobe the driver, the
device framework might return -EEXIST the second time, and we'll
complain in the logs:
[ 839.311881] mwifiex_pcie 0000:01:00.0: fail to init wakeup for mwifiex
AFAICT, there's no other negative effect.
But we can fix this by disabling wakeup on remove, similar to what a few
other drivers do (e.g., the power supply framework).
This code (and bug) has existed on SDIO for a while, but it got moved
around and enabled for PCIe with commit 853402a008 ("mwifiex: Enable
WoWLAN for both sdio and pcie").
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The mwifiex_dbg() log handler utilizes the struct device in
adapter->dev. Without it, it decides not to print anything.
As of commit 2e02b58142 ("mwifiex: Allow mwifiex early access to device
structure"), we started assigning that pointer only after we finished
mwifiex_register() -- this effectively neuters any mwifiex_dbg() logging
done before this point.
Let's move the device assignment into mwifiex_register().
Fixes: 2e02b58142 ("mwifiex: Allow mwifiex early access to device structure")
Cc: Rajat Jain <rajatja@google.com>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When PCIe FLR support was added, much of the remove/release code for
PCIe was migrated to ->down_dev(), but ->down_dev() is never called for
device removal. Let's refactor the cleanup to be done in both cases.
Also, drop the comments above mwifiex_cleanup_pcie(), because they were
clearly wrong, and it's better to have clear and obvious code than to
detail the code steps in comments anyway.
Fixes: 4c5dae59d2 ("mwifiex: add PCIe function level reset support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When a station is asleep, the fw will set it as "asleep".
All queues that are used only by one station will be stopped by
the fw.
In pre-DQA mode this was relevant for aggregation queues. However,
in DQA mode a queue is owned by one station only, so all queues
will be stopped.
As a result, we don't expect to get filtered frames back to
mac80211 and don't have to maintain the entire pending_frames
state logic, the same way as we do in aggregations.
The correct behavior is to align DQA behavior with the aggregation
queue behaviour pre-DQA:
- Don't count pending frames.
- Let mac80211 know we have frames in these queues so that it can
properly handle trigger frames.
When a trigger frame is received, mac80211 tells the driver to send
frames from the queues using release_buffered_frames.
The driver will tell the fw to let frames out even if the station
is asleep. This is done by iwl_mvm_sta_modify_sleep_tx_count.
Reported-and-tested-by: Jens Axboe <axboe@kernel.dk>
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch implements workaround for errata 10GE_8 and ENET_11:
"HW reports length error for valid 64 byte frames with len <46 bytes"
by recovering them from error.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Quan Nguyen <qnguyen@apm.com>
Signed-off-by: Toan Le <toanle@apm.com>
Tested-by: Fushen Chen <fchen@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements workaround for errata 10GE_1:
10Gb Ethernet port FIFO threshold default values are incorrect.
Signed-off-by: Quan Nguyen <qnguyen@apm.com>
Signed-off-by: Toan Le <toanle@apm.com>
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Tested-by: Fushen Chen <fchen@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes Rx checksum validation logic and
adds NETIF_F_RXCSUM flag.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the wrong logical OR operation by changing it to
bit-wise OR operation.
Fixes: 3bb502f830 ("drivers: net: xgene: fix statistics counters race condition")
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Quan Nguyen <qnguyen@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the hardware checksum settings by properly program
the classifier. Otherwise, packet may be received with checksum error
on X-Gene1 SoC.
Signed-off-by: Quan Nguyen <qnguyen@apm.com>
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patches fixes a typo in the argument to xgene_enet_wr_mdio_csr().
Signed-off-by: Quan Nguyen <qnguyen@apm.com>
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer hardware does not provide a cumulative payload length when multiple
descriptors are needed to handle the data. Once the MTU increases beyond
the size that can be handled by a single descriptor, the SKB does not get
built properly by the driver.
The driver will now calculate the size of the data buffers used by the
hardware. The first buffer of the first descriptor is for packet headers
or packet headers and data when the headers can't be split. Subsequent
descriptors in a multi-descriptor chain will not use the first buffer. The
second buffer is used by all the descriptors in the chain for payload data.
Based on whether the driver is processing the first, intermediate, or last
descriptor it can calculate the buffer usage and build the SKB properly.
Tested and verified on both old and new hardware.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Suspending the PHY would be putting it in a low power state where it
may no longer allow us to do Wake-on-LAN.
Fixes: cc013fb488 ("net: bcmgenet: correctly suspend and resume PHY device")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that DSA has ageing time limits, specify them when registering a
switch so that out-of-range values are handled correctly by the core.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reported-by: Jason Cobham <jcobham@questertangent.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The configurable priority to traffic class mapping and the user specified
queue ranges are used to configure the traffic class, overriding the
hardware defaults when the 'hw' option is set to 0. However, when the 'hw'
option is non-zero, the hardware QOS defaults are used.
This patch makes it so that we can pass the data the user provided to
ndo_setup_tc. This allows us to pull in the queue configuration if the
user requested it as well as any additional hardware offload type
requested by using a value other than 1 for the hw value.
Finally it also provides a means for the device driver to return the level
supported for the offload type via the qopt->hw value. Previously we were
just always assuming the value to be 1, in the future values beyond just 1
may be supported.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At the end of the timeout loop, retries will always be zero so
the check for zero is redundant so remove it. Also replace
printk with pr_err as recommended by checkpatch.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch prepares the main ISR for multiple queues.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch configures TSO for all available tx queues.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch prepares the DMA initialization process for multiple queues.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch prepares RX and TX set tail functions for multiple queues.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch prepares tx and rx ring length configuration for multiple queues.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds rx watchdog configuration for all queues.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch prepares DMA interrupts treatment for multiple queues.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch prepares stmmac_err for multiple queues.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch prepares the RX/TX DMA stop/start process for multiple queues.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch prepares the DMA IRQ enable/disable process for multiple queues.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch prepares DMA Operation Mode configuration for multiple queues.
The work consisted on breaking the DMA operation Mode configuration function
into RX and TX scope and adapting its mechanism in stmmac_main.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2017-03-15
This series contains updates to i40e and i40evf only.
Aaron fixes an issue on x710 devices where simultaneous read accesses
were interfering with each other, so make sure all devices acquire the
NVM lock before reads on all devices.
Shannon adds Wake On LAN support feature for x722 devices and cleaned
up the opcodes so that they are in numerical order.
Mitch adds a client interface to the VF driver, in preparation for the
upcoming RDMA-capable hardware (and client driver). Cleaned up the
client interface in the PF driver, since it was originally over
engineered to handle multiple clients on multiple netdevs, but that
did not happen and now there will be one client per driver, so apply
the "KISS" (Keep It Simple & Stupid) to the i40e client interface.
Bumped the number of MAC filters an untrusted VF can create.
Jake fixes an issue where a recent refactor of queue pairs accidentally
added all remaining vecotrs to the num_lan_msix which can adversely
affect performance.
Lihong fixes an ethtool issue with x722 devices where "-e" will error
out since its EEPROM has a scope limit at offset 0x5B9FFF, so set the
EEPROM length to the scope limit. Also fixed an issue where RSS
offloading only worked on PF0.
Filip cleans up and clarifies code comment so there is no confusion
about MAC/VLAN filter initialization routine.
Alex adds support for DMA_ATTR_SKIP_CPU_SYNC and DMA_ATTR_WEAK_ORDERING,
which improves performance on architectures that implement either one.
Harshitha cleans up confusion on flags disabled due to hardware limitation
versus featured disabled by the user, so rename auto_disable_flags to
hw_disabled_flags to avoid the confusion.
v2: Merged patch #1 and #4 in first version to make patch #3 in this
series based on feedback from David Miller.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes netdev->features for Extended Socket network device.
Currently Extended Socket network device's netdev->feature claims
NETIF_F_HW_CSUM, however this is completely wrong. There's no feature
of checksum offloading.
That causes invalid TCP/UDP checksum and packet rejection when IP
forwarding from Extended Socket network device to other network device.
NETIF_F_HW_CSUM should be omitted.
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/broadcom/genet/bcmgenet.c
net/core/sock.c
Conflicts were overlapping changes in bcmgenet and the
lockdep handling of sockets.
Signed-off-by: David S. Miller <davem@davemloft.net>
A previous commit introduced a field that tracks the features
that are disabled due to HW resource limitations as opposed
to the featured disabled by the user. This patch changes the
name of the field to make it more readable since it might get
confusing when looking at code containing both the flags
field and the auto_disable_features field together.
Change-ID: Idcc9888659698f6fe3ccff17c8c3f09b5026f708
Signed-off-by: Harshitha Ramamurthy <harshitha.ramamurthy@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Our original filter limit of 8 was based on behavior that we saw from
Linux VMs. Now we're running Other Operating Systems under KVM and we
see that they commonly use more MAC filters. Since it seems weird to
require people to enable trusted VFs just to boot their OS, bump the
number of filters allowed by default.
Change-ID: I76b2dcb2ad6017e39231ad3096c3fb6f065eef5e
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for DMA_ATTR_SKIP_CPU_SYNC and
DMA_ATTR_WEAK_ORDERING. By enabling both of these for the Rx path we
are able to see performance improvements on architectures that implement
either one due to the fact that page mapping and unmapping only has to
sync what is actually being used instead of the entire buffer. In addition
by enabling the weak ordering attribute enables a performance improvement
for architectures that can associate a memory ordering with a DMA buffer
such as Sparc.
Change-ID: If176824e8231c5b24b8a5d55b339a6026738fc75
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch clarifies the reason for removal of automatically
firmware-generated filter and explicit addition of filter which
accepts frames with any VLAN id.
Change-ID: Iabf180b6d61c4d8a36d3bcf8457c377a6f2aca0e
Signed-off-by: Filip Sadowski <filip.sadowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes the issue that RSS offloading only works on PF0 by
using the direct register writing of the hash keys for the VFs instead
of using the admin queue command to do so.
Change-ID: Ia02cda7dbaa23def342e8786097a2c03db6f580b
Signed-off-by: Lihong Yang <lihong.yang@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently ethtool -e will error out with a X722 interface
as its EEPROM has a scope limit at offset 0x5B9FFF.
This patch fixes the issue by setting the EEPROM length to
the scope limit to avoid NVM read failure beyond that.
Change-ID: I0b7d4dd6c7f2a57cace438af5dffa0f44c229372
Signed-off-by: Lihong Yang <lihong.yang@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is a solution to avoid adding too many queues to num_lan_msix.
A recent refactor of queue pairs accidentally added all remaining
vectors to the num_lan_msix which can have adverse performance issues,
due to enabling more queues than the number of CPU cores.
This patch removes the old calculation, and replaces it with a simple
algorithm.
1) add queue pairs up to num_online_cpus(), but capped at half of total
vectors
2) then add alternative features such as flow directory and similar
3) finally, add the remaining vectors back to queue pairs, but capped
such that the total number of queue pairs does not exceed
num_online_cpus().
Change-ID: I668abf67d5011a1248866daba8885f4ff00cb8d9
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Harshitha Ramamurthy <harshitha.ramamurthy@intel.com>
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
(KISS is Keep It Simple, Stupid. Or is it?)
The client interface vastly overengineered for what it needs to do.
It was originally designed to support multiple clients on multiple
netdevs, possibly even with multiple drivers. None of this happened,
and now we know that there will only ever be one client for i40e
(i40iw) and one for i40evf (i40iwvf). So, time for some KISS. Since
i40e and i40evf are a Dynasty, we'll simplify this one to match the
VF interface.
First, be a Destroyer and remove all of the lists and locks required
to support multiple clients. Keep one static around to keep track of
one client, and track the client instances for each netdev in the
driver's pf (or adapter) struct. Now it's Almost Human.
Since we already know the client type is iWarp, get rid of any checks
for this. Same for VSI type - it's always going to be the same type,
so it's just a Parasite.
While we're at it, fix up some comments. This makes the function
headers actually match the functions.
These changes reduce code complexity, simplify maintenance,
squash some lurking timing bugs, and allow us to Rock and Roll All
Nite.
Change-ID: I1ea79948ad73b8685272451440a34507f9a9012e
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In preparation for upcoming RDMA-capable hardware, add a client
interface to the VF driver. This is a slightly-simplified version
of the PF client interface, with the names changed to protect the
innocent.
Due to the nature of the VF<->PF interactions, the client interface
sometimes needs to call back into itself to pass messages. Because
of this, we can't use the coarse-grained locking like the PF's
client interface uses. Instead, we handle all client interactions
in a separate thread so the watchdog can still run and process
virtual channel messages.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Avinash Dayanand <avinash.dayanand@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Pull networking fixes from David Miller:
1) Ensure that mtu is at least IPV6_MIN_MTU in ipv6 VTI tunnel driver,
from Steffen Klassert.
2) Fix crashes when user tries to get_next_key on an LPM bpf map, from
Alexei Starovoitov.
3) Fix detection of VLAN fitlering feature for bnx2x VF devices, from
Michal Schmidt.
4) We can get a divide by zero when TCP socket are morphed into
listening state, fix from Eric Dumazet.
5) Fix socket refcounting bugs in skb_complete_wifi_ack() and
skb_complete_tx_timestamp(). From Eric Dumazet.
6) Use after free in dccp_feat_activate_values(), also from Eric
Dumazet.
7) Like bonding team needs to use ETH_MAX_MTU as netdev->max_mtu, from
Jarod Wilson.
8) Fix use after free in vrf_xmit(), from David Ahern.
9) Don't do UDP Fragmentation Offload on IPComp ipsec packets, from
Alexey Kodanev.
10) Properly check napi_complete_done() return value in order to decide
whether to re-enable IRQs or not in amd-xgbe driver, from Thomas
Lendacky.
11) Fix double free of hwmon device in marvell phy driver, from Andrew
Lunn.
12) Don't crash on malformed netlink attributes in act_connmark, from
Etienne Noss.
13) Don't remove routes with a higher metric in ipv6 ECMP route replace,
from Sabrina Dubroca.
14) Don't write into a cloned SKB in ipv6 fragmentation handling, from
Florian Westphal.
15) Fix routing redirect races in dccp and tcp, basically the ICMP
handler can't modify the socket's cached route in it's locked by the
user at this moment. From Jon Maxwell.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (108 commits)
qed: Enable iSCSI Out-of-Order
qed: Correct out-of-bound access in OOO history
qed: Fix interrupt flags on Rx LL2
qed: Free previous connections when releasing iSCSI
qed: Fix mapping leak on LL2 rx flow
qed: Prevent creation of too-big u32-chains
qed: Align CIDs according to DORQ requirement
mlxsw: reg: Fix SPVMLR max record count
mlxsw: reg: Fix SPVM max record count
net: Resend IGMP memberships upon peer notification.
dccp: fix memory leak during tear-down of unsuccessful connection request
tun: fix premature POLLOUT notification on tun devices
dccp/tcp: fix routing redirect race
ucc/hdlc: fix two little issue
vxlan: fix ovs support
net: use net->count to check whether a netns is alive or not
bridge: drop netfilter fake rtable unconditionally
ipv6: avoid write to a possibly cloned skb
net: wimax/i2400m: fix NULL-deref at probe
isdn/gigaset: fix NULL-deref at probe
...
Some opcodes added & reordered to be in numerical order with the
rest of the opcodes.
This patch adds admin queue structs to support Wake on LAN feature
for X722.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acquire NVM lock before reads on all devices. Previously, locks were
only used for X722 and later. Fixes an issue where simultaneous X710
NVM accesses were interfering with each other.
Change-ID: If570bb7acf958cef58725ec2a2011cead6f80638
Signed-off-by: Aaron Salter <aaron.k.salter@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This adds the necessary infrastructure changes for initializing
and working with the new series of QL41xxx adapaters.
It also adds 2 new PCI device-IDs to qede:
- 0x8070 for QL41xxx PFs
- 0x8090 for VFs spawning from QL41xxx PFs
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Missing in the initial submission, qed fails to propagate qedi's
request to enable OOO to firmware.
Fixes: fc831825f9 ("qed: Add support for hardware offloaded iSCSI")
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Need to set the number of entries in database, otherwise the logic
would quickly surpass the array.
Fixes: 1d6cff4fca ("qed: Add iSCSI out of order packet handling")
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before iterating over the the LL2 Rx ring, the ring's
spinlock is taken via spin_lock_irqsave().
The actual processing of the packet [including handling
by the protocol driver] is done without said lock,
so qed releases the spinlock and re-claims it afterwards.
Problem is that the final spin_lock_irqrestore() at the end
of the iteration uses the original flags saved from the
initial irqsave() instead of the flags from the most recent
irqsave(). So it's possible that the interrupt status would
be incorrect at the end of the processing.
Fixes: 0a7fb11c23 ("qed: Add Light L2 support");
CC: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: fc831825f9 ("qed: Add support for hardware offloaded iSCSI")
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When receiving an Rx LL2 packet, qed fails to unmap the previous buffer.
Fixes: 0a7fb11c23 ("qed: Add Light L2 support");
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current Logic would allow the creation of a chain with U32_MAX + 1
elements, when the actual maximum supported by the driver infrastructure
is U32_MAX.
Fixes: a91eb52abb ("qed: Revisit chain implementation")
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Doorbell HW block can be configured at a granularity
of 16 x CIDs, so we need to make sure that the actual number
of CIDs configured would be a multiplication of 16.
Today, when RoCE is enabled - given that the number is unaligned,
doorbelling the higher CIDs would fail to reach the firmware and
would eventually timeout.
Fixes: dbb799c397 ("qed: Initialize hardware for new protocols")
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The num_rec field is 8 bit, so the maximal count number is 255.
This fixes vlans learning not being enabled for wider ranges than 255.
Fixes: a4feea74cd ("mlxsw: reg: Add Switch Port VLAN MAC Learning register definition")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The num_rec field is 8 bit, so the maximal count number is 255. This
fixes vlans not being enabled for wider ranges than 255.
Fixes: b2e345f9a4 ("mlxsw: reg: Add Switch Port VID and Switch Port VLAN Membership registers definitions")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
aszlig observed failing ssh tunnels (-w) during initialization since
commit cc9da6cc4f ("ipv6: addrconf: use stable address generator for
ARPHRD_NONE"). We already had reports that the mentioned commit breaks
Juniper VPN connections. I can't clearly say that the Juniper VPN client
has the same problem, but it is worth a try to hint to this patch.
Because of the early generation of link local addresses, the kernel now
can start asking for routers on the local subnet much earlier than usual.
Those router solicitation packets arrive inside the ssh channels and
should be transmitted to the tun fd before the configuration scripts
might have upped the interface and made it ready for transmission.
ssh polls on the interface and receives back a POLL_OUT. It tries to send
the earily router solicitation packet to the tun interface. Unfortunately
it hasn't been up'ed yet by config scripts, thus failing with -EIO. ssh
doesn't retry again and considers the tun interface broken forever.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=121131
Fixes: cc9da6cc4f ("ipv6: addrconf: use stable address generator for ARPHRD_NONE")
Cc: Bjørn Mork <bjorn@mork.no>
Reported-by: Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
Cc: Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
Reported-by: Jonas Lippuner <jonas@lippuner.ca>
Cc: Jonas Lippuner <jonas@lippuner.ca>
Reported-by: aszlig <aszlig@redmoonstudios.org>
Cc: aszlig <aszlig@redmoonstudios.org>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. modify bd_status from u32 to u16 in function hdlc_rx_done,
because bd_status register is 16bits
2. write bd_length register before writing bd_status register
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit adds support for the GENETv5 implementation.
The GENETv5 reports a major version of 6 instead of 5 so compensate
for this when verifying the configuration of the driver. Also the
EPHY revision is now contained in the MDIO registers of the PHY so
the EPHY revision of 0 in GENET_VER_FMT is expected for GENETv5.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit changes the ioctl handling behavior to return the
EOPNOTSUPP error code instead of the EINVAL error code when an
unknown ioctl command value is detected.
It also removes some redundant parsing of the ioctl command value
and allows the SIOCSHWTSTAMP value to be handled.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reclaim function should return the number of buffer descriptors
reclaimed, not just the number corresponding to skb packets.
Also, remove the unnecessary computation when updating the consumer
index.
While this is not a functional problem it could degrade performance
of napi in a fragmented transmit stream.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the DMA interrupt status is latched and the DMA servicing can be
polled, it is a good idea to clear the latched status of a DMA interrupt
before performing the service that would be invoked by the interrupt.
This prevents old status from causing spurious interrupts when the
interrupt is unmasked at a later time.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bcmgenet_wol_isr() handler performs the necessary processing for
waking from a GENET event. There is no necessary functionality behind
servicing the UMAC_IRQ_MPD_R event in the handling of isr0. Therefore
the code that unmasks and masks this interrupt and that gets invoked
in response to it is removed by this commit.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit moves DMA interrupt enabling out of init_umac() and adds
the masking of these interrupts to the napi enable and disable code.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An assortment of non-functional lines are removed to reduce confusion
and some typos in comments are corrected.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A 2's complement subtraction will always do a borrow, so masking
off the sign bits is the same as conditionally adding (mask+1).
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit adds support for the internal fast ethernet 10/100 PHY
found in the BCM7260, BCM7268, and BCM7271 devices.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The macros MDIO_AN_EEE_ADV_100TX and MDIO_AN_EEE_ADV_1000T are now
considered obsolete and are replaced in the kernel with the generic
macros MDIO_EEE_100TX and MDIO_EEE_1000T respectively.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The required changes in the function vxlan_dev_create() were missing
in commit 8bcdc4f3a2.
The vxlan device is not registered anymore after this patch and the error
path causes an stack dump:
WARNING: CPU: 3 PID: 1498 at net/core/dev.c:6713 rollback_registered_many+0x9d/0x3f0
Fixes: 8bcdc4f3a2 ("vxlan: add changelink support")
CC: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch advances the qed* drivers into using the newer firmware -
This solves several firmware bugs, mostly related [but not limited to]
various init/deinit issues in various offloaded protocols.
It also introduces a major 4-Cached SGE change in firmware, which can be
seen in the storage drivers' changes.
In addition, this firmware is required for supporting the new QL41xxx
series of adapters; While this patch doesn't add the actual support,
the firmware contains the necessary initialization & firmware logic to
operate such adapters [actual support would be added later on].
Changes from Previous versions:
-------------------------------
- V2 - fix kbuild-test robot warnings
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Manish Rangankar <Manish.Rangankar@cavium.com>
Signed-off-by: Chad Dupuis <Chad.Dupuis@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Having the socket present in context simplifies the sending logic.
It also fixes the invalid assumption that we have to use the same
sending socket for all client IP's on a specific gtp interface.
Signed-off-by: Andreas Schultz <aschultz@tpip.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This unifies duplicate code into a helper. It also prepares the
groundwork to add a lookup version that uses the socket to find
attached pdp contexts.
Signed-off-by: Andreas Schultz <aschultz@tpip.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add network device to gtp context in preparation for splitting
the TEID from the network device.
Use this to rework the socker rx path. Move the common RX part
of v0 and v1 into a helper. Also move the final rx part into
that helper as well.
Signed-off-by: Andreas Schultz <aschultz@tpip.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both function are always used together with the final goal to
get the gtp_dev. This simplifies the code by merging them together.
The netdevice lookup is changed to use the regular dev_get_by_index.
The gtp netdevice list is now only used to find the PDP contexts for
imcomming packets. It can be completely eliminated Once the TEID
hash is moved into the GTP socket.
Signed-off-by: Andreas Schultz <aschultz@tpip.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Having both GTPv0-U and GTPv1-U is not always desirable.
Fallback from GTPv1-U to GTPv0-U was depreciated from 3GPP
Rel-8 onwards. Post Rel-8 implementation are discuraged
from listening on the v0 port (see 3GPP TS 29.281, Sect. 1).
A future change will completely decouple the sockets from the
network device. Till then, at least one of the sockets needs to
be specified (either v0 or v1), the other is optional.
Signed-off-by: Andreas Schultz <aschultz@tpip.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
After enabling the UDP encapsulation, only the sk member is used.
Holding the socket would prevent user space from closing the socket,
but holding a reference to the sk member does not have the same
effect.
This change will make it simpler to later detach the sockets from
the netdevice.
Signed-off-by: Andreas Schultz <aschultz@tpip.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer or accessing memory beyond the endpoint array should a
malicious device lack the expected endpoints.
The endpoints are specifically dereferenced in the i2400m_bootrom_init
path during probe (e.g. in i2400mu_tx_bulk_out).
Fixes: f398e4240f ("i2400m/USB: probe/disconnect, dev init/shutdown
and reset backends")
Cc: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the rx queue default size when dma interrupts are treated,
since dma op mode can be also set there.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch configures default number of RX and TX queues when
using the pci glue driver.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace init_timer with setup_timer to simplify the source code.
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new operation to disable the DA, SA and VTU priority override.
Setting such limit is not likely to be used soon, so provide a
port_disable_pri_override operation directly. This can be changed later
for port_set_pri_override when we'll need it.
Also remove the now obsolete mv88e6xxx_6320_family helper.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new operation to disable the limiting of learnt MAC addresses.
Setting such limit is not likely to be used soon, so provide a
port_disable_learn_limit operation directly. This can be changed later
for port_set_learn_limit when we'll need it.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Marvell switch ports can be configured to allow or prevent egress of
frames with an unknown unicast or multicast destination address.
Some switch chips such as 88E6095 and 88E6185 have two disjoint bits in
Port Control Register (0x04) bit 2 "Forward Unknown" (for unicast) and
Port Control 2 Register (0x08) bit 6 "Default Forward" (for multicast).
Other chips such as 88E6085, 88E6123, 88E6352, and 88E6390 have a 2-bit
value in Port Control Register (0x04) bits 3:2 "EgressFloods".
The current code does not fully implement the disjoint bits variant and
assigns incorrect ones to some chip models. Fix that with two
implementation references (6185 and 6352 that I currently have) of a
port_set_egress_floods operation (as named in datasheets).
Old chips such as 88E6060 don't have egress flooding mode, so don't
error out if the operation is not provided.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A switch port mode is defined by the association of its egress mode, its
frame mode and if supported or required, the ether type value.
Pack all this in a mv88e6xxx_set_port_mode function and provide helpers
for the Normal Network mode, the DSA mode, and the Ether Type DSA mode,
as well as an helper to setup a port's mode depending on its nature.
Define PORT_ETH_TYPE_DEFAULT for the 0x9100 reset value of port E Type.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all Marvell switch chips support port trunking, which is embedded in
the port vector data for ATU operations.
Rename the portv_trunkid member of the mv88e6xxx_atu_entry structure to
portvec to be more concise and consistent with the different chips.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the _mv88e6xxx_fid_new helper to mv88e6xxx_atu_new to get rid of
the old underscore prefix naming convention and be consistent with the
rest of the chip-wide ATU API.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a fresh documented implementation of the ATU Move operation, and use
it to replace the current ATU Remove operation.
Note that not all Marvell switch chip support the ATU Move operation.
For those supporting it, the number of bits used to mask the destination
port may vary. 6352 and such use 4-bit, while 6390 use 5-bit. Thus add a
new atu_move_port_mask member in the info structure to describe the
presence and variant of ATU Move operation.
Note that the ATU Move operation is not documented in the 6185 datasheet
but the chip does support the operation.
All remaining _mv88e6xxx_atu_* functions are now unused as well as the
MV88E6XXX_FLAG_G1_ATU_FID flag, thus remove them.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a fresh documented implementation of the ATU Flush/Move operation.
Use it to replace the current ATU Flush operation.
_mv88e6xxx_atu_flush_move is still used by the Move operation so keep it
until the Move operation is refactored in a next commit.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add and use a fresh documented implementation of the ATU GetNext.
Since it is not necessary to write the MAC address to iterate from, only
do it once directly in the ATU GetNext operation, if the provided ATU
entry structure is not valid. This makes the user code simpler.
Also, there is no need to loop when getting a single ATU entry. So
remove the mv88e6xxx_atu_get helper and add a simpler snippet in
mv88e6xxx_port_db_load_purge to lookup a given MAC address.
The _mv88e6xxx_atu_mac_{read,write} are not used anymore thus remove
them. _mv88e6xxx_atu_data_{read,write} are still used so keep them.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All Marvell switch chips have an ATU accessed using the same Global (1)
register layout. Only the handling of the FID differs as more bits were
necessary to support more and more databases.
Add and use a fresh documented implementation of the ATU Load/Purge.
The static mv88e6xxx_g1_atu_{fid_write,op_wait,op,data_write,mac_write}
functions won't need to be exposed in the end so for the moment keep
their counterparts _mv88e6xxx_atu_{wait,cmd,data_write,mac_write} as is,
since they are still used by other ATU operations.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ATU Learn2All feature allows newly learnt addresses to be spanned on
ports marked as "Message Port", currently all DSA ports.
This commit enables this feature which is necessary and quite convenient
for multi-chip switch fabrics.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All interconnectable Marvell switch chips have an ATU Learn2All feature
which allows newly learnt addresses to be spanned on ports marked as
"Message Port".
This commit configures the DSA ports as Message Port. Note that this has
no effect until the Learn2All feature is enabled.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the configuration of the default ageing time in a new
mv88e6xxx_atu_setup function.
That function will be extended later to contain all ATU related
configuration bits.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the ATU ageing time setter code in a new global1_atu.c file, which
will be extended in future patches to contains all consequent Global (1)
ATU support code.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a mv88e6xxx_port_mask() helper to get the bitmask of ports in a
switch chip, that will be used in several features.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for TC flower offload statistics including number of packets,
bytes and last use timestamp. Currently the statistics are gathered on a
per-rule basis.
Signed-off-by: Arkadi Sharshvesky <arkadis@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for packets and byte statistics on TCAM entries. The counters
are allocated from the generic flow counters pool.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for Policing and Counting action block. This action block
will be used to bind counter to TCAM entries.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce periodic task for dumping the activity status for the ACL
rule TCAM entries. This is done in order to emulate last use statistics.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.comi>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the ACL rules can be accessed only by hashing. In order to
dump the activity the rules are also placed in a list.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for retrieving TCAM entry activity. In order to support ACL
rule activity corresponding TCAM entry should be queried.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for allocating generic flow counter. Generic flow counter
can count packets or packets and bytes and can be assigned to different
hardware processes. First use will be for counting packets and bytes of
ACL rules, and will be introduced in the following patches.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Ido schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MGPC register retrieves generic flow counter value. It will be
used to query ACL counters.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add implementation for counter allocator. The ASIC has special memory
pool for various counting purposes. Counter memory is distributed between
equal size banks.
The static sub-pool configuration should specify the following parameters
for each sub-pool:
- Number of required banks.
- Maximum entry size.
Each module can add dedicated sub-pool or use existing one.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some cases during XenBus disconnect event handling and subsequent
queue resource release there may be some TX handlers active on
other processors. Use RCU in order to synchronize with them.
Signed-off-by: Igor Druzhinin <igor.druzhinin@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support prepending data from XDP. We are already always allocating
some headroom because FW may prepend metadata to packets.
xdp_adjust_head() can be supported by making sure that headroom is
big enough for XDP. In case FW had prepended metadata to the packet,
however, we have to move it out of the way before we call XDP.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
XDP may require us to move metadata to make room for pushing
headers. Track meta data location with a pointer and pass
it explicitly to functions.
While at it validate that meta_len from the descriptor is not
bogus.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename pkt_off variable to dma_off, it should hold data offset
counting from beginning of DMA mapping. Compute the value only
in XDP context.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NFP_NET_CFG_RX_OFFSET is 32bit wide, make sure what we read from
there is reasonable for packet headroom. This allows us to store
the rx_offset in a 8bit variable.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of testing if xdp_prog is present store the dma direction
in data path structure.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of passing around sets of rings and their parameters just
store all information in the data path structure.
We will no longer user xchg() on XDP programs when we swap programs
while the traffic is guaranteed not to be flowing. This allows us
to simply assign the entire data path structures instead of copying
field by field.
The optimization to reallocate only the rings on the side (RX/TX)
which has been changed is also removed since it seems like it's not
worth the code complexity.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use xdp_prog member of data path struct to carry the xdp_prog to
alloc/free free functions.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the mtu member from ring set to data path struct.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use fl_bufsz member of data path struct to carry desired size of
free list entries.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of passing variables around use dp to store number of tx rings
for the stack and number of IRQ vectors.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make callers of nfp_net_ring_reconfig() pass newly allocated data
path structure. We will gradually make use of that structure
instead of passing parameters around to all the allocation functions.
This commit adds allocation and propagation of new data path struct,
no parameters are converted, yet.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Control BAR pointer is used to unmask interrupts so it should be
in the first cacheline of adapter structure.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move all data path information into a separate structure. This way
we will be able to allocate new data path with all new rings etc.
and swap it in easily.
No functional changes.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the configuration of the AVB Credit-Based Shaper.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch prepares mac debug dump for multiple queues.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch prepares mac irq status treatment for multiple queues.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adapts flow_ctrl function to prepare it for multiple queues.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the functionality of RX queue to dma channel mapping
based on configuration.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces the enabling of RX queues as DCB or as AVB based
on configuration.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the RX and TX scheduling algorithms programming.
It introduces the multiple queues configuration function
(stmmac_mtl_configuration) in stmmac_main.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the multiple queues configuration in the Device Tree.
It was also created a set of structures to keep the RX and TX queues
configurations to be used in the driver.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NVIDIA Tegra186 SoC contains an instance of the Synopsys DWC
ethernet QOS IP core. The binding that it uses is slightly different
from existing ones because of the integration (clocks, resets, ...).
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split out the binding specific parts of ->probe() and ->remove() to
enable the driver to support variants of the binding. This is useful in
order to keep backwards-compatibility while making it easy for a sub-
driver to deal only with the updated bindings rather than having to add
compatibility quirks all over the place.
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Reviewed-By: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Program the receive queue size based on the RX FIFO size and enable
hardware flow control for large FIFOs.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New version of this core encode the FIFO sizes in one of the feature
registers. Use these sizes as default, but still allow device tree to
override them for backwards compatibility.
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When DMA mapping an SKB fragment, the mapping must be checked for
errors, otherwise the DMA debug code will complain upon unmap.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
clk_prepare_enable() and clk_disable_unprepare() for this clock aren't
properly balanced, which can trigger a WARN_ON() in the common clock
framework.
Reviewed-By: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an error occurs while opening the device, make sure to disable the
PTP reference clock.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an error occurs while opening the device, make sure that both the TX
timer and the PHY are properly cleaned up.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There aren't currently any users of the "clk_ptp_ref", but there are
other references to "ptp_ref", so I'm leaning towards considering that a
typo. Fix it.
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When sending a L3 miss, the family is set to AF_INET even for IPv6. This
causes userland (eg "ip monitor") to be confused. Ensure we send the
appropriate family in this case. For L2 miss, keep using AF_INET.
Signed-off-by: Vincent Bernat <vincent@bernat.im>
Signed-off-by: David S. Miller <davem@davemloft.net>
Optimize DMA in NUMA systems by allocating memory from NUMA node that NIC
is plugged in to; DMA will no longer cross NUMA nodes. If NIC IRQs are
pinned to a local CPU, that CPU's access to the DMA'd data is also
optimized.
Signed-off-by: VSR Burru <veerasenareddy.burru@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@cavium.com>
Signed-off-by: Satanand Burla <satananda.burla@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code in netvsc_device_remove was incorrectly calling napi_disable
repeatedly on the same element. This would cause attempts
to remove netvsc module to hang.
Fixes: 2506b1dc4bbe ("netvsc: implement NAPI")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since rndis_halt_device waits until all outstanding sends and
receives are completed. Netvsc device needs to still schedule
NAPI to see those completions.
Fixes: 2506b1dc4bbe ("netvsc: implement NAPI")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the send indirection table from the inner device (netvsc)
to the network device context.
It is possible that netvsc_device is not present (remove in progress).
This solves potential use after free issues when packet is being
created during MTU change, shutdown, or queue count changes.
Fixes: d8e18ee0fa ("netvsc: enhance transmit select_queue")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a network interface controlled by the aquantia ethernet driver is brought
down a warning is output in dmesg (see below).
The problem is that aq_pci_func_free_irqs() is calling free_irq() before it is
calling irq_set_affinity_hint().
WARNING: CPU: 4 PID: 10068 at kernel/irq/manage.c:1503 __free_irq+0x24d/0x2b0
<snip>
Call Trace:
dump_stack+0x63/0x87
__warn+0xd1/0xf0
warn_slowpath_null+0x1d/0x20
__free_irq+0x24d/0x2b0
free_irq+0x39/0x90
aq_pci_func_free_irqs+0x52/0xa0 [atlantic]
aq_nic_stop+0xca/0xd0 [atlantic]
aq_ndev_close+0x1d/0x40 [atlantic]
__dev_close_many+0x99/0x100
__dev_close+0x67/0xb0
<snip>
Fixes: 36a4a50f40 ("net: ethernet: aquantia: switch to pci_alloc_irq_vectors")
Cc: Christoph Hellwig <hch@lst.de>
Cc: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: David Arcari <darcari@redhat.com>
Tested-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Madalin Bucur says:
====================
QorIQ DPAA 1 updates
This patch set introduces a series of fixes and features to the DPAA 1
drivers. Besides activating hardware Rx checksum offloading, four traffic
classes are added for Tx traffic prioritisation.
changes from v1: added patch to enable context-A stashing
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Tested-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change packet type handler to ETH_P_IP instead of ETH_P_ALL
since we are already expecting an IP packet.
Also, using ETH_P_ALL will cause the loopback test packet type handler
to be called on all outgoing packets, especially our own self loopback
test SKB, which will be validated on xmit as well, and we don't want that.
Tested with:
ethtool -t ethX
validated that the loopback test passes.
Fixes: 0952da791c ('net/mlx5e: Add support for loopback selftest')
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When deleting offloaded TC flows, we must correctly identify E-switch
rules. The current check could get us wrong w.r.t to rules set on the
PF. Since it's possible to set NIC rules on the PF, switch to SRIOV
offloads mode and then attempt to delete a NIC rule.
To solve that, we add a flags field to offloaded rules, set it on
creation time and use that over the code where currently needed.
Fixes: 8b32580df1 ('net/mlx5e: Add TC vlan action for SRIOV offloads')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the function setdcbx fails if the request dcbx mode
is either IEEE or CEE. We remove the IEEE/CEE mode check because
we support both IEEE and CEE interfaces.
Fixes: 3a6a931dfb ("net/mlx5e: Support DCBX CEE API")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a PCI error is detected the PCI state could be corrupt, don't save
it in that flow. Save the state after initialization. After restoring the
PCI state during slot reset save it again, restoring the state destroys
the previously saved state info.
Fixes: 05ac2c0b74 ('net/mlx5: Fix race between PCI error handlers and
health work')
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The autogroups list is a list of non overlapping group boundaries
sorted by their start index. If the autogroups list wasn't empty
and an empty group slot was found at the start of the list,
the new group was added to the end of the list instead of the
beginning, as the prev initializer was incorrect.
When this was repeated, it caused multiple groups to have
overlapping boundaries.
Fixed that by correctly initializing the prev pointer to the
start of the list.
Fixes: eccec8da3b ('net/mlx5: Keep autogroups list ordered')
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the abort mechanism is invoked it binds the first virtual router
(VR) to an LPM tree and inserts a default route to direct packets to the
CPU.
With VRFs, we can have router interfaces (RIFs) bound to multiple VRs,
so we need to make sure packets are trapped from all VRs and not just
the first one.
Upon abort invocation, bind all active VRs to the same LPM tree and
insert a default route in each.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until now we implicitly associated all the router interfaces (RIFs)
with the first virtual router (VR). This must be changed in order to
enable VRF offload. Otherwise, a packet received via a VRF slave would
do a FIB lookup in the same table used by other VRFs.
Instead, bind the RIF to a VR according to the table where FIB lookup
should be performed for packets received via the RIF.
Currently, we only care about the MAIN and LOCAL tables (which we squash
together).
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A virtual router (VR) is an entity within the device to which routing
tables and interfaces can be bound to. It can be used to implement VRFs.
In the initial implementation we associated the VR with a specific
protocol (e.g., IPv4) and an LPM tree. However, this isn't really
accurate, as the same VR can be used for both IPv4 and IPv6 traffic, by
binding a different LPM tree to a {VR, Proto} pair.
This patch aims to restructure the VR code according to the above logic,
so that VRs are more accurately represented by the driver's data
structures. The main motivation behind this change is to prepare the
driver for VRF offload.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When looking for a new LPM tree we should always consider all the unused
trees. It doesn't matter if the new tree is required due to changes in
currently used prefixes inside an existing routing table or because a
route was inserted into an empty table.
Both cases are functionally identical and therefore should be treated
the same.
When looking for a new LPM tree, consider all unused trees and don't
reserve trees for specific cases.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The inetaddr notification block is currently implemented in the main
driver file, but this isn't really appropriate, as it mainly creates and
destroys router interfaces (RIFs) which belong with the rest of the
router code.
This will become even more apparent later on when we'll need to bind
these RIFs to virtual routers according to the VRF's table.
Structure the driver better and prevent unnecessary function exports by
moving the RIF related code with the rest of the router code.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow 'unreachable', 'blackhole' and 'prohibit' route types to be
programmed into the device by sending any packet hitting them to the
CPU.
This is needed so that users will be able to program a default route
into the VRF's table, thereby preventing lookup from leaking to other
tables.
Audit the code paths to make sure we don't rely on the presence of a
nexthop netdev, as it doesn't exist for above mentioned route types.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We only use the RIF reference count to determine when the last IP
address was removed, but instead we can just test 'in_dev->ifa_list'.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a VLAN device is configured on top of a LAG device (f.e.,
bond0.10), a vPort is created on top of each of the LAG's slaves and its
'dev' pointer is set to the VLAN device.
This is in contrast to the implicit PVID vPort (representing 'bond0'),
whose 'dev' pointer keeps pointing to the port netdev itself (f.e.,
'sw1p1').
Make both cases consistent by setting their 'dev' pointer to the actual
netdev they represent. Either the LAG device itself (in the case of the
PVID vPort) or the VLAN device on top of it.
This will later allow us to more easily understand for which netdev we
should create the router interface (RIF) upon enslavement to a VRF
master.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an upper device is configured on top of a vPort we make sure it's a
bridge master during PRECHANGEUPPER and fail otherwise. Therefore, when
CHANGEUPPER is later received we don't bother checking the upper's type.
Make the code more extendable in preparation for VRF uppers, by checking
the upper's type.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're going to allow bridges stacked on top of port netdevs to be
enslaved to a VRF, but for now, only VLAN uppers of the VLAN-aware
bridge are supported.
Sanitize any other bridge upper. This is consistent with the way we
sanitize port netdevs' uppers.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hwmon temperature sensor devices is registered using a devm_hwmon
API call. The marvell_release() would then manually free the device,
not using a devm_hmon API, resulting in the device being removed
twice, leading to a crash in kernfs_find_ns() during the second
removal.
Remove the manual removal, which makes marvell_release() empty, so
remove it as well.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Fixes: 0b04680fda ("phy: marvell: Add support for temperature sensor")
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bcmgenet_tx_reclaim() function is used to reclaim transmit
resources in different places within the driver. Most of them
should not affect the state of the transmit flow control.
This commit relocates the logic for waking tx queues based on
freed resources to the napi polling function where it is more
appropriate.
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure clock is enabled for ethtool ops.
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Edwin Chan <edwin.chan@broadcom.com>
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using the internal PHY it must be powered up when the MII is probed
or the PHY will not be detected. Since the PHY is powered up at reset
this has not been a problem. However, when the kernel is restarted with
kexec the PHY will likely be powered down when the kernel starts so it
will not be detected and the Ethernet link will not be established.
This commit explicitly powers up the internal PHY when the GENET driver
is probed to correct this behavior.
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a spinlock to ensure that irq0_stat is not unintentionally altered
as the result of preemption. Also removed unserviced irq0 interrupts
and removed irq1_stat since there is no bottom half service for those
interrupts.
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the internal PHY is powered up during the open and resume
functions it should be powered back down if the functions fail.
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reserved gphy_rev value of 0x01ff must be tested before the old
or new scheme for GPHY major versioning are tested, otherwise it will
be treated as 0xff00 according to the old scheme.
Fixes: b04a2f5b9f ("net: bcmgenet: add support for new GENET PHY revision scheme")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The gap between the Tx status counters and the Rx RUNT counters is now
being added to allow correct reporting of the registers.
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The location of the RBUF overflow and error counters has moved between
different version of the GENET MAC. This commit corrects the driver to
read from the correct locations depending on the version of the GENET
MAC.
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce MLXSW_AFK_ELEMENT_VID, PCP and declare them in afk_element
infos that contain them. Use the elements when VLAD ID or priority are
used in the flow.
Also add MLXSW_AFK_ELEMENT_VID, PCP to mlxsw_sp_acl_tcam_pattern_ipv4.
Both items are included in mlxsw_sp_afk_element_info_l2_dmac,
resp. _smac, and both MLXSW_AFK_ELEMENT_SMAC and _DMAC are already in
the pattern.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add VLAN action offloading. Invoke it from Spectrum flower handler for
"vlan modify" actions.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Depending on the hardware, the amd-xgbe driver may use disable_irq_nosync()
and enable_irq() when an interrupt is received to process Rx packets. If
the napi_complete_done() return value isn't checked an unbalanced enable
for the IRQ could result, generating a warning stack trace.
Update the driver to only enable interrupts if napi_complete_done() returns
true.
Reported-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In original driver was implemented support for half-
and full-duplex modes, but it was not enabled. Instead
of it ks8851_rx_1msg method always returns "true" that
means "full-duplex" mode.
This patch replaces hard-coded functionality with
flexible solution that supports both SPI modes.
Signed-off-by: Sergey Shcherbakov <shchers@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some situations, the firmware will return 0 for autoneg supported
speed. This may happen if the firmware detects no SFP module, for
example. The driver should ignore this so that we don't end up with
an invalid autoneg setting with nothing advertised. When SFP module
is inserted, we'll get the updated settings from firmware at that time.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set DCB_CAP_DCBX_HOST capability flag only if the firmware LLDP agent
is not running.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we call bnxt_reset_task() due to tx timeout, we should call
bnxt_ulp_stop() to inform the RDMA driver about the error and the
impending reset.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The firmware call to do function reset is done too late. It is causing
the rings that have been reserved to be freed. In NPAR mode, this bug
is causing us to run out of rings.
Fixes: 391be5c273 ("bnxt_en: Implement new scheme to reserve tx rings.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many of the bond param variables are declared global while it's not
really necessary for these variables to be global. So moving them to
the location these are used.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
LACP state-machine defines "port-moved" state when the same ActorSystemID
and Port are seen in a LACPDU received on different port. The state is
never set since it's not implemented. However the state-machine attempts
to clear that state occasionally. LACP state machine is already complicated
and since this state is not implemented, removing it's checks makes the
state-machine little simpler.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eliminate hard-coded value and use the default that is set.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initializing work-queues every time ifup operation performed is unnecessary
and can be performed only once when the port is created.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to move the work-queue initialization to port creation
from current port_open phase. Work-queue initialization does not make
sense every time we do 'ifup/ifdown'. So moving to port creation phase.
Arp monitoring work depends on the bonding mode and that is not tied
to the port creation and can change anytime during the life after port
creation. So this restructuring allows us to move the initialization
at creation without losing the ability to arm the correct work for the
mode user has selected.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Printing copyright does not give any useful information on the boot
process.
Furthermore, the email address printed is obsolete since
commit ba57b6f204 ("MAINTAINERS: fix bouncing tun/tap entries")
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix typos and add the following to the scripts/spelling.txt:
overide||override
While we are here, fix the doubled "address" in the touched line
Documentation/devicetree/bindings/regulator/ti-abb-regulator.txt.
Also, fix the comment block style in the touched hunks in
drivers/media/dvb-frontends/drx39xyj/drx_driver.h.
Link: http://lkml.kernel.org/r/1481573103-11329-21-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix typos and add the following to the scripts/spelling.txt:
disble||disable
disbled||disabled
I kept the TSL2563_INT_DISBLED in /drivers/iio/light/tsl2563.c
untouched. The macro is not referenced at all, but this commit is
touching only comment blocks just in case.
Link: http://lkml.kernel.org/r/1481573103-11329-20-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Prevent theoretical buffer overrun by returning an error if
the number of entries returned by the firmware does not match those
present.
Also use a common handling error path.
Found by inspection.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Tested-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We only need FW version in the first cache line of adapter struct
because we need to know the metadata format. To save space add a
metadata format bit.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of return code from napi_complete_done() to avoid rearming
interrupts when busy polling is on.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We really only need the device pointer on the fast path, stash it at
the beginning of the adapter structure and move pci_dev pointer down.
This saves up a few lines of code.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reorder variables longest to shortest to comply with netdev coding style.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We already print most of ring configuration including descriptors
in debugfs, add the few missing pieces and remove debug prints.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NSP reports to us port labels. First id is the id of the physical
port, the other one tells us which logical interface is it within a
split port. Instead of printing them as string keep them in integer
format. Compute which interfaces are part of port split.
On netdev side use port labels and split information to provide a
.ndo_get_phys_port_name() implementation. We follow the name format
of mlxsw which is also suggested in "Port Netdev Naming" section
of Documentation/networking/switchdev.txt.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some firmware images may reuse CRC32 hardware to compute RXHASH.
Make sure we report the correct hash function. Note that we don't
support changing functions at runtime. That would also require
a few more additions to the way the key is set because different
functions have different key sizes.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Synopsys provides a new DesignWare Core Enterprise Ethernet MAC
IP (DWC-XLGMAC) for Ethernet designs. It is compliant with the
IEEE 802.3-2012 specifications, including IEEE 802.3ba and
consortium specifications.
This patch provides the initial 25G/40G/50G/100G Ethernet driver
for Synopsys XLGMAC IP Prototyping Kit.
Signed-off-by: Jie Deng <jiedeng@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a MAINTAINERS entry for the ethernet driver for
the on-chip ethernet interface which uses a linked list of DMA
descriptor architecture (v2) for APM X-Gene SoCs.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Keyur Chudgar <kchudgar@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds,
- Transmit
- Transmit completion poll
- Receive poll
- NAPI handler
and enables the driver.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Keyur Chudgar <kchudgar@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
